DVP-4000 Service Manual

SERVICE MANUAL

DVD PLAYER

ModelDVP-4000

TABLE OF CONTENTS

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-1LASER BEAM SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-1IMPORTANT SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3-1STANDARD NOTES FOR SERVICING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4-1CABINET DISASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5-1BLOCK DIAGRAMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6-1SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7-1WAVEFORMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8-1WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9-1FIRMWARE RENEWAL MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10-1SYSTEM CONTROL TIMING CHARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11-1IC PIN FUNCTION DESCRIPTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12-1LEAD IDENTIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13-1EXPLODED VIEWS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14-1MECHANICAL PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15-1ELECTRICAL PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16-1

Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories.

1-1-1 E57A0SP

SPECIFICATIONS

NOTES:1. All Items are measured without pre-emphasis unless otherwise specified.2. Power supply : AC230 V 60 Hz3. Load imp. : 100 K ohm

4. Room ambient : 5 °C ~ 40 °C

ITEM CONDITIONS UNIT NOMINAL LIMIT

1. Video Output 75 ohm load Vpp 1.0 ± 0.1

2. Optical Digital Out dBm -18

3. Audio (PCM)

3-1. Output Level 1kHz 0dB Vrms 2.0

3-2. S/N dB 110

3-3. Freq. Response

DVD fs=48kHz 20~22kHz dB ± 0.5

CD fs=44.1kHz 20~20 kHz dB ± 0.5

3-4. THD+N

DVD 1 kHz 0dB % 0.0025

CD 1 kHz 0dB % 0.003

1-2-1 DVD_LASER

LASER BEAM SAFETY PRECAUTIONS

This DVD player uses a pickup that emits a laser beam.

The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keepyour eyes at least 30cm away from the pickup lens when the diode is turned on. Do not look directly at the laserbeam.

Caution: Use of controls and adjustments, or doing procedures other than those specified herein, may result inhazardous radiation exposure.

Do not look directly at the laser beam comingfrom the pickup or allow it to strike againstyour skin.

Drive Mecha Assembly

Laser Beam Radiation

Laser Pickup

Turntable

1-3-1 DVD_SFNP

IMPORTANT SAFETY PRECAUTIONS

Product Safety NoticeSome electrical and mechanical parts have specialsafety-related characteristics which are often not evi-dent from visual inspection, nor can the protection theygive necessarily be obtained by replacing them withcomponents rated for higher voltage, wattage, etc.Parts that have special safety characteristics are iden-tified by a ! on schematics and in parts lists. Use of asubstitute replacement that does not have the samesafety characteristics as the recommended replace-ment part might create shock, fire, and/or other haz-ards. The Product’s Safety is under reviewcontinuously and new instructions are issued when-ever appropriate. Prior to shipment from the factory,our products are carefully inspected to confirm withthe recognized product safety and electrical codes ofthe countries in which they are to be sold. However, inorder to maintain such compliance, it is equally impor-tant to implement the following precautions when a setis being serviced.

Precautions during ServicingA. Parts identified by the ! symbol are critical for

safety. Replace only with part number specified.

B. In addition to safety, other parts and assembliesare specified for conformance with regulationsapplying to spurious radiation. These must also bereplaced only with specified replacements.Examples: RF converters, RF cables, noise block-ing capacitors, and noise blocking filters, etc.

C. Use specified internal wiring. Note especially:

1)Wires covered with PVC tubing2)Double insulated wires3)High voltage leads

D. Use specified insulating materials for hazardouslive parts. Note especially:

1)Insulation tape2)PVC tubing 3)Spacers4)Insulators for transistors

E. When replacing AC primary side components(transformers, power cord, etc.), wrap ends ofwires securely about the terminals before solder-ing.

F. Observe that the wires do not contact heat produc-ing parts (heatsinks, oxide metal film resistors, fus-ible resistors, etc.).

G. Check that replaced wires do not contact sharpedges or pointed parts.

H. When a power cord has been replaced, check that5 - 6 kg of force in any direction will not loosen it.

I. Also check areas surrounding repaired locations.

J. Be careful that foreign objects (screws, solderdroplets, etc.) do not remain inside the set.

K. Crimp type wire connectorThe power transformer uses crimp type connectorswhich connect the power cord and the primary sideof the transformer. When replacing the transformer,follow these steps carefully and precisely to preventshock hazards.Replacement procedure

1)Remove the old connector by cutting the wires at apoint close to the connector.Important: Do not re-use a connector. (Discard it.)

2)Strip about 15 mm of the insulation from the endsof the wires. If the wires are stranded, twist thestrands to avoid frayed conductors.

3)Align the lengths of the wires to be connected.Insert the wires fully into the connector.

4)Use a crimping tool to crimp the metal sleeve at itscenter. Be sure to crimp fully to the complete clo-sure of the tool.

L. When connecting or disconnecting the internalconnectors, first, disconnect the AC plug from theAC outlet.

1-3-2 DVD_SFNP

Chassis or Secondary Conductor

dd'

Primary Circuit Terminals

AC Voltmeter(High Impedance)

Exposed Accessible Part

B One side of Power Cord Plug Prongs

Z

Safety Check after ServicingExamine the area surrounding the repaired location fordamage or deterioration. Observe that screws, parts,and wires have been returned to their original posi-tions. Afterwards, do the following tests and confirmthe specified values to verify compliance with safetystandards.

1. Clearance DistanceWhen replacing primary circuit components, confirmspecified clearance distance (d) and (d’) between sol-dered terminals, and between terminals and surround-ing metallic parts. (See Fig. 1)

Table 1 : Ratings for selected area

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

2. Leakage Current TestConfirm the specified (or lower) leakage currentbetween B (earth ground, power cord plug prongs)and externally exposed accessible parts (RF termi-nals, antenna terminals, video and audio input andoutput terminals, microphone jacks, earphone jacks,etc.) is lower than or equal to the specified value in thetable below.

Measuring Method (Power ON) :Insert load Z between B (earth ground, power cordplug prongs) and exposed accessible parts. Use anAC voltmeter to measure across the terminals of loadZ. See Fig. 2 and the following table.

AC Line Voltage Clearance Distance (d) (d’)

230 V≥ 3mm(d)≥ 6 mm(d’)

Fig. 1

Fig. 2

Table 2: Leakage current ratings for selected areas

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

AC Line Voltage Load Z Leakage Current (i) One side of power cord plug prongs (B) to:

230 V

2kΩ RES. Connected in

parallel

i≤0.7mA AC Peaki≤2mA DC

RF orAntenna terminals

50kΩ RES. Connected in

parallel

i≤0.7mA AC Peaki≤2mA DC A/V Input, Output

1-4-1 DVD_NOTE

STANDARD NOTES FOR SERVICING

Circuit Board Indications1. The output pin of the 3 pin Regulator ICs is indi-

cated as shown.

2. For other ICs, pin 1 and every fifth pin are indicatedas shown.

3. The 1st pin of every male connector is indicated asshown.

Instructions for Connectors1. When you connect or disconnect the FFC (Flexible

Foil Connector) cable, be sure to first disconnectthe AC cord.

2. FFC (Flexible Foil Connector) cable should beinserted parallel into the connector, not at an angle.

How to Remove / Install Flat Pack-IC

1. RemovalWith Hot-Air Flat Pack-IC Desoldering Machine:.(1) Prepare the hot-air flat pack-IC desoldering

machine, then apply hot air to the Flat Pack-IC(about 5 to 6 seconds). (Fig. S-1-1)

(2) Remove the flat pack-IC with tweezers while apply-ing the hot air.

(3) Bottom of the flat pack-IC is fixed with glue to theCBA; when removing entire flat pack-IC, first applysoldering iron to center of the flat pack-IC and heatup. Then remove (glue will be melted). (Fig. S-1-6)

(4) Release the flat pack-IC from the CBA using twee-zers. (Fig. S-1-6)

Caution:1. Do not supply hot air to the chip parts around the

flat pack-IC for over 6 seconds because damage tothe chip parts may occur. Put masking tape aroundthe flat pack-IC to protect other parts from damage.(Fig. S-1-2)

2. The flat pack-IC on the CBA is affixed with glue, sobe careful not to break or damage the foil of eachpin or the solder lands under the IC when removingit.

Top View

Out In

Bottom ViewInput

5

10

Pin 1

Pin 1

FFC Cable

Connector

CBA

* Be careful to avoid a short circuit.

Fig. S-1-1

Hot-airFlat Pack-ICDesolderingMachine

CBA

Flat Pack-IC

Tweezers

Masking Tape

Fig. S-1-2

1-4-2 DVD_NOTE

With Soldering Iron:(1) Using desoldering braid, remove the solder from all

pins of the flat pack-IC. When you use solder fluxwhich is applied to all pins of the flat pack-IC, youcan remove it easily. (Fig. S-1-3)

(2) Lift each lead of the flat pack-IC upward one byone, using a sharp pin or wire to which solder willnot adhere (iron wire). When heating the pins, usea fine tip soldering iron or a hot air desolderingmachine. (Fig. S-1-4)



With Iron Wire:(1) Using desoldering braid, remove the solder from all

pins of the flat pack-IC. When you use solder fluxwhich is applied to all pins of the flat pack-IC, youcan remove it easily. (Fig. S-1-3)

(2) Affix the wire to a workbench or solid mountingpoint, as shown in Fig. S-1-5.

(3) While heating the pins using a fine tip solderingiron or hot air blower, pull up the wire as the soldermelts so as to lift the IC leads from the CBA contactpads as shown in Fig. S-1-5



Note:When using a soldering iron, care must be takento ensure that the flat pack-IC is not being held byglue. When the flat pack-IC is removed from theCBA, handle it gently because it may be damagedif force is applied.

Flat Pack-IC Desoldering Braid

Soldering Iron

Fig. S-1-3

Fine TipSoldering Iron

SharpPin

Fig. S-1-4

To Solid Mounting Point

Soldering Iron

Iron Wire

or

Hot Air Blower

Fig. S-1-5

Fine TipSoldering IronCBA

Flat Pack-IC

Tweezers

Fig. S-1-6

1-4-3 DVD_NOTE

2. Installation(1) Using desoldering braid, remove the solder from

the foil of each pin of the flat pack-IC on the CBAso you can install a replacement flat pack-IC moreeasily.

(2) The “I” mark on the flat pack-IC indicates pin 1.(See Fig. S-1-7.) Be sure this mark matches the 1on the PCB when positioning for installation. Thenpresolder the four corners of the flat pack-IC. (SeeFig. S-1-8.)

(3) Solder all pins of the flat pack-IC. Be sure that noneof the pins have solder bridges.

Instructions for Handling Semi-conductorsElectrostatic breakdown of the semi-conductors mayoccur due to a potential difference caused by electro-static charge during unpacking or repair work.

1. Ground for Human BodyBe sure to wear a grounding band (1MΩ) that is prop-erly grounded to remove any static electricity that maybe charged on the body.

2. Ground for Workbench(1) Be sure to place a conductive sheet or copper plate

with proper grounding (1MΩ) on the workbench orother surface, where the semi-conductors are to beplaced. Because the static electricity charge onclothing will not escape through the body ground-ing band, be careful to avoid contacting semi-con-ductors with your clothing.

Example :

Pin 1 of the Flat Pack-ICis indicated by a " " mark.

Fig. S-1-7

Presolder

CBA

Flat Pack-IC

Fig. S-1-8

CBA

< Incorrect >

CBA

Grounding Band

Conductive Sheet orCopper Plate

1MΩ

1MΩ

< Correct >

1-5-1 E57A0DC

CABINET DISASSEMBLY INSTRUCTIONS

1. Disassembly FlowchartThis flowchart indicates the disassembly steps to gainaccess to item(s) to be serviced. When reassembling,follow the steps in reverse order. Bend, route, anddress the cables as they were originally.

2. Disassembly Method

(1): Identification (location) No. of parts in the figures(2): Name of the part(3): Figure Number for reference(4): Identification of parts to be removed, unhooked,

unlocked, released, unplugged, unclamped, ordesoldered.P=Spring, L=Locking Tab, S=Screw,CN=Connector*=Unhook, Unlock, Release, Unplug, or Desoldere.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2)

(5): Refer to “Reference Notes.”

Reference NotesCAUTION 1: Locking Tabs (L-1), (L-2) and (L-3) arefragile. Be careful not to break them.

1-1. Connect the wall plug to an AC outlet and pressthe OPEN/CLOSE button to open the Tray.

1-2. Remove the Tray Panel by releasing two LockingTabs (L-1).

1-3. Press the OPEN/CLOSE button again to closethe Tray.

1-4. Press the POWER button to turn the power off.

1-5. Unplug an AC cord.

1-6. Release two Locking Tabs (L-2). Then, releasefive Locking Tabs (L-3) (to do this, first releasetwo Locking Tabs (A) at the side, and then threeLocking Tabs (B) at the bottom.)

CAUTION 2: Electrostatic breakdown of the laserdiode in the optical system block may occur as apotential difference caused by electrostatic chargeaccumulated on cloth, human body etc, duringunpacking or repair work.

To avoid damage of pickup follow next procedures.

2-1. Disconnect Connector (CN301). Remove threeScrews (S-2) and lift the DVD Mecha. (Fig. D3)

2-2. Slide out the pickup unit as shown in Fig. D4.

2-3. Short the three short lands of FPC cable with sol-der before removing the FFC cable (CN201) fromit. If you disconnect the FFC cable (CN201), thelaser diode of pickup will be destroyed. (Fig. D4)

CAUTION 3: When reassembling, confirm the FFCcable (CN201) is connected completely. Then removethe solder from the three short lands of FPC cable.(Fig. D4)

ID/LOC.No.

PART

REMOVAL

Fig.No.

REMOVE/*UNHOOK/UNLOCK/RELEASE/UNPLUG/DESOLDER

Note

[1] Top Cover D1 5(S-1) -

[2]Front Assembly

D2*2(L-1), Tray Panel, *2(L-2), *5(L-3)

1-11-21-31-41-51-6

[3]DVD Mecha

D3,D4

3(S-2), *CN201, *CN301

22-12-22-33

[4] AV CBA D57(S-3), 3(S-4), *CN1001, *CN1601

-

[5]DVD Main CBA Unit

D5 2(S-5) -

[6]Rear Panel

D6 3(S-6) -

[7]Main CBA Holder

D6 (S-7) -

↓(1)

↓(2)

↓(3)

↓(4)

↓(5)

[1] Top Cover

[2] Front Assembly

[3] DVD Mecha

[5] DVD Main CBA Unit[4] AV CBA

[7] Main CBA Holder[6] Rear Panel

1-5-2 E57A0DC

(S-1)

(S-1)

[1] Top Cover(S-1)

Fig. D1

[2] Front Assembly

Tray Panel

(A)

(A)

(L-3)

(L-2)

(L-1)

(L-1)

(B)Fig. D2

[3] DVD Mecha

(S-2) (S-2)

CN201

CN301

Fig. D3

View for A

Pickup Unit

B

A

Short the three short lands by soldering

View for B

Slide

DVD Mecha

Fig. D4

[4] AV CBA

[5] DVD Main CBA Unit

(S-5)

(S-3)

(S-4)CN1601CN1001

(S-4)

Fig. D5

1-5-3 E57A0DC

(S-6)

[6] Rear Panel

(S-7) [7] Main CBA Holder

Fig. D6

Rotate this roulette in the direction of the arrow

A

View for A

HOW TO MANUAL EJECT1. Remove the Top Case.

2. Rotate the roulette in the direction of the arrow asshown below.

System Control/Servo Block Diagram

E57A0BLS1-6-1 1-6-2

BLOCK DIAGRAMS

59

27

783

15

10

14

26

1

23

4

6

23

5

1718

1211

1413

1516

2524

FP-STB54FP-DIN55FP-DOUT

61REMOTE53FP-CLK

CN401 CN10012

28271

12

789

1011

REMOTESENSOR

RM2001

1G

7G

~

23

17

~

a/KEY-1b/KEY-2c/KEY-3d/KEY-4

e

K1K2

FP-STBFP-DINFP-DOUTFP-CLK

GRID FIP

SEGMENT

FL2001IC2001

DVD MAIN CBA UNIT AV CBADRIVE CBA

(FRONT PANEL CONTROL)IC301(SERVO DRIVE)

IC451(CLOCK GENERATOR)

131416

34

FP-STB 1616FP-DIN 1818FP-DOUT 2020FP-CLK 2121REMOTE 2222

fghi

KEYMATRIX

IC202(OP AMP)

12 14

CN301

FG CBA

FGSENSOR

M

SLED MOTOR

M

SPINDLE MOTOR

IC101(MICRO CONTROLLER)

+-+

-

+-+

-

+-

+-

+-

SLEDMOTORDRIVE

FOCUSACTUATORDRIVE

1/4

1/4 PLL2

X451MULTIPLL

X'TALOSC

36.864MHzOSC

SPINDLEMOTORDRIVE

TRACKINGACTUATORDRIVE

EXT CLOCKCLK33MBE CLOCK

172

170

150

TRAY-OUTTRAY-INFG-IN

97

SLD70

SPDL71

TRACKINGDRIVE

152 FOCUS DRIVE

6066

TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM

FS(+)FS(-)

TS(+)TS(-)

TOVIDEO/ AUDIOBLOCK DIAGRAM

51ADAC-MD

50 ADAC-MC96 ADAC-ML

ADAC-MCADAC-ML

PCM-SCLK

95A-MUTE

ADAC-MDA-MUTE

17

92

FSEL

RESET68RESET

IC461

5 4

+3.3V

TRAY-OUT

TRAY-IN

FOCUS SERVO SIGNAL TRACKING SERVO SIGNAL SLED SERVO SIGNAL SPINDLE SERVO SIGNAL

3SP(+)4SP(-)5TRAY-OUT6TRAY-IN7GND8SL(-)9SL(+)1FG-IN

64 ASPECTASPECT

Digital Signal Process Block Diagram

E57A0BLD1-6-3 1-6-4

C 6D 7A 8B 5F 10E 2

DVD-LD 14CD-LD 12

PD-MONI 13

FS(+) 18FS(-) 19TS(+) 20TS(-) 17

CN201

CN201

CN201

IC201(SW)

IC105 (LATCH)

IC102 (SDRAM) IC101 (MICRO CONTROLLER)

FS

FS(+)

CD/DVD

FS(-)TS(+)TS(-)

TS

PICK-UPUNIT

DETECTOR

CD/DVD 9

Q251,Q252

CD DVD

AMP

Q253,Q254AMP

4

1 3

6

GND(DVD-PD) 15GND(CD-PD) 16

GND(LD) 11

FROM SYSTEM CONTROL/SERVOBLOCK DIAGRAM

RFSIGNALPROCESSCIRCUIT

DVD/CDFORMATTER

AUDIOI/F

VIDEOI/F

NTSC/PALENCODER

DMA

BCU

INST.ROM

32BITCPU

DATAROM

INTERRUPTCONTROLLER

WATCH DOGTIMER

CPUI/FTIMER

DECODERI/F

CPUI/F

READMEMORY

DATAROM

DSPDECODER

PIXELOPERATION

I/OPROCESSOR

INST.ROM

DATAROM

INST.ROM

DATAROM

INST.ROM

SERIAL

D/A

GENERALI/O

INTERRUPTCONTROLLER

TIMER

WATCH DOGTIMER

32BIT CPU

STREAMI/F

EXTERNAL MEMORYI/F

SDRAM

ECC

UMAC

124125122123128129126127131130

135133132134

78

DEBUG

BCU

INSTCACHE

D TYPELATCH

DATACACHE

D/A

D/A

D/A

TO VIDEO/AUDIOBLOCK DIAGRAM

158

164

G

C

R

B

VIDEO-G

VIDEO-C

VIDEO-R

VIDEO-B

TO VIDEO/AUDIOBLOCK DIAGRAM

181SPDIF

175PCM-BCK

176PCM-DATA0

174PCM-LRCLK

161

160

EXADT (0-15), EXADR (16-19)

EXADT (0-15), EXADR (16-19)

EXADT (0-7)

EXADT (8-15)

EXADR (0-7)

EXADR (0-15)EXADR (8-15)

SDRAM DATA(0-31)SDRAM DATA(0-31)

SDRAM ADDRESS(0-10)SDRAM ADDRESS(0-10)

2

9

~

12

19

~

210

235

~

IC104 (LATCH)

D TYPELATCH

2

9

~

12

19

~

2

13

184

205

247

256

~~

~

2

13

31

56

74

85

~~

~

IC103 (FLASH ROM)

FLASHROM

29

36

38

45

~~

DVD MAIN CBA UNIT

DATA(VIDEO/AUDIO) SIGNAL VIDEO SIGNAL DATA(AUDIO) SIGNAL FOCUS SERVO SIGNAL TRACKING SERVO SIGNAL

24

27

60

66

~~

EXADT (0-15)

EXADR (16-19)

~

1

9

16

25

48

~

D/AY VIDEO-Y

163

Video / Audio Block Diagram

E57A0BLV1-6-5 1-6-6

IC601 (AUDIO DAC)

7

8

1211

DIGITALAUDIO OUT

JK1202

JK1201

AMPQ1351

IC1201

Q1203Q1201

Q1202

+3.3V

(AMP)

CN601 CN1601

13 13AUDIO-L15 15AUDIO-R14 14A-L-MUTE16 16A-R-MUTE12 12A-MUTE

AUDIO-LOUT

123

131415

16

FROMSYSTEMCONTROL/SERVOBLOCKDIAGRAM

FROMDIGITALSIGNALPROCESSBLOCKDIAGRAM

SERIALPORT

SERIALCONTROL

4X/8XOVERSAMPLINGDIGITAL FILTER

/FUNCTIONCONTROLLER

ENHANCEDMULTI-LEVELDELTA-SIGMAMODULATOR

DAC LPF+AMPL-CH

R-CHLPF+AMPDAC

ZERO DETECT

SYSTEM CLOCK

12

67

5 AUDIO-ROUT

PCM-BCK

SPDIF

PCM-DATA0PCM-LRCLK

ADAC-MDADAC-MCADAC-ML

PCM-SCLK

AV CBADVD MAIN CBA UNIT

AUDIO SIGNALDATA(AUDIO) SIGNAL

18 18SPDIF

A-MUTE +3.3V

Q1204

WF6

3

WF4

WF5

CN601VIDEO-YVIDEO-C

FROM DIGITALSIGNAL PROCESSBLOCK DIAGRAM

VIDEO SIGNAL

+5V JK1404

1

3AUDIO-LOUT

AUDIO-ROUT

FIBER OPTICTRANS MODULE

IC1204

JK1401S-VIDEOOUT

COMPOSITEVIDEO OUT

CN1601

1 1VIDEO-Y9 9VIDEO-C

3 4

21

IC1401 (VIDEO DRIVER)

6 284dBAMP

2dBAMPLPF DRIVER

Y C

2

334dBAMP

2dBAMPLPF DRIVER

JK1402

31

224dBAMP

2dBAMPLPF DRIVER

194dBAMP

2dBAMPLPF DRIVER16

14

3 3VIDEO-R7 7VIDEO-G

VIDEO-CVBS OUT

VIDEO-ROUT

VIDEO-GOUT

VIDEO-BOUT

JK1404

19

15

11

7

5 5VIDEO-B

254dBAMP

2dBAMPLPF DRIVER12

2 2ASPECTQ1521

Q1522

8 ASPECT

+12V

2dBAMP DRIVER

VIDEO-RVIDEO-GVIDEO-B

ASPECT

WF3

CN601 CN1601FROM SYSTEM CONTROL/SERVOBLOCK DIAGRAM

WF1 WF2

Power Supply Block Diagram

E57A0BLP1-6-7 1-6-8

IC1006(SHUNT REGULATOR)

REG

NOTE : The voltage for parts in hot circuit is measured usinghot GND as a common terminal.

AC1001AC CORD F1001

LINEFILTER

L1001D1001, D1002D1004, D1005

Q1003 Q1001

2

4

7

3

4

IC1001ERRORVOLTAGE DET

T1001

11

12

13

15

14

16

17

18

SWITCHINGSWITCHINGCONTROL

1

2

6

BRIDGERECTIFIER

HOT

AV CBA

HOT CIRCUIT. BE CAREFUL.

D1003

RECTIFIER

D1030

RECTIFIER

D1016

RECTIFIER

Q1016

Q1006

Q1005

Q1011

Q1015

Q1002

CN1001

Q1004

-FL

EV+5V

F2F1

P-ON+12VEV+3.3V

P-ON+5VP-ON+3.3V

FROM/TOCN401

1,2,3 EV+1.5V4,5 EV+3.3V

14,15 EV+9V13 P-ON+5V17 P-ON+3.3V19 PWRCON

+1.5VREG.

IC1002

CAUTION !Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.If Main Fuse (F1001) is blown, check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

Q1008

LATCH

D1006SCHOTTKYBARRIER

SCHOTTKYBARRIER

D1008

CAUTIONFOR CONTINUED PROTECTION AGAINST FIRE HAZARD,REPLACE ONLY WITH THE SAME TYPE FUSE.

T1.6A L 250V

Q1050

1-7-1 E57A0SC

SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS

Standard Notes

WARNINGMany electrical and mechanical parts in this chassishave special characteristics. These characteristicsoften pass unnoticed and the protection afforded bythem cannot necessarily be obtained by using replace-ment components rated for higher voltage, wattage,etc. Replacement parts that have these special safetycharacteristics are identified in this manual and itssupplements; electrical components having such fea-tures are identified by the mark " ! " in the schematicdiagram and the parts list. Before replacing any ofthese components, read the parts list in this manualcarefully. The use of substitute replacement parts thatdo not have the same safety characteristics as speci-fied in the parts list may create shock, fire, or otherhazards.

Notes:1. Do not use the part number shown on these draw-

ings for ordering. The correct part number is shownin the parts list, and may be slightly different oramended since these drawings were prepared.

2. All resistance values are indicated in ohms

(K=103, M=106).

3. Resistor wattages are 1/4W or 1/6W unless other-wise specified.

4. All capacitance values are indicated in µF

(P=10-6 µF).

5. All voltages are DC voltages unless otherwisespecified.

6. Electrical parts such as capacitors, connectors,diodes, IC’s, transistors, resistors, switches, andfuses are identified by four digits. The first two dig-its are not shown for each component. In eachblock of the diagram, there is a note such as shownbelow to indicate these abbreviated two digits.

1-7-2 E57A0SC

LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWINGPAGES:

1. CAUTION:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE.

2. CAUTION:Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not defec-tive before you connect the AC plug to the AC power supply. Otherwise it may cause some components in thepower supply circuit to fail.

3. Note:(1) Do not use the part number shown on the drawings for ordering. The correct part number is shown in the parts

list, and may be slightly different or amended since the drawings were prepared.(2) To maintain original function and reliability of repaired units, use only original replacement parts which are listed

with their part numbers in the parts list section of the service manual.

4. Wire Connectors(1) Prefix symbol "CN" means "connector" (can disconnect and reconnect).(2) Prefix symbol "CL" means "wire-solder holes of the PCB" (wire is soldered directly).

5. Voltage indications for PLAY modes on the schematics are as shown below:

6. How to read converged lines

7. Test Point Information

2 31 5.0(2.5)

5.0

The same voltage for both PLAY & STOP modes

Indicates that the voltage is not consistent here.

PLAY modeSTOP mode

(Unit: Volt)

1-D3

Distinction Area Line Number

(1 to 3 digits)

Examples:

1. "1-D3" means that line number "1" goes to area "D3". 2. "1-B1" means that line number "1" goes to area "B1".

3

2

1

A B C D

1-B1

1-D3

AREA D3

AREA B1

: Indicates a test point with a jumper wire across a hole in the PCB.

: Used to indicate a test point with a component lead on foil side.

: Used to indicate a test point with no test pin.

: Used to indicate a test point with a test pin.

DVD Main 1/3 Schematic Diagram

1-7-3 1-7-4 E57A0SCD1


1-7-5 1-7-6 E57A0SCD2

1-7-7 1-7-8

IC101 VOLTAGE CHARTPIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP

1 3.3 3.3 33 2.2 2.9 65 0.1 0.1 97 3.4 3.4

2 ~ ~ 34 ~ ~ 66 1.2 2.5 98 1.6 1.6

3 ~ ~ 35 ~ ~ 67 1.6 1.6 99 0 0

4 0 0 36 ~ ~ 68 3.4 3.4 100 ----- -----

5 ~ ~ 37 ~ ~ 69 0 0 101 ----- -----

6 ~ ~ 38 0.3 0.5 70 1.7 1.7 102 ----- -----

7 3.3 3.3 39 0.1 0.1 71 2.4 1.7 103 ----- -----

8 ~ ~ 40 ~ ~ 72 ----- ----- 104 3.3 3.3

9 ~ ~ 41 ~ ~ 73 ----- ----- 105 0.9 0.9

10 ~ ~ 42 3.3 3.3 74 ----- ----- 106 0 0

11 0 0 43 0 0 75 3.4 3.4 107 0.8 0.8

12 ~ ~ 44 ~ ~ 76 ----- ----- 108 1.6 1.6

13 ~ ~ 45 ~ ~ 77 ----- ----- 109 2.1 2.1

14 3.3 3.3 46 2.0 2.6 78 0.1 0.1 110 2.6 2.6

15 1.5 1.5 47 ----- ----- 79 3.3 3.3 111 2.0 2.0

16 0 0 48 ----- ----- 80 0 0 112 0.7 0.9

17 3.4 3.4 49 ----- ----- 81 ----- ----- 113 2.1 2.1

18 3.4 3.4 50 3.4 3.4 82 ----- ----- 114 1.8 1.8

19 ~ ~ 51 3.4 3.4 83 ----- ----- 115 1.4 1.4

20 ~ ~ 52 ----- ----- 84 ----- ----- 116 0.3 0.3

21 ~ ~ 53 3.4 3.4 85 ----- ----- 117 1.6 1.6

22 ~ ~ 54 3.4 3.4 86 ----- ----- 118 3.3 3.3

23 3.3 3.3 55 3.3 3.3 87 ----- ----- 119 0 0

24 0 0 56 3.3 3.3 88 ----- ----- 120 1.9 1.9

25 0.4 0.4 57 0 0 89 ----- ----- 121 1.9 1.9

26 0.9 0.6 58 0 0 90 ----- ----- 122 2.4 2.4

27 ~ ~ 59 3.3 3.3 91 3.3 3.3 123 2.4 2.4

28 ~ ~ 60 3.4 3.4 92 1.7 1.5 124 2.4 2.4

29 3.3 3.3 61 3.1 3.1 93 0 0 125 2.4 2.4

30 0 0 62 ----- ----- 94 ----- ----- 126 2.0 2.0

31 ~ ~ 63 3.4 3.4 95 3.4 0.1 127 2.0 2.0

32 ~ ~ 64 0.8 0.8 96 3.4 3.4 128 2.0 2.0

PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP

129 2.0 2.0 161 0.5 0.5 193 ~ ~ 225 1.9 1.9

130 2.2 2.2 162 1.4 1.4 194 0 0 226 3.3 3.3

131 2.3 2.3 163 ----- ----- 195 3.3 3.3 227 ~ ~

132 0.4 0.1 164 0.9 0.9 196 ~ ~ 228 ~ ~

133 1.2 0.4 165 3.3 3.3 197 ~ ~ 229 ~ ~

134 0.4 0.1 166 1.5 1.5 198 0 0 230 0 0

135 0.2 0.2 167 0 0 199 ~ ~ 231 ----- -----

136 2.3 2.3 168 2.1 2.1 200 ~ ~ 232 3.3 3.3

137 1.7 1.7 169 0 0 201 ~ ~ 233 3.3 3.3

138 0 0 170 0.8 0.8 202 3.3 3.3 234 1.6 1.6

139 1.7 1.7 171 3.3 3.3 203 ~ ~ 235 ~ ~

140 1.7 1.7 172 1.6 1.6 204 ~ ~ 236 0 0

141 1.7 1.7 173 ----- ----- 205 ~ ~ 237 1.7 1.7

142 1.7 1.7 174 1.8 1.8 206 0 0 238 3.0 3.0

143 0.5 0.5 175 1.7 1.7 207 2.4 3.5 239 3.3 3.3

144 1.6 1.6 176 1.4 0.1 208 2.4 2.1 240 3.3 3.3

145 3.3 3.3 177 0 0 209 3.3 3.3 241 0 0

146 1.8 1.8 178 ----- ----- 210 ~ ~ 242 3.2 3.2

147 ----- ----- 179 ----- ----- 211 0 0 243 2.4 2.1

148 ----- ----- 180 ----- ----- 212 ~ ~ 244 1.5 1.5

149 3.3 3.3 181 1.7 1.7 213 1.5 1.5 245 0 0

150 1.7 1.7 182 3.3 3.3 214 ~ ~ 246 2.4 2.1

151 0 0 183 0 0 215 0 0 247 ~ ~

152 1.7 1.7 184 ~ ~ 216 ~ ~ 248 0 0

153 3.3 3.3 185 ~ ~ 217 ~ ~ 249 ~ ~

154 1.4 1.4 186 1.5 1.5 218 3.3 3.3 250 3.3 3.3

155 0 0 187 ~ ~ 219 ~ ~ 251 ~ ~

156 2.2 2.2 188 ~ ~ 220 ~ ~ 252 ~ ~

157 3.3 3.3 189 3.3 3.3 221 0 0 253 ~ ~

158 0.7 0.7 190 ~ ~ 222 1.5 1.5 254 0 0

159 0 0 191 ~ ~ 223 1.9 1.9 255 ~ ~

160 0.5 0.5 192 ~ ~ 224 0 0 256 ~ ~


1-7-9 1-7-10 E57A0SCD3

AV 1/3 Schematic Diagram

1-7-11 1-7-12 E57A0SCAV1

NOTE :The voltage for parts in hot circuit is measuredusing hot GND as a common terminal.

CAUTION !Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.If Main Fuse (F1001) is blown, check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.

CAUTION

FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,

REPLACE ONLY WITH THE SAME TYPE FUSE.

AV 2/3 Schematic Diagram

1-7-13 1-7-14 E57A0SCAV2

AV 3/3 & Function Schematic Diagram

7G 5G 3G 1G4G6G 2G

a

d

g

c b

ef

1

3

2

4

5

DVDVCDPBC

STANDBY

A-BREPEAT

TRK.CHP.TITLE

7G 6G 5G 4G 3G 2G 1G

a

b

c

d

e

f

g

c

d

e

f

g

c

d

e

f

g

c

d

e

f

g

c

d

e

f

g

c

d

e

f

g

h

i

a

b

a

b

a

b

a

b

a

b

FL2001 MATRIX CHART

STANDBY

TITLE CHP. TRK. CDV

PBCDVD

REPEAT

A-B

1

3

2

4

5

1-7-15 1-7-16 E57A0SCAV3

1-7-17 1-7-18

AV CBA Top View

BE57A0F01012



CAUTION



WF3PIN 31 OFIC1401

WF2PIN 9 OFCN1601

WF1PIN 1 OFCN1601

WF4PIN 13 OFCN1601

WF5PIN 15 OFCN1601

WF6PIN 18 OFCN1601

1-7-19

AV CBA Bottom View

BE57A0F010121-7-20



CAUTION



1-8-2 E57A0WF1-8-1

NOTE:Input CD: 1kHz PLAY (WF4~WF6) DVD: POWER ON (STOP) MODE (WF1~WF3)

WAVEFORMS

WF6

SPDIF

Pin 18 of CN1601

1V 0.1µsec

WF1 Pin 1 of CN1601

WF3 Pin 31 of IC1401

WF4

AUDIO-L

Pin 13 of CN1601

1V 0.5msec

WF5

AUDIO-R

Pin 15 of CN1601

1V 0.5msec

WF2 Pin 9 of CN1601

VIDEO-Y 0.2V 20µsec

VIDEO-C 0.2V 20µsec

VIDEO-CVBS 0.5V 20µsec

1-9-1 1-9-2

WIRING DIAGRAM

E57A0WI

DVD MECHA

DVD MAIN CBA UNIT

PICK UP UNIT

CN201CN301

1 2 3 4T

RAY

-OU

TT

RAY

-IN

GN

D

5 6

SP

(-)

7

SP

(+)

8S

L(-)

9S

L(+)

FG

-IN

P-O

N+3

.3V

(D)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

TRAY-IN

AV CBA(BE57A0F01012)

EV

+1.5

V1

1E

V+1

.5V

22

EV

+3.3

V4

4E

V+3

.3V

55

GN

D6

6G

ND

77

GN

D8

8G

ND

99

GN

D10

10G

ND

1111

GN

D12

12P

-ON

+5V

1313

EV

+9V

1414

EV

+9V

1515

FP

-ST

B16

16P

-ON

+3.3

V17

17F

P-D

IN18

18P

WR

CO

N19

19F

P-D

OU

T20

20F

P-C

LK21

21R

EM

OT

E22

22

CN401

CN1001

VID

EO

-R3

3G

ND

44

VID

EO

-Y1

1A

SP

EC

T2

2

VID

EO

-B5

5

A-M

UT

E12

12G

ND

1111

GN

D6

6V

IDE

O-G

77

GN

D8

8V

IDE

O-C

99

GN

D10

10

CN601

CN1601

AC CORDAUDIO-LOUT

AUDIO-ROUT

VIDEOOUT

DIGITALAUDIO OUT

S-VIDEO OUT

EV

+1.5

V3

3

DRIVE CBA

19 20

SP

DIF

1818

AU

DIO

-L13

13A

-L-M

UT

E14

14A

UD

IO-R

1515

A-R

-MU

TE

1616

AU

DIO

+5V

1717

GN

D

VR

EF

P-O

N+5

V

FE CB D A PD

-MO

NI

DV

D-L

D

GN

D(L

D)

GN

D(D

VD

-PD

)

TS

(+)

FS

(-)

FS

(+)

TS

(-)

GN

D(C

D-P

D)

CD

-LD

CD

/DV

D

FS

TS

DETECTOR

11 2 3 5 6 4 7

FG CBA

FGSENSOR

TRAY-OUT

M

SLEDMOTOR

M

SPINDLEMOTOR

W10

01

W16

01

OPTICALAUDIO OUT

SCART JACK

12

34

56

78

910

1112

1314

1516

1718

1920

21

CN204

1AN

ALOG

-MON

ITOR

2G

ND

(NO CONNECTION)

1-10-1 E57A0TEST

FIRMWARE RENEWAL MODE1. Turn the power on and remove the disc on the tray.2. To put the DVD player into version up mode, press

[9], [8], [7], [6], and [SEARCH MODE] buttons onthe remote control unit in that order. The tray willopen automatically.Fig. a appears on the screen and Fig. b appears onthe VFD.

The DVD player can also enter the version upmode with the tray open. In this case, Fig. a will beshown on the screen while the tray is open.

3. Load the disc for version up.4. The DVD player enters the F/W version up mode

automatically. Fig. c appears on the screen andFig. d appears on the VFD.

The appearance shown in (*2) of Fig. c isdescribed as follows:

5. After programming is finished, the tray opens auto-matically. Fig. e appears on the screen and thechecksum in (*3) of Fig. e appears on the VFD.(Fig. f)

At this time, no buttons are available.6. Unplug the AC cord from the AC outlet. Then plug it

again.7. Turn the power on by pressing the power button

and the tray will close.8. Press [1], [2], [3], [4], and [DISPLAY] buttons on the

remote control unit in that order. Fig. g appears on the screen.

9. Press [3] button on the remote control unit. Fig. h appears on the screen.

10.To finish this mode, press [POWER] button.

F/W Version Up Mode

Please insert a DISCfor F/W Version Up.

EXIT: POWER

Fig. a Version Up Mode Screen

Fig. b VFD in Version Up Mode

Fig. c Programming Mode Screen

F/W Version Up Mode

VERSION : ******** Reading...(*2)

EXIT: POWER

Fig. d VFD in Programming Mode (Example)

AppearanceNo. State

Reading... Sending files into the memory

Erasing... Erasing previous version data

Programming...

1

2

3 Writing new version data

Fig. e Completed Program Mode Screen

F/W Version Up Mode

VERSION : ********CompletedSUM : 7abc (*3)

Fig. f VFD upon Finishing the Programming Mode (Example)

Fig. g

model: ****** Ver: **** Region: **

1: VFD TEST2: TT REPEAT PLAY3: EEPROM CLEAR4: MEASUREMENT SERVO5: DISC READ CHECK6: MECHA CHECK7: DISC INFO8: ERROR RATE

EXIT: POWERRETURN: -----

Fig. h

model: ****** Ver: **** Region: **

TEST 3: EEPROM CLEAREEPROM CLEAR: OK

EXIT: POWERRETURN: -----

1-11-1 E57A0TI

Tray Close ~ Play / Play ~ Tray Open

Tray IN(TL221)

3.3V

0V

0V

3.3V

0V

1.65V

0V

0V

0V

1.65V

1.65V

1.65V

Tray OUT(TL220)

Sled Drive(TP303)

Disc Drive(TP301)

Focus Drive(TP304)

Tracking Drive(TP302)

TrayClose

DiscRotation Play

DiscStop

TrayOpen

SYSTEM CONTROL TIMING CHARTS

1-12-1 E57A0PIN

IC PIN FUNCTION DESCRIPTIONS

IC2001 [ PT6313-S-TP ]

Pin No.

In/OutSignal Name

Name Function

1 In FP-CLK Clock Input

2 In FP-STB Serial Interface Strobe

3 In K1 Key Data 1 Input

4 In K2 Key Data 2 Input

5 - VSS GND

6 - VDD Power Supply

7 Out a / KEY-1 Segment Output / Key Source-1

8 Out b / Key-2 Segment Output / Key Source-2

9 Out c / Key-3 Segment Output / Key Source-3

10 Out d / Key-4 Segment Output/ Key Source-4

11 Out e

Segment Output 12 In f

13 In g

14 Out h

15 - VEE Pull Down Level

16 Out i Segment Output

17

Out

7G

Grid Output

18 6G

19 5G

20 4G

21 3G

22 2G

23 1G

24 - VDD Power Supply

25 - VSS GND

26 In OSC Oscillator Input

27 Out FP-DOUT Serial Data Output

28 In FP-DIN Serial Data Input

1-13-1 E57A0LE

1 4

8 5

NJM4558DKIA4558P

28 15

14

PT6313-S-TP

1

E C B

2SA1015-Y (TPE2)KTA1266 (GR,Y)KTC3198 (Y)2SC2120-Y(TPE2)KTC3205 (Y)2SC2236-Y-TPE6,C

E C B

2SC2785 (H,F)KTC3199 (GR)KRA110MKTA1267 (Y)BN1L3Z (P)

A

K

C

E

LTV-817(B,C)-F

KIA431-AT

G D S

2SK3566

PQ070XF01SZ K A R

1 2 3 4

Note:A: AnodeK: CathodeE: EmitterC: CollectorB: BaseR: ReferenceG: GateD: DrainS: Source

1: Vin2: Vo3: GND4: Vc

34 18

17

MM1567AJ

1

0C-0805T*002GP1FA513TZ

1 2 3

LEAD IDENTIFICATIONS

1-14-1 E57A0EX

A15

A1X

DVD Main CBA Unit

2L011

2L011

2L011

A16

See Electrical Parts Listfor parts with this mark.

Some Ref. Numbers are not in sequence.

AV CBA

2B3 2L031

2L105

2L101

F1001

W1601

W1001 2L031

1B1

2L021

A22L021

2L021

A13

A13

A26

2B24

A17

2L031

2L041

2L071

2L071

2L071

JK1201JK1202

JK1402

JK1401

JK1404

IC1204

AC1001

EXPLODED VIEWS

Cabinet

1-14-2 E57A0EX

X10 X5 X2

X4

S2

S2

S4

Unit

S1

X1X12

S9

Packing

20030210 1-15-1 E57A0CA

MECHANICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a !have special characteristics important to safety. Beforereplacing any of these components, read carefully theproduct safety notice in this service manual. Don'tdegrade the safety of the product through improper ser-vicing.

NOTE: Parts that are not assigned part numbers (---------) arenot available.

Ref. No. Description Part No.

A1X FRONT ASSEMBLY E57A0ED 0VM204062

A2 TRAY PANEL E5702CD 0VM414662

A13 FOOT E5630UD 0VM414074

A15 MAIN CHASSIS E5700UD 0VM101167

A16 TOP COVER:SILVER E56A0UD 0VM305312C

A17 REAR PANEL E57A0ED 0VM203938

A26 LABEL, SERIAL BAR CODE E57A0ED ----------

1B1 DVD MECHA 0838 VCDVM040 N79F0GVM

2B3 HOLDER, MAIN PCB E5700UD 0VM305832B

2B24 CUSHION, SHIELD E5700UD 0VM414640

2L011 SCREW, C-TIGHT M3X5 BIND HEAD + GBCC3050

2L021 SCREW, S-TIGHT M3X10 BIND HEAD+ GBMS3100

2L031 SCREW, C-TIGHT M3X6 BIND HEAD GBMC3060

2L041 SCREW, B-TIGHT M3X8 BIND HEAD + GBKB3080



2L105 P-TIGHT SCREW 3X8 BIND + GBMP3080

PACKING

S1 GIFT BOX CARTON E57A0ED 0VM306104

S2 STYROFOAM E5700UD 0VM101200

S4 UNIT, BAG E5500UD 0VM411683

S9 LABEL, SERIAL NO. HE240ED or ----------

LABEL, SERIAL NO. E57A0ED ----------

ACCESSORIES

X1 REMOTE CONTROL UNIT DVD 0842 VCDVR040 or NA601ED

REMOTE CONTROL UNIT DVD 0842 VCDVR040 NA651ED

X2 DRY BATTERY R6P/2S or XB0M451T0001

DRY BATTERY ES-GR6M-C XB0M571GLP01

X4 ACCESSORY BAG K8092BA 0VM404632

X5 AV CORD TSCKA-Y/RW100 or WPZ0102TM015

AV CORD RCA(M*2)TO RCA(M*2) WPZ0102LTE01

X10! OWNER'S MANUAL E57A0ED 0VMN03471

X12 SERVICE CENTER LIST HC2C0ED 0VMN03071

20030210 1-16-1 E57A0EL

ELECTRICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a !have special characteristics important to safety. Beforereplacing any of these components, read carefully theproduct safety notice in this service manual. Don'tdegrade the safety of the product through improper ser-vicing.

NOTES: 1. Parts that are not assigned part numbers (---------)

are not available.2. Tolerance of Capacitors and Resistors are noted

with the following symbols.

DVD MAIN CBA UNIT

AV CBA

C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%


DVD MAIN CBA UNIT N79G0GEP


AV CBA Consists of the followings

0VSA13753

CAPACITORSC1001! METALLIZED FILM CAP. 0.047µF/250V K or CT2E473DC011

! METALLIZED FILM CAP. 0.047µF/250V M CT2E473MS037

C1003 CERAMIC CAP. B K 0.01µF/500V CCD2JKP0B103

C1004 ELECTROLYTIC CAP. 33µF/400V M(L•Z) or CA2H330NC010

ELECTROLYTIC CAP. 33µF/400V M(105°C) CE2HMZNTH330

C1005 CERAMIC CAP. SL K 56pF/1KV CCD3AKPSL560

C1006! SAFETY CAP. 2200pF/250V or CCN2EMP0E222

! SAFETY CAP. 2200pF/250V CA2E222MR049

C1007 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102

C1010 CERAMIC CAP.(AX) CH J 560pF/50V CA1J561TU008

C1013 CERAMIC CAP.(AX) B K 3300pF/50V CA1J332TU011



C1021 CHIP CERAMIC CAP. B K 0.01µF/50V CHD1JK30B103


C1029 CERAMIC CAP.(AX) X K 5600pF/16V CCA1CKT0X562

C1032 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100

C1033 FILM CAP.(P) 0.022µF/50V J or CMA1JJS00223

FILM CAP.(P) 0.022µF/50V J CA1J223MS029




C1037 CHIP CERAMIC CAP. F Z 0.1µF/50V CHD1JZ30F104



C1047 FILM CAP.(P) 0.01µF/50V J or CMA1JJS00103

FILM CAP.(P) 0.01µF/50V J CA1J103MS029







C1205 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221












C1351 CHIP CERAMIC CAP. B K 0.1µF/25V CHD1EK30B104

C1353 CHIP CERAMIC CAP. B K 1µF/10V CHD1AK30B105


C1355 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000

C1358 CHIP CERAMIC CAP. CH D 9pF/50V CHD1JD3CH9R0






C1422 CHIP CERAMIC CAP. B K 0.1µF/25V CHD1EK30B104

C1441 CHIP CERAMIC CAP. B K 0.33µF/10V CHD1AK30B334


C1461 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL010















C1534 CHIP CERAMIC CAP. B K 1000pF/50V CHD1JK30B102








CONNECTORSCN1001 FMN CONNECTOR, TOP 22P 22FMN-BTK or JCFNG22JG001

FFC/FPC CONNECTOR 22P 00 6232 022 000 800 JC62G22TM009

CN1601 FMN CONNECTOR, TOP 18P 18FMN-BTK or JCFNG18JG001

FFC/FPC CONNECTOR 18P 00 6232 018 000 800 JC62G18TM009


20030210 1-16-2 E57A0EL

DIODESD1001 RECTIFIER DIODE 1N4005 NDQZ001N4005

D1002 RECTIFIER DIODE 1N4005 NDQZ001N4005

D1003 RECTIFIER DIODE BA157 or NDQZ000BA157

FAST RECOVERY DIODE ERA18-04 QDPZ0ERA1804



D1006 SCHOTTKY BARRIER DIODE SB140 or NDQZ000SB140

SCHOTTKY BARRIER DIODE ERA81-004 QDPZERA81004

D1008 SCHOTTKY BARRIER DIODE SB140 or NDQZ000SB140

SCHOTTKY BARRIER DIODE ERA81-004 QDPZERA81004



D1012 SWITCHING DIODE 1N4148M or NDTZ01N4148M

SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

D1015 ZENER DIODE DZ-6.8BSBT265 or NDTB0DZ6R8BS

ZENER DIODE MTZJT-776.8B QDTB0MTZJ6R8



D1017 ZENER DIODE DZ-22BSBT265 or NDTB00DZ22BS

ZENER DIODE MTZJT-7722B QDTB00MTZJ22









D1030 RECTIFIER DIODE FR202 or NDQZ000FR202

FAST RECOVERY DIODE ERB32-01L3 QDQZ0ERB3201

D1046 ZENER DIODE DZ-5.6BSCT265 or NDTC0DZ5R6BS

ZENER DIODE MTZJT-775.6C QDTC0MTZJ5R6



D1048 ZENER DIODE DZ-15BSAT265 or NDTA00DZ15BS

ZENER DIODE MTZJT-7715A QDTA00MTZJ15



D1053 PCB JUMPER D0.6-P10.0 JW10.0T











































ICSIC1001! PHOTOCOUPLER LTV-817B-F or NPEB0LTV817F

! PHOTOCOUPLER LTV-817C-F NPEC0LTV817F

IC1002 VOLTAGE REGULATOR PQ070XF01SZ QSZBA0SSH026

IC1006 IC KIA431-AT NSZLA0TJY001

IC1201 IC:OP AMP KIA4558P or NSZBA0SJY004

IC:OP AMP NJM4558D QSZBA0SJR006

IC1204 FIBER OPTIC TRANS.MODULE 0C-0805T*002 or JWHHA00JD002

FIBER OPTIC TRANS.MODULE GP1FA513TZ JWHHA00SH005

IC1401 DRIVER FOR DVD(6CH) MM1567AJ QSZBA0SMM084

IC2001 FL DRIVER IC PT6313-S-TP NSZBA0TG2006

COILSL1001! LINE FILTER 50MH LF-4Z-E503 or LLBG00ZKQ008

! LINE FILTER 50MH LF-4D-E503 or LLBG00ZKQ009

! LINE FILTER 56MH TLF14CB5630R2 LLBG00ZTU022

L1007 CHOKE COIL 22µH-K LLBD00PKV006



L1011 BEAD CORE B16 RH 3.5X3X1.3 XL03003XM002

L1043 BEAD CORE B16 RH 4X3X2 XL03003XM001

L1060 BEAD CORE B16 RH 3.5X3X1.3 XL03003XM002

L1350 INDUCTOR 100µH-K-26T LLAXKATTU101

L1351 INDUCTOR 0.47µH-K-26T LLAXKATTUR47

L1401 CHIP BEAD MMZ1608Y121CT XL06001TE004








L2001 PCB JUMPER D0.6-P5.0 JW5.0T

L2002 INDUCTOR 100µH-K-26T LLAXKATTU101

L2003 PCB JUMPER D0.6-P5.0 JW5.0T

L1522A CHIP BEAD MMZ1608R102CT XL06001TE002

TRANSISTORSQ1001 FET 2SK3566 QFWZ02SK3566

Q1002 TRANSISTOR KTA1267(Y) NQSY0KTA1267

Q1003 TRANSISTOR KTC3199(GR) or NQS10KTC3199


20030210 1-16-3 E57A0EL

TRANSISTOR 2SC2785(H) QQSH02SC2785

Q1004 TRANSISTOR KTC3198(Y) NQSY0KTC3198

Q1005 TRANSISTOR KTC3198(Y) NQSY0KTC3198

Q1006 RES. BUILT-IN TRANSISTOR KRA110M or NQSZ0KRA110M

RES. BUILT-IN TRANSISTOR BN1L3Z(P) QQSP00BN1L3Z



Q1011 TRANSISTOR 2SC2120-Y(TPE2) QQSY02SC2120

Q1015 RES. BUILT-IN TRANSISTOR KRA110M or NQSZ0KRA110M

RES. BUILT-IN TRANSISTOR BN1L3Z(P) QQSP00BN1L3Z



Q1050 TRANSISTOR KTC3205(Y) or NQSY0KTC3205

TRANSISTOR 2SC2236-Y-TPE6,C QQSY02SC2236





Q1203 TRANSISTOR KTA1266(Y) or NQSY0KTA1266

TRANSISTOR 2SA1015-Y(TPE2) QQSY02SA1015





Q1352 TRANSISTOR 2SC2785(F) QQSF02SC2785

Q1521 TRANSISTOR 2SC2785(F) QQSF02SC2785



RESISTORSR1002 CHIP RES.(1608) 1/10W J 1k Ω RRXAJR5Z0102

R1004 METAL OXIDE FILM RES. 1W J 150k Ω or RN01154ZU001

METAL OXIDE FILM RES. 1W J 150k Ω RN01154KE009

R1005 CARBON RES. 1/4W J 1.5M Ω RCX4JATZ0155

R1006 CARBON RES. 1/4W J 1.5M Ω RCX4JATZ0155

R1008 CARBON RES. 1/4W J 560 Ω RCX4JATZ0561

R1010 CARBON RES. 1/6W J 3.9k Ω or RCX6JATZ0392

CARBON RES. 1/4W J 3.9k Ω RCX4JATZ0392

R1011 METAL OXIDE FILM RES. 1W J 2.2 Ω or RN012R2ZU001

METAL OXIDE FILM RES. 1W J 2.2 Ω RN012R2KE009


R1019 CHIP RES.(1608) 1/16W F 820 Ω or RRXGFR5Z0821

CHIP RES. 1/10W F 820 Ω RRXAFR5Z8200

R1020 CHIP RES.(1608) 1/10W J 470 Ω RRXAJR5Z0471

R1021 CHIP RES.(1608) 1/10W J 1k Ω RRXAJR5Z0102


R1023 CHIP RES.(1608) 1/16W F 2.4k Ω or RRXGFR5Z0242

CHIP RES.(1608) 1/10W F 2.4k Ω RRXAFR5Z2401


R1029 CARBON RES. 1/6W J 100k Ω or RCX6JATZ0104

CARBON RES. 1/4W J 100k Ω RCX4JATZ0104

R1032 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
















R1069 CARBON RES. 1/6W J 470 Ω or RCX6JATZ0471

CARBON RES. 1/4W J 470 Ω RCX4JATZ0471

R1073 METAL OXIDE FILM RES. 2W J 10 Ω or RN02100ZU001

METAL OXIDE FILM RES. 2W J 10 Ω RN02100KE009

R1074 RECTIFIER DIODE 1N4005 NDQZ001N4005

R1075 CHIP RES.(1608) 1/10W J 2.7k Ω RRXAJR5Z0272


R1078 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000

R1079 PCB JUMPER D0.6-P5.0 JW5.0T


R1081 CHIP REG. 1/16W F 100 Ω or RRXGFR5Z0101

CHIP RES. 1/10W F 100 Ω RRXAFR5Z1000















R1205 CHIP RES.(1608) 1/16W F 20k Ω or RRXGFR5Z0203

CHIP RES.(1608) 1/10W F 20k Ω RRXAFR5Z2002

R1206 CHIP RES.(1608) 1/16W F 20k Ω or RRXGFR5Z0203




R1209 CHIP RES. 1/16W F 30k Ω or RRXGFR5Z0303


R1210 CHIP RES. 1/16W F 30k Ω or RRXGFR5Z0303























20030210 1-16-4 E57A0EL















R1421 CHIP RES. 1/16W F 75 Ω or RRXGFR5Z0750

CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5Z75R0


R1441 CHIP RES. 1/16W F 75 Ω or RRXGFR5Z0750



R1461 CHIP RES(1608) 1/16W F 36 Ω or RRXGFR5Z0360














R1530 CHIP BEAD MMZ1608Y121CT XL06001TE004

R1531 CHIP BEAD MMZ1608Y121CT XL06001TE004

R1532 CHIP INDUCTOR BK1608HS121-T LLC121NTU017

























SWITCHESSW2002 TACT SWITCH KSM0614B or SST0101HH013

TACT SWITCH SKQSAF001A SST0101AL041

SW2003 TACT SWITCH KSM0614B or SST0101HH013












MISCELLANEOUSAC1001! AC CORD PE8B2CB980A-057 WAE0172LW006

F1001! FUSE T1.6AL/250V or PAGC20BW3162

! FUSE T1.6AL/250V or 1790994

! FUSE 50T016H 1.6A/250V PAGH20BHV162

FH1001 FUSE HOLDER MSF-015 XH01Z00LY001

FH1002 FUSE HOLDER MSF-015 XH01Z00LY001

FL2001 V.F.D. 7-BT-292GN TVFD150FT010

J2576 CERAMIC CAP.(AX) B K 1000pF/50V CCA1JKT0B102

JK1201 2PIN JACK MSD-242V-01 NI JXRL020LY067

JK1202 RCA JACK(BLACK) MSP-251V-01 NI JXRL010LY070

JK1401 S TYPE JACK MDC-050V-2.4 JXEL040LY001

JK1402 RCA JACK(YELLOW) MSP-251V-02 PBSN JXRL010LY017

JK1404 21P RGB JACK AJ-2050*040 JXGL210JD002

RM2001 REMOTE RECEIVER PIC-37042LU USESJRSKK033

SA1001! SURGE ABSORBER PVR-10D471KB or NVQZ10D471KB

! SURGE ABSORBER CNR-10D471K NVQZR10D471K

T1001! POWER TRANSFORMER CSA-SW0215C LTT00EPSA141

W1001 22P FFC AV PCB TO MAIN WX1E5700-003

W1601 18P FFC WX1E5700-002


DV

P-4000

E57A

0ED

DVP-4000 Service Manual

Documents

Transcript of DVP-4000 Service Manual