DS307 PIR Intrusion Detector
4
Intrusion Alarm Systems | DS307 PIR Intrusion Detector DS307 PIR Intrusion Detector www.boschsecurity.com u Motion Analyzer II processing u PIR supervision u Motion Monitor supervision u LED indicator u Three sensitivity settings The DS307 PIR Intrusion Detector uses Motion Analyzer II signal processing to reduce false alarms. The detector’s internally pointable mirrors, three coverage patterns, and four wall mounting options provide installation flexibility. Functions Motion Analyzer II Processing Motion Analyzer II uses multiple thresholds and timing windows to analyze timing, amplitude, duration, and polarity of signals to make an alarm decision. It tolerates extreme levels of heat and light disturbances caused by heaters and air conditioners, hot and cold drafts, sunlight, lightning, and moving headlights. PIR Supervision PIR operation is checked electronically approximately every 12 hours. If the circuit fails, the LED pulses four times and the trouble output activates. Motion Monitor Supervision Confirms the detector has a clear view of the detection area. A trouble condition is indicated if the detector has not alarmed at least once during a selected time period. LED Indicator LED flashes to indicate trouble condition. Internal Noise Voltage Test Pins provide precise pattern location and background disturbance evaluation using a standard analog meter. Three Sensitivity Settings • Standard Sensitivity: Recommended setting for maximum false alarm immunity. Tolerates environmental extremes on this setting. Not recommended for long range or barrier coverage patterns. • Intermediate Sensitivity: Recommended setting for any location where an intruder is expected to cover only a small portion of the protected area. Tolerates normal environments on this setting. • High Sensitivity: Fast response to intruder signals. For use in quiet environments where fluctuations in heat or light are not anticipated.
Transcript of DS307 PIR Intrusion Detector
Intrusion Alarm Systems | DS307 PIR Intrusion Detector
DS307 PIR Intrusion Detector
www.boschsecurity.com
u Motion Analyzer II processing
u PIR supervision
u Motion Monitor supervision
u LED indicator
u Three sensitivity settings
The DS307 PIR Intrusion Detector uses MotionAnalyzer II signal processing to reduce false alarms.The detector’s internally pointable mirrors, threecoverage patterns, and four wall mounting optionsprovide installation flexibility.
Functions
Motion Analyzer II ProcessingMotion Analyzer II uses multiple thresholds and timingwindows to analyze timing, amplitude, duration, andpolarity of signals to make an alarm decision. Ittolerates extreme levels of heat and light disturbancescaused by heaters and air conditioners, hot and colddrafts, sunlight, lightning, and moving headlights.
PIR SupervisionPIR operation is checked electronically approximatelyevery 12 hours. If the circuit fails, the LED pulses fourtimes and the trouble output activates.
Motion Monitor SupervisionConfirms the detector has a clear view of thedetection area. A trouble condition is indicated if thedetector has not alarmed at least once during aselected time period.
LED IndicatorLED flashes to indicate trouble condition. InternalNoise Voltage Test Pins provide precise patternlocation and background disturbance evaluation usinga standard analog meter.
Three Sensitivity Settings• Standard Sensitivity: Recommended setting for
maximum false alarm immunity. Toleratesenvironmental extremes on this setting. Notrecommended for long range or barrier coveragepatterns.
• Intermediate Sensitivity: Recommended setting forany location where an intruder is expected to coveronly a small portion of the protected area. Toleratesnormal environments on this setting.
• High Sensitivity: Fast response to intruder signals. Foruse in quiet environments where fluctuations in heator light are not anticipated.
Certifications and approvals
Region Certification
Europe CE 2004/108/EC, EN55022: 2006,EN50130-4: 1996 +A1: 1998 +A2:2003, EN61000-4-2: 1995 +A1: 1999+A2: 2001, EN61000-4-3: 2006,EN61000-4-4: 2004, EN61000-4-5:2005, EN61000-4-6: 2007,EN61000-4-11:2004, EN60950-1:2006
USA UL ANSR: Intrusion Detection Units(UL639)
Installation/configuration notes
Mounting ConsiderationsSelect a location that is most likely to intercept anintruder moving across the coverage pattern. Ensurethe mounting surface is solid and vibration free. Avoidhot or cold drafts, direct sunlight, heat sources,windows, air conditioning outlets, and small animals.The DS307 does not detect through glass.
NoticeMisaligning the detector in an optional mountingbracket can reduce range.
Top ViewStandard Broad Coverage: 15 m x 15 m (50 ft x 50 ft)
Side ViewStandard Broad Coverage: 15 m x 15 m (50 ft x 50 ft)
Top ViewOptional Barrier Coverage (OMB77): 25 m x 5 m (80 ft x16 ft)
Side ViewOptional Barrier Coverage (OMB77): 25 m x 5 m (80 ft x16 ft)
Top ViewOptional Long Range Coverage (OMLR77): 36 m x 3 m(120 ft x 10 ft)
Side ViewOptional Long Range Coverage (OMLR77): 36 m x 3 m(120 ft x 10 ft)
Technical specifications
Electrical
Current Draw: 18 mA at 12 VDC
Voltage (Input): 6 VDC to 15 VDC
Environmental Considerations
Temperature(Operating):
-40°C to +49°C (-40°F to +120°F)For UL Listed Applications, 0°C to + 49°C(+32°F to +120°F)
Radio FrequencyInterference (RFI)Immunity:
No alarm or setup on critical frequencies in therange from 26 MHz to 950 MHz at 50 V/m.
Mechanical
Dimensions: 14.6 cm x 9.5 cm x 6.4 cm(5.75 in. x 3.75 in. x 2.5 in.)
Material: High impact ABS plastic enclosure
2 | DS307 PIR Intrusion Detector
Mounting
Height (recommended): 2 m to 2.6 m (6.5 ft to 8.5 ft)
Location: Surface or corner mount.
Internal Pointability: Coverage is adjustable ±10°horizontally, +1° to -18° vertically.
Outputs
Alarm: Form C contacts rated at 3.0 W, 125 mA at 28 VDC forresistive loads.
Tamper: Normally-closed. Contacts rated at 28 VDC, 125 mAmaximum.
Trouble: Solid state output, shorts to negative when activated.Maximum current load is 25 mA.
Ordering information
DS307 PIR Intrusion DetectorProvides Motion Analyzer II processing, PIRsupervision, motion Monitor supervision, an LEDindicator, and three sensitivity settings.Order number DS307
Accessories
B328 Gimbal‑mount BracketMounts on a single-gang box and allows rotation of adetector. Wires are hidden inside.Order number B328
Swiveling B335-3 low-profile mountSwiveling, low-profile, plastic mount for wall mounting.The vertical swivel range is +10° to -20°, while thehorizontal swivel range is ±25°. Available in triplepacks.Order number B335-3
B338 Universal Ceiling‑mount BracketSwiveling plastic mount for ceiling mounting. Thevertical swivel range is +7° to -16°, while the horizontalswivel range is ±45°.Order number B338
OMB77‑3 Barrier MirrorProvides barrier coverage with a 25 m x 5 m(80 ft x 16 ft) pattern. Shipped in packages of three.Order number OMB77-3
OMLR77‑3 Long‑range MirrorProvides long-range coverage with a 40 m x 3 m(120 ft x 10 ft) pattern. Shipped in packages of three.Order number OMLR77-3
TC6000 Test CordTest cord for connecting a compatible detector’s testpins to a voltmeter. It is 4.6 m (15 ft) long.Order number TC6000
3 | DS307 PIR Intrusion Detector
4 | DS307 PIR Intrusion Detector
Represented by:
Americas: Europe, Middle East, Africa: Asia-Pacific: China: America Latina:Bosch Security Systems, Inc.130 Perinton ParkwayFairport, New York, 14450, USAPhone: +1 800 289 0096Fax: +1 585 223 [email protected]
Bosch Security Systems B.V.P.O. Box 800025617 BA Eindhoven, The NetherlandsPhone: + 31 40 2577 284Fax: +31 40 2577 [email protected]
Robert Bosch (SEA) Pte Ltd, SecuritySystems11 Bishan Street 21Singapore 573943Phone: +65 6571 2808Fax: +65 6571 [email protected]
Bosch (Shanghai) Security Systems Ltd.201 Building, No. 333 Fuquan RoadNorth IBPChangning District, Shanghai200335 ChinaPhone +86 21 22181111Fax: +86 21 22182398www.boschsecurity.com.cn
Robert Bosch Ltda Security Systems DivisionVia Anhanguera, Km 98CEP 13065-900Campinas, Sao Paulo, BrazilPhone: +55 19 2103 2860Fax: +55 19 2103 [email protected]
© Bosch Security Systems 2013 | Data subject to change without notice2604027531 | en, V1, 01. Oct 2013
