Driveshaft installed. Bits and pieces – new oil seal.
-
Upload
deanna-furby -
Category
Documents
-
view
223 -
download
5
Transcript of Driveshaft installed. Bits and pieces – new oil seal.
![Page 1: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/1.jpg)
Driveshaft installed
![Page 2: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/2.jpg)
Bits and pieces – new oil seal
![Page 3: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/3.jpg)
Engine hoist from Bayfield Garage
![Page 4: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/4.jpg)
Tie the driveshaft to keep it in place
![Page 5: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/5.jpg)
mozzetto
![Page 6: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/6.jpg)
Grease the splines
![Page 7: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/7.jpg)
#9 on the hook – hoisting the engine to set it in place
![Page 8: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/8.jpg)
Meant for a Chevrolet V8 I’d say
![Page 9: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/9.jpg)
Right driveshaft assembled and ready to install, the motor is mounted to the frame
![Page 10: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/10.jpg)
See – it’s in.
![Page 11: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/11.jpg)
View from the rear, right driveshaft still to be installed
![Page 12: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/12.jpg)
Clean the ends and mount the ground strap
![Page 13: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/13.jpg)
Under the lights
![Page 14: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/14.jpg)
Right driveshaft – wedge in the mozzetto to allow it to move up and down the shaft
![Page 15: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/15.jpg)
You’ll need a small light to be able to see to line up the grooves in the crankcase where the driveshaft goes in
![Page 16: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/16.jpg)
A flexible light for dark spaces
![Page 17: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/17.jpg)
Return the hoist to the Bayfield Garage
![Page 18: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/18.jpg)
Right driveshaft installed – a lot of groaning and grunting while you lie on your back
![Page 19: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/19.jpg)
Cables and wires to be installed next
![Page 20: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/20.jpg)
Sunshine in the door
![Page 21: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/21.jpg)
Original cappuccio’s ( rubber bellows over the shifter cables)
![Page 22: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/22.jpg)
Ready to fill with 900ml of SAE 30 oil
![Page 23: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/23.jpg)
Reverse cable and clutch cable installed
![Page 24: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/24.jpg)
Hook up the gear change linkage
![Page 25: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/25.jpg)
Original distributor – new parts
![Page 26: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/26.jpg)
New points .15-.18 gap and new condensor – use a screwdriver with a magnetic end
![Page 27: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/27.jpg)
Insert a rod to set TDC – through the two holes and into a groove in the pulley
![Page 28: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/28.jpg)
Install the coil and coil wires – the black is the negative
![Page 29: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/29.jpg)
Install the distributor so the points are almost opening at TDC – final adjustment can be made with the slide
![Page 30: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/30.jpg)
Main cable to the dynastarter had worn through the casing exposing a copper wire which would ground out if it touched metal – electricians tape fixes that
![Page 31: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/31.jpg)
Coil to spark plug wire
![Page 32: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/32.jpg)
Plastic sleeves over the wire clamps protect the wiring, clean them prior to installation
![Page 33: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/33.jpg)
They’ll look like new
![Page 34: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/34.jpg)
Wire holder sheaths installed to protect the wiring
![Page 35: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/35.jpg)
Cable ends going to the dynastarter are dirty and corroded so file them clean before installation.
![Page 36: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/36.jpg)
Nice and shiny and ready to install
![Page 37: Driveshaft installed. Bits and pieces – new oil seal.](https://reader037.fdocuments.in/reader037/viewer/2022102923/551c2937550346a34f8b5f78/html5/thumbnails/37.jpg)
Dynastarter wires installed and tucked into their protected holders