TL-WR703N setup guide one – 3G router mode

TL-WR703N Is a new generation of mini 3G wireless router, compatible with the mainstream 3G

standard - CDMA2000 (China Telecom), WCDMA (China Unicom), TD-SCDMA (China Mobile). By

using the device to meet people to share 3G wireless broadband purposes.

Here we introduce the 3G TL-WR703N routing mode configuration.

TL-WR703N Quick setup:

Set by the Setup Wizard

Open the Device Management page "192.168.1.1", click "Setup Wizard", select "Next", optional

equipment, there are three access modes: 3G router mode, the wireless router mode, the wireless AP

mode, the default route for the 3G model.

Here we choose "3G router mode", click "Next", 3G dial-up configuration parameters, select the region

"China", the mobile ISP: optional, "China Telecom", "China Mobile" and "China Unicom" (according to

your Internet card formats to choose), the other default settings do not change.

注意： TL-WR703N Default has built in China Telecom, China Unicom mobile and dial the relevant

parameters, in general, as shown in the figure need only select the ISP operator interface can be

automatically set to dial numbers, APN user name and password and other information.

Click "Next" to set the wireless security.

Wireless Status: Wireless router, you must choose to open, so that the wireless network can access

and host access to the entire network.

SSID number: This identifies the wireless network name can be changed.

Channel: The wireless networking is used to select the frequency band (1-13).

Mode: a router that is used to select the operating mode, the choice of the bandwidth of the 802.11b

mode with 11M, 54M bandwidth 802.11g mode, 300M, 802.11n mode, 802.11b / g mixed mode and

802.11b / g / n mixed mode.

Band Bandwidth: Auto, 20MHz and 40MHz.

Maximum transmission rate: default.

Wireless Encryption: To ensure your wireless network from unauthorized access by others, it is

recommended to set the wireless encryption, the recommended encryption method is WPA-PSK/WPA2-

PSK.

On the computer through a wireless connection, as shown:

After setup is complete, click "Next" to restart the router, wait 1-3 minutes, check the device "running" -

"3G", you can see the IP address of the router has access to the necessary parameters such as the

Internet, the router dial-up has been successful, as shown, and you can normally get online.

TL-WR703N setting guide Two——Wireless router mode

Under router mode，TL-WR703N is equivalent to a wireless router, wired port as a WAN port, wireless-

LAN, all the wireless clients can share a broadband Internet line. The typical network application

structure as shown below.

Here TL-WR703N Router Quick Setup mode method.

One: TL-WR703N settings

Step 1: In the browser, enter "192.168.1.1", enter the login ID and password are admin, open the TL-

WR703N management interface, automatic pop-up "Setup Wizard" (the management interface can also

click the menu "Setup Wizard"), as shown below.

Step 2: Click "Next" to start setting up the wireless mode setting page as shown below.

Step 3: Select the "Router", click Next to bring up the wireless settings page, as shown below.

Step 4:: According to the decision to choose the front-end broadband connections to the Internet the

way, if you can enter recommended items. In this case the PPPOE example.

Step 5: Enter the broadband "Internet Account" and "Internet password", hit "Next", as shown below.

AS shown on the above page, you can set TL-WR703N the SSID (wireless network name that TP-

LINK_531984). To prevent unauthorized users rub network, it is recommended to set the wireless

security is recommended to select "WPA-PSK/WPA2-PSK" and set the PSK password (in this case

123456789).

Step 6: Click "Next" prompt to restart the device, as shown below.

Click "Restart", automatically restarting the router, setup is complete.

Step 7: Restart completed at this time TL-WR703N wireless network already set up wireless security,

the computer's wireless network connection is automatically disconnected, reconnect the TL-WR703N

need a wireless network (in this case the SSID to TP-LINK_531984), the connection process to enter

TL-WR703N wireless PSK password (in this case 123456789), connected to, the following figure.

If "WAN port state" view has access to the router to the IP and DNS server address, the PPPoE dial-up

success.

Thus TL-WR703N the Router mode has been configured, and successfully connected to the Internet,

wireless networks have been set WPA-PSK/WPA2-PSK wireless security. Computer has wireless

connectivity to the Internet router, the other computer simply connect the TL-WR703N can normally

access.

TL-WR703N Setup guide Three——Wireless AP modeAP mode using the wireless coverage capabilities for traditional wired LAN to provide wireless access to

extension.

First, connect TL-WR703N with front-end wired LAN connections, wireless device sends the wireless

signal coverage to meet the extended family and small and medium wireless access.

Here we introduce the TL-WR703N wireless AP mode configuration.

TL-WR703N Setting:

Step 1: Connect to TL-WR703N. As the TL-WR703N in AP mode, the default DHCP server is not open,

the computer can not automatically assign IP addresses, so you need to configure the wireless network

to connect the computer's IP address in order to visit the router management interface. Computer

wireless network connection IP address is set to 192.168.1.X (1 ≤ X ≤ 252), subnet mask:

255.255.255.0, as shown below. After setup is complete, click "OK" to take effect. TL-WR703N default

management IP address "192.168.1.1".

Note: The computer's IP address configuration can refer to the following link:

http://www.tp-link.com.cn/pages/article-detail.asp?result=school&d=72

Step 2：TL-WR703N did not set the default wireless security. Computer through a wired or wireless

connection to TL-WR703N (in xp system to TL-WR703N wireless connection for example), scan the

environment in the wireless network, select the TL-WR703N wireless SSID, and click "Connect" to

connect the later, as shown below.

Step 3: In the browser, type "192.168.1.1", enter the login user name and password are admin, open the

TL-WR703N management interface, automatic pop-up "Setup Wizard" (the management interface can

also click the menu "Setup Wizard") , as shown below.

Step 4: Click "Next" to start setting up mode settings page, select "wireless AP mode" as shown below.

Step 5: According to the need to select the AP mode, this example select the "access point mode", the

other mode of reference 700N setting mode, as shown below.

Step 6: Click "Next" to bring up the wireless settings page, as shown below.

As shown on the above page, you can set TL-WR703N the SSID (the wireless network name). To

prevent unauthorized users rub network, it is recommended to set the wireless security is recommended

to select "WPA/WPA2- Personal Edition" and set the password (in this case abcdefgh).

Step 7: Click "Next" prompt to restart the device, as shown below.

Click "Restart", automatically restarting the router, setup is complete.

Step 8: Restart completed at this time TL-WR703N wireless network already set up wireless security,

the computer's wireless network connection is automatically disconnected, reconnect the TL-WR703N

need a wireless network (in this case the SSID to TP-LINK_531984), the connection process to enter

TL-WR703N wireless PSK password (in this case abcdefgh), connected to, the following figure.

Step 9: After configuration is complete, the IP address of your wireless network connection to re-set to

the original configuration (usually automatically obtain an IP address), click "OK" effect, in order to

properly connect to the Internet, as shown below. .

Note: TL-WR703N default management IP address "192.168.1.1", it must be TL-WR703N the LAN IP

address set to the wired LAN devices are not all the same IP address to prevent IP address conflicts

(under normal circumstances do not change). In the menu "network parameters" - "LAN port settings",

change IP, click the "Save", the router automatically restart. As shown below.

Thus TL-WR703N AP mode configuration is completed, then the computer search to TL-WR703N

issued wireless SSID is TP-LINK_531984, PSK key is abcdefgh.

TL-WR703N Setup guide Four——The wireless network wireless AP mode

TL-WR703N in wireless applications, has the following three application modes: wireless AP mode, the

wireless router mode, 3G wireless routing model, this paper focuses on the wireless AP mode, an

introduction to a variety of applications. Mode and 3G wireless router wireless router mode, please refer

to other relevant documents.

Time during the Setup Wizard, select the wireless AP mode, according to the need to select all in AP

mode working application mode, as shown below:

As the TL-WR703N in AP mode, the default DHCP server is not open, the computer can not

automatically assign IP addresses, so you need to configure the wireless network to connect the

computer's IP address in order to visit the router management interface.

Computer wireless network connection IP address is set to 192.168.1.X (1 ≤ X ≤ 252), subnet mask:

255.255.255.0, as shown below. After setup is complete, click "OK" to take effect. TL-WR703N default

management IP address "192.168.1.1".

Note: The computer's IP address configuration can refer to the following link:

http://www.tp-link.com.cn/pages/article-detail.asp?result=school&d=72

（One）Here we introduce the TL-WR703N wireless AP mode, repeater mode (Repeater) under the

application.

TL-WR703N setting

Step 1: Click relay mode (Repeater), the display as shown below

Step 2: Fill in the remote AP's ssid, mac address or click the scan, in which the pop-up list to select the

front end relay to connect to the SSID of the router, and enter the front of the router with the same

encryption type and key.

Step 3: Click Next, restart the computer to take effect.

（ Two ） Here we introduce the TL-WR703N wireless AP mode, client mode (Client) under the

application.

TL-WR703N setting

Step 1: Click to select client mode (Client), the pop-up as shown below:

Step 2: Manually enter the front-end router's SSID, or scan the list and click Connect, and select the

front-end router with the same encryption method, enter the correct password. As shown below:

Step 3: Click Next, restart the computer to take effect.

（Three）Here we introduce the TL-WR703N wireless AP mode, Bridge mode (Bridge with AP) under

the application.

① TL-WR703N and 11g router wireless bridge configuration

Note: TL-WR703N in the choice of bridge mode (Bridge with AP), supports the following encryption

types: WEP, no encryption, without modifying the wireless security settings. (For this example select

WEP for wireless encryption)

In this case 11g router TL-WR541G +, for example, the network topology is as follows:

The following picture shows the TL-WR541G + user interface, set the wireless parameters to specify the

channel 6, open the bridge feature of the bridge on the side and fill in the TL-WR703N device MAC

address, and open the security settings, as shown below:

Below into the TL-WR703N wireless configuration interface configuration:

Step 1: Go to bridged mode, as shown:

Step 2: Scan the pop-up list and choose to connect to the network SSID, as shown:

Step 3: click Next, you need to reboot the router to take effect.

Note: TL-WR703N default management IP address "192.168.1.1 to prevent IP address conflicts, they

should be TL-WR703N the LAN IP address set to the wired LAN devices are not all the same IP

address (in general under no change) can be in the menu "network parameters" - "LAN port settings",

change IP, click the "Save", the router automatically reboot as shown below.

② TL-WR703N and 11n wireless router bridge configuration

In this case the TL-WR740N with TL-WR703N bridge, for example.

In the TL-WR703N and 11n wireless bridge products, only need to open the 11n products on the TL-

WR703N WDS function to scan and connect, of course, need to maintain the same channel, encryption

type, key.

Step 1: First you need to configure TL-WR703N wireless parameters, for example here is a designated

channel, the wireless security settings, encryption type and key support WEP, WPA-PSK/WPA2-PSK

encryption, WEP encryption, for example here is

Step 2: TL-WR740N wireless WDS opens, set the following:

Click scan, in which the pop-up list select TL-WR703N the SSID, and select TL-WR703N the same

encryption type and enter the correct key, as shown:

Click Save, the following window appears, can be completed:

Note: TL-WR703N default management IP address "192.168.1.1 to prevent IP address conflicts, they

should be TL-WR703N the LAN IP address set to the wired LAN devices are not all the same IP

address (in general under no change) can be in the menu "network parameters" - "LAN port settings",

change IP, click the "Save", the router automatically reboot as shown below.