Dr. S. M. MUZAKKIR · 11. S M Muzakkir, 2016, Synthesis of Magneto Rheological Fluid and Evaluation...
Transcript of Dr. S. M. MUZAKKIR · 11. S M Muzakkir, 2016, Synthesis of Magneto Rheological Fluid and Evaluation...
1
Dr. S. M. MUZAKKIR Associate Professor Department of Mechanical Engineering, Faculty of Engineering & Technology, Jamia Millia Islamia, Maulana Mohammad Ali Johar Marg, Jamia Nagar, New Delhi-110025 INDIA
Phone: +91 11 26981259 Fax: +91 11 2698 0229 E-mail: [email protected] PROFESSIONAL QUALIFICATIONS
Ph.D. (Tribology) from Indian Institute of Technology Delhi, IIT Delhi, 2015
M. Tech. (Design of Mechanical Equipment) from Indian Institute of Technology Delhi, IIT Delhi, 1996
B. Sc. Engg. (Mechanical) from Jamia Millia Islamia, New Delhi, 1990.
ACADEMIC AREAS OF INTEREST
Design of Mechanical Equipment
Tribology
Product Design
TEACHING EXPERIENCE
S. No. From To Position Held Name of Institute
(v) 2007 till date Associate Professor
Mechanical Engineering Department, Jamia Millia Islamia, New Delhi
(iv) 2005 2007 Lecturer (Selection grade)
Mechanical Engineering Department, Jamia Millia Islamia, New Delhi
(iii) 2000 2005 Senior Lecturer Mechanical Engineering Department, Jamia Millia Islamia, New Delhi
(ii) 1995 2000 Lecturer Mechanical Engineering Department, Jamia Millia Islamia, New Delhi
(i) 1991 1995 Lecturer University Polytechnic, Jamia Millia Islamia, New Delhi
Residential address B-18, Mujeeb Bagh Staff Quarters, Jamia Millia Islamia, Jamia Nagar New Delhi 110025, INDIA
2
SUBJECTS TAUGHT AT POSTGRADUATE AND UNDERGRADUATE LEVELS Postgraduate Level Mechanical Engg. Design, Vibration Engg., Optimization Methods, Concurrent Engineering, Robotics Graduate Level Machine Design, Mechanical Vibrations, Machine Dynamics, Robotics, Automobile Engineering, Computer Aided Machine Drawing RESEARCH PAPERS PUBLISHED
Publications in Journals [1][2][3][4][5][6][7][8][9]–[17][18]–[33][12], [34]–[40]
[1] S. M. Muzakkir, H. Hirani, G. D. Thakre, and M. R. Tyagi, “Tribological failure analysis
of journal bearings used in sugar mills,” Eng. Fail. Anal., vol. 18, no. 8, pp. 2093–2103,
Dec. 2011.
[2] S. M. Muzakkir, H. Hirani, and G. D. Thakre, “Lubricant for Heavily Loaded Slow-
Speed Journal Bearing,” Tribol. Trans., vol. 56, no. 6, pp. 1060–1068, Nov. 2013.
[3] S. M. Muzakkir, K. P. Lijesh, and H. Hirani, “Tribological Failure Analysis of a Heavily-
loaded Slow Speed Hybrid Journal Bearing,” Eng. Fail. Anal., vol. 40, pp. 97–113, 2014.
[4] S. M. Muzakkir, K. P. Lijesh, H. Hirani, and G. D. Thakre, “Effect of cylindricity on the
tribological performance of the heavily loaded slow speed journal bearing,” J. Eng.
Tribol., vol. 229, no. 2, pp. 178–195, 2014.
[5] S. M. Muzakkir, K. P. Lijesh, and H. Hirani, “Influence of surfactants on tribological
behaviors of MWCNTs (multi-walled carbon nano-tubes),” Tribol. - Mater. Surfaces
Interfaces, no. February, pp. 1–8, 2016.
[6] K. P. Lijesh, S. M. Muzakkir, H. Harish, and G. D. Thakre, “Control on wear of journal
bearing operating in mixed lubrication regime using grooving arrangements,” Ind. Lubr.
Tribol., vol. 68, no. 4, 2016.
[7] K. P. Lijesh, S. M. Muzakkir, and H. Hirani, “Rheological measurement of
redispersibility and settling to analyze the effect of surfactants on MR particles,” Tribol. -
Mater. Surfaces Interfaces, vol. 10, no. 1, pp. 53–62, 2016.
[8] K. P. Lijesh, S. M. Muzakkir, and H. Hirani, “Failure mode and effect analysis of passive
magnetic bearing,” Eng. Fail. Anal., vol. 62, pp. 1–20, 2016.
[9] S. M. Muzakkir, “Modelling of Push Rod Type Valve System for Minimization of
3
Frictional Losses,” Int. J. Emerg. Trends Eng. Dev., vol. 3, no. 5, pp. 102–109, 2015.
[10] S. M. Muzakkir, “Design and Development of Experimental setup for Direct Acting
Overhead Camshaft (DOHC) Valve System,” Int. J. Curr. Eng. Technol., vol. 5, no. 3, pp.
2027–2031, 2015.
[11] S. M. Muzakkir, “Effectiveness of Carbon Nanotubes ( CNT ) as Lubricant Additive in
Mixed Lubrication Conditions,” Int. J. Emerg. Trends Eng. Dev., vol. 3, no. 5, pp. 261–
266, 2015.
[12] S. M. Muzakkir, “Experimental Investigations on Effect of Tungsten Disulphide (WS2)
on Wear Performance of Commercial Lubricant under Mixed Lubrication Conditions,”
Int. J. Curr. Eng. Technol., vol. 5, no. 2, pp. 2014–2016, 2015.
[13] S. M. Muzakkir, “Enhancement of Wear Performance of Commercial Lubricant using
Zinc (Zn) Nano-Particles as Anti-Wear Additive under Mixed Lubrication Conditions,”
Int. J. Eng. Res., vol. 5, no. 2, pp. 2014–2016, 2015.
[14] S. M. Muzakkir, “Kinematic , Dynamic and Tribological Analysis of Push Rod Type
Valve System,” Int. J. Adv. Ind. Eng., vol. 3, no. 2, pp. 54–59, 2015.
[15] S. M. Muzakkir, “Design of Valve System using Upgradation Approach,” Int. J. Appl.
Eng. Res., vol. 11, no. 1, pp. 712–722, 2016.
[16] S. M. Muzakkir, “Methodology for the Control of Wear of Journal Bearing Operating in
Mixed Lubrication Regime,” Int. J. Appl. Eng. Res., vol. 11, no. 1, pp. 689–692, 2016.
[17] S. M. Muzakkir, “A Novel Approach for the Design of Valve System,” Int. J. Appl. Eng.
Res., vol. 11, no. 2, pp. 1464–1468, 2016.
[18] S. M. Muzakkir and H. Hirani, “Experimental Investigation on Effect of Particle Sizes of
Molybdenum Disulphide on Wear Under Heavy Load and Slow Speed Conditions,” Int. J.
Mod. Eng. Res., vol. 4, no. 12, pp. 46–49, 2014.
[19] S. M. Muzakkir and H. Hirani, “Design of Valve System using Optimization Approach,”
Int. J. Curr. Eng. Technol., vol. 5, no. 2, pp. 1217–1223, 2015.
[20] S. M. Muzakkir and H. Hirani, “A Magnetorheological Fluid Based Design of Variable
Valve Timing System for Internal Combustion Engine using Axiomatic Design,” Int. J.
Curr. Eng. Technol., vol. 5, no. 2, pp. 603–612, 2015.
4
[21] S. M. Muzakkir and H. Hirani, “Effect of Molybdenum Disulfide Particle Sizes on Wear
Performance of Commercial Lubricant,” Int. J. Sci. Eng. Technol., vol. 4, no. 3, pp. 162–
164, 2015.
[22] S. M. Muzakkir and H. Hirani, “Innovative-Tribo-Design of Variable Valve Timing
Mechanism : Need and Concept,” Int. J. Curr. Eng. Technol., vol. 5, no. 2, pp. 1115–
1125, 2015.
[23] S. M. Muzakkir and H. Hirani, “Experimental Investigation on Effect of Grinding
Direction on Wear Under Heavy Load and Slow Speed Conditions with Molybdenum
Disulphide (MoS 2) as Additive in Commercial Lubricant,” Int. J. Eng. Res., vol. 5013,
no. 4, pp. 102–104, 2015.
[24] S. M. Muzakkir, H. Hirani, and G. D. Thakre, “Experimental Investigations on
Effectiveness of Axial and Circumferential Grooves in Minimizing Wear of Journal
Bearing Operating in Mixed Lubrication Regime,” Int. J. Curr. Eng. Technol., vol. 5, no.
1, pp. 486–489, 2015.
[25] S. M. Muzakkir and S. Kumar, “Design of Mechanical Oil Seal and Gasket,” Int. J. Appl.
Eng. Res., vol. 10, no. 12, pp. 30911–30926, 2015.
[26] S. M. Muzakkir and K. P. Lijesh, “Studies on Control Aspects of Active Magnetic
Bearings,” Int. J. Curr. Eng. Technol., vol. 5, no. 4, pp. 2465–2471, 2015.
[27] S. M. Muzakkir, K. P. Lijesh, and H. Hirani, “Effect of Base Oil on the Anti-Wear
Performance of Multi-Walled Carbon Nano-tubes (MWCNT),” Int. J. Curr. Eng.
Technol., vol. 5, no. 2, pp. 681–684, 2015.
[28] S. M. Muzakkir, K. P. Lijesh, and H. Hirani, “Carbon Nanotubes as Solid Lubricant
Additives for Anti- wear Performance Enhancement under Mixed Lubrication
Conditions,” Int. J. Mod. Eng. Res., vol. 5, no. 2, pp. 25–28, 2015.
[29] S. M. Muzakkir, K. P. Lijesh, and H. Hirani, “Fail-safe design of journal bearing
hybrized with passive magnetic levitation,” Int. J. Appl. Eng. Res., vol. 10, no. 14, pp.
34707–34711, 2015.
[30] S. M. Muzakkir, M. G. Patil, and H. Hirani, “Design of Innovative Engine Valve :
Background and Need,” Int. J. Sci. Eng. Technol., vol. 181, no. 4, pp. 178–181, 2015.
[31] S. M. Muzakkir, M. G. Patil, and H. Hirani, “Design of Innovative Engine Valve,” Int. J.
5
Sci. Eng. Technol., vol. 4, no. 3, pp. 212–217, 2015.
[32] S. M. Muzakkir and V. Talreja, “Design of Flywheel for Maximization of Storage
Energy using ANSYS,” Int. J. Appl. Eng. Res., vol. 10, no. 19, pp. 40291–40300, 2015.
[33] S. M. Muzakkir, K. P. Lijesh, and H. Hirani, “Failure Mode and Effect Analysis of
Journal Bearing,” Int. J. Appl. Eng. Res., vol. 10, no. 16, pp. 37752–37759, 2015.
[34] K. P. Lijesh, S. M. Muzakkir, and H. Hirani, “Failure Analysis of Rolling Contact
Bearing for Flywheel Energy Storage Systems,” Int. J. Curr. Eng. Technol., vol. 5, no. 1,
pp. 439–443, 2015.
[35] K. P. Lijesh, S. M. Muzakkir, and H. Hirani, “Experimental Study of the Parameters
Affecting the Tribological Performance of Nano Lubricant Containing Multi-Walled
Carbon Nano-tubes ( MWCNT ) using Design of Experiments ( DOE ),” Int. J. Mod. Eng.
Res., vol. 5, no. 3, pp. 66–70, 2015.
[36] K. P. Lijesh and S. M. Muzakkir, “Models for Boundary Lubrication,” Int. J. Appl. Eng.
Res., vol. 10, no. 24, pp. 45533–45540, 2015.
[37] K. P. Lijesh and S. M. Muzakkir, “Experimental Evaluation of MR Brake with Elliptical
Profile,” Int. J. Appl. Eng. Res., vol. 10, no. 24, pp. 45541–45545, 2015.
[38] K. P. Lijesh and S. M. Muzakkir, “Problems related to Synthesis and Application of MR
Fluids,” Int. J. Appl. Eng. Res., vol. 10, no. 24, pp. 45489–45495, 2015.
[39] K. P. Lijesh and S. M. Muzakkir, “Service Life Estimation of Rubber Seals,” Int. J. Appl.
Eng. Res., vol. 10, no. 24, pp. 0–5, 2015.
[40] K. P. Lijesh, S. M. Muzakkir, and H. Hirani, “Experimental tribological performance
evaluation of nano lubricant using multi-walled carbon nano-tubes (MWCNT),” Int. J.
Appl. Eng. Res., vol. 10, no. 6, pp. 14543–14550, 2015.
Publications in International Conferences
1. S M Muzakkir, H Hirani, G D Thakre and M R Tyagi, 2010, Study of Lubrication
Aspects of Journal Bearing Failure in a Sugar Mill, International Conference on
Industrial Tribology 02-04 Dec, 2010, RDCIS, SAIL, Ranchi, India
(Received best paper award).
6
2. S M Muzakkir, H Hirani and G D Thakre, 2012, Experimental Performance Evaluation
of Thick Lubricating Oils used in Journal Bearings of Sugar Mill, 14th Lubricating
Grease Conference, February 2-4, 2012, Jaipur, India
3. S M Muzakkir, H Hirani and G D Thakre, 2012, Performance Evaluation of Journal
Bearings used in Sugar Mills using Taguchi Method, STLE Annual Meeting &
Exhibition, May 6-10, 2012, Missouri, USA
4. S M Muzakkir and Lijesh K P., 2015, Experimental Investigations on Effectiveness of
Molybdenum Disulphide and Zinc Nano Particles as Lubricant Additive in Mixed
Lubrication Conditions, International Conference on Recent Advances in Nano Science
and Technology (RAINSAT-2015) 8-10 July, 2015, Sathyabama University & CLRI
(CSIR), Chennai
5. S M Muzakkir and Lijesh K P., 2015, Influence of Surfactant on Usage of
Functionalized Multi Walled Carbon Nano Tubes (MWCNT) as Lubricant Additive,
International Conference on Recent Advances in Nano Science and Technology
(RAINSAT-2015) 8-10 July, 2015, Sathyabama University & CLRI (CSIR), Chennai.
(Received best paper award).
6. S M Muzakkir and Lijesh K P., 2015, Is Nano Size the Best Choice?, International
Conference on Recent Advances in Nano Science and Technology (RAINSAT-2015) 8-10
July, 2015, Sathyabama University & CLRI (CSIR), Chennai
7. S M Muzakkir and Lijesh K P., 2015, Tribological Performance Evaluation of Nano-
lubricant, International Conference on Recent Advances in Nano Science and Technology
(RAINSAT-2015) 8-10 July, 2015, Sathyabama University & CLRI (CSIR), Chennai
8. S M Muzakkir, Lijesh K P., Hirani H. and Thakre, G.D., 2015, Control On Wear of
Journal Bearing Operating In Mixed Lubrication Regime Using Grooving Arrangements,
International Conference on Tribology (TURKEYTRIB’15) Yıldız Technical University,
Istanbul, Turkey.
9. S M Muzakkir, Lijesh K P. and Hirani H., 2015, Influence of Surfactants on
Tribological Behaviors of MWCNT (Multi-walled Carbon Nanotubes), International
Conference on Tribology (TURKEYTRIB’15) Yıldız Technical University, Istanbul,
Turkey.
7
10. S M Muzakkir, Lijesh K P. and Hirani H., 2015, Rheological Measurement of
Redispersibility and Settling to Analyze the Effect of Surfactants on MR Particles,
International Conference on Tribology (TURKEYTRIB’15) Yıldız Technical University,
Istanbul, Turkey. (Ranked among top ten research papers).
11. S M Muzakkir, 2016, Synthesis of Magneto Rheological Fluid and Evaluation of its
Tribological Properties, International Conference and Exhibition on Building Utilities,
(ICEBU-16) Jamia Millia Islamia, New Delhi.
(Received best paper award).
12. M N Eqbal, H Z Jafri, S.M. Muzakkir, 2017, Modal Analysis of a Mechanical Structure,
International Conference on Quality, Productivity Reliability, Optimization and
Modelling (ICQPROM), New Delhi.
Best Paper Awards
1. International Conference on Industrial Tribology 02-04 Dec, 2010, RDCIS, SAIL,
Ranchi, India.
2. International Conference on Recent Advances in Nano Science and Technology
(RAINSAT-2015) 8-10 July, 2015, Sathyabama University & CLRI (CSIR), Chennai.
3. International Conference and Exhibition on Building Utilities, (ICEBU-16) Jamia Millia
Islamia, New Delhi.
Invited Lectures
1. Failure Analysis of Mechanical Systems: Role of Standards, Training Program on
“Standards and Measurement of Customer Satisfaction for ONGC Engineers” IIT Delhi,
2013
2. Introduction to Design of Mechatronics System, Faculty Development Program on
“Mechatronics and Robotics in Manufacturing Industries”, JMI, New Delhi, 2015
3. Effect of Cylindricity on the Tribological performance of Journal Bearing, AICTE QIP
STC on “Fundamentals of Engineering Tribology with Applications” IIT Delhi, 2015
4. Lubricant Additives, AICTE QIP STC on “Fundamentals of Engineering Tribology with
Applications”, IIT Delhi, 2015
8
Other Responsibilities
Technical (Certifying) Officer of University (1999 onwards)
Placement Coordinator, Deptt. of Mechanical Engineering (2013 onwards)
Nodal Officer, Deptt. of Mechanical Engineering (2015 onwards)
Time Table Incharge, Deptt. of Mechanical Engineering (1995-2010, 2013 till date)
Team Mentor, Smart India Hackathon-2017
Incharge, Mechanical Vibrations Laboratory (2005-2010, 2013 till date)
Incharge, Machine Dynamics Laboratory (1995-2010, 2013 till date)
Editor, International Journal of Engineering and Industries
Member, Editorial Advisory Board, Canadian Journal of Basic and Applied Sciences
Reviewer, i) Journal of Advances in Mechanical Engg and Science
ii) Tribology Transactions
iii) Advances in Tribology
iv) Wear
v) Tribology in Industry
vi) Tribology International
Faculty Advisor, Indian Society of New Era Engineers (Students Society)
Coordinator, B.Tech. Project
Membership of Professional Bodies
Life member, Tribology Society of India, India
Life member, Mechanical Engineering Society, India
Formerly Educator Associate Member, American Institute of Aeronautics and
Astronautics (AIAA) (2015)
Organization of Faculty/Students Development Program
Faculty Development Program on Mechatronics & Robotics in Manufacturing Industries
(27 Feb, 2015 to 12 Mar, 2015)
Faculty Development Program on CFD using ANSYS (21-22 March, 2016) Sponsored
by ANSYS Inc.
Student Development program on CFD using ANSYS (2 - 4 March, 2016) Sponsored by
ANSYS Inc.
9
Upcoming Book Chapters
1. Chapter Title: Novel Approach for the Design of Valve System
Book Title: Advanced Engineering Research and Applications
Editors: B.S. Ajaykumar and D. Sarkar
Publisher: Research India Publications, ISBN No. 978-93-84443-48-1
2. Chapter Title: Design of valve system using up-gradation approach
Book Title: Introduction to Mechanical Engineering
Editor: S. Rajendran
Publisher: Research India Publications, ISBN No. 978-93-84443-49-8
3. Chapter Title: Methodology for the control of wear of journal bearing operating in mixed
lubrication regime
Book Title: Advances in Chemistry and Chemical Engineering
Editors: David N. Reinhoudt and Hongkai WU
Publisher: Research India Publications, ISBN No. 978-93-84443-47-4