Dr. APJ ABDUL KALAM GOVT. COLLEGE - DNH
Transcript of Dr. APJ ABDUL KALAM GOVT. COLLEGE - DNH
Dr. APJ ABDUL KALAM GOVT. COLLEGE(SILVASSA COLLEGE)
College of Arts, Commerce & Science(Affiliated with Gujarat University, Ahmedabad) (College Code: 509)
Dadra and Nagar Haveli Ucchha Shikshya Samiti, SilvassaSilvassa-396230.
No.EDN/SC/SCI LAB/NCB/2015/394/17 Date: 27/11/2015
E- Tender Notice
I/c. Principal, Dr. APJ Abdul Kalam Govt. College, Dadra & Nagar HaveliUcchha Sikshya Samiti, Silvassa invites sealed tenders through On-Line onhttps://dnh.nprocure.com or http://www.nprocure.com for supply of Worktables and othermaterials of size and specifications as mentioned in Annexure-I for Science Laboratories ofDr. APJ Abdul Kalam Govt. College attached herewith from the reputed Authorisedmanufactures as per the schedule mentioned below:-
*Online downloading start 28 /11/2015
*Bid Document download ended 19/12/2015 12:00 Hrs
*Last date and time for receipt of Bid. _ 19/12/2015 15:00 Hrs
Physical submission along with Sample of tender,fees, EMD, Experience Certificate, Registration,VAT Registration and other documents etc. in hardcopy in the office of the tender inviting authority byRPAD/ Speed Post./ Courier. In case, physicalsubmission through RPAD/speed post/ courier, theTender Inviting Authority shall not be responsible forany postal delay or loss of documents.
_20/12/2015 14:00 Hrs
*Online Technical bid opening 21/12/2015 at 12:00 hrs
*Online opening of Price bid(Date of price bid opening can be extended)
22/12/2015 at 12:00 hrs
*Bidders have to submit price bid in Electronic Format only on https:// dnh.nprocure.comwebsite till the date and time for submission. Price Bid in Physical format shall not beaccepted in any case.
The Tender Inviting Authority reserves the right to accept or reject any or all the tenderreceived without assigning any reasons thereof.Bidder shall have to post their queries on E-mail Address: [email protected] on orbefore 19/12/2015 up to 14:00 hrsIn case bidder needs any clarification or if training required of participating in onlinetender, they can contact the following office:-“(n) Code Solution-A Division, GNFC Ltd”403, GNFC Info Tower, Bodakdev,Ahemdabad-380054, Gujarat (India)Email- [email protected] Fax:- +91 79 26857321Website:- www.nprocure.com
Sd/-(H. K. Patel)
Admin-cum-Accounts Officer,Dr. APJ Abdul Kalam Govt. College
SilvassaCopy to:-
1. The Chief Publicity Officer, Dadra & Nagar Haveli, Silvassa for publishing it in oneleading widely circulated news paper in adjoining States of Gujarat and Maharashtra.
2. The Director (Information & Technology), Dadra & Nagar Haveli, Silvassa fordisplaying it on the official website of DNH i.e. www.dnh.nic.in
3. Guard File.
Dr. APJ ABDUL KALAM GOVT. COLLEGE(SILVASSA COLLEGE)
College of Arts, Commerce & Science(Affiliated with Gujarat University, Ahmedabad) (College Code: 509)
Dadra and Nagar Haveli Ucchha Shikshya Samiti, SilvassaSilvassa-396230.
No.EDN/SC/SCI LAB/NCB/2015/394/17 Date:27/11/2015
Terms and Conditions
Sealed Tenders are hereby invited on behalf of I/c. Principal, Dr. APJAbdul Kalam Govt. College, Dadra & Nagar Haveli Ucchha Sikshya Samiti, Silvassa forsupply of Worktables and other materials of size and specifications as mentioned inAnnexure-I for Science Laboratories attached herewith from the reputed manufactures
Terms & Conditions for supply of Worktables and other materials for ScienceLaboratories of Dr. APJ Abdul Kalam Govt. College, Dadra Nagar Haveli Ucchha SikshyaSamiti, Silvassa are as follows:
1. Tenders are invited by E-Tendering system so the ‘Technical Bid’ will be submitted
in the office with Envelop written as ‘Technical Bid’. It should contain full
information as required in Annexure – III (Technical Bid) provided herewith.
a. The ‘Financial Bid’ will have to be applied online through E-procurement.
2. The bidder should be An ISO 9001: 2008 and 14001:2004 certified organizations.
3. The Rates quoted should be for free delivery at F.O.R. Silvassa College, Dokmardi
(DNH) and should be valid one year from the date of opening of tenders.
4. The rates quoted should be inclusive of all taxes, duties, royalties, octroi etc. payable
on the sales or transport within and /or outside the State including installation charges
shall be payable by the supplier.
5. No extra charges for packaging, forwarding and insurance etc., will be paid on the
rates quoted.
6. The rates should be quoted only for the first class and standard quality items.
7. The bidder shall have more than 20,000 square feet production area.
8. The bidder shall have at-least five years experience for manufacturing and
commissioning for Laboratory set up.
9. The bidder shall have completed the minimum 02 projects of for the value of one
crore or two project of 40 lakhs and three projects of 20 lakhs for setup of college
laboratory. Copy of Supply Order should be attached.
10. The bidder should have all own machinery to ensure In house production.
11. The bidder shall have also in-house powder coating facility with 8 to 9 tank chemical
pre- treatment process and finished with highly corrosion resistant Akzonble
/Polybond/equivalent epoxy based powder coating with 70-80 microns thickness and
500 hours salt spray test capability.
12. The bidders shall have Quality check laboratory for Furnitures and products according
to the SEFA Guide Lines.
13. Product testing will be compulsory according to the SEFA norms and guidelines.
14. Warranty: The product should carry at least warranty of 18th months from the date
of supply and onsite service warranty will be for 5 years from the date of final
installation.
15. The bidders have submit Sample / Mockup one Lab Table along with the
TECHNICAL BID (For verification of quality etc.) as per Specifications mentioned in
Annexure-II.
16. In first instance, the Physical Sample and Technical Bid of all the bidders will verified
and if found to be satisfactory thereafter the Financial Bids of the Eligible Tenderers
only will be considered for the said Tender.
17. No Charges will be paid for the Physical Sample to the unsuccessful bidders.
18. The Collection of the physical samples of the non selected tenderers shall be made
within 20 days from the opening of the Financial Bid from this Institute. There will be
no responsibility of this Institute after 20 days regarding miss-placement, breakage,
theft etc.
19. Physical Sample of the successful bidder will be considered within the supply order
20. The bidder shall have an annual financial gross turnover of not less than Rs. 5 Crores
(Rupees Five Crores only) for manufacture and supply of Lab. Furniture etc. during
any of the last Two financial years.
21. The bidder shall have to submit Test Certificates from supplier of Raw Materials with
seal and signature.
22. The bidder will have to submit Quality Control Certificate with photographs of test
process with the final products.
23. Our Technical team/ purchase committee will do Physical verification for factory
premises and machineries.
24. Our Technical Team/purchase committee will do Factory Acceptance Test before
leaving final product from the company.
25. Tenders received after due date and time mentioned in E-Tender Notice will not be
accepted.
26. Tenderer shall have to deposit Rs. 2000/- (Rupees One Thousand only) for Tender
fees (non-refundable) by Demand Draft in favour of “Silvassa College” payable at
Silvassa. The Tender fees submitted in any form other than mentioned above will not
be accepted. Tender received without Tender fees will be summarily rejected.
27. Demand Draft/FDR of any Nationalised Bank should accompany Tender application
duly completed in all respect for Rs.3,00,000/- (Rupees Three Lakhs only) as Earnest
Money Deposit (EMD) in favour of “Silvassa College”. The EMD submitted in any
form other than mentioned above will not be accepted. The Tenders received without
EMD will be summarily rejected.
28. The submission of EMD is compulsory for all the tenderers and no exemption will be
granted for submission of EMD in any case.
29. The tenderer will be bound by the details furnished by him / her to this office, while
submitting the tender or at subsequent stage. In case, any of such documents furnished
by him/her is found to be false at any stage, it would be deemed to be a breach of
terms of contract making him / her liable for legal action besides termination of
contract/supply order.
30. The received tenders which do not confirm with the terms and conditions of this
office will be summarily rejected.
31. No separate agreement will be required to be signed by the successful tenderer (s) for
the supply. Rates offered in the response to the concerned Tender shall be considered
as acceptance of all terms and conditions for supply for all legal purposes.
32. No advance payment will be made and no request for increase in the rates will be
entertained during the period of supply.
33. The successful bidder will have to deposit security amount equal to 10% of the bid
price for one year in form of Demand Draft/ FDR of any Nationalised Bank within 10
days of receipt of Supply Order.
34. Non-receipt of the Security Deposit within stipulated time limit will result in
automatic cancellation of the contract without any intimation.
35. All bills should be in duplicate and should invariably mention all taxes i.e. Vat,
excise, Service tax etc alongwith date and number of supply order.
36. All bills should be pre-receipted on a revenue stamp of proper value. Bills, which are
not pre-receipted on revenue stamp, will not be accepted for payment.
37. Each bill in which Sales Tax is charged must contain the following certificate on the
body, of the bill “Certified that the goods on which Sales tax /VAT/ Service tax has
been charged have not been exempted under the C.S.T./VAT/Act or the rules made
there under and the amount charged on account of sales tax on these goods is not
more than what is payable under the provision of relevant act of the rules made there
under”.
38. The supply of items should be completed within 30 days from the date of work
order/supply order.
39. The right to enhance/reduce the quantity of supply order is reserved with the tender
inviting authority.
40. The tendering firm must be registered with the Sales Tax /VAT/Excise Department
and a copy of their registration have to submit.
41. If the supply of items are not satisfactory or not as per specification given in the
tender, the same will be rejected by the Tender Inviting Authority and same will have
to be replaced by the supplier at his own cost & risk.
42. In case of the failure to replace the unaccepted & rejected articles from supplies made
as mentioned above in the conditions, the loss undergone by the Institution will be
recovered from the suppliers Earnest Money Deposit or payment due of any bill (s) to
the extent required.
43. In case the supplier does not execute the supply order in the full, placed with him or
within the stipulated time limit, the E.M.D. of the supplier will be forfeited by the
Institution and the contract for the supply shall stand terminated with no further
liabilities on either party to the contract.
44. Bidders will be not allowed to withdraw from tenders after submission of
bids/opening of the tender.
45. All the firms participating in the Tender must submit a list of their owners/partners
etc. along with their contact telephone numbers and a Certificate to the effect that the
firm is neither blacklisted by any Government Department nor any Criminal Case is
registered against the firm or its owner or partners anywhere in India.
46. The bidder should also enclose a copy of their supply order to any Central / State
Government undertaking, if the same is available with him.
47. In the interest of institute, the Tender Inviting Authority reserved the right to
relax/withdraw any of the terms and conditions mentioned above so as to overcome
any problem encountered by the contracting parties
48. The right to accept or reject without assigning any reason any or all tenders in part or
whole is reserved with the Tender Inviting Authority and his decision (s) on all
matters relating to acceptance or rejection of the tenders as a whole or in part will be
final and binding to all.
49. Participation in tender will be Assumed that all terms and conditions are read and
accepted by bidder.
Sd/-(H. K. Patel)
Admin-cum-Accounts OfficerDr. APJ Abdul Kalam Govt. College
Silvassa
The above terms and conditions are accepted and are binding to me/us.Place:
Date: Signature of bidderName of the Bidder with seal of the firm
Note: Please return one copy of these terms and conditions duly signed with seal of thefirm alongwith tender.
Annexure-I
Specifications
Chemistry Lab-1
Sr.No DESCRIPTION Unit QTY.
1 TEACHER TABLE No. 1Size :-1550mm L x 650mm D x 750mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 2Nos
Size:- 450mm L x500mm D x 550mm H-Hanging Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
2 WORKING TABLE No. 2Size :-6350mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 6Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters Sink :- 3Nos
Size:-600mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 3Nos
v)Water Tap :- Three Way water Tap :- 3Nos
vi)Reagent Rack
Size:- 750mm L x 150mm D x730mm H :-2Nos
fitted of 01Nos 6/16Amp Switch Socket North-West Make
Size:- 1500mm L x 150mm D x730mm H :-2Nos
fitted of 02Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-6 Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
3 ISLAND TABLE No. 2Size :-6350mm L x 1500mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 12Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters Sink :- 6Nos
Size:-600mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 6Nos
v)Water Tap :- Three Way water Tap :- 6Nos
vi)Reagent Rack
Size:- 750mm L x 300mm D x730mm H :-2Nos
Both side fitted of 02Nos 6/16Amp Switch Socket North-West Make
Size:- 1500mm L x 300mm D x730mm H :-2Nos
Both side fitted of 04Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-12 Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
4 ISLAND TABLE No. 1Size :-5600mm L x 1500mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 10Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters Sink :- 6Nos
Size:-600mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 6Nos
v)Water Tap :- Three Way water Tap :- 6Nos
vi)Reagent Rack
Size:- 750mm L x 300mm D x730mm H :-1No
Both side fitted of 02Nos 6/16Amp Switch Socket North-West Make
Size:- 1500mm L x 300mm D x730mm H :-2Nos
Both side fitted of 04Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-10 Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
5Spot Extract System 75 Exhaust Arm75-9065-3-7-5 Ceiling Mounted 3 Joints,Reach:1550mm(Indian Make)
No.10.00
a P.P.Hood 385mm Dia No. 10.00
b Celing Colums No. 10.00
c Centrifugal Blower (0.75 HP) - Cluter 2Nos No. 1.00d Centrifugal Blower (1.5 HP) - Cluster 4Nos No. 2.00e Flexible Ducting Charges (Running Mtr) (4")75mmdia RMT 10.00
f PP Ducting Charges (Running Mtr)(6") 150mmdia RMT 35.00
Note:- TEST will be as per SEFA Guidelinesa. BCL Test : Verify that the cabinet is level. Load the cabinet top by using1500 lbs. of solid steelbars stacked five high and spaced After ten minutes, unloadthe cabinet.
b. BCCL Test : Using solid weights apply a total of 150 lbs. to the top of thecabinet along the cabinet centerlin. Operate doors and drawers.
c. BCT Test : Secure the cabinet diagonally from the unsupported corner withseven solid steel bars .1 (250 pounds (113.4 Kg) of weight), on the top of thecabinet to prevent overturning. Apply four solid steel bars (150 pounds [68.04Kg] of weight) to the unsupported corner for a period of fifteen minutes. Removeweight and place cabinet on the floor in its normal upright position. Observecabinet joinery. Level the cabinet and measure the face and back of the cabinetacross the diagonal corners.
d. BCDL Test : : Remove the shelf for this test. With unit and top set asdescribed in add sufficient weight to the top in order to prevent overturning. Withcabinet door opened 90- degrees, hang a sling made up of two 75 lbs. (shot bagsor solid weights) over top of the door at a point 8.5" (210.8mm) out from thehinge centerline Slowly move door through the full cycle of the hinge, up to a160- degree arc. Remove weight and swing door through its full intended range ofmotion and close door.
e. BCDI Test : With unit and top set as described in add sufficient weight tothe top in order to prevent overturning. A 20 lbs. sand bag shall be suspended anddropped to provide an impact of 240 inch-pounds (27.1 N-m)at the center of theclosed door.
f. BCDSL Test : (UDL 30 T0 40 Kg) With unit and top set add sufficientweight to the top in order toprevent overturning. Open the drawer to 13”(330.2mm) of travel and hang 113 lbs. from the drawer head at the centerline ofthe drawer for five minutes. Remove the weight and operate the drawer throughthe full cycle.
g. BCDDPHL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method. Blockdoor and drawer closed. Using a cable, pulley and weight assembly apply a forceof 50 lbs. perpendicular to each pull. Revise setup to hang weight from each pull.Remove weight.
h. BCDDPVL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method. Blockdoor and drawer closed. Using a cable, pulley and weight assembly apply a forceof 50 lbs. perpendicular to each pull. Revise setup to hang weight from each pull.Remove weight.i. BCDIRI Test : Position the drawer on a table at a 45-degree angle Place a40.mm diameter by 420mm long steel rod (approximately 10 lbs 13" (330.2mm)from the target impact area such that the rod will roll freely to impact the back ofthe drawer. Subject the back to three impacts and reverse the drawer to subject thefront to three additional impacts.
POWDER COATING TEST (As per SEFA/ASTM Guidlines
a. Pencil Hardness Test : With Test Certificate
b. Scratch Test : With Test Certificate
c. Micron Test : With Test Certificate
d. Impact Test : With Test Certificate
e. Tubular Impact Test : With Test Certificate
f. Erichen Cupping Test : With Test Certificate
g. Gloss Test : With Test Certificate
h. Cross Hatching Test : With Test Certificate
i. Salt Spray Test: 1000 hours salt spray test capability. With Test Certificate
j. Bend Test : With Test Certificate
k. Conical Mandrel Test : With Test Certificate
Colour Shade : Akzonoble WhitePantone Blue
Chemistry Lab-2
Sr.No DESCRIPTION Unit QTY.
1 TEACHER TABLE No. 1Size :-1550mm L x 650mm D x 750mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 2Nos
Size:- 450mm L x500mm D x 550mm H-Hanging Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
2 WORKING TABLE No. 2Size :-6350mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 6Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters Sink :- 3Nos
Size:-600mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 3Nos
v)Water Tap :- Three Way water Tap :- 3Nos
vi)Reagent Rack
Size:- 750mm L x 150mm D x730mm H :-2Nos
fitted of 01Nos 6/16Amp Switch Socket North-West Make
Size:- 1500mm L x 150mm D x730mm H :-2Nos
fitted of 02Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-6 Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
3 ISLAND TABLE No. 2Size :-6350mm L x 1500mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 12Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters Sink :- 6Nos
Size:-600mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 6Nos
v)Water Tap :- Three Way water Tap :- 6Nos
vi)Reagent Rack
Size:- 750mm L x 300mm D x730mm H :-2Nos
Both side fitted of 02Nos 6/16Amp Switch Socket North-West Make
Size:- 1500mm L x 300mm D x730mm H :-2Nos
Both side fitted of 04Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-12 Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
4 ISLAND TABLE No. 1Size :-5600mm L x 1500mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 10Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters Sink :- 6Nos
Size:-600mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 6Nos
v)Water Tap :- Three Way water Tap :- 6Nos
vi)Reagent Rack
Size:- 750mm L x 300mm D x730mm H :-1No
Both side fitted of 02Nos 6/16Amp Switch Socket North-West Make
Size:- 1500mm L x 300mm D x730mm H :-2Nos
Both side fitted of 04Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-10 Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
5Spot Extract System 75 Exhaust Arm75-9065-3-7-5 Ceiling Mounted 3 Joints,Reach:1550mm(Indian Make)
No.10.00
a P.P.Hood 385mm Dia No. 10.00
b Celing Colums No. 10.00
c Centrifugal Blower (0.75 HP) - Cluter 2Nos No. 1.00d Centrifugal Blower (1.5 HP) - Cluster 4Nos No. 2.00e Flexible Ducting Charges (Running Mtr) (4")75mmdia RMT 10.00
f PP Ducting Charges (Running Mtr)(6") 150mmdia RMT 35.00
Note:- TEST will be as per SEFA Guidelinesa. BCL Test : Verify that the cabinet is level. Load the cabinet top by using1500 lbs. of solid steelbars stacked five high and spaced After ten minutes, unloadthe cabinet.
b. BCCL Test : Using solid weights apply a total of 150 lbs. to the top of thecabinet along the cabinet centerlin. Operate doors and drawers.
c. BCT Test : Secure the cabinet diagonally from the unsupported corner withseven solid steel bars .1 (250 pounds (113.4 Kg) of weight), on the top of thecabinet to prevent overturning. Apply four solid steel bars (150 pounds [68.04Kg] of weight) to the unsupported corner for a period of fifteen minutes. Removeweight and place cabinet on the floor in its normal upright position. Observecabinet joinery. Level the cabinet and measure the face and back of the cabinetacross the diagonal corners.
d. BCDL Test : : Remove the shelf for this test. With unit and top set asdescribed in add sufficient weight to the top in order to prevent overturning. Withcabinet door opened 90- degrees, hang a sling made up of two 75 lbs. (shot bagsor solid weights) over top of the door at a point 8.5" (210.8mm) out from thehinge centerline Slowly move door through the full cycle of the hinge, up to a160- degree arc. Remove weight and swing door through its full intended range ofmotion and close door.
e. BCDI Test : With unit and top set as described in add sufficient weight tothe top in order to prevent overturning. A 20 lbs. sand bag shall be suspended anddropped to provide an impact of 240 inch-pounds (27.1 N-m)at the center of theclosed door.
f. BCDSL Test : (UDL 30 T0 40 Kg) With unit and top set add sufficientweight to the top in order toprevent overturning. Open the drawer to 13”(330.2mm) of travel and hang 113 lbs. from the drawer head at the centerline ofthe drawer for five minutes. Remove the weight and operate the drawer throughthe full cycle.
g. BCDDPHL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method. Blockdoor and drawer closed. Using a cable, pulley and weight assembly apply a forceof 50 lbs. perpendicular to each pull. Revise setup to hang weight from each pull.Remove weight.
h. BCDDPVL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method. Blockdoor and drawer closed. Using a cable, pulley and weight assembly apply a forceof 50 lbs. perpendicular to each pull. Revise setup to hang weight from each pull.Remove weight.i. BCDIRI Test : Position the drawer on a table at a 45-degree angle Place a40.mm diameter by 420mm long steel rod (approximately 10 lbs 13" (330.2mm)from the target impact area such that the rod will roll freely to impact the back ofthe drawer. Subject the back to three impacts and reverse the drawer to subject thefront to three additional impacts.
POWDER COATING TEST (As per SEFA/ASTM Guidlines
a. Pencil Hardness Test : With Test Certificate
b. Scratch Test : With Test Certificate
c. Micron Test : With Test Certificate
d. Impact Test : With Test Certificate
e. Tubular Impact Test : With Test Certificate
f. Erichen Cupping Test : With Test Certificate
g. Gloss Test : With Test Certificate
h. Cross Hatching Test : With Test Certificate
i. Salt Spray Test: 1000 hours salt spray test capability. With Test Certificate
j. Bend Test : With Test Certificate
k. Conical Mandrel Test : With Test Certificate
Colour Shade : Akzonoble WhitePantone Blue
Botany Laboratory
Sr.No DESCRIPTION Unit QTY.
1 TEACHER TABLE No. 1Size :-1550mm L x 650mm D x 750mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 2Nos
Size:- 450mm L x500mm D x 550mm H-Hanging Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
2 WORKING TABLE No. 1Size :-6050mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 4Nos
b) Two Shutters & One Shelf :- 4Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
vi)Reagent Rack
Size:- 1500mm L x 150mm D x730mm H :-4Nos
fitted of 02Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-8Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
3 WORKING TABLE No. 1Size :-4785mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 3Nos
Size:- 810mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters & One Shelf :- 1No
Size:- 750mm L x500mm D x 710mm H-Hanging Type
c) Two Shutters Sink :- 2Nos
Size:-750mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 2Nos
v)Water Tap :- Three Way water Tap :- 2Nos
vi)Reagent Rack
Size:- 810mm L x 150mm D x730mm H :-2Nos
fitted of 01Nos 6/16Amp Switch Socket North-West Make
Size:- 1560mm L x 150mm D x730mm H :-1No
fitted of 02Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-4Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
4 WORKING TABLE No. 1Size :-6050mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 4Nos
b) Two Shutters & One Shelf :- 4Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
vi)Reagent Rack
Size:- 1500mm L x 150mm D x730mm H :-2Nos
fitted of 02Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-8Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
5 ISLAND TABLE No. 1Size :-4550mm L x 1500mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 6Nos
b) Two Shutters & One Shelf :- 4Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters Sink :- 2Nos
Size:-750mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 2Nos
v)Water Tap :- Three Way water Tap :- 2Nos
vi)Reagent Rack
Size:- 750mm L x 300mm D x730mm H :-1No
Both side fitted of 02Nos 6/16Amp Switch Socket North-West Make
Size:- 1500mm L x 300mm D x730mm H :-2Nos
Both side fitted of 04Nos 6/16Amp Switch Socket North-West Make
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
NOTE:- TEST will be as per SEFA Guidelinesa. BCL Test : Verify that the cabinet is level. Load the cabinet top by using1500 lbs. of solid steelbars stacked five high and spaced After ten minutes, unloadthe cabinet.
b. BCCL Test : Using solid weights apply a total of 150 lbs. to the top of thecabinet along the cabinet centerlin. Operate doors and drawers.
c. BCT Test : Secure the cabinet diagonally from the unsupported corner withseven solid steel bars .1 (250 pounds (113.4 Kg) of weight), on the top of thecabinet to prevent overturning. Apply four solid steel bars (150 pounds [68.04Kg] of weight) to the unsupported corner for a period of fifteen minutes. Removeweight and place cabinet on the floor in its normal upright position. Observecabinet joinery. Level the cabinet and measure the face and back of the cabinetacross the diagonal corners.
d. BCDL Test : : Remove the shelf for this test. With unit and top set asdescribed in add sufficient weight to the top in order to prevent overturning. Withcabinet door opened 90- degrees, hang a sling made up of two 75 lbs. (shot bagsor solid weights) over top of the door at a point 8.5" (210.8mm) out from thehinge centerline Slowly move door through the full cycle of the hinge, up to a160- degree arc. Remove weight and swing door through its full intended range ofmotion and close door.
e. BCDI Test : With unit and top set as described in add sufficient weight tothe top in order to prevent overturning. A 20 lbs. sand bag shall be suspended anddropped to provide an impact of 240 inch-pounds (27.1 N-m)at the center of theclosed door.
f. BCDSL Test : (UDL 30 T0 40 Kg) With unit and top set add sufficientweight to the top in order toprevent overturning. Open the drawer to 13”(330.2mm) of travel and hang 113 lbs. from the drawer head at the centerline ofthe drawer for five minutes. Remove the weight and operate the drawer throughthe full cycle.
g. BCDDPHL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method. Blockdoor and drawer closed. Using a cable, pulley and weight assembly apply a forceof 50 lbs. perpendicular to each pull. Revise setup to hang weight from each pull.Remove weight.
h. BCDDPVL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method. Blockdoor and drawer closed. Using a cable, pulley and weight assembly apply a forceof 50 lbs. perpendicular to each pull. Revise setup to hang weight from each pull.Remove weight.i. BCDIRI Test : Position the drawer on a table at a 45-degree angle Place a40.mm diameter by 420mm long steel rod (approximately 10 lbs 13" (330.2mm)from the target impact area such that the rod will roll freely to impact the back ofthe drawer. Subject the back to three impacts and reverse the drawer to subject thefront to three additional impacts.
POWDER COATING TEST (As per SEFA/ASTM Guidlines
a. Pencil Hardness Test : With Test Certificate
b. Scratch Test : With Test Certificate
c. Micron Test : With Test Certificate
d. Impact Test : With Test Certificate
e. Tubular Impact Test : With Test Certificate
f. Erichen Cupping Test : With Test Certificate
g. Gloss Test : With Test Certificate
h. Cross Hatching Test : With Test Certificate
i. Salt Spray Test: 1000 hours salt spray test capability.With Test Certificate
j. Bend Test : With Test Certificate
k. Conical Mandrel Test : With Test Certificate
Colour Shade : Akzonoble WhitePantone Blue
Microbiology Lab -1
Sr.No DESCRIPTION Unit QTY.
1 TEACHER TABLE No. 1Size :-1550mm L x 650mm D x 750mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 2Nos
Size:- 450mm L x500mm D x 550mm H-Hanging Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
2 TEACHER TABLE No. 1Size :-1130mm L x 650mm D x 750mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 1No
Size:- 450mm L x500mm D x 550mm H-Hanging Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
3 WORKING TABLE No. 1Size :-2920mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Shutters & One Shelf :- 2Nos
Size:- 450mm L x500mm D x 710mm H-Hanging Type
b) One Drawer/Two Shutters & One Shelf :- 2Nos
Size:- 600mm L x500mm D x 710mm H-Hanging Type
c) Two Shutters Sink :- 1No
Size:-600mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 1No
v)Water Tap :- Three Way water Tap :- 1No
vi)Electric Trunking
Size:- 2100mm L x 100mm D x 100mm H :-1No
fitted of 04Nos 6/16Amp Switch Socket North-West Make
v)Two Way Gas Tap:-4 Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
4 CORNER SINK TABLE No. 3Size :-1050mm L x 1050mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a)One Shutters Corner Sink :- 1No
Size:-810mm+810mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 1No
v)Water Tap :- Three Way water Tap :- 1No
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
5 WORKING TABLE No. 1Size :-2435mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) Two Shutters & One Shelf :- 2Nos
b) One Drawer/Two Shutters & One Shelf :- 2Nos
Size:- 600mm L x500mm D x 710mm H-Hanging Type
iv)Electric Trunking
Size:- 2400mm L x 100mm D x 100mm H :-1No
fitted of 04Nos 6/16Amp Switch Socket North-West Make
v)Two Way Gas Tap:-4 Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
6 WORKING TABLE No. 1Size :-3775mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) Two Shutters & One Shelf :- 2Nos
b) One Drawer/Two Shutters & One Shelf :- 3Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
iv)Electric Trunking
Size:- 3750mm L x 100mm D x 100mm H :-1No
fitted of 05Nos 6/16Amp Switch Socket North-West Make
v)Two Way Gas Tap:-4 Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
7 ISLAND TABLE No. 1Size :-2425mm L x 1500mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 4Nos
b) Two Shutters & One Shelf :- 4Nos
Size:- 600mm L x500mm D x 710mm H-Hanging Type
iv)Reagent Rack
Size:- 1200mm L x 300mm D x730mm H :-2Nos
Both side fitted of 04Nos 6/16Amp Switch Socket North-West Make
v)Two Way Gas Tap:-8 Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
NOTE:- TEST will be as per SEFA Guidelinesa. BCL Test : Verify that the cabinet is level. Load the cabinet top by using1500 lbs. of solid steelbars stacked five high and spaced After ten minutes, unloadthe cabinet.
b. BCCL Test : Using solid weights apply a total of 150 lbs. to the top of thecabinet along the cabinet centerlin. Operate doors and drawers.
c. BCT Test : Secure the cabinet diagonally from the unsupported corner withseven solid steel bars .1 (250 pounds (113.4 Kg) of weight), on the top of thecabinet to prevent overturning. Apply four solid steel bars (150 pounds [68.04Kg] of weight) to the unsupported corner for a period of fifteen minutes. Removeweight and place cabinet on the floor in its normal upright position. Observecabinet joinery. Level the cabinet and measure the face and back of the cabinetacross the diagonal corners.
d. BCDL Test : : Remove the shelf for this test. With unit and top set asdescribed in add sufficient weight to the top in order to prevent overturning. Withcabinet door opened 90- degrees, hang a sling made up of two 75 lbs. (shot bagsor solid weights) over top of the door at a point 8.5" (210.8mm) out from thehinge centerline Slowly move door through the full cycle of the hinge, up to a160- degree arc. Remove weight and swing door through its full intended range ofmotion and close door.
e. BCDI Test : With unit and top set as described in add sufficient weight tothe top in order to prevent overturning. A 20 lbs. sand bag shall be suspended anddropped to provide an impact of 240 inch-pounds (27.1 N-m)at the center of theclosed door.
f. BCDSL Test : (UDL 30 T0 40 Kg) With unit and top set add sufficientweight to the top in order toprevent overturning. Open the drawer to 13”(330.2mm) of travel and hang 113 lbs. from the drawer head at the centerline ofthe drawer for five minutes. Remove the weight and operate the drawer throughthe full cycle.
g. BCDDPHL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method. Blockdoor and drawer closed. Using a cable, pulley and weight assembly apply a forceof 50 lbs. perpendicular to each pull. Revise setup to hang weight from each pull.Remove weight.
h. BCDDPVL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method. Blockdoor and drawer closed. Using a cable, pulley and weight assembly apply a forceof 50 lbs. perpendicular to each pull. Revise setup to hang weight from each pull.Remove weight.i. BCDIRI Test : Position the drawer on a table at a 45-degree angle Place a40.mm diameter by 420mm long steel rod (approximately 10 lbs 13" (330.2mm)from the target impact area such that the rod will roll freely to impact the back ofthe drawer. Subject the back to three impacts and reverse the drawer to subject thefront to three additional impacts.
POWDER COATING TEST (As per SEFA/ASTM Guidlines
a. Pencil Hardness Test : With Test Certificate
b. Scratch Test : With Test Certificate
c. Micron Test : With Test Certificate
d. Impact Test : With Test Certificate
e. Tubular Impact Test : With Test Certificate
f. Erichen Cupping Test : With Test Certificate
g. Gloss Test : With Test Certificate
h. Cross Hatching Test : With Test Certificate
i. Salt Spray Test: 1000 hours salt spray test capability.With Test Certificate
j. Bend Test : With Test Certificate
k. Conical Mandrel Test : With Test Certificate
Colour Shade : Akzonoble WhitePantone Blue
Microbiology Lab-2
Sr.No DESCRIPTION Unit QTY.
1 TEACHER TABLE No. 1Size :-1550mm L x 650mm D x 750mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 2Nos
Size:- 450mm L x500mm D x 550mm H-Hanging Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
2 TEACHER TABLE No. 1Size :-1130mm L x 650mm D x 750mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 1No
Size:- 450mm L x500mm D x 550mm H-Hanging Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
3 WORKING TABLE No. 1Size :-5400mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 3Nos
b) Two Shutters & One Shelf :- 2Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters Sink :- 2Nos
Size:-770mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 2Nos
v)Water Tap :- Three Way water Tap :- 2Nos
vi)Reagent Rack
Size:- 1450mm L x 150mm D x730mm H :-1No
side fitted of 02Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-5 Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
4 ISLAND TABLE No. 2Size :-4550mm L x 1500mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 6Nos
b) Two Shutters & One Shelf :- 4Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters Sink :- 2Nos
Size:-750mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 2Nos
v)Water Tap :- Three Way water Tap :- 2Nos
vi)Reagent Rack
Size:- 750mm L x 300mm D x730mm H :-1No
Both side fitted of 02Nos 6/16Amp Switch Socket North-West Make
Size:- 1500mm L x 300mm D x730mm H :-2Nos
Both side fitted of 04Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-5 Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
5 WORKING TABLE No. 1Size :-4870mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 3Nos
Size:- 830mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters & One Shelf :- 1No
Size:- 750mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters Sink :- 2Nos
Size:-750mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 2Nos
v)Water Tap :- Three Way water Tap :- 2Nos
vi)Reagent Rack
Size:- 830mm L x 150mm D x730mm H :-2Nos
side fitted of 02Nos 6/16Amp Switch Socket North-West Make
Size:- 1580mm L x 150mm D x730mm H :-1No
side fitted of 02Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-4Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
6 WORKING TABLE No. 1Size :-4785mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 2Nos
Size:- 825mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters & One Shelf :- 1No
c) One Drawer/Two Shutters & One Shelf :- 1No
Size:- 750mm L x500mm D x 710mm H-Hanging Type
d) Two Shutters Sink :- 2Nos
Size:-750mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 2Nos
v)Water Tap :- Three Way water Tap :- 2Nos
vi)Electric Trunking
Size:- 3175mm L x 100mm D x100mm H :-1No
fitted of 04Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-4Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
7 WORKING TABLE No. 2Size :-2600mm L x 650mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 3Nos
Size:- 450mm L x500mm D x 710mm H-Hanging Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
8 WORKING TABLE No. 1Size :-3050mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) Two Shutters & One Shelf :- 1No
b) One Drawer/Two Shutters & One Shelf :- 2Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
c) Two Shutters Sink :- 1No
Size:-750mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 1No
v)Water Tap :- Three Way water Tap :- 1No
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
9 CHEMICAL STORAGE with Ventilation NO 4Size :-1200mm L x 400mm D X 2100mm HMOC : 1.2mm-18g CRCA Sheet with epoxy powder coating
Internal lining eproxy of Phenolic resin for prevention against rust
4 nos. Adjustable Shelves of Polypropylene.
Two toughned glass doors with lock and key arrangement -
Each shelf must have 2 Nos. PP tray so total PP tray - 10 Nos.a PP Ducting Charges (Running feet) 8" (200mm) Rft 35b PP Ducting Charges (Running feet) 10" (250mm) Rft 15c Centrifugal Blower (0.5 HP) -1 No Cluster No. 2d Centrifugal Blower (0.75 HP) -2Nos cluster No. 1
NOTE:- TEST will be as per SEFA Guidelinesa. BCL Test : Verify that the cabinet is level. Load the cabinet top by using1500 lbs. of solid steelbars stacked five high and spaced After ten minutes, unloadthe cabinet.
b. BCCL Test : Using solid weights apply a total of 150 lbs. to the top of thecabinet along the cabinet centerlin. Operate doors and drawers.
c. BCT Test : Secure the cabinet diagonally from the unsupported corner withseven solid steel bars .1 (250 pounds (113.4 Kg) of weight), on the top of thecabinet to prevent overturning. Apply four solid steel bars (150 pounds [68.04Kg] of weight) to the unsupported corner for a period of fifteen minutes. Removeweight and place cabinet on the floor in its normal upright position. Observecabinet joinery. Level the cabinet and measure the face and back of the cabinetacross the diagonal corners.
d. BCDL Test : : Remove the shelf for this test. With unit and top set asdescribed in add sufficient weight to the top in order to prevent overturning. Withcabinet door opened 90- degrees, hang a sling made up of two 75 lbs. (shot bagsor solid weights) over top of the door at a point 8.5" (210.8mm) out from thehinge centerline Slowly move door through the full cycle of the hinge, up to a160- degree arc. Remove weight and swing door through its full intended range ofmotion and close door.
e. BCDI Test : With unit and top set as described in add sufficient weight tothe top in order to prevent overturning. A 20 lbs. sand bag shall be suspended anddropped to provide an impact of 240 inch-pounds (27.1 N-m)at the center of theclosed door.
f. BCDSL Test : (UDL 30 T0 40 Kg) With unit and top set add sufficientweight to the top in order toprevent overturning. Open the drawer to 13”(330.2mm) of travel and hang 113 lbs. from the drawer head at the centerline ofthe drawer for five minutes. Remove the weight and operate the drawer throughthe full cycle.
g. BCDDPHL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method. Blockdoor and drawer closed. Using a cable, pulley and weight assembly apply a forceof 50 lbs. perpendicular to each pull. Revise setup to hang weight from each pull.Remove weight.
h. BCDDPVL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method. Blockdoor and drawer closed. Using a cable, pulley and weight assembly apply a forceof 50 lbs. perpendicular to each pull. Revise setup to hang weight from each pull.Remove weight.i. BCDIRI Test : Position the drawer on a table at a 45-degree angle Place a40.mm diameter by 420mm long steel rod (approximately 10 lbs 13" (330.2mm)from the target impact area such that the rod will roll freely to impact the back ofthe drawer. Subject the back to three impacts and reverse the drawer to subject thefront to three additional impacts.
POWDER COATING TEST (As per SEFA/ASTM Guidlines
a. Pencil Hardness Test : With Test Certificate
b. Scratch Test : With Test Certificate
c. Micron Test : With Test Certificate
d. Impact Test : With Test Certificate
e. Tubular Impact Test : With Test Certificate
f. Erichen Cupping Test : With Test Certificate
g. Gloss Test : With Test Certificate
h. Cross Hatching Test : With Test Certificate
i. Salt Spray Test: 1000 hours salt spray test capability. With Test Certificate
j. Bend Test : With Test Certificate
k. Conical Mandrel Test : With Test Certificate
Colour Shade : Akzonoble WhitePantone Blue
Physics Lab.
Sr.No DESCRIPTION Unit QTY.
1 TEACHER TABLE No. 1Size :-1550mm L x 650mm D x 750mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 2Nos
Size:- 450mm L x500mm D x 550mm H-Hanging Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
2 TEACHER TABLE No. 1Size :-1130mm L x 650mm D x 750mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 1No
Size:- 450mm L x500mm D x 550mm H-Hanging Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
3 WORKING TABLE No. 1Size :-4885mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 1No
b)Two Shutters & One Shelf :- 2Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
c) One Drawer/Two Shutters & One Shelf :- 2Nos
Size:- 875mm L x500mm D x 710mm H-Hanging Type
d) Two Shutters Sink :- 1No
Size:-750mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 1No
v)Water Tap :- Three Way water Tap :- 1No
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
4 WORKING TABLE No. 1Size :-4815mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 1No
b)Two Shutters & One Shelf :- 3Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
c) One Drawer/Two Shutters & One Shelf :- 2Nos
Size:- 875mm L x500mm D x 710mm H-Hanging Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
5 CENTER TABLE No. 2Size :-6050mm L x 1500mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :-8Nos
b)Two Shutters & One Shelf :- 8Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
iv)Electric Trunking
Size:- 6000mm L x 100mm D x 100mm H :-2Nos
fitted of 8Nos 6/16Amp Switch Socket North-West Make
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
6 STORAGE RACK No. 2Size :- 1000mm Lx 450mm Dx 1800+150mm H
With Two Horizantal Campartment . Each Campartment
3 Nos Of Adjustable Shelf Total Shelf 6 Nos & 1 No is
fix type .MOC:-20 G CRCA Sheet With Powder coated. Open Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
7 WORK TABLE No. 1Size :-1600mm L x 1000mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)Granite Support Frame 60x30mm Sq.tube Powder coating
Size:- 1550mm L x950mm D x 870mm H
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
8 CENTER TABLE No. 4Size :-2150mm L x 1500mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillageproof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :-2Nos
Size:- 900mm L x500mm D x 710mm H-Hanging Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar andequivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawer frontis with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noisewhile closing the shutter the entire module is made up of CRCA Sheets and areWelded is high sturdy. Able to take load up to 1500 lbs Capacity per Base Cabinetand hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
NOTE:- TEST will be as per SEFA Guidelinesa. BCL Test : Verify that the cabinet is level. Load the cabinet top by using1500 lbs. of solid steelbars stacked five high and spaced After ten minutes, unloadthe cabinet.
b. BCCL Test : Using solid weights apply a total of 150 lbs. to the top of thecabinet along the cabinet centerlin. Operate doors and drawers.
c. BCT Test : Secure the cabinet diagonally from the unsupported corner withseven solid steel bars .1 (250 pounds (113.4 Kg) of weight), on the top of thecabinet to prevent overturning. Apply four solid steel bars (150 pounds [68.04Kg] of weight) to the unsupported corner for a period of fifteen minutes. Removeweight and place cabinet on the floor in its normal upright position. Observecabinet joinery. Level the cabinet and measure the face and back of the cabinetacross the diagonal corners.
d. BCDL Test : : Remove the shelf for this test. With unit and top set asdescribed in add sufficient weight to the top in order to prevent overturning. Withcabinet door opened 90- degrees, hang a sling made up of two 75 lbs. (shot bagsor solid weights) over top of the door at a point 8.5" (210.8mm) out from thehinge centerline Slowly move door through the full cycle of the hinge, up to a160- degree arc. Remove weight and swing door through its full intended range ofmotion and close door.
e. BCDI Test : With unit and top set as described in add sufficient weight tothe top in order to prevent overturning. A 20 lbs. sand bag shall be suspended anddropped to provide an impact of 240 inch-pounds (27.1 N-m)at the center of theclosed door.
f. BCDSL Test : (UDL 30 T0 40 Kg) With unit and top set add sufficientweight to the top in order toprevent overturning. Open the drawer to 13”(330.2mm) of travel and hang 113 lbs. from the drawer head at the centerline ofthe drawer for five minutes. Remove the weight and operate the drawer throughthe full cycle.
g. BCDDPHL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method. Blockdoor and drawer closed. Using a cable, pulley and weight assembly apply a forceof 50 lbs. perpendicular to each pull. Revise setup to hang weight from each pull.Remove weight.
h. BCDDPVL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method. Blockdoor and drawer closed. Using a cable, pulley and weight assembly apply a forceof 50 lbs. perpendicular to each pull. Revise setup to hang weight from each pull.Remove weight.i. BCDIRI Test : Position the drawer on a table at a 45-degree angle Place a40.mm diameter by 420mm long steel rod (approximately 10 lbs 13" (330.2mm)from the target impact area such that the rod will roll freely to impact the back ofthe drawer. Subject the back to three impacts and reverse the drawer to subject thefront to three additional impacts.
POWDER COATING TEST (As per SEFA/ASTM Guidlines
a. Pencil Hardness Test : With Test Certificate
b. Scratch Test : With Test Certificate
c. Micron Test : With Test Certificate
d. Impact Test : With Test Certificate
e. Tubular Impact Test : With Test Certificate
f. Erichen Cupping Test : With Test Certificate
g. Gloss Test : With Test Certificate
h. Cross Hatching Test : With Test Certificate
i. Salt Spray Test: 1000 hours salt spray test capability.With Test Certificate
j. Bend Test : With Test Certificate
k. Conical Mandrel Test : With Test Certificate
Colour Shade : Akzonoble WhitePantone Blue
Mathematics Laboratory
Sr.No DESCRIPTION Unit QTY.
1 TEACHER TABLE No. 1Size :-1550mm L x 650mm D x 750mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash andspillage proof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 2Nos
Size:- 450mm L x500mm D x 550mm H-Hanging Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essarand equivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawerfront is with sandwich construction. Shutter Gaps is filled up with foam sheet[16mm Thick] & Noise proof Foam Tape [3mm Thick]. This will minimizebanging noise while closing the shutter the entire module is made up ofCRCA Sheets and are Welded is high sturdy. Able to take load up to 1500lbs Capacity per Base Cabinet and hardware S.S. hinges And Godrej andequivalent Multipurpose Lock.
2 CENTER TABLE No. 2Size :-5300mm L x 1350mm D x 750mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash andspillage proof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 10Nos
Size:- 450mm L x500mm D x 710mm H-Hanging Type
iv)Electric Trunking
Size:- 5250mm L x 100mm D x 100mm H :-2Nos
fitted of 7Nos 6/16Amp Switch Socket and Data point North-West Make
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essarand equivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawerfront is with sandwich construction. Shutter Gaps is filled up with foam sheet[16mm Thick] & Noise proof Foam Tape [3mm Thick]. This will minimizebanging noise while closing the shutter the entire module is made up ofCRCA Sheets and are Welded is high sturdy. Able to take load up to 1500lbs Capacity per Base Cabinet and hardware S.S. hinges And Godrej andequivalent Multipurpose Lock.
3 STORAGE RACK No. 1Size :- 1000mm Lx 450mm Dx 1800+150mm H
With Two Horizantal Campartment . Each Campartment
3 Nos Of Adjustable Shelf Total Shelf 6 Nos & 1 No is
fix type .MOC:-20 G CRCA Sheet With Powder coated. Open Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essarand equivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawerfront is with sandwich construction. Shutter Gaps is filled up with foam sheet[16mm Thick] & Noise proof Foam Tape [3mm Thick]. This will minimizebanging noise while closing the shutter the entire module is made up ofCRCA Sheets and are Welded is high sturdy. Able to take load up to 1500lbs Capacity per Base Cabinet and hardware S.S. hinges And Godrej andequivalent Multipurpose Lock.
NOTE:- TEST will be as per SEFA Guidelinesa. BCL Test : Verify that the cabinet is level. Load the cabinet top byusing 1500 lbs. of solid steelbars stacked five high and spaced After tenminutes, unload the cabinet.
b. BCCL Test : Using solid weights apply a total of 150 lbs. to the top ofthe cabinet along the cabinet centerlin. Operate doors and drawers.
c. BCT Test : Secure the cabinet diagonally from the unsupported cornerwith seven solid steel bars .1 (250 pounds (113.4 Kg) of weight), on the top ofthe cabinet to prevent overturning. Apply four solid steel bars (150 pounds[68.04 Kg] of weight) to the unsupported corner for a period of fifteenminutes. Remove weight and place cabinet on the floor in its normal uprightposition. Observe cabinet joinery. Level the cabinet and measure the face andback of the cabinet across the diagonal corners.
d. BCDL Test : : Remove the shelf for this test. With unit and top set asdescribed in add sufficient weight to the top in order to prevent overturning.With cabinet door opened 90- degrees, hang a sling made up of two 75 lbs.(shot bags or solid weights) over top of the door at a point 8.5" (210.8mm)out from the hinge centerline Slowly move door through the full cycle of thehinge, up to a 160- degree arc. Remove weight and swing door through its fullintended range of motion and close door.
e. BCDI Test : With unit and top set as described in add sufficient weightto the top in order to prevent overturning. A 20 lbs. sand bag shall besuspended and dropped to provide an impact of 240 inch-pounds (27.1 N-m)at the center of the closed door.
f. BCDSL Test : (UDL 30 T0 40 Kg) With unit and top set add sufficientweight to the top in order toprevent overturning. Open the drawer to 13”(330.2mm) of travel and hang 113 lbs. from the drawer head at the centerlineof the drawer for five minutes. Remove the weight and operate the drawerthrough the full cycle.
g. BCDDPHL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method.Block door and drawer closed. Using a cable, pulley and weight assemblyapply a force of 50 lbs. perpendicular to each pull. Revise setup to hangweight from each pull. Remove weight.
h. BCDDPVL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method.Block door and drawer closed. Using a cable, pulley and weight assemblyapply a force of 50 lbs. perpendicular to each pull. Revise setup to hangweight from each pull. Remove weight.i. BCDIRI Test : Position the drawer on a table at a 45-degree anglePlace a 40.mm diameter by 420mm long steel rod (approximately 10 lbs 13"(330.2mm) from the target impact area such that the rod will roll freely toimpact the back of the drawer. Subject the back to three impacts and reversethe drawer to subject the front to three additional impacts.
POWDER COATING TEST (As per SEFA/ASTM Guidlines
a. Pencil Hardness Test : With Test Certificate
b. Scratch Test : With Test Certificate
c. Micron Test : With Test Certificate
d. Impact Test : With Test Certificate
e. Tubular Impact Test : With Test Certificate
f. Erichen Cupping Test : With Test Certificate
g. Gloss Test : With Test Certificate
h. Cross Hatching Test : With Test Certificatei. Salt Spray Test: 1000 hours salt spray test capability.With TestCertificate
j. Bend Test : With Test Certificate
k. Conical Mandrel Test : With Test Certificate
Colour Shade : Akzonoble WhitePantone Blue
Central Instrumentation Laboratory
Sr.No DESCRIPTION Unit QTY.
1 TEACHER TABLE No. 1Size :-1550mm L x 650mm D x 750mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash andspillage proof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 2Nos
Size:- 450mm L x500mm D x 550mm H-Hanging Type
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essarand equivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawerfront is with sandwich construction. Shutter Gaps is filled up with foam sheet[16mm Thick] & Noise proof Foam Tape [3mm Thick]. This will minimizebanging noise while closing the shutter the entire module is made up ofCRCA Sheets and are Welded is high sturdy. Able to take load up to 1500lbs Capacity per Base Cabinet and hardware S.S. hinges And Godrej andequivalent Multipurpose Lock.
2 WORKING TABLE No. 1Size :-6350mm L x 750mm D x 900mm HSize :-5465mm L x 750mm D x 900mm HSize :-6350mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash andspillage proof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 2Nos
Size:- 420mm L x500mm D x 710mm H-Hanging Type
b) One Drawer/One Shutters & One Shelf :- 12Nos
Size:- 450mm L x500mm D x 710mm H-Hanging Type
d) Two Shutters Sink :- 2Nos
Size:-650mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 2Nos
v)Water Tap :- Three Way water Tap :- 2Nos
vi)Electric Trunking
Size:- 6325mm+2640mm+6325mm L x 100mm D x100mm H :-1No
fitted of 43Nos 6/16Amp Switch Socket North-West Make
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essarand equivalent makes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawerfront is with sandwich construction. Shutter Gaps is filled up with foam sheet[16mm Thick] & Noise proof Foam Tape [3mm Thick]. This will minimizebanging noise while closing the shutter the entire module is made up ofCRCA Sheets and are Welded is high sturdy. Able to take load up to 1500lbs Capacity per Base Cabinet and hardware S.S. hinges And Godrej andequivalent Multipurpose Lock.
3 WORKING CENTER TABLE No. 1Size :-4250mm L x 1500mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash andspillage proof dished granite worktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/One Shutters & One Shelf :- 08Nos
Size:- 450mm L x500mm D x710mm H-Hanging Type
iv)Electric Trunking
Size:- 4200mm L x 100mm D x 100mm H :-2Nos
fitted of 12Nos 6/16Amp Switch Socket North-West Make
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essarand equivalentmakes Cold Rolled Close Annealed [CRCA] Sheet. [With Testcertificate] completely made in 0.8 mm CRCA sheets. The shutter & drawerfront is with sandwich construction. Shutter Gaps is filled up with foam sheet[16mm Thick] & Noise proof Foam Tape [3mm Thick]. This will minimizebanging noise while closing the shutter the entire module is made up ofCRCA Sheets and are Welded is high sturdy. Able to take load up to 1500lbs Capacity per Base Cabinet and hardware S.S. hinges And Godrej andequivalent Multipurpose Lock.
Note:- TEST will be as per SEFA Guidelinesa. BCL Test : Verify that the cabinet is level. Load the cabinet top byusing 1500 lbs. of solid steelbars stacked five high and spaced After tenminutes, unload the cabinet.
b. BCCL Test : Using solid weights apply a total of 150 lbs. to the top ofthe cabinet along the cabinet centerlin. Operate doors and drawers.
c. BCT Test : Secure the cabinet diagonally from the unsupported cornerwith seven solid steel bars .1 (250 pounds (113.4 Kg) of weight), on the top ofthe cabinet to prevent overturning. Apply four solid steel bars (150 pounds[68.04 Kg] of weight) to the unsupported corner for a period of fifteenminutes. Remove weight and place cabinet on the floor in its normal uprightposition. Observe cabinet joinery. Level the cabinet and measure the face andback of the cabinet across the diagonal corners.
d. BCDL Test : : Remove the shelf for this test. With unit and top set asdescribed in add sufficient weight to the top in order to prevent overturning.With cabinet door opened 90- degrees, hang a sling made up of two 75 lbs.(shot bags or solid weights) over top of the door at a point 8.5" (210.8mm)out from the hinge centerline Slowly move door through the full cycle of thehinge, up to a 160- degree arc. Remove weight and swing door through its fullintended range of motion and close door.
e. BCDI Test : With unit and top set as described in add sufficient weightto the top in order to prevent overturning. A 20 lbs. sand bag shall besuspended and dropped to provide an impact of 240 inch-pounds (27.1 N-m)at the center of the closed door.
f. BCDSL Test : (UDL 30 T0 40 Kg) With unit and top set add sufficientweight to the top in order toprevent overturning. Open the drawer to 13”(330.2mm) of travel and hang 113 lbs. from the drawer head at the centerlineof the drawer for five minutes. Remove the weight and operate the drawerthrough the full cycle.
g. BCDDPHL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method.Block door and drawer closed. Using a cable, pulley and weight assemblyapply a force of 50 lbs. perpendicular to each pull. Revise setup to hangweight from each pull. Remove weight.
h. BCDDPVL Test : Pulls are to be installed in accordance withmanufacturer’s practice using specified attaching hardware and method.Block door and drawer closed. Using a cable, pulley and weight assemblyapply a force of 50 lbs. perpendicular to each pull. Revise setup to hangweight from each pull. Remove weight.i. BCDIRI Test : Position the drawer on a table at a 45-degree anglePlace a 40.mm diameter by 420mm long steel rod (approximately 10 lbs 13"(330.2mm) from the target impact area such that the rod will roll freely toimpact the back of the drawer. Subject the back to three impacts and reversethe drawer to subject the front to three additional impacts.
POWDER COATING TEST (As per SEFA/ASTM Guidlines
a. Pencil Hardness Test : With Test Certificate
b. Scratch Test : With Test Certificate
c. Micron Test : With Test Certificate
d. Impact Test : With Test Certificate
e. Tubular Impact Test : With Test Certificate
f. Erichen Cupping Test : With Test Certificate
g. Gloss Test : With Test Certificate
h. Cross Hatching Test : With Test Certificatei. Salt Spray Test: 1000 hours salt spray test capability.With TestCertificate
j. Bend Test : With Test Certificate
k. Conical Mandrel Test : With Test Certificate
Colour Shade : Akzonoble WhitePantone Blue
Annexure-II
1. WORKING TABLESize :-6350mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillage proof dished graniteworktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 6Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters Sink :- 3Nos
Size:-600mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 3Nos
v)Water Tap :- Three Way water Tap :- 3Nos
vi)Reagent Rack
Size:- 750mm L x 150mm D x730mm H :-2Nos
fitted of 01Nos 6/16Amp Switch Socket North-West Make
Size:- 1500mm L x 150mm D x730mm H :-2Nos
fitted of 02Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-6 Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar and equivalent makes ColdRolled Close Annealed [CRCA] Sheet. [With Test certificate] completely made in 0.8 mm CRCA sheets.The shutter & drawer front is with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noise while closing the shutterthe entire module is made up of CRCA Sheets and are Welded is high sturdy. Able to take load up to 1500lbs Capacity per Base Cabinet and hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
2. ISLAND TABLESize :-6350mm L x 1500mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillage proof dished graniteworktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
a) One Drawer/Two Shutters & One Shelf :- 12Nos
Size:- 750mm L x500mm D x 710mm H-Hanging Type
b) Two Shutters Sink :- 6Nos
Size:-600mm L x 500mm D x 710mm H-Hanging Type
iv) Sink:-PP Sink 570mmx355mm Approx :- 6Nos
v)Water Tap :- Three Way water Tap :- 6Nos
vi)Reagent Rack
Size:- 750mm L x 300mm D x730mm H :-2Nos
Both side fitted of 02Nos 6/16Amp Switch Socket North-West Make
Size:- 1500mm L x 300mm D x730mm H :-2Nos
Both side fitted of 04Nos 6/16Amp Switch Socket North-West Make
vii)Two Way Gas Tap:-12 Nos
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar and equivalent makes ColdRolled Close Annealed [CRCA] Sheet. [With Test certificate] completely made in 0.8 mm CRCA sheets.The shutter & drawer front is with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noise while closing the shutterthe entire module is made up of CRCA Sheets and are Welded is high sturdy. Able to take load up to 1500lbs Capacity per Base Cabinet and hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
3. WORKING TABLESize :-6350mm L x 750mm D x 900mm H
Consisting of following itemes
i) Table Top:- Epoxy Coated Black Granite Chemical resistant splash and spillage proof dished graniteworktop 18 mm to 20mm of thickness
ii)"C"Frame 60x30mm Sq.tube Powder coating
iii)Under Bench Storage Unit:-
b) One Drawer/One Shutters & One Shelf :-06Nos
Size:- 450mm L x500mm D x 710mm H-Hanging Type
vi)Electric Trunking
Size:- 6325mmx 100mm D x100mm H :-1No
fitted of 18Nos 6/16Amp Switch Socket North-West Make
STORAGE MODULE MATERIAL OF CONSTRUCTION : TATA, Essar and equivalent makes ColdRolled Close Annealed [CRCA] Sheet. [With Test certificate] completely made in 0.8 mm CRCA sheets.The shutter & drawer front is with sandwich construction. Shutter Gaps is filled up with foam sheet [16mmThick] & Noise proof Foam Tape [3mm Thick]. This will minimize banging noise while closing the shutterthe entire module is made up of CRCA Sheets and are Welded is high sturdy. Able to take load up to 1500lbs Capacity per Base Cabinet and hardware S.S. hinges And Godrej and equivalent Multipurpose Lock.
Annexure-III
Tender Document for supply of Worktables and other materials for ScienceLaboratories of Dr. APJ Abdul Kalam Govt. College, Silvassa.
Tender Notice No: EDN/SC/SCI LAB/NCB/2015/394/17 Date: 27/11/2015
TECHNICAL BID
1. Name of the Tenderer
2. Address of the Tenderer
3. Copy of Licence / ManufactureLicence No. issued by CompetentAuthority
4. E-mail
5. Tel. Nos./Cell Nos.
6. Name of the Proprioter/Partners
7. Year of Establishment
8. Tender Fee (Demand Draft No;Date & Bank Name)
9. EMD (Demand Draft No; Date &Bank Name)
10. CST or VAT No.
11. Excise and Service Tax
12. PAN No.
13. Last 03 years IT Return.
(i.e. 2013-14, 2012-13, 2011-12)
14. Annual Turnover of not less than 5crore for last 02 years. (CACertified)
15. Bank Account No; Bank Name,Branch Name & IFSC Code
16. Terms and Conditions Signed byAuthorised person with stamp
17. Physical Sample of Table (Date &Time)
I / We certify that I / We read, understood and accept the contents of both terms andconditions incorporated in the Tender Form and ‘Note’ below and submit this Tender forconsideration. I / We certify that the above statements are true.
(Signature of the Owner/Proprietor) with stamp
Full name of the Firm:
Address:
List of Copies to be submitted compulsory with the Technical Bid
1. Copy of Manufacturing Licence/ Trade Licence from Competent Authority
2. Copy of Tender Fee Receipt
3. Copy of EMD
3. Copy of PAN No.
4. Copy of Service Tax OR VAT No.
5. Copy of Excise Registration
6. Copy of 03 years IT Return (i.e. 2013-14, 2012-13, 2011-12)
7. Copy of Annual Turnover of not less than 5 crore for last 02 years. (CA Certified)
8. Copy of Terms & Conditions Signed by Authorised person with stamp.
9. Physical actual sample of Table
Sd/-(Shri H. K. Patel)
Admin-cum-Accounts Officer,Dr. APJ Abdul Kalam Govt. College
Silvassa
Rate Schedule
Sr.No DESCRIPTION Unit QTY. RATE PERUNIT
TOTALAMOUNT
A CHEMISTRY LAB-1
1 TEACHER TABLE Size :-1550mm L x 650mm D x750mm H No. 1
2 WORKING TABLE Size :-6350mm L x 750mm D x900mm H No. 2
3 ISLAND TABLE Size :-6350mm L x 1500mm D x900mm H No. 2
4 ISLAND TABLE Size :-5600mm L x 1500mm D x900mm H No. 1
5Spot Extract System 75 Exhaust Arm 75-9065-3-7-5Ceiling Mounted 3 Joints,Reach:1550mm(IndianMake) No. 10
a P.P.Hood 385mm Dia No. 10b Celing Colums No. 10c Centrifugal Blower (0.75 HP) - Cluter 2Nos No. 1d Centrifugal Blower (1.5 HP) - Cluster 4Nos No. 2e Flexible Ducting Charges (Running Mtr) (4")75mmdia RMT 10f PP Ducting Charges (Running Mtr)(6") 150mmdia RMT 35B CHEMISTRY LAB-2
1 TEACHER TABLE Size :-1550mm L x 650mm D x750mm H No. 1
2 WORKING TABLE Size :-6350mm L x 750mm D x900mm H No. 2
3 ISLAND TABLE Size :-6350mm L x 1500mm D x900mm H No. 2
4 ISLAND TABLE Size :-5600mm L x 1500mm D x900mm H No. 1
5Spot Extract System 75 Exhaust Arm 75-9065-3-7-5Ceiling Mounted 3 Joints,Reach:1550mm(IndianMake) No. 10
a P.P.Hood 385mm Dia No. 10b Celing Colums No. 10c Centrifugal Blower (0.75 HP) - Cluter 2Nos No. 1d Centrifugal Blower (1.5 HP) - Cluster 4Nos No. 2e Flexible Ducting Charges (Running Mtr) (4")75mmdia RMT 10f PP Ducting Charges (Running Mtr)(6") 150mmdia RMT 35
C MICROBIOLOGY LAB-1
1 TEACHER TABLE Size :-1550mm L x 650mm D x750mm H No. 1
2 TEACHER TABLE Size :-1130mm L x 650mm D x750mm H No. 1
3 WORKING TABLE Size :-2920mm L x 750mm D x900mm H No. 1
4 CORNER SINK TABLE Size :-1050mm L x 1050mm Dx 900mm H No. 3
5 WORKING TABLE Size :-2435mm L x 750mm D x900mm H No. 1
6 WORKING TABLE Size :-3775mm L x 750mm D x900mm H No. 1
7 ISLAND TABLE Size :-2425mm L x 1500mm D x900mm H No. 1
D MICROBIOLOGY LAB-2
1 TEACHER TABLE Size :-1550mm L x 650mm D x750mm H No. 1
2 TEACHER TABLE Size :-1130mm L x 650mm D x750mm H No. 1
3 WORKING TABLE Size :-5400mm L x 750mm D x900mm H No. 1
4 ISLAND TABLE Size :-4550mm L x 1500mm D x900mm H No. 2
5 WORKING TABLE Size :-4870mm L x 750mm D x900mm H No. 1
6 WORKING TABLE Size :-4785mm L x 750mm D x900mm H No. 1
7 WORKING TABLE Size :-2600mm L x 650mm D x900mm H No. 2
8 WORKING TABLE Size :-3050mm L x 750mm D x900mm H No. 1
9 CHEMICAL STORAGE with Ventilation Size :-1200mm L x 400mm D X 2100mm H NO 4
a PP Ducting Charges (Running feet) 8" (200mm) Rft 35b PP Ducting Charges (Running feet) 10" (250mm) Rft 15c Centrifugal Blower (0.5 HP) -1 No Cluster No. 2d Centrifugal Blower (0.75 HP) -2Nos cluster No. 1
E CETRAL INSTRUMENTATION LAB
1 TEACHER TABLE Size :-1550mm L x 650mm D x750mm H No. 1
2
WORKING TABLE Size :-6350mm L x 750mm D x900mm H WORKING TABLESize :-5465mm L x 750mm D x 900mm H WORKINGTABLE Size :-6350mm L x 750mm D x 900mm H No. 1
3 WORKING CENTER TABLE Size :-4250mm L x1500mm D x 900mm H No. 1
F PHYSICS LAB
1 TEACHER TABLE Size :-1550mm L x 650mm D x750mm H No. 1
2 TEACHER TABLE Size :-1130mm L x 650mm D x750mm H No. 1
3 WORKING TABLE Size :-4885mm L x 750mm D x900mm H No. 1
4 WORKING TABLE Size :-4815mm L x 750mm D x900mm H No. 1
5 CENTER TABLE Size :-6050mm L x 1500mm D x900mm H No. 2
6 STORAGE RACK Size :- 1000mm Lx 450mm Dx1800+150mm H No. 2
7 WORK TABLE Size :-1600mm L x 1000mm D x900mm H No. 1
8 CENTER TABLE Size :-2150mm L x 1500mm D x900mm H No. 4
G MATHEMATICS LAB
1 TEACHER TABLE Size :-1550mm L x 650mm D x750mm H No. 1
2 CENTER TABLE Size :-5300mm L x 1350mm D x750mm H No. 2
3 STORAGE RACK Size :- 1000mm Lx 450mm Dx1800+150mm H No. 1
H BOTANY LAB
1 TEACHER TABLE Size :-1550mm L x 650mm D x750mm H No. 1
2 WORKING TABL ESize :-6050mm L x 750mm D x900mm H No. 1
3 WORKING TABLE Size :-4785mm L x 750mm D x900mm H No. 1
4 WORKING TABLE Size :-6050mm L x 750mm D x900mm H No. 1
5 ISLAND TABLE Size :-4550mm L x 1500mm D x900mm H No. 1
GRAND TOTAL (A to H)
NOTE:- Lowest bidder of grand totalwill be consider