Download the complete KNIPEX Catalog
Transcript of Download the complete KNIPEX Catalog
GENEral CataloG 2013
KN
IPEX
– G
ENEr
al
Cata
loG
201
3
flat jaws
half-round jaws
round jaws
PlIErs aBC tEChNICal BasICs
Cutting Pliersfor cutting or nipping (diagonal, center and end cutters, carpenters‘ pincers etc.)
Gripping Pliers(flat-, long-nose and water pump pliers etc.)
Combined Pliersfor cutting and gripping (combination, stork beak and radio pliers etc.)
Special Pliersfor special applications, e.g. notching or punching different types of materials (sheet-metal nibbler, tile nibbling pincers etc.)
point
gripping surface
recess (pipe grip)
jaw
flank
additional cutting edge
BasIC shaPEs of thE jaws
joINt CoNNECtIoNs
tyPEs of joINts
Forged-in joint axleThe rivet is part of one handle(forged from one piece) high stability to withstand
highest strain long service life
Joint with inserted rivetA proved, sturdy and precise rivet connection for all standard pliers.
Bolted jointFor particularly demanding requi-rements in terms of precision and smooth operation, e.g. in circlip pliers and cable shears (even the finest multi-stranded conductors have to be cut cleanly).
Lap jointThe two pliers halves lie on top of each other but are not milled out.
Single jointHalf the thickness in each pliers handle is milled away in the joint area so that both handles can be laid into each other.
Box jointOne handle on the pliers is slit. The other handle is pushed through this slot. This joint connection can withstand a high level of load and strain because the joint bolt is supported on both sides and the inside handle is guided on both sides.
flat jaws
half-round jaws
round jaws
flat and pointed jaws
box joint
bolted joint
smooth gripping surfaces
serrated gripping surfaces
cross-hatched, knurled gripping surfaces
with opening spring
with lead catcher
angle
electrostatic discharging, dissipative
electronics
VDE tested, also in conformance to GPSG (Equipment and Product Safety Act)
insulated according to IEC 60900 / ASTM F1505, usable up to 1000 V AC/1500 V DCinsulated according to DIN VDE 0680/1, suitable for the application up to 1000 V AC / 1500 V DC
conforms to a European directive
mechanically tested in accordance with the equipment and product safety act
WEEE marking (Waste Electrical and Electronic Equipment Directive)
weight
length
CuttING CaPaCItIEs The maximum values indicated always stay for the performance limit under the most favourable cutting conditions, when the wire is placed as near as possible to the joint.
symBols
Article no. page
Length in
Length mm
ø in ø in ø in ø in
61 0 8 200 3/64 - 15/64 5/32 9/64 1/8 6262 12 4 3/4 120 1/64 - 3/64 1/32 6264 0 4 1/2 115 5/64 3/64 1/64 6464 11 4 1/2 115 1/16 1/32 6464 12 4 1/2 115 5/64 1/32 1/64 6464 22 4 1/2 115 1/32 6464 32 4 3/4 120 1/16 3/64 1/64 6464 42 4 1/2 115 1/16 3/64 1/64 6464 52 4 1/2 115 3/64 6464 62 4 3/4 120 1/64 64 / 6664 72 4 3/4 120 1/16 6467 0 5 1/2 140 5/32 1/8 5/64 1/16 67
6 1/4 160 3/16 1/8 7/64 5/64 678 200 13/64 5/32 1/8 7/64 67
68 01 6 1/4 160 5/32 7/64 3/32 677 1/4 180 5/32 1/8 3/32 67
8 200 5/32 9/64 7/64 6769 0 5 3/25 130 1/64 - 5/64 3/64 3/64 1/32 6770 4 1/4 110 1/8 5/64 3/64 69
5 125 1/8 3/32 1/16 695 1/2 140 5/32 3/32 5/64 696 1/4 160 5/32 7/64 5/64 697 1/4 180 5/32 1/8 3/32 69
71 .. 8 200 1/4 13/64 5/32 9/64 7073 0. 6 1/4 160 3/16 5/32 7/64 7573 71 7 1/4 180 7/32 3/16 1/8 1/8 7974 0. 5 1/2 140 1/8 5/64 1/16 76
6 1/4 160 1/8 3/32 5/64 767 1/4 180 5/32 7/64 3/32 76
8 200 11/64 1/8 3/32 7610 250 3/16 9/64 1/8 76
74 91 10 250 13/64 13/64 5/32 9/64 79
Article no. page
Length in
Length mm
ø in ø in ø in ø in
75 02 5 125 1/64 - 3/64 3/64 1/64 1/64 8075 12 5 125 1/64 - 3/64 3/64 1/64 1/64 8075 22 5 125 1/64 - 3/64 2/64 1/64 1/64 8075 52 5 125 1/64 - 3/64 1/64 1/64 8076 01 5 125 1/64 - 1/8 3/32 1/16 1/64 8177 01/02 4 1/2 115 1/64 - 1/16 3/64 1/64 82 /84
5 1/4 130 1/64 - 5/64 1/16 1/32 8277 12 4 1/2 115 1/64 - 1/16 3/64 1/64 8277 22 4 1/2 115 1/64 - 3/64 3/64 82 / 84
5 1/4 130 1/64 - 5/64 1/16 8277 42 4 1/2 115 1/64 - 3/64 1/32 82 / 84
5 1/4 130 1/64 - 1/16 3/64 82
77 72 4 1/2 115 1/64 - 1/32 8278 03 5 125 1/64 - 1/16 3/64 8678 23 5 125 1/64 - 3/64 1/64 8678 31/41 5 125 1/64 - 3/64 8678 61/71 5 125 1/64 - 1/16 3/64 1/64 8679 02 4 3/4 120 1/64 - 1/16 3/64 1/64 88 / 9079 02 5 125 1/64 - 5/64 3/64 1/32 88 / 9079 12 5 125 1/64 - 5/64 3/64 3/64 1/64 88 / 9079 22 4 3/4 120 1/64 - 3/64 1/32 88 / 9079 22 5 125 1/64 - 5/64 3/64 88 / 9079 32 5 125 1/64 - 1/16 3/64 1/64 88 / 9079 42 5 125 1/64 - 1/16 1/32 88 / 9099 0 8 200 5/64 1/16 60
8 3/4 220 3/32 1/16 6010 250 3/32 1/16 6011 280 7/64 5/64 6012 300 1/8 5/64 60
99 1 10 250 1/8 5/64 6112 300 5/32 5/64 61
centre cutter
cutting edges with bevel
cutting edges with small bevel
cutting edges with very small bevel
cutting edges without bevel
soft wire
medium hard wire
hard wire
piano wire
Cu + Al multi-conductor cable, solid and multi-stranded
wire rope
iron
dIrECtIoN aNd PosItIoN of CuttING EdGEs
CuttING EdGE shaPEs CoNformING to dIN Iso 5742
CuttING EdGEs tEChNICal BasICs
Material examples Type of wire Tensile strength
N/mm² kp/mm²
Copper, plastics soft 220 22
Nail, wire pin medium-hard 750 75
Wire rope strand, steel wire
hard 1800 180
Spring steel wire piano wire 2300 230
Safety instructionEach tool should only be used for its specified purpose. When using cutting pliers: beware of wire ends flying off. Wear protective goggles and, if needed, gloves. Be aware of those around you! Only handles marked with the symbol are insulated.
wIrE ClassEs
End Cutting Nipper
Oblique Cutter
Diagonal Cutter
Center Cutter
with bevel (outside bevel)
with small bevel (outside bevel)
with very small bevel (outside bevel)
without bevel (outside bevel)
Article numberHeAd/HAndles
0 Pliers black atramentized, head polished
1 Head polished,handles plastic coated
2 Head polished,handles with multi- component grips
3 Pliers chrome plated,handles plastic coated
4 Pliers chrome plated
5 Pliers chrome plated, handles with multi- component grips
6 Pliers chrome plated,handles insulated with multi-component grips;VDE-tested DIN EN/IEC 60900/ASTM F1505
7 Pliers chrome plated, handles with dipped insulation; VDE testedDIN EN/IEC 60900/ASTM F1505
8 Pliers head polished, handles with multi- component grips;VDE-tested DIN EN/IEC 60900/ASTM F1505
structure of Article number
Finish e.g.:head polished, handles black atramentized
Length e.g.:180 mm
Style e.g.:straight
Basic model e.g.: Combination Pliers
03 0 0 180
Registered Trademarks of the companies
Con-Pearl® PARAT-WERK Schönenbach GmbH + Co. KG
Duspol® Benning, Elektrotechnik and Elektronik GmbH & Co. KG
gesis® Wieland Electric GmbH
Kapton®, E. I. du Pont de KEVLAR® Nemours and Company
Radox® HUBER+SUHNER AG
Phillips® Phillips Screw Company
Pozidriv® European Industrial Service Ltd.
systainer® TANOS GmbH
MC® Multi-Contact AG
Solarlok® Tyco Electronics
Care TipsA drop of oil on polished surfaces and in the joint will keep the tool in good working order and will increase the service life of your pliers.
No. Article P.
86 Pliers Wrenches 98
87 0 KNIPEX Cobra® 100
87 0 KNIPEX Cobra® XL/XXL 102
85 KNIPEX Auto-Adjusting Pliers 100
87 21 KNIPEX Cobra® QuickSet 105
87 26 KNIPEX Cobra® VDE 105
87 4 KNIPEX Raptor™ Pliers 102
87 5 KNIPEX Cobra® ES 107
88 KNIPEX Alligator® 108
90 Mini Water Pump Pliers 110
No. Article P.
90 20 Pipe Cutter for plastic conduit pipes and hoses
111
90 25 Pipe Cutter for composite pipes and protective tubes
111
90 25 Pipe Cutter for composite and plastic pipes
112
90 4 Punch Lock Riveters 112
90 55 Sheet Metal Nibbler 113
90 61 Notching Pliers 113
90 7 Revolving Punch Pliers 114
91 1 Tile Breaking Pincer 114
91 3 Glass Breaking Pincer 114
91 Glass Nibbling Pincers 115
91 6 Flat Nose Grozing Pliers 115
WaTeR PumP PlieRs
sPeCial PlieRs sPeCial Tools
contents
No. Article P.
02 High Leverage Combination Pliers 20
03 Combination Pliers 21
09 ”Lineman‘s Pliers“ 22
No. Article P.
11 Insulation Strippers 23
11 8 Electronics Wire Stripping Shears
24
11 9 Electronics Wire Stripper 24
12 Insulation Strippers with shaped blades
24
12 12 Precision Insulation Strippers
26
12 40/50 Self-Adjusting Insulation Strippers
28
12 42 KNIPEX MultiStrip 10 29
12 62 Automatic Insulation Stripper
30
12 64 Automatic Insulation Stripper for flat cable
30
12 80 Mini Stripping Tool 31
13 Electricians‘ Pliers 31
13 8 Installation Pliers 32
15 11 Stripping Tweezers for Coated-Wire
33
16 20 Dismantling Tools 33
16 30 Dismantling Tool 33
16 40 Dismantling Tool 34
16 65 Dismantling Tool for data cables
34
No. Article P.
19 Round Pliers with cutting edge (Jewellers‘ Pliers)
35
20 Flat Nose Pliers 35
22 Round Nose Pliers 36
23Flat Nose Pliers with cutting edges (precision mechanics pliers)
36
25 Snipe Nose Side Cutting Pliers (Radio Pliers)
37
26 Snipe Nose Side Cutting Pliers (Stork Beak Pliers)
38
28 Assembly Pliers 39
29 Telephone Pliers 39
31 Gripping Pliers (Needle-Nose Pliers) 40
30 Long Nose Pliers 41
30 41 Halogen Bulb Exchange Pliers 40
32 Relay Adjusting Pliers 42
33 Duckbill Pliers 42
34 Precision Electronics Gripping Pliers / ESD
43/44
35 Electronics Pliers 45
35 Electronics Pliers ESD 46
36 Electronics Mounting Pliers 47
37 Gripping Pliers 48
38 Mechanics‘ Pliers 49
No. Article P.
40 Universal Grip Pliers 50
41 Grip Pliers 50
No. Article P.
44 Circlip Pliers for internal circlips 52
46 Circlip Pliers for external circlips 53
44 Circlip Pliersfor large internal circlips
54
45 Special Retaining Ring Pliersfor retaining rings on shafts
54
46 Circlip Pliers for large external circlips 55
46 Circlip Pliers for grip rings on shafts 55
46 Circlip Tool 58
48 Precision Circlip Pliersinternal circlips
56
49 Precision Circlip Pliers for external circlips
57
No. Article P.
50 Carpenters‘ Pincers 59
51 Hammerhead Style Carpenters‘ Pincers 59
55 Farriers‘ Pincers (Tear-off Pliers for vehicle bodywork)
59
57 Unsoling Pincer for horseshoes (for the farrier)
60
No. Article P.
99 0 Concretors‘ Nippers 60
99 1 High Leverage Concretors‘ Nippers 61
No. Article P.
61 Bolt End Cutting Nippers 63
62 Electronics Oblique Cutting Nipper 63
64 Electronics End Cutting Nippers / ESD
64/ 66
67 High Leverage End Cutting Nippers
67
68 End Cutting Nippers 67
69 End Cutting Nippers for mechanics
67
70 Diagonal Cutters 69
71 KNIPEX CoBolt® Compact Bolt Cutters
70
71 72 Bolt Cutters 72
71 82 Concrete Mesh Cutter 73
72 Diagonal Cutters for plastics 74
72 51 Diagonal Cutter for fibre optics 74
73 KNIPEX X-Cut 75
74 High Leverage Diagonal Cutters 76/77
74 7 KNIPEX TwinForce 79
74 91 High Leverage Center Cutters 79
75 Electronics Diagonal Cutters 80
76 Diagonal Cutters for electromechanics
81
77 Electronics Diagonal Cutters 82
77 Electronics Diagonal Cutters ESD 84
78 Electronic Super Knips® 86
78 Electronic Super Knips® ESD 88
79 Precision Electronics Diagonal Cutters
90
79 Precision Electronics Diagonal Cutters ESD
92
No. Article P.
81 Pipe Gripping Pliers 95
84 Cycle Pliers 95
83 Pipe Wrenches 96
CombinaTion PlieRs
WiRe sTRiPPeRs + DismanTling
Tools
gRiPPing PlieRs
gRiP PlieRs
CiRCliP PlieRs
CaRPenTeRs‘ PinCeRs
ConCReToRs‘ niPPeRs
CuTTing PlieRs
PiPe WRenChes
Tool KiTs
No. Article P.
92 Precision Tweezers 116
92 Precision Tweezers insulated 117
92 Precision Tweezers ESD 117
PReCision TWeezeRs
No. Article P.
95 Cable Shears 118
95 Cable Shears with twin cutting edge
119
95 Cable Shears 120
95 3 Cable Cutters (ratchet action)
120/ 121
95 32 Cable Shears with telescopic handles
122
95 32 Cable Cutters with telescopic handles
123
95 6 Wire Rope Shears 124
95 6 Bowden Cable Cutter 125
95 Wire Rope and Cable Cutters 125
Cable anD WiRe RoPe sheaRs
insulaTeD Tools
Din en/ieC 60900/ asTm F1505
sales aiDs
ConTRol CabineT
Keys
eleCTRoniCs-PlieRs
No. Article P.
97 2 Crimping Pliers 126
97 32 Crimping Pliers 126
97 43 Crimp System Pliers 127
97 49 Crimping Dies 128/ 129
97 Locators 129
97 Mounting Tool for MC3 connectors 130
97 51 Crimping Pliers for Western plugs
132/ 130
97 52 Crimping Pliers (two-hand operation)
131
97 52 Crimping Pliers short design 132
97 52 Crimping Pliers ”Preciforce“ 133
97 52 Four-Mandrel Crimping Pliers for turned contacts
134
97 53 Self-Adjusting Crimping Pliers for end sleeves
135/ 136
97 Crimping Pliers for end sleeves
137
97 91 Tool Case for Photovoltaics 138/ 139
97 99 Cable Connectors 140
No. Article P.
02/03 (High Leverage) Combination Pliers
144
09 Lineman‘s Pliers 145
11/13 Insulation Strippers 145
20 Flat Nose Pliers 146
22 Round Nose Pliers 146
25 Snipe Nose Side Cutting Pliers (radio pliers)
147
26 Snipe Nose Side Cutting Pliers (stork beak pliers)
147
30 Long Nose Pliers 146
70 Diagonal Cutters 148
73 KNIPEX X-Cut 149
74 High Leverage Diagonal Cutters
148
86 07 Pliers Wrench 149
88 KNIPEX Alligator® 150
87 26 KNIPEX Cobra® VDE 150
95 Cable Shears 151-152
95 3 Cable Cutters (ratchet action) 153
95 7 Wire Rope and ACSR-Cable Cutter
154
97 68 Crimping Pliers for end sleeves
154
98 0 Open End / Box Wrenches 155
98 0 Nut Drivers 156
98 07 Adjustable Wrench 157
98 Screwdrivers from 157
98 Hexagon Sockets 159/160
98 4 Reversible Ratchet 160
98 Torque Wrench 160
98 5 Cable Knives 161/162
98 5 Dismantling Knives 161
98 6 Flat Nose Pliers of Plastic 162
98 6 Snipe Nose Pliers of Plastic 162
98 6 Insulating Clamp 162
98 6 Plastic Slip-On Caps 163
98 6 Self Clamping Slip-On Caps
163
98 90 Puk® Junior Hacksaw 163
98 Tool Cases and Sets from 164
No. Article P.
00 19 Test Supports 187
00 19 Sales Display 187
00 19 Pliers Racks 188
00 19 Sales Displays 189
00 19 Magnetic Label 189
No. Article P.
00 19 Counter Displays 175
00 19/20
Circlip Pliers Sets 176/177
00 20 Pliers Sets in a foam tray
from 178
00 20 Pliers Sets from 179
00 21 Tool Cases from 181
No. Article P.
11 92 Electronic Wire Strippers 24
34 Precision Electronics Gripping Pliers
43
35 Electronic Pliers 45
35 Electronic Pliers ESD 46
36 Electonics Mounting Pliers 47
62 Electronics Oblique Cutting Nippers
63
64 Electronics End Cutting Nippers
64
64 Electronics End Cutting Nippers ESD
66
75 Electronics Diagonal Cutters 80
76 Diagonal Cutters for electromechanics
81
77 Electronics Diagonal Cutters 82
77 Electronics Diagonal Cutters ESD
84
78 Electronic Super Knips® / ESD
86/ 88
79 Precision Electronics Diagonal Cutters / ESD
90/ 93
92 Precision Tweezers from
116
00 20 Electronics Pliers Sets 183
Tool bags anD Tool
CasesNo. Article P.
00 19 Tool Bags 185
00 21 Tool Cases 186
CRimPing PlieRs anD
-assoRTmenTs
tHe rAnge of Products
No. Article P.
12 12 11Precision Insulation Strippers
26
97 43 200 Crimp System Pliers 127
97 91 Tool Cases for Photovoltaics
139
Tools FoR PhoTo-
volTaiCs
No. Article P.
00 11 KNIPEX TwinKey® 172
00 11 Control Cabinet Keys 173
00 11 Profi-Key 173
00 11 Universal Key 173
00 11 Pen-Style Control Cabinet Key 174
00 11 Pen-Style Profi-Key 174
44
5
How everytHing begAn – And A simPle PrinciPle
1882 Carl Gustav Putsch set up his own small forge shop in Cronenberg (now a part of Wuppertal).
1922 Carl Putsch takes over mana-gement. The company develops into an industrial firm.
1942 KNIPEX, the brand, is created and registered.
1954 Karl Putsch (photo left), the grandson of the company founder, takes over management of the family-owned company. Numerous innova-tions and modern production techno-logy characterise the development.
1987 Ralf Putsch joins the com pany. International sales are seriously ex-panded. Other tool manufacturers become part of the KNIPEX Group.
Carl Gustav Putsch wanted to stand on his own two feet after completing his apprentice-ship as blacksmith with his father. He therefore set up his own business in 1882 and forged carpenters‘ and farriers‘ pincers with two journeymen, 60 pieces per day. The other processes were also carried out in careful manual labour. The quality was sought after, the small enterprise grew.
The next generations were able to build continuously on these foundations. We have retained an independent family-owned company up to the present day. A lot has changed since the first years. Over time, the workshop turned into a factory with modern machinery and continuously improving technology. New types of pliers and pioneering innovations were added. The number of supplied countries grew steadily.
However, our fundamental principle has stayed in place: remain faithful to a product group, concentrate all strengths on it and be „simply the best“ in pliers. Don‘t get side-tracked, instead create more performance and quality in a single segment. This is what KNIPEX stands for as today‘s leading brand in pliers.
6
for wHom we mAke Pliers
They are constantly in our mind: People who work with tools professionally. Who need to be able to rely on their tools, even when the going gets tough. Who expect their tools to last a long time. In other words: Users who are demanding in every respect and who want only the best.
We offer these users a range of around 1,000 different pliers. With this choice we can provide exactly the right tool for every application - and always in a suitable design and size.
Because the verdict of the professionals is our benchmark, we are always looking for their feed-back. About how they work with their pliers and what‘s important to them, so that we can understand precisely and in detail what matters to them.
Paramount is to know what makes their work easier, quicker and safer. That is, the subject of ergo nomics, adapting working appliances to their users. Despite high performance, tools should never stress a user more than necessary. Here, for example, the good design of pliers handles is not the only criterion. We always find new ways of saving strength and relieving the whole hand-arm system.
7
for wHom we mAke Pliers
8
9
QuAlity in every detAil
Sometimes we give our pliers a really hard time. We try to destroy them to find out what makes them good and long-lasting. Because we don‘t want to leave anything to chance, we take a long, careful look.
Correctly hardened, this steel guarantees optimum cutting performance and service life. That‘s why we use it for our pliers – even if it has to be produced especially for us, costs more and is hard to process. But our high product demands require this.
The rivet of the high-leverage diagonal cutter also has to stand up to a lot of stress. That‘s why we literally give it backup: we forge it straight onto the pliers. This means extra effort – we have to precision mill the rivet to a few hundredth millimeters. Satisfied users are worth this effort.
And then there are, no less important: the angles, the sharpness, the hardness, the toughness of the cutting edges. The precision and smooth movement of the joint. The handle design and the finish: we keep reviewing these subjects, we research, test and improve.
Many trials, for example, have shown us that high-leverage diagonal cutters for very hard wire should be alloyed at best with 0.8% carbon and certain defined parts of chromium and vanadium.
10
mAde in wuPPertAl, germAny
A lot has to come together so that we can make the best pliers.First of all, the special material. Then: modern processing methods and machines. We want to work with high precision and efficiently at all times.
The machines we require for our special needs are not always available on the market. Then we construct these ourselves. Our mechanical engineers come up with state-of-the-art solutions even for tricky tasks.
And last but not least: our employees. With their comprehensive experience, their knowledge and skills they make sure that everything turns out precisely as our customers expect. So that we can keep the KNIPEX promise.
Our pliers run through many production steps which are all carefully coordinated. From forging to machining, hardening, surface finishing and all the way to packing, these steps are all carried out under the one roof. This means that we can have a direct and complete influence on how our products are created.
The short distances allow us to respond quickly and implement improvements immediately.
11
12
13
tHe tHink tAnk
When we have achieved something we are happy – but we don‘t stop there. For us, better is the enemy of the good. And we like to be the first to have the good ideas for better pliers.
We continuously work on new products and product advantages which offer our users tangi-ble added value. For example by saving handforce when cutting or adjusting pliers for gripping quicker and with more precision. Or you can work without a heavy tool because a more compact one can do the same job.
No matter whether it‘s a small improvement or a totally new idea: everything is meticulous-ly thought out and designed with state-of-the-art software. New models are then put through the acid test – with the help of computer simulations in the test lab and in user testing. The results are then used to further optimise the product, it is re-tested and finally released for production.
By the time they‘re on the market our pliers have already come a long, hard way.
14
our customers
Reliably, confidently and long-term – this is how we wish to collaborate with our customers. We have been doing precisely this for decades with many of them. We offer high quality, performance, good service and contact partners who know what it‘s all about. We want working with us to be easy and pleasant.
Our brand is known and appreciated by consumers. We offer various support for the sale of our products. We visit users together with our distributors to present our tools. We train our partners‘ field salesforce because a lot can be said about our pliers which the salesperson can use as con-vincing arguments.
Our understanding of partnership also means that we do not sell directly to end users. And there are no exceptions.
Today, customers in more than 100 countries bank on our products. We reach them via a con stantly enlarging, worldwide network of agencies, our own subsidiaries and importers. By ob serving the many markets we can gain insights and discover important trends, which will be beneficial to the up-to-dateness and competence of our range. Our customers also benefit from this.
15
Kleště
Szczypce
ALICATES P inze
7 ˆ 1 * ( 5
PincesTenger
) 2 * •
Kerpeten
ZANGE
ペンチ ALICATe
KlIješTA钳子
PliersКлещи
Tang
πένσα
16
17
our vAlues – our emPloyees
We want to be successful and do a lot to achieve this. But we don‘t want economic success at any price and not at the expense of values which are important to us.
Our aspirations are to act and operate sustainably. The longevity of our products is only one aspect of many.
We feel closely linked with our location. That is why we are particularly aware that we have a responsibility towards our environment and society – and thereby our future generations. We want to treat resources carefully and not burden nature more than absolutely necessary.
We engage ourselves in many ways in our sphere, in particular in the sectors of education, social policy and culture.
Our employees are particularly important to us. They provide the basis for our success with their knowledge and skills, their commitment and ideas. We train them very thoroughly and sup-port them when they want to develop themselves and learn something new. We put emphasis on a good an fair cooperation and know that we can only attain our high targets jointly.
18
97 91 01
sPeciAl tools for PHotovoltAics All work stePs well co-ordinAted for best results
There is a steadily increase of electrical power produced by photovoltaic plants (PV systems). The output from this en viron-mentally friendly source of energy rises each year by about 20% world wide. However, the share in the total power generati-on is still below 0.3% worldwide, which means there is still rich potential for growth. This makes photo voltaic a profitable sphere of activities for trade and for electrical contractors.
The photovoltaic tools from KNIPEX, customized for cutting, stripping and crimping the special photovoltaic cables and con-nectors, offer professional and reliable work results and ensure that the relevant requirements, such as e.g. Ral GZ 966, are met.
The requirements for a technically perfect installation of the photo voltaic systems are very high. It is a demanding task to crea-te an electrically efficient and constantly reliable connection in combi nation with high mechanical requirements.
19
Huber + Suhner Multi-Contact HirschmannTycoWieland and others
Article No. 97 91 01: all tools required for assembly in one case equipped with crimping dies for standard solar cable connectors
Tool Case for Photovoltaics
for contacts from:
sPeciAl PHotovoltAic rAnge from kniPeX
Cut effected with a Cable Shears: easy, clean cut without any deformation of the cable.
Huber + Suhner
Multi-Contact MC3
Multi-Contact MC4
Hirschmann
Tyco
Wieland
Locatorsfor an exact connector positioning in the crimp profile
High demands in terms of results require the use of high-quality special tools also. These must be adapted precisely to suit systems from various manufacturers.
As the systems are not compatible with each other, each type of connector requi-res a set of individual crimping dies. The range is completed by locators to support quick, easy and precise work.
20
02
02 01 180
02 02 180
02 08 225
Cutting capacitiesProduct Number inch mm
Pliers Head Handles
Ø inch Ø inch Ø inch AWG Ø mm Ø mm Ø mm mm² Ounces
02 01 180 7 1/4 180 black
atramentizedpolished plastic coated
3/32 5/64 29/64 5 2.5 2.0 11.5 16.0 7.1
02 01 200 8 200 7/64 3/32 1/2 3 2.8 2.2 13.0 25.0 10.5
02 01 225 9 225 1/8 3/32 35/64 3 3.0 2.5 14.0 25.0 12.6
02 02 180 7 1/4 180
black atramentized
polished with multi-component grips
3/32 5/64 29/64 5 2.5 2.0 11.5 16.0 8.5
02 02 200 8 200 7/64 3/32 1/2 3 2.8 2.2 13.0 25.0 12.1
02 02 225 9 225 1/8 3/32 35/64 3 3.0 2.5 14.0 25.0 14.4
02 08 200 sba 8 200black atramentized
polished insulated with multi-component grips, VDE-tested
7/64 3/32 1/2 3 2.8 2.2 13.0 25.0 12.1
02 08 225 sba 9 225 1/8 3/32 35/64 3 3.0 2.5 14.0 25.0 14.4
■ 35% less effort required compared to conventional combination pliers ■ easier work due to high leverage design■ with cutting edges (hardness approx. 63 HRC) for soft, hard,
piano and ACSR wire■ long cutting edges for thicker cables ■ with gripping zones for flat and round material,
suitable for versatile use ■ High-grade special tool steel; forged, oil-hardened
high leverage Combination Pliers ISO 5746
combinAtion Pliers
easier cutting. Powerful gripping, bending and pulling.
21
03Combination Pliers ISO 5746
03 01 180
03 02 180
■ with gripping zones for flat and round material, suitable for versatile use
■ with cutting edges for soft and hard wire ■ long cutting edges for thicker cables ■ cutting edge hardness approx. 60 HRC■ Special tool steel; forged, oil-hardened
Cutting capacitiesProduct Number inch mm
Pliers Head Handles
Ø inch Ø inch Ø inch AWG Ø mm Ø mm Ø mm mm² Ounces
03 01 140 5 1/2 140
black atramentized
polished plastic coated
7/64 5/64 23/64 7 2.8 1.8 9.0 10.0 4.0
03 01 180 7 1/4 180 9/64 3/32 15/32 5 3.4 2.2 12.0 16.0 7.6
03 01 200 8 200 5/32 3/32 33/64 5 3.8 2.5 13.0 16.0 9.7
03 01 250 10 250 5/32 3/32 19/32 3 3.8 2.5 15.0 25.0 17.2
03 02 160 6 1/4 160
black atramentized
polishedwith multi-component grips
1/8 5/64 25/64 5 3.1 2.0 10.0 16.0 7.9
03 02 180 7 1/4 180 9/64 3/32 15/32 5 3.4 2.2 12.0 16.0 9.0
03 02 200 8 200 5/32 3/32 33/64 5 3.8 2.5 13.0 16.0 11.4
03 08 160 sba 6 1/4 160black atramentized
polishedinsulated with multi-component grips, VDE-tested
1/8 5/64 25/64 5 3.1 2.0 10.0 16.0 7.9
03 08 180 sba 7 1/4 180 9/64 3/32 15/32 5 3.4 2.2 12.0 16.0 9.0
03 08 200 sba 8 200 5/32 3/32 33/64 5 3.8 2.5 13.0 16.0 11.4
combinAtion Pliers
03 08 200
22
09lineman‘s Pliers new england style
ISO 5746 ASME B107.20
09 01 240
09 02 240
09 11 240
■ heavy duty■ high transmission ratio for easy cutting ■ high leverage design requires 40% less effort compared to
conventional combination pliers ■ effective cross-hatched knurled gripping zone in the jaws –
for strong gripping and pulling ■ additional serrated gripping zone below the articulated joint
for powerful leverage■ with cutting edges for soft, hard and ACSR wire■ cutting edge hardness approx. 64 HRC ■ Vanadium electric steel; forged, oil-hardened
09 11 240 / 09 12 240includes a crimper and a fish tape puller in the joint gap
Gripping zone below the joint for powerful leverage
Cross hatched serrated gripping zone for firm gripping and pulling, e. g. for fencing
Long cutting edges for cutting flat cables 09 11/12 240: Fish tape puller in the joint gap
09 11/12 240: Crimping area below the joint
Cutting capacitiesProduct Number inch mm
Pliers Head Handles
Ø inch Ø inch Ø mm Ø mm Ounces
09 01 240 9 1/2 240 black atramentized polished with non-slip plastic coating 3/16 1/8 4.6 3.0 15.3
09 02 240 9 1/2 240 black atramentized polished with multi-component grips 3/16 1/8 4.6 3.0 16.6
09 08 240 9 1/2 240 black atramentized polishedinsulated with multi-component grips, VDE-tested
3/16 1/8 4.6 3.0 16.6
09 11 240 9 1/2 240 black atramentized polished with non-slip plastic coating 3/16 1/8 4.6 3.0 15.3
09 12 240 9 1/2 240 black atramentized polished with multi-component grips 3/16 1/8 4.6 3.0 16.6
combinAtion Pliers
09 08 240
23
wire striPPers And dismAntling tools
11insulation strippers
11 01 160
11 02 160
■ for single, multiple and fine-stranded conductors with plastic or rubber insulation of a maximum 13/64“ diameter. Also suitable for 7 AWG wire.
■ easy adjustment to the required diameter of solid or stranded wire with knurled screw and lock nut
■ Special tool steel; forged, oil-hardened
Stripping capacitiesProduct Number inch mm
Pliers Head Handles Ø inch Ø mm mm² AWG
Ounces
11 01 160 6 1/4 160 black atramentized polished plastic coated 13/64 5.0 10.0 7 4.6
11 02 160 6 1/4 160 black atramentized polished with multi-component grips 13/64 5.0 10.0 7 5.8
11 08 160 6 1/4 160 black atramentized polishedinsulated with multi-component grips, VDE-tested
13/64 5.0 10.0 7 5.9
Prismatic blade:The red area is cut over four surfaces. Works with highly-elastic materials also.
11 08 160
24
118 electronics Wire stripping shears
11 82 130
■ for cutting and stripping single, multiple and fine-stranded conductors with diameters up to 3/64“ (18 - 32 AWG)
■ easy adjustment to the required diameter of solid or stranded wire with knurled screw and lock nut
■ with opening spring ■ Special tool steel; oil-hardened
Stripping capacitiesProduct Number inch mm
Head Handles Ø inch Ø mm AWG
Ounces
11 82 130 5 130 polished with multi-component grips up to 3/64 0.03-1.0 18 - 32 2.6
wire striPPers And dismAntling tools
119 electronics Wire stripper
11 92 140
12 21 180
■ for single, multiple and fine-stranded cables up to 1/32“ dia. with plastic or rubber insulation
■ easy adjustment to the required diameter of solid or stranded wire with knurled screw and lock nut
■ with opening spring ■ the mirror polish, together with a fine film of oil, offer the best possible
rust protection – no circuit faults caused by peeling chrome from plated tools
■ Special tool steel; forged, oil-hardened
Stripping capacitiesProduct Number inch mm
Head Handles Ø inch Ø mm AWG
Ounces
11 92 140 5 140 mirror polished with multi-component grips up to 1/32 0.1 - 0.8 18 - 28 3.5
12insulation stripper with adapted blades
■ with replaceable blades for 4 or 6 different conductor cross-sections ■ leaves wire undamaged thanks to precision-ground blade shapes,
even multi-stranded conductors are stripped gently ■ during stripping, the wire is held firmly by clamping jaws ■ with length stop for constant stripping length during repetitive work ■ pliers body: aluminium ■ blade: Special tool steel; oil-hardened
Stripping capacitiesProduct Number inch mm
Pliers Handles mm² AWG
Ounces
12 21 180 7 1/4 180 black lacquered with plastic grips 0.5-0.75 / 1.0 / 1.5 / 2.5 / 4.0 / 6.0 0-19 / 10 / 11 / 13 / 15 / 17 12.9
12 29 180 1 pair of spare blades for 12 21 180
12 21 180: wire cross-sections in mm²
25
26
wire striPPers And dismAntling tools
1212 Precision insulation strippers
with adapted blades
12 12 02
12 12 06
12 12 11
Precise and Reliable
Two pairs of blades (1) cut the insulation completely. Then the blade pairs move apart, and thus the insulation is removed form-fit (2).The pliers opens automatically after the stripping procedure.
■ form-fit stripping of both standard and difficult-to-remove insulating materials such as PTFE, silicone, Radox®, Kapton® and rubber including multi-layer insulations
■ blades are shaped precisely to the respective conductor cross-section ■ an adjustable length stop is perfect for use when cutting the same
stripping lengths during repetitive work■ pliers body: steel ■ blades: Special tool steel; oil-hardened
12 12 02with additional cable guide for exact positioning of the conductor in the stripping area of the blades
12 12 11 for solar cables specially adapted to multi-layered and RADOX® insulation; with additional cable support for multi-layer insulated conductors in the stripping profiles
Stripping capacitiesProduct Number inch mm
Pliers Handles mm² AWG
Ounces
12 12 02 7 1/2 195
burnished with multi-component grips
0.03 - 2.08 14 - 32 15.8
12 12 06 7 1/2 195 0.14 - 6.00 10 - 26 15.7
12 12 10 7 1/2 195 2.5 - 10.0 7 -13 15.7
12 12 11 7 1/2 195 1.5 - 6.0 10 - 15 15.8
12 12 12 7 1/2 195 4.0 - 10.0 7 - 11 15.8
12 19 02 1 set of spare blades for 12 12 02
12 19 06 1 set of spare blades for 12 12 06
12 19 10 1 set of spare blades for 12 12 10
12 19 11 1 set of spare blades for 12 12 11
12 19 12 1 set of spare blades for 12 12 12
maximum cable cross-section (in mm²) per profile:
12 12 1012 12 06
12 12 02
12 12 1212 12 11
Kapton® is a registered trademark of E. I. du Pont de Nemours and Company
Solar
27
wire striPPers And dismAntling tools
12 12 02 with cable guide and length stop Precise cutting of the insulation The precise shape of the blades leads to perfect stripping
Automatic stripping of the insulation
Principle of operation with shaped blades
Neat and precise stripping with a circular cut around the conductor. Perfect for working with conductors which must be stripped precisely.
For use when working with PTFE, RADOX® and multi-layer insulation.
0.03 mm2
32 AWG
10 mm2
7 AWG
28
1240/50 self-adjusting insulation strippers
12 40 200
■ for single, multiple and fine-stranded conductors with standard plastic or rubber insulation
■ adjusts automatically to the respective cable cross-section which prevents damage to the conductor
■ cutting depth can be adjusted for different insulation materials ■ with wire cutter for copper and aluminium wires, multi-stranded
up to 7 AWG and single-stranded up to 10 AWG ■ smoothly operating mechanism ■ replaceable blade and plastic clamping jaws ■ light weight■ body: fiberglass-reinforced ■ blade: Special tool steel; oil-hardened
12 40 200for thin ribbon cables up to 7 AWG width in a single pass
Adjustable length stop Precise stripping prevents damage to the conductor
Wire cutter for multi-stranded wire cables up to 10.0 mm² / 7 AWG
Stripping capacities Length stopProduct Number inch mm
mm² AWG inch mm
Ounces
12 40 200 8 200 0.03 - 10.0 7 - 32 1/8 - 23/32 3.0 - 18.0 7.1
12 50 200 8 200 2.5 - 16.0 5 -13 7.0
12 49 01 1 pair of spare blades for 12 40 200
12 49 02 1 pair of spare clamping jaws for 12 40 200
12 49 03 Spare length stop for 12 40 200
12 59 01 1 pair of spare blades for 12 50 200
12 59 02 1 pair of spare clamping jaws for 12 50 200
sTRa
igh
T bl
aD
e
wire striPPers And dismAntling tools
29
wire striPPers And dismAntling tools
mode of operation of straight cuttersModels 12 40 200 and 12 42 195
An incision is made in the red area only.
Not suitable for highly-flexible or armored insulation materials or for multi-layered insulation.
1242
12 42 195
Patented mechanicsThe cutting capability of the stripping blade adapts to the diameter and thickness of all standard insulating materials. There is no need for manual adjustment like other tools.
Wire cutter for multiple stranded wire cables up to 10.0 mm² / 7 AWG
Steel restrain jaws with cutting edges avoid skidding of the cable
Precise stripping from 7 - 32 AWG without readjustment
Stripping capacitiesProduct Number inch mm
mm² AWG
Ounces
12 42 195 7 1/2 195 0.03 - 10.0 7 - 32 4.8 12 49 21 Spare blades block for 12 42 195
12 49 23 Spare length stop for 12 42 195
■ automatic adjustment to single, multi- and fine-stranded conductors with standard insulation. Range of 7 to 32 AWG.
■ no manual adjustment required; no damage to the conductors ■ steel clamping jaws with integrated cutting edges hold the cable
and prevent slipping■ with wire cutter for copper and aluminium conductors, multi-stranded
up to 7 AWG and single-stranded up to 10 AWG ■ light weight■ replaceable blades and length stop ■ handle with soft-plastic zone for a steady grip ■ body: plastic, fiberglass-reinforced ■ blade: Special tool steel; oil-hardened
KniPeX multistrip 10 automatic insulation stripper
stripping without readjustment from 7 to 32 aWg
30
wire striPPers And dismAntling tools
1262 automatic insulation stripper
12 62 180
■ compact standard tool at a favorable price for all current cable cross-sections and insulating materials
■ for single, multiple and fine-stranded cables of 10 AWG to 24 AWG with standard insulation
■ adapts automatically to the respective cable cross-section preventing damage to the conductor
■ ergonomic and lightweight■ narrow head style for use in confined areas ■ with wire cutter for copper and aluminium wires up to 14 AWG■ with adjustable length stop from 15/64“ - 23/32“ for stripping the
same lengths during repetitive work ■ body: plastic, fiberglass-reinforced ■ blades: Special tool steel; oil-hardened, interchangeable
Precise stripping from 0.2 up to 6.0 mm² / AWG 10 to AWG 24
Wire cutter up to 2.5 mm² / 14 AWG Stripping in confined areas
Stripping capacitiesProduct Number inch mm
mm² AWG
Ounces
12 62 180 7 1/4 180 0.2 - 6.0 10 - 24 5.3
12 69 21 1 pair of spare blades for 12 62 180
12 69 23 Spare length stop for 12 62 180
1264 automatic insulation stripper
for flat cable
12 64 180
■ for PVC-insulated flat cables up to a max. 15/32“ width and 14 AWG to 19 AWG
■ adapts automatically to the various conductor heights which prevents damage to the conductor
■ allows long stripping lengths ■ replaceable blade■ smoothly operating mechanism ■ lightweight■ body: fiberglass-reinforced ■ blade: Special tool steel; oil-hardened
Stripping capacitiesProduct Number inch mm
mm² AWG
Ounces
12 64 180 7 1/4 180 0.75 - 2.5 14 - 19 4.4
12 69 31 1 pair of spare blades for 12 64 180
0.2
mm
2
24 A
WG
6.0
mm
2
10 A
WG
31
12 80 040 sb
wire striPPers And dismAntling tools
1280 mini stripping Tool ■ precise stripping because of the tool's gradual adjustment to the
conductor's diameter ■ with wire cutter ■ adjustable length stop from 5/32“ - 19/32“ ■ with locking device ■ housing: plastic, impact-resistant
for thin copper conductors dia. 0.12 to 0.4 mm (26 - 36 AWG)
Stripping capacitiesProduct Number inch mm
Ø mm AWG
Ounces
12 80 040 sb 4 100 0.12 - 0.4 26 - 36 1.2
13electrician‘s Pliers
13 01 160
13 02 160
13 01 614
■ the ideal pliers for cable work ■ for gripping and bending wire ■ for cutting soft, medium and hard wire ■ precision cutting edges additionally hardened,
cutting edge hardness approx. 60 HRC ■ with precision stripping holes ■ for crimping end sleeves (ferrules) ■ Vanadium electric steel; forged, oil-hardened
Gripping Cutting
Stripping Crimping 0.5 to 2.5 mm² / AWG 14 - AWG 20
Cutting capacitiesProduct Number inch mm
Pliers Head Handles Stripping capacities
Ø inch Ø inch Ø mm Ø mm Ounces
13 01 160 6 1/4 160 black atramentized polished plastic coated 0.5 - 0.75 / 1.5 / 2.5 mm² 3/32 1/16 2.5 1.6 4.0
13 02 160 6 1/4 160 black atramentized polished with multi-com-ponent grips
0.5 - 0.75 / 1.5 / 2.5 mm² 3/32 1/16 2.5 1.6 5.0
13 01 614 6 1/4 160 black atramentized polished plastic coated 10 / 12 / 14 AWG 3/32 1/16 2.5 1.6 4 .0
32
WiRe sTRiPPeRs anD DismanTling Tools
138 installation Pliers ■ multifunctional pliers for the electrical installation; for cutting cable,
stripping and crimping end sleeves (ferrules), to grip flat and round material, for bending, deburring
■ 6 functions in one pair of pliers ■ smooth surfaces near the tips grip single conductors without damaging
them; serrated gripping surfaces and pipe grip for gripping flat and round material
■ clear-cut outside edge on the jaw for working on flush-mounted junction boxes and deburring feed-through holes
■ stripping holes for 12 + 14 AWG■ crimp die for end sleeves (ferrules) 12 - 20 AWG ■ cable shears with (induction-hardened) precision cutting edges for
copper and aluminium cables up to 19/32“ dia. ■ slim dimensions for easy access ■ bolted joint: precise, zero backlash operation of pliers ■ High-grade special tool steel; forged, oil-hardened
13 81 8
13 82 8
13 88 8
Product Number inch
Pliers Head Handles Stripping capacity for cross-sections
AWG
Crimpingcapacity
AWG Ounces
13 81 8 8 black atramentized polished plastic coated 12 + 14 12 - 20 9.3
13 82 8 8 black atramentized polished with multi-component grips 12 + 14 12 - 20 9.9
13 88 8 8
black atramentized polished
insulated with multi-component grips, VDE-tested
12 + 14 12 - 20 9.9
Product Number mm
Pliers Head Handles Stripping capacity for cross-sections
AWG
Crimpingcapacity
mm2 Ounces
13 81 8 200 black atramentized polished plastic coated 12 + 14 0.5 - 2.5 9.3
13 82 8 200 black atramentized polished with multi-component grips 12 + 14 0.5 - 2.5 9.9
13 88 8 200
black atramentized polished
insulated with multi-component grips, VDE-tested
12 + 14 0.5 - 2.5 9.9
33
WiRe sTRiPPeRs anD DismanTling Tools
1511 Coated-Wire stripping Tweezers
15 11 120
■ for stripping off varnished insulation on copper wires
■ blades for other wire diameters available as spare parts
■ tweezers body: spring steel; oil-hardened ■ handle shells: plastic
Product Number
15 19 006 1 pair of spare blades for 15 11 120 Ø 1/64 in (0.6 mm)
15 19 008 1 pair of spare blades for 15 11 120 Ø 1/32 in (0.8 mm)
Stripping capacitiesProduct Number inch mm
Ø inch Ø mm
Ounces
15 11 120 4 1/2 120 1/64 0.6 1.2
1630 Dismantling Tool ■ for dismantling round cable sheaths made of PVC, rubber, silicon
or PTFE from 15/64“ - 1 9/64“ dia. and 40 - 1000 MCM■ self-cocking holding lever ■ with knurled nut for cutting depth adjustment ■ changing from circular to longitudinal cutting by turning the tool body ■ spiral cutting for removing intermediate pieces ■ replaceable blade ■ housing: plastic, impact-resistant
Stripping capacitiesProduct Number inch mm
Ø inch Ø mm MCM
Ounces
16 30 135 sb 5 1/4 135 15/64 - 1 9/64 6.0 - 29.0 40 - 1000 4.2
16 30 135 sb
1620 Dismantling Tool
16 20 16 sb
■ for stripping all common round cables
■ self-cocking holding lever ■ with adjusting screw for cutting
depth adaptation ■ turnable blade for circular and
longitudinal cutting ■ spare blade inside the handle ■ secure grip due to soft
component material on handle and holding lever to avoid slipping
■ housing: plastic, impact-resistant16 20 165 sbwith knife and hook blade inclusive protective cap
Stripping capacitiesProduct Number inch mm
Ø inch Ø mm
Ounces
16 20 16 sb 5 1/4 130 5/32 - 5/8 4.0 - 16.0 1.2
34
wire striPPers And dismAntling tools
1640 Dismantling Tool
16 40 150 sb
■ for dismantling round cables exceeding 1“ in dia. ■ removes all kinds of insulation layers ■ suitable for longitudinal and circular cutting ■ cutting depth can be adjusted up to 13/64“ ■ replaceable blade (both sides can be used) ■ tool body: plastic, fiberglass-reinforced
Setting the tool for longitudinal cut Longitudinal cut
Turning the tool for circumferential cut Circular cut
Adjustable cutting depth
Stripping capacitiesProduct Number inch mm Ø inch Ø mm Ounces
16 40 150 sb 6 150 1 > 25 7.4
16 49 150 Spare blade for 16 40 150 SB
1665 Dismantling Tool for data cables
16 65 125 sb
■ for stripping UTP and STP data cables with diameters of 11/64“ to 25/64“
■ stripping device for 11 - 24 AWG ■ double shell, folding back stripping tool ■ with opening spring and locking lever ■ clip for safe transport ■ body: plastic, fiberglass-reinforced
Stripping capacitiesProduct Number inch mm
Types of cables Ø inch Ø mm AWG mm²
Ounces
16 65 125 sb 5 125 CAT 5, CAT 6, CAT 7, Twisted-Pair (UTP/STP) 11/64 - 25/64 4.5 - 10.0 11 - 24 0.2 - 4.0 1.8
35
griPPing Pliers
20Flat nose Pliers ISO 5745
20 01 160
■ flat, short and wide jaws ■ serrated gripping surfaces ■ Chrome vanadium electric steel;
forged, oil-hardened
DimensionsProduct Number inch mm
Pliers Head Handles L3inch
W3inch
T1inch
L3mm
W3mm
T1mm Ounces
20 01 125 5 125
black atramentized
polished plastic coated
1 1/16 37/64 5/16 27.0 14.5 8.0 2.6
20 01 140 5 1/2 140 1 3/32 39/64 3/8 28.0 15.5 9.5 3.8
20 01 160 6 1/4 160 1 3/16 43/64 3/8 30.0 17.0 9.5 5.1
20 01 200 8 200 1 1/2 53/64 15/32 38.0 21.0 12.0 9.5
20 06 160 6 1/4 160
chrome plated
insulated with multi-component grips, VDE-tested
1 3/16 43/64 3/8 30.0 17.0 9.5 5.1
19 Round nose Pliers with cutting edge (Jewelers‘ Pliers)
ISO 5743
19 01 130
■ for fine wire and working with jewelery
■ ideal for cutting and bending work, also in electronics
■ for bending wire loops ■ precision-ground smooth, round
jaws with fine, pointed tips ■ cutting edges additionally
hardened, cutting edge hardness approx. 60 HRC
■ Vanadium electric steel; forged, oil-hardened
Dimensions Cutting capacitiesProduct Number inch
Pliers Head Handles D1inch
L3inch
T1inch
W3inch
W4inch Ø inch Ø inch Ounces
19 01 130 5 1/8 black atramentized polished plastic coated 3/64 1 17/64 5/16 17/32 5/64 3/32 1/16 2.6
Dimensions Cutting capacitiesProduct Number mm
Pliers Head Handles D1mm
L3mm
T1mm
W3mm
W4mm Ø mm Ø mm Ounces
19 01 130 130 black atramentized polished plastic coated 1.0 32.0 8.0 13.5 2.0 2.2 1.6 2.6
20 06 160 sba
36
griPPing Pliers
22Round nose Pliers ISO 5745
22 01 160
22 02 160
■ for bending wire loops ■ round, short jaws; smooth ground ■ Chrome vanadium electric steel; forged, oil-hardened
DimensionsProduct Number inch mm
Pliers Head Handles L3inch
W3inch
D1inch
T1inch
L3mm
W3mm
D1mm
T1mm Ounces
22 01 125 5 125
black atramentized
polished plastic coated
1 1/16 37/64 5/64 5/16 27.0 14.5 2.0 8.0 2.6
22 01 140 5 1/2 140 1 3/32 21/32 7/64 3/8 28.0 16.5 2.5 9.5 3.5
22 01 160 6 1/4 160 1 3/16 23/32 1/8 3/8 30.0 18.0 3.0 9.5 4.9
22 01 180 6 1/4 180 1 3/8 53/64 9/64 13/32 35.0 21.0 3.5 10.5 6.2
22 02 140 5 1/2 140
black atramentized
polished with multi-component grips
1 3/32 21/32 7/64 3/8 28.0 16.5 2.5 9.5 4.6
22 02 160 7 1/4 160 1 3/16 23/32 1/8 3/8 30.0 18.0 3.0 9.5 6.0
22 08 160 sba 7 1/4 160
black atramentized
polishedinsulated with multi-com-ponent grips, VDE-tested
1 3/16 23/32 1/8 3/8 30.0 18.0 3.0 9.5 6.0
23Flat nose Pliers with cutting edges (precision mechanics pliers)
ISO 5745
23 01 140
■ suitable for gripping and cutting work in fine mechanics
■ flat, long and tapered jaws■ cutting edges additionally
induction hardened, cutting edge hardness approx. 60 HRC
■ High-grade special tool steel; forged, oil-hardened
Cutting capacities DimensionsProduct Number inch
Head Handles
Ø inch Ø inch
T1 inch
L3inch
W3inch
W4inch
T2inch Ounces
23 01 140 5 1/2 polished plastic coated 7/64 1/16 9/32 1 3/8 1/2 1/8 3/16 2.6
Cutting capacities DimensionsProduct Number mm
Head Handles
Ø mm Ø mm
T1mm
L3mm
W3mm
W4mm
T2mm Ounces
23 01 140 140 polished plastic coated 2.5 1.6 7.0 35.0 12.5 3.0 4.5 2.6
22 08 160 sba
37
griPPing Pliers
25 snipe nose side Cutting Pliers (radio pliers)
ISO 5745
25 01 160
25 02 160
■ suitable for fine gripping and cutting work ■ pointed, half-round jaws ■ serrated gripping surfaces ■ with cutting edges for soft, medium and hard wire ■ cutting edges additionally induction hardened,
cutting edge hardness approx. 61 HRC ■ Vanadium electric steel; forged, oil-hardened
Cutting capacities DimensionsProduct Number inch
Pliers Head Handles
Ø inch Ø inch
L3inch
L4inch
W3inch
T1inch
W4inch
T2inch Ounces
25 01 125 5 black
atramentizedpolished plastic coated
3/32 1/16 1 1/16 1/2 9/32 3/32 5/64 2.6
25 01 140 5 1/2 3/32 1/16 1 21/32 19/32 5/16 3/32 5/64 3.1
25 01 160 6 1/4 3/32 1/16 1 31/32 21/32 23/64 1/8 3/32 4.0
25 02 140 5 1/2
black atramentized
polished with multi-component grips
3/32 1/16 1 21/32 19/32 5/16 3/32 5/64 3.8
25 02 160 6 1/4 3/32 1/16 1 31/32 21/32 23/64 1/8 3/32 5.1
25 08 160 sba 6 1/4
black atramentized
polishedinsulated with multi-com-ponent grips, VDE-tested
3/32 1/16 1 31/32 21/32 23/64 1/8 3/32 5.1
25 21 160 6 1/440°
black atramentized
polished plastic coated 3/32 1/16 1 31/32 29/32 21/32 23/64 1/8 3/32 4.0
Cutting capacities DimensionsProduct Number mm
Pliers Head Handles
Ø mm Ø mm
L3mm
L4mm
W3mm
T1mm
W4mm
T2mm Ounces
25 01 125 125 black
atramentizedpolished plastic coated
2.2 1.6 27.0 13.0 7.0 2.5 1.8 2.6
25 01 140 140 2.5 1.6 42.0 15.0 8.0 2.5 2.0 3.1
25 01 160 160 2.5 1.6 50.0 16.5 9.0 3.0 2.5 4.0
25 02 140 140
black atramentized
polished with multi-component grips
2.5 1.6 42.0 15.0 8.0 2.5 2.0 3.8
25 02 160 160 2.5 1.6 50.0 16.5 9.0 3.0 2.5 5.1
25 08 160 sba 160
black atramentized
polishedinsulated with multi-component grips, VDE-tested
2.5 1.6 50.0 16.5 9.0 3.0 2.5 5.1
25 21 160 16040°
black atramentized
polished plastic coated 2.5 1.6 50.0 23.0 16.5 9.0 3.0 2.5 4.0
25 08 160 sba
38
griPPing Pliers
26snipe nose side Cutting Pliers (stork beak pliers)
ISO 5745
26 11 200
26 22 20040°
■ resilient precision tips snap back into place even after being twisted■ half-round, long, pointed jaws ■ with additionally hardened cutting edges (hardness approx. 61 HRC)
for soft, medium hard and hard wire ■ Vanadium electric steel; forged, oil-hardened
Cutting capacities DimensionsProduct Number inch
Pliers Head Handles
Ø inch Ø inch
L3inch
L4inch
T1inch
W3inch
W4inch
T2inch Ounces
26 11 200 8
black atramentized
polished plastic coated 1/8 3/32 2 7/8 3/8 11/16 1/8 3/32 6.0
26 11 200 s1 8 polished plastic coated 1/8 3/32 2 7/8 3/8 11/16 1/8 3/32 6.0
26 18 200 sba 8
black atramentized
polishedinsulated with multi-com-ponent grips, VDE-tested
1/8 3/32 2 7/8 3/8 11/16 1/8 3/32 6.0
26 12 200 8 black atramentized
polished with multi-component grips
1/8 3/32 2 7/8 3/8 11/16 1/8 3/32 7.1
26 21 200 840° black
atramentized polished plastic coated 1/8 3/32 2 7/8 29/32 3/8 11/16 1/8 3/32 6.0
26 28 200 sba 840°
black atramentized
polishedinsulated with multi-com-ponent grips, VDE-tested
1/8 3/32 2 7/8 29/32 3/8 11/16 1/8 3/32 6.0
26 22 200 840°
black atramentized
polished with multi-component grips
1/8 3/32 2 7/8 29/32 3/8 11/16 1/8 3/32 6.9
Cutting capacities DimensionsProduct Number mm
Pliers Head Handles
Ø mm Ø mm
L3mm
L4mm
T1mm
W3mm
W4mm
T2mm Ounces
26 11 200 200
black atramentized
polished plastic coated 3.2 2.2 73.0 9.5 17.5 3.0 2.5 6.0
26 11 200 s1 200 polished plastic coated 3.2 2.2 73.0 9.5 17.5 3.0 2.5 6.0
26 18 200 sba 200
black atramentized
polishedinsulated with multi-com-ponent grips, VDE-tested
3.2 2.2 73.0 9.5 17.5 3.0 2.5 6.0
26 12 200 200 black atramentized
polished with multi-component grips
3.2 2.2 73.0 9.5 17.5 3.0 2.5 7.1
26 21 200 200 40° black
atramentized polished plastic coated 3.2 2.2 73.0 23.0 9.5 17.5 3.0 2.5 6.0
26 28 200 sba 20040°
black atramentized
polishedinsulated with multi-com-ponent grips, VDE-tested
3.2 2.2 73.0 23.0 9.5 17.5 3.0 2.5 6.0
26 22 200 20040°
black atramentized
polished with multi-component grips
3.2 2.2 73.0 23.0 9.5 17.5 3.0 2.5 6.9
elastic tips: stable even when twisted
26 11 200 s1
26 18 200 sba
39
griPPing Pliers
28assembly Pliers ISO 5743
28 01 200
28 21 200
■ suitable for gripping and assembly work ■ serrated gripping surfaces ■ High-grade special tool steel; forged, oil-hardened
DimensionsProduct Number inch mm
Pliers Head Handles L3inch
W3inch
T1inch
W4inch
T2inch
L3mm
W3mm
T1mm
W4mm
T2mm Ounces
28 01 200 8 200 black atramentized polishedplastic coated
1 19/64 17/32 13/32 5/32 13/32 33.0 13.5 10.5 4.0 10.5 6.9
28 21 200 8 200 black atramentized polished plastic coated
1 11/32 17/32 13/32 1/8 1/8 34.0 13.5 10.5 3.0 3.0 6.6
29Telephone Pliers ISO 5745
29 11 160
■ cross-hatched gripping surfaces, knurled
■ Chrome vanadium electric steel; forged, oil-hardened
style 2extra slim, fine tips; also suitable for soldering work
DimensionsProduct Number inch mm
Style Pliers Head Handles L3inch
W3inch
T1inch
W4inch
T2inch
L3mm
W3mm
T1mm
W4mm
T2mm Ounces
29 11 160 6 1/4 160 1black atramentized
polishedplastic coated
2 11/64 35/64 5/16 3/32 21/64 55.0 14.0 8.0 2.5 8.5 3.6
29 21 160 6 1/4 160 2 black atramentized
polished plastic coated
2 1/8 35/64 23/64 5/64 5/64 54.0 14.0 9.0 2.0 2.0 4
40
griPPing Pliers
31gripping Pliers (needle-nose pliers)
ISO 5743
31 11 160
■ precision pliers for assembly, bending and adjusting work ■ with extra long jaws: length of jaws 2 11/64“■ smooth gripping surfaces■ smooth edges■ Chrome vanadium electric steel; forged, oil-hardened
DimensionsProduct Number inch mm
Pliers Head Handles L3inch
L4inch
W3inch
T1inch
W4inch
T2inch Ounces
31 11 160 6 1/4 160 black atramentized polished plastic coated 2 11/64 5/8 19/64 5/64 3/32 3.5
31 21 160 6 1/4 160 45° black atramentized polished plastic coated 2 11/64 1 1/16 5/8 19/64 5/64 3/32 3.4
DimensionsProduct Number inch mm
Pliers Head Handles L3mm
L4mm
W3mm
T1mm
W4mm
T2mm Ounces
31 11 160 6 1/4 160 black atramentized polished plastic coated 55.0 16.0 7.5 2.0 2.5 3.5
31 21 160 6 1/4 160 45° black atramentized polished plastic coated 55.0 27.0 16.0 7.5 2.0 2.5 3.4
30 41 160
■ for the installation of wedge bulb lamps ■ plastic coated gripping surfaces ■ Chrome vanadium electric steel; forged, oil-hardened
Product Number inch mm
Pliers Head Handles
Ounces
30 41 160 6 1/4 160 black atramentized polished plastic coated 4.2
3041 halogen bulb exchange Pliers
41
griPPing Pliers
30long nose Pliers ISO 5745
■ heavy duty gripping pliers ■ different jaw styles for a wide range of applications■ Chrome vanadium electric steel; forged, oil-hardened
style 1long, trapezoidal jaws; serrated gripping surfaces
style 2long, half-round jaws; serrated gripping surfaces
style 3long, round jaws; smooth gripping surfaces
DimensionsProduct Number inch mm
Style Pliers Head Handles L3inch
W3inch
T1inch
W4inch
T2inch
L3mm
W3mm
T1mm
W4mm
T2mm Ounces
30 11 190 7 1/2 190 1black atramentized
polished plastic coated 1 3/32 47/64 3/8 1/8 9/32 50.0 18.5 9.5 3.0 7.0 4.9
30 16 160 6 1/4 160
1chrome plated
insulated with multi-component grips, VDE-tested
1 3/32 21/32 3/8 1/8 3/32 50.0 16.5 9.5 3.0 2.5 5.3
30 21 160 6 1/4 160 2black atramentized
polished plastic coated 1 3/32 21/32 3/8 1/8 3/32 50.0 16.5 9.5 3.0 2.5 4.3
30 31 140 5 1/2 140 3
black atramentized
polished plastic coated 1 31/64 19/32 5/16 5/32 5/64 37.5 15.0 8.0 4.0 2.0 2.9
30 31 160 6 1/4 160 1 19/32 21/32 3/8 13/64 3/32 41.0 16.5 9.5 5.0 2.5 3.9
30 36 160 6 1/4 160
3chrome plated
insulated with multi-component grips, VDE-tested
1 19/32 21/32 3/8 13/64 3/32 41.0 16.5 9.5 5.0 2.5 5.0
30 36 160
30 11 190
30 21 160
42
griPPing Pliers
32Relay adjusting Pliers ISO 5235
32 21 135
■ for gripping small wires and bending contact and relay springs
■ polished gripping surfaces ■ smooth edges ■ Chrome vanadium electric steel;
forged, oil-hardened
DimensionsProduct Number inch mm
Pliers Head Handles L3inch
W3inch
T1inch
W4inch
T2inch
L3mm
W3mm
T1mm
W4mm
T2mm Ounces
32 21 135 5 1/4 135 black atramentized polished plastic coated
1 11/32 1/2 9/32 1/16 9/64 34.0 12.5 7.0 1.4 3.5 2.6
32 31 135 5 1/4 13540°
black atramentized polished
plastic coated
1 17/64 1/2 9/32 1/16 9/64 32.0 12.5 7.0 1.4 3.5 2.6
33Duckbill Pliers ISO 5743
33 01 160
■ duckbill shaped jaws 23/64“ wide at the tip and tapering to 1/16“ thickness
■ smooth gripping surfaces ■ Chrome vanadium electric steel;
forged, oil-hardened
DimensionsProduct Number inch mm
Pliers Head Handles L3inch
W3inch
T1inch
W4inch
T2inch
L3mm
W3mm
T1mm
W4mm
T2mm Ounces
33 01 160 6 1/4 160 black atramentized polishedplastic coated
2 11/64 19/32 19/64 1/8 23/64 55.0 15.0 7.5 3.0 9.0 3.6
33 03 160 6 1/4 160 chrome plated plastic coated
2 11/64 19/32 19/64 1/8 23/64 55.0 15.0 7.5 3.0 9.0 3.6
32 31 135
40°
43
griPPing Pliers
34 Precision electronics gripping Pliers ISO 9655
34 12 130
34 22 130
34 32 130
The subtle differenceKNIPEX precision electronics pliers are made of high-quality ball bearing steel and processed with the highest degree of care. Each movement is gentle and even and there is no backlash. Each work step proceeds reliably and precisely. This makes work much easier for professionals.
■ for very precise assembly work, e.g. in electronics and fine mechanics ■ for gripping, holding and bending ■ smooth gripping surfaces; smooth edges ■ approx. 20% lighter than conventional electronics pliers ■ bolted joint and carefully manufactured joint surfaces for even,
low-friction movement throughout the entire opening range ■ double spring for a gentle and even opening ■ ergonomically optimized handle covers ■ Chrome vanadium ball-bearing steel; forged
style 1flat, wide jaws
style 2half-round jaws
style 3round, pointed jaws
DimensionsProduct Number inch
Style Pliers Head Handles Binch
Ainch
Dinch
Einch
Finch Ounces
34 12 130 5 1/4 1 burnished polished with multi-component grips 55/64 7/16 17/64 1/16 9/64 2.2
34 22 130 5 1/4 2 burnished polished with multi-component grips 57/64 7/16 17/64 1/16 1/16 2.2
34 32 130 5 1/4 3 burnished polished with multi-component grips 15/16 7/16 17/64 5/64 3/64 2.1
DimensionsProduct Number mm
Style Pliers Head Handles Bmm
Amm
Dmm
Emm
Fmm Ounces
34 12 130 135 1 burnished polished with multi-component grips 21.9 11.2 6.5 1.4 3.5 2.2
34 22 130 135 2 burnished polished with multi-component grips 22.7 11.2 6.5 1.6 1.6 2.2
34 32 130 135 3 burnished polished with multi-component grips 23.7 11.2 6.5 2.0 1.0 2.1
Pliers sets
see page 182
44
griPPing Pliers
34Precision electronics gripping Pliers esD ISO 9655
34 12 130 esD
34 22 130 esD
34 32 130 esD
esD pliers (electrostatic discharge)■ electrostatic energy is discharged through the handles in a
gradual and controlled manner■ protects components endangered by electrostatic discharge■ in accordance with applicable standards,
e.g. IEC TR 61 340-5, DIN EN 61 340-5, SP Method 2472
■ for very precise assembly work, e.g. in electronics and fine mechanics ■ for gripping, holding and bending ■ electrically discharging handles – dissipative ■ smooth gripping surfaces; smooth edges ■ approx. 20% lighter than conventional electronics pliers ■ bolted joint and carefully manufactured joint surfaces for even,
low-friction movement throughout the entire opening range ■ double spring for a gentle and even opening ■ ergonomically optimized handle covers ■ Chrome vanadium ball-bearing steel; forged
style 1flat, wide jaws
style 2half-round jaws
style 3round, pointed jaws
DimensionsProduct Number inch
Style Pliers Head Handles Binch
Ainch
Dinch
Einch
Finch Ounces
34 12 130 esD 5 1/4 1 burnished polished with multi-component grips 55/64 7/16 17/64 1/16 3/32 2.2
34 22 130 esD 5 1/4 2 burnished polished with multi-component grips 57/64 7/16 17/64 1/16 1/16 2.3
34 32 130 esD 5 1/4 3 burnished polished with multi-component grips 15/16 7/16 17/64 5/64 3/64 2.2
DimensionsProduct Number mm
Style Pliers Head Handles Bmm
Amm
Dmm
Emm
Fmm Ounces
34 12 130 esD 135 1 burnished polished with multi-component grips 21.9 11.2 6.5 1.4 3.5 2.2
34 22 130 esD 135 2 burnished polished with multi-component grips 22.7 11.2 6.5 1.6 1.6 2.3
34 32 130 esD 135 3 burnished polished with multi-component grips 23.7 11.2 6.5 2.0 1.0 2.2
Pliers sets
see page 182
45
griPPing Pliers
35 electronics Pliers ISO 9655
35 11 115
35 22 115
35 32 115
35 42 115
45°
35 52 145
■ precision pliers for ultra fine assembly work, e.g. in electronics and fine mechanics
■ for gripping, holding and bending ■ precision box joint ■ smooth gripping surfaces ■ smooth edges■ low-friction double spring for gentle and even opening ■ the polish with a fine film of oil offers effective rust protection –
no circuit faults caused by peeling chrome from plated tools ■ Special tool steel; forged, oil-hardened
35 62 145
35 72 145
35 82 145
45°
DimensionsProduct Number inch mm
Head Handles Binch
Ainch
Dinch
Einch
Finch
Bmm
Amm
Dmm
Emm
Fmm
Ounces
35 11 115 4 1/2 115 polished plastic coated 57/64 3/8 17/64 5/64 5/32 22.5 9.5 6.5 2.0 4.0 2.2
35 12 115 4 1/2 115 mirror polished
with multi- component grips
57/64 3/8 17/64 5/64 5/32 22.5 9.5 6.5 2.0 4.0 2.5
35 21 115 4 1/2 115 polished plastic coated 57/64 3/8 17/64 5/64 1/16 22.5 9.5 6.5 2.0 1.5 2.1
35 22 115 4 1/2 115 mirror polished
with multi- component grips
57/64 3/8 17/64 5/64 1/16 22.5 9.5 6.5 2.0 1.5 2.6
35 31 115 4 1/2 115 polished plastic coated 57/64 3/8 17/64 5/64 3/64 22.5 9.5 6.5 2.0 1.0 2.0
35 32 115 4 1/2 115 mirror polished
with multi- component grips
57/64 3/8 17/64 5/64 3/64 22.5 9.5 6.5 2.0 1.0 2.5
35 42 115 4 1/2 115 45° mirror polished
with multi- component grips
57/64 3/8 17/64 5/64 1/16 22.5 9.5 6.5 2.0 1.5 2.6
35 52 145 5 3/4 145 mirror polished
with multi- component grips
1 37/64 15/32 19/64 1/16 5/32 40.0 12.0 7.5 1.5 4.0 3.6
35 62 145 5 3/4 145 mirror polished
with multi- component grips
1 37/64 15/32 19/64 3/32 1/16 40.0 12.0 7.5 2.5 1.5 3.6
35 72 145 5 3/4 145 mirror polished
with multi- component grips
1 37/64 15/32 19/64 3/32 3/64 40.0 12.0 7.5 2.5 1.3 3.5
35 82 145 5 3/4 145 45° mirror polished
with multi- component grips
1 3/8 15/32 19/64 3/32 3/64 35.0 12.0 7.5 2.5 1.0 3.6
Pliers sets
see page 182
46
griPPing Pliers
35electronics Pliers esD ISO 9655
35 12 115 esD
35 22 115 esD
35 42 115 esD
45°
■ precision pliers for ultra fine assembly work, e.g. in electronics and fine mechanics
■ for gripping, holding and bending ■ electrically discharging handles – dissipative ■ precision box joint ■ smooth gripping surfaces ■ smooth edges■ low-friction double spring for gentle and even opening ■ the mirror polish together with a fine film of oil offers effective
rust protection – no circuit faults caused by peeling chrome from plated tools
■ with two-color dual component handles, black/grey ■ Special tool steel; forged, oil-hardened
DimensionsProduct Number inch mm
Head Handles Binch
Ainch
Dinch
Einch
Finch
Bmm
Amm
Dmm
Emm
Fmm Ounces
35 12 115 esD 4 1/2 115 mirror polished
with multi- component grips
57/64 3/8 17/64 5/64 5/32 22.5 9.5 6.5 2.0 4.0 2.6
35 22 115 esD 4 1/2 115
mirror polished with multi- component grips
57/64 3/8 17/64 5/64 1/16 22.5 9.5 6.5 2.0 1.5 2.6
35 42 115 esD 4 1/2 115 45°
mirror polished with multi- component grips
57/64 3/8 17/64 5/64 1/16 22.5 9.5 6.5 2.0 1.5 2.6
Pliers sets
see page 182
esD pliers (electrostatic discharge)■ electrostatic energy is discharged through the handles in a
gradual and controlled manner■ protects components endangered by electrostatic discharge■ in accordance with applicable standards,
e.g. IEC TR 61 340-5, DIN EN 61 340-5, SP Method 2472
47
griPPing Pliers
36electronics mounting Pliers ISO 5743
36 12 130
36 22 125
36 32 125
■ precision pliers for very fine assembly and repair work in electronics
■ for bending and cutting off wire ends on components
■ precision box joint ■ smooth gripping surfaces ■ smooth edges■ low-friction double spring for
gentle and even opening ■ the mirror polish together with
a fine film of oil offers effective rust protection – no circuit faults caused by peeling chrome from plated tools
■ High-grade special tool steel; forged, oil-hardened
36 12 130to bend wire in shape for the distance to the plate
Cutting capacities DimensionsProduct Number inch
Head Handles
Ø inch
L3inch
Winch
T1inch
W1inch
T2inch Ounces
36 12 130 5 1/4 mirror polished with multi-component grips 29/32 15/32 3/8 7/32 15/64 3.3
36 22 125 5 mirror polished with multi-component grips 3/64 23/32 29/64 19/64 19/64 3/32 3.3
36 32 125 5 mirror polished with multi-component grips 3/64 23/32 29/64 19/64 19/64 5/32 3.8
Cutting capacities DimensionsProduct Number mm
Head Handles
Ø mm
L3mm
Wmm
T1mm
W1mm
T2mm Ounces
36 12 130 130 mirror polished with multi-component grips 23.0 12.0 9.5 5.5 6.0 3.3
36 22 125 125 mirror polished with multi-component grips 1.2 18.0 11.5 7.5 7.5 2.6 3.3
36 32 125 125 mirror polished with multi-component grips 1.0 18.0 11.5 7.5 7.5 4.0 3.8
36 22 125to bend and cut wire at 1/16“ length below the plate
36 32 125to crunch and cut wire at 1/16“ length below the plate
48
griPPing Pliers
37gripping Pliers for precision mechanics
ISO 9655
37 11 125
37 21 125
37 31 125
■ precision pliers for ultra fine assembly work, e.g. in electronics and fine mechanics
■ for gripping, holding, bending and adjusting ■ precision tips ■ smooth gripping surfaces ■ smooth edges■ lap joint ■ Chrome vanadium electric steel; forged, oil-hardened
style 1flat, wide jaws
style 2flat, concave and pointed jaws
style 3half-round jaws
style 4round, pointed jaws to bend wire loops
DimensionsProduct Number inch
Style Pliers Head Handles Binch
Ainch
Dinch
Einch
Finch Ounces
37 11 125 5 1 black atramentized polished plastic coated 1 1/16 31/64 9/32 5/64 7/32 2.7
37 21 125 5 2 black atramentized polished plastic coated 1 1/16 31/64 9/32 5/64 5/64 2.6
37 31 125 5 3 black atramentized polished plastic coated 1 1/16 31/64 9/32 5/64 1/16 2.6
37 43 125 5 4 chrome plated plastic coated 1 1/16 37/64 5/16 5/64 3/64 2.7
DimensionsProduct Number mm
Style Pliers Head Handles Bmm
Amm
Dmm
Emm
Fmm Ounces
37 11 125 125 1 black atramentized polished plastic coated 27.0 12.5 7.0 2.0 5.5 2.7
37 21 125 125 2 black atramentized polished plastic coated 27.0 12.5 7.0 2.0 2.0 2.6
37 31 125 125 3 black atramentized polished plastic coated 27.0 12.5 7.0 2.0 1.6 2.6
37 43 125 125 4 chrome plated plastic coated 27.0 14.5 8.0 2.0 1.0 2.7
37 43 125
49
griPPing Pliers
38 mechanics‘ Pliers ISO 5745
38 11 200
38 21 20040°
38 31 200
38 41 190
38 71 20070°
38 91 20045°
■ high-strength jaws and tips bend and snap back into place easily – no deformation
■ cross-hatched gripping surfaces, knurled ■ Vanadium electric steel; forged, oil-hardened
style 945° angled, half-round, long jaws, also suitable for gripping spark plug covers and round components
DimensionsProduct Number inch mm
Style Pliers Head Handles L3inch
W3inch
T1inch
W4inch
T2inch
L3mm
W3mm
T1mm
W4mm
T2mm
Ounces
38 11 200 8 200 1black atramentized
polishedplastic coated
2 7/8 11/16 3/8 1/8 3/32 73.0 17.5 9.5 3.0 2.5 6.3
38 21 200 8 200 40° 2black atramentized
polishedplastic coated
2 7/8 11/16 3/8 1/8 3/32 73.0 17.5 9.5 3.0 2.5 6.2
38 31 200 8 200 3black atramentized
polishedplastic coated
2 7/8 11/16 3/8 1/8 3/32 73.0 17.5 9.5 3.0 2.5 6.2
38 35 200 8 200 3 chrome plated
with multi-component grips
2 7/8 11/16 3/8 1/8 3/32 73.0 17.5 9.5 3.0 2.5 7.2
38 41 190 7 1/2 190 4black atramentized
polishedplastic coated
1 31/32
23/32 5/16 5/64 5/16 50.0 18.0 8.0 2.0 8.0 4.9
38 71 200 8 200 70° 7black atramentized
polishedplastic coated
2 7/8 11/16 3/8 1/8 5/64 73.0 17.5 9.5 3.0 2.0 6.1
38 91 200 8 200 45° 9 black atramentized
polished plastic coated
2 7/8 11/16 3/8 3/32 73.0 17.5 9.5 2.5 6.0
style 770° angled, half-round jaws, suitable for pulling split pins; for gripping at points that are difficult to access
50
griP Pliers
40universal grip Pliers
40 04 250
41grip Pliers
41 04 250
41 14 250
41 34 165
■ tightly holds round or flat material■ heavy duty■ with adjustment screw and release lever ■ one-handed operation ■ high clamping pressure due to toggle lever action ■ pliers body: rolled steel; high-strength, forged, oil-hardened ■ gripping jaws: Chrome vanadium electric steel; forged
Product Number inch mm inch inch inch mm mm mm Ounces
40 04 180 7 1/4 180 1 3/8 63/64 1 1/4 35.0 25.0 32.0 10.9
40 04 250 10 250 1 3/8 1 3/16 1 1/4 35.0 30.0 32.0 18.4
■ tightly holds round or flat material ■ heavy duty■ with adjustment screw and release lever ■ one-handed operation ■ high clamping pressure due to toggle lever action ■ pliers body: rolled steel; high-strength, forged, oil-hardened ■ gripping jaws: Chrome vanadium electric steel; forged
style 0jaws for round workpieces; with wire cutter
style 1jaws with double prism for round, section and flat material
style 3long nose grip pliers; narrow, long jaws
Product Number inch mm
Style Pliers
inch inch inch mm mm mm Ounces
41 04 180 7 1/4 180
0 nickel plated
1 3/16 51/64 1 3/16 30.0 20.0 30.0 12.8
41 04 250 10 250 1 37/64 51/64 1 3/16 40.0 20.0 30.0 18.2
41 04 300 12 300 2 19/32 1 3/16 1 11/32 65.0 30.0 34.0 32.6
41 14 250 10 250 1 nickel plated 1 27/64 1 27/64 1 27/64 36.0 36.0 36.0 19.6
41 34 165 6 1/4 165 3 nickel plated 51/64 25/64 15/16 20.0 10.0 24.0 6.7
51
52
circliP Pliers
44Circlip Pliers for internal circlips on bore holes
44 11 J2
44 21 J21
90°
44 31 J22
45°
style 1DIN 5256 C, straight tips
style 2DIN 5254 B; 90° angled tips
style 345° angled tips
Pliers sets
see page 176
■ for fitting circlips on bore holes, range of application from 5/16“ - 5 33/64“ dia.
■ solid style, forged ■ non-slip, solid tips ■ pliers body and tips:
Chrome vanadium steel; forged, oil-hardened
Size of boreØ inch
Size of boreØ mm
Product Number inch mm
Style Pliers Head Handles
Ounces
44 11 J0 5 3/4 140
1 black atramentized polished plastic coated
5/16 - 33/64 8 - 13 3.1
44 11 J1 5 3/4 140 15/32 - 63/64 12 - 25 3.1
44 11 J2 8 180 3/4 - 2 23/64 19 - 60 4.8
44 11 J3 9 225 1 37/64 - 3 15/16 40 - 100 6.9
44 11 J4 12 3/4 320 3 23/64 - 5 33/64 85 - 140 16.5
44 21 J01 5 1/4 130
90° 2 black atramentized polished plastic coated
5/16 - 33/64 8 - 13 3.1
44 21 J11 5 1/4 130 15/32 - 63/64 12 - 25 3.1
44 21 J21 6 3/4 170 3/4 - 2 23/64 19 - 60 4.9
44 21 J31 8 1/2 215 1 37/64 - 3 15/16 40 - 100 6.9
44 21 J41 12 300 3 23/64 - 5 33/64 85 - 140 16.3
44 31 J02 5 3/4 140
45° 3 black atramentized polished plastic coated
5/16 - 33/64 8 - 13 3.2
44 31 J12 5 3/4 140 15/32 - 63/64 12 - 25 3.2
44 31 J22 8 180 3/4 - 2 23/64 19 - 60 4.9
44 31 J32 9 225 1 37/64 - 3 15/16 40 - 100 6.9
44 31 J42 12 310 3 23/64 - 5 33/64 85 - 140 16.4
53
circliP Pliers
46Circlip Pliers for external circlips on shafts
46 11 a2
46 21 a21
90°
46 31 a22
45°
style 1DIN 5254 A; straight tips
style 2DIN 5254 B; 90° angled tips
style 345° angled tips
Pliers sets
see page 176
■ for fitting circlips on shafts, range of application from 1/8“ - 5 33/64“ dia.
■ solid style, forged ■ non-slip, solid tips ■ pliers body and tips:
Chrome vanadium steel; forged, oil-hardened
Size of shaftØ inch
Size of shaftØ mm
Product Number inch mm
Style Pliers Head Handles
Ounces
46 11 a0 5 3/4 140
1 black atramentized polished plastic coated
1/8 - 25/64 3 - 10 3.0
46 11 a1 5 3/4 140 25/64 - 63/64 10 - 25 3.0
46 11 a2 8 180 3/4 - 2 23/64 19 - 60 4.7
46 11 a3 8 1/4 210 1 37/64 - 3 15/16 40 - 100 7.8
46 11 a4 12 3/4 320 3 23/64 - 5 33/64 85 - 140 17.8
46 21 a01 5 125
90° 2 black atramentized polished plastic coated
1/8 - 25/64 3 - 10 3.0
46 21 a11 5 125 25/64 - 63/64 10 - 25 3.0
46 21 a21 6 3/4 170 3/4 - 2 23/64 19 - 60 4.7
46 21 a31 8 200 1 37/64 - 3 15/16 40 - 100 7.7
46 21 a41 12 300 3 23/64 - 5 33/64 85 - 140 18.0
46 31 a02 5 1/4 130
45° 3 black atramentized polished plastic coated
1/8 - 25/64 3 - 10 2.9
46 31 a12 5 1/4 130 25/64 - 63/64 10 - 25 3.0
46 31 a22 7 1/4 185 3/4 - 2 23/64 19 - 60 4.7
46 31 a32 8 1/4 210 1 37/64 - 3 15/16 40 - 100 7.5
46 31 a42 12 310 3 23/64 - 5 33/64 85 - 140 18.0
54
circliP Pliers
44Circlip Pliers for large internal circlips
44 10 J6
style 1DIN 5256 C, straight tips
style 2DIN 5256 D; 90° angled tips
45
45 10 170
45 21 200
30°
45 10 170 45 21 200 45 21 200
Size of boreØ inch
Size of boreØ mm
Product Number inch mm
Style Pliers
Ounces
44 10 J5 22 1/4 570 1 black powder-coated
4 51/64 - 11 13/16 122 - 300 61.0
44 10 J6 22 580 9 59/64 - 15 3/4 252 - 400 62.0
44 20 J51 23 1/4 590 90° 2 black powder-coated
4 51/64 - 11 13/16 122 - 300 64.0
44 20 J61 23 1/2 600 9 59/64 - 15 3/4 252 - 400 61.0
44 19 J6 1 pair of spare tips for 44 10 J6
■ for assembling circlips in bore holes within the range of 4 51/64“ - 15 3/4“ dia.
■ with locking device – can be released without completing cycle■ with replaceable tips made of tempered steel ■ black powder-coated ■ pliers body: rolled steel, high-strength ■ tips: Special tool steel; rolled, oil-hardened
special Retaining Ring Pliers for retaining rings on shafts
ISO 5743
■ for fitting horseshoe-shaped spring retaining rings and circlips without grip holes
■ for shaft retaining devices ■ with opening spring ■ Chrome vanadium electric steel; forged, oil-hardened
45 10 170for retaining rings with a minimum ring split gap of 9/64“
45 21 200anlged jaws with centering hole; for retaining rings from 15/36“ dia., e.g. for securing drive shaft in the gearbox of a motor vehicle; minimum ring split gap of the rings 3/32“
Product Number inch mm
Pliers Handles
Ounces
45 10 170 6 3/4 170 burnished 5.5
45 21 200 8 200 30° burnished plastic coated 6.6
55
circliP Pliers
46Circlip Pliers for large external circlips
46 10 a5
style 1DIN 5254 A; straight tips
style 2DIN 5254 B; 90° angled tips
46Circlip Pliers for grip rings on shafts
ISO 5743
46 11 g0
46 11 g2
■ for assembling circlips on shafts within the range of 4 51/64“ - 15 3/4“ dia.
■ with locking device – can be released without completing cycle■ with replaceable tips made of tempered steel ■ black powder-coated ■ pliers body: rolled steel, high-strength ■ tips: Special tool steel; rolled, oil-hardened
Size of shaftØ inch
Size of shaftØ mm
Product Number inch mm
Style Pliers
Ounces
46 10 a5 22 1/2 560 1 black powder-coated
4 51/64 - 11 13/16 122 - 300 62.5
46 10 a6 22 3/4 570 9 59/64 - 15 3/4 252 - 400 63.3
46 20 a51 22 3/4 570 90° 2 black powder-coated
4 51/64 - 11 13/16 122 - 300 65.0
46 20 a61 22 3/4 580 9 59/64 - 15 3/4 252 - 400 64.4
■ for fitting grip rings on shafts from 1/16“ - 1 3/16“ dia. ■ with opening spring ■ solid style, forged ■ non-slip, solid tips ■ pliers body and tips: Chrome vanadium stainless steel;
forged, oil-hardened
46 11 g0for rings of 1/16“ - 1 3/16“dia., with adjustable stop screw to prevent overstretching
Size of shaftØ inch
Size of shaftØ mm
Product Number inch mm
Pliers Head Handles
Ounces
46 11 g0 5 1/2 140 black atramentized polished plastic coated 1/16 - 5/36 1.5 - 4.0 3.1
46 11 g1 5 1/2 140
black atramentized polished plastic coated
5/32 - 9/32 4.0 - 7.0 3.0
46 11 g2 5 1/2 140 13/64 - 33/64 5.0 - 13.0 3.0
46 11 g3 5 1/2 140 35/64 - 23/32 14.0 - 18.0 3.0
46 11 g4 7 1/4 180 51/64 - 1 3/16 20.0 - 30.0 4.7
56
Tip-top qualityEasy and reliable assembly: form-fitting inserted and pressed-in tips made of high-density spring steel offer a high level of protection against excessive stress and strain, e.g. when removing rings that are stuck. The large supporting surfaces and the position of the tips make it more difficult for the rings to fly off.
circliP Pliers
48
48 11 J2
48 21 J21
90°
Precision and durability
High-density spring steel with a score-free surface is used for the tips. This increases the tips‘ resistance to dynamic and static strain. The tips are 30% more stable than conventional pliers when subjected to one-off overloading, while still allowing good accessibility during assembly. Subjected to dynamic strain, the tips‘ resistance capacity is up to 10 times greater! The tips on the Precision Circlip Pliers are non-detachable!
style 1DIN 5256 C, straight tips
style 2DIN 5256 D; 90° angled tips
Sturdy, inserted tips: made from high-density spring steel
Slim head shape Tight fit through compression
Pliers sets
see page 176
Precision Circlip Pliers for internal circlips in bore holes
With inserted tips for reliable work
■ heavy duty for continuous operation: up to 10 times longer service life than turned tips
■ bolted joint: precise, zero backlash operation of pliers ■ non-slip plastic coating on the handles ■ pliers body: Chrome vanadium electric steel; forged, oil-hardened ■ inserted tips: spring steel wire, drawn
Size of boreØ inch
Size of boreØ mm
Tips ØProduct Number inch mm
Style Pliers Handles inch mm
Ounces
48 11 J0 5 3/4 140
1 grey atramentized plastic coated
5/16 - 33/64 8 - 13 3/64 0.90 3.7
48 11 J1 5 3/4 140 15/32 - 63/64 12 - 25 3/64 1.25 3.7
48 11 J2 8 180 3/4 - 2 23/64 19 - 60 5/64 1.80 6.2
48 11 J3 9 225 1 37/64 - 3 15/16 40 - 100 3/32 2.25 9.4
48 11 J4 12 3/4 320 3 23/64 - 5 33/64 85 - 140 1/8 3.20 20.5
48 21 J01 5 1/4 130
90° 2 grey atramentized plastic coated
5/16 - 33/64 8 - 13 3/64 0.90 3.7
48 21 J11 5 1/4 130 15/32 - 63/64 12 - 25 3/64 1.25 3.7
48 21 J21 6 1/2 165 3/4 - 2 23/64 19 - 60 5/64 1.80 6.2
48 21 J31 8 1/4 210 1 37/64 - 3 15/16 40 - 100 3/32 2.25 9.3
48 21 J41 12 305 3 23/64 - 5 33/64 85 - 140 1/8 3.20 20.3
57
Tight fit through compression
49 21 a21
90°
49 11 a2
Conventional Circlip Pliers: distortion of the circlip when being fitted is possible
Circlips are held securely: large contact faces and the position of the tips make it difficult for the circlip to bounce off
Style 3 / Style 4: With adjustable restricted opening
Precision Circlip Pliers for external circlips on shafts
circliP Pliers
Spring inside the joint: the spring isprotected inside the precisely bolted joint.It does not hinder work and cannot getdirty or lost.
KNIPEX Precision Circlip Pliers: fit circlips without distortion; easy and quick assembly
Size of shaftØ inch
Size of shaftØ mm
Tips ØProduct Number inch mm
Style Pliers Handles inch mm
Ounces
49 11 a0 5 3/4 140
1 grey atramentized plastic coated
1/8 - 25/64 3 - 10 3/64 0.90 3.6
49 11 a1 5 3/4 140 25/64 - 63/64 10 - 25 3/64 1.25 3.5
49 11 a2 8 180 3/4 - 2 23/64 19 - 60 5/64 1.80 6.0
49 11 a3 9 225 1 37/64 - 3 15/16 40 - 100 3/32 2.25 9.5
49 11 a4 12 3/4 320 3 22/64 - 5 33/64 85 - 140 1/8 3.20 21.0
49 21 a01 5 1/4 130
90° 2 grey atramentized plastic coated
1/8 - 25/64 3 - 10 3/64 0.90 3.5
49 21 a11 5 1/4 130 25/64 - 63/64 10 - 25 3/64 1.25 3.6
49 21 a21 6 1/2 165 3/4 - 2 23/64 19 - 60 5/64 1.80 5.6
49 21 a31 8 1/4 210 1 37/64 - 3 15/16 40 - 100 3/32 2.25 9.6
49 21 a41 12 305 3 22/64 - 5 33/64 85 - 140 1/8 3.20 21.249 31 a0 5 3/4 140 3 grey atramentized plastic coated 1/8 - 25/64 3 - 10 3/64 0.90 3.649 41 a01 5 1/4 130 90° 4 grey atramentized plastic coated 1/8 - 25/64 3 - 10 3/64 0.90 3.6
■ heavy duty for continuous operation: up to 10 times longer service life than turned tips
■ large contact faces on the tips: no distortion of circlips, easy fitting ■ joint with screw: precise, zero-backlash operation of pliers ■ internal opening spring, protected ■ non-slip plastic coating on the handles ■ pliers body: Chrome vanadium electric steel; forged, oil-hardened ■ inserted tips: spring steel wire, drawn
49 31 a0 / style 3with additional opening limiter (continuously adjustable opening area); avoids overstretching of small external circlips; DIN 5254 A; straight tips
49 41 a01 / style 4with additional opening limiter (continuously adjustable opening area); avoids overstretching of small external circlips; DIN 5254 B; 90° angled tips
style 1DIN 5254 A, straight tips
style 2DIN 5254 B; 90° angled tips
Bolted joint: high precision and smooth action
49
Pliers sets
see page 176
With inserted tips for reliable work
58
Circlip Tool for internal and external circlips
CiRCliP PlieRs
■ universally usable for large circlips with nominal diameters of 15 3/4“ - 39 3/8“
■ reliable opening and closing of the circlips and holding by self-locking precision spindle drive
■ for fitting and removing circlips in one operation ■ circlips are securely held thanks to short, direct attachment ■ replaceable tips with 15/64“ and 23/64“ diameters;
for perfect adaptation to the actuation bores in the circlips ■ optional operation with hexagonal key, ratchet wrench or cordless drill ■ areas of application e.g. wind turbines, tidal power stations, generator
construction, hydropower stations, large machine construction (rolling mills, presses), shipbuilding and aerospace – wherever very high forces and torques are transmitted with large shafts and bearings
■ tip material: Chrome vanadium electric steel
46
Manually operable Machine operableReplaceable inserts for internal and external circlips
Product Number
Size of boreØ inch
Size of boreØ mm
Size of shaftØ inch
Size of shaftØ mm Ounces
46 10 100 15 3/4 - 39 3/8 400 - 1,000 15 3/4 - 39 3/8 400 - 1,000 77.6
59
50Carpenters‘ Pincers ISO 9243
50 01 225
■ heavy duty ■ the Carpenters‘ Pincers preferred
by tradespeople■ wear-resistant■ cutting edges with additional
hardness; cutting edge hardness approx. 60 HRC
■ Special tool steel; forged, oil-hardened
Cutting capacitiesProduct Number inch mm
Pliers Head Handles
Ø inch Ø mm Ounces
50 01 160 6 1/4 160
black atramentized polished plastic coated
5/64 1.8 7.9
50 01 180 7 1/4 180 5/64 2.0 11.1
50 01 210 8 1/4 210 3/32 2.2 14.5
50 01 225 9 225 3/32 2.2 15.4
50 01 250 10 250 3/32 2.2 20.6
50 01 300 12 300 3/32 2.4 31.9
cArPenters‘ Pincers
55
55 00 300
Farriers‘ Pincers ISO 5743
■ the ideal pliers for the farrier ■ with small head and reversing
groove ■ also suitable for dismantling
work in vehicle body workshops ■ cutting edges with additional
hardness; cutting edge hardness approx. 59 HRC
■ Special tool steel; forged, oil-hardened
Head widthProduct Number inch mm
Pliers Head inch mm
Ounces
55 00 300 12 300 black atramentized polished 51/64 20.0 28.0
51Carpenters‘ Pincers ISO 9243
51 01 210
■ with striking face for driving in nails
■ cutting edges with additional hardness; cutting edge hardness approx. 60 HRC
■ Special tool steel; forged, oil-hardened
Product Number inch mm
Pliers Head Handles
Ounces
51 01 210 8 1/4 210 black atramentized
polishedplastic coated
14.6
60
concretors‘ niPPers
990 Concretors‘ nippers
ISO 9242
99 00 280
99 04 250
99 01 220
■ to twist and cut wire in one operation; fast, reliable and economical ■ unobtained precision and long service life make these the most
widely purchased concretors' nippers in the world ■ cutting edges with additional hardness;
cutting edge hardness approx. 61 HRC ■ High-grade special tool steel; forged, oil-hardened
Cutting capacitiesProduct Number inch mm
Pliers Head Handles
Ø inch Ø inch Ø mm Ø mm Ounces
99 00 200 8 200
black atramentized polished
5/64 1/16 1.8 1.4 8.1
99 00 220 8 3/4 220 3/32 1/16 2.4 1.6 11.1
99 00 250 10 250 3/32 1/16 2.4 1.6 11.8
99 00 280 11 280 7/64 5/64 2.8 1.8 16.0
99 00 300 12 300 1/8 5/64 3.1 1.8 18 .0
99 01 200 8 200
black atramentized polished plastic coated
5/64 1/16 1.8 1.4 8.7
99 01 220 8 3/4 220 3/32 1/16 2.4 1.6 11.8
99 01 250 10 250 3/32 1/16 2.4 1.6 15.1
99 01 280 11 280 7/64 5/64 2.8 1.8 17.6
99 01 300 12 300 1/8 5/64 3.1 1.8 19.3
57
57 00 360
Farriers‘ Pincers
ISO 5743
■ the ideal pliers for the farrier ■ suitable for dismantling work in vehicle body workshops ■ also for dismantling work with timber and metal ■ cutting edges with additional hardness;
cutting edge hardness approx. 59 HRC ■ Special tool steel; forged, oil-hardened
Head widthProduct Number inch mm
Pliers Head inch mm
Ounces
57 00 360 14 1/4 360 black atramentized polished 1 13/64 30.5 41.1
61
concretors‘ niPPers
991
99 10 250
99 10 300
99 11 300
99 14 250
99 14 300
25% reduction in required forcecompared to conventional concretor‘s pliers of the same size
high leverage Concretors‘ nippers high lever transmission
ISO 9242
■ for use when working with concrete steel and binding wire■ twists and cuts wire in one operation■ high leverage joint minimizes strain when working with thick wires■ extra slim design for reaching into deep or confined areas ■ high leverage design reduces strain on tendons and muscles■ cutting edge hardness approx. 61 HRC ■ High-grade special tool steel; forged, oil-hardened
Cutting capacities Head widthProduct Number inch mm
Pliers Head Handles
Ø inch Ø inch Ø mm Ø mm
inch mm
Ounces
99 10 250 10 250 black atramentized polished
1/8 5/64 3.3 1.8 29/32 23.0 12.3
99 10 300 12 300 5/32 5/64 3.8 2.0 63/64 25.0 17.7
99 11 250 10 250 black atramentized polished plastic coated
1/8 5/64 3.3 1.8 29/32 23.0 12.3
99 11 300 12 300 5/32 5/64 3.8 2.0 63/64 25.0 18.9
99 14 250 10 250 nickel plated
1/8 5/64 3.3 1.8 29/32 23.0 12.3
99 14 300 12 300 5/32 5/64 3.8 2.0 63/64 25.0 17.6
62
CuTTing PlieRs
61
61 01 20085°
Perfect for use when working with fencing
62electronics oblique Cutting nippers ISO 9654
62 12 120
15°
bolt end Cutting nippers high lever transmission ISO 5743
Powerful, compact, comfortable
■ features a greater cutting capacity and requires less effort than conventional end cutting nippers
■ cuts nails, small bolts and all wires including piano wire■ exceptional cutting capacity due to high leverage joint ■ cutting edge hardness approx. 64 HRC ■ Vanadium electric steel; forged, oil-hardened
Almost flush cutting of bolts, nails etc.High cutting performance: also for piano wire
Cutting capacitiesProduct Number inch
Pliers Head Handles
Ø inch Ø inch Ø inch Ø inch Ounces
61 01 200 8 85° black atramentized polished plastic coated 3/64 - 15/64 5/32 9/64 1/8 15.3
Cutting capacitiesProduct Number mm
Pliers Head Handles
Ø mm Ø mm Ø mm Ø mm Ounces
61 01 200 200 85° black atramentized polished plastic coated 1.0 - 6.0 4.0 3.5 3.0 15.3
■ with cutting edges for soft and medium hard wire
■ without bevel; for flush cutting ■ cutting edge hardness approx.
58 HRC ■ low-friction double spring for
gentle and even opening ■ precision box joint ■ the polish together with a fine
film of oil, offers effective rust protection – no circuit faults caused by peeling chrome from plated tools
■ Vanadium electric steel; forged, oil-hardened
Cutting capacities DimensionsProduct Number inch
Head Handles
Ø inch Ø inchA
inchB
inchC
inchD
inch Ounces
62 12 120 4 3/4 15° polished with multi-component grips 1/64 - 3/64 1/32 7/16 25/64 19/64 43/64 3.3
Cutting capacities DimensionsProduct Number mm
Head Handles
Ø mm Ø mmA
mmB
mmC
mmD
mm Ounces
62 12 120 120 15° polished with multi-component grips 0.3 - 1.0 0.7 11 10 7.5 17 3.3
63
64
cutting Pliers
64electronics end Cutting nippers ISO 9654
64 02 115
90°
64 12 115
90°
64 22 115
90°
64 32 120
15°
64 42 115
27° 64 22 115
64 62 120
64 72 120 64 02/11/12
64 52 115
27°
64 62 120
65°
64 72 120
35°
Pliers sets
see page 182
■ precision pliers for ultra fine cutting work, e.g. in electronics and fine mechanics
■ precision box joint ■ low-friction double spring for gentle and even opening ■ the polish or mirror polish (only finish 2), together with a fine film of
oil, offers effective rust protection – no circuit faults caused by peeling chrome from plated tools
■ cutting edge hardness at least 56 HRC ■ High-grade special tool steel; forged, oil-hardened
style 0End Cutter, with bevel
64 11 115End Cutter, without bevel
64 12 115End Cutter, with small bevel
style 2End Cutter, mini-blade with small bevel
style 3Oblique End Cutter, short head, with small bevel, α = 15°
style 4Oblique End Cutter, short head, with small bevel, α = 27°
style 5Oblique End Cutter, short head, without bevel, for flush cutting, α = 27°
style 6Oblique End Cutter, mini-blade with small bevel, α = 65°
style 7Oblique End Cutter, mini-blade withsmall bevel, head with recess, α = 35°
65
cutting Pliers
64 22 115 64 32/42/52 64 62 120 64 72 120
Cutting capacities DimensionsProduct Number inch
Style Head Handles
Ø inch Ø inch Ø inch
Ainch
Binch
Dinch
Cinch Ounces
64 02 115 4 1/2 90° 0 mirror polished with multi-component grips 5/64 3/64 1/64 7/16 15/64 19/64 5/8 3.3
64 11 115 4 1/2 90° 1 polished plastic coated 1/16 1/32 7/16 15/64 9/32 5/8 2.6
64 12 115 4 1/2 90° 1 mirror polished with multi-component grips 5/64 1/32 1/64 7/16 15/64 9/32 5/8 3.2
64 22 115 4 1/2 90° 2 mirror polished with multi-component grips 1/32 25/64 51/64 15/64 1/8 2.3
64 32 120 4 3/4 15° 3 mirror polished with multi-component grips 1/16 3/64 1/64 7/16 25/64 9/32 43/64 3.2
64 42 115 4 1/2 27° 4 mirror polished with multi-component grips 1/16 3/64 1/64 13/32 25/64 9/32 15/32 2.4
64 52 115 4 1/2 27° 5 mirror polished with multi-component grips 3/64 13/32 25/64 9/32 15/32 2.4
64 62 120 4 3/4 65° 6 mirror polished with multi-component grips 1/64 3/8 47/64 15/64 13/64 2.5
64 72 120 4 3/4 35° 7 mirror polished with multi-component grips 1/16 15/32 49/64 9/32 13/64 3.4
Cutting capacities DimensionsProduct Number mm
Style Head Handles
Ø mm Ø mm Ø mm
Amm
Bmm
Dmm
Cmm Ounces
64 02 115 115 90° 0 mirror polished with multi-component grips 2.0 1.0 0.6 11.0 6.0 7.5 16.0 3.3
64 11 115 115 90° 1 polished plastic coated 1.4 0.8 11.0 6.0 7.0 16.0 2.6
64 12 115 115 90° 1 mirror polished with multi-component grips 2.0 0.8 0.5 11.0 6.0 7.0 16.0 3.2
64 22 115 115 90° 2 mirror polished with multi-component grips 0.8 10.0 20.0 6.0 3.0 2.3
64 32 120 120 15° 3 mirror polished with multi-component grips 1.5 1.0 0.5 11.0 10.0 7.0 17.0 3.2
64 42 115 115 27° 4 mirror polished with multi-component grips 1.5 1.0 0.5 10.5 10.0 7.0 12.0 2.4
64 52 115 115 27° 5 mirror polished with multi-component grips 1.3 10.5 10.0 7.0 12.0 2.4
64 62 120 120 65° 6 mirror polished with multi-component grips 0.6 9.5 18.5 6.0 5.0 2.5
64 72 120 120 35° 7 mirror polished with multi-component grips 1.5 12.0 19.5 7.0 5.0 3.4
66
64electronics end-Cutting nippers esD ISO 9654
64 62 120 esD
65°
style 6Oblique End Cutter, mini-blade with small bevel, α = 65°
64 62 120 ESD
Pliers sets
see page 18264 62 120 ESD
cutting Pliers
esD pliers (electrostatic discharge)■ electrostatic energy is discharged through the handles in a
gradual and controlled manner■ protects components endangered by electrostatic discharge■ in accordance with applicable standards,
e.g. IEC TR 61 340-5, DIN EN 61 340-5, SP Method 2472
■ precision pliers for ultra fine cutting work, e.g. in electronics and fine mechanics
■ electrically discharging handles – energy dissipative ■ precision box joint ■ low-friction double spring for gentle and even opening ■ the mirror polish together with a fine film of oil, offers effective rust
protection – no circuit faults caused by peeling chrome from plated tools
■ cutting edge hardness approx. 56 HRC ■ with two-color dual component handles, black/grey ■ High-grade special tool steel; forged, oil-hardened
Cutting capacities Dimensions
Product Number inch
Style Head Handles
Ø inchA
inchB
inchD
inchC
inch Ounces
64 62 120 esD 4 3/4 65° 6 mirror polished with multi-component grips 1/64 3/8 47/64 15/64 13/64 2.5
Cutting capacities Dimensions
Product Number mm
Style Head Handles
Ø mmA
mmB
mmD
mmC
mm Ounces
64 62 120 esD 120 65° 6 mirror polished with multi-component grips 0.6 9.5 18.5 6.0 5.0 2.5
67
67high leverage end Cutting nippers ISO 5748
67 01 200
68end Cutting nippers ISO 5748
68 01 200
Also suitable for wire netting in reinforced concrete construction
69end Cutting nippers for mechanics
ISO 5748
69 01 130
cutting Pliers
■ with cutting edges for soft, hard and piano wire
■ high cutting capacity with little effort due to optimum coordination of cutting edge angle and transmission ratio
■ cutting edge hardness approx. 64 HRC
■ Chrome vanadium heavy-duty steel; forged, oil-hardened
Cutting capacitiesProduct Number inch mm
Pliers Head Handles
Ø inch Ø inch Ø inch Ø inch Ø mm Ø mm Ø mm Ø mm Ounces
67 01 140 5 1/2 140
black atramentized polished plastic coated
5/32 1/8 5/64 1/16 4.0 3.1 2.0 1.5 5.4
67 01 160 6 1/4 160 3/16 1/8 7/64 5/64 4.5 3.4 2.5 2.0 8.4
67 01 200 8 200 13/64 5/32 1/8 7/64 5.0 3.8 3.0 2.5 11.2
■ with cutting edges for soft and hard wire
■ also suitable for twisting and cutting binding wire
■ cutting edge hardness approx. 61 HRC
■ High-grade special tool steel; forged, oil-hardened
Cutting capacitiesProduct Number inch mm
Pliers Head Handles
Ø inch Ø inch Ø inch Ø mm Ø mm Ø mm Ounces68 01 160 6 1/4 160
black atramentized polished plastic coated
5/32 7/64 3/32 4.0 2.8 2.3 7.1
68 01 180 7 1/4 180 5/32 1/8 3/32 4.0 3.2 2.5 10.0
68 01 200 8 200 5/32 9/64 7/64 4.0 3.5 2.8 11.3
■ with cutting edges for soft, hard and piano wire; also suitable for thin copper wires
■ lap joint ■ cutting edge hardness
approx. 64 HRC ■ Chrome vanadium heavy duty
steel; forged, oil-hardened
Cutting capacities DimensionsProduct Number inch
Pliers Head Handles
Ø inch Ø inch Ø inch Ø inchA
inchB
inchD
inchC
inch Ounces
69 01 130 5 3/25 black atramentized polished plastic coated 1/64 - 5/64 3/64 3/64 1/32 5/8 19/64 25/64 51/64 3.9
Cutting capacities DimensionsProduct Number mm
Pliers Head Handles
Ø mm Ø mm Ø mm Ø mmA
mmB
mmD
mmC
mm Ounces
69 01 130 130 black atramentized polished plastic coated 0.4 - 2.0 1.3 1.0 0.8 16.0 7.5 10.0 20.0 3.9
68
The WoRlD oF KniPeX Diagonal CuTTeRs
33 Kg 39 Kg 52 Kg18 Kgwith
reapplication*
hand force requiredto cut a 1/8" nail
KniPeX TwinForce
The Dual action Cutter*
KniPeX X-Cut
* notch - reapply - cut through
NEwNEw
KniPeX Diagonal Cutter
KniPeX high leverage
Diagonal Cutter
Forged on hinged joint for robust usehand force is multiplied by 13
Long cutting edges for cutting cable; also precise enough for the finest stranded wires hand force is multiplied by 9
The Dual action Cutter
Double-hinged designhand force is multiplied by 39
Box joint: greatest stability with little weight hand force is multiplied by 16
KniPeX TwinForcehigh leverage Diagonal Cutter Diagonal CutterForce
NEw NEwKniPeX X-Cut
69
70Diagonal Cutters ISO 5749
70 01 160
70 02 160
■ the essential cutting tool for versatile use ■ high quality material and precise workmanship for long service life ■ precision cutting edges (cutting edge hardness approx. 62 HRC)
for soft and hard wire ■ clean cutting of thin copper wires, also at the cutting edge tips ■ narrow head style for use in confined areas ■ Vanadium electric steel; forged, oil-hardened
Cuts fine wires cleanly over the complete length of the blades
cutting Pliers
The slim head style and precise cutting capabilitiy are perfect for working in confined areas
Cutting capacitiesProduct Number inch mm
Pliers Head Handles
Ø inch Ø inch Ø inch Ø mm Ø mm Ø mm Ounces
70 01 110 4 1/4 110
black atramentized
polished plastic coated
1/8 5/64 3/64 3.0 2.0 1.2 2.8
70 01 125 5 125 1/8 3/32 1/16 3.0 2.3 1.5 2.8
70 01 140 5 1/2 140 5/32 3/32 5/64 4.0 2.5 1.8 4.4
70 01 160 6 1/4 160 5/32 7/64 5/64 4.0 2.8 2.0 6.0
70 01 180 7 1/4 180 5/32 1/8 3/32 4.0 3.0 2.5 7.1
70 02 125 5 125
black atramentized
polished with multi-component grips
1/8 3/32 1/16 3.0 2.3 1.5 4.2
70 02 140 5 1/2 140 5/32 3/32 5/64 4.0 2.5 1.8 5.3
70 02 160 6 1/4 160 5/32 7/64 5/64 4.0 2.8 2.0 7.3
70 02 180 7 1/4 180 5/32 1/8 3/32 4.0 3.0 2.5 8.9
70 08 160 sba 6 1/4 160
black atramentized
polishedinsulated with multi-component grips, VDE-tested
5/32 7/64 5/64 4.0 2.8 2.0 6.0
70 08 180 sba 7 1/4 180 5/32 1/8 3/32 4.0 3.0 2.5 7.1
70 08 160 sba
70
an all around tool for the toughest demands! 60% reduction in required force compared to conventional high leverage diagonal cutters. The ingenious lever action me-chanism ensures a favorable lever ratio with very little friction. The cutting force is about 20 times higher than the hand force applied.
71KniPeX Cobolt® Compact bolt Cutters
ISO 5743
71 01 200
71 02 200
71 12 200
71 22 20020°
71 41 20020°
opening spring and transport lock
The comparison 71 0x 200 with 71 2x 200 – the angled version provides a more flush cut
cutting Pliers
■ induction hardened edges cut hard, soft and piano wire■ cuts components like bolts, nails, rivets, etc. up to 1/8" dia. ■ exceptional cutting performance with minimal effort due to
innovative effective lever action design■ cutting edge hardness approx. 64 HRC ■ Chrome vanadium heavy-duty steel; forged, oil-hardened
71 12 200 / 71 22 200 / 71 32 200opening spring and locking lever are integrated into the handles for more comfortable work and safer transport
Form 220° angled head with single-sided lock plate and diagonal cutting edge for flush cutting; with space for gripping
Form 3the recess in the blade allows easier cutting of thicker wires, e.g. for anchor bolts in false ceilings
Form 4the recess in the blade allows easier cutting of thicker wires, e.g. for anchor bolts in false ceilings, 20° angled head with single-sided lock plate and diagonal cutting edge for flush cutting; with space for gripping
71 02 200 with slim, two-color multi-component sleeves for better handling and easier transport; with large contact surface on the handles for better allotment of pressure and more comfortable work
71 31/32/41 200: The cutting edge recess near the joint keeps thicker wires in a better cutting position (optimum lever ratio). There is no need to reposition the tool to achieve the desired cut.
Cutting capacitiesProduct Number
inch mm
Style Pliers Handles
Ø inch Ø inch Ø inch Ø inch Ø mm Ø mm Ø mm Ø mm Ounces
71 01 200 8 200 0 black atramentized plastic coated 1/4 13/64 5/32 9/64 6.0 5.2 4.0 3.6 11.8
71 01 200 R sba 8 200 0 black atramentized plastic coated 1/4 13/64 5/32 9/64 6.0 5.2 4.0 3.6 11.8
71 02 200 8 200 0 black atramentized with multi- component grips
1/4 13/64 5/32 9/64 6.0 5.2 4.0 3.6 12.9
71 12 200 8 200 1 black atramentizedwith multi- component grips
1/4 13/64 5/32 9/64 6.0 5.2 4.0 3.6 13.2
71 21 200 8 20020°
2 black atramentized plastic coated 1/4 13/64 5/32 9/64 6.0 5.2 4.0 3.6 11.3
71 22 200 8 200 20°
2 black atramentizedwith multi- component grips
1/4 13/64 5/32 9/64 6.0 5.2 4.0 3.6 13.2
71 31 200 8 200 3 black atramentized plastic coated 1/4 13/64 5/32 9/64 6.0 5.2 4.0 3.6 11.6
71 31 200 R sba 8 200 3 black atramentized plastic coated 1/4 13/64 5/32 9/64 6.0 5.2 4.0 3.6 11.6
71 32 200 8 200 3 black atramentizedwith multi- component grips
1/4 13/64 5/32 9/64 6.0 5.2 4.0 3.6 13.1
71 41 200 8 20020°
4 black atramentized plastic coated 1/4 13/64 5/32 9/64 6.0 5.2 4.0 3.6 11.8
71
cutting Pliers
DegRee oF FoRCe ReQuiReD70 % 100 %
Conventional bolt Cutter:
max. opening is approx. 1/8" in diameterweight = 21 ouncesdouble joint
KniPeX-model e.g. 71 31 200 Cobolt®:
weight = 11 ouncesgood gripsmall size requires 30% less power than conventional bolt cutters
21 oz.
11 oz.
joint axle
hard wire Ø 5/64"
picture not true to scale
72
cutting Pliers
7172 bolt Cutters
for hard materials up to 48 hRC
71 72 460
71 72 610
71 72 760
71 72 910
Forged-on stopper with absorbing inserts: cushions the cutting stroke
■ cutting capacity up to 48 HRC hardness ■ robust cutting edges with a hardness of approx. 62 HRC ■ forged-on stopper with comfortable shock absorber ■ good access due to very flat construction of head and joint area ■ ergonomically angled handles to minimize effort ■ sturdy, two-color dual component handles won't slip ■ precise adjustment (12 positions) by cam bolt■ high cutting performance with minimum effort due to optimum
coordination of the cutting edge angle, transmission ratio and ergonomic handle shape
■ bolted cutter head, replaceable ■ blade: Chrome vanadium heavy-duty steel; forged, oil-hardened■ joint: Special tool steel; forged ■ handle: steel tube, powder-coated
Cutting capacitiesProduct Number inch mm
Head Handles HRC 19Ø inch
HRC 40Ø inch
HRC 48Ø inch
HRC 19Ø mm
HRC 40Ø mm
HRC 48Ø mm Ounces
71 72 460 18 1/4 460 grey atramentized with multi-component grips 5/16 1/4 13/64 8.0 6.0 5.0 74.1
71 72 610 24 610 grey atramentized with multi-component grips 23/64 5/16 9/32 9.0 8.0 7.0 90.0
71 72 760 30 760 grey atramentized with multi-component grips 7/16 23/64 5/16 11.0 9.0 8.0 150.0
71 72 910 35 3/4 910 grey atramentized with multi-component grips 1/2 25/64 23/64 13.0 10.0 9.0 175.0
73
cutting Pliers
7182 Concrete mesh Cutter
71 82 950
The special shape of the mesh cutter head enables it to cut structural steel that is lying down flat
■ cutting capacity up to 48 HRC hardness ■ robust cutting edges with a hardness of approx. 62 HRC ■ forged-on stopper with comfortable shock absorber ■ good access due to very flat construction of head and joint area ■ ergonomically angled handles to minimize effort ■ sturdy, two-color dual component handles won't slip ■ precise adjustment (12 positions) by cam bolt ■ high cutting performance with minimum effort due to optimum
coordination of the cutting edge angle, transmission ratio and ergonomic handle shape
■ bolted cutter head; replaceable ■ blade: Chrome vanadium heavy-duty steel; forged, oil-hardened■ joint: Special tool steel; forged ■ handle: steel tube, powder-coated
Cutting capacitiesProduct Number inch mm
Head Handles HRC 19Ø inch
HRC 40Ø inch
HRC 48Ø inch
HRC 19Ø mm
HRC 40Ø mm
HRC 48Ø mm Ounces
71 82 950 37 1/2 950 grey atramentized with multi-component grips 7/16 23/64 1/4 11.0 9.0 6.0 130.0
74
The KEVLAR® fibers in strain relief are cut with the 95 03 160 shears. KEVLAR® is a registered trademark of E. I. du Pont de Nemours and Company
cutting Pliers
72
72 01 160
72 11 16045°
72 21 16085°
Diagonal Cutters for plastics ISO 5743
■ provides a fully flush cut when cutting tie-wraps, plastic and soft metals■ with opening spring ■ Vanadium electric steel; forged, oil-hardened
Product Number inch mm
Head Handles
Ounces
72 01 140 5 1/2 140
polished plastic coated
4.4
72 01 160 6 1/4 160 5.8
72 01 180 7 1/4 180 6.8
72 11 160 6 1/4 160 45° polished plastic coated 5.5
72 21 160 6 1/4 160 85° polished plastic coated 5.8
7251 Diagonal Cutter for fiber optics
(glass fiber cable)
DIN ISO 5743
72 51 160
■ specially developed for flush cutting of fiber optics (glass fiber cables) ■ cutting edges additionally induction hardened ■ with opening spring ■ Vanadium electric steel; forged, oil-hardened
Product Number inch mm
Head Handles
Ounces
72 51 160 6 1/4 160 polished plastic coated 5.9
75
Cuts fine strands as well as multi-core cables and piano wire.
73KniPeX X-Cut Compact and light. Powerful and precise.
73 02 160
■ box-joint design: highest stability at low weight ■ double supported joint axis for heavy duty cutting■ high cutting capacity with very little effort due to the optimum
coordination of the cutting edge angle and lever ratio with off center pivot point
■ 40% less effort required compared to diagonal cutters of the same length
■ large opening width for thicker cables■ cuts all wires precisely, even fine copper wires■ compact, low-weight construction■ universally usable in assembly, maintenance and production■ Chrome vanadium heavy duty steel; forged, oil-hardened
73 05 160
73 06 160
Product Number mm
Pliers Head Handles
Ø mm Ø mm Ø mm Ø mm
Ø mm Ounces
73 02 160 160 black atramentized
polished with multi-component grips 4.8 3.8 2.7 2.2 12.0 6.2
73 05 160 160 chrome plated with multi-component grips 4.8 3.8 2.7 2.2 12.0 6.2
73 06 160 160 chrome plated insulated with multi-component grips, VDE-tested
4.8 3.8 2.7 2.2 12.0 6.9
Product Number inch
Pliers Head Handles
Ø inch Ø inch Ø inch Ø inch
Ø inch Ounces
73 02 160 6 1/4black atramentized
polished with multi-component grips 3/16 5/32 7/64 3/32 15/32 6.2
73 05 160 6 1/4 chrome plated with multi-component grips 3/16 5/32 7/64 3/32 15/32 6.2
73 06 160 6 1/4 chrome plated insulated with multi-component grips, VDE-tested
3/16 5/32 7/64 3/32 15/32 6.9
cutting Pliers
76
20% reduction in required forcecompared to conventional diagonal cutters of the same length. With forged-on joint axle.
cutting Pliers
74high leverage Diagonal Cutters ISO 5749
74 01 200
74 02 250
74 12 180
74 21 20012°
style 1with opening spring; to be activated if required
74 12: Opening spring in deactivated position
74 12: Just pressing with your thumb will activate the opening spring
style 212° angled head offers ample space for gripping
■ for very tough, continuous use ■ high cutting performance with minimum effort due to optimum
coordination of the cutting edge angle, transmission ratio and ergonomic handle shape
■ precision cutting edges (cutting edge hardness approx. 64 HRC) cut several types of wire including piano wire
■ Chrome vanadium heavy duty steel; forged, oil-hardened
With forged-on axle for heaviest duty
74 08 200 sba
74 08 250 sba
77
cutting Pliers
hard wire (Ø 5/64")
80 % 100 %
joint axle
20% reduction in required hand force
Cutting capacitiesProduct Number inch mm
Style Pliers Head Handles
Ø inch Ø inch Ø inch Ø mm Ø mm Ø mm Ounces
74 01 140 5 1/2 140
0black atramentized
polished plastic coated
1/8 5/64 1/16 3.1 2.0 1.5 4.6
74 01 160 6 1/4 160 1/8 3/32 5/64 3.4 2.5 2.0 6.3
74 01 180 7 1/4 180 5/32 7/64 3/32 3.8 2.7 2.2 8.5
74 01 200 8 200 11/64 1/8 3/32 4.2 3.0 2.5 9.3
74 01 250 10 250 3/16 9/64 1/8 4.6 3.5 3.0 13.8
74 02 140 5 1/2 140
0 black atramentized
polished with multi-component grips
1/8 5/64 1/16 3.1 2.0 1.5 5.5
74 02 160 6 1/4 160 1/8 3/32 5/64 3.4 2.5 2.0 7.4
74 02 180 7 1/4 180 5/32 7/64 3/32 3.8 2.7 2.2 9.6
74 02 200 8 200 11/64 1/8 3/32 4.2 3.0 2.5 10.7
74 02 250 10 250 3/16 9/64 1/8 4.6 3.5 3.0 15.4
74 08 200 8 200
0
black atramentized
polishedinsulated with multi- component grips, VDE-tested
11/64 1/8 3/32 4.2 3.0 2.5 10.7
74 08 250 10 250 3/16 9/64 1/8 4.6 3.5 3.0 15.4
74 12 160 6 1/4 160 1
black atramentized
polished with multi-component grips 1/8 3/32 5/64 3.4 2.5 2.0 7.4
74 12 180 7 1/4 180 5/32 7/64 3/32 3.8 2.7 2.2 9.6
74 21 160 6 1/4 160
12° 2black atramentized
polished plastic coated
1/8 3/32 5/64 3.4 2.5 2.0 6.4
74 21 180 7 1/4 180 5/32 7/64 3/32 3.8 2.7 2.2 8.3
74 21 200 8 200 11/64 1/8 3/32 4.2 3.0 2.5 9.1
74 21 250 10 250 3/16 9/64 1/8 4.6 3.5 3.0 13.8
74 22 200 8 20012° 2
black atramentized
polished with multi-component grips 11/64 1/8 3/32 4.2 3.0 2.5 10.6
74 22 250 10 250 3/16 9/64 1/8 4.6 3.5 3.0 15.4
leverage comparison between the Diagonal Cutter <=> high leverage Diagonal Cutter
hanD FoRCe ReQuiReD
high power transmission Power cutter:hand force of 290 N required to cut hard wire (Ø 5/64")
normal power transmission Cutter:hand force of 370 N required to cut hard wire (Ø 5/64")
20% reduction thanks to high leverage power joint
78
Twin
Forc
eTw
inFo
rce
79
737 KniPeX TwinForce
high leverage Diagonal Cutter
73 72 180
■ ideal transmission of force due to double-hinged design■ extremely easy cutting with little strain■ cuts again 50% easier than the tried and tested high leverage diagonal cutters■ reliably cuts all types of wire, including steel tape■ NEW for diagonal cutters: The option to reapply the tool. The KNIPEX TwinForce cuts even 5/32" thick
wire without great effort when reapplied two or three times. Conventional high leverage diagonal cutters either cannot cut these diameters or only with very great effort.
■ for rough or very fine cutting■ low cutting impact: gentle on hands. The tension on muscles and tendons is relieved■ cuts wire up to Ø 5/32" without considerable effort when reapplied several times■ high degree of stability and zero-backlash due to precisely milled forged-in axle■ Chrome vanadium heavy duty steel
Cutting capacitiesProduct Number inch
Pliers Head Handles
Ø inch Ø inch Ø inch Ø inch Ounces
73 71 180 7 1/4 black atramentized polished plastic coated 7/32 3/16 1/8 1/8 9.0
73 72 180 7 1/4 black atramentized polishedwith multi- component grips
7/32 3/16 1/8 1/8 9.0
7491
high leverage Center Cutters ISO 5743
74 91 250
■ with forged-on axle for heavy duty cutting ■ with precision cutting edges for soft, hard and piano wire ■ cuts thick wires with less effort than other diagonal cutters of
the same length ■ cutting edges are in the center of the cutter head ■ high cutting performance with minimal effort due to optimum
coordination of the cutting edge angle, transmission ratio and ergonomic handle shape
■ cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC
■ Chrome vanadium heavy-duty steel; forged, oil-hardened
Cutting capacitiesProduct Number inch
Pliers Head Handles
Ø inch Ø inch Ø inch Ø inch Ounces
74 91 250 10 black atramentized polished plastic coated 13/64 13/64 5/32 9/64 14.0
Cutting capacitiesProduct Number mm
Pliers Head Handles
Ø mm Ø mm Ø mm Ø mm Ounces
74 91 250 250 black atramentized polished plastic coated 5.0 5.0 3.8 3.5 14.0
meet the TwinForce The ideal tool for cutting thicker wires. New to the Diagonal Cutter family is the option to reapply the tool. This is due to the innovative double-hinged design. Each cutting repetition reduces the effort required to achieve the ultimate cut. Reapplying with the KNIPEX TwinForce allows the user to cut materials that cannot be cut with comparable diagonal cutters of the same length.
Cutting capacitiesProduct Number mm
Pliers Head Handles
Ø mm Ø mm Ø mm Ø mm Ounces
73 71 180 180 black atramentized polished plastic coated 5.5 4.6 3.2 3.0 9.0
73 72 180 180 black atramentized polishedwith multi- component grips
5.5 4.6 3.2 3.0 9.0
The cutting edges are in the center of the cutter head
cutting Pliers
80
cutting Pliers
75electronics Diagonal Cutters ISO 9654
75 02 125
75 12 125
75 22 125
75 52 125
style 0with bevel
style 1with bevel and wire clamp, no uncontrolled loss of cut wire ends
style 2with small bevel
style 5particularly narrow head, with bevel Bolted joint
■ bolted joint for high precision and stress tolerance ■ for very precise assembly work, e.g. in electronics and fine mechanics ■ with sharp, ground cutting for soft and hard wire and piano wire ■ cutting edge hardness approx. 64 HRC ■ low-friction double spring for gentle and even opening ■ High-grade special tool steel; forged, oil-hardened
Cutting capacities DimensionsProduct Number inch
Style Pliers Handles
Ø inch Ø inch Ø inch Ø inchA
inchB
inchD
inch Ounces
75 02 125 5 0 burnished plastic coated 1/64 - 3/64 3/64 1/64 1/64 13/32 35/64 17/64 2.9
75 12 125 5 1 burnished plastic coated 1/64 - 3/64 3/64 1/64 1/64 13/32 35/64 17/64 2.8
75 22 125 5 2 burnished plastic coated 1/64 - 3/64 2/64 1/64 1/64 13/32 35/64 17/64 2.8
75 52 125 5 5 burnished plastic coated 1/64 - 3/64 1/64 1/64 13/32 35/64 17/64 2.8
Cutting capacities DimensionsProduct Number mm
Style Pliers Handles
Ø mm Ø mm Ø mm Ø mmA
mmB
mmD
mm Ounces
75 02 125 125 0 burnished plastic coated 0.2 - 1.3 1.0 0.6 0.4 10.5 14 6.5 2.9
75 12 125 125 1 burnished plastic coated 0.2 - 1.3 1.0 0.6 0.4 10.5 14 6.5 2.8
75 22 125 125 2 burnished plastic coated 0.2 - 1.3 0.9 0.4 0.3 10.5 14 6.5 2.8
75 52 125 125 5 burnished plastic coated 0.2 - 0.8 0.5 0.3 10.5 14 6.5 2.8
81
76Diagonal Cutters for electromechanics
ISO 5749
76 01 125
■ with sharp, precisely aligned cutting edges for soft, hard and piano wire
■ cutting edge hardness approx. 63 HRC ■ lap joint ■ Vanadium electric steel; forged, oil-hardened
style 1low-friction double spring for gentle and even opening
style 2without bevel for flush cutting of soft wires; low-friction double spring for gentle and even opening
style 8tapered head with small bevel for work in confined areas (cable harnesses, multiple stranded wires)
Cutting capacities DimensionsProduct Number inch
Pliers Head Handles
Ø inch Ø inch Ø inch Ø inchA
inchB
inchD
inch Ounces
76 01 125 5 black atramentized polished plastic coated 1/64 - 1/8 3/32 1/16 1/64 37/64 5/8 23/64 3.2
76 22 125 5 black atramentized polishedwith multi- component grips
1/64 - 7/64 37/64 5/8 23/64 3.8
76 81 125 5 black atramentized polished plastic coated 1/64 - 5/64 3/64 1/32 37/64 5/8 23/64 3.1
Cutting capacities DimensionsProduct Number mm
Pliers Head Handles
Ø mm Ø mm Ø mm Ø mmA
mmB
mmD
mm Ounces
76 01 125 125 black atramentized polished plastic coated 0.4 - 3.0 2.3 1.5 0.6 14.5 16.0 9.0 3.2
76 22 125 125 black atramentized polishedwith multi- component grips
0.4 - 2.5 14.5 16.0 9.0 3.8
76 81 125 125 black atramentized polished plastic coated 0.4 - 1.7 1.3 0.8 14.5 16.0 9.0 3.1
cutting Pliers
82
cutting Pliers
77electronics Diagonal Cutters ISO 9654
77 01 115
77 02 115
77 12 115
77 22 115
77 01 115 round head, with bevel
77 02 115round head, with small bevel
77 11 115round head, with bevel and lead catcher – no uncontrolled loss of cut wire ends
77 21 115pointed head, without bevel
77 22 115round head, without bevel; cutting edge hardness approx. 57 HRC
77 32 115pointed head, with small bevel
77 42 115pointed head, without bevel; cutting edge hardness approx. 57 HRC
77 52 115pointed, flat head, with small bevel; cutting edge hardness approx. 57 HRC
77 72 115miniature head with small bevel
77 42 115
77 52 115
77 72 115
■ for fine cutting work, e.g. in electronics and fine mechanics ■ sturdy, zero-backlash box joint ■ low-friction double spring for gentle and even opening ■ the polish or mirror polish (only finish 2) together with a fine
film of oil, offers effective rust protection – no circuit faults caused by peeling chrome from plated tools
■ cutting edge hardness approx. 62 HRC ■ High-grade special tool steel; forged, oil-hardened
83
Cutting capacities DimensionsProduct Number inch
Head Handles
Ø inch Ø inch Ø inchB
inchA
inchD
inch Ounces
77 01 115 4 1/2 polished plastic coated
1/64 - 1/16 3/64 1/64 35/64 7/16 19/64 2.4
77 01 130 5 1/4 1/64 - 5/64 1/16 1/32 23/32 19/32 3/8 3.8
77 02 115 4 1/2 mirror polished with multi-component grips 1/64 - 1/16 3/64 1/64 35/64 7/16 19/64 2.8
77 12 115 4 1/2 mirror polished with multi-component grips 1/64 - 1/16 3/64 1/64 35/64 7/16 19/64 2.8
77 22 115 4 1/2 mirror polished with multi-component grips 1/64 - 3/64 3/64 35/64 7/16 9/32 2.8
77 22 130 5 1/4 mirror polished with multi-component grips 1/64 - 5/64 1/16 23/32 19/32 23/64 4.4
77 42 115 4 1/2 mirror polished with multi-component grips
1/64 - 3/64 1/32 35/64 7/16 19/64 2.8
77 42 130 5 1/4 1/64 - 1/16 3/64 23/32 19/32 3/8 4.3
77 52 115 4 1/2 mirror polished with multi-component grips 1/64 - 3/64 1/32 1/64 35/64 7/16 19/64 2.7
77 72 115 4 1/2 mirror polished with multi-component grips 1/64 - 1/32 13/32 3/8 15/64 2.4
Cutting capacities DimensionsProduct Number mm
Head Handles
Ø mm Ø mm Ø mmB
mmA
mmD
mm Ounces
77 01 115 115 polished plastic coated
0.3 - 1.6 1.2 0.6 14.0 11.0 7.5 2.4
77 01 130 130 0.3 - 2.0 1.5 0.8 18.0 15.0 9.5 3.8
77 02 115 115 mirror polished with multi-component grips 0.3 - 1.6 1.2 0.6 14.0 11.0 7.5 2.8
77 12 115 115 mirror polished with multi-component grips 0.3 - 1.6 1.2 0.6 14.0 11.0 7.5 2.8
77 22 115 115 mirror polished with multi-component grips 0.3 - 1.3 1.0 14.0 11.0 7.0 2.8
77 22 130 130 mirror polished with multi-component grips 0.3 - 2.0 1.5 18.0 15.0 9.0 4.4
77 42 115 115 mirror polished with multi-component grips
0.3 - 1.3 0.8 14.0 11.0 7.5 2.8
77 42 130 130 0.3 - 1.6 1.3 18.0 15.0 9.5 4.3
77 52 115 115 mirror polished with multi-component grips 0.3 - 1.0 0.8 0.5 14.0 11.0 7.5 2.7
77 72 115 115 mirror polished with multi-component grips 0.3 - 0.8 10.5 9.5 6.0 2.4
cutting Pliers
Pliers sets
see page 182
84
esD pliers (electrostatic discharge)■ electrostatic energy is discharged through the handles in a
gradual and controlled manner■ protects components endangered by electrostatic discharge■ in accordance with applicable standards,
e.g. IEC TR 61 340-5, DIN EN 61 340-5, SP Method 2472
cutting Pliers
77electronics Diagonal Cutters esD ISO 9654
77 02 115 esD
77 22 115 esD
77 42 115 esD
77 02 115 esDround head, with small bevel
77 22 115 esDround head, without bevel
77 42 115 esDpointed head, without bevel
■ for very precise assembly work, e.g. in electronics and fine mechanics ■ electrically discharging handles – dissipative ■ sturdy, zero-backlash box joint ■ low-friction double spring for gentle and even opening ■ the mirror polish together with a fine film of oil, offers effective
rust protection – no circuit faults caused by peeling chrome from plated tools
■ cutting edge hardness approx. 62 HRC ■ with two-color dual component handles, black/grey ■ High-grade special tool steel; forged, oil-hardened
Cutting capacities DimensionsProduct Number inch
Head Handles
Ø inch Ø inch Ø inch
Binch
Ainch
Dinch Ounces
77 02 115 esD 4 1/2 mirror polished with multi-component grips 1/64 - 1/16 3/64 1/64 35/64 7/16 19/64 2.9
77 22 115 esD 4 1/2 mirror polished with multi-component grips 1/64 - 3/64 3/64 35/64 7/16 19/64 2.8
77 42 115 esD 4 1/2 mirror polished with multi-component grips 1/64 - 3/64 1/32 35/64 7/16 19/64 2.8
Cutting capacities DimensionsProduct Number mm
Head Handles
Ø mm Ø mm Ø mm
Bmm
Amm
Dmm Ounces
77 02 115 esD 115 mirror polished with multi-component grips 0.3 - 1.6 1.2 0.6 14.0 11.0 7.5 2.9
77 22 115 esD 115 mirror polished with multi-component grips 0.3 - 1.3 1.0 14.0 11.0 7.5 2.8
77 42 115 esD 115 mirror polished with multi-component grips 0.3 - 1.3 0.8 14.0 11.0 7.0 2.8
Pliers sets
see page 182
85
86
Optimum cutting edge geometry: precise, easy cutting even with strands on top
Restricted opening for ergonomic handle holding
Grooves for a steady grip when applying slight pressure
78 61 125
78 71 125
78electronic Super Knips® ISO 9654
78 03 125
78 23 125
60°
78 31 125
78 41 125
cutting Pliers
■ precision pliers for ultra fine cutting work, e.g. in electronics and fine mechanics
■ ground, very sharp cutting edges without bevel for flush cutting ■ precision shaped tips cut through close wires from 1/64" dia. ■ stainless steel rivet ■ cutting edges additionally induction hardened ■ extremely smooth movement for minimum operator fatigue ■ with opening spring ■ INOX or Special tool steel
78 03 125 / 78 23 125INOX-stainless steel; cutting edge hardness approx. 54 HRC
78 31 125Cutting edges additionally induction hardened, cutting edge hardness approx. 60 HRC; with narrow head; Special tool steel, burnished
78 41 125Cutting edges additionally induction hardened, cutting edge hardness approx. 60 HRC; with narrow head; with lead catcher – no uncontrolled loss of cut wire ends; Special tool steel, burnished
78 61 125Cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC; also suitable for cutting glass fiber cables (fiber optics)
78 71 125Special tool steel, burnished; with lead catcher – no uncontrolled loss of cut wire ends; cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC
87
cutting Pliers
Cutting capacities DimensionsProduct Number inch
Pliers Head Handles
Ø inch Ø inch Ø inchB
inchA
inchD
inch Ounces
78 03 125 5 polished with multi-component grips 1/64 - 1/16 3/64 23/64 17/32 19/64 2.0
78 23 125 5 60° polished with multi-component grips 1/64 - 3/64 1/64 7/32 17/32 19/64 1.9
78 31 125 5 burnished with multi-component grips 1/64 - 3/64 23/64 1/2 19/64 1.9
78 41 125 5 burnished with multi-component grips 1/64 - 3/64 23/64 1/2 19/64 2.0
78 61 125 5 burnished with multi-component grips 1/64 - 1/16 3/64 1/64 23/64 17/32 19/64 2.0
78 71 125 5 burnished with multi-component grips 1/64 - 1/16 3/64 1/64 23/64 17/32 19/64 2.0
Cutting capacities DimensionsProduct Number mm
Pliers Head Handles
Ø mm Ø mm Ø mmB
mmA
mmD
mm Ounces
78 03 125 125 polished with multi-component grips 0.2 - 1.6 1.0 9.0 13.5 7.5 2.0
78 23 125 125 60° polished with multi-component grips 0.2 - 1.0 0.6 5.5 13.5 7.5 1.9
78 31 125 125 burnished with multi-component grips 0.2 - 1.0 9.0 12.5 7.5 1.9
78 41 125 125 burnished with multi-component grips 0.2 - 1.0 9.0 12.5 7.5 2.0
78 61 125 125 burnished with multi-component grips 0.2 - 1.6 1.2 0.6 9.0 13.5 7.5 2.0
78 71 125 125 burnished with multi-component grips 0.2 - 1.6 1.2 0.6 9.0 13.5 7.5 2.0
esD pliers (electrostatic discharge)■ electrostatic energy is discharged through the handles in a
gradual and controlled manner■ protects components endangered by electrostatic discharge■ in accordance with applicable standards,
e.g. IEC TR 61 340-5, DIN EN 61 340-5, SP Method 2472
78electronic Super Knips® esD ISO 9654
78 03 125 esD
■ precision pliers for ultra fine cutting work, e.g. in electronics
and fine mechanics ■ electrically discharging handles – dissipative ■ ground, very sharp cutting edges without bevel for flush cutting ■ precision shaped tips cut through close wires from 1/64" dia. ■ stainless steel rivet ■ extremely smooth movement
for minimal operator fatigue ■ with opening spring
78 03 125 esDSurgeon steel; cutting edge hardness approx. 54 HRC
Cutting capacities DimensionsProduct Number inch
Head Handles
Ø inch Ø inchB
inchA
inchD
inch Ounces
78 03 125 esD 5 polished with multi-component grips 1/64 - 1/16 3/64 23/64 17/32 19/64 1.9
Cutting capacities DimensionsProduct Number mm
Head Handles
Ø mm Ø mmB
mmA
mmD
mm Ounces
78 03 125 esD 125 polished with multi-component grips 0.2 - 1.6 1.0 9.0 13.5 7.5 1.9
88
small Change. big Difference.KNIPEX Precision Electronics Pliers are made of high-quality ball bearing steel and processed with the highest degree of care. Each opening movement is gentle and without backlash. Each work step proceeds reliably and precisely.
cutting Pliers
79Precision electronics Diagonal Cutters ISO 9654
79 02 120
79 02 125
79 22 120
79 22 125
79 32 125
79 42 125
Cutting edges without bevel Cutting edges with very small bevel
■ precision pliers for ultra fine cutting work, e.g. in electronics and fine mechanics
■ very precisely ground and sharp cutting edges wih small bevels for precise cutting work on small electronic components
■ a version without the bevel is available for flush cutting■ cutting edges additionally induction hardened, cutting edge
hardness approx. 64 HRC ■ approx. 20% lighter than conventional electronics pliers ■ bolted joint with carefully manufactured joint surfaces for even,
low-friction movement throughout the entire opening range■ smooth-running double spring for a gentle and even opening ■ ergonomically optimized handle covers ■ Chrome vanadium ball-bearing steel; forged
79 02 120 / 79 22 120mini-head
79 02 125 / 79 22 125round head
79 12 125for cutting through hard wire and piano wire
79 32 125 / 79 42 125pointed head
89
Cutting capacities DimensionsProduct Number mm
Pliers Head HandlesØ mm Ø mm Ø mm Ø mm
Bmm
Amm
Dmm Ounces
79 02 120 120 burnished polished with multi-component grips 0.2 - 1.4 1.0 0.6 6.5 9.0 6.5 2.0
79 02 125 125 burnished polished with multi-component grips 0.2 - 1.7 1.3 0.7 10.0 11.0 6.5 2.1
79 12 125 125 burnished polished with multi-component grips 0.3 - 1.7 1.3 1.0 0.6 10.0 11.0 6.5 2.1
79 22 120 120 burnished polished with multi-component grips 0.1 - 1.3 0.8 6.5 9.0 6.5 2.0
79 22 125 125 burnished polished with multi-component grips 0.1 - 1.7 1.0 10.0 11.0 6.5 2.1
79 32 125 125 burnished polished with multi-component grips 0.2 - 1.5 1.1 0.6 11.0 11.0 6.5 2.0
79 42 125 125 burnished polished with multi-component grips 0.1 - 1.5 0.8 11.0 11.0 6.5 2.0
Cutting capacities DimensionsProduct Number inch
Pliers Head HandlesØ inch Ø inch Ø inch Ø inch
Binch
Ainch
Dinch Ounces
79 02 120 4 3/4 burnished polished with multi-component grips 1/64 - 1/16 3/64 1/64 17/64 23/64 17/64 2.0
79 02 125 5 burnished polished with multi-component grips 1/64 - 5/64 3/64 1/32 25/64 7/16 17/64 2.1
79 12 125 5 burnished polished with multi-component grips 1/64 - 5/64 3/64 3/64 1/64 25/64 7/16 17/64 2.1
79 22 120 4 3/4 burnished polished with multi-component grips 1/64 - 3/64 1/32 17/64 23/64 17/64 2.0
79 22 125 5 burnished polished with multi-component grips 1/64 - 5/64 3/64 25/64 7/16 17/64 2.1
79 32 125 5 burnished polished with multi-component grips 1/64 - 1/16 3/64 1/64 7/16 7/16 17/64 2.0
79 42 125 5 burnished polished with multi-component grips 1/64 - 1/16 1/32 7/16 7/16 17/64 2.0
cutting Pliers
90
cutting Pliers
79Precision electronics Diagonal Cutters esD ISO 9654
79 02 120 esD
79 02 125 esD
79 22 120 esD
79 22 125 esD
79 42 125 esD
79 32 125 esD
esD pliers (electrostatic discharge)■ electrostatic energy is discharged through the handles
in a gradual and controlled manner■ protects components endangered by electrostatic discharge■ in accordance with applicable standards,
e.g. IEC TR 61 340-5, DIN EN 61 340-5, SP Method 2472
■ precision pliers for ultra fine cutting work, e.g. in electronics and fine mechanics
■ very precisely ground and sharp cutting edges wih small bevels for precise cutting work on small electronic components
■ a version without the bevel is available for flush cutting■ electrically discharging handles – dissipative ■ cutting edge hardness approx. 64 HRC ■ approx. 20% lighter than conventional electronics pliers ■ bolted joint with particularly carefully manufactured joint surfaces for
even, low-friction movement throughout the entire opening range■ smooth-running double spring for a gentle and even opening ■ ergonomically optimized handle covers ■ Chrome vanadium ball-bearing steel; forged
79 02 120 esD / 79 22 120 esDmini-head
79 02 125 esD / 79 22 125 esDround head
79 12 125 esDfor cutting through hard wire and piano wire
79 32 125 esD / 79 42 125 esDpointed head
91
Cutting capacities DimensionsProduct Number inch
Pliers Head Handles
Ø inch Ø inch Ø inch Ø inchB
inchA
inchD
inch Ounces
79 02 120 esD 4 3/4
burnished polished with multi-component grips 1/64 - 1/16 3/64 1/64 17/64 23/64 17/64 2.1
79 02 125 esD 5
burnished polished with multi-component grips 1/64 - 5/64 3/64 1/32 25/64 7/16 17/64 2.2
79 12 125 esD 5
burnished polished with multi-component grips 1/64 - 5/64 3/64 3/64 1/64 25/64 7/16 17/64 2.2
79 22 120 esD 4 3/4
burnished polished with multi-component grips 1/64 - 3/64 1/32 17/64 23/64 17/64 2.2
79 22 125 esD 5
burnished polished with multi-component grips 1/64 - 5/64 3/64 25/64 7/16 17/64 2.2
79 32 125 esD 5
burnished polished with multi-component grips 1/64 - 1/16 3/64 1/64 13/32 7/16 17/64 2.2
79 42 125 esD 5
burnished polished with multi-component grips 1/64 - 1/16 1/32 13/32 7/16 17/64 2.0
Cutting capacities DimensionsProduct Number mm
Pliers Head Handles
Ø mm Ø mm Ø mm Ø mmB
mmA
mmD
mm Ounces
79 02 120 esD 120
burnished polished with multi-component grips 0.2 - 1.4 1.0 0.6 6.5 9.0 6.5 2.1
79 02 125 esD 125
burnished polished with multi-component grips 0.2 -1.7 1.3 0.7 10.0 11.0 6.5 2.2
79 12 125 esD 125
burnished polished with multi-component grips 0.3 - 1.7 1.3 1.0 0.6 10.0 11.0 6.5 2.2
79 22 120 esD 120
burnished polished with multi-component grips 0.1 - 1.3 0.8 6.5 9.0 6.5 2.2
79 22 125 esD 125
burnished polished with multi-component grips 0.1 - 1.7 1.0 10.0 11.0 6.5 2.2
79 32 125 esD 125
burnished polished with multi-component grips 0.2 - 1.5 1.1 0.6 10.5 11.0 6.5 2.2
79 42 125 esD 125
burnished polished with multi-component grips 0.1 - 1.5 0.8 10.5 11.0 6.5 2.0
cutting Pliers
92
93
PiPe wrencHes And wAter PumP Pliers
81Pipe gripping Pliers
for plastic pipes and connectors
DIN ISO 5743
81 03 230
81 13 230
■ ideal for tightening and releasing plastic pipe joints, round union nuts, etc. from 1“- 2 9/16“ dia.
■ serrated or smooth jaws ■ 4-position adjustable slip joint ■ Chrome vanadium electric steel; forged, oil-hardened
Working capacityProduct Number inch mm
Pliers Handles Ø inch Ø mm
Ounces
81 03 230 9 1/4 230 chrome plated plastic coated 1 - 2 9/16 25 - 65 10.4
81 13 230 9 1/4 230 chrome plated plastic coated 1 - 2 23/64 25 - 60 10.2
81 19 230 2 pairs of plastic jaws for 81 13 230
84Cycle Pliers DIN ISO 5743
84 11 200
■ for very narrow screw connections ■ Special tool steel; forged, oil-hardened
84 11 200straight head
84 21 20020° angled head
Recess Head thicknessProduct Number inch mm
Pliers Head Handles Ø inch Ø mm inch mm
Ounces
84 11 200 8 200 black atramentized polished plastic coated 1/4 / 3/8 6 / 10 1/8 3.5 6.2
84 21 200 8 200 20° black atramentized polished plastic coated 1/4 / 3/8 6 / 10 1/8 3.5 6.4
81 13 230with plastic jaws for careful installation up to 2 23/64“ dia.
94
PiPe wrencHes And wAter PumP Pliers
831 Pipe Wrenches 90°
DIN 5234
83 10 01590°
■ Swedish pattern ■ 90° angled jaws ■ jaws with offset teeth in
opposite directions ■ teeth additionally induction
hardened ■ I-beam handle design ■ captive adjusting nut ■ red powder-coated,
jaws bright ground
■ Chrome vanadium electric steel; forged, oil-hardened
Clamping widthProduct Number inch mm
Pliers
Ø inch inch Ø mm
inch mm
Ounces
83 10 010 12 1/2 310
90° red powder-coated
1 5/8 1 42 1 5/8 42 27.5
83 10 015 17 1/2 420 2 3/8 1 1/2 60 2 3/8 60 50.0
83 10 020 22 1/2 560 2 3/4 2 70 2 3/4 70 91.7
83 10 030 25 1/2 650 4 3/8 3 110 4 3/8 110 121.1
83 10 040 29 1/2 750 5 1/8 4 130 5 1/8 130 173.6
832 Pipe Wrenches 45°
DIN 5234
83 20 01545°
■ Swedish pattern ■ 45° angled jaws ■ jaws with offset teeth in
opposite directions ■ teeth additionally induction
hardened ■ I-beam handle design ■ captive adjusting nut ■ red powder-coated,
jaws bright ground
■ Chrome vanadium electric steel; forged, oil-hardened
Clamping widthProduct Number inch mm
Pliers
Ø inch inch Ø mm
inch mm
Ounces
83 20 010 13 320
45° red powder-coated
1 5/8 1 42 1 5/8 42 28.9
83 20 015 17 430 2 3/8 1 1/2 60 2 3/8 60 49.7
83 20 020 22 1/2 570 2 3/4 2 70 2 3/4 70 91.6
833
83 30 015
8360
95
PiPe wrencHes And wAter PumP Pliers
Clamping widthProduct Number inch mm
Pliers
Ø inch inch Ø mm
inch mm
Ounces
83 60 010 13 330 red powder-coated 1 5/8 1/2 42 1 5/8 42 33.7
83 60 015 17 420 red powder-coated 2 3/8 1 1/2 60 2 3/8 60 51.9
83 60 010
Pipe Wrench s-Typewith fast adjustment
■ time-saving, precise adjustment of the opening width at the press of a button directly on the workpiece
■ less effort required due to self-locking mechanism■ no unintentional shifting of the pliers■ high wear-resistance due to the additionally hardened teeth
Pipe Wrenches s-Type DIN 5234
■ slim, S-type jaw ■ jaws with offset teeth in
opposite directions ■ teeth additionally induction
hardened ■ three-point gripping on pipes;
self-locking ■ I-beam handle design ■ captive adjusting nut ■ red powder-coated,
jaws bright ground
■ Chrome vanadium electric steel; forged, oil-hardened
Clamping widthProduct Number inch mm
Pliers
Ø inch inch Ø mm
inch mm
Ounces
83 30 005 9 1 /4 245
red powder-coated
1 1/2 1/2 35 1 1/2 35 16.6
83 30 010 13 320 1 5/8 1 42 1 5/8 42 29.5
83 30 015 17 420 2 3/8 1 1/2 60 2 3/8 60 54.3
83 30 020 21 1/4 540 2 3/4 2 70 2 3/4 70 94.1
83 30 030 26 1/4 680 4 3/4 3 120 3 60/64 100 154.0
83 60 015
96
PiPe wrencHes And wAter PumP Pliers
86Pliers Wrenches
pliers and wrench in a single tool
ISO 5743
86 03 150
86 03 180
86 05 250
86 03 300
86 07 250 sba
meet the Pliers Wrench: A One-Of-A-Kind Tool with Unlimited Possibilities...
From gripping and holding to pressing and bending applications, there is little that the Pliers Wrench can‘t do. With smooth jaws that won‘t damage or mar the surface of workpieces to a push-button adjustment that maintains the tool‘s setting, the Pliers Wrench is everything that you need to get the job done.
■ replaces a full set of inch and metric open end wrenches■ adjustable tightening tool ■ excellent for gripping, holding, pressing and bending applications ■ smooth jaws for careful installation of plated fittings ■ will not round off nuts and bolts and won‘t damage chrome
and other soft finishes ■ parallel jaws allow infinitely variable gripping of all widths
to the specified maximum size ■ reliable catching of the hinge bolt: no unintentional shifting ■ the action of the jaws allows bolted connections to be tightened
and released quickly using the ratchet principle ■ lever transmission greater than 10 - 1 for strong gripping power ■ Chrome vanadium electric steel; forged, oil-hardened
length 6“Mini Pliers Wrench for precision mechanics; ideal multi-purpose wrench in pocket size; perfect for inclusion in emergency tool kits; great for heavy duty use in tight locations
length 7 1/4“with narrow gripping jaws – for fastening/loosening situations requiring a slim tool
Working on plated fittings without damaging the surface
Pliers Wrench: zero-backlash contact pressure, no damage to edges
Conventional open end wrench: edge pressure causes surface damage on edges of nuts and bolts
Works using the ratchet principle Fast adjustment by pushing a button
97
PiPe wrencHes And wAter PumP Pliers
smooth, parallel gripping jaws for work on sensitive surfaces
adjustment at the touch of a button – quick, reliable and precise
infinitely variable adjustment of widths across flats for metric and inch workpieces
cam drive increases force to up to 10 times the applied hand power
DimensionsProduct Number inch mm
Pliers Handles
inch mm
Adjustment positions
B1inch
B2inch
B3inch
B1mm
B2mm
B3mm Ounces
86 03 150 6 150
nickel plated
plastic coated
1 27 14 3/16 9/32 13/32 4.7 7.0 10.5 6.2
86 03 180 7 1/4 180 1 3/8 35 13 13/64 5/16 15/32 5.0 8.0 12.0 9.0
86 03 250 10 250 1 3/4 46 17 5/16 5/16 35/64 8.0 8.0 14.0 19.0
86 03 300 12 300 2 3/8 60 22 3/8 3/8 19/32 9.5 9.5 15.0 25.7
86 05 150 6 150
nickel plated
with multi-component grips
1 27 14 3/16 9/32 13/32 4.7 7.0 10.5 6.8
86 05 180 7 1/4 180 1 3/8 35 13 13/64 5/16 15/32 5.0 8.0 12.0 9.8
86 05 250 10 250 1 3/4 46 17 5/16 5/16 35/64 8.0 8.0 14.0 20.1
86 07 250 sba 10 250 chrome plated
with dipped insulation grips, VDE-tested
1 3/4 46 17 5/16 5/16 35/64 8.0 8.0 14.0 21.7
98
870 KniPeX Cobra® hightech Water Pump Pliers
ISO 8976
87 01 125
87 01 150
87 01 180
87 01 250
87 01 300
87 02 250
87 03 250
meet the Cobra® - The indispensable gripping machine. No more time-consuming test-adjusting to achieve the correct size. Now, simply position the upper jaw to the workpiece, press the button and close the lower jaw. Say “goodbye“ to those awful blood blisters you get with other gripping pliers. We‘ve designed a built-in pinch guard that prevents blood blisters on your hand. Your safety is our first priority.
Innovative. Efficient. Safe. That‘s the KNIPEX Difference.
■ adjustment at the touch of a button directly on the workpiece ■ fine adjustment for optimum adaptation to different size work pieces
and a comfortable gripping position ■ self-locking on pipes and nuts: no slipping on the workpiece
and low hand force required ■ gripping surfaces with special hardened teeth,
teeth hardness approx. 61 HRC; low wear and reliable gripping ■ box-joint design: high stability because of double guide ■ reliable catching of the hinge bolt: no unintentional shifting ■ pinch guard prevents operators' fingers from being pinched ■ Chrome vanadium electric steel; forged, oil-hardened
length 5“for use in precision mechanics, hobbies and in the home; improved access in very confined spaces, perfect for an emergency tool kit
length 7 1/4“good access to the workpiece
length 10“very large gripping capacity; good access to the workpiece; high load capacity having a slim design
Teeth set against the direction of rotation have a self-clamping effect and prevent slipping on the workpiece
Fine adjustment by pushing a button: fast and comfortable
Fast and firm adjustment directly on the workpiece
87 05 250
PiPe wrencHes And wAter PumP Pliers
+ 3
0%
mini-Cobra®: Pocket-sized with the same function as the standard sizes; 1” capacity
30% more capacity than a conventional pipe wrench
Cobr
a®
99
PiPe wrencHes And wAter PumP Pliers
Product Number inch mm
Pliers Head Handles
Ø inch inch Ø mm mm
Adjustment positions Ounces
87 01 125 5 125
grey atramentized polishedwith non-slip plastic coating
1 1 27 27 13 3.0
87 01 150 6 150 1 1/4 1 12/64 32 30 11 5.1
87 01 180 7 1/4 180 1 1/2 1 27/64 42 36 18 6.0
87 01 250 10 250 2 1 13/16 50 46 25 11.1
87 01 300 12 300 2 3/4 2 23/64 70 60 30 19.0
87 02 180 7 1/4 180
grey atramentized polished with multi-component grips
1 1/2 1 27/64 42 36 18 6.9
87 02 250 10 250 2 1 13/16 50 46 25 13.2
87 02 300 12 300 2 3/4 2 23/64 70 60 30 20.4
87 03 125 5 125
chrome platedwith non-slip plastic coating
1 1 25 27 13 3.0
87 03 180 7 1/4 180 1 1/2 1 27/64 42 36 18 6.2
87 03 250 10 250 2 1 13/16 50 46 25 11.1
87 03 300 12 300 2 3/4 2 23/64 70 60 30 19.0
87 05 180 7 1/4 180
chrome platedwith multi-component grips
1 1/2 1 27/64 42 36 18 6.9
87 05 250 10 250 2 1 13/16 50 46 25 13.2
87 05 300 12 300 2 3/4 2 23/64 70 60 30 20.4
100
PiPe wrencHes And wAter PumP Pliers
870 KniPeX Cobra® Xl/XXl
Pipe and Water Pump Pliers
ISO 5743
87 01 400
87 01 560
The KNIPEX Cobra® XL and XXL offer the power and comfort of water pump pliers while being lighter in weight and having a greater gripping capacity than comparable pipe wrenches. The Cobra® Xl can grip a 3 1/2“ pipe coupling and weighs 50% less than 2“pipe wrenches, which have a much lower gripping capacity. With its compact length of 16“, the Cobra XL is perfect for the plumber‘s tool box.
The Cobra® XXl with its capacity of up to 4 1/2“ only weighs as much as 2“pipe wrenches. It‘s 22“ size makes it the biggest pliers around!
■ greater gripping capacity but much lower weight than comparable pipe wrenches
■ fast push-button adjustment directly on the workpiece; no unintentional slipping of the joint
■ fine adjustment for optimum adaptation to different size workpieces and a comfortable handle width
■ self-locking on pipes and nuts: no slipping on the workpiece and low handforce required
■ gripping surfaces with special hardened teeth; teeth hardness approx. 61 HRC: low wear and reliable gripping
■ box-joint design: high stability because of double guide ■ pinch guard prevents operators' fingers from being pinched ■ Chrome vanadium electric steel; forged, oil-hardened
Fine adjustment by pushing a button: fast and comfortable
Grips any shape object: round, square, hex or flat
Product Number inch mm
Pliers Head Handles
Ø inch inch Ø mm mm
Adjustment positions Ounces
87 01 400 16 400 grey atramentized polished plastic coated 3 1/2 3 3/4 90 95 27 42.8
87 01 560 22 560 grey atramentized polished plastic coated 4 1/2 4 3/4 115 120 20 97.0
Self-locking on pipes and nuts: no slipping on the workpiece and less handforce required Fast and firm adjustment directly on the workpiece
101
Cobra® Xl with union nut on 2“screwed pipe connection
to get to a gripping capacity of 3 3/4“ you would otherwise need a 3“ pipe wrench
Cobra® Xl
smaller in size and less weight than 1 1/2“ pipe gripping pliers
2“ pipe gripping pliers
gripping capacity exceeded
Cobr
a®
PiPe wrencHes And wAter PumP Pliers
102
PiPe wrencHes And wAter PumP Pliers
85KniPeX auto adjusting Pliers ISO 8976
85 01 250
Cobra...Redefined.Adjustment to the workpiece is automatic with the KNIPEX Auto Adjusting Pliers! Just grip the pliers handles and squeeze - it‘s that easy!
■ ideal for frequent changeovers to workpieces of different sizes ■ automatic adjustment per one handed operation both for right-handed
and left-handed use ■ good access to the workpiece thanks to the slim dimensions in the
head and joint area and the flush joint bolt■ self-locking on pipes and nuts: no slipping on the workpiece and
low handforce required ■ gripping surfaces with special hardened teeth,
teeth hardness approx. 61 HRC: low wear and reliable gripping ■ box-joint design: high stability because of double guide ■ pinch guard prevents operators' fingers from being pinched ■ locking lever for space saving transport with reliable closed handles ■ Chrome vanadium electric steel; forged, oil-hardened
Automatic adjustment: no time-consuming trial and error adjusting to the correct opening size in case of differently sized workpieces
Locking lever for space saving transport with reliable closed handles
Slim dimensions for good access to the workpiece using one handed operation
Product Number inch mm
Pliers Head Handles
Ø inch inch Ø mm mm Ounces
85 01 250 us 10 250 grey atramentized polished with non-slip plastic coating 1 1/4 1 3/8 32 36 13.1
Self-locking on pipes and nuts means no slipping off the work piece
Automatic adjustment: no time-consuming trial and error adjusting to the correct opening size
103
8726
PiPe wrencHes And wAter PumP Pliers
8721
KniPeX Cobra® vDe
hightech Water Pump Pliers, insulated
ISO 8976 IEC 60900 DIN EN 60900
87 28 250 sba
It‘s easy to achieve the perfect capacity on the KNIPEX Cobra® VDE Pliers. You don‘t even have to push the button! Simply place the upper gripping jaw of the opened pliers on the workpiece and slide the lower handle forward.
■ adjustment by shifting the jaw directly on to the workpiece: fast and reliable
■ opening at the touch of a button off the workpiece ■ fine adjustment for optimum adaptation to different workpiece sizes
and a comfortable gripping position ■ good access to the workpiece due to slim size in the head and
joint area ■ self-locking on pipes and nuts: no slipping on the workpiece and
low handforce required ■ gripping surfaces with special hardened teeth,
teeth hardness approx. 61 HRC: low wear and reliable gripping ■ box-joint design: high stability because of double guide ■ pinch guard prevents operators' fingers from being pinched■ Chrome vanadium electric steel; forged, oil-hardened
Quick adjustment to the workpiece without using the push-button, hands stay behind guard Just push the pliers handle to adjust
Product Number inch mm
Pliers Head Handles
Ø inch Ø mm inch mm
Adjustment positions Ounces
87 28 250 10 250
grey atramentized
polishedinsulated with multi-component grips, VDE-tested
2 50 1 3/4 46 24 12.0
KniPeX Cobra® Quickset
Water Pump Pliers ISO 8976
87 21 250
Product Number inch mm
Pliers Head Handles
Ø inch Ø mm inch mm
Adjustment positions Ounces
87 21 250 10 250 grey atramentized polished with non-slip plastic coating 2 50 1 3/4 46 25 11.8
■ adjustment by shifting the jaw directly on to the workpiece: fast, secure and comfortable handling
■ opening at the touch of a button■ fine adjustment for optimum adaptation to different workpiece sizes
and a comfortable handle width■ good access to the workpiece due to slim size in the head and joint area■ self-locking on pipes and nuts: no slipping on the workpiece and
low handforce required■ gripping surfaces with special hardened teeth,
teeth hardness approx. 61 HRC: low wear and reliable gripping■ box-joint design: high stability because of double guide■ pinch guard prevents operators´ fingers from being pinched■ Chrome vanadium electric steel; forged, oil-hardened
104
The KNIPEX Raptor™ Pliers combines the convenience of the comfortable push-button adjustment on the workpiece and the function of an all-purpose tightening tool. Jaw gripping with zero backlash prevents slipping on the bolt head or rounding edges. Even rusty or thick-coated bolted connections, which usually cannot be gripped by a conventi-onal spanner, can be managed by the exceptionally powerful gripping jaws of this tool.
PiPe wrencHes And wAter PumP Pliers
874 KniPeX RaPToR™ Pliers
ISO 5743
87 41 250
■ for inch and metric nuts and screws with widths across flats from
3/8" up to 1 1/4"; self-locking in the range from 11/16“ on; no slipping on the workpiece
■ zero-backlash gripping of inch or metric hexagonal head screws; no rounding of screw heads
■ reliable and tight gripping of rounded, rusty or overly painted nuts and screws; ideal for work on vehicle brake systems
■ quick tightening of nuts and bolts using ratchet action ■ adjustment at the touch of a button directly on the workpiece,
one handed operation ■ fine adjustment for optimum adaptation to different size workpieces
and a comfortable handle width ■ box-joint design: high stability because of double guide ■ secure catching of the hinge bolt: no unintentional shifting ■ favorable lever action: optimum transmission of force ■ guard prevents operators' fingers from being pinched ■ replaces a set of wrenches; ideal for tightening locknuts ■ Chrome vanadium electric steel; forged, oil-hardened
Grips rusted nuts with rounded edges
Self-locking: no slipping on the workpiece and less effort required KNIPEX Raptor™ Pliers as the second spanner for tightening locknuts
Fine adjustment by pushing a button: fast and comfortable
Product Number
inch mm
Pliers Head Handles
inch mm
Adjustment positions Ounces
87 41 250 RaP 10 250 grey atramentized polished with non-slip plastic coating 3/8 - 1 1/4 10 - 32 15 11.6
105
PiPe wrencHes And wAter PumP Pliers
875 KniPeX Cobra® es
Water Pump Pliers extra-slim
ISO 8976
87 51 250
The KNIPEX Cobra ES is ideal for working in confined areas. Featuring a slim head and long, narrow jaws, this tool reaches into places other pliers can‘t.
■ ideal for service and maintenance, equipment repair, automotive and general industry
■ long, narrow jaws ■ good access to the workpiece due to very slim construction of head
and joint area ■ grips flat material due to the three-point rest■ adjustment at the touch of a button directly on the workpiece ■ fine adjustment for optimum adaptation to different size workpieces
and a comfortable handle width ■ self-locking on pipes and nuts: no slipping on the workpiece
and low handforce required ■ box-joint design: high stability because of double guide ■ secure catching of the hinge bolt: no unintentional shifting ■ favorable lever action: optimum transmission of force ■ guard prevents operators' fingers from being pinched ■ Chrome vanadium electric steel; forged, oil-hardened
Grips nuts up to 1 3/8“ across flats Slim head and joint area (compared to conventional water pump pliers)
Optimum access to the workpiece. Ideal for service and maintenance, equipment repair, automotive and general industry
Fine adjustment by pushing a button: fast and comfortable
Product Number inch
Pliers Head Handles
Ø inch inch
max. parallel opening width
(in inch)
max. gripping depth
(in inch)
Adjustment positions Ounces
87 51 250 10 grey atramentized polished with non-slip plastic coating 1 1/4 1 3/8 1 1/2 1 5/8 19 11.6
Product Number mm
Pliers Head Handles
Ø mm mm
max. parallel opening width
(in mm)
max. gripping depth
(in mm)
Adjustment positions Ounces
87 51 250 250 grey atramentized polished with non-slip plastic coating 32 34 37 42 19 11.6
106
88KniPeX alligator® Water Pump Pliers
ISO 8976
88 01 180
88 01 250
88 02 250
88 07 250
88 08 250
■ self-locking on pipes and nuts: no slipping on the workpiece and low handforce required
■ gripping surface with special hardened teeth, teeth hardness approx. 61 HRC; low wear and reliable gripping
■ box-joint design: high stability because of double guide ■ robust construction; particularly suitable for heavy duty work ■ pinch guard prevents operators' fingers from being pinched ■ Chrome vanadium electric steel; forged, oil-hardened
PiPe wrencHes And wAter PumP Pliers
Self-locking on pipes and nuts; no slipping on the workpiece. Less handforce is required since handles do not need to be squeezed. Simply put pressure on the upper handle for a powerful grip.
meet the alligator®
More output and comfort compared to conventional water pump pliers of the same length: offer 9 adjustment positions for 30% more gripping capacity; good access to the workpiece due to slim size in the head and joint areas
+ 3
0%
107
PiPe wrencHes And wAter PumP Pliers
Product Number inch mm
Pliers Head Handles
Ø inch inch Ø mm mm
Adjustment positions Ounces
88 01 180 7 1/4 180
black atramentized
polishedwith non-slip plastic coating
1 1/2 1 3/8 42.0 36.0 9 6.3
88 01 250 10 250 2 1 3/4 50.0 46.0 9 11.3
88 01 300 12 300 2 3/4 2 3/8 70.0 60.0 9 18.0
88 02 180 7 1/4 180
black atramentized
polished with multi- component grips
1 1/2 1 3/8 42.0 36.0 9 7.6
88 02 250 10 250 2 1 3/4 50.0 46.0 9 12.6
88 02 300 12 300 2 3/4 2 3/8 70.0 60.0 9 20.0
88 07 250 10 250 black atramentized
chrome plated
plastic dipped insulated 2 1 3/4 50.0 46.0 9 11.3
88 08 250 sba 10 250
black atramentized
polishedinsulated with multi-component grips, VDE-tested
2 1 3/4 50.0 46.0 9 13.7
Conventional water pump pliers
KniPeX alligator®
specially hardened teethhigh resistance to wear, allowing continuous and reliable gripping
robust adjusting mechanisminsensitive to dirt; particularly suitable for outdoor work
9 adjustment position
box joint, double guide
Alli
gato
r®
no loosening of the joint connection; heavy duty
30% more gripping capacity, optimized adjustment to the workpiece and a comfortable gripping position; slim size
The Alligator® 250 mm grips the union nut in a 3/4“ screw connection with comfortable handle positioning
3/8“ union nuts are out of the gripping range of conventional water pump pliers
Alligator® 300: 2 3/4“ capacity compared to the 1 1/2“ capacity of conventional pipe wrenches
alligator® 250: convincing alternative
alligator® 300 instead of a 1 1/2“ pipe wrench
108
PiPe wrencHes And wAter PumP Pliers
90mini Water Pump Pliers with groove joint
ISO 8976
90 01 125
■ easy, convenient engagement in 4 different positions ■ tongue and groove slip joint ■ all strain removed from the joint screw; no wear on pivot ■ pinch guard prevents operators‘ fingers from being pinched ■ Chrome vanadium electric steel; forged, oil-hardened
Product Number inch mm
Pliers Head Handles
Ø inch inch Ø mm mm Ounces
90 01 125 5 125 black atramentized polished plastic coated 5/8 1/2 17 14 3.6
109
sPeciAl Pliers And sPeciAl tools
9020 Pipe Cutter
for plastic conduit pipes and flexible hoses
90 20 185
Turning the cutter slightly when operating prevents brittle pipes from splitting or breaking.
■ for cutting thin-walled plastic pipes (conduit plastic pipes) and flexible hoses, also with fabric reinforcement, of plastic and rubber up to 1“ exterior dia.
■ not suitable for cutting cables ■ with opening spring and locking
lever ■ tool body: plastic, fiberglass –
reinforced ■ blade: Special tool steel; oil-
hardened, interchangeable With replaceable blade
Cutting capacitiesProduct Number inch mm
Ø inch Ø mm
Ounces
90 20 185 7 1/4 185 1 25 6.1
90 29 185 Spare blade for 90 20 185
9025 Pipe Cutter
for composite pipes and corrugated conduit
90 25 20
■ for cutting composite pipes with diameters of 1/2“ - 1“ and for cutting flexible corrugated conduit pipes with a diameter of 3/4“ - 1 3/8“ without damaging the pipe inside
■ a calibration arbor can be fitted, for example for Geberit composite pipes with 29/64“ and 38/64“ dia.
■ tool body: High-grade chrome vanadium electric steel; oil-hardened ■ blades: Special tool steel; oil-hardened, interchangeable
Composite pipes of 1/2 - 1“dia. are cut cleanly and without deformation
Clean cut of corrugated conduit 3/4“ - 1 3/8“ dia.
Cutting capacitiesProduct Number inch mm
Tool Handles composite pipesØ inch
protective pipesØ inch
Blade lengthinch
composite pipesØ mm
protective pipesØ mm
Blade length
mm Ounces
90 25 20 8 1/4 210 galvanized with multi-component grips 1/2 - 1 3/4 - 1 3/8 1 12 - 25 18 - 35 25 11.7
90 29 01 Spare blade for 90 25 20 (composite pipes)90 29 02 1 pair of spare blades for 90 25 20 (protective pipes)90 29 15 Calibration arbor for 90 25 20 (Geberit pipes)
110
9025 Pipe Cutter for composite and plastic pipes
90 25 40
■ for cutting thick-walled plastic and composite pipes with diameters from 1 - 1 37/64“
■ cuts pipes using the ratchet principle in several strokes ■ self-adapting pipe support positions pipes of various diameters
correctly for a rectangular cut ■ tool body: High-grade chrome vanadium electric steel, oil-hardened ■ blade: Special tool steel; oil-hardened, interchangeable
Clean cut of thick-walled plastic and composite pipes
Not suitable for thin-walled conduit pipes. Please use article number 90 20 185 for those
Cutting capacities Cutting edge lengthProduct Number inch mm
Tool Handles Ø inch Ø mm inch mm
Ounces
90 25 40 8 1/4 210 galvanized with multi-component grips 1 - 1 37/64 26 - 40 1 37/64 40 17.6
90 29 40 Spare blade for 90 25 40
904 Punch lock Riveters
90 42 250
90 42 340
■ to join metal section sheets used in drywalling with a lock seam ■ for U- and C-shaped sections with max 3/64“ (5/64 x 1/64) metal ■ minimal handforce required due to optimum lever transmission ■ pliers body: Special tool steel; rolled, oil-hardened
90 42 250for one handed operation
Preparing the pliers for connection of two metal section sheets
The punching tool is squeezed through the metal section sheets
CapacityProduct Number inch mm
Pliers Handles
Ounces
90 42 250 10 250 burnished with multi-component grips 3/64“ (5/64 x 1/64) max. 1,2 (2 x 0,6) 23.8
90 42 340 13 2/5 340 burnished with multi-component grips 3/64“ (5/64 x 1/64) max. 1,2 (2 x 0,6) 31.8
90 49 340 Spare punch for 90 41 340 and 90 42 34090 49 340 m Spare die for 90 41 340 and 90 42 340
sPeciAl Pliers And sPeciAl tools
111
sPeciAl Pliers And sPeciAl tools
9055 sheet metal nibbler
90 55 280
■ for cutting iron, copper or aluminium sheet metal up to max. 3/64“ thickness, plastic up to max. 5/64“ thickness
■ materials are cut without deformation ■ clean-cut edges ■ with chip breaker ■ easy handling ■ cutting width: 7/64“ ■ tool body: Special tool steel; rolled, oil-hardened ■ blade: Special tool steel; oil-hardened, interchangeable
Notching and chip breaking in a single pass Notching without chip breaking
Product Number inch mm
Tool Handles
Ounces
90 55 280 11 280 nickel plated
with multi-component grips
16.3
90 59 280 Spare blade for 90 55 280
9061 notching Pliers
90 61 20
The KNIPEX Notching Pliers produce the most common notches in plastic ledges and cable ducts in a simple, fast and clean way. No time-consuming sawing out or nibbling and no additional work required.
■ special pliers for notching recesses into plastic ledges and plastic casings for electric and sanitary installation
■ notches can be enlarged by initial and final cut ■ clean-cut edges ■ easy handling ■ with opening spring, opening limiter and locking lever ■ pliers body: Special tool steel; rolled, oil-hardened
CapacityProduct Number inch mm
Pliers Handles
Ounces
90 61 16 10 250 burnished with plastic grips
5/8 - 1 1/4“ 16 x 32 mm 14.2
90 61 20 10 250 51/64 - 1 9/64 20 x 29 mm 14.6
112
907 Revolving Punch Pliers
90 70 220
■ for punching out holes in leather, textiles and plastic materials ■ with six interchangeable punches:
5/64, 3/32, 1/8, 9/64, 5/32, 13/64 in dia.■ with opening spring and locking lever ■ powder coated for reliable protection against rust ■ pliers body and punches: Special tool steel; oil-hardened
Interchangeable punches
Product Number inch mm
Pliers Finish
Ounces
90 70 220 8 3/4 220 red powder coated
powder coated 8.9
913 glass breaking Pincer
ISO 5743
91 31 180
■ for breaking glass to a scored line ■ Special tool steel; forged, oil-hardened
Jaw widthProduct Number inch mm
Pliers Head Handles inch mm
Ounces
91 31 180 7 1/4 180 black atramentized polished plastic coated 15/16 24.0 8.6
sPeciAl Pliers And sPeciAl tools
113
sPeciAl Pliers And sPeciAl tools
91glass nibbling Pincers ISO 5743
91 51 160
■ for breaking off narrow strips of glass to a scored line ■ for finishing off glass edges to required profile ■ Special tool steel; forged, oil-hardened
Jaw widthProduct Number inch mm
Pliers Head Handles inch mm
Ounces
91 51 160 6 1/4 160 black atramentized polished plastic coated 3/8 9.5 5.2
91 71 160 6 1/4 160 black atramentized polished plastic coated 5/32 4.0 5.0
916 Flat nose grozing Pliers
ISO 5743
91 61 160
■ with soft gripping jaws ■ for trimming glass edges, e.g. when making leaded glass windows ■ Special tool steel; forged, oil-hardened
Jaw widthProduct Number inch mm
Pliers Head Handles inch mm
Ounces
91 61 160 6 1/4 160 black atramentized polished plastic coated 3/8 9.5 5.0
91 71 160
114
Precision tweezers
92Precision Tweezers needle-pointed shape
92 22 12
92 22 13
■ for ultra fine mounting work ■ extra fine tips ■ smooth gripping surfaces ■ stainless, non-magnetic ■ non-reflective matte finish
92 22 12straight pattern
92 22 13solid; straight pattern; stainless, non-magnetic and acid-proof
Product Number inch mm
Finish
Ounces
92 22 12 4 105 stainless, non-magnetic 5.0
92 22 13 5 1/4 135 stainless, non-magnetic, acid-proof 7.0
92Precision Tweezers with dowel pin pointed shape
92 22 35
92 34 36
45°
■ universally applicable ■ narrow tips ■ gripping surfaces with fine transverse serration ■ serrated handles
92 22 35straight pattern; non-reflective matte finish; stainless, non-magnetic and acid-proof
92 34 36bent tips; nickel plated
Product Number inch mm
Finish
Ounces
92 22 35 6 155 stainless, non-magnetic, acid-proof 8.0
92 34 36 6 155 45° nickel plated 8.0
92Precision Tweezers blunt shape
92 70 46
■ universally applicable ■ straight pattern ■ wide, round tips ■ serrated handles
92 70 46round tips, approx. 9/64 in wide; gripping surfaces with fine transverse serrations; black, non-reflective lacquered
Product Number inch mm
Finish
Ounces
92 70 46 5 3/4 145 black lacquered 9.0
115
Precision tweezers
92Precision Tweezers esD
92 08 78 esD
45°
92 28 69 esD
92 38 75 esD
45°
92 58 74 esD
92 08 78 esDfor SMD-technology*; bent tips; smooth gripping surfaces
92 28 69 esDstraight pattern; strong tip; smooth gripping surfaces
92 38 75 esDsickle-shaped tips; smooth gripping surfaces
92 58 74 esDround tips, approx. 5/64 in. wide; straight pattern; smooth gripping surfaces
Product Number inch mm
Finish
Ounces
92 08 78 esD 4 3/4 120 45° stainless, non-magnetic, electrically dissipative 5.6
92 28 69 esD 5 1/4 130 stainless, non-magnetic, electrically dissipative 7.0
92 38 75 esD 4 3/4 120 45° stainless, non-magnetic, electrically dissipative 6.0
92 58 74 esD 4 3/4 120 stainless, non-magnetic, electrically dissipative 7.0
■ Chrome nickel steel: stainless, non-magnetic (18/10); very popular electronics quality
■ ESD coating: non-reflective black, with a surface resistance of approx. 105 Ohm
■ tips: non-reflective, brushed ■ gripping surfaces: matte-finish for optimum grip
92Precision Tweezers insulated
IEC 60900 ASTM F1505
92 27 61
92 27 62
92 37 64
45°
92 67 63
■ insulated and tested according to IEC 60900 : ASTM F1505 ■ plastic dipped insulated ■ nickel plated ■ Spring steel, high-strength
92 27 61for ultra fine mounting work; extra fine tips; straight pattern; gripping surfaces matte-finished for optimum grip
92 27 62straight pattern; gripping surfaces with fine transverse serration
92 37 64bent tips; gripping surfaces with fine transverse serration
92 67 63straight pattern; serrated gripping surfaces
Product Number inch mm
Finish
Ounces
92 27 61 5 1/4 130 plastic dipped insulated 1.1
92 27 62 6 150 plastic dipped insulated 1.2
92 37 64 6 150 45° plastic dipped insulated 1.2
92 67 63 5 3/4 145 plastic dipped insulated 1.5
* SMD-Technology: technique for soldering surface-mounted components on printed circuit boards without using holes. Technical change and errors excepted
116
cAble And wire roPe sHeArs
95
95
Cable shears IEC 60900 ASTM F1505
95 06 230
■ insulated and tested according to IEC 60900 / ASTM F 1505■ not suitable for ACSR, steel wire and hard drawn copper conductors ■ precision ground, hardened blades ■ no crushing■ with pinch guard and slip guard ■ adjustable bolted joint ■ shears body: Surgical steel; stainless, air-hardened ■ handles: plastic, impact-resistant
95 06 230for copper conductors single wire up to 16 mm2, multiple wire up to 1/0 AWG, fine- stranded up to 70 mm2 and aluminium conductors multiple wire up to 70 mm2; easy cutting with one handed operation due to high transmission ratio; stainless – surgical steel, oil-hardened and tempered
Cutting capacitiesProduct Number inch mm
Head Handles
Ø inch Ø mm mm²
AWG
Ounces
95 06 230 9 1/4 230 polished plastic insulated, VDE-tested 5/8 16.0 50 1/0 9.7
Cable shears
95 11 165
95 12 165
95 21 165 sba
95 22 165
■ for cutting copper and aluminium cables, single and multiple wire ■ not suitable for ACSR, steel wire and hard drawn copper conductors ■ precision ground, hardened blades ■ clean and smooth cut without crushing and deformation ■ easy cutting with one hand operation ■ with pinch guard and slip guard ■ adjustable bolted joint, self-locking screw■ High-grade special tool steel; forged, oil-hardened
style 2internal opening spring, protected and captive
Cut performed with a Diagonal Cutter: high effort required, inaccurate cut, considerable deforming and crushing of the cable
Cut performed with a Cable Shear: easy, clean cut without any deformation of the cable95 18 165 sba
117
cAble And wire roPe sHeArs
951 Cable shears with twin cutting edges
95 11 200
95 12 200
95 18 200 sba
The double cutting edge allows a comfortable handle position in all cutting situations inside the specified cutting capacity.
■ for cutting copper and aluminium cables ■ not suitable for ACSR, steel wire and hard drawn copper conductors ■ precision ground, hardened blades ■ clean and smooth cut without crushing and deformation ■ by dividing the cutting actions into initial cut (insulating sheath in the
front cutting area) and final cut (conductor in the back cutting area), cables up to Ø 51/64“ can be cut in one handed operation
■ less effort required due to favorable lever ratio and optimized cutting edge geometry
■ with pinch guard and slip guard■ adjustable screw joint, self-locking ■ High-grade special tool steel; forged, oil-hardened
95 18 200 sba■ insulated and tested according to IEC 60900 and ASTM F1505
initial cut: Using the front cutting edge to cut the insulating sheath on larger cable diameters leaves an ergonomic handle opening width.
Final cut:After cutting the sheath in the front profile,the cut is finished through the metal partof the cable in the rear profile. Initial cutin the front profile, final cut in the rearprofile – to keep it as easy as possible.
Cutting capacitiesProduct Number inch mm
Tool Handles
Ø inch Ø mm mm²
AWG
Ounces
95 11 200 8 200 burnished plastic coated 51/64 20.0 70 2/0 10.0
95 12 200 8 200 - burnished with multi-component grips 51/64 20.0 70 2/0 11.4
95 18 200 sba 8 200 burnishedinsulated with multi-component grips, VDE-tested
51/64 20.0 70 2/0 12.0
Cutting capacitiesProduct Number inch mm
Style Tool Handles
Ø inch Ø mm mm²
AWG
Ounces
95 11 165 6 1/4 165 1 burnished plastic coated 19/32 15.0 50 1/0 7.6
95 12 165 6 1/4 165 1 burnished with multi-component grips 19/32 15.0 50 1/0 8.8
95 18 165 sba 6 1/4 165 1 burnished insulated with multi-component grips, VDE-tested
19/32 15.0 50 1/0 8.8
95 21 165 6 1/4 165 2 burnished plastic coated 19/32 15.0 50 1/0 7.6
95 22 165 6 1/4 165 2 burnished with multi-component grips 19/32 15.0 50 1/0 9.0
118
Cable anD WiRe RoPe sheaRs
95Cable shears
95 12 500
95 17 500
■ for cutting copper and aluminium cables, single and multiple wire ■ not suitable for ACSR, steel wire and wire ropes ■ precision ground, hardened blades ■ clean and smooth cut without crushing and deformation ■ low handforce required due to favorable lever ratio and new
blade geometry ■ short design, length only 20“ ■ lightweight ■ with pinch guard ■ adjustable bolted joint ■ cutter head: Vanadium electric steel;
forged, oil-hardened ■ handle shank: aluminium tube,
high-strength
95 17 500■ insulated and tested according to
IEC 60900 and ASTM F1505
Large cutting capacity: max. 1“ dia. / cap. max. AWG 5/0
Cutting capacitiesProduct Number inch mm
Head Handles
Ø inch Ø mm mm²
AWG
Ounces
95 12 500 20 500 burnished with multi-component grips 1 27.0 150 5/0 38.4
95 17 500 20 500 polished plastic dipped insulated, VDE-tested 1 27.0 150 5/0 52.1
953 Cable Cutters (ratchet action)
95 31 250
95 31 280
■ for cutting copper and aluminium cables, single and multiple wire ■ not suitable for ACSR, steel wire and wire ropes ■ precision ground, hardened blades ■ clean and smooth cut without crushing and deformation ■ one handed operation using ratchet principle ■ little handforce required due to very high transmission ratio ■ two-stage ratchet drive for easy cutting ■ simple handling as a result of light weight and compact design –
can be used even in confined areas ■ with pinch guard and slip guard■ High-grade special tool steel; forged, oil-hardened
95 31/36 280suitable for aluminium sector cable up to 4 x 150 mm2
95 31 280: Large cutting capacity: max. 2“ dia. / cap. max. 750 MCM
Ratchet principle and two-stage ratchet drive for easier cutting
119
cAble And wire roPe sHeArs
953 Cable Cutters (ratchet action)
95 36 250
95 31 250/280: fixed handle with support area as an aid to position the pliers when cutting
Cutting capacitiesProduct Number inch mm
Tool Handles
Ø inch Ø mm mm²
MCM
Ounces
95 32 320 12 1/2 320 black atramentized with multi-component grips 2 23/64 60.0 600 1200 28.2
95 36 320 12 1/2 320 black atramentizedinsulated with multi-component grips, VDE-tested
2 23/64 60.0 600 1200 28.2
95 39 280 Movable spare blade for 95 31 280 / 95 36 280
Cutting capacitiesProduct Number inch mm
Tool Handles
Ø inch Ø mm mm²
MCM
Ounces
95 31 250 10 250 black lacquered with multi-component grips 1 1/4 32.0 240 500 23.8
95 31 280 11 280 black lacquered with multi-component grips 2 52.0 380 750 30.3
95 36 250 10 250 black lacqueredinsulated with multi-component grips, VDE-tested
1 1/4 32.0 240 500 23.0
95 36 280 11 280 black lacquered insulated with multi-component grips, VDE-tested
2 52.0 380 750 29.5
953 Cable Cutters (ratchet action)
95 32 320
95 36 320
sturdy. easy to use. innovative ratchet-drive. For cable up to 2 23/64“ in diameter.
■ easy handling due to low weight (28.2 oz) and compact construction (12 1/2“ length) – usable in confined areas
■ cutting through copper and aluminium cables with diameters of up to 2 23/64“ in one handed and two handed operation
■ hardened cutting edges, precisely ground, cut smoothly and neatly without crushing
■ for cutting copper and aluminium single conductors as well as multiple stranded cables
■ not suitable for cutting ACSR, steel wire and wire ropes■ innovative three-stage ratchet-drive with high leverage for easy cutting
in one handed and two handed operation■ with pinch guard and slip guard■ fixed handle with support area for laying down the pliers when cutting■ High-grade special tool steel; forged, oil-hardened
95 36 320■ insulated and tested according to IEC 60900 and ASTM F1505
95 36 250 / 280insulated and tested according to IEC 60900 and ASTM F1505
120
cAble And wire roPe sHeArs
9532 Cable shears (ratchet action)
with telescopic handles
95 32 038
The handles are adjustable in length and can be angled for easier work: set the handle length to the optimum lever for powerful cutting; put the handle at an angle for an ergonomic gripping position.
■ for cable diameters up to 1 1/2“; handles can be positioned at an angle to set the optimum handle width; also suitable for work in confined areas
■ comfortable work thanks to ratchet action and light weight ■ heavy duty telescopic handles made of oval aluminium tubing;
extendable up to 30“ for maximum leverage on large cable diameters; retractable down to 22“ for minimum space requirements during transport
■ replaceable cutting head ■ extensive cutting range up to max.
Ø 1 1/2“ or max. 550 MCM in copper and aluminium cables
■ easier, neater cut due to optimized cutting edge geometry
■ adjustable bolted joint ■ cutting head: Special quality, high-grade
tool steel; oil-hardened■ handles: high-strength oval aluminium
tubing
Setting of a favorable handle position After the first partial cut, the handles open by ratchet
Repeat cutting and opening actions until the cable is cut through
Adjustment button
Cutting capacitiesProduct Number inch mm
Head Handles
Ø inch Ø mm mm²
MCM
Ounces
95 32 038 22 560 burnished with multi-component grips 1 1/2 38.0 280 550 69.8
95 39 038 Spare cutter head for 95 32 038
Cable shears with adjustable telescopic handles allow angular positioning
easier, neater cut due to optimized
cutting head: Special quality, high-grade
handles: high-strength oval aluminium
Repeat cutting and opening actions until the Repeat cutting and opening actions until the
121
cAble And wire roPe sHeArs
9532 Cable Cutters (ratchet action)
with telescopic handles
95 32 060
■ for copper and aluminium cables, single and multiple wire – also with hard rubber or plastic sheath
■ not suitable for steel wire and wire ropes
■ also suitable for cables with sheet metal sheath
■ little handforce required for cutting due to optimum transmission ratio
■ with pinch guard ■ high cutting capacity due to two
handed operation and ratchet action
■ the blade can be opened in any cutting position
■ blade: Special quality, high-grade tool steel; oil-hardened
■ handles: high-strength oval aluminium tubing
Cutting capacitiesProduct Number inch mm
Head Handles
Ø inch Ø mm mm²
MCM
Ounces
95 32 060 24 3/4 630 burnished with multi-component grips
2 23/64 60.0 740 1400 135.0
95 32 100 26 680 3 15/16 100.0 960 1900 176.0
95 39 720 Movable spare blade for 95 31 720 / 95 32 060
95 39 870 Movable spare blade for 95 31 870 / 95 32 100
old: with steel tubing
new: with heavy-duty aluminium
telescopic shanks
30% reduction in weight
■ handle length with multiple position adjustment from 15 3/4“ - 23 5/8“ (short transport length, individual adaptation to working conditions)
122
Crimping of the end ferrule onto the traction cable
Crimping of the end caps on the Bowden cable sheath
Precise guiding through a bolted joint
Transport lock and restricted opening
Crimp profiles
Internal opening spring
cAble And wire roPe sHeArs
956 Wire Rope shears forged
double function: neat cutting, precise crimping
95 61 190
95 62 190
Cuts all wire ropes without splaying or fanning out, including strong materials like tire cord.
■ with two crimping dies for end caps on Bowden cable sheaths and end ferrules for wire rope
■ comfortable work thanks to slim design and internal opening spring
■ bolted joint for precise blade guidance, readjustable ■ high leverage for reduced effort ■ cutting edge hardness approx. 64 HRC ■ Chrome vanadium heavy-duty steel; forged, oil-hardened
Cutting capacitiesProduct Number inch mm
Head Handles
Ø inch Ø inch Ø inch Ø inch Ø mm Ø mm Ø mm Ø mm Ounces
95 61 190 7 1/2 190 polished plastic coated 9/32 1/4 5/32 7/64 7.0 6.0 4.0 2.5 11.0
95 62 190 7 1/2 190 polished with multi-component grips
9/32 1/4 5/32 7/64 7.0 6.0 4.0 2.5 11.0
123
cAble And wire roPe sHeArs
956 bowden Cable Cutter
95 61 150
■ for Bowden cables and soft wire rope up to 1/8“ dia. (also V2A)
■ smooth and clean cutting due to special shape of the cutting edges
■ sickle shape cutting edges surround the material and prevent the wire rope fanning out
■ little handforce required due to very high transmission ratio
■ with opening spring and locking lever
Cutting capacitiesProduct Number inch mm
Shears Head Handles
Ø inch Ø mm Ounces
95 61 150 6 150 black atramentized polished plastic coated 1/8 3.0 7.2
■ cutting edges additionally induction hardened
■ High-grade special tool steel; forged, oil-hardened
95Wire Rope and Cable Cutters
95 71 600
95 77 600
■ for ACSR, wire ropes and steel rods, copper and aluminium cables
■ angular cutting blades prevent fanning out
■ optimum transmission ratio for high cutting performance
■ bolted cutter head; replaceable ■ lightweight ■ cutter head: High-grade special tool steel; oil-hardened ■ handles: aluminium,
high-strength, drop forged
95 77 600■ insulated and tested according to
IEC 60900 and ASTM F1505
Cutting capacitiesProduct Number inch
Head Handles
inch Ø inch Ø inch
AWG
Ounces
95 71 445 17 1/2 polished with plastic grips 3 3/4 25/64 9/32 3/0 38.2
95 71 600 23 1/2 polished with plastic grips 5 29/32 35/64 23/64 5/0 60.5
95 77 600 23 1/2 polished plastic dipped insulated 5 29/32 35/64 23/64 5/0 83.2
Product Number mm
Head Handles
mm² Ø mm Ø mm
AWG
Ounces
95 71 445 445 polished with plastic grips 95 10.0 7.0 3/0 38.2
95 71 600 600 polished with plastic grips 150 14.0 9.0 5/0 60.5
95 77 600 600 polished plastic dipped insulated 150 14.0 9.0 5/0 83.2
95 79 445 Spare cutter head for 95 71 445
95 79 600 Spare cutter head for 95 71 600 / 95 77 600
95 89 600 Spare cutter head for 95 81 600
124
crimPing Pliers
972 Crimping Pliers
97 21 215
97 22 240
■ for cutting cables, stripping wire and crimping insulated and non-insulated terminals, connectors and plug type connectors
■ with threaded holes for cutting copper and brass screws threaded M 7/64, 1/8, 9/64, 5/32 and 13/64“
■ Special steel; high-strength
Number of crimping positions
Product Number inch mm
Pliers Handles Applications Capacitymm²
AWG
Ounces
97 21 215 8 1/2 215 burnished with plastic gripsinsulated terminals and plug connectors
0.75 - 6.00 10 - 18 3 7.9
97 22 240 9 1/4 240 black lacquered with multi- component grips
insulated terminals and plug connectors
0.75 - 6.00 10 - 18 3
10.6non-insulated open plug-type connectors (plug width 6,3 mm)
0.50 - 6.00 10 - 20 3
9732 Crimping Pliers
97 32 225
■ for cutting cables, stripping wire and crimping insulated and non-insulated terminals and connectors
■ with threaded holes for cutting copper and brass screws threaded M 7/64, 1/8, 9/64, 5/32 and 13/64“
■ Special steel; high-strength
Number of crimping positions
Product Number inch mm
Pliers Handles Applications Capacitymm²
AWG
Ounces
97 32 225 9 225 burnished with plastic grips
insulated terminals and plug connectors
0.5 - 6.0 10 - 20 3 8.5
non-insulated terminals and plug connectors
0.5 - 2.5 13 - 20 3
125
crimPing Pliers
9743 Crimp system Pliers
for exchangeable crimping dies
97 43 200
97 43 200 a
With the possibility of crimping almost all currentlyavailable crimping connections with just one tool andstate-of-the-art crimping pliers technology, the Crimp System Pliers solves almost all tasks in mobile andstationary crimping technology and is an excellent toolfor professionals to use for standard crimping.
■ just one tool for almost 1,000 crimping applications ■ almost parallel crimping movement ■ repetitive, high crimping quality due to precision dies and integral lock
(self-releasing mechanism) ■ crimping pressure has been set precisely (calibrated) in the factory ■ optimum transmission of force due to lever action for fatigue-reduced
operation ■ ergonomically designed handles ■ different locators for precise positioning of the connectors ■ crimp dies for applications not covered in the range offered are
available upon request. ■ Chrome vanadium electric steel in special quality; oil-hardened
97 43 200in a plastic case; foam insert with recesses for crimping dies and locators; with service tool (Allen key), screws and nuts; without crimping dies
97 43 200 apliers without crimping dies, without case
97 43 05with attached crimping dies for non-insulated open plug-type connectors (3/16 and 1/4“ connector width)
97 43 06with attached crimping dies for insulated terminals and plug connectors
Crimp System Pliers 97 43 200 with crimping dies 94 49 30 for non-insulated butt connectors
Crimp System Pliers 97 43 200 with crimping dies 97 49 35 for spark plug connectors
97 43 200 with crimping dies 97 49 61 and locator 97 49 90 for turned types of connectors with varying pin diameters, revolvable
97 43 400 Crimp System Pliers with crimping dies 97 49 24 and locator 97 49 93 for D-Sub plugs
Product Number inch mm
Pliers Handles Applications Capacitymm²
AWG Number of crimping positions Ounces
97 43 200 8 200 burnished with multi-component grips see crimping dies profile table 34.9
97 43 200 a 8 200 burnished with multi-component grips see crimping dies profile table 20.2
97 43 05 8 200 burnished with multi-component gripsCrimp System Pliers for non-insu-lated open plug-type connectors (3/16 and 1/4 in connector width)
0.5 - 6.0 10 - 20 3 21.8
97 43 06 8 200 burnished with multi-component grips Crimp System Pliers for insulated terminals and plug connectors
0.5 - 6.0 10 - 20 3 21.5
126126
crimPing Pliers
9749 Crimping Dies for Crimp system Pliers
Number of crimping positions Ounces
Product Number
Applications Capacitymm²
AWG Capacity SW inch
Capacity SW mm
SleevesØ inch
SleevesØ mm
97 49 04 non-insulated Spade Plug Connectors
0.1 - 2.5 13 - 27 4 1.5
97 49 05 non-insulated Spade Plug Connectors
0.5 - 6.0 10 - 20 3 1.6
97 49 06 insulated terminals and plug connectors 0.5 - 6.0 10 - 20 3 1.6
97 49 08 End Sleeves (ferrules) 0.25 - 6.0 10 - 23 5 1.7
97 49 09 End Sleeves (ferrules) 10 / 16
/ 25 3 / 5 / 7 3 1.8
97 49 13 non-insulated terminals and plug connectors 0.5 - 10.0 7 - 20 4 1.3
97 49 15 Spade Plug connectors and non-insulated open plug type connectors (plug width 6,3 mm)
1.25-2.5 + 3.0-6.0
13 - 17 9 - 12 2 + 1 2.0
97 49 16 insulated terminals and plug connectors 10.0 - 16.0 5 / 7 2 1.6
97 49 18 Twin end sleeves (ferrules) for two flexible conductors
2x6 10 / 16 5 / 7 / 10 3 1.7
97 49 19 End Sleeves (ferrules) 35 - 50 0 / 2 2 1.6
97 49 20 F-connectors for TV and satellite conncetions
9/3221/64 21/64
7.0 8.4 8.1
19/64 3/8 3/8
7.7 9.5 9.5
3 1.8
97 49 23 non-insulated terminals and plug connectors 16 + 25 3 + 5 2 1.6
97 49 24 D Sub; HD 20; HDE plug 0.03 - 0.56 20 - 32 3 1.4
97 49 30 non-insulated butt connectors1.5 - 4.0
6.0 + 10.0*11 - 15 7 + 10
3 2 1.3
97 49 35 Spark plug connectors and distributors 1 17 5 1.8
97 49 40 Coax connectors RG 58, 59, 62, 71, 223
7/321/4
5/64
5.46.481.72
1/419/645/64
6.47.62.1
3 2.0
97 49 44 rolled contacts 0.14 - 1.5 15 - 26 3 1.6
97 49 50 Coax connectors / Car phone RG 58, 174, 188, 316
1/8; 11/64; 7/32; 5/64;
3/64
3.25; 4.52; 5.41; 1.72;
1.07
5/32; 7/32; 1/4; 5/64; 3/64; 3/64
3.9, 5.4; 6.4; 2.1; 1.3; 0.95
6 1.7
97 49 54 modular plugs 0.5 - 2.5 13 - 20 4 1.7
97 49 59 Solar cable connector Helios H4 (Amphenol)
2.5 + 4.0 + 6.0 mm² 10 - 13 3 1.2
97 49 60 turned contacts (HTS + Harting) 0.14 - 4.0 11 - 26 4 1.9
97 49 62 Solar connectors (Huber + Suhner) 2.5 + 4.0 11 + 13 3 1.4
97 49 64 ABS connectors 1.0 - 6.0 10 - 17 2 2.6
127
* compression joints in conformance to DIN 46267
crimPing Pliers
97locators for crimping pliers and crimping dies
Locator 97 59 65 2 for four-mandrel crimping pliers, adjustable in length and diameter for various plugs
Product Number
Applications
Ounces97 49 59 1 Locator for 97 49 59 1.9
97 49 65 1 Locator for 97 49 65 (solar connectors MC3) 2.5
97 49 66 1 Locator for 97 49 66 (solar connectors MC4) 2.5
97 49 68 1 Locator for 97 49 68 (solar connectors Solarlok) 2.5
97 49 69 11 Locator for 97 49 69 1 and 97 49 69 2 1.9
97 49 90 Locator for 97 49 60 (HTS+Harting) 2.4
97 49 93 Locator for 97 49 24 (D-Sub-plugs) 1.4
97 49 94 Locator for 97 49 04 / 97 52 04 / 97 52 34 2.4
97 49 95 Locator for 97 49 05 / 97 52 05 / 97 52 35 0.8
97 59 65 2 Locator for 97 52 65 / 97 52 65 A / 97 52 65 DG / 97 52 65 DG A 8.4
9749
* Pressverbinder nach DIN 46267
97 49 66 4 MC4 (Multi-Contact) solar connectors cutting – stripping – crimping
4.0 11 1 1.2
97 49 66 6 MC4 (Multi-Contact) solar connectors cutting – stripping – crimping
6.0 10 1 1.2
97 49 69 1 Solar connectors (Wieland) 1.5 - 2.5 13 + 15 2 1.2
97 49 69 2 Solar connectors (Wieland) 4.0 - 10.0 7 - 11 3 1.2
97 49 70 Western plugs
4, 6, 8-poles RJ
10 / 11 / 12 / 45
3 2.5
97 49 74 unshielded Molex plugs4, 6, 8-poles RJ 10 / 11 /
12 / 453 1.5
97 49 76 shielded Stewart plugs 2 1.8
97 49 81 Harting connectors for fiber optics1/8
3/161/4
3.04.956.5
9/6415/6419/64
3.56.07.5
3 1.8
97 49 82 Telegärtner connectors for fiber optics 1/8
9/6411/64
3.253.654.52
9/64 5/327/32
3.64.05.4
3 2.0
97 49 83 F-SMA, ST-,SC + STSC/K-connectors for fiber optics
9/6411/6413/64
3.654.25.0
11/647/321/4
4.35.46.0
3 2.1
97 49 84 Harting/Suhner connectors for fiber optics
5/3211/643/16
3.84.3
4.95
11/6413/641/4
4.55.26.0
3 1.8
97 49 87 F-SMA, ST and MIC connectors for fiber optics 11/32 8.7 3/8 9.5 1 1.6
Number of crimping positions Ounces
Product Number
Applications Capacitymm²
AWG Capacity SW inch
Capacity SW mm
SleevesØ inch
SleevesØ mm
128
9751 Crimping Pliers for Western plugs
97 51 10
■ professional tool for cutting and stripping unshielded ribbon telephone cables
■ for crimping 6- and 8-pole Western plugs type RJ 11/12 (3/8“ width) and type RJ 45 (15/32“ width)
■ exact crimping process due to parallel crimping
■ repetitive, high crimping quality due to integral lock (self-releasing mechanism)
■ optimum transmission of force due to lever action for fatigue-reduced operation
■ with length cutter and dismantling knife for ribbon cables 1/4“ and 1/2“ length
■ with additional stripping device for round cables
■ Chrome vanadium electric steel in special quality; oil-hardened
Product Number inch mm
Pliers Handles Capacity Number of crimping positions Ounces
97 51 10 7 1/2 190 burnished with multi-component gripsRJ 11/12 (6-poles) 3/8“ (9.65 mm) RJ 45 (8-poles) 15/32“ (11.68 mm)
2 12.0
97 59 06 4 spare blades for 97 51 04 / 97 51 10
97mounting Tool for mC3 connectors
97 49 65 2
■ for easy and quick assembly of MC3 solar cable connectors
■ for fit solar sleeves for connectors from 2.5 to 10.0 mm²
■ three capsules (2.5 / 4.0; 6.0; 10.0 mm²) for pulling on the sleeves, integrated in the detachable handle
■ body: plastic, fiberglass-rein-forced
The assembly tool comes with three torpedo capsules for the various cable cross-sections
Product Number inch mm
Capacitymm² Ounces
97 49 65 2 12 1/2 325 2.5 - 10.0 16.2
solaR Tool
crimPing Pliers
129
crimPing Pliers
9752 Crimping Pliers for two handed operation
97 52 06
97 52 09
■ the new lever transmission reduces the handforce up to 30% compared to regular crimping pliers
■ repetitive, high crimping quality due to precision dies and integral lock (self-releasing mechanism)
■ crimping pressure has been set precisely (calibrated) in the factory■ two hand operation for easy crimping of large conductor diameters ■ easy handling as a result of well balanced center of gravity, angled
head and ergnomically shaped handles ■ Chrome vanadium electric steel in special quality; oil-hardened
First step: move the handle with two fingers only until both jaws touch the connector to be crimped
Second step: now use the whole hand for further crimping procedure
Third step: when greater handforce is required, such as e.g. when crimping insulated connectors 6 mm2, two handed operation is possible with the longer handles
Product Number inch mm
Pliers Handles Applications Capacitymm²
AWG Number of crimping positions Ounces
97 52 05 10 250 burnished with non-slip plastic grips non-insulated, open spade plug-type connectors
0.5 - 6.0 10 - 20 3 20.0
97 52 06 10 250 burnished with non-slip plastic gripsinsulated terminals and plug connectors
0.5 - 6.0 10 - 20 3 20.0
97 52 09 10 250 burnished with non-slip plastic grips End Sleeves (ferrules) 10 / 16 / 25 3 / 5 / 7 3 20.1
97 52 13 10 250 burnished with non-slip plastic gripsnon-insulated terminals and plug connectors
0.5 - 10.0 7 - 20 4 19.7
97 52 19 10 250 burnished with non-slip plastic grips End Sleeves (ferrules) 35 - 50 0 + 2 2 20.0
97 52 23 10 250 burnished with non-slip plastic gripsnon-insulated terminals and plug connectors
16 + 25 3 + 5 2 20.0
97 49 94 Locator for 97 49 04 / 97 52 04 / 97 52 34
97 49 95 Locator for 97 49 05 / 97 52 05 / 97 52 35
130
crimPing Pliers
9752 Crimping Pliers short design
97 52 14
■ repetitive, high crimping quality due to precision dies and integral lock (self-releasing mechanism)
■ crimping pressure has been set precisely (calibrated) in the factory
■ optimum transmission of force due to lever action for fatigue-reduced operation
■ good handling due to 20° angled head, low weight and short design
■ Chrome vanadium electric steel in special quality; oil-hardened
97 52 14Available as accessory: locator for non-insulated open plug type connectors
Product Number inch mm
Pliers Handles Applications Capacitymm²
AWG Number of crimping positions Ounces
97 52 14 8 195 burnishedwith multi-component grips
non-insulated open spade plug type connectors (plug width 7/64“ + 3/16“ / 2.8 + 4.8 mm)
0.10 - 1.5 16 - 27 4 13.7
97 52 20 8 195
burnished
with multi-component grips
COAX-, BNC- and TNC-connectors RG 58 / 59 / 62 / 71 / 223
3 13.4
97 59 14 Locator for 97 52 14
9751 Crimping Pliers for Western plugs
97 51 12
■ professional tool for cutting and stripping unshielded ribbon telephone cables
■ for crimping 4-, 6- and 8-pole Western plugs type RJ 10 (19/64“ width), type RJ 11/12 (3/8“ width) and type RJ 45 (15/32“ width)
■ exact crimping process due to parallel crimping
■ repetitive, high crimping quality due to integral lock (self-releasing mechanism)
■ optimum transmission of force due to lever action for fatigue-reduced operation
■ with length cutter and dismantling knife for ribbon cables 1/4“ and 1/2“ length
Product Number inch mm
Pliers Handles Capacity Number of crimping positions Ounces
97 51 12 8 200 burnished with multi-component gripsRJ 10 (4-poles) 19/64“ (7.65 mm) RJ 11/12 (6-poles) 3/8“ (9.65 mm) RJ 45 (8-poles) 15/32“ (11.68 mm)
3 18.4
97 59 12 Spare blades for 97 51 12
■ with additional stripping device for round cables
■ Chrome vanadium electric steel in special quality; oil-hardened
131
crimPing Pliers
9752 KniPeX PreciForce® Crimping Pliers
97 52 34
97 52 36
For daily crimping applications, the specialist likes crimping pliers that work precisely and reliably. In addition, they should be light, comfortable to use, robust and reasonably priced – Meet the PreciForce®
■ repetitive, high crimping quality due to precision dies and integral lock (self-releasing mechanism)
■ crimping pressure has been set precisely (calibrated) in the factory ■ high transmission of force thanks to lever action for fatigue-reduced
work ■ good handling thanks to handle position, low weight, short design and
ergonomically shaped handles ■ Chrome vanadium electric steel in special quality; oil-hardened
97 52 36 97 52 37
Number of crimping positions
Product Number inch mm
Pliers Handles Applications Capacitymm²
AWG
Ounces
97 52 30 8 3/4 220 burnished with multi-component grips non-insulated butt connectors 1.5 - 4,0 6.0 + 10.0*
11 - 157 + 10
32
16.8
97 52 33 8 3/4 220 burnished with multi-component grips non-insulated terminals and plug connectors
0.5 - 10.0 7 - 20 4 16.9
97 52 34 8 3/4 220 burnished with multi-component gripsnon-insulated open spade plug type connectors (plug width 2.8 + 4.8 mm)
0.1 - 2.5 13 - 27 4 17.0
97 52 35 8 3/4 220 burnished with multi-component grips non-insulated open spade plug type connectors (plug width 4.8 + 6.3 mm)
0.5 - 6.0 10 - 20 3 17.4
97 52 36 8 3/4 220 burnished with multi-component gripsinsulated terminals and plug connectors
0.5 - 6.0 10 - 20 3 17.2
97 52 37 8 3/4 220 burnished with multi-component grips heat shrinkable sleeve connectors 0.5 - 6.0 10 - 20 3 16.9
97 52 50 8 3/4 220 burnished with multi-component grips COAX-, BNC- and TNC-connectors for RG 58 / 174 / 188 / 316
6 17.6
97 49 94 Locator for 97 49 04 / 97 52 04 / 97 52 34
97 49 95 Locator for 97 49 05 / 97 52 05 / 97 52 35
* compression joints in conformance to DIN 46267
Standard locator
132
crimPing Pliers
9752 Four-mandrel Crimping Pliers
for turned contacts
97 52 63 Dg
97 52 65
97 52 65 Dg
Turned contacts are used for demanding plug type connections, e.g. in the medical industry and aviation. Extremely reliable crimping connections can be achieved only with pliers that work with absolute precision and maintain the required crimping depth in the 1/100 mm range. KNIPEX has all of the tools you need to get these jobs done.
■ for crimping turned contacts ■ four-mandrel crimping for top-quality crimping connections ■ mandrel gauge to check the basic setting ■ repetitive, high crimping quality due to integral lock
(self-releasing mechanism) ■ optimum transmission of force due to lever action for
fatigue-reduced operation ■ high operation comfort thanks to ergonomic shape ■ Chrome vanadium electric steel in special quality; oil-hardened
97 52 63 Dgfine adjustment of pressure depending on the conductor‘s diameter by means of adjusting wheel; with digital display of the preset crimping capacities; display reversible between mm / inch and MIL numerical values; packaged in a plastic case with foam insert and locator for holding the contacts
97 52 65fine adjustment of pressure depending on the conductor‘s diameter by means of adjusting wheel; locator for positioning the contacts; with table for calculating the settings; packaged in a plastic case with foam insert
97 52 65 Dgfine adjustment of pressure depending on the conductor‘s diameter by means of adjusting wheel; with digital display of the preset crimping capacities; display reversible between mm / inch and MIL numerical values; with table for calculating the settings; packaged in a plastic case with foam insert and locator for holding the contacts
97 59 65 2Universal Locator for 97 52 65 / 97 52 65 A / 97 52 65 DG / 97 52 65 DG A; Chrome vanadium electric steel in special quality, oil-hardened■ locator that is universally adjustable (in length and diameter) for the repeatable
exact alignment of turned contacts in crimping pliers; can be set to all commercially available contacts in the four-mandrel crimping pliers‘ capacity range
97 59 65 2
Product Number inch mm
Pliers Handles Applications Capacitymm2
AWG Number of crimping positions Ounces
97 52 63 Dg 8 195 nickel plated with multi-component grips
turned contacts 0.08 - 2.5 13 - 28 1 13.7
97 52 65 9 230 nickel plated with multi-component grips
turned contacts (Harting; Ilme; Phoenix; Amphenol; Walther; HTS; Contact; Weidmüller)
0.14 - 6.0 10 - 25 1 23.8
97 52 65 Dg 10 250 nickel platedwith multi-component grips
turned contacts (Harting; Ilme; Phoenix; Amphenol; Walther; HTS; Contact; Weidmüller)
0.14 - 6.0 10 - 25 1 22.3
97 59 65 2 Universal Locator for 97 52 65 / 97 52 65 A / 97 52 65 DG / 97 52 65 DG A
133
crimPing Pliers
9753 self-adjusting Crimping Pliers for
end sleeves (ferrules) with lateral access
97 53 04
97 53 14
Small crimping pliers for wire-end ferrules with two great advantages for the user: - Automatic self-adjustment to the wire end ferrule used. This allows the specialist to work with less strain and enables secure, reliable and quick crimping. - Extensive range of applications: square crimping 0.08 to 10.0 mm²; hexagon crimping 0.08 to 6.0 mm²
■ for crimping end sleeves (ferrules) according to DIN 46228 parts 1 + 4 ■ self-adjusting adaptation to the desired wire end ferrule size:
no crimping faults caused by using the wrong die ■ lateral loading of the end sleeves (ferrules) into the tool ■ repetitive, high crimping quality due to integral lock
(self-releasing mechanism) ■ these tools have been set precisely (calibrated) in the factory ■ optimum transmission of force due to lever action for
fatigue-reduced operation ■ high operation comfort thanks to shape and low weight ■ Chrome vanadium electric steel in special quality; oil-hardened
97 53 04square crimping for optimum contact areas in the clamp connection
97 53 14heaxagonal crimping for optimum positioning in confined areas
The square crimping allows for better contact. The hexagonal crimping comes very close to the space-saving round shape. Compared to the square crimp, it has the same cross-section and can produce optimum contact in narrow, round terminal connectors. Both crimping shapes allow the user to easily feed into the terminal connection.
Square-crimped wire end ferrules always ensure good contact surfaces in the clamped connection
Product Number inch mm
Pliers Handles Applications Capacitymm²
AWG Number of crimping positions Ounces
97 53 04 7 1/4 180 burnished with multi-component grips End Sleeves (ferrules) 0.08 - 10.0 7 - 28 1 14.3
97 53 14 7 1/4 180 burnished with multi-component grips End Sleeves (ferrules) 0.08 - 6.0 10 - 28 1 14.3
134
crimPing Pliers
9753 self-adjusting Crimping Pliers for
end sleeves (ferrules) with front loading
97 53 08
97 53 09
The crimping pliers for wire end ferrules with three great advantages for the user: - Automatic self-adjustment to the wire end ferrule used. This allows the specialist to work with less strain and enables secure, reliable and quick crimping. - Range of applications also for large cross-sections: crimping 7 - 28 + 5 AWG - Front loading: very helpful under difficult working conditions in confined spaces
■ for crimping wire end ferrules ■ self-adjusting adaptation to the desired wire end ferrule size:
no crimping faults caused by using the wrong die ■ front loading of the wire end ferrules into the tool ■ repetitive, high crimping quality due to integral lock
(self-releasing mechanism) ■ crimping pressure has been set precisely (calibrated) in the factory,
readjustable■ optimum transmission of force due to toggle lever action for
fatigue-reduced operation ■ high operation comfort thanks to ergonomic shape and low weight ■ Chrome vanadium electric steel in special quality; oil-hardened
97 53 08Crimping from 7 to 28 AWG (0.08 - 10.0 mm²) in one profile; wire end ferrules up to 13 AWG (2.5 mm²) can also be loaded parallel from the side
97 53 09Crimping from 7 to 28 and 5 AWG (0.08 - 10.0 mm² and 16.0 mm²) in one profile; with selector lever for setting the crimping area either to 7 to 28 or 5 AWG (0.08 - 10.0 mm² or 16.0 mm²)
Front loading of wire end ferrules e.g. in switchboards
Square crimping
97 53 08: Lateral loading of wire end ferrules up to 13 AWG (2.5 mm²) parallel from the side e.g. in confined areas
Number of crimping positions
Product Number inch mm
Pliers Handles Applications Capacitymm²
AWG
Ounces
97 53 08 7 1/2 190 burnished with multi-component grips End Sleeves (ferrules) 0.08 - 10 7 - 28 1 16.8
97 53 09 7 1/2 190 burnished with multi-component grips End Sleeves (ferrules) 0.08 - 10 + 16 7 - 28 + 5 1 17.1
135
crimPing Pliers
976 Crimping Pliers for end sleeves
(ferrules)
97 62 145 a
97 68 145 a
■ for crimping wire end ferrules in an area of application from 13 - 23 AWG (0.25 up to 2.5 mm2)
■ crimping in marked trapezoidal dies for tight connections between the sleeve and the conductor
■ Vanadium electric steel; forged, oil-hardened
Number of crimping positions
Product Number inch mm
Head Handles Capacitymm²
AWG
Ounces
97 61 145 a 5 3/4 145 polished plastic coated 0.25 - 2.5 13 - 23 6 4.9
97 62 145 a 5 3/4 145 polished with multi-component grips 0.25 - 2.5 13 - 23 6 6.0
97 68 145 a 5 3/4 145
polished insulated with multi-component grips, VDE-tested 0.25 - 2.5 13 - 23 6 6.2
977 Crimping Pliers for end sleeves
(ferrules)
97 71 180
97 72 180
■ for crimping wire end ferrules from 5 to 23 AWG (0.25 up to 16 mm2)■ crimping in marked, half-round dies for tight connections between
the sleeve and the conductor ■ 9 extremely deep troughs with cone-shaped side faces ■ Special tool steel; forged, oil-hardened
Number of crimping positions
Product Number inch mm
Head Handles Applications Capacitymm²
AWG
Ounces
97 71 180 7 1/4 180 polished plastic coated End Sleeves (ferrules) 0.25 - 16 5 - 23 9 8.5
97 72 180 7 1/4 180 polished with multi-component grips End Sleeves (ferrules) 0.25 - 16 5 - 23 9 10.0
136
crimP Assortments
9791 Tool set for Photovoltaics
97 91 01
■ with tools for photovoltaics ■ without crimp dies – for individual equipment –
please order separately (see ref. 97 49 ..) ■ with service tools (Allen key) for changing crimp dies ■ shock-resistant plastic case ■ foam insert with recesses for tools, crimp dies and locators ■ external dimensions (W x H x D): 13 37/64 x 3 5/32 x 11“
external dimensions (W x H x D): 345 x 80 x 280 mm
Product Number
EAN4003773-
Units
Ounces
97 91 01
070351
Tool Case for Photovoltaics 69.3
12 12 11 Precision Insulation Stripper with shaped blades 1
95 16 165 Cable Shears 1
97 43 200 Crimp System Pliers 1
not included (please order separately):
97 49 62 063179 Crimping dies for solar cable connectors (Huber + Suhner)
97 49 63 066675 Crimping dies for solar cable connectors (Huber + Suhner)
97 49 65 066682 Crimping dies for solar cable connectors MC3 (Multi-Contact)
97 49 65 1 066729 Locator for 97 49 65 (solar cable connectors MC3)
97 49 65 2 072010 Mounting Tool for MC3 connectors
97 49 66 066699 Crimping dies for solar cable connectors MC4 (Multi-Contact)
97 49 66 1 066736 Locator for 97 49 66 (solar cable connectors MC4)
97 49 66 4 072096 Crimping dies for solar cable connectors MC4 (Multi-Contact) cutting - stripping - crimping
97 49 66 6 072102 Crimping dies for solar cable connectors MC4 (Multi-Contact) cutting - stripping - crimping
97 49 67 066705 Crimping dies for solar cable connectors SunCon (Hirschmann)
97 49 68 066712 Crimping dies for solar cable connectors Solarlok (Tyco)
97 49 68 1 066743 Locator for 97 49 68 solar cable connectors (Solarlok)
97 49 69 1 072119 Crimping dies for solar cable connectors gesis® PST 40 (Wieland)
97 49 69 2 072126 Crimping dies for solar cable connectors gesis® PST 40 (Wieland)
97 49 69 11 072133 Locator for 97 49 69 1 and 97 49 69 2
97 49 59 073734 Crimping dies for solar cable connectors Helios H4 (Amphenol)
137
crimP Assortments
9791 Tool Case for Photovoltaics, mC3
(multi-Contact)
97 91 02
■ the complete tool set to install MC3 connectors ■ with service tools (Allen key) for changing crimp dies ■ shock-resistant plastic case ■ foam insert with recesses for the tools, crimping dies and locators ■ with four empty plastic boxes for consumables for individual equipping ■ dimensions, exterior (W x H x D): 14 11/64 x 4 1/8 x 11 13/16“
dimensions, exterior (W x H x D): 360 x 105 x 300 mm
Product Number
EAN4003773-
Quantity
Ounces
97 91 02
074083
Tool Case for Photovoltaics, MC3 (Multi-Contact) 75.0
12 12 11 Precision Wire Stripper 1
95 16 165 Cable Shears 1
97 43 200 Crimp System Pliers 1
97 49 65 Crimping dies for solar cable connectors MC3 (Multi-Contact) 1
97 49 65 1 Locator for 97 49 65 (solar connectors MC3) 1
97 49 65 2 Mounting Tool for MC3 connectors 1
97 91 02 le 074090 Tool Case for Photovoltaics, MC3 (Multi-Contact) empty
138
cAble connectors
9799 Product
Number Designation Width x Thickness
mm²
PlugØ inch
PlugØ mm
ScrewsØ inch
ScrewsØ mm
Cablemm²
AWG Color Quantity
97 99 01 Female Spade Sockets 6.3 x 0.8 0.5 - 1.0 17 - 20 red 75
97 99 02 Female Spade Sockets 6.3 x 0.8 1.5 - 2.5 13 - 15 blue 5097 99 03 Female Spade Sockets 6.3 x 0.8 4.0 - 6.0 10 - 11 yellow 25 97 99 04 Female Spade Sockets 8.0 x 0.8 1.5 - 2.5 13 - 15 blue 5097 99 05 Male Spade Connectors 6.3 x 0.8 0.5 - 1.0 17 - 20 red 75 97 99 06 Male Spade Connectors 6.3 x 0.8 1.5 - 2.5 13 - 15 blue 7597 99 07 Round Sockets 0.5 - 1.0 17 - 20 red 25 97 99 08 Round Sockets 1.5 - 2.5 15 - 13 blue 2597 99 09 Round Pin Plugs 0.5 - 1.0 17 - 20 red 75 97 99 10 Round Pin Plugs 1.5 - 2.5 13 - 15 blue 5097 99 11 Insulated Double Spade Connector 6.3 x 0.8 0.5 - 1.0 17 - 20 red 25 97 99 12 Insulated Double Spade Connector 6.3 x 0.8 1.5 - 2.5 13 - 15 blue 2597 99 13 Cable Connectors, eye type 7/64 3.0 0.5 - 1.0 17 - 20 red 100 97 99 14 Cable Connectors, eye type 5/32 4.0 0.5 - 1.0 17 - 20 red 10097 99 15 Cable Connectors, eye type 13/64 5.0 0.5 - 1.0 17 - 20 red 100 97 99 16 Cable Connectors, eye type 5/32 4.0 1.5 - 2.5 13 - 15 blue 10097 99 17 Cable Connectors, eye type 13/64 5.0 1.5 - 2.5 13 - 15 blue 50 97 99 18 Cable Connectors, eye type 15/64 6.0 1.5 - 2.5 13 - 15 blue 5097 99 19 Cable Connectors, eye type 5/16 8.0 1.5 - 2.5 13 - 15 blue 50 97 99 20 Cable Connectors, eye type 13/64 5.0 4.0 - 6.0 10 - 11 yellow 2597 99 21 Cable Connectors, eye type 15/64 6.0 4.0 - 6.0 10 - 11 yellow 25 97 99 22 Cable Connectors, eye type 5/16 8.0 4.0 - 6.0 10 - 11 yellow 2597 99 23 Cable Connectors, eye type 25/64 10.0 4.0 - 6.0 10 - 11 yellow 25 97 99 24 Spade Connectors, forked 5/32 4.0 0.5 - 1.0 17 - 20 red 10097 99 25 Spade Connectors, forked 5/32 4.0 0.5 - 1.0 17 - 20 red 100 97 99 26 Spade Connectors, forked 13/64 5.0 0.5 - 1.0 17 - 20 red 7597 99 27 Spade Connectors, forked 5/32 4.0 1.5 - 2.5 13 - 15 blue 75 97 99 28 Spade Connectors, forked 13/64 5.0 1.5 - 2.5 13 - 15 blue 5097 99 29 Spade Connectors, forked 13/64 5.0 4.0 - 6.0 10 - 11 yellow 25 97 99 30 Spade Connectors, forked 15/64 6.0 4.0 - 6.0 10 - 11 yellow 2597 99 31 Pin Connectors 0.5 - 1.0 17 - 20 red 100 97 99 32 Pin Connectors 1.5 - 2.5 13 - 15 blue 10097 99 33 Pin Connectors 4.0 - 6.0 10 - 11 yellow 25 97 99 34 Insulated Butt Connectors 0.5 - 1.0 17 - 20 red 5097 99 35 Insulated Butt Connectors 1.5 - 2.5 13 - 15 blue 50 97 99 36 Insulated Butt Connectors 4.0 - 6.0 10 - 11 yellow 25
97 99 37 Two-Way-Sockets 6.3 - 0.8 25
97 99 38 Double spade connector 6.3 - 0.8 50
97 99 40 Wire End Ferrules 0.5 20 200 97 99 41 Wire End Ferrules 0.75 18 20097 99 42 Wire End Ferrules 1.0 17 200 97 99 43 Wire End Ferrules 1.5 15 20097 99 44 Wire End Ferrules 2.5 13 200 97 99 45 Wire End Ferrules 4.0 11 15097 99 46 Wire End Ferrules 6.0 10 150 97 99 47 Wire End Ferrules 10.0 7 5097 99 48 Wire End Ferrules 16.0 5 50 97 99 49 Wire End Ferrules 25.0 3 5097 99 70 Wire End Ferrules with collar 0.5 20 white 200 97 99 71 Wire End Ferrules with collar 0.75 18 grey 20097 99 72 Wire End Ferrules with collar 1.0 17 red 200 97 99 73 Wire End Ferrules with collar 1.5 15 black 20097 99 74 Wire End Ferrules with collar 2.5 13 blue 200 97 99 75 Wire End Ferrules with collar 4.0 11 grey 15097 99 76 Wire End Ferrules with collar 6.0 10 yellow 150 97 99 77 Wire End Ferrules with collar 10.0 7 red 5097 99 78 Wire End Ferrules with collar 16.0 5 blue 50 97 99 79 Wire End Ferrules with collar 25.0 3 yellow 5097 99 92 Non-insulated Female Spade Connectors 2.8 - 1.5 15 150 97 99 93 Non-insulated Female Spade Connectors 4.8 - 1.5 15 15097 99 95 Non-insulated Female Spade Connectors 6.3 - 1.5 15 100 97 99 96 Non-insulated Female Spade Connectors 6.3 - 2.5 13 100
139
vde Pliers HAndles:imProved design. more comfort.
distinctive vDe design
rounded collar edges reduce uncomfortable pressure points
recess in the collar to facilitate a precise and steady pliers guidance
durable injection-molded marking
optimized arrangement of the soft and hard components
yellow, softer material for a better grip when force is applied
red, harder material reduces friction when the grips need to move in the hand
140
insulAted toolsWork on electrical installations is subject to the special protection tasks of authorities and insurance companies. This resulted in the creation of diverse national and international safety standards (in the US NFPA 70 E, internationally IEC 60364). Only a qualified electrician who respects and follows these and maybe additional regulations is permitted to carry out work on electrical installations (including live working). He has to use special tools for this particular work that have been specifically made for this kind of work and have been thoroughly tested.
KNIPEX insulated tools are made of high-quality materials, which have been manufactured and tested in conformance with the regulations of national and international standards. If the prescribed method for working on electrical installations (see above) are observed, these tools offer the greatest possible protection even when it is necessary to work live up to AC 1000 V (alternating current) and DC 1500 V (direct current).
Since 1987 the IEC 60900 has specified worldwide requirements for tools for live working. For the US this standard has been adapted as ASTM F 1505. Tests on KNIPEX tools which bear the special mark
include subjecting them to routine tests with 10,000 volts to check their dielectric strength. This gives the user a considerable buffer of additional protection even if work on electrical installations needs to be performed live.
The mark identifies KNIPEX insulated tools as being suitable for live working. The specified standard also shows the re-quirements our claim can be measured against. The manufacturer name KNIPEX on the insulation indicates that we accept responsi-bility for the correctness of this information. The marks prove: The observation of these requirements is monitored not only by the KNIPEX quality assurance team but also e.g. by the independent VDE (Association of German Electricians).
Because the purchase of insulated hand tools is a matter of trust.
Type examination, manufacturing inspections and stock monitoring by the independent VDE testing center.
insulAtion by injection molded sleeves(version 6)
KNIPEX pliers with the two-color multi-component handle insulation meet the requirements of the international standard IEC 60900. This claim is confirmed by the VDE/GS mark, awarded by an prestigious independent neutral inspection body and of ASTM F 1505.
The slip guard is designed to prevent the hand from slipping unintentionally on conductive metal parts at the head of the pliers.
diPPed insulAtion(version 7)Other hand tools such as open-ended spanners/single-ended box wrenches, socket wrenches, ratchets etc. are insulated at KNIPEX using a plastic dipping method. These also meet all requirements of the international standards IEC 60900 and ASTM F 1505. To round off this range, KNIPEX also insulates pliers in a dipping process to adapt the-se tools concerning appearance and production method to the other dipped insulated tools. These pliers also bear the VDE/GS mark.
The firmly bonded extra thick dipped insulation is made of insulating material which is free of harmful substances.
Two layer insulation at the ends of the handles. This prevents cracks caused by an impact.
Insulated tools must be transported and stored in a manner that will prevent any damage to the insulation.Check before every use whether the insulation is damaged in any way, defective tools must be discarded.Always keep your insulated tools clean and dry.Wear protective goggles when working with cutting nippers or working overhead.Always wear goggles or a facial mask when working on, or close to live equipment.
Make sure the workplace is clean and orderly, particularly when you are working on live installations.Wear protective clothing and use additional safety equipment (e.g. insulating gloves, insulating mats, protective covers) especially in confined working spaces.Use only a tool with suitable dimensions. That will prevent slipping on the workpiece and unintentional contact with non-insulated parts.Make sure that detached parts or cut-off ends of conductors do not fall onto live parts.
■ ■
■ ■
■
■ ■
■
■
always comply with the currently valid regulations and observe the saFeTy insTRuCTions given below:
141
kniPeX insulAted tools – 100 % tested, one by one
Testing dielectric strength Testing the adhesion of the insulating coatingEach KNIPEX insulated tool has been tested individually. This individual testing is done with a test voltage of AC 10,000 volts. This test load, which is 10 times as high as the maximum permitted voltage during work, shows probable cause to the user to trust a reliable insulation when live working.
The adhesion of the insulating coating is tested after storage of 168 hours at 158°F / 70°C. In case of pliers a tensile load of 500 N is applied. The insulating material must remain firmly bonded to the basic tool.
Testing low temperature impact strength Testing burning behaviourThe tools are cooled down to -13°F / -25°C. The insulation material must retain the toughness necessary to ensure that it does not break when hit or knocked.
KNIPEX uses only flame-resistant and self-extinguishing plastics for insulation.
Testing electrical insulation Testing indentation resistanceAfter submersion in water for 24 hours, the tools are tested with AC 10,000 V for 3 minutes including measuring of the leakage current. The reading of the leakage current must stay below the limits defined in the standards.
The insulation heated to 158°F / 70°C must prove under standardized test conditions that the warm plastic has sufficient mechanical strength to resist expected loads.
142
insulAted tools
02high leverage Combination Pliers ISO 5746 IEC 60900 ASTM F1505
02 08 200 sba
02 08 225 sba
■ 35% less effort required compared to conventional combination pliers ■ easier work due to high leverage design■ with cutting edges (hardness approx. 63 HRC) for soft, hard, piano
and ACSR wire■ long cutting edges for thicker cables ■ with gripping zones for flat and round material, suitable for
versatile use ■ High-grade special tool steel; forged, oil-hardened
03Combination Pliers ISO 5746 IEC 60900 ASTM F1505
■ with gripping zones for flat and round material, suitable for versatile use
■ with cutting edges for soft and hard wire ■ long cutting edges for thicker cables ■ cutting edge hardness approx. 60 HRC■ Special tool steel; forged, oil-hardened
03 08 160 sba
03 08 180 sba
03 08 200 sba
Cutting capacitiesProduct Number inch mm
Pliers Head Handles
Ø inch Ø inch Ø inch AWG Ø mm Ø mm Ø mm mm² Ounces
02 08 200 sba 8 200 black atramentized
polished insulated with multi-component grips, VDE-tested
7/64 3/32 1/2 3 2.8 2.2 13.0 25.0 12.1
02 08 225 sba 9 225 1/8 3/32 35/64 3 3.0 2.5 14.0 25.0 14.4
Cutting capacitiesProduct Number inch mm
Pliers Head Handles
Ø inch Ø inch Ø inch AWG Ø mm Ø mm Ø mm mm² Ounces
03 08 160 sba 6 1/4 160 black atramentized
polishedinsulated with multi-component grips, VDE-tested
1/8 5/64 25/64 5 3.1 2.0 10.0 16.0 7.9
03 08 180 sba 7 1/4 180 9/64 3/32 15/32 5 3.4 2.2 12.0 16.0 9.0
03 08 200 sba 8 200 5/32 3/32 33/64 5 3.8 2.5 13.0 16.0 11.4
143
insulAted tools
09lineman‘s Pliers new england style
ISO 5746 ASME B107.20 IEC 60900 ASTM F1505
■ heavy duty■ high transmission ratio for easy cutting ■ high leverage design requires 40% less effort compared to
conventional combination pliers ■ effective cross-hatched knurled gripping zone in the jaws -
for strong gripping and pulling ■ additional serrated gripping zone below the articulated joint
for powerful leverage■ with cutting edges for soft, hard and ACSR wire■ cutting edge hardness approx. 64 HRC ■ Vanadium electric steel; forged, oil-hardened09 08 240
11insulation strippersIEC 60900 ASTM F1505
11 08 160 sba
■ for single, multiple and fine stranded conductors with plastic or rubber insulation of a maximum 13/64“ diameter. Also suitable for 7 AWG wire.
■ easy adjustment to the required diameter of solid or stranded wire with knurled screw and lock nut
■ Special tool steel; forged, oil-hardened
13■ multifunctional pliers for the electrical installation; for cutting cable,
stripping and crimping end sleeves (ferrules), to grip flat and round material, for bending, deburring,
■ 6 functions in one pair of pliers ■ smooth surfaces near the tips grip single conductors without damaging
them; serrated gripping surfaces and pipe grip for gripping flat and round material
■ clear-cut outside edge on the jaw for working on flush-mounted junction boxes and deburring feed-through holes
■ stripping holes for 12 + 14 AWG■ crimp die for end sleeves (ferrules) 12 - 20 AWG ■ cable shears with (induction-hardened) precision cutting edges for
copper and aluminium cables up to 19/32“ dia. ■ slim dimensions for easy access ■ bolted joint: precise, zero backlash operation of pliers ■ High-grade special tool steel; forged, oil-hardened
installation PliersASTM F1505
13 88 8
Cutting capacitiesProduct Number inch mm
Pliers Head Handles
Ø inch Ø inch Ø mm Ø mm Ounces
09 08 240 9 1/2 240 black atramentized polishedinsulated with multi-component grips, VDE-tested
3/16 1/8 4.6 3.0 16.6
Stripping capacitiesProduct Number
inch mm
Pliers Head Handles Ø inch Ø mm mm² AWG
Ounces
11 08 160 sba 6 1/4 160 black atramentized polishedinsulated with multi-component grips, VDE-tested
13/64 5.0 10.0 7 5.9
Stripping capacity for cross-sections Crimping capacityProduct Number inch mm
Pliers Head Handles AWG mm² AWG mm²
Ounces
13 88 8 8 200
black atramentized
polished insulated with multi-com-ponent grips, VDE-tested
12 + 14 0.7 - 1.5 + 2.5 12 - 20 0.5 - 2.5 9.9
144
insulAted tools
20Flat nose Pliers ISO 5745 IEC 60900 ASTM F1505
■ flat, short and wide jaws ■ serrated gripping surfaces ■ Chrome vanadium electric steel; forged, oil-hardened
22Round nose Pliers ISO 5745 IEC 60900 ASTM F1505
■ for bending wire loops ■ round, short jaws; smooth ground ■ Chrome vanadium electric steel; forged, oil-hardened
22 08 160 sba
30 long nose Pliers ISO 5745 IEC 60900 ASTM F1505
■ heavy duty gripping pliers ■ different jaw styles for a wide range of applications■ Chrome vanadium electric steel; forged, oil-hardened
style 3long, round jaws; smooth gripping surfaces
30 36 160
DimensionsProduct Number inch mm
Head Handles L3inch
W3inch
T1inch
L3mm
W3mm
T1mm Ounces
20 06 160 6 1/4 160 chrome platedinsulated with multi-component grips, VDE-tested 1 3/16 43/64 3/8 30.0 17.0 9.5 5.1
20 06 160
DimensionsProduct Number inch mm
Style Pliers Handles L3inch
W3inch
T1inch
W4inch
T2inch
L3mm
W3mm
T1mm
W4mm
T2mm Ounces
30 16 160 6 1/4 160 1 chrome platedinsulated with multi-component grips, VDE-tested
1 3/32 21/32 3/8 1/8 3/32 50.0 16.5 9.5 3.0 2.5 5.3
30 36 160 6 1/4 160 3 chrome platedinsulated with multi-component grips, VDE-tested
1 19/32 21/32 3/8 13/64 3/32 41.0 16.5 9.5 5.0 2.5 5.0
DimensionsProduct Number inch mm
Pliers Head Handles L3inch
W3inch
D1inch
T1inch
L3mm
W3mm
D1mm
T1mm Ounces
22 08 160 sba 7 1/4 160
black atramentized
polishedinsulated with multi-com-ponent grips, VDE-tested
1 3/16 23/32 1/8 3/8 30.0 18.0 3.0 9.5 6.0
145
insulAted tools
25 snipe nose side Cutting Pliers (radio pliers)
ISO 5745 IEC 60900 ASTM F1505
■ suitable for fine gripping and cutting work ■ pointed, half-round jaws ■ serrated gripping surfaces ■ with cutting edges for soft, medium and hard wire ■ cutting edges additionally induction hardened,
cutting edge hardness approx. 61 HRC ■ Vanadium electric steel; forged, oil-hardened
25 08 160 sba
26snipe nose side Cutting Pliers (stork beak pliers)
ISO 5745 IEC 60900 ASTM F1505
■ resilient precision tips snap back into place even after being twisted■ half-round, long, pointed jaws ■ with additionally hardened cutting edges (hardness approx. 61 HRC)
for soft, medium hard and hard wire ■ Vanadium electric steel; forged, oil-hardened
elastic tips: stable even when twisted
Cutting capacities DimensionsProduct Number inch
Pliers Head Handles
Ø inch Ø inch
L3inch
L4inch
T1inch
W3inch
W4inch
T2inch Ounces
26 18 200 sba 8
black atramentized
polishedinsulated with multi-com-ponent grips, VDE-tested
1/8 3/32 2 7/8 3/8 11/16 1/8 3/32 6.0
26 28 200 sba 840°
black atramentized
polishedinsulated with multi-com-ponent grips, VDE-tested
1/8 3/32 2 7/8 29/32 3/8 11/16 1/8 3/32 6.0
Cutting capacities DimensionsProduct Number mm
Pliers Head Handles
Ø mm Ø mm
L3mm
L4mm
T1mm
W3mm
W4mm
T2mm Ounces
26 18 200 sba 200
black atramentized
polishedinsulated with multi-com-ponent grips, VDE-tested
3.2 2.2 73.0 9.5 17.5 3.0 2.5 6.0
26 28 200 sba 20040°
black atramentized
polishedinsulated with multi-com-ponent grips, VDE-tested
3.2 2.2 73.0 23.0 9.5 17.5 3.0 2.5 6.0
26 18 200 sba
Cutting capacities DimensionsProduct Number inch
Pliers Head Handles
Ø inch Ø inch
L3inch
W3inch
T1inch
W4inch
T2inch Ounces
25 08 160 sba 6 1/4 black atramentized
polishedinsulated with multi-com-ponent grips, VDE-tested
3/32 1/16 1 31/32 21/32 23/64 1/8 3/32 5.1
Cutting capacities DimensionsProduct Number mm
Pliers Head Handles
Ø mm Ø mm
L3mm
W3mm
T1mm
W4mm
T2mm Ounces
25 08 160 sba 160 black atramentized
polishedinsulated with multi-com-ponent grips, VDE-tested
2.5 1.6 50.0 16.5 9.0 3.0 2.5 5.1
146
insulAted tools
70Diagonal Cutters ISO 5749 IEC 60900 ASTM F1505
70 08 160 sba
74 08 200 sba
70 08 180 sba
74 08 250 sba
■ the essential cutting tool for versatile use ■ high quality material and precise workmanship for long service life ■ precision cutting edges (cutting edge hardness approx. 62 HRC)
for soft and hard wire ■ clean cutting of thin copper wires, also at the cutting edge tips ■ narrow head style for use in confined areas ■ Vanadium electric steel; forged, oil-hardened
Slim head style and precise cut at blade tips: Advantageous when working in confined areas.
20% reduction in required forcecompared to conventional diagonal cutters of the same length. With forged-on joint axle.
74high leverage Diagonal Cutters
■ for very tough, continuous use ■ high cutting performance with minimum effort due to optimum
coordination of the cutting edge angle, transmission ratio and ergonomic handle shape
■ precision cutting edges (cutting edge hardness approx. 64 HRC) cut several types of wire including piano wire
■ Chrome vanadium heavy duty steel; forged, oil-hardened
ISO 5749 IEC 60900 ASTM F1505
Cutting capacitiesProduct Number inch mm
Pliers Head Handles
Ø inch Ø inch Ø inch Ø mm Ø mm Ø mm Ounces
70 08 160 sba 6 1/4 160
black atramentized
polishedinsulated with multi-component grips, VDE-tested
5/32 7/64 5/64 4.0 2.8 2.0 6.0
70 08 180 sba 7 1/4 180 5/32 1/8 3/32 4.0 3.0 2.5 7.1
Cutting capacitiesProduct Number inch mm
Style Pliers Head Handles
Ø inch Ø inch Ø inch Ø mm Ø mm Ø mm Ounces
74 08 200 sba 8 200
0
black atramentized
polishedinsulated with multi-component grips, VDE-tested
11/64 1/8 3/32 4.2 3.0 2.5 10.7
74 08 250 sba 10 250 3/16 9/64 1/8 4.6 3.5 3.0 15.4
147
insulAted tools
8607 Pliers Wrench
IEC 60900 ASTM F1505
86 07 250 sba
73KniPeX X-Cut ISO 5749 IEC 60900 ASTM F1505
73 06 160
■ box-joint design: highest stability at low weight ■ dual supported joint axis for heavy duty cutting■ high cutting capacity with very little effort due to the optimum
coordination of cutting edge angle and lever ratio with off center pivot point
■ 40% less effort required compared to diagonal cutters of the same length
■ large opening width for thicker cables■ cuts all wires precisely, even fine copper wires■ compact, low weight construction■ universally usable in assembly, maintenance and production■ Chrome vanadium heavy duty steel; forged, oil-hardened
Product Number mm
Pliers Handles
Ø mm Ø mm Ø mm Ø mm
Ø mm Ounces
73 06 160 160 chrome plated insulated with multi-component grips, VDE-tested 4.8 3.8 2.7 2.2 12.0 6.9
Product Number inch
Pliers Handles
Ø inch Ø inch Ø inch Ø inch
Ø inch Ounces
73 06 160 6 1/4 chrome plated insulated with multi-component grips, VDE-tested 3/16 5/32 7/64 3/32 30/64 6.9
■ replaces a full set of inch and metric open end wrenches■ adjustable tightening tool ■ excellent for gripping, holding, pressing and bending applications ■ smooth jaws for careful installation of plated fittings ■ will not round off nuts and bolts and won‘t damage chrome
and other soft finishes ■ parallel jaws allow infinitely variable gripping of all widths
to the specified maximum size ■ reliable catching of the hinge bolt: no unintentional shifting ■ the action of the jaws allows bolted connections to be tightened
and released quickly using the ratchet principle ■ lever transmission greater than 10 - 1 for strong gripping power ■ Chrome vanadium electric steel; forged, oil-hardened
DimensionsProduct Number inch mm
Pliers Handles
inch mm
Adjustment positions
B1inch
B2inch
B3inch
B1mm
B2mm
B3mm Ounces
86 07 250 sba 10 250
chrome plated
with dipped insulation grips, VDE-tested
1 3/4 46 17 5/16 5/16 35/64 8.0 8.0 14.0 21.7
148
insulAted tools
8728 KniPeX Cobra® vDe
hightech Water Pump Pliers
ISO 5749 IEC 60900 ASTM F1505
87 28 250 sba
It‘s easy to achieve the perfect capacity on the KNIPEX Cobra® VDE Pliers. You don‘t even have to push the button! Simply place the upper gripping jaw of the pliers on the work piece and slide the upper handle forward.
■ adjustment by shifting the jaw directly on to the workpiece: fast, reliable and comfortable handle width
■ opening at the touch of a button off the workpiece
■ fine adjustment for optimum adaptation to different workpiece sizes and a comfortable gripping position
■ good access to the workpiece due to slim size in the head and joint area
Quick adjustment to the workpiece without using the push-button, hands stay behind guard Just push the pliers handle to adjust
■ self-locking on pipes and nuts: no slipping on the workpiece and low handforce required
■ gripping surfaces with special hardened teeth, teeth hardness approx. 61 HRC: low wear and reliable gripping
■ box-joint design: high stability because of double guide
■ pinch guard prevents operators‘ fingers being pinched
■ Chrome vanadium electric steel; forged, oil-hardened
88KniPeX alligator® Water Pump Pliers
ISO 5749 IEC 60900 ASTM F1505
88 08 250 sba
■ box-joint design: high stability because of double guide
■ self-locking on pipes and nuts: no slipping on the workpiece and low handforce required
■ pinch guard prevents operators' fingers from being pinched
■ favorable lever action: optimum transmission of force
■ gripping surfaces with special hardened teeth, teeth hardness approx. 61 HRC: low wear and reliable gripping
■ Chrome vanadium electric steel, forged, oil-hardened
Product Number inch mm
Pliers Head Handles
Ø inch Ø mm inch mm
Adjustment positions Ounces
87 28 250 sba 10 250
grey atramentized
polishedinsulated with multi-component grips, VDE-tested
2 50.0 1 3/4 46.0 24 12.0
Product Number inch mm
Pliers Head Handles
Ø inch inch Ø mm mm
Adjustment positions Ounces
88 08 250 sba 10 250
black atramentized
polishedinsulated with multi-component grips, VDE-tested
2 1 3/4 50.0 46.0 9 13.7
149
insulAted tools
950 Cable shears
IEC 60900 ASTM F1505
95 06 230
951 Cable shears
IEC 60900 ASTM F1505
Cut performed with a Diagonal Cutter: high effort required, inaccurate cut, considerable deforming and crushing of the cable
Cut effected with a Cable Shear: easy, clean cut without any deformation of the cable
95 18 165 sba
■ insulated and tested according to IEC 60900 / ASTM F 1505■ not suitable for ACSR, steel wire and hard drawn copper conductors ■ precision ground, hardened blades ■ no crushing, only slight deformation of the cable ■ with pinch guard and slip guard ■ adjustable bolted joint ■ shears body: Surgical steel; stainless, air-hardened ■ handles: plastic, impact-resistant
95 06 230for copper conductors single wire up to 16 mm2, multiple wire up to 1/0 AWG, fine- stranded up to 70 mm2 and aluminium conductors multiple wire up to 70 mm2; easy cutting with one handed operation due to high transmission ratio; stainless – surgical steel, oil-hardened and tempered
Cutting capacitiesProduct Number inch mm
Head Handles
Ø inch Ø mm mm²
AWG
Ounces
95 06 230 9 1/4 230 polished plastic insulated, VDE-tested 5/8 16.0 50 1/0 9.7
■ for cutting copper and aluminium cables, single and multiple wire ■ not suitable for ACSR, steel wire and hard drawn copper conductors ■ precision ground, hardened blades ■ clean and smooth cut without crushing and deformation ■ easy cutting with one handed operation ■ with pinch-guard and slip-guard ■ adjustable bolted joint, self-locking screw■ High-grade special tool steel, forged, oil-hardened
Cutting capacitiesProduct Number inch mm
Style Tool Handles
Ø inch Ø mm mm²
AWG
Ounces
95 18 165 sba 6 1/4 165 1 burnished insulated with multi-component grips, VDE-tested
19/32 15.0 50 1/0 8.8
150
insulAted tools
951 Cable shears with twin cutting edge
IEC 60900 ASTM F1505
■ for cutting copper and aluminium cables ■ not suitable for ACSR, steel wire and hard drawn copper conductors ■ precision ground, hardened blades ■ clean and smooth cut without crushing and deformation ■ by dividing the cutting actions into initial cut (insulating sheath in the
front cutting area) and final cut (conductor in the back cutting area), cables up to Ø 51/64“ can be cut in one handed operation
■ less effort required due to favorable lever ratio and optimized cutting edge geometry
■ with pinch guard and slip guard■ adjustable screw joint, self-locking ■ High-grade special tool steel; forged, oil-hardened
Final cut: After cutting the sheath in the front profile, the cut is finished through the metal partof the cable in the rear profile. Initial cut in the front profile, final cut in the rear profile – to keep it as easy as possible.
initial cut: Using the front cutting edge to cut the insulating sheath on larger cable diameters leaves an ergonomic handle opening width.
95 18 200 sba
951 Cable shears
IEC 60900 ASTM F1505
95 17 500
Large cutting capacity: max. 1“ dia./150 mm²
■ for cutting copper and aluminium cables, single and multiple wire
■ not suitable for ACSR, steel wire and wire ropes
■ precision ground, hardened blades
■ clean and smooth cut without crushing and deformation
■ low handforce required due to favorable lever ratio and new blade geometry
■ short design, length only 20“ ■ low weight ■ with pinch guard ■ adjustable bolted joint ■ cutter head: Vanadium electric
steel; forged, oil-hardened ■ handle shank: aluminium tube,
high-strength
Cutting capacitiesProduct Number inch mm
Head Handles
Ø inch Ø mm mm²
AWG
Ounces
95 17 500 20 500 polished plastic dipped insulated, VDE-tested 1 27.0 150 5/0 52.1
Cutting capacitiesProduct Number inch mm
Tool Handles
Ø inch Ø mm mm²
AWG
Ounces
95 18 200 sba 8 200 burnishedinsulated with multi-component grips, VDE-tested
51/64 20.0 70 2/0 12.0
151
953 Cable Cutters ratchet action
IEC 60900 ASTM F1505
95 36 280
■ for cutting copper and aluminium cables, single and multiple wire ■ not suitable for ACSR, steel wire and wire ropes ■ precision ground, hardened blades ■ clean and smooth cut without crushing and deformation ■ one handed operation using ratchet principle ■ little handforce required due to very high transmission ratio ■ two-stage ratchet drive for easy cutting ■ simple handling as a result of light weight and compact design –
can be used even in confined areas ■ with pinch guard and slip guard■ High-grade special tool steel; forged, oil-hardened
95 36 280suitable for aluminium sector cable up to 4 x 300 MCM (4 x 150 mm²)
insulAted tools
Cutting capacitiesProduct Number inch mm
Tool Handles
Ø inch Ø mm mm²
MCM
Ounces
95 36 320 12 1/2 320 black atramentized
insulated with multi-component grips, VDE-tested
2 23/64 60.0 600 1200 28.2
95 39 280 Movable spare blade for 95 31 280 / 95 36 280
953 Cable Cutters (ratchet action)
sturdy. easy to use. stable. innovative ratchet-drive. For cable up to 2 23/64 in diameter.
95 36 320
■ easy handling due to low weight (28.2 oz.) and compact construction (12 1/2“ length) – usable in confined areas also
■ cutting through copper and aluminium cables with diameters of up to 2 23/64 in (60 mm) in one handed and two handed
■ hardened cutting edges, precisely ground, cut smoothly and neatly without crushing
■ for cutting copper and aluminium single conductors as well as multiple stranded cables
■ not suitable for cutting ACSR, steel wire and wire ropes■ innovative three-stage ratchet-drive with high leverage for easy cutting
in one-hand and two-hand operation■ with one handed and two handed■ fixed handle with support area for putting down the pliers when cutting■ High-grade special tool steel, forged, oil-hardened
Cutting capacitiesProduct Number inch mm
Tool Handles
Ø inch Ø mm mm²
MCM
Ounces
95 36 250 10 250 black lacqueredinsulated with multi-component grips, VDE-tested
1 1/4 32.0 240 500 23.0
95 36 280 11 280 black lacquered insulated with multi-component grips, VDE-tested
2 52.0 380 750 29.5
95 39 280 Movable spare blade for 95 31 280 / 95 36 280
152
9768 Crimping Pliers for end sleeves
(ferrules) IEC 60900 ASTM F1505
97 68 145 a
■ for crimping wire end ferrules in an area of application from 13 - 23 AWG (0.25 up to 2.5 mm2)
■ crimping in marked trapezoidal dies for tight connections between the sleeve and the conductor
■ Vanadium electric steel; forged, oil-hardened
insulAted tools
957 Wire Rope and Cable Cutter
IEC 60900 ASTM F1505
95 77 600
■ for ACSR, wire ropes and steel rods, copper and aluminium cables
■ angular cutting blades prevent fanning out
■ optimum transmission ratio for high cutting performance
■ bolted cutter head; replaceable ■ lightweight ■ cutter head: High-grade special tool steel; oil-hardened ■ handles: Aluminium,
high-strength, drop forged
Cutting capacitiesProduct Number inch
Head Handles
inch Ø inch Ø inch
AWG
Ounces
95 77 600 23 1/2 polished plastic dipped insulated 5 29/32 35/64 23/64 5/0 83.2
Product Number mm
Head Handles
mm² Ø mm Ø mm
AWG
Ounces
95 77 600 600 polished plastic dipped insulated 150 14.0 9.0 5/0 83.2
95 79 600 Spare cutter head for 95 77 600
Number of crimping positions
Product Number inch mm
Head Handles Capacitymm²
AWG
Ounces
97 68 145 a 5 3/4 145
polished insulated with multi-component grips, VDE-tested 0.25 - 2.5 13 - 23 6 6.2
153
insulAted tools
980 open end Wrenches
IEC 60900 ASTM F1505
98 00 7/16
■ jaw 15° angled ■ basic tool chrome plated ■ Chrome vanadium steel; forged, oil-hardened
Product Number
Width across flats Sinch
Length l max. inch
Head width b max. inch
Head thickness a max. inch Ounces
98 00 7/16“
7/16 4 3/4 1 3/16 23/64 1.9
98 00 1 1/16“ 1 1/16 8 1/2 2 1/2 23/64 14.1
980 box Wrenches
IEC 60900 ASTM F1505
■ cranked ■ basic tool chrome plated ■ Chrome vanadium steel; forged, oil-hardened
Width across flats S Length l max. Head width b max. Head thickness a max. Product Number
inch inch mm inch mm inch mm
Ounces
98 01 1 1/16"
1 1/16 10 7/16 265.0 1 1/2 38.0 5/8 16.0 14.1
98 01 1/2“ 1/2 7 9/32 185.0 55/64 21.5 7/16 11.0 6.0
98 01 1/16“ 1 1/16 8 5/64 205.0 1 1/16 27.0 1/2 13.0 7.1
98 01 3/4“ 3/4 8 55/64 225.0 1 3/16 30.0 35/64 14.0 8.7
98 01 3/8“ 3/8 6 19/64 160.0 43/64 17.0 23/64 9.0 3.5
98 01 5/16“ 5/16 6 7/64 155.0 35/64 14.0 9/32 7.0 2.5
98 01 5/8“ 5/8 7 7/8 200.0 1 1/64 26.0 15/32 12.0 6.8
98 01 7/16“ 7/16 6 1/2 165.0 47/64 18.5 25/64 10.0 4.2
98 01 7/8“ 7/8 8 55/64 225.0 1 3/8 35.0 19/32 15.0 10.9
98 01 9/16“ 9/16 7 11/16 195.0 29/32 23.0 15/32 12.0 3.6
98 01 14
154
insulAted tools
980 nut Drivers with screwdriver handle
IEC 60900 ASTM F1505
98 03 10
■ ergonomically optimized dual component handle for fatigue-reduced work and optimum transmission of force
■ handle design prevents rolling ■ Chrome vanadium molybdenum steel
Width across flats S Blade length Handle length Head dia. Product Number inch
tip Handle inch inch inch inch
Ounces
98 03 04 9 1/4
burnishedinsulating multi-component handle, VDE-tested
5/32 5 4 7/32 23/64 2.5
98 03 05 9 1/4 13/64 5 4 7/32 25/64 2.5
98 03 08 9 1/4 5/16 5 4 13/32 19/32 4.4
98 03 10 9 1/4 25/64 5 4 13/32 43/64 4.2
Width across flats S Blade length Handle length Head dia. Product Number mm
tip Handle mm mm mm mm
Ounces
98 03 04 230
burnishedinsulating multi-component handle, VDE-tested
4.0 125.0 107.0 9.0 2.5
98 03 05 230 5.0 125.0 107.0 10.0 2.5
98 03 08 237 8.0 125.0 112.0 15.0 4.4
98 03 10 237 10.0 125.0 112.0 17.0 4.2
Sd
Sd
980 nut Drivers with T-handle
IEC 60900 ASTM F1505
98 05 13
■ Special tool steel; oil-hardened
Width across flats S Handle length max. Head dia.Product Number inch
inch inch inch
Ounces
98 04 08 8
5/16 3 35/64 19/32 12.1
98 04 17 8 43/64 6 7/64 1 1/8 15.0
98 04 19 8 3/4 6 7/64 1 7/32 18.5
98 05 13 12
33/64 6 7/64 15/16 14.4
98 05 17 12 43/64 6 7/64 1 1/8 19.2
98 05 19 12 3/4 6 7/64 1 7/32 23.8
Width across flats S Handle length max. Head dia.Product Number mm
mm mm mm
Ounces
98 04 08 200
8.0 90.0 15.0 12.1
98 04 17 200 17.0 155.0 28.5 15.0
98 04 19 200 19.0 155.0 31.0 18.5
98 05 13 300
13.0 155.0 23.5 14.4
98 05 17 300 17.0 155.0 28.5 19.2
98 05 19 300 19.0 155.0 31.0 23.8
155
insulAted tools
9807 adjustable Wrench
IEC 60900
98 07 250
22°
■ parallel smooth gripping jaws ■ variable gripping width ■ with scaling for pre-setting the width apart from the workpiece ■ with slip guard ■ Chrome vanadium steel
Product Number inch
Tool Handle
inch
Jaw widthinch
Head width inch
Width inch
Depth inch Ounces
98 07 250 10 22° chrome plated plastic dipped insulated 1 3/16 5/16 5/8 2 7/8 51/64 17.6
Product Number mm
Tool Handle
mm
Jaw widthmm
Head width mm
Width mm
Depth mm Ounces
98 07 250 260 22° chrome plated plastic dipped insulated 30 8.0 16.0 73.0 20.0 17.6
981 screwdrivers for
hexagon socket screws with T-handle
IEC 60900 ASTM F1505
98 15 08
■ Special tool steel; oil-hardened
Product Number inch
Width across flats Sinch
Length of non-insulated blade ± 5/64 inch
T-Handle length inch Ounces
98 14 05 4 3/4
13/64 23/64 3 35/64 7.8
98 14 06 4 3/4 15/64 25/64 3 35/64 7.3
98 14 08 4 3/4 5/16 7/16 3 35/64 10.1
98 15 05 10
13/64 23/64 3 35/64 12.8
98 15 06 10 15/64 25/64 3 35/64 15.9
98 15 08 10 5/16 7/16 3 35/64 12.7
Product Number inch
Width across flats Smm
Length of non-insulated blade ± 2 mm
T-Handle lengthmm Ounces
98 14 05 120
5.0 9.0 90.0 7.8
98 14 06 120 6.0 10.0 90.0 7.3
98 14 08 120 8.0 11.0 90.0 10.1
98 15 05 250
5.0 9.0 90.0 12.8
98 15 06 250 6.0 10.0 90.0 15.9
98 15 08 250 8.0 11.0 90.0 12.7
S
156
insulAted tools
98T-handle with driving square 3/8“ or 1/2“
IEC 60900 ASTM F1505
98 40
■ for use with sockets ■ quick, easy and reliable locking of attached sockets ■ chrome plated ■ High-grade special tool steel; forged, oil-hardened
Handle length Square driveProduct Number inch mm
inch mm inch
Ounces
98 30 8 200 6 1/2 165 3/8 15.8
98 40 8 200 6 1/2 165 1/2 22.3
98Reversible Ratchetswith driving square 3/8“ or 1/2“
IEC 60900 ASTM F1505
98 31
■ for use with sockets ■ reversible for clockwise and counter-clockwise directions ■ extremely smooth action ■ quick, easy and reliable locking of attached sockets ■ Chrome vanadium steel; forged
Square driveProduct Number inch mm
Inch
Ounces
98 31 7 1/2 190 3/8 11.4
98 41 10 1/2 265 1/2 22.0
98extension bars with male and female driving square 3/8“ or 1/2“
IEC 60900 ASTM F1505
98 35 125
98 45 250
■ for use with sockets ■ with internal and external square ■ quick, easy and reliable locking of attached sockets ■ Chrome vanadium steel; forged
Product Number inch mm
Square drive inch Ounces
98 35 125 5 125
3/8 5.3
98 35 250 10 250 3/8 10.4
98 45 125 5 125
1/2 9.1
98 45 250 10 250 1/2 17.3
157
insulAted tools
98hexagon sockets for hexagon screws driving square 3/8“ or 1/2“
IEC 60900 ASTM F1505
98 37 17
■ for metric and imperial hexagonal head screws ■ chrome plated ■ Chrome vanadium steel
Width across flats S Diameter of effective tool side d max. Square driveProduct Number
inch mm inch mm inch
Ounces
98 37 10
25/64 10.0 47/64 18.7 3/8 1.1
98 37 11 7/16 11.0 51/64 20.0 3/8 1.1
98 37 12 15/32 12.0 53/64 21.2 3/8 1.2
98 37 13 1/2 13.0 57/64 22.5 3/8 1.2
98 37 14 35/64 14.0 15/16 23.7 3/8 1.4
98 37 16 5/8 16.0 1 1/32 26.2 3/8 1.9
98 37 17 43/64 17.0 1 5/64 27.5 3/8 2.2
98 37 19 3/4 19.0 1 3/16 30.0 3/8 2.6
98 37 5/16“ 5/16 41/64 16.2 3/8 1.1
98 37 3/8“ 3/8 47/64 18.7 3/8 1.1
98 37 7/16“ 7/16 51/64 20.0 3/8 1.1
98 37 1/2“ 1/2 57/64 22.5 3/8 1.2
98 37 9/16“ 9/16 15/16 23.7 3/8 1.4
98 37 5/8“ 5/8 1 1/32 26.2 3/8 1.8
98 37 3/4“ 3/4 1 3/16 30.0 3/8 2.5
98 37 1/4“ 1/4 37/64 14.7 3/8 1.1
98 47 10
25/64 10.0 49/64 19.5 1/2 2.2
98 47 11 7/16 11.0 13/16 20.7 1/2 2.2
98 47 12 15/32 12.0 29/32 23.0 1/2 2.3
98 47 13 1/2 13.0 29/32 23.2 1/2 2.3
98 47 14 35/64 14.0 31/32 24.5 1/2 2.4
98 47 16 5/8 16.0 1 1/16 26.9 1/2 2.4
98 47 17 43/64 17.0 1 7/64 28.2 1/2 2.6
98 47 18 23/32 18.0 1 9/64 29.0 1/2 2.9
98 47 19 3/4 19.0 1 7/32 30.7 1/2 3.5
98 47 22 55/64 22.0 1 23/64 34.5 1/2 4.4
98 47 24 15/16 24.0 1 29/64 37.0 1/2 5.3
98 47 27 1 1/16 27.0 1 39/64 41.0 1/2 6.5
98 47 1/2“ 1/2 29/32 23.2 1/2 2.4
98 47 9/16“ 9/16 31/32 24.5 1/2 2.3
98 47 5/8“ 5/8 1 1/16 26.9 1/2 2.5
98 47 11/16“ 11/16 1 7/64 28.2 1/2 3.1
98 47 3/4“ 3/4 1 7/32 30.7 1/2 3.4
98 47 7/8“ 7/8 1 23/64 34.5 1/2 4.4
98 47 1“ 1 0 00/00 41.0 1/2 167
Sd
158
insulAted tools
984 Reversible Ratchet with driving square 1/2“
IEC 60900 ASTM F1505
98 42
■ reversible for clockwise and counter-clockwise directions ■ very reliable coupling of sockets with bolt-activated locking system■ Chrome vanadium steel
Product Number inch mm
Square driveinch Ounces
98 42 10 1/2 265 1/2 21.1
98Torque Wrench with driving square 3/8“ or 1/2“, reversible
IEC 60900 ASTM F1505
98 43 50
■ reversible for tightening of left handed threads ■ lockable torque adjustment ■ very reliable coupling of sockets with bolt-activated locking system■ transparent insulated scale range ■ calibration certificate included ■ Chrome vanadium steel
Product Number inch mm
Range of Application Square driveinch Ounces
98 33 25 11 1/2 290
5 - 25 Nm 3/8 43.4
98 33 50 15 385 5 - 50 Nm 3/8 43.4
98 43 50 15 385 5 - 50 Nm 1/2 43.4
98hexagon sockets for socket screws with driving square 3/8“ or 1/2“
IEC 60900 ASTM F1505
98 39 06
■ for metric socket head screws ■ chrome plated ■ Special tool steel
Width across flats S Length of non-insulated blade Square drive Product Number inch mm
inch mm ± 5/64 inch ± 2 mm inch
Ounces
98 39 05 3 75
13/64 5.0 23/64 9.0 3/8 2.1
98 39 06 3 75 1/4 6.0 25/64 10.0 3/8 2.0
98 49 05 3 75
13/64 5.0 23/64 9.0 1/2 2.4
98 49 06 3 75 1/4 6.0 25/64 10.0 1/2 2.5
98 49 08 3 75 5/16 8.0 7/16 11.0 1/2 3.1
Transparent insulated scale range
S
159
insulAted tools
985 Cable Knives
IEC 60900 ASTM F1505
98 52
98 54
■ ergonomically improved handle shape with comfortable slip guard ■ strong grip thanks to slip-proof soft components ■ thumb recess and "finger hook" at the end of the handle ensure
a good transmission of force when the blade is pulled ■ solid, fixed straight blade ■ transparent protective cap ■ blade: Special tool steel; oil-hardened
98 54back of the blade is plastic coated to avoid short circuits
Blade lengthProduct Number inch mm
Handle inch mm
Ounces
98 52 7 1/4 180 insulating multi-component handle, VDE-tested 1 31/32 50.0 2.4
98 54 7 1/4 180 insulating multi-component handle, VDE-tested 1 31/32 50.0 2.4
985 Dismantling Knives
IEC 60900 ASTM F1505
98 53 03
98 53 13
98 55
■ ergonomically improved handle shape with comfortable slip guard ■ strong grip thanks to slip-proof soft components ■ thumb recess and "finger hook" at the end of the handle ensure
a good transmission of force when the blade is pulled ■ transparent protective cap
98 53 03solid, fixed hook blade; suitable for round cables; blade: special tool steel; oil-hardened
98 53 13narrow, fixed hook blade, sickle-shaped; suitable for sector cables; blade: special tool steel; oil-hardened
98 55solid, fixed hook blade, sickle shaped; with guide shoe at the blade point; no damage of the conductor insulation; blade: surgical steel; stainless, air-hardened
Blade length RadiusProduct Number inch mm
Handle inch mm inch mm
Ounces
98 53 03 6 155 insulating multi-component handle, VDE-tested 1 7/64 28.0 9/32 7.0 2.3
98 53 13 7 1/4 180 insulating multi-component handle, VDE-tested 1 31/32 50.0 1 37/64 40.0 2.3
98 55 6 155 insulating multi-component handle, VDE-tested 1 1/2 38.0 59/64 23.5 2.4
160
insulAted tools
985 Cable Knife
IEC 60900 ASTM F1505
98 56
98 62 01
■ straight blade with special grinding; replaceable ■ with hinged blade guard integrated in the handle; captive ■ back of the blade is plastic coated to avoid short circuits ■ ergonomically shaped safety handle ■ blade: Surgical steel; stainless, air-hardened
Blade lengthProduct Number inch mm
inch mm
Ounces
98 56 7 1/2 185 1 31/32 50.0 2.3
98 56 09 Spare blade for 98 56
986 Flat nose Pliers of plastic insulating
IEC 60900 ASTM F1505
■ full insulation reduces risk of short circuits ■ for meter installation and meter blocking ■ plastic material, fiberglass-reinforced
Product Number inch mm Ounces
98 62 01 7 1/4 180 4.6
986 snipe nose Pliers of plastic insulating
IEC 60900 ASTM F1505
■ full insulation reduces risk of short circuits ■ plastic material, fiberglass-reinforced
98 62 02
986 insulating Clamp
from plastic
DIN VDE 0680-1
98 64 02
■ for holding insulated mats in place ■ with integrated spring ■ fully insulated to avoid short cicuits ■ solid plastic, fiberglass-reinforced
Clamping capacityProduct Number inch mm
inch mm
Ounces
98 64 02 6 150 19/32 15 2.2
Product Number inch mm Ounces
98 62 02 8 3/4 220 4.9
161
insulAted tools
986 Plastic slip-on Caps conical
DIN VDE 0680-1
■ to cover bare live cable ends (max. 25/64“ dia.) ■ plastic
Product Number inch mm
Conductor key
Ounces
98 65 01 3 80 1 0.3
98 65 02 3 80 2 0.3
98 65 03 3 80 3 0.3
986 self-Clamping slip-on Caps
DIN VDE 0680-1
98 65 30
98 65 02
■ to cover bare live cable ends ■ plastic
Product Number inch mm
Inside dia.inch
Inside dia.mm Ounces
98 65 10 4 1/4 110 1 25/64 10.0 1.8
98 65 20 4 1/4 110 1 51/64 20.0 1.8
98 65 30 4 1/4 110 1 3/16 30.0 1.8
9890 PuK® Junior hacksaw
IEC 60900 ASTM F1505
98 90
■ saw blade for metal and wood with 25 teeth per inch; exchangeable
Saw blade lengthProduct Number inch mm inch mm Ounces
98 90 9 1/2 240 6 150.0 6.1
162
9898
9898
9898
automotive set 5 parts
IEC 60900 ASTM F1505
Tradesman’s set 5 parts
IEC 60900 ASTM F1505
high leverage Trademan’s set 5 parts
IEC 60900 ASTM F1505
■ for the Automotive Technician
■ for the Journeyman or Apprentice Electrician■ with insulated tools for working on electrical installations
■ for the Journeyman or Apprentice Electrician■ with insulated tools for working on electrical installations
98 98 20 us
98 98 21 us
98 98 22 us
Product Number
Units
Ounces
98 98 20 us
Automotive Set with insulated tools for working on electrical installations 44.874 08 250 10“ High Leverage Diagonal Cutter 1
88 08 250 10“ Alligator® Water Pump Pliers 1
53704 Slotted Screwdriver MaxxPro 1
53706 Slotted Screwdriver MaxxPro 1
53712 Phillips Screwdriver MaxxPro 1
insulAted tools
Product Number
Units
Ounces
98 98 21 us
Tradesman’s Set with insulated tools for working on electrical installations 40.874 08 200 8“ High Leverage Diagonal Cutter 1
02 08 225 9“ High Leverage Combination Pliers 1
53705 Slotted Screwdriver MaxxPro 1
53712 Phillips Screwdriver MaxxPro 1
54812 Square Screwdriver MaxxPro 1
Product Number
Units
Ounces
98 98 22 us
High Leverage Trademan’s Set with insulated tools for working on electrical installations
48.0
74 08 250 10“ High Leverage Diagonal Cutter 1
09 08 240 9 1/4“ Lineman‘s Pliers 1
53705 Slotted Screwdriver MaxxPro 1
53712 Phillips Screwdriver MaxxPro 1
54812 Square Screwdriver MaxxPro 1
163
Product Number
Units
Ounces
98 98 25 us
Roll-up pouch “Commercial Set“ with insulated tools 64.8
74 08 200 8“ High Leverage Diagonal Cutter 1
88 08 250 10“ Alligator® Water Pump Pliers 1
26 18 200 8“ Long Nose Pliers 1
02 08 225 9“ High Leverage Combination Pliers 1
53705 Slotted Screwdriver MaxxPro 1
53712 Phillips Screwdriver MaxxPro 1
54812 Square Screwdriver MaxxPro 1
Product Number
Units
Ounces
98 98 26 us
Roll-up pouch “High Leverage Commercial Set“ with insulated tools 71.2
09 08 240 9 1/4“ Lineman‘s Pliers 1
26 18 200 8“ Long Nose Pliers 1
88 08 250 10“ Alligator® Water Pump 1
74 08 250 10“ High Leverage Diagonal Cutter 1
53705 Slotted Screwdriver MaxxPro 1
53712 Phillips Screwdriver MaxxPro 1
54812 Square Screwdriver MaxxPro 1
Product Number
Units
Ounces
98 98 27 us
Roll-up pouch “Commercial Set“, the Si807 with insulated tools 64.0
26 18 200 8“ Long Nose Pliers 1
74 08 200 8“ High Leverage Diagonal Cutter 1
02 08 225 9“ High Leverage Combination Pliers 1
88 08 250 10“ Alligator® Water Pump Pliers 1
53704 Slotted Screwdriver, MaxxPro 1
53706 Slotted Screwdriver MaxxPro 1
53712 Phillips Screwdriver MaxxPro 1
insulAted tools
9898 Roll-up pouches
with insulated tools 7 parts
IEC 60900 ASTM F1505
Commercial set
high leverage Commercial set
Commercial set, the si807
■ specific assortments to meet the needs of demanding trade professionals
■ in a roll-up ballistic material pouch■ for the small to medium-sized electrical contractor who needs to have
a set of insulated tools at all times and wants the very best■ with sturdy, adjustable snap closure■ all tools 100% tested and meet ASTM F1505 and IEC 60900
requirements■ Dimensions flat (W x H x D): 23 7/32 x 1 31/32 x 12 19/32“■ Dimensions rolled-up (W x H x D): 4 33/64 x 4 33/64 x 12 19/32“
98 98 25 us
98 98 26 us
98 98 27 us
164
Product Number
Units
Ounces
98 98 30 us
Compact Tool Case “Industrial Set“ with insulated tools 104.0
02 08 225 9“ High Leverage Combination Pliers 1
74 08 200 8“ High Leverage Diagonal Cutter 1
95 18 165 6 1/2“ Cable Shears 1
26 18 200 8“ Long Nose Pliers 1
88 08 250 10“ Alligator® Water Pump Pliers 1
53704 Slotted Screwdriver MaxxPro 1
53706 Slotted Screwdriver MaxxPro 1
53711 Phillips Screwdriver MaxxPro 1
53712 Phillips Screwdriver MaxxPro 1
54812 Square Screwdriver MaxxPro 1
Product Number
Units
Ounces
98 98 31 us
Compact Tool Case “High Leverage Industrial Set“ with insulated tools 112.0
74 08 250 10“ High Leverage Diagonal Cutter 1
95 18 165 6 1/2“ Cable Shears 1
09 08 240 9 1/4“ Lineman‘s Pliers 1
26 18 200 8“ Long Nose Pliers 1
88 08 250 10“ Alligator® Water Pump Pliers 1
53704 Slotted Screwdriver MaxxPro 1
53706 Slotted Screwdriver MaxxPro 1
53711 Phillips Screwdriver MaxxPro 1
53712 Phillips Screwdriver MaxxPro 1
54812 Square Screwdriver MaxxPro 1
insulAted tools
9898 Compact Tool Cases
with insulated tools 10 parts
IEC 60900 ASTM F1505
industrial set for the industrial electrician
high leverage industrial set for the industrial electrician
■ specific assortments to meet the needs of demanding trade professionals
■ all tools 100% tested and meet ASTM F1505 and IEC 60900 requirements
■ high quality, versatile, shock-resistant plastic case■ foam insert with honeycomb structure for variable equipment■ Dimensions exterior (W x H x D): 17 1/8 x 3 15/16 x 12 25/64“
Dimensions interior (W x H x D): 16 19/64 x 3 5/32 x 11 39/64“
98 98 30 us
98 98 31 us
165
insulAted tools
Product Number
Units
Ounces
98 99 11 s3
Safety compact tool case with insulated tools (3/8“) for working on electrical installations
115.2
98 31 Reversible Ratchet 1
98 35 125 Extension Bar 1
98 35 250 Extension Bar 1
98 37 1/2“ Hexagon socket for hexagonal screws 1
98 37 3/4“ Hexagon socket for hexagonal screws 1
98 37 3/8“ Hexagon socket for hexagonal screws 1
98 37 5/16“ Hexagon socket for hexagonal screws 1
98 37 5/8“ Hexagon socket for hexagonal screws 1
98 37 7/16“ Hexagon socket for hexagonal screws 1
98 37 9/16“ Hexagon socket for hexagonal screws 1
Product Number
Units
Ounces
98 99 11 s4
Safety compact tool case with insulated tools (3/8“) for working on electrical installations
119.2
98 31 Reversible Ratchet 1
98 35 125 Extension Bar 1
98 35 250 Extension Bar 1
98 37 10 Hexagon socket for hexagonal screws 1
98 37 11 Hexagon socket for hexagonal screws 1
98 37 12 Hexagon socket for hexagonal screws 1
98 37 13 Hexagon socket for hexagonal screws 1
98 37 14 Hexagon socket for hexagonal screws 1
98 37 17 Hexagon socket for hexagonal screws 1
98 37 19 Hexagon socket for hexagonal screws 1
9898 safety compact tool case 10 parts
IEC 60900 ASTM F1505
■ shock-resistant plastic case■ foam insert with precise recesses for holding the pliers■ equipped with a range of custom insulated KNIPEX tools for
work on electrical installations■ all tools 100% tested and meet ASTM F1505 and IEC 60900
requirements■ Dimensions exterior (W x H x D): 14 31/32 x 3 11/32 x 10 15/64“■ Dimensions interior (W x H x D): 13 3/16 x 2 3/4 x 9 3/64“
98 99 11 s3
98 99 11 s4
166
Product Number
Units
Ounces
98 99 11 s5
Safety compact tool case with insulated tools (1/2“) for working on electrical installations
115.2
98 41 Reversible Ratchet 1
98 45 125 Extension Bar 1
98 45 250 Extension Bar 1
98 47 1/2“ Hexagon socket for hexagonal screws 1
98 47 1 Hexagon socket for hexagonal screws 1
98 47 11/16“ Hexagon socket for hexagonal screws 1
98 47 3/4“ Hexagon socket for hexagonal screws 1
98 47 5/8“ Hexagon socket for hexagonal screws 1
98 47 7/8“ Hexagon socket for hexagonal screws 1
98 47 9/16“ Hexagon socket for hexagonal screws 1
Product Number
Units
Ounces
98 99 11 s6
Safety compact tool case with insulated tools (1/2“) for working on electrical installations
119.2
98 41 Reversible Ratchet 1
98 45 125 Extension Bar 1
98 45 250 Extension Bar 1
98 47 13 Hexagon socket for hexagonal screws 1
98 47 14 Hexagon socket for hexagonal screws 1
98 47 17 Hexagon socket for hexagonal screws 1
98 47 19 Hexagon socket for hexagonal screws 1
98 47 22 Hexagon socket for hexagonal screws 1
98 47 24 Hexagon socket for hexagonal screws 1
98 47 27 Hexagon socket for hexagonal screws 1
98 99 11 s5
98 99 11 s6
insulAted tools
9898 safety compact tool case 10 parts
IEC 60900 ASTM F1505
■ shock-resistant plastic case■ foam insert with precise recesses for holding the pliers■ equipped with a range of custom insulated KNIPEX tools for
work on electrical installations■ all tools 100% tested and meet ASTM F1505 and IEC 60900
requirements■ Dimensions exterior (W x H x D): 14 31/32 x 3 11/32 x 10 15/64“■ Dimensions interior (W x H x D): 13 3/16 x 2 3/4 x 9 3/64“
167
insulAted tools
989 standard Tool Case 26 parts
with insulated tools for working on electrical installations
IEC 60900 ASTM F1505
98 99 12
■ containing a range of insulated KNIPEX tools for work on electrical installations
■ shock-resistant plastic case ■ foam inserts with recesses for the tools ■ fixable partition wall ■ Dimensions exterior (W x H x D): 17 21/64 x 4 1/8 x 15 5/32“
Product Number
Units
Ounces
98 99 12
Standard Tool Case 26 parts 149.2
03 07 200 8“ Combination Pliers 1 70 07 160 6 1/4“ Diagonal Cutter 1 98 00 10
Open End Wrench
1
98 00 11 1
98 00 12 1
98 00 13 1
98 00 14 1
98 00 17 1
98 00 19 1
98 53 03 Dismantling Knife for round cable 1 98 20 25
Screwdrivers for slotted screws
1
98 20 35 1
98 20 40 1
98 20 55 1
98 24 00
Screwdrivers for cross-recessed screws, Phillips®
1
98 24 01 1
98 24 02 1
98 40 T-handle 1 98 47 10
Hexagon Socket for hexagonal screws
1
98 47 11 1
98 47 12 1
98 47 13 1
98 47 14 1
98 47 17 1
98 47 19 1
98 52 Cable Knife 1
168
insulAted tools
989 Tool Roll 15 parts
with insulated tools for working on electrical installations
IEC 60900 ASTM F1505
98 99 13
■ tool roll made of hard-wearing polyester fabric ■ with practical, adjustable quick release fastener ■ containing a range of insulated KNIPEX tools for work
on electrical installations
Product Number
Units
Ounces
98 99 13
Tool Roll 15 parts 86.6
03 07 200 8“ Combination Pliers 1 11 07 160 6 1/4“ Insulation Stripper 1 26 17 200 8“ Snipe Nose Side Cutting Pliers 1 70 07 160 6 1/4“ Diagonal Cutter 1 95 17 200 8“ Cable Shears 1 98 00 10
Open End Wrench
1
98 00 13 1
98 00 14 1
98 00 17 1
98 00 19 1
98 20 25
Screwdriver for slotted screws
1
98 20 40 1
98 20 55 1
95 20 65 1
98 52 Cable Knife 1 98 99 13 LE Tool roll empty 1
169
insulAted tools
989 safety tool rolls 8 parts
IEC 60900 ASTM F1505
98 99 13 s4
■ plastic tool roll■ equipped with open end wrenches for work on electrical installations■ all tools 100% tested and meet ASTM F1505 and IEC 60900
requirements■ Dimensions, rolled out (W x H x D): 16 9/64 x 63/64 x 11 13/32“■ Dimensions, rolled up (W x H x D): 2 61/64 x 2 61/64 x 11 13/32“
Product Number
Units
Ounces
98 99 13 s4
Safety tool roll 86.6
98 00 1/4“ Open End Wrench 1 98 00 5/16“ Open End Wrench 1 98 00 3/8“ Open End Wrench 1 98 00 7/16“ Open End Wrench 1 98 00 1/2“ Open End Wrench 1 98 00 9/16“ Open End Wrench 1
98 00 5/8“ Open End Wrench 1
98 00 3/4“ Open End Wrench 1
Product Number
Units
Ounces
98 99 13 s5
Safety tool roll 86.6
98 00 24 Open End Wrench 1 98 00 22 Open End Wrench 1 98 00 19 Open End Wrench 1 98 00 17 Open End Wrench 1 98 00 14 Open End Wrench 1 98 00 13 Open End Wrench 1
98 00 10 Open End Wrench 1
98 00 08 Open End Wrench 1
170
171
insulAted tools
989 universal Tool Case 48 parts
with insulated tools for working on electrical installations
IEC 60900 ASTM F1505
98 99 14
98 99 14■ hard-wearing version made of ABS material, red; containing a range of
KNIPEX tools for work on electrical installations, tested according to IEC 60900, as well as additional insulating mats, clamps and gloves
■ sturdy aluminum frame with D-shape rings for belt and fix, sturdy center board with multi-purpose push-in facilities by elastic loops and 12 small pockets
■ comfortable handle and mounting device for a "trolley" embedded in the bottom (available ordering ref. 00 21 40 T)
■ metal hinges■ 66 pounds maximum load■ can be opened on one or both sides; bottom tray and cover can be
opened independently■ stands stable in any opening position due to lid-holders and hinge
mechanisms on both sides that register in a position of 45° and 90°■ 3-digit lock and 2 clamp-locks for fixation of the lid■ removable document compartment and removable tool board, with
13 push-in compartments on one side
Product Number
Units
Ounces
98 99 14 Universal Tool Case 48 parts 573.2
03 07 200 8“ Combination Pliers 1 11 17 160 6 1/4“ Insulation Stripper 1 70 07 160 6 1/4“ Diagonal Cutter 1 88 07 250 10“ KNIPEX Alligator® 1 95 17 200 8“ Cable Shears 1 98 00 10 Open End Wrench SW 10 mm 1
98 00 13 Open End Wrench SW 13 mm 198 00 14 Open End Wrench SW 14 mm 1 98 00 17 Open End Wrench SW 17 mm 198 00 19 Open End Wrench SW 19 mm 1 98 00 22 Open End Wrench SW 22 mm 198 01 10 Box Wrench SW 10 mm 1 98 01 13 Box Wrench SW 13 mm 198 01 14 Box Wrench SW 14 mm 1 98 01 17 Box Wrench SW 17 mm 198 01 19 Box Wrench SW 19 mm 1 98 01 22 Box Wrench SW 22 mm 198 67 05 Insulating Mat 3 98 20 25
Screwdriver for slotted screws
1
98 20 40 1 98 20 55 198 20 65 1 98 24 01
Screwdriver for cross-recessed screws, Phillips® 1 98 24 02 1
98 40 T-Handle 1 98 42 Reversible Ratchet 1
98 45 125 Extension Bar 5 in 1 98 45 250 Extension Bar 10 in 1
98 47 10 Hexagon Socket for hexagonal screws SW 10 mm 1
98 47 11 Hexagon Socket for hexagonal screws SW 11 mm 1 98 47 12 Hexagon Socket for hexagonal screws SW 12 mm 198 47 13 Hexagon Socket for hexagonal screws SW 13 mm 1 98 47 14 Hexagon Socket for hexagonal screws SW 14 mm 198 47 17 Hexagon Socket for hexagonal screws SW 17 mm 1 98 47 19 Hexagon Socket for hexagonal screws SW 19 mm 198 47 22 Hexagon Socket for hexagonal screws SW 22 mm 1 98 47 24 Hexagon Socket for hexagonal screws SW 24 mm 198 52 Cable Knife 1
98 53 03 Dismantling Knife for round cable 198 64 02 Insulating Clamp 6 98 65 40 Electricians‘ Gloves 1
■ 2 tilting locks to fix the middle wall to the bottom
■ base tray, height 2 9/32“, can be subdivided by flexible inserts; cover plate with 6 large push-in compartments, can be fixed by a snap
■ ext. dimensions ( W x H x D): 19 19/64 x 10 3/64 x 16 9/64“ int. dimensions (W x H x D): 17 33/64 x (4 1/8 + 4 1/8) x 13 25/32“
172
0011 KniPeX TwinKey®
for all standard cabinets and shut-off systems
■ multifunctional key for the actuation of locking systems from the areas of facilities engineering (heating and sanitation, air-conditioning, electrotechnology), gas and water supply and shut-off systems
■ 8-arm version: two 4-way spider keys connected in a space-saving way using magnets
■ reversible bit: slot 3/64 x 9/32“ and PH 2 cross slot■ key and reversible bit joined by stable stainless steel wire■ quality surface coating■ weight-optimized zinc die cast design
Product Number mm mm mm mm mm Ounces
00 11 01 5 / 6 - 7 / 8 - 9 / 10 - 11 7 - 8 / 9 - 10 / 11 - 12 3 - 5 6 6 - 9 4.8
Product Number inch inch inch inch inch Ounces
00 11 01
13/6415/64 - 9/32 5/16 - 23/6425/64 - 7/16
9/32 - 5/16 23/64 - 25/647/16 - 15/32
1/8 - 13/64 15/64 15/64 - 23/64 4.8
00 11 01
control cAbinet keys
173
control cAbinet keys
0011 Control Cabinet Keys
for all standard cabinets and shut-off systems
00 11 03
■ for control cabinets and shut-off systems in the supply of gas, water and electricity
■ for technical installations in buildings, e.g. air conditioning and ventilation systems, shut-off valves, main switch-boards, etc.
■ with bit insert: slot 3/64 x 9/32“ and cross recess PH 2
■ with adapter for 1/4“ bits on securing chain
■ additional bit adapter for 1/4“ bits in one arm
■ zinc die casting
00 11 02short execution, total length 1 3/4“
Product Number inch mm inch mm inch mm inch mm Ounces
00 11 02 1 3/4 44 13/64 / 15/64 / 5/16 5 / 6 / 8 23/64 9 1/8-13/64 3-5 2.3
00 11 03 3 76 13/64 / 15/64 / 5/16 5 / 6 / 8 23/64 9 1/8-13/64 3-5 3.1
0011 Profi-Key
for all standard shut-off systems
00 11 04
■ key for heating, air-conditioning, sanitation and building enginee-ring, e.g. for door and window handles or for air bleeding heaters
■ with bit insert: slot 3/64 x 9/32“ and cross recess PH 2
■ with adapter for 1/4“ bits on securing chain
■ additional bit adapter for 1/4“ bits in one arm
■ total length: 3 1/2“ ■ zinc die casting
Product Number inch mm mm mm inch mm inch mm Ounces
00 11 04 3 1/2 90 13/64 / 9/32 / 5/16 5 / 7 / 8 23/64 - 25/64 9 - 10 15/64 / 9/32 / 5/16 / 23/64 6 / 7 / 8 / 9 3.0
0011 universal Key
for all standard cabinets and shut-off systems
00 11 06
■ for locking systems in electrical engineering, the supply of gas and water, air conditioning and ventilation systems, industry, technical installations in buildings, etc.
■ 9 different die cast zinc key profiles in one tool
■ with detachable chain and snap hook
■ total length: 3 1/2“ ■ zinc die casting
Product Number inch mm inch mm inch mm inch mm inch mm Ounces
00 11 06 3 1/2 90 13/64 / 15/64 / 9/32 - 5/16 / 23/64 - 25/64 5 / 6 / 7 - 8 / 9 - 10 9/32 / 5/16 - 23/64 /
25/64 - 7/16 7 / 8-9 / 10 - 11 1/8-13/64 3-5 15/64 6 7.8
174
control cAbinet keys
0011 Pen-style Control Cabinet Key
for all standard cabinets and shut-off systems
00 11 07
■ easy to carry pen-style control cabinet key with fastening clip ■ four different key profiles can be utilized by swivelling the key holder ■ for control cabinets and shut-off systems in the supply of gas,
water and electricity ■ for technical installations in buildings, e.g. air conditioning and
ventilation systems, shut-off valves, main switch-boards, etc. ■ universal 1/4“ bit adapter for standard bits
(permanent magnet for retaining) ■ additional bit adapter for 1/4“ bits inside one key profile ■ with bit insert: cross recess PH 2 and option of safekeeping
a second bit ■ tool body: plastic, fiberglass-reinforced ■ key profiles: zinc die casting
Product Number inch mm inch mm inch mm inch mm Ounces
00 11 07 5 3/4 145 13/64 / 15/64 / 5/16 5 / 6 / 8 23/64 9 1/8-13/64 3-5 5.4
0011 Pen-style Profi-Key
for all standard shut-off systems
00 11 08
■ easy to carry pen-style control cabinet key with fastening clip
■ three different key profiles can be utilized by swivelling the key holder
■ multi-purpose wrench for all work on construction sites with profiles for the areas of heating, air conditioning, plumbing and building services engineering, e.g. for door and window handles or for bleeding air from radiators
■ universal 1/4“ bit adapter for standard bits (permanent magnet for retaining)
■ additional bit adapter for 1/4“ bits inside one key profile
■ with bit insert: cross recess PH 2 and option of safekeeping a second bit
■ tool body: plastic, fiberglass-reinforced
■ key profiles: zinc die casting
Product Number inch mm inch mm inch mm inch mm Ounces
00 11 08 5 3/4 145 13/64 / 5/16 5 / 8 23/64 9 15/64 / 9/32 / 5/16 / 23/64 6 / 7 / 8 / 9 5.0
175
tool kits
0019 Counter displays
00 19 12 v03
■ made from high-quality paperboard printed with high gloss finish
Width Hight DepthProduct Number
Contents Quantity inch mm inch mm inch mm
Ounces
00 19 12 v03 87 01 125 KNIPEX Cobra® 12 11 27/64 290.0 11 1/64 280.0 6 19/64 160.0 43.9
0019 Counter displays 10 parts
00 19 19 v02
■ eye-catching packaging with neutral header ■ small size, minimum space required at the point of sale ■ dimensions, assembled (W x H x D): 8 55/64 x 17 1/8 x 8 55/64“ ■ dimensions, packed (W x H x D): 10 15/64 x 13 25/32 x 10 15/64“■ other contents (5 + 5 or 10 pieces) with minimum quantity
and delivery time on request ■ material: sturdy cardboard, printed
Product Number
Equipping
Ounces
00 19 19 v01 10 x 68 01 200 127.300 19 19 v02 10 x 87 01 250 125.600 19 19 v03 10 x 88 01 180 78.300 19 19 v04 10 x 88 01 250 127.300 19 19 v08 5 x 86 03 180 / 5 x 86 03 250 154.100 19 19 v09 5 x 87 01 180 / 5 x 87 01 250 89.600 19 19 v10 5 x 87 01 250 / 5 x 87 01 300 163.800 19 19 v11 5 x 88 01 250 / 5 x 88 01 300 161.200 19 19 v12 5 x 99 00 250 / 5 x 99 00 280 154.100 19 19 v13 10 x 71 01 200 134.700 19 19 v15 10 x 88 01 300 196.700 19 19 v16 10 x 87 01 180 76.400 19 19 v17 10 x 87 01 300 203.400 19 19 v18 10 x 99 00 220 111.100 19 19 v19 10 x 99 00 250 118.200 19 19 v20 10 x 99 00 280 160.500 19 19 v21 10 x 99 14 250 123.500 19 19 v22 5 x 88 01 180 / 5 x 88 01 250 107.100 19 19 v33 5 x 88 01 180 / 5 x 88 01 300 157.9
176
tool kits
0019 Circlip Pliers sets 4 parts
00 19 56
00 19 57
■ tool roll made of hard-wearing polyester fabric ■ with practical, adjustable quick release fastener
00 19 56contains 4 Circlip Pliers for internal and external circlips
00 19 57contains common Precision Circlip Pliers for highest requirements
TipsProduct Number
Style Ø inch Ø mm Quantity
Ounces
00 19 56
Set of Circlip Pliers 4 parts 23.6
44 11 J2 Circlip Pliers straight tips 3/4 - 2 23/64 19 - 60 144 21 J21 Circlip Pliers bent tips 3/4 - 2 23/64 19 - 60 1 90°
46 11 A2 Circlip Pliers straight tips 3/4 - 2 23/64 19 - 60 1 46 21 A21 Circlip Pliers bent tips 3/4 - 2 23/64 19 - 60 1 90°
00 19 57
Set of Circlip Pliers 4 parts 23.5
48 11 J1 Precision Circlip Pliers straight tips 15/32 - 63/64 12 - 25 1 48 11 J2 Precision Circlip Pliers straight tips 3/4 - 2 23/64 19 - 60 1 49 11 A1 Precision Circlip Pliers straight tips 25/64 - 63/64 10 - 25 1 49 11 A2 Precision Circlip Pliers straight tips 3/4 - 2 23/64 19 - 60 1
177
Product Number
Style Ø inch Ø mm Quantity
Ounces
00 20 03 sb
Precision Circlip Pliers Set 24.2 48 11 J1 straight tips 15/32 - 63/64 12 - 25 1
48 11 J2 straight tips 3/4 - 2 23/64 19 - 60 1 49 11 A1 straight tips 25/64 - 63/64 10 - 25 1
49 11 A2 straight tips 3/4 - 2 23/64 19 - 60 1
00 20 04 sb
Precision Circlip Pliers Set 45.048 11 J1 straight tips 15/32 - 63/64 12 - 25 1
48 11 J2 straight tips 3/4 - 2 23/64 19 - 60 149 11 A1 straight tips 25/64 - 63/64 10 - 25 1
49 11 A2 straight tips 3/4 - 2 23/64 19 - 60 148 21 J11 bent tips 15/32 - 63/64 12 - 25 1
90° 48 21 J21 bent tips 3/4 - 2 23/64 19 - 60 149 21 A11 bent tips 15/32 - 63/64 12 - 25 1
90° 49 21 A21 bent tips 3/4 - 2 23/64 19 - 60 1
tool kits
0020 Precision Circlip Pliers sets
00 20 03 sb
00 20 04 sb
■ attractive sales packaging ■ contains common Precision Circlip Pliers for highest requirements ■ sturdy plastic packaging, also suitable for storage of the pliers
00 20 03 sb4 parts
00 20 04 sb8 parts
178
tool kits
00 20 05 us00 00 20 06 us1
00 20 06 us200 20 07 us1
0020 Pliers sets ■ popular pliers sets packaged in durable plastic packaging
00 20 08 us100 20 08 us2
179
tool kits
Cutting capacitiesProduct Number inch mm Ø inch Ø inch Ø inch Ø mm Ø mm Ø mm
QuantityOunces
00 20 05 us 74 01 160 High Leverage Diagonal Cutter 6 1/4 160 1/8 3/32 5/64 3.4 2.5 2.0 1 964
74 01 250 High Leverage Diagonal Cutter 10 250 3/16 9/64 1/8 4.6 3.5 3.0 1
74 21 200 High Leverage Diagonal Cutter 8 200 12° 11/64 1/8 3/32 4.2 3.0 2.5 1
00 20 06 us1 87 01 180 KNIPEX Cobra® 7 1/4 180
1/8 3/32 5/64 3.4 2.5 2.0 1 1211
87 01 250 KNIPEX Cobra® 10 250 3/16 9/64 1/8 4.6 3.5 3.0 1
87 01 300 KNIPEX Cobra® 12 300 1/8 3/32 5/64 3.4 2.5 2.0 1
00 20 06 us2 86 03 180 KNIPEX Pliers Wrench 7 1/4 180
1/8 3/32 5/64 3.4 2.5 2.0 1 1643
86 03 250 KNIPEX Pliers Wrench 10 250 3/16 9/64 1/8 4.6 3.5 3.0 1
86 03 300 KNIPEX Pliers Wrench 12 300 1/8 3/32 5/64 3.4 2.5 2.0 1
00 20 07 us1 88 01 180 KNIPEX Alligator® 7 1/4 180
1/8 3/32 5/64 3.4 2.5 2.0 1 1176
88 01 250 KNIPEX Alligator® 10 250 3/16 9/64 1/8 4.6 3.5 3.0 1
88 01 300 KNIPEX Alligator® 12 300 1/8 3/32 5/64 3.4 2.5 2.0 1
00 20 08 us1 26 11 200 Snipe Nose Side Cutting Pliers 8 200 1/8 3/32 5/64 3.2 2.2 2.0 1 904
74 21 200 High Leverage Diagonal Cutter 8 200 12° 11/64 1/8 3/32 4.2 3.0 2.5 1
88 01 250 KNIPEX Alligator® 10 250 1/8 3/32 5/64 3.4 2.5 2.0 1
00 20 08 us2 26 11 200 Snipe Nose Side Cutting Pliers 8 200 1/8 3/32 5/64 3.2 2.2 2.0 1 909
74 21 200 High Leverage Diagonal Cutter 8 200 12° 11/64 1/8 3/32 4.2 3.0 2.5 1
87 01 250 KNIPEX Cobra® 10 250 1/8 3/32 5/64 3.4 2.5 2.0 1
180
tool kits
0020 Pliers sets in a foam tray
00 20 01 v01
00 20 01 v02
00 20 01 v03
■ packaged in a foam tray for workbenches and tool trolleys ■ clearly organized storage of tools ■ precisely-sized recesses for holding the pliers ■ foam insert dimensions (LxWxH): 13 3/16 x 6 1/2 x 1 19/64“ ■ material: two color, closed pore foam
00 20 01 v014 pliers in a foam tray
00 20 01 v026 Circlip Pliers in a foam tray
00 20 01 v033 pliers in a foam tray
Product Number
Quantity
Ounces
00 20 01 v01
Pliers Set ”Basic“ 4 pliers in a foam tray 38.6
03 05 180 7 1/4“ Combination Pliers 1
26 15 200 8“ Snipe Nose Side Cutting Pliers 1
74 05 180 7 1/4“ High Leverage Diagonal Cutter 1
87 01 250 10“ KNIPEX Cobra® 1
00 20 01 v02
Circlip Pliers Set 6 circlip pliers in a foam tray 32.3
48 11 J1 Precision Circlip Pliers 1
48 11 J2 Precision Circlip Pliers 1
48 21 J21 Precision Circlip Pliers 1 90°
49 11 A1 Precision Circlip Pliers 1
49 11 A2 Precision Circlip Pliers 1
49 21 A21 Precision Circlip Pliers 1 90°
00 20 01 v03
Water Pump Pliers Set 3 pliers in a foam tray 37.6
85 01 250 10“ KNIPEX Auto Adjusting Pliers 1
87 41 250 10“ KNIPEX Raptor™ Pliers 1
87 51 250 10“ KNIPEX Cobra® ES 1
181
tool kits
0020 Pliers sets
00 20 11
■ popular pliers sets packaged in a heavy duty display box ■ material: sturdy cardboard packaging, printed
00 20 09 v01pliers with polished heads; handles with either non-slip plastic coating or with two-color multi-component grips
00 20 10pliers with polished heads and plastic coated handles
00 20 11pliers with two-color multi-component grips
Product Number
Quantity
Ounces
00 20 09 v01
Bestseller Pack 33.5
03 02 180 7 1/4“ Combination Pliers 1
70 02 160 6 1/4“ Diagonal Cutter 1
87 01 250 10“ KNIPEX Cobra® 1
00 20 10
Power-Pack 34.9
02 01 180 7 1/4“ High Leverage Combination Pliers 1
74 01 160 6 1/4“ High Leverage Diagonal Cutter 1
87 01 250 10“ KNIPEX Cobra® 1
00 20 11
Assembly Pack 33.0
03 02 180 7 1/4“ Combination Pliers 1
26 12 200 8“ Snipe Nose Side Cutting Pliers 1
70 02 160 6 1/4“ Diagonal Cutter 1
0020 Compact-box
4 parts with vDe tools
00 20 15
■ contains four popular insulated tools■ high quality, versatile, shock-resistant plastic case ■ foam insert ■ outside dimensions (H x W x D): 2 9/16 x 12 7/8 x 10 53/64“
00 20 15all pliers VDE tested according to IEC 60900 and ASTM F1505, pliers finish 6
Product Number
Quantity
Ounces
00 20 15 50.4
03 06 180 Combination Pliers 1
11 06 160 Wire Stripper 1
26 16 200 Snipe Nose Side Cutting Pliers 1
70 06 160 Diagonal Cutter 1
00 20 1000 20 09 v01
182
0020 electronics Pliers sets
for working on electronic components
00 20 16 00 20 17
00 20 167 parts, contains 6 Eectronics Pliers and one pair of Precision Tweezers; case made of hard-wearing polyester fabric; pliers are held by elastic band, with zip fastener
00 20 176 parts, contains 6 ESD Electronics Pliers, electrically discharging version; case made of hard-wearing polyester fabric; pliers are held by elastic band, with zip fastener
Product Number
Equipping
Ounces
00 20 16 35 12 115 / 35 22 115 / 35 32 115 / 64 32 120 / 77 02 115 / 77 42 115 / 92 34 36 25.4
00 20 17 35 12 115 ESD / 35 22 115 ESD / 35 42 115 ESD / 64 32 120 ESD / 77 02 115 ESD / 77 32 115 ESD 24.5
tool kits
0020 KniPeX minis in belt pouch
2-piece
00 20 72 v01
■ KNIPEX “mini“ pliers in a practical tool belt ■ made of hard-wearing polyester fabric ■ with hook and loop fastener ■ with elastic side holder ■ with practical belt loop ■ Dimensions (W x H x D): 2 49/64 x 6 11/16 x 1 31/32“
Product Number
Quantity
Ounces
00 20 72 v01
KNIPEX Minis in belt pouch 2 parts 12.3
86 03 150 6“ Pliers Wrench 1
87 01 125 5“ KNIPEX Cobra® 1
183
0021 Tool box 7 parts
for electrical contractors
00 21 15
■ high quality and versatile shock-resistant case ■ foam insert ■ outside dimensions (H x W x D): 2 9/16 x 12 7/8 x 10 53/64“
00 21 15all pliers and screwdrivers except Water Pump Pliers VDE tested according to IEC 60900 / ASTM F1505
Product Number
Quantity
Ounces
00 21 15 Tool Box 7 parts 53.6
03 06 180 7 1/4“ Combination Pliers
Knipex
1
26 16 200 8“ Snipe Nose Side Cutting Pliers 1
70 06 160 6 1/4“ Diagonal Cutter 1
88 03 180 7 1/4“ KNIPEX Alligator® 1
006100Screwdrivers for slotted screws
Wera
1 006115 1
006152Screwdrivers for cross recessed Phillips screws
1
tool kits
184
tool bAgs And tool cAses
00 19 73 le
00 19 72 le
0019 belt Tool Pouch ■ made of hard-wearing polyester fabric and leather
■ with pockets for up to 8 tools ■ tool loops made of leather, riveted ■ with snap hook■ pliers not included
Product Number
Widthinch
Heightinch
Depthinch
Widthmm
Heightmm
Depthmm Ounces
00 19 73 le 6 11/16 9 1/4 2 61/64 170.0 235.0 75.0 7.4
0019 belt Pouch for two pliers ■ for two pliers up to 6“ length
■ made of hard-wearing polyester fabric ■ with hook and loop fastener ■ with elastic side holder ■ with practical belt loop■ pliers not included
Product Number
Widthinch
Heightinch
Depthinch
Widthmm
Heightmm
Depthmm Ounces
00 19 72 le 2 9/16 6 7/64 1.0 65.0 155.0 25.0 2.3
185
tool bAgs And tool cAses
0021 Tool Case “big Twin-move“
with integrated rollers and telescopic handle
empty
00 21 41 le
■ heavy duty ABS material, black ■ all around aluminium frame and firmly-mounted sturdy center board,
each side offering multi-purpose push-in facilities by elastic loops and 12 small pockets
■ pull-out handle embedded in the base and two wheels ■ 66 pound maximum load ■ can be opened on one or both sides (V form); base tray and cover
can be partially or fully opened independently of each other; stands securely in all opening positions; the special wheels are easy on the floor and ensure stability
■ lockable ■ removable document compartment and removable tool panel
with 13 tool pouches ■ base tray, height 2 23/64, can be subdivided by flexible inserts; tool
panel as cover plate with 13 tool pouches ■ dimensions, outside (W x H x D): 20 5/64 x 10 5/8 x 16 9/64“ ■ dimensions, lid, inside (W x H x D): 18 29/32 x 4 1/8 x 14 37/64“ ■ dimensions, base, inside (W x H x D): 17 33/64 x 4 1/8 x 13“
Dimension external (internal)Product Number
widthinch
heightinch
depthinch
widthmm
height mm
depth mm Ounces
00 21 41 le 20 5/64 (18 29/32 17 33/64) 10 5/8 (4 1/8 4 1/8) 16 9/64 (14 37/64 13) 510 (480 / 445) 270 (105 / 105) 410 (370 / 330) 303.4
186
sAles Aids
0019 Test supports
00 19 2000 19 21 T
00 19 20for showing the self-locking function of the Alligator® and Cobra® Water Pump Pliers; steady stand, high stability; pliers not included
00 19 21 Tfor testing the ratchet-action of the Pliers Wrench; can be fixed on the wall; pliers not included
Product Number
Widthinch
Heightinch
Depthinch
Widthmm
Heightmm
Depthmm Ounces
00 19 20 9 1/16 6 1/2 12 13/64 230.0 165.0 310.0 49.0
00 19 21 T 3 11/32 3 11/32 5 29/32 85.0 85.0 150.0 26.0
0019 sales Display
00 19 25
■ for 8 x 7 pliers ■ solid style; can be adhered to a tool bar or used as a counter display ■ with header ■ assortment on request ■ product detail header available ■ pliers not included ■ material: sheet steel/steel wire, silver powder coated
Product Number
Widthinch
Heightinch
Depthinch
Widthmm
Heightmm
Depthmm Ounces
00 19 25 19 19/64 15 3/4 12 13/64 490.0 400.0 310.0 146.0
187
sAles Aids
0019 magnetic labels
Product Number
Widthinch
Heightinch
Widthmm
Heightmm
00 19 30 15 KNIPEX Quality – Made in Germany 38 37/64 3 15/16 980 100
00 19 30 16 VDE 1000 Volt 38 37/64 3 15/16 980 100
00 19 30 17 KNIPEX Quality – Made in Germany 25 37/64 3 15/16 650 100
00 19 30 18 VDE 1000 Volt 25 37/64 3 15/16 650 100
00 19 30 19 KNIPEX Quality – Made in Germany 35 7/16 7 7/8 900 200
00 19 30 20 KNIPEX pliers 25 37/64 7 7/8 650 200
00 19 30 15
00 19 30 16
00 19 30 19
to be placed on tool bar systems different versions; see table
00 19 30 17
00 19 30 18
00 19 30 20
l130 00330
33 Kg 39 Kg 52 Kg18 Kgwith
reapplication*Required hand forcefor a nail with Ø 3 mm
KNIPEX TwinForce ®
The reapplying cutter*
KNIPEX X-Cut ®
THE WORLD OF THE KNIPEX DIAGONAL CUTTERS
Forged on hinged joint for robust useHand force is multiplied by 13
Long cutting edges for cutting cable; also precise enough for the finest stranded wiresHand force is multiplied by 9
The reapplying cutter
Double-hinged designHand force is multiplied by 39
Box joint: greatest stability with little weight Hand force is multiplied by 16
* notch – reapply – cut through
NEWNEW
KNIPEX TwinForce® High LeverageDiagonal Cutter
Diagonal Cutter
NEW NEW
KNIPEX X-Cut®
Diagonal Cutter
High Leverage Diagonal Cutter
Seitenschneider_660x160_20120828RZ_Sprachen.indd 1 07.11.12 12:03
to be placed on tool bar systems versions in different languages available dimensions, assembled (W x H): 660 x 170 mm
"The World of the KniPeX Diagonal Cutters"
Product Number
Widthinch
Heightinch
Widthmm
Heightmm
l130 00330 en English Version 26 6 11/16 660 170
l130 00330 FR French Version 26 6 11/16 660 170
l130 00330 es Spanish Version 26 6 11/16 660 170
It is not permissible to copy the catalog or parts of it in any way without our approval.
Subject to model modifications and technical changes.
Illustrations, dimensions and weights are just approxi-mate. No liability is assumed for misprints or errors.
Printed in the Federal Republic of Germany.
KNIPEX-Werk C. Gustav Putsch KG 2012
188
sAles Aids
0019 Pliers Racks for tool bar systems
00 19 34 1
00 19 34 2
00 19 34 1for 5 x 6 carded pliers; with header sign
00 19 34 2for 15 x 6 pliers
Product Number
Designation Widthinch
Heightinch
Depthinch
Widthmm
Heightmm
Depthmm Ounces
00 19 34 1 for 5 x 6 carded pliers 18 57/64 7 7/8 8 55/64 480.0 200.0 225.0 37.6
00 19 34 2 for 15 x 6 pliers 39 11/64 5 23/32 8 15/32 995.0 145.0 215.0 79.4
189
sAles Aids
0019 sales Displays
C320 00330C320 00275 C320 00286 C320 00297 C320 00352 C320 00363 C320 00429 C320 00451
00 19 34 3for pliers finish 0; 1; 3 or 4
Article No. EAN4003773-
Designation Widthinch
Heightinch
Depthinch
Widthmm
Heightmm
Depthmm Ounces
00 19 34 3 054450 for 3 x 6 pliers; for pliers finish 0/1/3 or 4 9 29/64 12 39/64 12 13/64 240.0 320.0 310.0 82.5
00 19 34 4 054467 for 3 x 6 pliers; for pliers finish 2/5/8 9 29/64 12 39/64 12 13/64 240.0 320.0 310.0 82.5
C320 00275 054535 Header Precision Circlip Pliers 48/49
C320 00286 054504 Header Concretors‘ Nippers
C320 00297 054481 Header Cobra®; Pliers Wrenches
C320 00330 054511 Header General Programme
C320 00352 060284 Header Multiple Slip Joint Spanners
C320 00363 060291 Header Self-adjusting Insulation Strippers
C320 00429 062271 Header for 74 12
C320 00451 063032 Header Cobra® ES
00 19 34 4for pliers finish 2; 5 or 6
190
indeX Article number / PAge
02 01 180 20
02 01 200 20
02 01 225 20
02 02 180 20
02 02 200 20
02 02 225 20
02 08 200 sba 20
02 08 225 sba 20
03 01 140 21
03 01 180 21
03 01 200 21
03 01 250 21
03 02 160 21
03 02 180 21
03 02 200 21
03 08 160 sba 21
03 08 180 sba 21
03 08 200 sba 21
09 01 240 22
09 02 240 22
09 08 240 22
09 11 240 22
09 12 240 22
11 01 160 23
11 02 160 23
11 08 160 23
11 82 130 24
11 92 140 24
12 21 180 24
12 29 180 24
12 12 02 26
12 12 06 26
12 12 10 26
12 12 11 26
12 12 12 26
12 19 02 26
12 19 06 26
12 19 10 26
12 19 11 26
12 19 12 26
12 40 200 28
12 50 200 28
12 49 01 28
12 49 02 28
12 49 03 28
12 59 01 28
12 59 02 28
12 42 195 29
12 49 21 29
12 49 23 29
12 62 180 30
12 69 21 30
12 69 23 30
12 64 180 30
12 69 31 30
12 80 040 sb 31
13 01 160 31
13 02 160 31
13 01 614 31
13 81 8 32
13 82 8 32
13 88 8 32
13 81 8 32
13 82 8 32
13 88 8 32
15 11 120 33
16 20 16 sb 33
16 30 135 sb 33
16 40 150 sb 34
16 49 150 34
16 65 125 sb 34
19 01 130 35
19 01 130 35
20 01 125 35
20 01 140 35
20 01 160 35
20 01 200 35
20 06 160 35
22 01 125 36
22 01 140 36
22 01 160 36
22 01 180 36
22 02 140 36
22 02 160 36
22 08 160 sba 36
23 01 140 36
23 01 140 36
25 01 125 37
25 01 140 37
25 01 160 37
25 02 140 37
25 02 160 37
25 08 160 sba 37
25 21 160 37
25 01 125 37
25 01 140 37
25 01 160 37
25 02 140 37
25 02 160 37
25 08 160 sba 37
49 21 a11 57
49 21 a21 57
49 21 a31 57
49 21 a41 57
49 31 a0 57
49 41 a01 57
46 10 100 58
50 01 160 59
50 01 180 59
50 01 210 59
50 01 225 59
50 01 250 59
50 01 300 59
51 01 210 59
55 00 300 59
57 00 360 60
99 00 200 60
99 00 220 60
99 00 250 60
99 00 280 60
99 00 300 60
99 01 200 60
99 01 220 60
99 01 250 60
99 01 280 60
99 01 300 60
99 10 250 61
99 10 300 61
99 11 250 61
99 11 300 61
99 14 250 61
99 14 300 61
61 01 200 62
61 01 200 62
62 12 120 62
62 12 120 62
64 02 115 65
64 11 115 65
64 12 115 65
64 22 115 65
64 32 120 65
64 42 115 65
64 52 115 65
64 62 120 65
64 72 120 65
64 02 115 65
64 11 115 65
64 12 115 65
64 22 115 65
64 32 120 65
25 21 160 37
26 11 200 38
26 11 200 s1 38
26 18 200 sba 38
26 12 200 38
26 21 200 38
26 28 200 sba 38
26 22 200 38
26 11 200 38
26 11 200 s1 38
26 18 200 sba 38
26 12 200 38
26 21 200 38
26 28 200 sba 38
26 22 200 38
28 01 200 39
28 21 200 39
29 11 160 39
29 21 160 39
31 11 160 40
31 21 160 40
31 11 160 40
31 21 160 40
30 41 160 40
30 11 190 41
30 16 160 41
30 21 160 41
30 31 140 41
30 31 160 41
30 36 160 41
32 21 135 42
32 31 135 42
33 01 160 42
33 03 160 42
34 12 130 43
34 22 130 43
34 32 130 43
34 12 130 43
34 22 130 43
34 32 130 43
34 12 130 esD 44
34 22 130 esD 44
34 32 130 esD 44
34 12 130 esD 44
34 22 130 esD 44
34 32 130 esD 44
35 11 115 45
35 12 115 45
35 21 115 45
35 22 115 45
35 31 115 45
35 32 115 45
35 42 115 45
35 52 145 45
35 62 145 45
35 72 145 45
35 82 145 45
35 12 115 esD 46
35 22 115 esD 46
35 42 115 esD 46
36 12 130 47
36 22 125 47
36 32 125 47
36 12 130 47
36 22 125 47
36 32 125 47
37 11 125 48
37 21 125 48
37 31 125 48
37 43 125 48
37 11 125 48
37 21 125 48
37 31 125 48
37 43 125 48
38 11 200 49
38 21 200 49
38 31 200 49
38 35 200 49
38 41 190 49
38 71 200 49
38 91 200 49
40 04 180 50
40 04 250 50
41 04 180 50
41 04 250 50
41 04 300 50
41 14 250 50
41 34 165 50
44 11 J0 52
44 11 J1 52
44 11 J2 52
44 11 J3 52
44 11 J4 52
44 21 J01 52
44 21 J11 52
44 21 J21 52
44 21 J31 52
44 21 J41 52
44 31 J02 52
44 31 J12 52
44 31 J22 52
44 31 J32 52
44 31 J42 52
46 11 a0 53
46 11 a1 53
46 11 a2 53
46 11 a3 53
46 11 a4 53
46 21 a01 53
46 21 a11 53
46 21 a21 53
46 21 a31 53
46 21 a41 53
46 31 a02 53
46 31 a12 53
46 31 a22 53
46 31 a32 53
46 31 a42 53
44 10 J5 54
44 10 J6 54
44 20 J51 54
44 20 J61 54
44 19 J6 54
45 10 170 54
45 21 200 54
46 10 a5 55
46 10 a6 55
46 20 a51 55
46 20 a61 55
46 11 g0 55
46 11 g1 55
46 11 g2 55
46 11 g3 55
46 11 g4 55
48 11 J0 56
48 11 J1 56
48 11 J2 56
48 11 J3 56
48 11 J4 56
48 21 J01 56
48 21 J11 56
48 21 J21 56
48 21 J31 56
48 21 J41 56
49 11 a0 57
49 11 a1 57
49 11 a2 57
49 11 a3 57
49 11 a4 57
49 21 a01 57
64 42 115 65
64 52 115 65
64 62 120 65
64 72 120 65
64 62 120 esD 66
64 62 120 esD 66
67 01 140 67
67 01 160 67
67 01 200 67
68 01 160 67
68 01 180 67
68 01 200 67
69 01 130 67
69 01 130 67
70 01 110 69
70 01 125 69
70 01 140 69
70 01 160 69
70 01 180 69
70 02 125 69
70 02 140 69
70 02 160 69
70 02 180 69
70 08 160 sba 69
70 08 180 sba 69
71 01 200 71
71 01 200 R sba 71
71 02 200 71
71 12 200 71
71 21 200 71
71 22 200 71
71 31 200 71
71 31 200 R sba 71
71 32 200 71
71 41 200 71
71 72 460 72
71 72 610 72
71 72 760 72
71 72 910 72
71 82 950 73
72 01 140 74
72 01 160 74
72 01 180 74
72 11 160 74
72 21 160 74
72 51 160 74
73 02 160 75
73 05 160 75
73 06 160 75
73 02 160 75
191
indeX Article number / PAge
73 05 160 75
73 06 160 75
74 01 140 77
74 01 160 77
74 01 180 77
74 01 200 77
74 01 250 77
74 02 140 77
74 02 160 77
74 02 180 77
74 02 200 77
74 02 250 77
74 08 200 77
74 08 250 77
74 12 160 77
74 12 180 77
74 21 160 77
74 21 180 77
74 21 200 77
74 21 250 77
74 22 200 77
74 22 250 77
73 71 180 79
73 72 180 79
73 71 180 79
73 72 180 79
74 91 250 79
74 91 250 79
75 02 125 80
75 12 125 80
75 22 125 80
75 52 125 80
75 02 125 80
75 12 125 80
75 22 125 80
75 52 125 80
76 01 125 81
76 22 125 81
76 81 125 81
76 01 125 81
76 22 125 81
76 81 125 81
77 01 115 83
77 01 130 83
77 02 115 83
77 12 115 83
77 22 115 83
77 22 130 83
77 42 115 83
77 42 130 83
77 52 115 83
77 72 115 83
77 01 115 83
77 01 130 83
77 02 115 83
77 12 115 83
77 22 115 83
77 22 130 83
77 42 115 83
77 42 130 83
77 52 115 83
77 72 115 83
77 02 115 esD 84
77 22 115 esD 84
77 42 115 esD 84
77 02 115 esD 84
77 22 115 esD 84
77 42 115 esD 84
78 03 125 87
78 23 125 87
78 31 125 87
78 41 125 87
78 61 125 87
78 71 125 87
78 03 125 87
78 23 125 87
78 31 125 87
78 41 125 87
78 61 125 87
78 71 125 87
78 03 125 esD 87
78 03 125 esD 87
79 02 120 89
79 02 125 89
79 12 125 89
79 22 120 89
79 22 125 89
79 32 125 89
79 42 125 89
79 02 120 89
79 02 125 89
79 12 125 89
79 22 120 89
79 22 125 89
79 32 125 89
79 42 125 89
79 02 120 esD 91
79 02 125 esD 91
79 12 125 esD 91
79 22 120 esD 91
97 43 06 125
97 49 04 126
97 49 05 126
97 49 06 126
97 49 08 126
97 49 09 126
97 49 13 126
97 49 15 126
97 49 16 126
97 49 18 126
97 49 19 126
97 49 20 126
97 49 23 126
97 49 24 126
97 49 30 126
97 49 35 126
97 49 40 126
97 49 44 126
97 49 50 126
97 49 54 126
97 49 59 126
97 49 60 126
97 49 62 126
97 49 64 126
97 49 66 4 127
97 49 66 6 127
97 49 69 1 127
97 49 69 2 127
97 49 70 127
97 49 74 127
97 49 76 127
97 49 81 127
97 49 82 127
97 49 83 127
97 49 84 127
97 49 87 127
97 49 59 1 127
97 49 65 1 127
97 49 66 1 127
97 49 68 1 127
97 49 69 11 127
97 49 90 127
97 49 93 127
97 49 94 127
97 49 95 127
97 59 65 2 127
97 49 65 2 128
97 51 10 128
97 59 06 128
97 52 05 129
79 22 125 esD 91
79 32 125 esD 91
79 42 125 esD 91
79 52 125 esD 91
79 62 125 esD 91
79 02 120 esD 91
79 02 125 esD 91
79 12 125 esD 91
79 22 120 esD 91
79 22 125 esD 91
79 32 125 esD 91
79 42 125 esD 91
79 52 125 esD 91
79 62 125 esD 91
81 03 230 93
81 13 230 93
81 19 230 93
84 11 200 93
84 21 200 93
83 10 010 94
83 10 015 94
83 10 020 94
83 10 030 94
83 10 040 94
83 20 010 94
83 20 015 94
83 20 020 94
83 30 005 95
83 30 010 95
83 30 015 95
83 30 020 95
83 30 030 95
83 60 010 95
83 60 015 95
86 03 150 97
86 03 180 97
86 03 250 97
86 03 300 97
86 05 150 97
86 05 180 97
86 05 250 97
86 07 250 sba 97
87 01 125 99
87 01 150 99
87 01 180 99
87 01 250 99
87 01 300 99
87 02 180 99
87 02 250 99
87 02 300 99
87 03 125 99
87 03 180 99
87 03 250 99
87 03 300 99
87 05 180 99
87 05 250 99
87 05 300 99
87 01 400 100
87 01 560 100
85 01 250 us 102
87 21 250 103
87 28 250 103
87 41 250 RaP 104
87 51 250 105
87 51 250 105
88 01 180 107
88 01 250 107
88 01 300 107
88 02 180 107
88 02 250 107
88 02 300 107
88 07 250 107
88 08 250 sba 107
90 01 125 108
90 20 185 109
90 29 185 109
90 25 20 109
90 29 01 109
90 29 02 109
90 29 15 109
90 25 40 110
90 29 40 110
90 42 250 110
90 42 340 110
90 49 340 110
90 49 340 m 110
90 55 280 111
90 59 280 111
90 61 16 111
90 61 20 111
90 70 220 112
91 31 180 112
91 51 160 113
91 71 160 113
91 61 160 113
92 22 12 114
92 22 13 114
92 22 35 114
92 34 36 114
92 70 46 114
92 08 78 esD 115
92 28 69 esD 115
92 38 75 esD 115
92 58 74 esD 115
92 27 61 115
92 27 62 115
92 37 64 115
92 67 63 115
95 06 230 116
95 11 165 117
95 12 165 117
95 18 165 sba 117
95 21 165 117
95 22 165 117
95 11 200 117
95 12 200 117
95 18 200 sba 117
95 12 500 118
95 17 500 118
95 31 250 119
95 31 280 119
95 36 250 119
95 36 280 119
95 32 320 119
95 36 320 119
95 39 280 119
95 32 038 120
95 39 038 120
95 32 060 121
95 32 100 121
95 39 720 121
95 39 870 121
95 61 190 122
95 62 190 122
95 61 150 123
95 71 445 123
95 71 600 123
95 77 600 123
95 71 445 123
95 71 600 123
95 77 600 123
95 79 445 123
95 79 600 123
95 89 600 123
97 21 215 124
97 22 240 124
97 32 225 124
97 43 200 125
97 43 200 a 125
97 43 05 125
97 52 06 129
97 52 09 129
97 52 13 129
97 52 19 129
97 52 23 129
97 49 94 129
97 49 95 129
97 51 12 130
97 59 12 130
97 52 14 130
97 52 20 130
97 59 14 130
97 52 30 131
97 52 33 131
97 52 34 131
97 52 35 131
97 52 36 131
97 52 37 131
97 52 50 131
97 49 94 131
97 49 95 131
97 52 63 Dg 132
97 52 65 132
97 52 65 Dg 132
97 59 65 2 132
97 53 04 133
97 53 14 133
97 53 08 134
97 53 09 134
97 61 145 a 135
97 62 145 a 135
97 68 145 a 135
97 71 180 135
97 72 180 135
97 91 01 136
97 49 62 136
97 49 63 136
97 49 65 136
97 49 65 1 136
97 49 65 2 136
97 49 66 136
97 49 66 1 136
97 49 66 4 136
97 49 66 6 136
97 49 67 136
97 49 68 136
97 49 68 1 136
97 49 69 1 136
97 49 69 2 136
97 49 69 11 136
192
indeX Article number / PAge
97 99 42 138
97 99 43 138
97 99 44 138
97 99 45 138
97 99 46 138
97 99 47 138
97 99 48 138
97 99 49 138
97 99 70 138
97 99 71 138
97 99 72 138
97 99 73 138
97 99 74 138
97 99 75 138
97 99 76 138
97 99 77 138
97 99 78 138
97 99 79 138
97 99 92 138
97 99 93 138
97 99 95 138
97 99 96 138
02 08 200 sba 142
02 08 225 sba 142
03 08 160 sba 142
03 08 180 sba 142
03 08 200 sba 142
09 08 240 143
11 08 160 sba 143
13 88 8 143
20 06 160 144
22 08 160 sba 144
30 16 160 144
30 36 160 144
25 08 160 sba 145
25 08 160 sba 145
26 18 200 sba 145
26 28 200 sba 145
26 18 200 sba 145
26 28 200 sba 145
70 08 160 sba 146
70 08 180 sba 146
74 08 200 sba 146
74 08 250 sba 146
73 06 160 147
73 06 160 147
86 07 250 sba 147
87 28 250 sba 148
88 08 250 sba 148
95 06 230 149
95 18 165 sba 149
95 18 200 sba 150
95 17 500 150
95 36 250 151
95 36 280 151
95 39 280 151
95 36 320 151
95 39 280 151
95 77 600 152
95 77 600 152
95 79 600 152
97 68 145 a 152
98 00 7/16“ 153
98 00 1 1/16“ 153
98 01 1 1/16" 153
98 01 1/2“ 153
98 01 1/16“ 153
98 01 3/4“ 153
98 01 3/8“ 153
98 01 5/16“ 153
98 01 5/8“ 153
98 01 7/16“ 153
98 01 7/8“ 153
98 01 9/16“ 153
98 03 04 154
98 03 05 154
98 03 08 154
98 03 10 154
98 03 04 154
98 03 05 154
98 03 08 154
98 03 10 154
98 04 08 154
98 04 17 154
98 04 19 154
98 05 13 154
98 05 17 154
98 05 19 154
98 04 08 154
98 04 17 154
98 04 19 154
98 05 13 154
98 05 17 154
98 05 19 154
98 07 250 155
98 07 250 155
98 14 05 155
98 14 06 155
98 14 08 155
98 15 05 155
98 15 06 155
98 15 08 155
98 14 05 155
98 14 06 155
98 14 08 155
98 15 05 155
98 15 06 155
98 15 08 155
98 30 156
98 40 156
98 31 156
98 41 156
98 35 125 156
98 35 250 156
98 45 125 156
98 45 250 156
98 37 10 157
98 37 11 157
98 37 12 157
98 37 13 157
98 37 14 157
98 37 16 157
98 37 17 157
98 37 19 157
98 37 5/16“ 157
98 37 3/8“ 157
98 37 7/16“ 157
98 37 1/2“ 157
98 37 9/16“ 157
98 37 5/8“ 157
98 37 3/4“ 157
98 37 1/4“ 157
98 47 10 157
98 47 11 157
98 47 12 157
98 47 13 157
98 47 14 157
98 47 16 157
98 47 17 157
98 47 18 157
98 47 19 157
98 47 22 157
98 47 24 157
98 47 27 157
98 47 1/2“ 157
98 47 9/16“ 157
98 47 5/8“ 157
98 47 11/16“ 157
98 47 3/4“ 157
98 47 7/8“ 157
98 47 1“ 157
98 39 05 158
98 39 06 158
98 49 05 158
98 49 06 158
98 49 08 158
98 33 25 158
98 33 50 158
98 43 50 158
98 42 158
98 52 159
98 54 159
98 53 03 159
98 53 13 159
98 55 159
98 56 160
98 56 09 160
98 62 01 160
98 62 02 160
98 64 02 160
98 65 01 161
98 65 02 161
00 19 19 v15 175
00 19 19 v16 175
00 19 19 v17 175
00 19 19 v18 175
00 19 19 v19 175
00 19 19 v20 175
00 19 19 v21 175
00 19 19 v22 175
00 19 19 v33 175
00 19 56 176
00 19 57 176
00 20 03 sb 177
00 20 04 sb 177
00 20 05 us 179
00 20 06 us1 179
00 20 06 us2 179
00 20 07 us1 179
00 20 08 us1 179
00 20 08 us2 179
00 20 01 v01 180
00 20 01 v02 180
00 20 01 v03 180
00 20 09 v01 181
00 20 10 181
00 20 11 181
00 20 15 181
00 20 16 182
00 20 17 182
00 20 72 v01 182
00 21 15 183
00 19 72 le 184
00 19 73 le 184
00 21 41 le 185
00 19 20 186
00 19 21 T 186
00 19 25 186
00 19 30 15 187
00 19 30 16 187
00 19 34 1 187
00 19 34 2 187
00 19 34 4 188
98 65 03 161
98 65 10 161
98 65 20 161
98 65 30 161
98 90 161
98 98 20 us 162
98 98 21 us 162
98 98 22 us 162
98 98 25 us 163
98 98 26 us 163
98 98 27 us 163
98 98 30 us 164
98 98 31 us 164
98 99 11 s3 165
98 99 11 s4 165
98 99 11 s5 166
98 99 11 s6 166
98 99 12 167
98 99 13 168
98 99 13 s4 169
98 99 13 s5 169
98 99 14 171
00 11 01 172
00 11 01 172
00 11 02 173
00 11 03 173
00 11 04 173
00 11 06 173
00 11 07 174
00 11 08 174
00 19 12 v01 175
00 19 12 v02 175
00 19 12 v03 175
00 19 19 v01 175
00 19 19 v02 175
00 19 19 v03 175
00 19 19 v04 175
00 19 19 v08 175
00 19 19 v09 175
00 19 19 v10 175
00 19 19 v11 175
00 19 19 v12 175
00 19 19 v13 175
97 49 59 136
97 91 02 137
97 91 02 le 137
97 99 01 138
97 99 02 138
97 99 03 138
97 99 04 138
97 99 05 138
97 99 06 138
97 99 07 138
97 99 08 138
97 99 09 138
97 99 10 138
97 99 11 138
97 99 12 138
97 99 13 138
97 99 14 138
97 99 15 138
97 99 16 138
97 99 17 138
97 99 18 138
97 99 19 138
97 99 20 138
97 99 21 138
97 99 22 138
97 99 23 138
97 99 24 138
97 99 25 138
97 99 26 138
97 99 27 138
97 99 28 138
97 99 29 138
97 99 30 138
97 99 31 138
97 99 32 138
97 99 33 138
97 99 34 138
97 99 35 138
97 99 36 138
97 99 37 138
97 99 38 138
97 99 40 138
97 99 41 138
KNIPEX-Werk C. Gustav Putsch KG
Oberkamper Straße 13 42349 Wuppertal (Germany)
Tel.: +49 (0) 202-47 94-0 Fax: +49 (0) 202-47 74 94
[email protected] · www.knipex.de
L110 02596/01/12.12/35.000/US
KNIPEX Tools LP 2035 South Arlington Heights Rd.
Suite 110 Arlington Heights, IL 60005 Tel.: +1 (847) 398 8520 Fax: +1 (847) 398 8526
[email protected] · www.knipex-tools.com