Review full instruction manual prior to use for important safety information. AlwayscheckRockler.comtoconfirmthat you are using the most recent manual version for your product.

Downdraft Table Assembly Instructions

2

This product is designed for specific applications as defined in the instructions and should not be modified and/or used for any other applications. Before using the Dust Right® Downdraft Table, read, understand and follow all instructions and safety information provided. KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY WARNINGS

> Always confirm that you are using the most recent version of the Instructions and safety warnings for your product. To find the most recent version, find the product page on Rockler.com and click on the link to the Instructions.

> For any tool used in conjunction with this product, always read, understand and follow the instructions andsafetywarningsintheowner’smanualforthattool. Ifyoudonothavetheowner’smanual,obtainonefrom thetool’smanufacturerbeforeusingitwiththisproduct.

> Before using this product, review and verify that all tools to be used with it have safety equipment installed and are in proper working order as definedbythetools’owner’smanuals.

> Do not use this product until you have read and are confident you understand: • Parts List (p. 3); • Assembly (p. 4); • Holding your Workpiece (p. 4); • Storing you Downdraft Table (p. 4).

> Do not use this product in any manner other than what is described in these instructions. Use only recommended accessories.

> Remain alert and use good judgment when using this tool. Do not use this tool if you are in any way impaired by medications, alcohol, drugs or fatigue.

> Dress appropriately and remove all jewelry, secure loose clothing and tie up long hair before using this tool.

> It is the sole responsibility of the purchaser of this product to ensure that any third party whom you allow to use this product reads and complies with all the instructions and safety precautions outlined in this manual prior to use.

> Maintain these instructions and warnings as long as you own the product. Keep this booklet in a place where it will be readily available for reference.

> The user assumes all risk and responsibility for the proper use of this product and for ensuring product suitability for intended application.

> Always wear safety glasses in compliance with ANSI safety standards and hearing protection and follow all standard shop safety practices, including: • Keep your work area well lit and clean; • Unplug all power tools before making any adjustments or changing accessories; • Use dust collection tools and dust face masks to reduce exposure to dust; • Use accessory safety equipment such as featherboards, push sticks and push blocks whenever appropriate; • Do not use power tools in explosive environments (e.g., in the presence of flammable liquids, fumes or dust); • Keep children and bystanders away from the tool operating area; • Maintain proper footing at all times and do not overreach; • Do not force the tool. > These warnings and instructions do not represent the total of all information available regarding tool safety, use and technique. Please read the full manual before using this product and always seek out opportunities to learn more and improve your skills and knowledge.

Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known ot the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.

Danger indicates a hazardous situation that, if not avoided, will result in death or serious injury.

Warning indicates a hazardous situation that, if not avoided, could result in death or serious injury.

Caution indicates a hazardous situation that, if not avoided, may result in minor or moderate injuryor property damage.

Notice indicates important or helpful information and/or user tips.

BP0617

3

Dust Port Assembly

1

15

8 12

9

13

7

11

5

11

22 1

6

1114

10

14

14

11

11

11

11

10

14

11

11

8

8

4

3

3

Quantity 1 Case 1 2 Leveling Foot 4 3 Adjustment Nut 4 4 Dust Port 1 5 Right Edge Lip 1 6 Left Edge Lip 1 7 Rear Edge Lip 1 8 Downdraft Plate 3

PARTS LIST Quantity 9 Rubber Grommets 48 10 Handle 2 11 Lock Knob 9 12 Stopper Bolt 6 13 Stopper Nut 6 14 Large Pan-head Screw 4 15 Small Pan-head Screw 4

4 Distributed by Rockler Companies, Inc. Medina, MN 55340

57664Rev 12/17

Assembly 1. Turn over the Case (1) so the bottom is facing up.

2. Thread the Leveling Feet and Adjustment Nuts (2) into the holes on the Case (1). You will fine-tune and secure the height of the Leveling Feet and Adjustment Nuts once you place the unit in its final location.

3. From inside the Case, insert the Dust Port (3) in the hole in the rear of the Case and align the mounting holes in Dust Port’s flange with the holes in the rear of the Case. Secure with the four Small Pan-Head Screws (14) through the Case and into the tapped holes in the Dust Port’s flange. Do not fully tighten until all the screws are installed.

4. Attach the Right Edge Lip (4), Left Edge Lip (5) and Rear Edge Lip (6) to the Case (1) with three Lock Knobs (10) in each. Make sure that the folded edges of the Right and Left Edge Lips face outward and that the rounded corners are at the front of the unit. The Right and Left Edge Lips can be raised and lowered and the Back Edge Lip removed to accommodate workpieces of different sizes.

5. Attach the Handles (9) to the sides of the Case (1), using two Large Pan-Head Screws (13) for each handle

6. If they’re not already in place, fit the flexible Rubber Grommets (8) into the large holes in the Downdraft Plates (7). Place the Downdraft Plates in position on the Base (1).

7. Thread the Stopper Nuts (12) onto the Stopper Bolts (11). You will insert these in the Rubber Grommets in the Downdraft Plates to hold smaller workpieces and keep them from shifting.

8. Attach a 4" dust hose with hose clamp (not included) or other fitting to the Dust Port.

9. Place the unit where it will be used and adjust the Leveling Feet (2) as needed.

Holding your Workpiece The Right and Left Edge Lips (4 and 5) can be raised or lowered and the Back Edge Lip (6) removed to accommodate a variety of workpiece sizes, and the Stopper Bolts (11) and Nuts (12) can be used as a sort of bench dog to keep workpieces from shifting.

1. To use the Stopper Bolts (11) and Nuts (12) to hold a workpiece while you’re working on it, place the workpiece on the Downdraft Table and insert Stopper Bolts in the appropriate smaller holes in the Downdraft Plates. Fig. 1. Remove the workpiece, carefully lift the Downdraft plates and, from underneath, thread a Stopper Nut onto each Stopper Bolt. Then reinstall the Downdraft Plates in the Case.

2. If your workpiece won’t fit within the Downdraft Table, you can lower the Right and Left Edge Lip (4 and 5) and

remove the Back Edge Lip by loosening the Lock Knobs (10), making the adjustments and retightening the Lock Knobs.

Storing your Downdraft Table 1. Identify a wall location with enough space to fit the unit.

2. Drill a pilot hole and drive a 3/8" x 4" lag bolt (not included) into a wall stud. Make sure that the lag bolt is secure in the wall stud but also extends far enough from wall to account for the Leveling Feet.

3. Place the three Downdraft Plates (7) vertically inside the Case (1) for storage and hang the unit on the lag bolt, using the keyhole in the Case bottom. Fig. 2.

Check Rockler.com for updates. If you have further questions, pleasecontact our Technical Support Department at 1-800-260-9663 or support@rockler.com

Lag bolt must be driven into a wall stud to be able to support the weight of the Downdraft Table. Failure to do so could result in the Downdraft Table crashing down, potentially causing property damage and/or personal injury.

Fig. 1

Fig. 2