DOUBLE SPEED REMOTE CONTROL SYSTEM · DOUBLE SPEED REMOTE CONTROL SYSTEM Code Rev. Release ... srl...

DOUBLE SPEED REMOTE CONTROLSYSTEM

CodeRev.Release

MD.0.096004/03

USE/MAINTENANCE ANDSPARE PARTS MANUAL

srl

- Crane Fitting Directive – Instructions manual for double speed remote control -

- 1 -Via Mediterraneo, 6

42022 Boretto (R.E.) – ItalyTel.: +39 0522 963008 – Fax: +39 0522 963039

CONTENTS

1 INTRODUCTION page 2

2 INSTRUCTIONS page 2

3 DESCRIPTION OF MAIN COMPONENTS page 3

3.1 Electro-hydraulic manifold with actuators page 33.2 Electrical box with base connector page 43.3 Pendant page 53.3.1 Pendant functions page 5

4 USE OF THE CONTROLS page 6

4.1 Use of the crane through lever controls page 64.1.1 Crane version “H” (PTO driven) page 64.1.2 Crane version “E” (electric driven) page 6

4.2 Use of the crane through the remote control page 74.2.1 Crane version “H” (PTO driven) page 74.2.2 Crane version “E” (electric driven) page 7

4.3 Use of the crane in emergency (electrical failure) page 84.3.1 Crane version “H” (PTO driven) page 8

5 FAULTS – CAUSES – REMEDIES page 9

6 WIRING AND HYDRAULIC DIAGRAMS page 11

6.1 Hydraulic diagram crane version “H” (PTO driven) page 116.2 Hydraulic diagram crane version “E” (electric driven) page 126.3 Pendant wiring diagram page 136.4 Base connector wiring diagram crane version “E” (electric driven) page 136.5 Base connector wiring diagram crane version “H” (PTO driven) page 14

SPARE PARTS SECTION

TR.16.22.0 Double speed remote control page 1-2TR.16.23.0 Double speed hydraulic unit page 3

srl




1 INTRODUCTION

- This documentation was drawn up by Next Hydraulics, in order to inform the User about theprescriptions and the basic principles for the correct use of the REMOTE CONTROL SYSTEM.

- These instructions were drawn up for your safety and for the one of other peoples.Before using this device, always read carefully this manual, especially referring to safety prescriptions(paragraph 2) and to way of use (paragraph 4).

- It is very important that this instructions manual is kept together with the device for any future reading.Should the device be sold or transferred to somebody, make sure that the manual is suppliedtogether with it, so that the new user can be informed on device functioning.

- The user of this device is entrusted with its own safety and the one of peoples and things lying in itsworking area; therefore the user must have a detailed knowledge about its functioning.In case of any defect noticed, apply to the nearest Service Centre.

- The equipment must not be tampered for any reason.- Any attempt of modification of the installation, or tampering of whichever part of the equipment from

the user or from personnel not expressly authorized from the manufacturer, will invalidate relevantwarranty, and will release the manufacturer from every responsibility concerning possible damages tothings and peoples ensuing from such tampering.

NOTE

Next Hydraulics reserves the right to make changes to the product without prior notice forimprovement requirements.In case there are discrepancies between what described in this manual and the device in yourpossession, please apply to your supplier.

2 INSTRUCTIONS

- The use of the crane by remote control is allowed only to qualified and properly trained operators.- The operator, standing in a position of perfect visibility, is to make sure that the remote control allows

precise, controlled and repetitive load movements.- Never leave the pendant unguarded when the selection key is inserted, and never leave it exposed to

the atmospheric agents. Take away the pendant at the end of each working session, and recover it ina safe place.

- The female connector under the electrical box beside the valve bank must be protected with itsproper cover.

- Always check that the manoeuvres given through the remote control functions are correctly carriedout by the electro-hydraulic devices, especially concerning the following operating conditions:• The opening and re-positioning movements of the remote control levers are to be precise, stable

and repetitive• Every single operation of a valve bank function must not cause the starting, complete or partial, of

other functions.

ATTENTION

Always follow scrupulously the instructions and the general prescriptions for the use of liftingequipments mentioned in the MAXILIFT crane Use and Maintenance manual.

srl




3 DESCRIPTION OF MAIN COMPONENTS (Pict. 1)

The remote control system in object is made of an electro-hydraulic manifold (A), which is connected toan hydraulic valve bank with levers by means of proper actuators, connected to the cursors.The hydraulic block is run electrically by a 12 / 24 V DC system.

The electrical installation consists of:

• an electrical box (C), including the base connector and the wiring to the solenoid valves of thehydraulic manifold

• the remote control pendant (B) fitted with 8 meters cable and multipolar connector.

Pict. 1

3.1 ELECTRO-HYDRAULIC MANIFOLD WITH ACTUATORS (Pict. 2)

The directional electro-hydraulic manifold (A), which is connected to an hydraulic valve bank with levers,consists of an inlet and flow regulating section (1), and a section consisting of proper actuators (2),connected to the valve bank cursors.The inlet cross section performs the functions of selecting the way of control (remote or by valve bank),regulating the flow rate to the functions and supplying the actuators’ solenoid valves.

srl




The selection and flow regulation functions are operated either by ON-OFF or proportional cartridgesolenoid valves, depending upon the version of the controls.Some solenoid valves are fitted with manual operators for emergency operation in case of electricalfailure.The actuators (3) are essentially servo-pistons operating the valve bank spools.Each servo-piston is operated by two directional cartridge solenoid valves (4 A/B) 3 ways/2 positions forshifting the spool in both senses and inverting relevant movement.

3.2 ELECTRICAL BOX WITH BASE CONNECTOR (Pict. 2)

On the electrical box (C), which is connected to the battery, you can find the following components:a) a key-made selector (5) with 3 positions

central position: system out, the key can be removedposition TELE (remote): pendant activated and remote control ready to operateposition GRU (crane): remote control disconnected, the crane must be operated through the valvebank

b) a button (6) used for energizing the solenoid starter of the motor pump on the cranes with electro-hydraulic functioning (Vers. E – ERS). The button is not active on the cranes operated by PTO (Vers.H)

c) a multipolar base connector (7), for the connection of the pendant, complete of its protecting cover tobe used when the pendant connector is disconnected

d) the wiring to the directional solenoid valves (8), selector (9) and EV9 safety valve (only on vers. H).

Pict. 2

srl




3.3 PENDANT (Pict. 2)

The pendant (B) is the remote control device, made of a small plastic console, fitted with ergonomichandle for holding it with a single hand.On the front side there are the functions selectors (10), a green led indicating the presence of electricalsupply and a mushroom-head emergency button, which is also a main switch.On the handle there is the button for speed doubling (for ON-OFF version), or for speed regulation(proportional version).The pendant is fitted with a multipolar cable (11) of 8 mt. length, ending with a connector, to be engagedon its corresponding base placed on the electrical box beside the valve bank.

3.3.1 PENDANT FUNCTIONS (Pict. 3)

1 Emergency button (main switch)2 Warning light indicating supplied pendant3 Double speed button4 Crane slewing selector5 Boom raising selector6 Boom extension selector7 Winch selector (optional)

Pict. 3

srl




4 USE OF THE CONTROLS

4.1 USE OF THE CRANE THROUGH LEVER CONTROLS (Pict. 4)

4.1.1 CRANE VERSION “H” (PTO DRIVEN)

Set the key selector (1) into position "GRU" (crane), and operate from the control valve bank, as specifiedin the MAXILIFT Use and Maintenance manual.

4.1.2 CRANE VERSION “E” (ELECTRIC DRIVEN) (Pict. 4)

Set the key-made selector (1) into position "GRU" (crane), and operate from the control valve bank, thenpush the button (2) to start up the motor pump supplying the oil flow. Operate the crane from the valve bank, as specified in the MAXILIFT Use and Maintenance manual.

Pict. 4

srl




4.2 USE OF THE CRANE THROUGH THE REMOTE CONTROL

4.2.1 CRANE VERSION “H” (PTO DRIVEN) (Pict. 4)

• Set the key selector (1) into position "GRU" (crane), to operate from the control valve bank.• Stabilize the crane by deploying the stabilizer legs on the ground (see instructions given in the

MAXILIFT Use and Maintenance manual).• Using the valve bank, put the crane in a such position, that possible manoeuvring errors, when

activating the remote control, do not cause any harm to peoples, or damage to surrounding things.• Plug the pendant connector (3) into the base connector (4).• Select the remote mode, by turning the key (1) into “TELE” (remote) mode.• Unlock the mushroom-head emergency button (5) by turning it, in order to supply the pendant: the

warning led (6) will light up.• Always operate first the function selector (7), one function at a time: every function will work at low

speed. The push the button (8) to operate at full speed.• When terminated the operation, the crane must be recovered into travelling position. Turn the

pendant off by pushing the emergency button (5), remove the pendant and put it in a safe, protectedplace, covering the base connector (4) with its lid (9). Then turn the mode selector (1) into "GRU"(crane) mode, and recover the stabilizer extensions and legs.

• Turn the mode selector into neutral position, and remove the key (1).

4.2.2 CRANE VERSION “E” (ELECTRIC DRIVEN) (Pict. 4)

• Set the key selector (1) into position "GRU" (crane), to operate from the control valve bank, thenpush the button (2) to start up the motor pump supplying the oil flow.

• Stabilize the crane by deploying the stabilizer legs on the ground (see instructions given in theMAXILIFT Use and Maintenance manual).

• Using the valve bank, put the crane in a such position, that possible manoeuvring errors, whenactivating the remote control, do not cause any harm to peoples, or damage to surrounding things.

• Plug the pendant connector (3) into the base connector (4).• Select the remote mode, by turning the key (1) into “TELE” (remote) mode.• Switch the pendant on through the switch (5), the warning led (6) will light up.• Always operate first the function selector (7), one function at a time: every function will work at low

speed. The push the button (8) to operate at full speed.• When terminated the operation, the crane must be recovered into travelling position, turn the

pendant main switch (5) off, remove the pendant and put it in a safe, protected place, covering thebase connector (4) with its lid (9). Then turn the mode selector (1) into "GRU" (crane) mode, andrecover the stabilizer extensions and legs. When using the machine into "GRU" (crane) mode,always remember to push the button (2) simultaneously to the operation of the valve bank manuallevers.

• Turn the mode selector into neutral position, and remove the key (1).

srl




4.3 USE OF THE CRANE IN EMERGENCY (ELECTRICAL FAILURE)

4.3.1 CRANE VERSION “H” (PTO DRIVEN)

In case of electrical failure, the crane can be operated manually, even if only at low speed. It is necessaryto work the manual operator (1) of the solenoid valve (2) placed inside the control valve casing by pullingit and turning it by 180° at the same time, in order to keep it in position.Always remember to put the manual operator back to it original position (low), by carrying out theopposite movement to the above described one once restarting using the crane in normal conditions.

Pict. 5

srl




5 FAULTS - CAUSES – REMEDIES

Fault Cause Remedy

One of the functions does notwork.

• Relevant cartridge is jammedinto closed position.

• Relevant solenoid is notenergized.

• Relevant actuator is faulty.

• Clean or replace the cartridge.

• Check or replace the solenoid.

• Check and remove the fault.One of the functions is alwaysactivated simultaneously withothers.

• Relevant cartridge jammed intoopen position.


All functions are not operated withthe remote control, whilst fromvalve bank everything is regular.

• Pendant not switched on, ornot plugged into its connector.

• Remote control mode selector(1 – Pict. 4) not correctlychanged over (TELE – remote).

• Main supply fuse burnt.

• Check system’s supply andconnections.

• Check selector’s position andfunctionality.

• Check the fuse.Movements at full speed are tooslow.

• Low oil flow rate. Insufficient or inefficient pump.

• Check pump and pressure.

Movements at low speed are tooslow.

• Flow divider (SFC – Pict. 5) notcorrectly adjusted.

• Adjust the flow divider (SFC –Pict. 5) turning the screw (1).

Functions work only at low speed.

• Solenoid of the double speedvalve (39 – Pict. 5) notenergized.

• Double speed solenoid valvejammed.

• Check and replace in case.


Valve bank levers have difficultiesin moving – delay in movements.

• Oil too cold.

• Low pressure in the flowreduction valve.

• Hardened valve bank levers.• Low counter-pressure on the

outlet

• Operate for some time from thevalve bank.

• Ask Next Hydraulics’ ServiceDepartment.

• Grease or oil levers’ assembly.• Lead counter-pressure on the

outlet to 5 Bar.

You cannot operate by the controlvalve bank (stationary position).

• Mode selector not correctlychanged over in position GRU(crane).

• Button (2 – Pict. 4) not pushed(only for crane with motorpump).

• Check selector’s position andfunctionality.

• Push the button (2 – Pict. 4) tostart the motor pump.

ATTENTION

Some of the checking and repair interventions described above require a good knowledge level,and must be carried out by learned and skilled personnel.Unskilled personnel should not carry out any intervention.

srl




Pict. 6

srl




6 WIRING AND HYDRAULIC DIAGRAMS

6.1 HYDRAULIC DIAGRAM CRANE VERSION “H” (PTO DRIVEN)

• VC Counter-pressure valve• 39 Speed doubling solenoid valve 2 ways/2 pos.• SFC Flow divider• 9 Safety solenoid valve 2 ways/3 pos.• RPM Pressure regulator• FLT Filter• 1A-4B Functions control solenoid valves 3 ways/2 pos.

Pict. 7

srl




6.2 HYDRAULIC DIAGRAM CRANE VERSION “E” (ELECTRIC DRIVEN)

• VC Counter-pressure valve• 39 Speed doubling solenoid valve 2 ways/2 pos.• SFC Flow divider• RPM Pressure regulator• FLT Filter• 1A-4B Functions control solenoid valves 3 ways/2 pos.• G Plug

Pict. 8

srl




6.3 PENDANT WIRING DIAGRAM

Pict. 9

6.4 BASE CONNECTOR WIRING DIAGRAM CRANE VERS. “E” (ELECTRIC DRIVEN)

Pict. 10

srl




6.5 BASE CONNECTOR WIRING DIAGRAM CRANE VERS. “H” (PTO DRIVEN)

Pict. 11

DOUBLE SPEEDREMOTE CONTROL SYSTEM

SPARE PARTS SECTION

THIS SPARE PARTS CATALOGUE IS FOR THE MAXILIFT LOADER

INTRODUCTIONThe catalogue has several main suddivisions.Each of them embraces a main component groupping.Each illustration is followed by the corresponding written material. Parts shown in the illustrations arenumbered by position starting with number 1. This position number is listed with the written materialopposite the part number, quantity per loader and description of the appropriate part.

INTERPRETATION OF THE SIGNS FOR PAGE NUMBERS

130-350 TR.16.23.0 1

Lader type Plates Edition

ORDERING SPARE PARTS

When ordering spare parts please:1 -Include the part number, description and quantity desired.2 -Include your complete address.3 -Specify how the parts are to be sent.4 -List the desired parts in sequence by part number.5 -When ordering spare parts for one particular stabilizer, please always indicate the type

and the serial number. This information is given on a plate mounted on the main beam.

CE CATALOGUE EST POUR LES PIECES DE RECHANGE DU TYPE DEGRUE MAXILIFT

INTRODUCTIONCe catalogue a plusieurs subdivisions principaux. Chacune de ces subdivisions embrace unregroupement des composantes prinsipaux.Chaque illustration est suivie par le correspondant materiel écrit. Les pièces montrées dans lesillustrations sont nombrées à partir du number 1. Le nombre de position est dressé avec le materielécrit poosé au numero de la pièce, quantité par grue et description de la pertie convenable.

INTERPRETATION DES SYMBOLES POUR LES NUMBRES DES PAGES

POUR COMMANDER LES PIECES DE RECHANGE

Quand vous commendez les pièces de rechange:1 - Includez le numero de la pièce, sa description et la quantité désidérée.2 - Includez votre adresse complete.3 - Spécifiez comment les pièces doivent etre envoyées.4 - Spécifiez les pièces desirées en sequence avec le numero de la pièce.5 - Quand vous commandez les pièces de rechange pour une traverse particulière indiquez le typeet son numero de série. Cette information est indiquée sur la plaque placée sur la traverse

130-350 TR.16.23.0 1

Grue type Tableaux Edition

Pos. Codice Qt. Denominazione Description Désignation Benennung Denominaciòn

Via MEDITERRANEO, 6Boretto REGGIO E. - italy

Rev.TavolaMod.

130130130130130–––––350350350350350 05/0305/0305/0305/0305/03TR.16.22.0TR.16.22.0TR.16.22.0TR.16.22.0TR.16.22.0

COMANDO A DISTANZA 2 VELOCITA' COMANDO A DISTANZA 2 VELOCITA' COMANDO A DISTANZA 2 VELOCITA' COMANDO A DISTANZA 2 VELOCITA' COMANDO A DISTANZA 2 VELOCITA' – TWO SPEED REMOTE– TWO SPEED REMOTE– TWO SPEED REMOTE– TWO SPEED REMOTE– TWO SPEED REMOTECONTROL – TELECOMMANDE A DEUX VITESSES –CONTROL – TELECOMMANDE A DEUX VITESSES –CONTROL – TELECOMMANDE A DEUX VITESSES –CONTROL – TELECOMMANDE A DEUX VITESSES –CONTROL – TELECOMMANDE A DEUX VITESSES –

KABELPERN STEUERUNG ZWEI GESCHWINDIGKEITEN –KABELPERN STEUERUNG ZWEI GESCHWINDIGKEITEN –KABELPERN STEUERUNG ZWEI GESCHWINDIGKEITEN –KABELPERN STEUERUNG ZWEI GESCHWINDIGKEITEN –KABELPERN STEUERUNG ZWEI GESCHWINDIGKEITEN –TELECOMANDO DOS VELOCIDATESTELECOMANDO DOS VELOCIDATESTELECOMANDO DOS VELOCIDATESTELECOMANDO DOS VELOCIDATESTELECOMANDO DOS VELOCIDATES

Pagina

11111

1 DI.2.036 1 GRUPPO ATTUATORE 3F. ACTUATOR UNIT 3F GROUPE ACTIONN. 3F TRIEBGRUPPE 3F GRUPO ACTIONADOR 3F1A DI.2.037 1 GRUPPO ATTUATORE 4F. ACTUATOR UNIT 4F GROUPE ACTIONN. 4F TRIEBGRUPPE 4F GRUPO ACTIONADOR 4F2 DI.2.036/01 1 KIT SERVO PISTONE 3F. ASSIST PISTON KIT 3F KIT SERVOPISTON 3F SERVOKOLBENSATZ 3F KIT SERVOPISTON 3F2A DI.2.037/01 1 KIT SERVO PISTONE 4F. ASSIST PISTON KIT 4F KIT SERVOPISTON 4F SERVOKOLBENSATZ 4F KIT SERVOPISTON 4F3 NI.1.003 2 NIPPLO NIPPLE NIPPLE NIPPLE NIPLE4 TF.2.023 2 TUBO FLESSIBILE HOSE TUYAU FLEXIBLE SCHLAUCH TUBO FLEXIBLE5 TA.1.022 2 TAPPO CAP BOUCHON VERSCHLUSS TAPON6 RA.1.056 2 DADO NUT ECROU MUTTER TUERCA7 RA.1.105 4 RACCORDO FITTING RACCORD FITTING RACORD8 TU.0.132 1 TUBO RIGIDO PIPE TUBE RIGIDE STARRES ROHR TUBO RIGIDO9 TU.0.133 1 TUBO RIGIDO 3F. PIPE TUBE RIGIDE STARRES ROHR TUBO RIGIDO9A TU.0.134 1 TUBO RIGIDO 4F. PIPE TUBE RIGIDE STARRES ROHR TUBO RIGIDO

1011 SN.0.013 1 SOLENOIDE 12V SOLENOID 12V RELAIS 12V RELAIS 12V CONTACTOR 12V11A SN.0.014 1 SOLENOIDE 24V SOLENOID 24V RELAIS 24V RELAIS 24V CONTACTOR 24V12 CN.1.004 2 CONNETTORE CONNECTOR CONNECTEUR VERBINDER CONECTOR13 SN.0.015 1 SOLENOIDE 12V SOLENOID 12V RELAIS 12V RELAIS 12V CONTACTOR 12V13A SN.0.016 1 SOLENOIDE 24V SOLENOID 24V RELAIS 24V RELAIS 24V CONTACTOR 24V14 SN.0.019 1 SOLENOIDE COM. 12V SOLENOID 12V RELAIS 12V RELAIS 12V CONTACTOR 12V14A SN.0.020 1 SOLENOIDE COM. 24V SOLENOID 24V RELAIS 24V RELAIS 24V CONTACTOR 24V15 IT.0.007 1 INTERRUT. A CHIAVE SWITCH INTERRUPTEUR SCHALTER INTERRUPTOR16 PS.0.041 1 PULSANTE BUTTON BOUTON DRUCKKNOPF PULSADOR17 CN.1.006 1 CONNETTORE CONNECTOR CONNECTEUR VERBINDER CONECTOR18 CN.1.006/01 1 CONNETTORE CONNECTOR CONNECTEUR VERBINDER CONECTOR19 CN.1.006/02 1 COPERCHIO COVER COUVERCLE DECKEL TAPA20 CN.1.007 1 CONNETTORE CONNECTOR CONNECTEUR VERBINDER CONECTOR21 CN.1.007/01 1 CONNETTORE CONNECTOR CONNECTEUR VERBINDER CONECTOR22 CV.0.035 8 m CAVO CABLE CABLE ELEKTROKABEL CABLE23 PS.0.035/01 4 SELETTORE SWITCH SELECTEUR WAHLSCHALTER24 PS.0.042/05 1 CORPO PULSANTIERA PLASTIC BOX CORPS BOITIER GEHAUSE CAJA PANEL DE MANDOS25 PS.0.042/02 1 PULSANTE D’EMERGENZA PUSH BUTTON BOUTON DRUCK BOTON



Rev.TavolaMod.

130130130130130–––––350350350350350 05/0305/0305/0305/0305/03TR.16.22.0TR.16.22.0TR.16.22.0TR.16.22.0TR.16.22.0

COMANDO A DISTANZA 2 VELOCITA' COMANDO A DISTANZA 2 VELOCITA' COMANDO A DISTANZA 2 VELOCITA' COMANDO A DISTANZA 2 VELOCITA' COMANDO A DISTANZA 2 VELOCITA' – TWO SPEED REMOTE– TWO SPEED REMOTE– TWO SPEED REMOTE– TWO SPEED REMOTE– TWO SPEED REMOTECONTROL – TELECOMMANDE A DEUX VITESSES –CONTROL – TELECOMMANDE A DEUX VITESSES –CONTROL – TELECOMMANDE A DEUX VITESSES –CONTROL – TELECOMMANDE A DEUX VITESSES –CONTROL – TELECOMMANDE A DEUX VITESSES –

KABELPERN STEUERUNG ZWEI GESCHWINDIGKEITEN –KABELPERN STEUERUNG ZWEI GESCHWINDIGKEITEN –KABELPERN STEUERUNG ZWEI GESCHWINDIGKEITEN –KABELPERN STEUERUNG ZWEI GESCHWINDIGKEITEN –KABELPERN STEUERUNG ZWEI GESCHWINDIGKEITEN –TELECOMANDO DOS VELOCIDATESTELECOMANDO DOS VELOCIDATESTELECOMANDO DOS VELOCIDATESTELECOMANDO DOS VELOCIDATESTELECOMANDO DOS VELOCIDATES

Pagina

22222

26 PS.0.027 1 PULSANTE . BUTTON BOUTON DRUCK. BOTON27 PS.0.035/02 1 FRONTALINO COVER COUVERCLE DECKEL TAPA28 LS.0.008 1 SPIA VERDE GREEN LED LED VERT GRUNE LED LED VERDE29 PS.0.035 1 PULSANTIERA COMPL. CONTROL BOX TABLEAU POUSSOIRS DRUCKKNOPFTAFEL PANEL DE CONTROL30 16.5.009 1 SCATOLA BOX BOITE KASTEN CAJA31 16.5.010 1 COPERCHIO COVER COUVERCLE DECKEL TAPA32 VT.0.008 2 VITE SCREW VIS SCHRAUBE TORNILLO33 DA.1.006 4 DADO NUT ECROU MUTTER TUERCA34 VT.5.001 2 VITE SCREW VIS SCHRAUBE TORNILLO35 DA.1.004 4 DADO NUT ECROU MUTTER TUERCA36 DA.1.005 16 DADO NUT ECROU MUTTER TUERCA37 BF.0.013 0.25 BARRA FILETTATA THREADED ROD BARRE FILETEE GESCHN. STAB BARRA FILETEADA38 NI.1.002 4 NIPPLO NIPPLE NIPPLE NIPPLE NIPLE39 RO.7.001 4 RONDELLA WASHER RONDELLE UNTERLEGSCHEIBE ARANDELA40 TC.2.007 1 BASE CONNETT. 3F 12V CONNECT. BASE 3F 12V BASE CONNECT. 3F 12V VERBINDERBASIS 3F 12V BASE CONECT. 3F 12V40A TC.2.009 1 BASE CONNETT. 4F 12V CONNECT. BASE 4F 12V BASE CONNECT. 4F 12V VERBINDERBASIS 4F 12V BASE CONECT. 4F 12V40B TC.2.008 1 BASE CONNETT. 3F 24V CONNECT. BASE 3F 24V BASE CONNECT. 3F 24V VERBINDERBASIS 3F 24V BASE CONECT. 3F 24V40C TC.2.010 1 BASE CONNETT. 4F 24V CONNECT. BASE 4F 24V BASE CONNECT. 4F 24V VERBINDERBASIS 4F 24V BASE CONECT. 4F 24V



Rev.TavolaMod.

130130130130130–––––350350350350350 05/0305/0305/0305/0305/03TR.16.23.0TR.16.23.0TR.16.23.0TR.16.23.0TR.16.23.0

1 DI.2.036/07 1 CORPO REGOLAZIONE ADJUSTMENT BODY CORPS DE REGLAGE REGELUNGSKÖRPER CUERPO DE REGLAJE2 DI.2.036/06 1 CORPO LATERALE SIDE BODY CORPS LATERAL SEITENKÖRPER CUERPO LATERAL3 DI.2.036/05 1 CORPO 3 FUNZIONI 3 FUNCTIONS BODY CORPS 3 FONCTIONS 3 FACH KÖRPER CUERPO 3 FUNCIÓNES3A DI.2.037/02 1 CORPO 4 FUNZIONI 4 FUNCTIONS BODY CORPS 4 FONCTIONS 4 FACH KÖRPER CUERPO 4 FUNCIÓNES4 DI.2.036/03 1 VALVOLA VALVE SOUPAPE VENTIL VALVULA5 DI.2.011/03 1 DIVISORE DI FLUSSO VALVE SOUPAPE VENTIL VALVULA6 DI.2.036/02 1 VALVOLA DI MASSIMA VALVE SOUPAPE VENTIL VALVULA7 VT.1.011 4 VITE SCREW VIS SCHRAUBE TORNILLO8 DI.2.041 1 VALVOLA VALVE SOUPAPE VENTIL VALVULA9 DI.2.042 8 VALVOLA VALVE SOUPAPE VENTIL VALVULA

10 DI.2.036/04 1 VALVOLA VALVE SOUPAPE VENTIL VALVULA11 DI.2.036 1 GRUPPO ATTUATORE 3F. ACTUATOR UNIT 3F GROUPE ACTIONN. 3F TRIEBGRUPPE 3F GRUPO ACTIONADOR 3F11A DI.2.037 1 GRUPPO ATTUATORE 4F. ACTUATOR UNIT 4F GROUPE ACTIONN. 4F TRIEBGRUPPE 4F GRUPO ACTIONADOR 4F

GRUPPO IDRAULICO 2 VELOCITA' GRUPPO IDRAULICO 2 VELOCITA' GRUPPO IDRAULICO 2 VELOCITA' GRUPPO IDRAULICO 2 VELOCITA' GRUPPO IDRAULICO 2 VELOCITA' – TWO SPEED HYDRAULIC– TWO SPEED HYDRAULIC– TWO SPEED HYDRAULIC– TWO SPEED HYDRAULIC– TWO SPEED HYDRAULICUNIT – GROUPE HYDRAULIQUE A DEUX VITESSES –UNIT – GROUPE HYDRAULIQUE A DEUX VITESSES –UNIT – GROUPE HYDRAULIQUE A DEUX VITESSES –UNIT – GROUPE HYDRAULIQUE A DEUX VITESSES –UNIT – GROUPE HYDRAULIQUE A DEUX VITESSES –

HYDRAULISCHER GRUPPE ZWEI GESCHWINDIGKEITEN –HYDRAULISCHER GRUPPE ZWEI GESCHWINDIGKEITEN –HYDRAULISCHER GRUPPE ZWEI GESCHWINDIGKEITEN –HYDRAULISCHER GRUPPE ZWEI GESCHWINDIGKEITEN –HYDRAULISCHER GRUPPE ZWEI GESCHWINDIGKEITEN –GRUPPO HIDRAULICO DOS VELOCIDATESGRUPPO HIDRAULICO DOS VELOCIDATESGRUPPO HIDRAULICO DOS VELOCIDATESGRUPPO HIDRAULICO DOS VELOCIDATESGRUPPO HIDRAULICO DOS VELOCIDATES

Pagina

33333

NEXT HYDRAULICS S.r.l.Via Mediterraneo 6

42022 BORETTO (Reggio E.) - ItalyTel.: +39 0522 963008 – Fax.: +39 0522 963039

e-mail: [email protected]

DOUBLE SPEED REMOTE CONTROL SYSTEM · DOUBLE SPEED REMOTE CONTROL SYSTEM Code Rev. Release ... srl...

Documents

Transcript of DOUBLE SPEED REMOTE CONTROL SYSTEM · DOUBLE SPEED REMOTE CONTROL SYSTEM Code Rev. Release ... srl...