Doors K · doors are more secure against forced entry. • Maximum reliability by means of: - a...

Waregemstraat 5 - 9870 Zulte - BelgiumTel +32 9 388 88 81 - Fax +32 9 388 88 21

[email protected] - www.sobinco.com

MULTI-POINT LOCKS SERIES 80000K.08Doors

Contents

1. General K.08.021.1. Description and advantages1.2. Technical characteristics

2. Multi-pointlockwithstandardlatchbolt K.08.04

3. Turningandreplacingthelatchbolt K.08.05

4. Otherlatchbolts K.08.05

5. Short(K)andlong(L)multi-pointlocks K.08.07

6. Shortkeeps K.08.086.1. General6.2. With U-shaped faceplate6.3. With flat faceplate

7. Longkeeps K.08.107.1. With U-shaped faceplate7.2. With flat faceplate7.3. Shorter (K) and longer (L) version

8. Casesinsyntheticmaterialforflatkeeps K.08.13

9. Electricdooropener K.08.149.1. General characteristics9.2. Installation on faceplate9.3. Order codes9.4. Types and function

10.Sectionpreparationsforlocks K.08.17

11.Sectionpreparationsforkeeps K.08.18

03-04-2012

MULTI-POINT LOCKS SERIES 80000

Waregemstraat 5 - 9870 Zulte - Belgium - www.sobinco.com Tel +32 9 388 88 81 - Fax +32 9 388 88 21 - [email protected] K.08.02

1. General1.1. Descriptionandadvantages

• The multipoint lock is provided with top and bottom lock with an upward hook bolt and 2 security pins so that your doors are more secure against forced entry.

• Maximum reliability by means of: - a renewed latch bolt mechanism - a renewed handle mechanism - not disengageable gear wheels: that’s why the lock can not be forced during the working activities on the build-ing site.

• The 3 hook bolts are pivoting, rather than sliding. They are therefore longer than conventional bolts, so there is the same proportion of the dead bolt within the lock case as is engaged into the frame, making it extremely dif-ficult for burglars to force entry by means of a crowbar.

• The hook bolts ensure security in horizontal direction, the pins in vertical direction. The upward hook bolts also serve as anti-lift security.

• The lock has special tapered top and bottom dead bolts which pull the vent section against the frame when lock-ing the door, to provide an effective weather seal. Also a slightly deformed door (for example due to extreme weather conditions) can be closed without having to force the key.

• Two holes above and below the handle opening allow the door handles to be screwed to each other through the lock, so there are no screws visible from the outside.

• The lock can be used left hand and right hand simply by turning the latch bolt.

• The latch bolt can be operated by the door handle as well as by the key.

• The lock can only be supplied with standard latch bolt. The latch bolt is interchangea-ble after installation with an easy operation. This is a very big advantage as you have to keep only 1 lock in stock. The other latch bolt types can be ordered separately.

• Locking and unlocking by a single turn of 360° with the cylinder key.

• Small turn moment when operating the latch bolt and when locking and unlocking the dead bolts.

• The vertical free margin (4 mm above and 6 mm below) between dead bolts and lock keeps should be sufficient in order to avoid the following problems: - dropping of the door - wrong vertical installation of the keep and/or lock

Centre lock

03-04-2012



1.2. Technicalcharacteristics

• The lock is available in 3 lengths: - Short version (K): 1895 mm - Standard version: 2170 mm - Long version (L): 2470 mm

• Available in 3 backsets: - 30 mm - 35 mm - 40 mm

• Faceplates: - Flat faceplate: 16 mm, 20 mm and 24 mm - U-shaped faceplate: 22x6.5 mm, 24x5 mm and 24x6.5 mm

• Very narrow lock: lock case width = 15.5 mm.

• The latch bolt is available in 5 different versions: - standard latch bolt - extended latch bolt - narrow latch bolt - roller bolt - cover plate (lock with only dead bolt)

• The lock is entirely made of non-corroding materials: - faceplate: stainless steel AISI 304 (austenitic) - lock cases: zinc alloy - latch bolt: zinc alloy nickel plated - dead bolts: zinc alloy nickel plated - pins: stainless steel AISI 303 (austenitic)

• The locks have been tested by SKG in the Netherlands. Twostarsare awarded to the locks in accordance with the star rating indicated in the KOMO certificate of SKG.

Top and bottom lock

03-04-2012



2. Multi-point lock with standard latch bolt

Flatfaceplate

U-shapedfaceplate

Ordercode A(mm) B(mm) C(mm)

80000-16-30 27 29.5 1680000-16-35 32 34.5 1680000-16-40 37 39.5 1680000-20-30 27 29.5 2080000-20-35 32 34.5 2080000-20-40 37 39.5 2080000-24-30 27 29.5 2480000-24-35 32 34.5 2480000-24-40 37 39.5 24

Indication line

The indication line serves as reference point for the lock position in relation to the keep position.

Ordercode A(mm) B(mm) C(mm) D(mm)

80000-U22-25 22.5 29 22 6.580000-U22-30 27.5 34 22 6.580000-U22-35 32.5 39 22 6.580000-U24-25 22.5 29 24 6.580000-U24-27 24 29 24 580000-U24-30 27.5 34 24 6.580000-U24-32 29 34 24 580000-U24-35 32.5 39 24 6.580000-U24-37 34 39 24 5

03-04-2012



3. Turning and replacing the latch bolt

Turningthelatchbolt Changingthelatchbolt

• Left hand and right hand lock.• Put the dead bolt (B) in closed

position.• Pull the latch bolt (A) forwards with

a pair of pliers and turn 180°.• Move the latch bolt backwards.

4. Other latch boltsCoverplateforlock Narrowlatchbolt Extendedlatchboltwithonlydeadbolt

• Set n° 80001 (1 piece)• Set n° G80001 (20 pieces)

• Put the dead bolt (B) in closed position.• Pull the latch bolt (A) forwards with a pair of pliers and

turn 90°.• Remove the latch bolt from the lock.• Position the new latch bolt horizontally.• Turn the latch bolt 90° to move the latch bolt backwards.



03-04-2012



Rollerbolts

Orderinformation

• The latch bolt sets contain: - the latch bolt - the installation instructions

• The roller bolt sets contain: - the roller bolt - the spring with length in accordance with the backset - the adjustment screw with length in accordance with the backset - the installation instructions

• When you require a lock with one of these latch or roller bolts, then you order a lock with standard latch bolt (see page K.08.04) in combination with the required latch or roller bolt set.

• The advantage is that you don’t have to take all the lock types in stock.

• Order example: lock with flat faceplate 20 mm and backset 35 mm with roller latch: - Lock n° 80000-20-35 - Roller bolt set n° 80003-2

Set Setcode1piece

Setcode20pieces Backset

80003-1 G80003-1 30 mm

80003-2 G80003-2 35 mm

80003-3 G80003-3 40 mm

03-04-2012



5. Short (K) and long (L) multi-point locks

• Both locks with flat as well as U-shaped faceplate are available in a shorter or longer version: the distance between the centre lock and the top lock is small-er or bigger than in case of the standard lock.

• K-version:- Toplockis275mmlowercom-paredtothestandardlock.

- 1 fixing hole less compared to the standard version.

• L-version:- Top lock is 400 mm highercomparedtothestandardlock.

- 1 fixing hole more compared to the standard version.

• Order codes:- Short: 80000-(U)..K-..- Long: 80000-(U)..L-..

Shortlock Longlock

(-275mm)

(+400mm)

03-04-2012



6. Short keeps6.1. General

• The short keeps are provided with a stainless steel faceplate in AISI 304.

• The centre keep is also provided with an indication line to check the keep position in relation to the lock position.

• Profile preparations: see page K.08.18.

6.2. WithU-shapedfaceplate

• The U-shaped faceplate is 22 mm wide and 5.5 mm, 8.5 mm or 11 mm high.

• The top and bottom keep is provided with a zinc alloy case.

• The encased keeps give a neat appearance and keeps the frame section free from dirt.

• The top and bottom keeps are horizontally adjustable by means of eccentric rollers which move the zinc alloy cases. The adjustment range is +/-1.5 mm.

• The centre keep is provided with a latch plate for the latch bolt opening. This latch plate can be removed to use the keep in combination with an electric door clos-er: see page K.08.15. This way, the same keeps can be used.

• The keeps have been tested by SKG in the Neth-erlands. Twostars are awarded to the keeps in accordance with the stars indication with relation to the KOMO certificate of SKG.

Indication line

Ordercode

Faceplate height E

Centreright

Centreleft

Top andbottom

5.5 mm 85111-U22R 85111-U22L 85121-U228.5 mm 85112-U22R 85112-U22L 85122-U2211 mm 85113-U22R 85113-U22L 85123-U22

Right hand Left hand

03-04-2012



6.3. Withflatfaceplate

• The faceplates are 22 mm wide and 2.5 mm high.

• The keeps are horizontally adjustable by means of ec-centric rollers. Adjustment range: +/-2 mm.

• The centre keep n° 85110-22R (L) is provided with a latch plate for the latch bolt opening. This latch plate can be removed to use the keep in combination with an electric door closer: see page K.08.15. This way, the same keeps can be used.

• The indication line serves as reference point for the keep position in relation to the lock position.

Indication lineOrdercode

Type Centre Top/bottomStandard 85010-22

85020-22With latch plate 85110-22R or L

Righthand

Lefthand

With latch plateWithout latch plate

03-04-2012



7. Long keeps7.1. WithU-shapedfaceplate

• General: see page K.08.08.

• Same characteristics as the sepa-rate zinc alloy keeps with stainless steel U-faceplate.

• The top and bottom keeps are horizontally adjustable by means of eccentric rollers which move the zinc alloy cases. The adjustment range is +/-1.5 mm.

• The keeps have been tested by SKG in the Netherlands. Twostars are awarded to the keeps in accordance with the stars indi-cation with relation to the KOMO certificate of SKG.


Left hand = illustratedRight hand = opposite view

Indication line

Ordercode

Faceplate height E Right hand Left hand

5.5 mm 85101-U22R 85101-U22L8.5 mm 85102-U22R 85102-U22L11 mm 85103-U22R 85103-U22L

03-04-2012



7.2. Withflatfaceplate

• Same characteristics as the separate stainless steel keeps with flat faceplate.

• The keep n° 85100-22R (L) is provided with a latch plate for the latch bolt open-ing. This latch plate can be removed to use the keep in combination with an elec-tric door closer: see page K.08.15. This way, the same keeps can be used.


Left hand = illustratedRight hand = opposite view

Indication line

Adjustment range

Type Ordercode

Standard 85000-22With latch plate 85100-22R or L

03-04-2012



7.3. Shorter(K)andlonger(L)version• Both long keeps with flat faceplate as well as with U-shaped faceplate, are available in a shorter or longer

version. In case of the L version there’s 1 additional fixing hole.

Ordercode

Faceplate height E Short Long5.5 mm 85131-U22R or L 85141-U22R or L8.5 mm 85132-U22R or L 85142-U22R or L11 mm 85133-U22R or L 85143-U22R or L

WithU-shapedfaceplate Withflatfaceplate

Ordercode

Type Short LongStandard 85030-22 85040-22With latch plate 85130-22R or L 85140-22R or L

Short Long Short Long

03-04-2012



8. Cases in synthetic material for flat keepsGeneral

• Cases in synthetic material which are mounted in the profile cut-out.

• To apply in combination with the short version as well as with the long version of the flat keeps.

• The case gives a neat appearance and keeps the frame section free from dirt.

Installation

• Hook in the upper side of the case behind the profile wall.• Slide the case and position together with the keep.• Fix the keep.

Centren° 85014

Top and bottomn° 85024

03-04-2012



9. Electric door opener9.1. Generalcharacteristics

• Small electric strike incorporating a space-saving locking flap, especially developed for installation in aluminium doors.

• The flap rotates back within the keep when operated. Big advantage: the cut-out is much smaller making the installation aesthetically pleasing.

• Break-in resistance of strike: 3750 N.

• Width adjustment of the locking flap: 3 mm.

• The electric strikes are non-handed.

Mechanicalrelease Resetbutton Electrical(typeE) connection

• Quick and simple electrical connection.

• The reset button is only possible for type 128 where the strike is held in the release position until the door has been opened.

• This button resets the electric strike when the door opens.

• The release button (type E) allows to suspend temporarily the auto-matic locking upon closing the door.

• Only available for type 128.

Reset button

Electrical connection

Release button

Adjustment range

03-04-2012



9.2. Installationonfaceplate

• For both short as long keeps.

• In order to be able to use an electric strike, a keep with latch plate must be provided.

• Method: - Remove the latch plate. - Mount and fix the electric strike with the same screws.

KeepswithU-faceplate Keepswithflatfaceplate

9.3. Ordercodes

• The following electric strikes are available:

• For more information about the types: see next page.

Ordercode Voltage Note

787-118 10-24V AC/DC787-128 10-24V AC/DC788-128E 10-24V AC/DC With release button787-138-12 12V DC787-138-24 24V DC

03-04-2012



9.4. Typesandfunction

Type118

• The door is only unlocked when you push a button. After releasing the button the door is locked again.

• This type works on 10-24V AC/DC and may be permanently connected to electrical cur-rent until 12V.

• This type is not possible with release button. This can be solved electronically by a switch.

• Note: when the door is pushed open by the gaskets, the door can still be open after re-leasing the button. This can be arranged by mounting a door closer on the door.

Type128

• On releasing the electric strike, for example, from a button on an intercom system, the strike is held in the release position until the door has been opened.

• The electric strike resets when the door opens. This means there is no need to rush through the door.

• This type works on 10-24V AC/DC and may be permanently connected to electrical current until 12V.

• This type is available with release button (version E). The release button allows to suspend temporarily the automatic locking upon closing the door.

Type138

• This type works on 12V DC or 24V DC and may be permanently connected to electrical current.

• The electric strike is mainly used in combina-tion with an alarm system. This means that for example in case of a power failure the door can be opened.

Electric strike

Door

Operation

Electric strike

Door

Operation

Electric strike

Door

Operation

03-04-2012



10. Section preparations for locks

• The indication line serves as reference point for the lock position in relation to the keep position.

Locktype A(mm) B(mm) C(mm) D(mm)

Standard 245 0 245 540Short (K) 215 0 0 265Long (L) 245 400 245 940

Indication line

R = Height reference

Frame Vent

03-04-2012



11. Section preparations for keeps

• The preparations count for: - short keeps - long keeps - U-shaped faceplate - flat faceplate - with electric strike

• The fixing holes G are not necessary in case of short (separate) keeps.

• Long keeps: see table.

• The indication line serves as ref-erence point for the keep position in relation to the lock position.

Keeptype A(mm) B(mm) C(mm)

Standard 282.5 0 282.5Short (K) 145 0 145Long (L) 282.5 400 282.5

Indication line

Frame Vent

R = Height reference

Doors K · doors are more secure against forced entry. • Maximum reliability by means of: - a...

Documents

Transcript of Doors K · doors are more secure against forced entry. • Maximum reliability by means of: - a...