www.PyleUSA.com www.PyleUSA.com

Start keyIndicator

light

Charging poles

Ground detectsensorsFrontwheel

Side brush

Suction inlet

Ground detect sensors

Driving wheel

Power switch

Back infraredreceiver

Surface cover

Dustbin

Side detect sensors

Front sensor window

Front infrared receiver

COMPONENTS OF THE PRODUCT

• Before using the product, please take out two side brushes from the package and assemble them onto the bottom of the product softly according to this installation diagram.

CONTENT

CONPONENTS OF THE PRODUCT IMPORTANT NOTICE 1. Guidelines for safe use 2. Notes for charging 3. Applicability

PRODUCT USE1. Charging of main body2. Power on/operating/pause/power o� 3. Cleaning mode4. Assemble mop

MAINTENCE 1. Brush cleaning2. Dustbin Cleaning3. Wheels and sensor windows cleaning

FAILURE CHECKING1. Alarming notice2. Notice

PARAMETER

01

www.PyleUSA.com www.PyleUSA.com

IMPORTANT NOTICE

GUIDELINES FOR SAFE USE

NOTES FOR CHARGING

APPLICABILITY

Please read the following safety instructions and follow all normal safety precautions carefully before using this product. Any operation unconformable to this manual may result in damage of the product.

• Please remove fragile items and items that may entangle side brush and suction channel (e.g.wire and curtain) on the �oor before use.• Don't stand or squat on this product, to avoid damage of the machine.• Please turn off the power switch at the bottom of the machine when not in use for a long period of time• Please remove the wasted battery off the machine for safe recycling before the product is out of service.• Any technician except for technicians specified by our company shall disassemble, maintain and modify the product.

• Use only the power cords and power adapters supplied by the product manufacturer. Using different power cords and adapter may damage the product• The power shall be supplied in accordance with the voltage indicated on the nameplate of the power adapter.• Do not use the device if the plug of the power adapter is damaged• Unplug the power cord if the machine is not to be used for a long period of time

• The product is applicable to dry and flat ground indoors, such as hardwood, ceramic tile etc.• Please don' t use this product in humidity (such as the bathroom).• Please don' t use this product outdoors.

Power & charging indicator lightInfrared transmit window

Charging adaptor socketCharging poles

DOCKING STATION

DOCKING STATION CHART INDICATOR LIGHT

DOCKING STATION STATUS INDICATOR LIGHT

Connect with adaptorConnect with main body

Red light keeps onBlue light �ashes

REMOTE CONTROL

• Press this key whencleaner is working, will enter standby mode

• Enter auto charging mode

• Press this key, cleaner goes forward

• Press this key, cleaner goes backward

• Press this key, cleaner goes left

• Press this key, cleaner goes right

• Press this key, when cleaner is working, will enter standby mode

• Press this key, cleaner will enter auto clean mode

• Press this key, cleaner will enter spot clean mode

• Press this key, cleaner will enter edge clean mode

• Press this key, cleaner will enter Z mode

• Press this key, cleaner will enter left spiral mode

• Press this key, cleaner will enter right spiral mode

• Before using the remote control, please take out the plastic piece that insulate the battery before power on.• Battery type is CR2032, +3V button battery.• Don' t use the remote control near the docking station.

Notes:

0302

www.PyleUSA.com www.PyleUSA.com

PRODUCT USE

CHARGING OF MAIN BODY

POWER ON / OPERATING / PAUSE / POWER OFF

CHARGING STATUS DOCKING STATION MAIN BODYChargingstatuschart

Before charging The red lights on The orange light Is on (low battery)

During charging The blue light flashes The green light Hashes

Fully charged The blue light flashes The green light keeps on

• Notes:1. Please make sure the docking station is connected well with the adapter.2. If you will not use the cleaner for a long time, please fully charge the cleaner and tum off. Please charge the cleaner every 3 months to avoid over discharge of the battery.

• PoweronPower on the main body by turning on the power switch and the main body will be in standby mode.

• Put the auto charging docking station in place and connect the adapter. The red power indicator light on the auto charging docking station keeps on.Notes: Place the docking station along the wall. Noobstacle or hollow areas 2m away from the docking Station in front and 0.5 on the left and right (Refer to Figure)• The following three methods can be used to charge the main body.A: Automatic return When the machine is low battery at work, the orange indicator light will be on and a buzzer will alarm the low battery, then the machine will enter the state of looking for the docking station and match the docking station automatically for charging.B: Arti�cial selection When the main body is in standby state or working, press the Docking key, the main body will search for the docking station for chargingC: Manual operation Place the main body on the auto charging docking station manually. Pay attention to the well contact between the charging pole pieces at the bottom of main body and the charging pole pieces of docking station.

• Operating: Operate the machine by pressing the start key on the robot, it will enter working state.• Pause: Pressing the start key on the robot, it will pause and enter standby state• Power off: Turn off the power switch of the main body, robot is powered off.

CLEANING MODE

In order to adapt to different ground environment and achieve more thorough cleaning, the main body is equipped with various cleaning modes.• Auto cleaning modePress the key on the main body, or the Auto clean key on remote control, the main body will enter Z mode, and in specific situation, it will enter edge cleaning mode.• Spot cleaning modePress Spot clean on remote control, the main body will enter spiral mode of cleaning in a range of about 1 m2 area, and will stop after 2 minutes of cleaning.• Edge cleaning modeThe robot will clean along the wall under this mode, and will enter auto clean mode when finish edge cleaning.• Spiral cleaning modeThe robot will clean in left or right spiral clean mode, and will enter auto clean mode when finish spiral cleaning.

Velcro

ASSEMEMBLE THE MOP

• If you need to use the mopping function, please take out the mop and stick it on the bottom of the main body as per picture.Remark:Make sure the mop is stuck smoothly and aligned, the mop is for dry mopping only, avoid using liquid.

0504

www.PyleUSA.com www.PyleUSA.com

MAINTENANCE

BRUSH CLEANING

FAILURE CHECKING

ALARMING NOTICE

DUSTBIN CLEANING

WHEELS AND SENSOR WINDOWS CLEANING

MOP CLEANING

• Please timely clean the brushes when the robot is dirty. Please pull out the brushes for cleaning is needed. Change the brush if it has damage

• Please timely clean the dustbin and inner filter after the robot is done cleaning. (if you wash the filter, please dry it first before using it again.)

• Notes:1. Please carefully check the sucking port if clean or not after pulling out the dustbin.2. The filter net can be washed, please dry it first and before using it again.

• Piease timely clean the wheels and sensor windows.

• Use the dry mopping function, when the mop is dirty, please take off the mop and wash in water then dry it for future use.Remark:Remove the mop carefully to prevent damaging the velcro at the bottom of the cleaner

The robot will give warning tone every 10 seconds when it comes to malfunction.

WARNING TONE FAILURE CAUSE SOLUTIONInfrared detectingsystem problem

Motor problemPower of the robot is limited

Left and right wheel problem

Other problems

Clean the wheel and ground sensor windows

Clean the inlet and outlet of motorPlease charge the robotPlease clean the wheel

Please contact service center

Notes:• Turn off the robot first and reopen the robot for checking if the above cases can't help you.• Please contact service center if the above cases and rebooting can't help you.• Turn off the robot when you're not using it

PARAMETER

ITEM PARAMETER DOCKING STATION

Rated voltageRated powerBattery capacity

Working time

Specification

G.W.Dustbin capacityOperating temperature range

Operating humidity range

Charging timeInput rating of adaptorOutput rating of adaptor

11V15W

2200mAh90-120 mins

330*300*63mm(including wheel height)

2.0Kg

0.35L32°F-113°F

S85%RH3-4H

100-240V AC 50/60HzDC 19V0.94A

REMOTE CONTROL

Input voltage: DC 19V0.94A

Output voltage: DC 19V0.94A

Battery:CR2032,+3.0V

0706