DNC for Fanuc 0M y 0T
3
www.connectcnc-dnc.com DNC / file transfer settings for Fanuc 0M and OT Set the following parameters on the machine: To set the CNC up for drip feed (0M): Enable parameter G127.5 Select AUTO (DNC) mode Send the program from the computer, then press Cycle Start on the Fanuc. To pause dripfeed, turn the Feedrate override to 0%. Set ConnectCNC as follows: Parameter Value 0002 00000001 0552 9 TV ON 0 ISO 1 I/O 0 Common Settings Name Fanuc Baudrate 2400 (or to match CNC setting) Data bits 7 Stop bits 2 Parity Even Flow control Xon/Xoff Xon Char. 17 Xoff char. 19 Port as available Send Settings Header String 37,13,10 23/05/2008 http://www.connectcnc-dnc.com/Settings/Fanuc%200T%20&%20M.html
-
Upload
luz-garcia -
Category
Documents
-
view
875 -
download
21
Transcript of DNC for Fanuc 0M y 0T
www.connectcnc-dnc.com
DNC / file transfer settings for Fanuc 0M and OT
Set the following parameters on the machine:
To set the CNC up for drip feed (0M): Enable parameter G127.5 Select AUTO (DNC) mode Send the program from the computer, then press Cycle Start on the Fanuc. To pause dripfeed, turn the Feedrate override to 0%.
Set ConnectCNC as follows:
Parameter Value
0002 00000001
0552 9
TV ON 0
ISO 1
I/O 0
Common Settings
Name Fanuc
Baudrate2400 (or to match CNC setting)
Data bits 7
Stop bits 2
Parity Even
Flow control
Xon/Xoff
Xon Char. 17
Xoff char. 19
Port as available
Send Settings
Header String 37,13,10
23/05/2008http://www.connectcnc-dnc.com/Settings/Fanuc%200T%20&%20M.html
Cable Pin Out
Trailer String 37,13,10
The above codes mean "%,CR,LF". If your program has the percent sign at the beginning and end, leave the Header and Trailer blank.
End of Line Sequence
Recognize customEOL
Replace
Check "%" character
checked if you have a "%" at the beginning and end of your programs.
Skip empty lines user's choice
Skip line numbers user's choice
Skip non printable bytes
user's choice
Skip comments check "(...)" if required
Default folderFolder in which you store this machine's programs
Start transfer delay
user's choice
Receive Settings
Header String
Trailer String
End of Line Sequence
Recognize custom EOL
Replace (checked)
13,10
Check "%" character
checked if you have a "%" at the beginning and end of your programs.
Skip empty lines user's choice
Skip line numbers
user's choice
Skip non printable bytes
user's choice
Skip comments check "(...)" if required
Default folderFolder in which you store this machine's programs
Start transfer delay
user's choice
Página 2 de 3ConnectCNC settings for Fanuc 0T and M
23/05/2008http://www.connectcnc-dnc.com/Settings/Fanuc%200T%20&%20M.html
Once you have ConnectCNC and your CNC machines communicating, we strongly suggest you take the following precautions: - Download some programs, the longer the better, from your CNC to the pc. Savethem under a temporary filename so you don't overwrite the original files. Examine themfor errors such as dropped or changed text. Do this for the first few programs that you use.
These settings have been collected from users of our software and machine tool distributers. We have listed them to help users of ConnectCNC to communicate between their computers and CNC controls. Since we have no control over the many variables involved, including such things as cable conditions, modifications to machines, condition of computer hardware, etc., we take no responsibility for any damage
caused to programs or machines through the use of this software.
Site Map ©Copyright CNC Consulting Inc. 1996-2008
Minimum system requirements for our software: Any computer with Windows95 v950B or higher(32 bit), 98, ME, 2000 XP, NT, Vista.
Hardware requirements will depend on the size of CNC files processed with EditCNC and ConnectCNC. However, ConnectCNC requires at least one serial COM port, or USB/RS232c port converter.
Página 3 de 3ConnectCNC settings for Fanuc 0T and M
23/05/2008http://www.connectcnc-dnc.com/Settings/Fanuc%200T%20&%20M.html
