OmniScan SX Getting Sta

Intended UseThe OmniScan SX is designematerials. Do not use the Om

Instruction ManualBefore use, thoroughly revieManual. Use the product as iuse this Olympus product saaccessible location. The PDFUsers Manual are also availaOmniScan SX, or can be dow

Safety Signal Word

Indicates an imminently hazwhich, if not correctly perfor

Indicates a potentially hazarif not correctly performed or

Indicates a potentially hazarif not correctly performed ordamage, particularly to the p

OmniScan SXGetting Started Guide

d to perform nondestructive inspections of industrial and commercial niScan SX for any purpose other than its intended use.

w the OmniScan SX Users Manual and the OmniScan MXU Software Users nstructed. The Users Manual contains essential information on how to fely and effectively. Keep this guide and the users manuals in a safe,

versions of the OmniScan SX Users Manual and OmniScan MXU Software ble on the documentation USB drive that is shipped with the nloaded at www.olympus-ims.com.

s

ardous situation calling attention to a procedure, practice, or the like, med or adhered to, could result in death or serious personal injury

dous situation calling attention to a procedure, practice, or the like, which, adhered to, could result in death or serious personal injury.

dous situation calling attention to a procedure, practice, or the like, which, adhered to, could result in minor or moderate personal injury, material roduct, destruction of part or all of the product, or loss of data.rted Guide 1

2Front PanelThe front panel of the OmniScan SX contains all the main controls and indicators. This panel is divided into six areas: the touch-screen display, the main control area, the function keys, the Power key, the Help key, and the indicator lights.

Main Control AreaYou can control the OmniSca

Element

Display touch screen

Alarm indicator lightsOmniScan SX Getting Started Guide

n SX using the main control area alone.

Name Description

Scroll knob Used to navigate through selections without the need for a keyboard, mouse, or touch screen. Turning the scroll knob in a clockwise direction shifts a selection to the left (horizontal list) or upward (vertical list).

Accept key Used to confirm a selection.

Cancel key Used to cancel the current selection, or to go back one level in the menu hierarchy.

Power indicator light

Acquisition indicator light

Help key

Power key

Function keys

Main control area

OmniScan SX Getting Sta

Turning On and Off the OmniScan SXTo turn on the OmniScan SX

Press the Power key for one second.The system starts up and performs a memory check. If the system encounters a problem during its start-up phase, the power indicator light will indicate the nature of the problem using a color code. Refer to the OmniScan SX Users Manual for more d

To turn off the OmniScan SX1. Quickly press the

The Select a comm

2. Select Shut DownA message asking

3. To save your setup

You can also turn off the OmHowever, your setup will NO

Sleep ModeThe OmniScan SX can be pu

To use the sleep mode1. With the OmniSca

The Select a comm

2. Select Sleep.3. To disable the slee

The OmniScan SXrted Guide 3

etails.

Power key.and message appears.

. you if you want to save your setup appears.

, select Yes.

niScan SX by pressing and holding the Power key for ten seconds. T be saved.

t into sleep mode when not in use to conserve power.

n SX turned on, quickly press the Power key.and? message appears.

p mode, quickly press the Power key. returns to its previous state (inspection or analysis mode).

4Connections

To reduce the risk of electric shock, avoid touching the inner conductor of the connectors. Up to 340 V can be present on the inner conductor of the UT connectors, and up to 115 V can be present on the PA connector. The warning symbol near the PA and UT connectors signals this electric shock risk.

Scan

UT conne

Battery compartment d

Warning symOmniScan SX Getting Started Guide

ner interface connector

ctors

PA connector

DC power adaptor plug (not shown)

Warning symbol

Memory card slot

oor SVGA output connector

USB portsbol

OmniScan SX Getting Sta

Warnings on Battery UseThe warning symbol on the battery compartment door signals that precautions must be taken concerning the battery.

Carefully read and observe the following warnings on battery use.

Do not open, crush Do not incinerate b

Exposing batteriesinjury.

Do not drop, hit, owhich are corrosiv

Do not short-circudamage to a batter

Do not expose a ba Only use the Omn

battery. Do not recharge a

the battery is pres Do not store batter

between 40 % and During storage, ke Do not leave the b

Replacing the BattTo replace the lithium-ion batter

1. On the left side pabattery compartm

2. Remove the batter3. Insert a new batter

inside the battery 4. Close the battery crted Guide 5

, or perforate batteries; doing so could cause injury.atteries. Keep batteries away from fire and other sources of extreme heat. to extreme heat (over 80 C) could result in an explosion or personal

r otherwise abuse a battery, as doing so could expose the cell contents, e and explosive.it the battery terminals. A short circuit could cause injury and severe y, making it unusable.ttery to moisture or rain; doing so could cause an electric shock.

iScan SX or an external charger approved by Olympus to charge the

battery unless the indicators light up when the capacity check button on sed. Doing so could be dangerous.ies that have less than 40 % remaining charge. Recharge batteries to

80 % capacity before storing them.ep the battery charged to between 40 % and 80 %.attery in the OmniScan SX during instrument storage.

eryynel, turn the two quarter-turn latches counterclockwise to open the ent door.y by pulling on the tab.y. Make sure that the groove on the battery is aligned with the small edge

compartment.ompartment door.

6Charging the Batte

The OmniScan SX DC poweOmniScan SX battery only (Ptype of battery, or use any otnot attempt to power or charas doing so could cause an e

To charge the battery Connect the Omni

Battery charging is performe

When the OmniSc When the Om

will automatThe power inrecharged. Worange light. discharged st

When the OmniSc When the Om

automaticallyBecause the Orecharge the completely d

For more information about

Battery compartment

doorOmniScan SX Getting Started Guide

ry

r adaptor (P/N: OMNI-A-AC [U8767093]) is designed to charge /N: OMNI-A-BATT2 [U8760059]). Do not attempt to charge any other

her chargers/adaptors. Doing so could cause an explosion or injury. Do ge other electronic equipment with the OMNI-A-AC DC power adaptor, xplosion resulting in death or serious personal injury.

Scan SX to a proper DC power adaptor.d as follows:

an SX is turned off:niScan SX is connected to a proper DC power source and is turned off, it

ically recharge the battery.dicator light flashes orange to indicate that the battery is currently being hen the charge is complete, the power indicator light emits a steady The battery can take up to 3 hours to fully charge from a completely ate (less than 5 % remaining charge).an SX is running:niScan SX is running and connected to a proper DC power source, it will recharge the battery. The indicator for the battery is green.mniScan SX is running, less power is available from the DC source to

battery. As such, it could take a minimum of 8 hours to charge a ischarged battery.

battery charge status, refer to the OmniScan SX Users Manual.

Lithium-ion battery (P/N: OMNI-A-BATT2 [U8760059])

OmniScan SX Getting Sta

Battery Status IndicatorsWhen the OmniScan SX is running, the battery status is shown by an indicator located on the upper-left corner of the touch-screen display. This indicator displays the amount of power remaining in the battery using one of the two following methods:

The remaining operational time is displayed inside the battery status indicator. This information can only be displayed accurately after the OmniScan SX has been operating for approximately 15 minutes.

The charge indicatthe amount of pow

If you attempt to start up thepower indicator light rapidlyOmniScan SX, replace the ba

The OmniScan SX software ksome of the battery status in

For other status indications,

Indicator

D

B

Y(b

R(b

Nrted Guide 7

or (bar) inside the battery status indicator provides an approximation of er remaining for that battery. OmniScan SX using a battery with a charge too low for operation, the flashes red for approximately three seconds. To operate the ttery or plug in the DC power adaptor.

eeps the user informed of the battery status. The table below describes dicators available:

refer to the OmniScan SX Users Manual.

Outline Fill Meaning

otted N/A There is no battery in that compartment.

lue Blue The battery is functioning properly.

ellow linking)

Blue The battery is charging.

edlinking)

Blue The battery charge is critically low (less than 10 %). A beeping noise is emitted.

/A Yellow The OmniScan SX is being powered externally through the DC adaptor.

Olympus NDT, 48 Woerd Awww.olympus-ims.comPrinted in Canada 2013 by OlympAll brands are trademarks or registere

Part ID: U8778632

DMTA-20044-01ENRev. A, February 2013venue, Waltham, MA 02453, USA

us. All rights reserved.d trademarks of their respective owners and third party entities.

*U8778632*Printed on Rolland Hitech50,

which contains 50 % post-consumer fiber.

*DMTA-20044-01EN*

50%

OmniScan SX Getting Started Guide

Intended UseInstruction ManualSafety Signal WordsFront PanelMain Control AreaTurning On and Off the OmniScan SXSleep ModeConnectionsWarnings on Battery UseReplacing the BatteryCharging the BatteryBattery Status Indicators

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False

/CreateJDFFile false /Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure false /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles false /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /DocumentCMYK /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /UseDocumentProfile /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice