DLM142E
Transcript of DLM142E
-
TESTO ITC KORINNA 28mm Allargato
LOAD SENSING MONOBLOCKDIRECTIONAL CONTROL VALVE
-
DLM142
2 DAT010E
Features
Simple, compact and heavy duty designed 2 sections monoblock valve, for hydraulic systems with load sensing variable displace-ment pump.H Each spool has indipendent load check valve.H Parallel circuit.H A wide variety of service port valves.H Available with manual, electro--hydraulic and remote with flexible cables spool control kits.H Diameter 18 mm -- 0.71 in interchangeable spools.
WARNING!All specifications of this catalogue refers to the standard product at thisdate. Walvoil, oriented to a continuous improvement, reserves the right to
discontinue, modify or revise the specifications, without notice.
WALVOIL IS NOT RESPONSIBLE FOR ANY DAMAGE CAUSED BY AN
INCORRECT USE OF THE PRODUCT.3rd edition January 2000:This edition supercedes all prior documents.
Additional informationThis catalogue shows the product in the most usual configurations.Please contact Customer Service Dpt. for more detailled information orspecial request.
-
DLM142
3DAT010E
Contents
ContentsSpecifications 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Dimensional data 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Hydraulic circuit 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Performance data 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ordering codes 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Spool 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A side spool positioners 11. . . . . . . . . . . . . . . . . . . . . . . . . . .B side options 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Port relief options 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Special configurations 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Installation and maintenance 25. . . . . . . . . . . . . . . . . . . . . . . .
-
DLM142
4 DAT010E
This catalogue shows technical specifications and diagrams measured with mineral oil of 46 mm2/s -- 46 cSt viscosity at 40C tempera-ture.
Nominal flow rating 80 l/min
Operating pressure (maximum) 250 bar 3600 psi
Max. back pressure on outlet port T 10 bar 145 psi
Internal leakage A(B)T Dp=100 bar -- 1450 psifluid and valve at 40C
3 cm3/min 0.18 in3/min
Fluid Mineral oil
Fluid temperature with NBR (BUNA--N) seals from --20 to 80C
with FPM (VITON) seals from --20 to 100C
Viscosity operating range from 15 to 75 mm2/s from 15 to 75 cSt
min. 12 mm2/s 12 cSt
max 400 mm2/s 400 cSt
Max level of contamination 19/16 -- ISO 4406
Ambient temperature from --40 to 60C
NOTE -- For different conditions please contact Customer Service.
Working conditions
-
DLM142
5DAT010E
Standard threads
PORTS BSP(ISO228/1)
SAE UN--UNF METRIC(ISO 262)
Inlet P and outlet T G 3/4 SAE 12 (1 1/16--12 UN) M27x2A and B ports G 1/2 SAE 10 (7/8--14 UNF) M22x1,5Load sensing LS port G 1/4 SAE 6 (9/16--18 UNF) M14x1.5
Dimensional data
WALVOIL
DLM142/2
103230011
P9900001
MADE IN ITALY
Valve code
Production batch :P99 = production year (1999)00001 = progressive number
Valve type
WALVOILDLM142/2103230011P9900001
MADE IN ITALY
56.5
2.22
19.50.77
391.54
P Tb2a2a1b1
B2A2A1B1
461.81
200.79
451.77
155
6.10
1776.97
265.
510
.45
19 0.75
82.5
3.25
18 0.71
92.5
3.64
M5 13.5
0.53
18 0.71
250.98
26.5
1.04 34
.51.
36
16.5
0.65
200.79
451.77
42.51.67
351.38
28.51.12
11.50.4554.52.15
411.61
70.5
2.78 68 2.68
86 3.39
75.52.97
130.
51 16 0.63
M8
1084.25
Position 0
Position 1
Position 2
Position 3
-
Hydraulic circuit
To prevent spools sticking due to temperature shock, the valve is available in a special configuration with the connection of the pres-sure line with tank through a small orifice ( 0.6 mm / 0.024 in).There is a small amount of flow constantly going to tank, but this system keeps the valve body warm with spools in neutral position.This configuration is particularly suitable for application in cold environment.
Tank line
P
A1 B1
T
A2 B2
Ex.: DLM142/2--AP/113SL/18MASL--
P T
Allen wrench 624 Nm / 17.7 lbft
Load check valveAllen wrench 8 -- 24 Nm / 17.7 lbft
Pressure line
A ports lines
Allen wrench 49.8 Nm / 7.2 lbft
LS
Shuttle valve
0.6
0.02
4
Load sensingsignal (LS)
B ports lines
Optional plug with metering hole
A2 B2
LS T
0.6 mm0.024 in
Ex.: DLM142/2--AP/113SL/18MASL--FC0.6--
Requires special valve body kit:contact Customer Service
DLM142
6 DAT010E
-
Work port to outlet
Inlet to work port
Performance data (pressure drop vs. flow)
A1 A2B1 B2
P TLS
A1 A2B1 B2
P TLS
0
10
20
30
40
0 30 60 90 120
0
10
20
30
40
0 30 60 90 120Flow
Pre
ssur
edr
op
540
360
180
(l/min)
(bar)(psi)
FlowP
ress
ure
drop
540
360
180
(l/min)
(bar)(psi)
From inlet to A (spool in position 1) or B (spool in position 2).
From A port (spool in position 2) or B port (spool in position 1) to outlet.
A2(B2)T
A1(B1)T
PA2(B2)
PA1(B1)
DLM142
7DAT010E
-
DLM142
8 DAT010E
5. Port relief options page 13
4. B side options page 12
3. A side spool positioner page 11
2. Spool page 10
1. Body kit *
Ordering codes
1.
DLM142/ 2 -- AP / 1 13 SL / 18MASL . P1(G3 -- 100) -- *
TYPE CODE DESCRIPTION2--AP 5KC1903005 2 sections
TYPE CODE CIRCUIT DESCRIPTION1 3CU1310210 Double acting, 3 postions, A and B closed
in neutral position with positioner kit 8MA.4 positions, A and B to tank in 4th positions(float) with positioner kit 13
3.
13
8MA
TYPE CODE DESCRIPTION8MA 5V08108240 With spring return in neutral position13 5V13108040 With detent in position 3 and spring return
in neutral position
2. 3. 4. 5.
Include body, seals, rings and load check valves.
NOTE -- (*) Items are referred to BSP thread.
1st section 2nd section
1.
TYPE CODE DESCRIPTIONSL -- Prearranged for mechanical remote
controlTQ 5TEL108210 Prearranged for cable remote control
TYPE CODE DESCRIPTIONAnti--shock valveP(G3--100) 3XCAR208113 Range 100 to 250 bar / 1450 to 3600 psi
standard setting 100 bar / 1450 psiP(G4--200) 3XCAR208114 Range 200 to 315 bar / 2900 to 4600 psi
standard setting 200 bar / 2900 psiAnti--shock and anti--cavitation valveU(G2--63) XCAR308112 Range63 to 125 bar / 900 to 1800 psi
standard setting 63 bar / 900 psiU(G3--100) XCAR308115 Range 100 to 250 bar / 1450 to 3600 psi
standard setting 100 bar / 1450 psiU(G4--200) XCAR308114 Range 200 to 315 bar / 2900 to 4600 psi
standard setting 200 bar / 2900 psiStandard setting is referred to 10 l/min flow.
C XCAR408110 Anti--cavitationP3T 3XTAP524290 A and B ports valve blanking plugs
2.
5. P U C P3T
4.
SL
TQ
Black painted
Example:
Port relief valve setting in bar
-
DLM142
9DAT010E
DLM142 valve with proportional electro--hydraulic control and quick--action coupling
DLM142 valve with quick--action coupling
DLM142 valve with proportional electro--hydraulic control
Special configuration - page 17 Ordering codes
DLM142/2--APE/113EZ3/KE2/18EZ3--FC0.6--12VDC--MACH4--*
DLM142/2--APE/1 13EZ3 / KE2 /1 8EZ3 -- FC0.6--12VDC -- *
Code of this configuration: 103230021
Code of this configuration: 103230013
Code of this configuration: 103230022
Lock cam not included (for code see page 24)
Lock cam not included (for code see page 24)
Example:
Example:
Example:
DLM142/2--AP/113SL/18MASL-- MACH4 -- *
-
FJ
YP(on ports) = 63bar/900psiP(on ports) = 100bar/1450psiP(on ports) = 250bar/3600psi
0
30
60
90
0 1 2 3 4 5 6 7
Flow
Stroke
Spool metering A(B)T0.1 0.2
(mm)
(l/min )
(in)
Qin = 80 l/min
FJ
Y
NOTE -- A Only for positioner kit type 13
Type 1
Spool
0
30
60
90
0 1 2 3 4 5 6 7
Flow
Stroke
Spool metering PA(B)0.1 0.2
(mm)
(l/min )
(in)
Performance data
"
P A--LS B T
P B--LS A T
AB
T PLS
A--B--LS T (floating circuit)
P--A--B--T closed, with LS load sensing line to tank
201A B
P T
3
stroke =+ 7 mm+ 0.28 in
T P
TP
AB
T PLS
T P
TP
AB
T PLS
T P
TP
AB
T PLS
T P
TP
LS
P
201A B
P T
3LS
P
201A B
P T
3LS
P
201A B
P T
3LS
P
A
AA
stroke =-- 7mm-- 0.28 in
stroke =-- 12 mm-- 0.47 in
A stroke = -- 6.7 mm-- 0.26 in
z P(on ports) = 20bar/290psi
z
DLM142
10 DAT010E
-
--400
--200
0
200
400
--12 --10 --8 --6 --4 --2 0 2 4 6(mm)
Forc
e
Force--stroke diagram
Stroke
(N) (lbf)
(in)
7
80
40
--80
--40
0
--0.2 --0.1--0.3--0.4 0 --0.2--0.1
From position 2 to 3
From position 0 to 2
From position 0 to 1
Locking--unlocking areaLocking force:300 N / 67.4 lbf 10%Unlocking force:270 N / 60.7 lbf 10%
(mm)
--150
--75
0
75
150
--7 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6 7
Forc
eC
BA
Force--stroke diagram
Stroke
(N)0.1 0.2 (in)
20
10
(lbf)--0.1--0.2 0
CB
A
30
0
--20
--10
--30
With detent on 4th position float circuit
With spring return
A side spool positioner
201 3
13 kit
50
Allen wrench 46.6 Nm / 4.9 lbft
Allen wrench 624 Nm / 17.7 lbft
Supplied with standard spring type A (see force--stroke diagram).Available with heavier spring type B (8 code: 5V08108010) or type C (8MC code: 5V08208000).
8MA kit
201
1.97
82.53.25
Allen wrench 46.6 Nm / 4.9 lbft
Wrench 624 Nm / 17.7 lbft
DLM142
11DAT010E
-
TQ cable remote control
SL prearranged for mechanical remote control
B side options
Waterproof cap prearranged for remote control with flexible cable.
NOTE -- For more information concerning remote cable control require appropriate documentation.
201
201
Allen wrench 46.6 Nm / 4.9 lbft
Wrench 10
CD flexible cable to be orderedseparately
Wrench 24
80.53.17
281.10
3CU1310210
165
0.20
190.75
0.6
318
0.7
1
8H80.31490.3158
Spool dimension
190.75
DLM142
12 DAT010E
-
Anti--shock valve
Port relief options
0.18RESPONSE TIME
10%
100
bar
1450
psi
90%95%
105%
Pre
ssur
e
Time ()
(% DP)
Response time
0
100
200
300
400
0 30 60 90Flow
Pre
ssur
e
4500
3000
1500
(l/min)
(psi)(bar)
Spring nr. 4 (red band)
0
100
200
300
400
0 30 60 90Flow
Pre
ssur
e
4500
3000
1500
(l/min)
(psi)(bar)
Spring nr. 3 (blue band)
P 1 ( G 3 -- 100 )
Adjustment type (G, H).
Pressure setting in bar.
Spring type (3, 4). AP1
max20.5
Wrench 2442 Nm / 31 lbft
Notch1.5 mm / 0.06 in
Wrench 2242 Nm / 31 lbft
Performance data
Adjustment type
G: with screw H: valve set and locked
1 mounted on A port.2 mounted on B port.3 mounted on A and B ports.
0.81
B
T
AP2
B
T
AP3
B
T
DLM142
13DAT010E
-
Anti--shock and anti--cavitation valve
Port relief options
0.45RESPONSE
TIME
10%
100
bar
1450
psi90%
95%
105%
Pre
ssur
e
Time ()
(% DP)
Response time
0.6TRANSIENT
RECOVERY TIME
18 bar260 psi
OVERSHOOT
0
100
200
300
400
0 30 60 900
100
200
300
400
0 30 60 900
100
200
300
400
0 30 60 90
Spring nr. 2 (green band)
Flow
Pre
ssur
e
4500
3000
1500
(l/min)
(psi)(bar)
Flow
Pre
ssur
e
4500
3000
1500
(l/min)
(psi)(bar)
Flow
Pre
ssur
e
4500
3000
1500
(l/min)
(psi)(bar)
Spring nr. 3 (blue band) Spring nr. 4 (red band)
U 1 ( G 3 -- 100 )
Performance data
Adjustment type
G: with screw H: valve set and locked
AU1
B
T
AU2
B
T
AU3
B
T
Adjustment type (G, H).
Pressure setting in bar.
Spring type (2, 3, 4).
1 mounted on A port.2 mounted on B port.3 mounted on A and B ports.
max20.5
Wrench 2442 Nm / 31 lbft
Notch1.5 mm / 0.06 in
Wrench 2242 Nm / 31 lbft
0.81
Pressure drop
0
20
40
60
0 10 20 30 40Flow
Pre
ssur
e
750
500
250
(l/min)
(psi)(bar)
DLM142
14 DAT010E
-
P3T: port relief valve blanking plug
Anti--cavitation valve
Port relief options
0
6
12
18
24
0 30 60 90
Pressure drop
Flow
Pre
ssur
e
300
200
100
(l/min)
(psi)(bar)
Performance data
C 11 mounted on A port.2 mounted on B port.3 mounted on A and B ports. A
C1B
T
AC2
B
T
AC3
B
T
Wrench 2442 Nm / 31 lbft
11.50.45
Allen wrench 1042 Nm / 31 lbft
A B
T
DLM142
15DAT010E
-
DLM142
16 DAT010E
-
Special configurations
Proportional electro- hydraulic control
Quick- action coupling
Proportional electro- hydraulic controland quick- action coupling
page 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DLM142
17DAT010E
-
DLM142
18 DAT010E
Dimensional data
Special configurations Proportional electro- hydraulic control
T
B2A2A1B1
b2a2b1 a1
346
13.6
214
95.
8714
45.
67
461.81
10.04
1787.01
19.50.77
92.5
3.64
18 0.71
38.5
1.52
180.
71
391.54
56.5
2.22
10.5
0.41
134.55.29
26.51.04
Spool positioner kit type 8EZ3 (3 positions).Code: 5V08642000
Spool positioner kit type 13EZ3 (4 positions).Code: 5V13918000
Electro--hydraulic module type KE2--12VDCCode: 5IDR818120
Special valve body kit required.Code: 5KC1903003
NOTE -- For threads refer to page 5
-
Hydraulic circuit
Proportional electro- hydraulic control Special configurations
Standard execution is with closed center circuit for variable displacement pump.
P
A1 B1
T
A2 B2
Ex.: DLM142/2--APE/113EZ3/KE2/18EZ3--FC0.6--12VDC--
LSMX
1B 1A 2B 2A
LEGEND1A--1B 1st section proportional solenoid pressure reducing valves2A--2B 2nd section proportional solenoid pressure reducing valvesCV check valve on pilot lineCVA load check valve on 1st sectionCVB load check valve on 2nd sectionF filterR restrictor 0.6 mm / 0.024 inSV shuttle valve
CVF
SV
RC
VA
CV
B
DLM142
19DAT010E
-
Positioner kit type 13EZ3Positioner kit type 8EZ3
KE2--12VDC module
Special configurations Proportional electro- hydraulic control
Tb2a2b1 a1
1345.28
82 3.23
62 2.44
652.56
451.77
471.85
2A1A
2B1B
220.87
1345.28
15 0.59
50 1.97
44 1.73
21.5
0.85
Solenoid operating featuresNominal voltage : 12 VDC. . . . . . . . . . . . . . . . .Power rating : 11.9 W. . . . . . . . . . . . . . . . . . . .Resistance : 5.3 W. . . . . . . . . . . . . . . . . . . . .Duty cycle : 100%. . . . . . . . . . . . . . . . . . . . . .
Allen wrench 624 Nm / 17.7 lbft
Allen wrench 36.6 Nm / 4.9 lbft
Filter kit for pressure reducing valve pilot lineAllen wrench 6 -- 24 Nm / 17.7 lbft
Solenoid
Pressurereducing valve
481.89
Allen wrench 46.6 Nm / 4.9 lbft
Allen wrench 624 Nm / 17.7 lbft
532.09
Allen wrench 46.6 Nm / 4.9 lbft
Allen wrench 624 Nm / 17.7 lbft
Allen wrench 515 Nm / 11 lbft
59 2.32
Pressure gauge connection (plugged)G 1/4 threadAllen wrench 6 -- 24 Nm / 17.7 lbft
Accumulator connectionG 1/4 thread
Steel wire filter6x5 mm (0.236x0.197 in) -- 60 m
ConnectionAMP junior timermale type
DLM142
20 DAT010E
-
030
60
90
0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2
Spool metering curve
Solenoid current
(l/min)
Por
tsflo
w
(A)
4th positionfloat
--1.25
--1.00
--0.75
--0.50
--0.25
0.00
0.25
0.50
0.75
1.00
3 4 5 6 7 8 9
0.45 A
0.8 A
0.45 A
0.8 A
1.2 A
Current output curve vs. joystick signal
Inlet voltage
(A)
Out
putc
urre
nt
(V)
0.65 A
0.9 A
0.9 A
0.65 A
4th position float1st spool2nd spool
Example of electrical connections
Proportional electro- hydraulic control Special configurations
T
B2A2A1B1
b2a2b1 a1
+ --12 VDC
2A1A
2B
BATTERY
1 2 3 4 5 6 7 8 9
1 2
213
leds
1B
DLM142
JOYSTICK
1B
1A
2B2A
Float
CONTROL UNIT
DIRECTIONAL VALVE
series MEW010
series UGA22
NOTE -- For further information about electrical system requirements, refer to ARC300 catalogue DEV001IE
Connection AMP junior timerfemale type
2nd Spool1st Spool
DLM142
21DAT010E
-
For DLM142 valve with manual control
Special configurations Quick- action coupling
This prearrangement requires special valve body kit code: 5KC1903006 , wich include body, seals, rings, load check valves, fixingflange and quick--action coupling joints.This configuration needs special positioner kit type 13 code: 5V13108050.
B1 A1 A2 B2
b1 a1 a2 b2 TP
14.5
0.57
49 1.92
32 1.26
265.
510
.45
66.5
2.62
59.52.34
2037.99
762.99
1184.65
Fixing flange
Quick--action coupling jointtype A12.5 UNI--ISO 7241/1
M10
body kit
special kit type13
DLM142
22 DAT010E
-
For DLM142 valve with proportional electro--hydraulic control
Quick- action coupling Special configurations
This prearrangement requires special valve body kit code: 5KC1903007 , wich include body, seals, load check valves, fixing flangeand quick--action coupling joints.
762.99
1184.65
Fixing flange
14.5
0.57
49 1.92
32 1.26
359.
514
.15
66.5
2.62
59.52.34
2037.99
Quick--action coupling jointtype A12.5 UNI--ISO 7241/1
M10
body kit
prop. electro--hydraulic control (see page 18)
T
B2A2A1B1
b2a2b1 a1
DLM142
23DAT010E
-
Lock cam kit
Special configurations Quick- action coupling
Code: 5X7200
b2a2
a1b1
B2
A2
A1
B1
DLM142 valve withprearrangement
(see pages 22, 23)
Lock camcode: 2X7201
B1
A1
A2
B2
160.63
33413.15
250
9.84
1254.92
M22
x1.5
2.50.1
122.54.82
PG 9electric gland
Joint ISO 8434--1
Dimensional data
Protective boxcode: 2X7202
Lock pincode: 2X7203
NOTE -- Availability for different type of quick--action coupling on request, contact Customer Service.
DLM142
24 DAT010E
-
DLM142
25DAT010E
Fittings tightening torques -- Nm / lbft
THREAD TYPE P and T ports A and B ports LS, X, M ports
BSP (ISO 228/1) G 3/4 G 1/2 G 1/4With O--Ring seal 70 / 51.6 50 / 36.9 25 / 18.4With copper washer 70 / 51.6 60 / 44.3 30 / 22.1With steel and rubber washer 70 / 51.6 60 / 44.3 16 / 11.8
SAE SAE 12 (1 1/16--12 UN) SAE 10 (7/8--14 UNF) SAE 6 (9/16--18 UNF)With O--Ring seal 95 / 70.1 60 / 44.2 30 / 22.1
METRIC (ISO 262) M27 x 2 M22 x 1.5 M14 x 1.5With O--Ring seal 90 / 66.4 50 / 36.9 25 / 18.4With copper washer 60 / 44.3 40 / 29.5 30 / 22.1With steel and rubber washer 70 / 51.6 60 / 44.3 20 / 14.8
LS
T
P
MX
A1A2
B2
B1
P
T
A1A2
B2
B1
LS
Installation and maintenance
The DLM142 valve is assembled and tested as per the technical specification of this catalogue.Before the final installation on your equipment, follow the below recommendations:-- the valve can be assembled in any position; in order to prevent body deformation and spool sticking mount the product on a flat
surface;-- in order to prevent the possibility of water entering the spool control kit, do not use high pressure wash down directly on the valve;-- prior to painting, ensure plastic port plugs are tightly in place.
Standard configuration Electro--hydraulic configuration
NOTE -- These torque are recommended. Assembly tightening torque depends on many factors, including lubrication, coating andsurface finish. The manufacturer shall be consulted.
-
Installation and maintenance
Spool
Body
Normally spools are interchange-able. Verify the smoothness duringthe assembly
Load check valve
Sealingedge
Port valve blankingplug
Only for electro--hydraulic configuration
Positioner kit
O--Ring seals 18x2.5code: 4GUA118025
Chamfer
Holding O--Ring bushingcode: 3ANE134041
NOTE (only for valve with machanical control) -- All articulated parts inside cap are lubricated with synthetic base grease gradeNLGI2.
DLM142
26 DAT010E
MALFUNCTION CAUSE REMEDY
External leakage control kit or oppositeside.
Worn spool seal due to mechanicalactuation or high back pressure.
Locate the leakage and replace the seal.Check back pressure level.
Excessive internal leakage on A and Bports.
Increase clearance between spools andbody due to high wear
Replace the directional control valve andcheck the oil contamination level.
Dropping load during transition whileraising High leakage on the load check valve.
Remove the load check valve and cleanthe seat.
Inability to build pressure on A and BPort relief valve open. Remove and clean or replace the portrelief valve.Inability to build pressure on A and B
ports. Low pump pressure and flow. Check the pump and circuit.ports.Low voltage supply. Check electric system.
Electro--hydraulic control unproportionalmovement.
Proportional pressure reducing valveblocked. Remove the valve and clean it.
movement.High spool friction. Remove the spool an clean it carefully.
-
Master Distributors and Resellers
MALAYSIA POWER FLUIDTRONICS AND SDN BHD.No 12 and 14Seksyen 31, Kota Kemuning40460 Shah Alam Selangortel. 0060 3 5220188fax. 0060 3 5220133
AUSTRALIA SOUTHCOTT PTY.LTDHalifax street G.P.O.B. 10635000 Adelaide S.A.tel. 0061 8 2282411fax. 0061 8 2233413
AUSTRIA RACHER MASCHINEN HYDRAULIKRedlham 1004800 Attnang Puchheimtel. 0043 7674606fax. 0043 7674 606 22
BELGIUM HAGOMATGuldensporenstraat 701800 Vilvoordetel. 0032 2 2521373fax. 0032 2 2512263
DENMARK DANFOSS HYDRAULIK A/SToppevadvej 44--46 GanloesePostboks 429 Stenloese 3660tel. 0045 42 184055fax. 0045 42 184603
FINLAND BERENDSEN PMC OY ABPL 3233901 Tamperetel. 00358 3 31410300fax. 00358 3 2123748
FRANCE FLUIDES TECH. APPLICATIONS6 avenue H. Beaudelet Z.A. de la Gare77330 Ozoir la Ferrieretel. 0033 1 64400029fax. 0033 1 64403288
GERMANY BALSTER HYDRAULIK G.m.b.H.Postfach 11014144057 Dortmundtel. 0049 231 590021fax. 0049 231 592645
NOLD HYDRAULIK+PNEUMATIK G.m.b.H.Enzisreute88339 Bad Waldseetel. 0049 7524 97200fax. 0049 7524 972070
RAUH HYDRAULIK G.m.b.H.Hallstadter strasse 6396052 Bambergtel. 0049 951 966360fax. 0049 951 9663699
TH. NIEHUES G.m.b.H.Bahnhofstrasse 8148308 Senden, Bosenselltel. 0049 2536 99001fax. 0049 2536 99019
GREECE C. PARIS & CO. O.E.53 Marathonomachon str.akad10441 Platonos, Athenstel. 0030 1 5135701fax. 0030 1 5144579
CANADA CANIMEX INC.285 St. Georges J2C 4H3Drummondville Quebectel. 001 819 477 1335fax. 001 819 477 2908
HOLLAND ABS HYDRAULICS B.V.Lloydsweg 8P.O.B. 69641 KK Veendamtel. 0031 598 6 22544fax. 0031 598 6 20875
KAVEE HYDRAULICSAaltenseweg 62Postbus 1497050 AC Varsseveldtel. 0031 315 254111fax. 0031 315 244401
TECHNISCH CENTRUM GROOT B.V.Winkelerzand 3P.O.B. 11731 LZ Winkeltel. 0031 224 544444fax. 0031 224 544433
ICELAND LANDVELAR EHFSmiojuvegur 66P.O. box 20200 Kopavogurtel. 00354 557 6600fax. 00354 557 8500
ITALY CONSUL FLUID S.A.Sdi Plicchi Fabio & C.via Luciano Romagnoli 2740069 Zola Predosa, Bolognatel. 0039 051 6167474fax. 0039 051 6167411
FER HYDRAULIK S.R.Lvia Lambrakis 16--16/A42100 Reggio Emiliatel. 0039 0522 332177fax. 0039 0522 553891
OLEODINAMICA GAMBINI S.R.L.Strade Cattane 836100 Vicenzatel. 0039 0444 962030fax. 0039 0444 961993
OLEODINAMICA GIANNINI S.R.L.via Arno 1350019 Osmannoro, Firenzetel. 0039 055 374691fax. 0039 055 300290
OLEOMEC S.R.L.via Divisione Acqui61027 Villa Fastiggi, Pesarotel. 0039 0721 281861fax. 0039 0721 281825
OLEO MECCANICA INDUSTRIALECOMPONENTI S.R.L.via Nenni 220060 Bussero, Milanotel. 0039 02 95330080fax. 0039 02 95330090
PARMAFLUID S.R.L.via Azzoni 9/A43100 Parmatel. 0039 0521 480711fax. 0039 0521 480750
RVS DI CAVIASSO A. & C. S.A.S.via Macedonia 2410097 Collegno, Torinotel. 0039 011 4031333fax. 0039 011 4031479
ISRAEL L.Y.A. CO. LTD105 Hahashmonaim st.67011 Tel Avivtel. 00972 3 5611712fax. 00972 3 5613250
KOREA TOKIMEC KOREA HYDRAULICS CO. LTDLG Bldg 5F152 055 Guro--Dong, Guro--Gu, Seoultel. 0082 2 630 5850fax. 0082 2 630 5859
NORWAY LAUTOM ASHauger Skolevei 181351 Rudtel. 0047 67 178300fax. 0047 67 178305
PORTUGAL GUSTAVO CUDELL LDAR.Eng.Ferreira Dias 9544100 Oportotel. 00351 2 6102004fax. 00351 2 6158010
MOVICONTROL LDARua Prof.Henrique de Barros 5AP2685 Prior velhotel. 00351 1 9429900fax. 00351 1 9413500
SINGAPORE FLO--LINE HYDRAULICS PTE LTD47 Joo koon circleSingapore 629067tel. 0065 8632 022fax. 0065 8631 825
SOUTH AFRICAHYFLOSouthern Africa ltdP.O. box 240 Paarden eiland 7420tel. 0027 21 511 7021fax. 0027 21 5114456
LOWE ERNEST6 Skew road1460 Boksburg Northtel. 0027 11 8944281fax. 0027 11 8946108
SWEDEN HYDRAC ABGetaengsvaegen 2250263 Borastel. 0046 33 127470fax. 0046 33 125879
SPAIN INTERSEAL S.A.Autovia de Castelldefels Km 508820 El prat de Llobregat Barcelonatel. 0034 93 3706711fax. 0034 93 3701807
SWITZERLANDBT HYDRAULIK AGFischermattelistrasse 63000 Berna 5tel. 0041 31 3798141fax. 0041 31 3823980
TAIWAN LIMIT TEIN INDUSTRIAL CO. LTD2F. NO. 8--1 lane 42 sec.3TZU Ching rd. Sanchung cityTaipei Hsientel. 00886 2 9995022fax. 00886 2 9995055
THAILAND SRITONG ENGINEERING CO. LTD8/233--236 Moo 4 Rama 210150 Bangmod chomthong, Bangkoktel. 00662 428 4171fax. 00662 428 4180
TURKEY HIDRO KONTROL MAK. SANAYI VE TIBuyuk Sanayi 1 Cadde Arpacio 2Ishani n. 95/11 Iskitler6060 Ankaratel. 0090 312 3842895fax. 0090 312 3414476
HIDROTAS DIS TICARET A.S.Halit Ziya bulv n.33Zuhal is han--Izmirtel. 0090 232 4842253fax. 0090 232 4837463
UNITED KINGDOMBYPY HYDRAULICS &TRANSMISSIONS LTDNO. 8 Lingen road sheet R.I.E.Ludlow salop sy8 1xdtel. 0044 1 584 873012/3/4fax. 0044 1 584 876647
USA MC ELROY FLUID POWER826 North Fulton74158 Tulsa Oklahomatel. 001 918 8369055fax. 001 918 8319300
CHINA DRENNAN COMPANY LTD.2111 Wing on House71 Des Voeux Road CentralHong Kongtel. 00852 2817 3523fax. 00852 2817 3735
INDIA METTERS PRIVATE LT.144 St. Johns Church Rd.Bangalore 560 005tel. 0091 080 554 2949fax. 0091 080 555 5064
IRELAND NELSON HYDRAULICS LTDUnit 54, Cookstow Ind. EstateTallaght Dublin 24 jtel. 00353 1 4510 622fax. 00353 1 4510 893
MOROCCO MECOMAR S.A.7 Rue Abdelwahed el MarrakchiOukacha, Casablancatel. 00212 2 661550--1--2fax. 00212 2 661555
NEW ZELAND VICKERS SYSTEMS LTD77--79 Ben Lomond CrescentP.O.Box 51 076 PakurangaAouklandtel. 0064 9 576 9089fax. 0064 9 576 5865
POLAND IOW POLSKAU.L. Brukselska 103973 Warszawatel. 0048 22 6161313fax. 0048 22 6178485
TUNISIA AFRICA INDUSTRIEN.Z.I Ben ArousTunistel. 0021 61 1 384510fax. 0021 61 1 384476
-
WALVOIL S.P.A.
42100 REGGIO EMILIA ITALY VIA ADIGE, 13/DTEL. +39.0522.932411 FAX +39.0522.300984
E--MAIL: [email protected] HTTP: //WWW.WALVOIL.COM
CUSTOMER SERVICE
TEL. +39.0522.932555 FAX +39.0522.932455
D1409808IDAT010E