DIY Analyzer - sp.maytronics.comsp.maytronics.com/Marcom/0/17055/17055_1.pdf · 1. Do not...
Transcript of DIY Analyzer - sp.maytronics.comsp.maytronics.com/Marcom/0/17055/17055_1.pdf · 1. Do not...
DIY Analyzer
DIY Analyzer
Introduction As part of our commitment to the robotic pool cleaner market, Maytronics has developed a new Analyzer for diagnosing problems in DIY motor units. The Analyzer identifies defective motors and PCB cards and transfers this data to a computer. It can read all types of Dolphin DIY motor units, even those installed in old models. By using the Analyzer, repair costs can be dramatically reduced. Front panel
Back panel
Power supply on/off LED
Test button
Drive motor
1 test
Drive motor 2 test
Impeller motor test
PCB card test
Flash drive
entry
Motor unit cable entry
Battery test
on/off button
Cable connection between motor
unit and Analyzer
Cable connection between Analyzer and motor unit PCB card
Self-test connections for resetting Analyzer
Cable connection between computer
and Analyzer
Mains power cord – between Analyzer and
power supply
DIY Analyzer
Operating Instructions
1. Set up
Place the Analyzer on a clean and dry surface. Connect the Analyzer to your PC by plugging in the communication cable between the Analyzer and your computer’s USB port as shown below:
Plug in the mains power cord to a power supply. We recommend the new Diagnostic 29V digital switch mode power supply: Note: For the Analyzer to work, it must be connected to a power supply.
Connection to PC
Connection to Analyzer
Plug the cable into the PC USB port
Plug the cable into the back of the Analyzer
Connect the power cord to the power supply
Digital switch mode power supply
Connect the power cord to the power supply
Digital switch mode power supply
DIY Analyzer
Install the Analyzer PC communication software on your computer. The software is on the disk-on- key provided with the Analyzer. To install the program, save a copy of the software on your computer’s desktop. Double click on the set-up icon:
A new icon will appear. Double click on it: Double click “Next” on the set-up screens and then double click “Close”.
Press the
'Close' button.
DIY Analyzer
When the software installation has been completed, a file named “Maytronics” will appear on your Desktop:
Double Click on the “Maytronics” file to open the Analyzer program. The following screen will appear:
When you press on the Analyzer’s “Test” button, the motor unit data will appear on this screen.
Note: The Analyzer program must be open on your computer before running a test with the Analyzer.
DIY Analyzer
2. Testing Procedures The Dolbox/scanner test
To scan the motor unit and display the data on your computer, open the Analyzer program and do as follows:
A. When all LEDs are green – the motor unit is ok and the Analyzer has finished collecting the motor unit data and has sent it to the Analyzer program on your computer.
Wait until all LEDs are green.
The data in the Analyzer program
Print file
Save file
Connect the Dolphin cable Amphenol to the
Analyzer motor unit socket and press “Test.”
The red and green LEDs flash to signal the Analyzer is collecting data from the MU and
sending it to your computer.
DIY Analyzer
B. When all LEDs are red – the Analyzer cannot read the data. C. When only the PCB card is on – disconnect the cable from the motor unit and use the Analyzer
cable. D. When only the PCB led blinks with the Analyzer cable, it means that there are more than 3
Wall/Floor Sensor errors.
Press on the 'Test' button:
o If all LEDs are turning to green, the motor unit is ok. o If the PCB card led blinks, replace the PCB card.
E. If only four red LEDs blinking red it means that the motor unit is not ok. To determine and repair the defective part, open the motor unit cover and do as follows:
MU PCB card cable – the wires are marked with
DRV1, DRV2 & IMP.
Connect the MU PCB card cable to the PCB motor drivers socket
on the back of the Analyzer
The motors are marked
on the PCB card.
PCB led blinks
DIY Analyzer
Disconnect the motor wires from the PCB card. Connect the correct PCB card cable wires to the correct connections on the PCB card: Important Notes:
1. Do not disconnect the Dolphin’s floating cable from the Analyzer or from the motor unit while running the test.
2. Do not switch the Analyzer off before or during the test. 3. When connecting the cable to the PCB card, make sure the cover box is in a straight position and
not on its side. After making sure that all the cables are plugged in, press on the Analyzer’s “test” button. Wait a few seconds until the Analyzer has finished testing.
Replace the defective part and close the motor unit.
MU PCB card cable connected to the PCB card
Make sure the floating cable is connected to the Analyzer.
Make sure the floating cable is connected to the MU
Press “Test” to analyze for
the defective part. When the testing is complete, the LED representing the defective part
turns red. The other LEDs turn green.
The PCB card is
defective.
DIY Analyzer
3. Erasing the errors
Erasing the errors can be done only if the drive or impeller motor is needed to be replaced – press on the 'test' button for a few seconds while the motor unit is connected to the Analyzer and before testing it in the water.
4. Calibrating the Analyzer After 200 Analyzer tests, the Analyzer will not stop beeping, you need to calibrate the Analyzer.
Connect the MU PCB card cable and the MU cable into the back of the Analyzer and press 'test': Note: It is recommended to have the robot work in a testing pool or water tank for one full cycle to ensure everything is running properly.
If you have any questions, please contact us. We will be happy to help you.
Maytronics Technical department team
Connect the MU PCB card cable and the MU
cable into the back of the Analyzer
Press on the 'start'
button for a few seconds
The cables connected into the
back of the Analyzer
DIY Analyzer Novembre 2011
DIY Analyzer
Introduction Dans le cadre de notre engagement sur le marché des robots de piscine, Maytronics a développé Analyzer, un nouvel analyseur pour diagnostiquer les problèmes des unités motrices DIY. L'analyseur identifie les moteurs et cartes PCB défectueux, puis transfère ces données à un ordinateur. Il peut lire tous les types d'unités motrices Dolphin DIY, même celles installées sur les anciens modèles. Son utilisation permet de réduire considérablement les coûts de réparation. Panneau avant
Panneau arrière
Power supply – voyant marche/arrêt
de l'alimentation
Test – bouton de test
Drive motor 1 – test du moteur 1
Drive motor 2 – test du moteur 2
Impeller motor – test du moteur
de pompe
PCB card – test de la
carte PCB
USB Driver – connexion USB
Motor unit – connexion de
l'unité motrice
Battery – test de la batterie
On/Off – commutateur Marche/Arrêt
Motor unit – connexion entre l'Analyzer et
l'unité motrice
PCB motor drivers – connexion entre l'Analyzer et la carte PCB
de l'unité motrice
Self-test connections – connexions auto-test pour
réinitialiser l'Analyzer
PC – connexion entre l'Analyzer et l'ordinateur
Cordon d'alimentation
de l'Analyzer
DIY Analyzer
Mode d'emploi
1. Installation
Placer l'analyseur sur une surface propre et sèche. Connecter l'Analyzer avec votre ordinateur en branchant le câble de communication entre l'Analyzer et le port USB de votre ordinateur comme indiqué ci-dessous :
Brancher le cordon d'alimentation secteur à une alimentation électrique. Nous vous recommandons la nouvelle alimentation numérique Diagnostic 29 V : Remarque : Pour que l'Analyzer fonctionne, il doit être branché sur une alimentation.
Brancher le cordon d'alimentation à une
alimentation électrique.
Alimentation numérique
Connexion ordinateur
Connexion Analyzer
Brancher le câble à l'arrière de l'Analyzer
Brancher le câble sur le port USB de l'ordinateur
Brancher le cordon d'alimentation à une alimentation électrique.
Alimentation numérique
Commutation automatique
DIY Analyzer
Installer le logiciel de communication Analyzer PC sur votre ordinateur. Le logiciel se trouve sur la clé électronique fournie avec l'Analyzer. Pour installer le programme, enregistrer une copie du logiciel sur le bureau de votre ordinateur. Double-cliquer sur l'icône Setup :
Une nouvelle icône apparaîtra. Double-cliquer dessus : Double-cliquer sur « Next » sur les écrans de configurations qui s'affichent, puis double-cliquer sur « Close ».
Cliquer sur le bouton
« Close ».
DIY Analyzer
Lorsque l'installation du logiciel est terminée, un fichier nommé « Maytronics » apparaîtra sur votre bureau :
Double-cliquer sur le fichier « Maytronics » pour ouvrir le programme Analyzer. L'écran suivant apparaît :
Lorsque vous appuyez sur le bouton « Test » de l'Analyzer, les données de l'unité motrice sont affichées sur cet écran.
Remarque : Le programme Analyzer doit être ouvert sur votre ordinateur avant de lancer un test avec l'Analyzer.
DIY Analyzer
2. Procédures de test Le test Dolbox/scanner
Pour scanner l'unité motrice et afficher les données sur votre ordinateur , ouvrir le programme Analyzer et procéder comme suit :
A. Lorsque tous les voyants sont verts- l’unité motrice fonctionne correctement et l'Analyzer a terminé de collecter les données de l'unité motrice et les a envoyées au programme de l'Analyzer de votre ordinateur.
Les données dans le programme Analyzer
Imprimer le fichier
Enregistrer le fichier Attendre que tous les voyants soient verts.
Brancher le câble Amphenol du robot à la prise » de l'Analyzer, puis appuyer sur le Motor Unit «
». Test bouton « Les voyants rouges et verts clignotent pour
indiquer que l'analyseur collecte les données de
l'unité motrice et les envoie à votre ordinateur.
DIY Analyzer
B. Lorsque tous les voyants sont rouges - L’Analyzer ne peut pas lire les données. C. Lorsqu’uniquement la carte PBC est en marche – déconnecter le câble de l’unité motrice et
utiliser celui de l’Analyzer. D. Lorsque seuls les voyants du PCB clignotent avec le câble de l’Analyzer, cela signifie qu’il y a
plus de 3 erreurs de capteurs Mur/Sol.
Appuyer sur le bouton 'Test' :
Si tous les voyants deviennent verts, l’unité moteur est ok. Si le voyant de la carte PCB clignote, remplacez-la.
E. Si seuls 4 voyants rouges clignotent, cela signifie que l’unité motrice est défectueuse.
Pour identifier et réparer la pièce défectueuse, ouvrir le capot de l'unité motrice et procéder comme suit :
Les moteurs sont marqués
sur la carte PCB.
Câble de la carte PCB de l'unité motrice – les fils sont marqués
.DRV1, DRV2 et IMP
Brancher le câble de la carte PCB de l'unité motrice à la prise « PCB motor drivers » situé à l'arrière de l'Analyzer
PCB clignotent
DIY Analyzer
Débrancher les fils moteur de la carte PCB. Brancher correctement les fils du câble de la carte PCB aux fiches correspondantes de la carte PCB : Remarques importantes :
1. Ne pas débrancher le câble flottant robot de l'Analyzer ou de l'unité motrice lors du test. 2. Ne pas éteindre l'Analyzer avant ou pendant le test. 3. Lors du branchement du câble à la carte PCB, s'assurez que le couvercle de la boîte est droit et
non sur le côté. Après s'être assuré que tous les câbles sont branchés, appuyer sur le bouton « Test » de l'Analyzer. Attendre quelques secondes pour que l'Analyzer termine le test.
Remplacer la pièce défectueuse et refermer le capot de l'unité motrice.
Câble de la carte PCB de l'unité motrice branché sur la carte PCB
S'assurer que le câble flottant est branché à l'Analyzer.
S'assurer que le câble flottant est branché à l'unité motrice.
Appuyer sur « Test » pour lancer l'analyse
et identifier la pièce défectueuse.
La carte PCB est
défectueuse.
Lorsque le test est terminé, le voyant qui indique la pièce défectueuse devient
rouge. Les autres voyants sont verts.
DIY Analyzer
3. L'effacement des erreurs
L'effacement des erreurs ne doit se faire que lors du changement de l'un des moteurs. Appuyer alors sur le bouton « test » pendant quelques secondes avec l'unité motrice branchée à l'analyseur et avant de le tester dans l'eau.
4. l'arrière de l'Analyzer Après 200 tests, l'Analyzer émettra continuellement des « bips ». Il devra alors être étalonné. Brancher le câble de la carte PCB de l'unité motrice et le câble de l'unité motrice à l'arrière de l'Analyzer, puis appuyer sur le bouton « Test » :
Remarque : 1. Il est recommandé de faire fonctionner le robot dans une piscine ou un réservoir d'eau pendant
un cycle complet pour s'assurer que tout fonctionne correctement.
Veuillez nous contacter pour toute question. Nous serons heureux de vous aider.
L'équipe du Service technique de Maytronics
Brancher le câble de la carte PCB de l'unité motrice et le câble de l'unité motrice à l'arrière de
l'Analyzer
Appuyer sur le bouton « Test » pendant quelques
secondes
Câbles branchés à l'arrière de l'Analyzer
DIY Analyzer November 2011
DIY Analyzer
Einführung Als Teil unseres Engagements im Roboter-Poolreinigungs-Markt, hat Maytronics einen neuen Analyzer entwickelt, um Probleme in den DIY Motoreinheiten festzustellen. Der Analyzer erkennt defekte Motoren und PCB-Karten und überträgt die Daten an einen Computer. Er kann jede Art von Dolphin DIY Motoreinheit lesen, auch solche, die in alten Modellen verbaut sind. Durch den Einsatz des Analyzers können die Reparaturkosten deutlich gesenkt werden. Frontplatte
Rückenplatte
Power supply On/Off LED
Test Taste
Drive motor 1 Test
Drive motor 2 Test
Impeller motor Test
PCB card Test
Speicher-stick-
Eingang
Motor unit Kabel-
eingang
Batterietest
on/off Schalter
Kabelverbindung zwischen motor
unit und Analyzer
Kabelverbindung zwischen Analyzer und
motor unit PCB card
Self-test connections zur Rückstellung des Analyzers
Kabelverbindung zwischen Computer
und Analyzer
Hauptstromkabel – zwischen Analyzer und
Netztteil
DIY Analyzer
Bedienungsanleitung
1. Set-up
Stellen Sie den Analyzer auf eine saubere und trockene Oberfläche. Verbinden Sie den Analyzer mit Ihrem PC, indem Sie ihn mit dem Verbindungskabel an den USB-Port Ihres Computers, wie unten dargestellt, anschließen:
Stecken Sie den Netzstecker in eine Steckdose. Wir empfehlen das neue diagnostische 29V digitale Schaltnetzteil:
Verbinden Sie den Netzstecker mit der
Steckdose
Digitales Schaltnetzteil
Verbinden Sie den Netzstecker mit der
Steckdose
Digitales Schaltnetzteil
Stecken Sie das Kabel in den PC-USB-Port.
Anschluss an den PC
Anschluss an den
Analyzer
Stecken Sie das Kabel in die Rückseite des
Analyzers
DIY Analyzer
Anmerkung: Damit der Analyzer funktioniert, muss er an die Stromversorgung angeschlossen werden. Installieren Sie die Analyzer PC-Kommunikations-Software auf Ihrem Computer. Die Software wird auf einem USB-Speicherstick mit dem Analyzer geliefert. Um das Programm zu installieren, speichern Sie eine Kopie der Software auf Ihrem Computer-Desktop. Doppelklicken Sie auf auf das Set-up-Symbol:
Es erscheint ein neues Symbol. Doppelklicken Sie darauf: Doppelklicken Sie auf den Set-up-Dialogfeldern auf “Next” und dann auf “Close”.
Drücken Sie die 'Close'-
Taste.
DIY Analyzer
Wenn die Software-Installation abgeschlossen ist, erscheint eine Datei mit dem Namen "Maytronics” auf Ihrem Bildschirm:
Doppelklicken Sie auf die “Maytronics”-Datei, um das Analyzer-Programm zu öffnen. Das folgende Dialogfenster erscheint:
Wenn Sie auf die “Test”-Taste des Analyzers drücken, erscheinen die Daten zur Motoreinheit auf diesem Bildschirm.
Anmerkung: Das Analyzer-Programm muss auf Ihrem Computer geöffnet sein, bevor ein Test mit dem Analyzer durchgeführt werden kann.
DIY Analyzer
2. Testverfahren Der Dolbox/Scanner-Test
Um die Motoreinheit zu scannen und die Daten auf Ihrem Computer anzuzeigen, öffnen Sie das Analyzer-Programm und gehen wie folgt vor:
A. Wenn alle LEDs grün aufleuchten – ist die Motoreinheit ok; der Analyzer hat die Datenerfassung der Motoreinheit abgeschlossen und diese an das Analyzer-Programm auf Ihrem Computer weitergeleitet.
Warten Sie bis alle LEDs grün geworden sind.
Die Daten im Analyzer-Programm
Print file
Save file
Verbinden Sie das Dolphin-Kabel Amphenol mit der Analyzer Motoreinheits-Steckdose und
drücken Sie auf “Test.” Die roten und grünen LEDs leuchten auf, um
anzuzeigen, dass der Analyzer Daten vom MU sammelt und sie an Ihren Computer sendet.
DIY Analyzer
B. Wenn alle LEDs des Analyzers rot aufleuchten – kann der Analyzer die Daten nicht lesen. C. Wenn nur die PCB-Karte aufleuchtet – das Kabel von der Motoreinheit lösen und das Analyzer-
Kabel verwenden. D. Wenn nur die PCB-LED Lampe mit dem Analyzer-Kabel aufleuchtet, bedeutet dies mehr als 3
Wand/Boden Sensor-Fehler.
Drücken Sie auf die "Test"-Taste:
Wenn alle LEDs Grün aufleuchten, ist die Motor Einheit in Ordnung. Wenn die LED der PCB Karte blinkt, ersetzen Sie die PCB Karte.
E. Wenn nur vier rote LEDs rot aufleuchten, bedeutet das, dass die Motoreinheit nicht ok ist. Um das defekte Teil festzustellen und zu reparieren, öffnen Sie die Motoreinheit und gehen wie folgt vor:
Die Motoren sind auf der PCB-Karte
markiert.
MU PCB-Karten-Kabel – die Drähte sind mit DRV1,
DRV2 & IMP markiert.
Verbinden Sie das MU PCB Karten-Kabel mit der PCB Motor-
Treiber-Steckdose auf der
Rückseite des Analyzers
PCB led blinks
DIY Analyzer
Trennen Sie die Motor-Drähte von der PCB-Karte. Verbinden Sie die korrekten PCB-Karten-Kabel mit den korrekten Anschlüssen auf der PCB-Karte: Wichtige Anmerkungen:
1. Trennen Sie das Dolphin-Schwimmkabel nicht vom Analyzer oder von der Motoreinheit solange der Test läuft.
2. Schalten Sie den Analyzer nicht vor oder während des Tests aus. 3. Wenn Sie das Kabel mit der PCB-Karte verbinden, stellen Sie sicher, dass sich der Kastendeckel in
aufrechter Position und nicht seitlich befindet. Wenn Sie sichergestellt haben, dass alle Kabel eingesteckt sind, drücken Sie auf die “Start”-Taste des Analyzers. Warten Sie einige Sekunden bis der Analyzer den Test beendet hat. Ersetzen Sie das defekte Teil und schließen Sie die Motoreinheit.
MU PCB Karten-Kabel verbunden mit der PCB-
Karte
Stellen Sie sicher, dass das Schwimmkabel mit dem
Analyzer verbunden ist.
Stellen Sie sicher, dass das Schwimmkabel mit dem MU
verbunden ist
Drücken Sie auf "Test”, um das defekte Teil zu
analysieren.
Die PCB-Karte ist
defekt.
Wenn der Test beendet ist, leuchtet die LED-Lampe, die das defekte Teil anzeigt, rot auf. Die anderen LEDs
leuchten grün.
DIY Analyzer
3. Fehler melding loschen: Fehler können nur dann beseitigt werden, wenn der Antrieb oder Impeller-Motor ersetzt werden muss – drücken Sie einige Sekunden auf die 'Test'-Taste während die Motoreinheit mit dem Analyzer verbunden wird und bevor Sie sie im Wasser testen.
4. Analyzer kalibrieren Nach 200 Analyzer-Tests piept der Analyzer ununterbrochen, Sie müssen den Analyzer kalibrieren. Stecken Sie das MU PCB-Kartenkabel und das MU-Kabel an der Rückseite des Analyzer ein und drücken Sie auf 'Test': Anmerkungen:
1. Es wird empfohlen, mit dem Roboter zunächst in einem Test-Pool oder einem Wassertank einen vollständigen Zyklus durchzuführen, um sicherzustellen, dass er einwandfrei funktioniert.
Bei Fragen setzen Sie sich bitte mit uns in Verbindung. Wir stehen Ihnen gern zur Verfügung.
Ihr Maytronics Team der Technischen Abteilung
Stecken Sie das MU PCB-Kartenkabel und das MU-Kabel an der Rückseite des Analyzer ein
Drücken Sie einige Sekunden auf den 'Start'-
Knopf
Die auf der Rückseite des
Analyzer
eingesteckten Kabel
DIY Analyzer Novembre 2011
DIY Analyzer
Introduzione A prova del proprio impegno nel settore della pulizia robotica per piscina, Maytronics ha introdotto un nuovo Analyzer per diagnosticare problemi nei motori DIY (“fai da te”)
L’Analyzer identifica motori e schede elettroniche difettose e invia questi dati ad un computer. È in grado di analizzare tutti i tipi di blocco motore Dolphin DIY, anche
quelli installati nei vecchi modelli. Grazie all’Analyzer, i costi di riparazione possono essere ridotti sensibilmente.
Panello anteriore
Panello posteriore
Pulsante on/off button
Connessioni cavo tra Analyzer
e blocco motore (motor unit)
Connessioni cavo tra Analyzer
e circuito blocco motore (motor unit PCB card)
Self-test connections per resettare Analyzer
Connessioni cavo tra computer e Analyzer
Cavo alimentazione – tra Analyzer e alimentatore
Luci alimentatore (power supply)
on/off
Pulsante “Test”
Test del motore di trazione
(drive motor) 1
Test del motore di trazione
(drive motor) 2
Test del motore pompa (impeller
motor)
Test della scheda
elettronica (PCB card)
Presa USB
Presa cavo blocco motore (motor unit)
Test batteria (battery)
DIY Analyzer
Istruzioni per l'uso
1. Installazione
Posizionare l’Analyzer su una superficie pulita ed asciutta. Collegare l’Analyzer al computer inserendo il cavo connettore nell’Analyzer nella porta USB del vostro computer come nelle illustrazioni:
Inserire il cavo di alimentazione nel trasformatore. Raccomandiamo il nuovo trasformatore digitale Diagnostic 29V: Nota: Collegare l'Analyzer ad un trasformatore per farlo funzionare.
Collegamen-
to al PC
Collegamento
all’Analyzer
Inserire il cavo nella porta USB del PC
Inserire il cavo sul retro dell'Analyzer
Collegare il cavo al trasformatore
Trasformatore digitale “switch-
mode”
Collegare il cavo al trasformatore
Trasformatore digitale
DIY Analyzer
Installare il software di trasmissione Analyzer sul vostro computer. Il software si trova sulla chiave USB fornita insieme all’Analyzer. Per installare il programma, salvare una copia del software sul desktop del computer. Cliccare due volte sulla icona “installazione” (set-up):
Comparirà una nuova icona. Cliccare due volte: Cliccare due volte “Next” sulla schermata di installazione e poi cliccare due volte “Close”.
Cliccare
“Close”.
DIY Analyzer
Quando l'installazione del software è stata completata, sul desktop apparirà un file chiamato “Maytronics” :
Cliccare due volte sul file “Maytronics” per aprire il programma Analyzer. Apparirà questa schermata:
Quando verrà premuto il pulsante “Test” sull’Analyzer, i dati del blocco motore (MU, motor unit) appariranno su questo schermo.
Nota: Il programma Analyzer deve essere aperto sul computer prima di avviare un test con l’Analyzer.
DIY Analyzer
2. Procedura del test The Dolbox/scanner test
Per analizzare il blocco motore e visualizzare i dati sul computer, aprire il programma Analyzer e procedere nel modo seguente:
A. Quando tutte le luci LED sono verdi - il blocco motore è ok e l’Analyzer ha terminato la raccolta dei dati del blocco motore e li ha inviati al programma Analyzer sul computer.
I dati nel programma Analyzer
Stampa file
Salva file Attendere che le luci LED siano verdi.
Collegare la presa Amphenol del cavo di Dolphin alla presa “motor unit” che si
trova sull’Analyzer e premere “Test.”
Le luci LED lampeggiano rosse e verdi per indicare che l’Analyzer sta raccogliendo i dati dal blocco
motore e li sta inviando al computer
DIY Analyzer
B. Quando tutte le luci LED sono rosse – l’Analyzer non può analizzare i dati. C. Quando resta acceso solo il LED della scheda elettronica (PCB card) – staccare il cavo dal blocco
motore e usare il cavo dell’Analyzer. D. Quando lampeggia solo il LED della scheda elettronica con il cavo dell’Analyzer, vuol dire che ci
sono più di 3 errori del sensore Parete/Pavimento.
Premere il pulsante 'Test':
Se tutti i LED diventano verdi, l'unità motore è funzionante. Se il LED della scheda PCB lampeggia, sostituire la scheda PCB.
E. Se lampeggiano solo quattro luci LED rosse, vuol dire che il blocco motore non è ok.
Per individuare e riparare il componente difettoso, aprire il coperchio del blocco motore e procedere nel modo seguente:
I motori sono indicati sulla scheda
Cavo del circuito del blocco
motore – i fili sono contrassegnati DRV1, DRV2 &
IMP.
Collegare il cavo della scheda del blocco motore alla presa
“PCB motor drivers” sul retro
dell'Analyzer
PCB led blinks
DIY Analyzer
Staccare i fili del blocco motore dalla scheda. Collegare i fili del cavo della scheda elettronica agli appropriati connettori sulla scheda: Importante:
1. Non scollegare il cavo galleggiante Dolphin dall'Analyzer o dal blocco motore mentre il test è in corso.
2. Non spegnere l’Analyzer prima del test o mentre il test è in corso. 3. Quando il cavo viene collegato alla scheda elettronica, assicurarsi che il coperchio sia diritto e
non sul lato. Dopo aver verificato che i tutti cavi siano inseriti, premere il pulsante “test” dell’Analyzer. Attendere alcuni secondi finché l’Analyzer avrà completato il test.
Sostituire il componente difettoso e chiudere il blocco motore.
Accertarsi che il cavo galleggiante sia collegato
al blocco motore.
Cavo della scheda del blocco motore collegato
alla scheda.
Accertarsi che il cavo galleggiante sia collegato
all’Analyzer.
La scheda è difettosa.
Quando il test sarà completato, la luce LED corrispondente al
componente difettoso diventerà rossa. Le altre luci LED
diventeranno verdi.
Premere il pulsante “Test” per individuare il
componente difettoso.
DIY Analyzer
3. È possibile cancellare gli errori
È possibile cancellare gli errori solo se si sostituisce il motore di trazione o il motore pompa – premere il pulsante 'test' per qualche secondo con il blocco motore collegato all’Analyzer, prima di provarlo in acqua.
4. L’ Analyzer dovrà essere calibrato
Dopo 200 test, l’Analyzer emetterà un segnale acustico continuo. L’ Analyzer dovrà essere calibrato. Collegare il cavo della scheda del blocco motore e il cavo del blocco motore sul retro dell’Analyzer e premere 'test':
Nota: 1. Si raccomanda di eseguire un intero ciclo di pulizia con il robot in una piscina o in una vasca di
prova per assicurarsi del funzionamento di tutti i componenti.
Per qualsiasi domanda, contattateci. Saremo felici di aiutarvi.
Reparto tecnico Maytronics
Collegare il cavo della scheda del blocco motore e il cavo del blocco motore sul retro
dell’Analyzer
Cavi connessi sul
retro dell’ Analyzer Premere il pulsante 'start'
per qualche secondo
DIY Analyzer Noviembre de 2011
DIY Analyzer
Introducción Como parte de nuestro compromiso con el mercado de limpiadores de piscina robóticos, Maytronics ha desarrollado un nuevo Analyzer para diagnosticar problemas en unidades motoras DIY. El Analyzer identifica motores defectuosos y tarjetas PCB y transfiere los datos a un sistema informático. Puede leer todos los tipos de unidades motoras Dolphin DIY, incluso las instalados en modelos antiguos. Gracias al uso del Analyzer, pueden reducirse los costes de reparación de forma significativa. Panel frontal
Panel trasero
LED on/off
Power supply
Botón
Test
Test Drive motor 1
Test Drive motor 2
Test Impeller
motor
Test PCB
card
Entrada de disco usb
Entrada de cable de
Motor unit cable entry
Prueba Battery
Botón on/off
Conexión del cable entre motor unit y el Analyzer
Conexión del cable entre el Analyzer y
motor unit PCB card
Self-test connections para
reiniciar el Analyzer Conexión del cable
entre el ordenador y el Analyzer
Cable de suministro principal entre el
Analyzer y el
suministro eléctrico
DIY Analyzer
Instrucciones de funcionamiento
1. Configuración
Coloque el Analyzer sobre una superficie limpia y seca. Conecte el Analyzer a su PC conectando el cable de comunicaciones entre el Analyzer y el puerto USB de su ordenador como se indica a continuación:
Conecte el cable de alimentación a la fuente de alimentación. Recomendamos el nuevo interruptor de alimentación en modo digital Diagnostic 29V: Nota: Para que el Analyzer funcione tiene que estar conectado a una fuente de alimentación.
Conexión a PC
Conexión al Analyzer
Conecte el cable al puerto USB del PC
Conecte el cable en la parte posterior del
Analyzer
Conecte el cable de alimentación a la fuente
de alimentación
Fuente de alimentación con
conmutador digital
Conecte el cable de alimentación a la fuente
de alimentación
Fuente de alimentación con
conmutador digital
DIY Analyzer
Instale el software de comunicación de Analyzer PC en su ordenador. El software está en el disk-on-key que viene con el Analyzer. Para instalar el programa, guarde una copia del software en el escritorio de su ordenador. Haga doble clic en el icono:
Aparecerá un nuevo icono. Haga doble clic en el icono:
Haga doble clic en “Next” en las pantallas de instalación y a continuación haga doble clic
en "Close”.
Pulse el botón
'Close'.
DIY Analyzer
Cuando el software de instalación se ha completado, un archivo denominado “Maytronics” aparecerá en el escritorio:
Haga doble clic en el archivo de “Maytronics” para abrir el programa Analyzer. Aparecerá
la siguiente pantalla:
Cuando se pulsa el botón "Test" del Analyzer aparece en la pantalla la unidad motora.
Nota: El programa Analyzer debe estar abierto en su ordenador antes de ejecutar una prueba con el Analyzer.
DIY Analyzer
2. Procedimientos de ensayo Test escáner/Dolbox
Para explorar la unidad motora y mostrar los datos en su ordenador, abra el programa Analyzer y haga lo siguiente:
A. Cuando todos los LED estén en verde, la unidad motora está correcta y el Analyzer ha concluido la recopilación de datos de la unidad motora y los ha enviado al programa Analyzer en su ordenador.
Espere hasta que todos los LED estén en verde.
Datos que figuran en el programa Analyzer
Print file
Save file
Conecte el cable Dolphin Amphenol al enchufe de la unidad motora del Analyzer y
pulse “Test.”
Los LED rojo y el verde señalan que el Analyzer está recogiendo datos de la UM y
enviándolos a su equipo.
DIY Analyzer
B. Cuando todos los LED están en rojo, el Analyzer no puede leer los datos. C. Cuando solo la tarjeta PCB está activada, desconecte el cable de la unidad motora y use el cable
del Analyzer. D. Cuando solo parpadea el led del PCB con el cable del Analyzer, significa que hay más de 3
errores Wall/Floor Sensor.
Pulse el botón 'Test':
Si todos los led aparecen en verde, la unidad motora está correcta. Si parpadea la tarjeta PCB, reemplace la tarjeta PCB.
E. Si solo cuatro LEDs rojos parpadean en rojo, significa que la unidad motora no está correcta.
Para determinar y reparar la pieza defectuosa, abra la tapa de la unidad motora cubrir y haga lo siguiente:
Conecte el cable de su tarjeta MU PCB al enchufe de los drivers
del motor PCB en la parte posterior del Analyzer
Cable de tarjeta MU PCB – los cables están marcados
con DRV1, DRV2 & IMP.
Los motores están marcadas en la tarjeta
PCB.
PCB led blinks
DIY Analyzer
Desconecte los cables del motor desde la tarjeta PCB. Conecte el cable correcto de la tarjeta PCB a las conexiones correctas de la tarjeta PCB: Notas importantes:
1. No desconecte el Dolphin’s floating cable del Analyzer o de la unidad motora mientras se ejecuta el test.
2. No desconecte el Analyzer antes o durante el test. 3. Cuando se conecta el cable a la tarjeta PCB, asegúrese de que la tapa de la caja se encuentra en
una posición recta y no lateral. Después de asegurarse de que todos los cables están conectados, pulse el botón “test” del Analyzer. Espere unos segundos hasta que el Analyzer termine la prueba.
Sustituya la pieza defectuosa y cierre la unidad motora.
El cable de la tarjeta MU PCB está conectado a la a
tarjeta PCB
Asegúrese de que el floating cable está conectado al
Analyzer.
Asegúrese de que el floating cable está conectado al la
UM.
La tarjeta PCB está
defectuosa.
Pulse “Test” para el análisis
de la pieza defectuosa.
Cuando termine la prueba, el LED de la pieza defectuosa aparecerá en rojo. Los otros LED aparecen en
verde.
DIY Analyzer
3. El borrado de errores
El borrado de errores solo puede hacerse si el motor o turbina se necesita ser reemplazado. Pulse el botón "test" durante unos segundos mientras la unidad de motora está conectada al Analyzer y antes de la prueba en el agua.
4. calibrar el Analyzer
Después 200 pruebas el Analyzer no dejará de sonar. Necesitará calibrar el Analyzer. Conecte el cable de su tarjeta MU PCB al cable del MU en la parte posterior del Analyzer y pulse en "test".
Note:
1. Se aconseja hacer funcionar al robot en una piscina de prueba o tanque de agua durante un ciclo completo para asegurarse de que todo funcione correctamente.
Para más información, le rogamos se ponga en contacto con nosotros. Estaremos encantados de ayudarle.
El equipo del Departamento Técnico de Maytronics
Conecte el cable de su tarjeta MU PCB al cable del MU en la parte posterior del
Analyzer
Cables conectados en la parte posterior
del Analyzer
Pulse el botón "start" (inicio) durante unos
segundos