Dishwasher Sn64e005eu instruction for use.pdf

8/10/2019 Dishwasher Sn64e005eu instruction for use.pdf

1/40

SNSX


2/40


3/40

en

3

Table of contents

8Intended use . . . . . . . . . . . . . . . 4

(Safety instructions . . . . . . . . . . 4Before you switchON the appliance . . . . . . . . . . . . . . . . 4

Delivery. . . . . . . . . . . . . . . . . . . . . . . . 5

Installation. . . . . . . . . . . . . . . . . . . . . . 5

In daily use . . . . . . . . . . . . . . . . . . . . . 6

Door lock. . . . . . . . . . . . . . . . . . . . . . 6

Damage. . . . . . . . . . . . . . . . . . . . . . . 6

Disposal. . . . . . . . . . . . . . . . . . . . . . . 7

7Protection ofthe environment . . . . . . . . . . . . 8

Packaging. . . . . . . . . . . . . . . . . . . . . . 8

Old appliances . . . . . . . . . . . . . . . . . . 8

*Getting to knowyour appliance. . . . . . . . . . . . . . 9

Control panel . . . . . . . . . . . . . . . . . . . 9

Appliance interior. . . . . . . . . . . . . . . . 9

+Water softening system/Special salt . . . . . . . . . . . . . . . . 9

Setting . . . . . . . . . . . . . . . . . . . . . . . 10

Water hardness table . . . . . . . . . . . . 10

Using special salt . . . . . . . . . . . . . . . 10

Detergents with salt component . . . . 11

Switching off

water softening system . . . . . . . . . . . 11

,Rinse aid . . . . . . . . . . . . . . . . . 11Setting amount of rinse aid. . . . . . . . 12

Switching offrinse-aid refill indicator. . . . . . . . . . . 12

-Utensils . . . . . . . . . . . . . . . . . . 12Not suitable . . . . . . . . . . . . . . . . . . . 12

Glass and utensil damage. . . . . . . . 12

Loading the dishwasher. . . . . . . . . . 13

Unloading the dishwasher . . . . . . . . 13

Cups and glasses. . . . . . . . . . . . . . . 13

Pans . . . . . . . . . . . . . . . . . . . . . . . . . 14Cutlery basket. . . . . . . . . . . . . . . . . . 14

Etagere . . . . . . . . . . . . . . . . . . . . . . . 14

Folding spikes . . . . . . . . . . . . . . . . . 15

Small accessories holder. . . . . . . . . 15

Knife shelf . . . . . . . . . . . . . . . . . . . . . 15

Adjusting the heightof the basket. . . . . . . . . . . . . . . . . . . 15

.Detergent . . . . . . . . . . . . . . . . . 16Adding detergent . . . . . . . . . . . . . . . 17

Combination detergent . . . . . . . . . . . 17

/Overview of programmes . . . . 19Programme selection. . . . . . . . . . . . 20

Information for test institutes . . . . . . . 20

0Additional options . . . . . . . . . . 20Express Wash/ Speed Perfect(VarioSpeed). . . . . . . . . . . . . . . . . . . 20

Intensive zone . . . . . . . . . . . . . . . . . . 20

Hygiene. . . . . . . . . . . . . . . . . . . . . . . 20

Half load . . . . . . . . . . . . . . . . . . . . . . 20

Extra drying. . . . . . . . . . . . . . . . . . . . 20

1Operating the appliance . . . . . 21Programme data . . . . . . . . . . . . . . . .21

Aqua sensor . . . . . . . . . . . . . . . . . . . 21Switching on the appliance . . . . . . . . 21

Optical display whilethe programme is running . . . . . . . . 21

Timer programming . . . . . . . . . . . . . 22

End of programme. . . . . . . . . . . . . . 22

Interrupting the programme . . . . . . . 23

Terminating the programme . . . . . . . 23

Changing the programme. . . . . . . . . 23

Intensive drying. . . . . . . . . . . . . . . . . 23


4/40

en Intended use

4

2Cleaning and maintenance. . . 24Overall condition of the machine . . . 24

Special salt and rinse aid . . . . . . . . . 24

Filters. . . . . . . . . . . . . . . . . . . . . . . . 25

Spray arms . . . . . . . . . . . . . . . . . . . . 25

3Fault, what to do? . . . . . . . . . . 26Waste water pump. . . . . . . . . . . . . . 26

Fault table. . . . . . . . . . . . . . . . . . . . . 27

4Customer service . . . . . . . . . . 345Installation and connection . . 34Product package . . . . . . . . . . . . . . . 35

Safety instructions. . . . . . . . . . . . . . . 35

Delivery. . . . . . . . . . . . . . . . . . . . . . . 35

Technical specifications. . . . . . . . . . 35

Installation. . . . . . . . . . . . . . . . . . . . . 36

Waste-water connection. . . . . . . . . . 36

Drinking water connection . . . . . . . . 36

Electrical connection. . . . . . . . . . . . . 37

Removing the appliance . . . . . . . . . . 37

Transportation. . . . . . . . . . . . . . . . . . 38Protection against frost(Emptying the appliance). . . . . . . . . 38

8Intended useIntended use

This appliance is intended foruse in the home and

the home environment. Use the dishwasher

only in the householdand only for its designedpurpose: for washingdomestic dishes.

(Safety instructionsSafety instructions

Children from 8 years of ageor people whose physical,sensory or mental abilitiesor their lack of experienceor knowledge prevent them

from using the appliance safelymust not use this appliancewithout supervisionor instruction by a responsibleperson.

Before you switch ONthe appliance

Please read the operatingand installation instructionscarefully. They containimportant information on how toinstall, use and maintainthe appliance.

Retain all documents forsubsequent use or for the next

owner.


5/40

Safety instructions en

5

Delivery

1. Check the packaging anddishwasher immediately fordamage caused in transit. Donot switch on a damagedappliance, but contact yoursupplier.

2. Please dispose of thepackaging material in anenvironmentally friendlymanner.

3. Do not let children play with

packaging and its parts.There is a risk of suffocationfrom collapsible boxes andfilm.

Installation

Following installation, ensurethat the backof the dishwasher is notfreely accessible (protectionagainst contact due to hotsurface).

Install and connectthe appliance accordingto the installationand assembly instructions.

Prior to installation,disconnect the dishwasherfrom the power supply.

Ensure that the protectiveconductor systemof the domestic supply hasbeen correctly installed.

The electrical connectionconditions must correspondwith the specificationson the dishwasher ratingplate 92.

If the power cord of thisappliance is damaged,it must be replaced witha particular power cord.

To prevent injury, the powercord may be purchased fromcustomer service only.

If the dishwasher is installed

in a high-sided unit, the unitmust be secured properly.

If the dishwasher is installedbelow or above otherdomestic appliances, followthe information for installationin combination witha dishwasher

in the installation instructionsfor the particular appliances.

Also follow the installationinstructions forthe dishwasher to ensurethat all appliances areoperated safely.

If there is no information or ifthe installation instructions

do not includethe appropriate information,contact the manufacturerof these appliancesto ensure thatthe dishwasher can beinstalled above or belowthese appliances.


6/40

en Safety instructions

6

If you cannot obtain anyinformation fromthe manufacturer, you mustnot install the dishwasherabove or below theseappliances.

If you install a microwaveoven above the dishwasher,the microwave oven may bedamaged.

Install built-underor integratable appliancesonly under continuous

worktops which have beenscrewed to adjacentcupboards to ensure stability.

Do not install the appliancenear heat sources (radiators,heat storage tanks, cookersor other appliances whichgenerate heat) and do notinstall under a hob.

After installing the appliance,ensure that the plug is easilyaccessible.

(See Electrical connection)

Some models:

The plastic housing on thewater connection containsan electric valve,the connecting cablesare in the supply hose.Do not cut through this hose,do not immerse the plastichousing in water.

In daily use

Read and observe the safetyinformation and instructionsfor use on the packagingfor cleaning and rinsing agents.

Childproof lock(door lock)Door l ock*

The description of thechildproof lock is at the back inthe envelope.

* depending on model

Damage

The appliance may berepaired and opened up by atechnician only. To do this,disconnect the appliance

from the power supply. Pullout the mains plug or switchoff the fuse. Turn off the tap.

If the appliance is damaged,especially the fascia (cracks,holes, broken buttons), or thedoor function is impaired,stop operating the appliance.Pull out mains plug or switch

off fuse. Turn off tap, callcustomer service.


7/40

Safety instructions en

7

Disposal

1. Make redundant appliancesunusable to preventsubsequent accidents.

2. Dispose of the appliance in an environmentally friendlymanner.

m WarningRisk of injury!

To prevent injuries, e.g.

caused by stumbling, openthe dishwasher only brieflyin order to load and unloadthe dishwasher.

Knives and other utensilswith sharp points must beplaced in the cutlery basketwith the pointsdownwards or horizontally on

the knife shelf*. Do not lean or sit

on the open door. In the case of free-standing

appliances, ensure that thebaskets are not overloaded.

If the applianceis not in a cavity and a sidepanel is accessible, the doorhinge area must be coveredat the sidefor reasons of safety(risk of injury). The coversare available as optionalaccessories from customerservice or specialist outlets.


m WarningRisk of explosion!

Do not add any solventsto the washing chamber.

Danger of explosion!

m WarningRisk of scalding!

Open the door carefully whenthe programme is still running.There is a risk of hot waterspraying out of the appliance.

m WarningRisks to children!

If fitted, use the childprooflock. An exact descriptioncan befound in the back of the envelope.

Do not allow children to playwith or operatethe appliance.

Keep children away fromdetergents and rinse aid.These may cause chemicalburns in the mouth, throatand eyes or asphyxiation.

Keep children away fromopen dishwasher.The water in the rinsingcompartment is not drinkingwater and could containdetergent residue.


8/40

en Protection of the environment

8

Ensure that children do notplace fingers in the tabletcollecting tray 12. Smallfingers could becomecaught in the slots.

When opening and closingthe door on an eye-levelappliance, ensure thatchildren do not becomejammed or crushed betweenthe appliance door and thecupboard door below.

Children could become

locked in the appliance(danger of suffocation) or getinto another dangeroussituation.Redundant appliances: Pullout the mains plug, severand dispose of the powercord. Destroy the door lockso that the door can no

longer be closed.

7Protection of theenvironment

Protection ofthe environment

Both the packaging of new appliances

and the old appliances themselvescontain valuable raw materialsand recyclable materials.

Please dispose of the individual partsseparated according to type.

Please ask your dealer or inquire at yourlocal authority about current meansof disposal.

Packaging

All plastic parts of the appliance areidentified with internationallystandardised abbreviations (e.g. >PS Pand pressSTART buttonhuntil the drydisplay`and salt refillindicator )*flash.

4. Release buttons.

5. Keep pressing button > Puntilthe rinse aid refill indicator )"flashes.

The rinse aid refill indicator )"flashes and the displays #and+are lit (= Setting 2).

To change the setting:

1. Press the button


13/40

Utensils en

13

Recommendation:

Use only glasses and porcelainwhich the manufacturer designatesas dishwasher-proof.

Use a detergent which protects

utensils. Take glass and cutlery out of the

dishwasher as soon as possible afterthe programme ends.

Loading the dishwasher

1. Remove large food remnants. It isnot necessary to prerinse utensilsunder running water.

2. Place the utensils so that

they are secure and cannot tipover.

all utensils with their openingsface down.

parts with curves or indentationsare at an angle, thereby allowingwater to drain.

does not obstruct rotation of the

two spray arms 1:and 1B.Very small utensils should not bewashed in the machine, as they may fallout of the baskets.

Unloading the dishwasher

To prevent water from dripping off theupper basket onto the utensils in the

lower basket, it is recommendedto empty the appliance from the bottomup.

Hot utensils are sensitive to shock!Therefore, when the programme ends,leave the utensils to cool down in thedishwasher until they can be handled.

Note

When the programme ends, water

droplets can still be seen insidethe appliance. This does not affectthe drying of the utensils.

Cups and glasses

Top basket 1"

Note

Utensils must not be placed above thetablet collecting tray 12. These mayblock the lid of the detergent dispenser

and prevent it from opening fully.


14/40

en Utensils

14

Pans

Bottom basket 1b

Tip

Heavily soiled utensils (pans) shouldbe placed in the bottom basket. Themore powerful spray jet provides

a better dishwashing result.Tip

Other examples, such as the best wayof loading your dishwasher, canbe found on our homepage as a freedownload. The corresponding Internetaddress can be found on the back pageof these instructions for use.

Cutlery basket

You should always place cutleryunsorted with the points downwards.

To prevent injuries, place long, pointed

implements and knives on the knifeshelf.

Et agereEtagere *

The etagere and the space underneathcan be used for small cups and glassesor for larger items of cutlery, such as

wooden spoons or serving cutlery. Theetagere can be folded up if not required.

* Depending on the model, a 3-foldheight adjustment is possible. To dothis, first place the etagere verticallyand pull up, then place at a slight angle,push down to the required height (1, 2,or 3) and snap into place.


15/40


16/40

en Detergent

16

Top basket with side levers

1. Pull out the top basket 1"out.

2. To lowerthe basket, press in the leftand then the right lever on the

outside of the basket. In doing so,hold the sides of the basket alongthe upper edge to prevent it fromsuddenly dropping.

3. Toraisethe basket, hold the basketon the sides of the upper edge andlift it up.

4. Before re-inserting the basket again,ensure that it is at the same heighton both sides. Otherwise, theappliance door cannot be closedand the upper spray arm will not beconnected to the water circuit.

Top basket with upper andlower roller pairs

1. Pull out the top basket 1"out.

2. Remove the upper basket and re-attach it to the upper (stage 3) orlower (stage 1) rollers.

.DetergentDetergent

You can use tablets as well as powderor liquid detergents for dishwashers, but

never use washing up liquid.The dosage can be individually adjustedwith powder or a liquid detergentaccording to the degree of soiling.Tablets contain an adequately largeamount of active ingredientsfor all cleaning tasks. Modern, powerfuldetergents predominantly use a low-alkaline formulation with phosphateand enzymes. Phosphates bondthe lime in the water. Enzymes break

down starch and remove protein.Phosphate-free detergents are lessfrequent. These have a slightly weakerlime bonding capacity and requirea higher dosage. To remove colouredstains (e.g. tea, tomato sauce), oxygen-based bleaching agents are usuallyused.

Note

To ensure a good washing result,always follow the instructionson the detergent packaging!If you have further questions,we recommend that you contactthe detergent manufacturers helpline.

m Warning Read and observe thesafety information and instructions foruse on the packaging for cleaning andrinsing agents.


17/40

Detergent en

17

Adding detergent

1. If the detergent dispenser 9"is stillclosed, press the lock 9*to openthe detergent dispenser.

Pour detergent into the dry detergentdispenser 9"only (insert tablet flat,not on its edge).Dosage: see manufacturersinstructions on the packaging.The graduated detergentdispenser 9"helps you add thecorrect amount of powder or liquiddetergent.Usually 20 ml25 ml are adequatefor normal soiling. If using tablets,one tablet is adequate.

2. Close the cover on the detergentdispenser by sliding it up until thelock engages without difficulty.

The detergent dispenser opensautomatically at the optimum timedepending on the programme.The powder or liquid detergentis distributed in the appliance and isdissolved, the tablet falls into

the tablet collecting tray where itdissolves in doses.

Tip

If the utensils are only lightly soiled,slightly less than the indicated amountof detergent is usually adequate.

Suitable detergents and care products

can be purchased onlinevia our website or via customer service(see back page).

Combination detergent

Apart from conventional detergents(Solo), a number of products are offeredwith additional functions. Theseproducts contain not only the detergentbut also rinse-aid and salt replacementsubstances (3in1) and, dependingon the combination (4in1, 5in1, etc.),additional components such as glassprotection or stainless steel cleaner.Combination detergents function onlyup to a specific degree of hardness(usually 21dH). Over this limit saltand rinse-aid must be added.

As soon as combined detergents

are used, the rinse programmeis adjusted automatically to ensurethe best possible rinsing and dryingresult.

m Warning Do notplace small partsfor washing in the tablet collecting tray12; this prevents the tablet fromdissolving evenly.

m Warning If you want to add moreutensils after the programmehas started, do notuse the tabletcollecting tray 12as a handlefor the upper basket. The tablet couldalready be there and you will touchthe partially dissolved tablet.


18/40

en Detergent

18

Notes

You will obtain optimum rinsingand drying results by using solodetergents and applying saltand rinse aid separately.

If programmes are short, tabletsmay not have full cleaning effectdue to different dissolving propertiesand there may even be undissolveddetergent residue. It isrecommended to use washingpowder for these programmes.

The Intensive programme (on somemodels) requires one tab only. Whenusing washing powder, you canapply some of this cleaning agent

to the inside of the appliances door.

Even if the rinse-aid and/or salt refillindicator is lit, the rinse programmewill run correctly with combineddetergents.

If using detergents in a water-solubleprotective cover: Take hold of thecover with dry hands only and putthe detergent into an absolutelydry detergent dispenser only,otherwise the detergent may stick.

If you switch from combineddetergents to solo detergents,ensure that the water softeningsystem and amount of rinse aid havebeen set to the correct value.


19/40

Overview of programmes en

19

/Overview of programmesOverviewofprogrammes

The max. possible number of programmes is illustrated in this overview.The corresponding programmes and their arrangement can be found on the

fascia.

Type of utensils Type of soiling Programme Possibleadditionaloptions

Programme sequence

pots and pans,

non-sensitiveutensilsand cutlery

very adhesive burned-

in or dried-on foodremnants containingstarch or protein

/Intensive 70

all

Prerinse

Clean 70

Intermediate rinse

Final rinse 65

Drying

/Normal 65

all

Prerinse

Clean 65

Intermediate rinse

Final rinse 65

Drying

mixed utensilsand cutlery

part dried, commonhousehold foodremnants

/Normal 65

all

Prerinse

Clean 65

Intermediate rinse

Final rinse 65

Drying

/Eco 50

all

Prerinse

Clean 50

Intermediate rinse

Final rinse 65

Drying

sensitive utensils,cutlery,temperature-sensitive plasticand glasses

slightly adhesive,fresh food remnants

/Gentle 40

IntensivZone

Express Wash/Speed Perfect(VarioSpeed)

Half load

Extra drying

PrerinseClean 40

Intermediate rinse

Final rinse 55

Drying

/Quick 45

Extra drying

Clean 45

Intermediate rinse

Final rinse 55

all typesof utensils

cold rinsing,intermediate cleaning /

Prerinsenone Prerinse


20/40

en Additional options

20

Programme selection

You can select a suitable programmeaccording to the type of utensils anddegree of soiling.

Information for test institutes

Test institutes receive the information forcomparability tests (e.g. according toEN60436).

These are the conditions for conductingthe tests, however these are not theresults or consumption values.

Request by e-mail to:[email protected]

The product number (E no.) and theproduction number (FD) are requiredwhich you can find on the rating plate92on the appliance door.

0Additional optionsAdditional options* depending on model

Additional options can be set withthe buttons8.

Expr essW ash/ SpeedPer f ect ( Vari oSpeed)Express Wash/ SpeedPerfect/ (VarioSpeed) *

This function can reduce the runningtime by approx. 20% to 50% dependingon the selected rinse programme. Toobtain optimum cleaning and dryingresults at a reduced running time, waterand energy consumption are increased.

Intensive zone *Int ensivezone

Perfect for a mixed load. You can washvery soiled pots and pans in the lowerbasket together with normally soiled

utensils in the upper basket. The spraypressure in the lower basket isintensified, the rinsing temperature isincreased slightly.

Hygiene *Hygi ene

The temperature is increased during thecleaning process. This increases thehygiene status. This additional option is

ideal for cleaning e.g. chopping boardsand baby bottles.

Hal f loadHalf load *

If you have only a few items to wash(e.g. glasses, cups, plates), you canswitch to half load. This will savewater, energy and time. It is

recommended to put a little lessdetergent in the detergent dispenserthan for a full load.

Extra drying *Extr a dryi ng

An increased temperature during thefinal rinse and an extended dryingphase ensure that even plastic parts drybetter. There is a slight increase in the

energy consumption.


21/40

Operating the appliance en

21

1Operatingthe appliance

Operating theappliance

Programme dataThe programme data (consumptionvalues) can be found in the summaryof instructions. This data refers tonormal conditions and the waterhardness set value 2. Differentinfluencing factors such as watertemperature or mains pressure mayresult in deviations.

AquasensorAqua sensor *


The Aqua sensor is an opticalmeasuring device (light barrier) whichmeasures the turbidity of the rinsingwater.

The Aqua sensor is used according to

the programme. If the Aqua sensor isactive, clean rinsing water can betransferred to the next rinse bath andwater consumption can be reduced by36 litres. If the turbidity is greater, thewater is drained and is replaced withfresh water. In the automaticprogrammes the temperature andrunning time can also be adjusted to thedegree of soiling.

Switching on the appliance

1. Turn on the tap fully.

2. Open the door.

3. Switch on ON/OFF switch(.

The Eco 50 programme displayflashes. This programme remainsselected unless another programmeis selected with the button P.

4. Press the START buttonh.

5. Close the door.

The programme starts running.

Note

- for environmentally friendly operationof the dishwasher:For ecological reasons the Eco 50programme is preset whenever theappliance starts. This conservesenvironmental resources and not leastsaves you money.The Eco 50 programme is aparticularly environmentally friendlyprogramme. According to EU

regulation 1016/2010 it is theStandard programme which is themost efficient standard cleaning cyclefor cleaning normally soiled utensils interms of the combined energy andwater consumption for cleaning thesetypes of utensils.

Opt ical di splaywhi l et hepr ogr am m ei sr unni ngOptical display while

the programme is running ** depending on model

While the programme is running, a lightspot shines on the floor underthe appliance door. Do not openthe dishwasher door until the light pointis no longer visible on the floor.

If the appliance is installed at eye-level,with flush furniture front, the light point

is not visible.


22/40

en Operating the appliance

22

Tim er pr ogr am m ingTimer programming *


You can delay the start of theprogramme by 3, 6 or 9 hours.

1. Switch on ON/OFF switch(.2. Keep pressing the Preselected

starting time button0until theappropriate display 3h, 6h or 9h is lit.

3. Press START buttonh, timerprogramming is activated.

4. To delete the preselected startingtime, keep pressing the Preselectedstarting time button0until none ofthe displays 3h, 6h or 9h is lit.

You can change your programmeselection at any time until theprogramme starts.

End of programme

The programme has ended whenneither of the two displays`orXis lit.

The end of the programme is alsoindicated by an acoustic signal.The buzzer volume can be set in 4stages. Accordingly 0, 1, 2 or 3 displaysare lit (see water hardness table).Factory setting: 2. This function can bechanged as follows:

1. Open the door.


3. Hold down button > Pand pressSTART buttonhuntil the drydisplay`and salt refill

indicator )*flash.4. Release buttons.

5. Keep pressing button > Puntilthe salt refill indicator )*andrinseaid refill indicator )"flash.

6. Release buttons.

The refill indicators )*and )"flash and the displays#and+are lit (= Setting 2). The set buzzervolume can be heard.


1. Press the button


23/40

Operating the appliance en

23

Interrupting the programme

1. Open the door.

2. Switch off ON/OFF switch(.

The LEDs go out. The programme is

saved.If the door was opened on anappliance which has a warm waterconnection or is heated, first leavethe door ajar for several minutes andthen close. Otherwise, expansion(pressure) may cause the appliancedoor to spring open or water to runout of the appliance.

3. To continue the programme, switch

on the ON/OFF switch(again.4. Close the door.

Term inat i ngt hepr ogr am m eTerminating the programme(Reset)

1. Open the door.

2. Press START buttonhforapprox. 3 sec. until all displays go

out.3. Close the door.

The remaining programme sequencefor draining the residual water takesapprox. 1 minute.

Changing the programme

When the START button hhas beenpressed, the programme cannot bechanged.

The only way a programme can bechanged is by Cancel programme(Reset).

Intensive drying

The final rinse uses a highertemperature which improves the dryingresult. The running time may increaseslightly. (Caution if utensils are delicate!)

1. Open the door.


3. Hold down button > Pand pressSTART buttonhuntil the drydisplay`and salt refillindicator )*flash.

4. Release buttons.

5. Keep pressing button > Puntilthe salt refill indicator )*and

Check water supply )2flash.6. Release buttons.

The displays )*and )2flash.


1. Press button < Huntilthe display#is lit (Intensive dryingon).

2. Press START buttonh.

The displays go out. The setting

is saved.3. Close the door.


24/40

en Cleaning and maintenance

24

2Cleaning andmaintenance

Cleaning and maintenance

A regular inspection and maintenance

of your machine will help to preventfaults. This saves time and preventsproblems.

Overall conditionof the machine

Check spray arm for greaseand limescale deposits.

If you find such deposits: Fill detergent dispenser with

detergent. Start the appliance withoututensils in the programme withthe highest rinsing temperature.

Clean the appliance with detergents/appliance cleaners whichare particularly suitable for use withdishwashers.

To ensure that the door seal alwaysremains clean and hygienic, regularlyclean it with a damp cloth and a littlewashing-up liquid.

If the appliance is switched off fora prolonged period, leave the doorajar to prevent the formation ofan unpleasant odour.

Never use a steam cleaner to clean yourdishwasher. The manufacturer is notliable for any consequential damage.

Regularly wipe the front of the applianceand fascia with a damp cloth; water

and a little washing up liquidare adequate. Do not use sponges witha rough surface or abrasive detergents,as these could scratch the surfaces.

Stainless steel appliances: To preventcorrosion, avoid using sponge clothsor wash them out thoroughly severaltimes before using for the first time.

m Warning Health hazard

Never use other domestic detergents,e.g. containing chlorine!

Special salt and rinse aid

Check the refill indicators )*and)". If required, refill salt and/orrinse aid.


25/40

Cleaning and maintenance en

25

Filters

The filters 1Rkeep large foreignobjects in the rinsing water away fromthe pump. These foreign objects may

occasionally block the filters.The filter system consists of a coarsefilter, a flat fine filter and a microfilter.

1. After each washing cycle check thefilters for residue.

2. Unscrew filter cylinder as illustratedand take out filter system.

3. Remove any residue and clean filtersunder running water.

4. Re-install filter system in reversesequence and ensure that the arrowmarks are opposite each other afterclosing the filter system.

Spray arms

Limescale and contaminants in therinsing water may block nozzles andbearings on the spray arms 1:and

1B.1. Check outlet nozzles on the sprayarms for blockages.

2. Unscrew the upper spray arm 1:.

3. Remove the lower spray arm 1Bupwards.

4. Clean spray arms under runningwater.

5. Re-engage or screw on spray arms.


26/40

en Fault, what to do?

26

3Fault, what to do?Fault, what to do?

Experience has shown that you canrectify most faults which occur in daily

operation yourself. This ensures thatthe machine is quickly available to youagain. In the following overview you canfind possible causes of malfunctionsand helpful information for rectifyingthem.

Note

If the appliance stops duringdishwashing or does not start for noobvious reason, first run the Abortprogramme function (Reset).(See chapter entitled Operatingthe appliance)

m Warning Dont forget: Repairs maybe carried out by technicians only. If acomponent has to be replaced, ensurethat only original spare parts are used.Improper repairs or use of non-originalspare parts may cause considerable

damage and put the user atconsiderable risk.

Waste water pump

Large food remnants or foreign objectswhich were not captured by the filtersmay block the waste water pump. Therinsing water will then be abovethe filter.

m Warning Risk of cuts!When cleaning the waste water pump,ensure that you do not injure yourselfon pieces of broken glass or pointedimplements.

In this case:

1. First always disconnectthe appliance from the power supply.

2. Take out top basket 1"and bottombasket 1b.

3. Remove the filters 1R.4. Scoop out water, use a sponge if

required.

5. Prise out the white pump cover(as illustrated) using a spoon. Gripthe cover on the crosspiece and liftdiagonally inwards. Remove covercompletely.

6. Check impeller wheel and removeany foreign objects.

7. Place cover in the original positionand press down until it engages(click).

8. Install filters.

9. Re-insert baskets.


27/40

Fault, what to do? en

27

Fault table

Fault Cause Remedial action

Check water supplydisplay)2lights up.

Supply hose kinked. Install supply hose without kinks.

Tap turned off. Turn the tap on.Tap jammed or calcified. Turn the tap on.

Flow rate must be min. 10 l/min. whenwater supply is open.

Filter in the water supply blocked. Switch off the appliance and pull out themains plug. Turn off the tap. Unscrew waterconnection.

Clean filter in the supply hose. Screw waterconnection on again. Check for leaks.Reconnect power supply. Switch on theappliance.

Filters1Rare soiled orblocked.

Clean filters.

(see Cleaning and maintenance).

Waste-water hose kinked orblocked.

Install hose without kinks, remove anyresidue.

Siphon connection still sealed. Check connection to siphon and open ifrequired.

Waste water pump blocked orcover on the waste water pump is

not locked in position.

Lock cover correctly.

(See Waste water pump)

Display Check watersupply)2flashes.

A technical fault has probablyoccurred.

Switch off appliances with the ON/OFFswitch(. After a short time restart theappliance.

If the problem recurs, turn off the tap, pullout the mains plug and call customerservice.

Refill indicator for salt)*flashes.

Heating element calcified orsoiled.

Clean appliance with dishwasher cleaningagent or descaler. Operate the dishwasherwith water softening system and check the

setting (see chapter Water softeningsystem/Special salt).


28/40


28

Displays flash. Door not closed properly. Close the door. Ensure that no objects(utensil, fragrance dispenser) are protrudingover the basket and preventing the doorfrom closing.

Refill indicator for salt)*and/or rinse-aid)"is lit.

No rinse aid. Refill rinse aid.

No salt. Refill with special salt.

Sensor does not detect salttablets.

Use different special salt.

Refill indicator for salt)*and/or rinse-aid)"is notlit.

Refill indicator switched off. Activation/deactivation (see chapter Watersoftening system/Special salt or Rinse aid).

There is still enough special salt/rinse aid available.

Check refill indicator, levels.

Water is left in theappliance at the end of theprogramme.

Filter system or area under thefilters1Ris blocked. Clean filters and area underneath (seeWaste water pump).

Program has not ended yet. Wait until programme ends or reset (seeTerminating the programme).

Utensils not dry. No or too little rinse aid in thedispenser.

Refill rinse aid.

Programme selected withoutdrying.

Select programme with drying (seeOverview of programmes, Programmesequence).

Water collecting in depressionson the utensils and cutlery. Arrange utensils in a sloping position,arrange affected utensils as sloping aspossible.

The combined detergent used

has a poor drying performance

Use different combination detergent with

better drying performance. Use of rinse aidalso increases the drying performance.

Intensive drying to increasedrying not activated.

Activate intensive drying (see Operating theappliance)

Utensils were removed too earlyor drying process had not endedyet.

Wait until program ends or wait until 30 minafter program ends before removingutensils.

The eco rinse aid used has a poordrying performance.

Use a proprietary rinse aid. Eco products aremuch less effective.

Plastic utensils not dry. Special properties of plastic. Plastic has a lower heat storage capacityand therefore dries less well.



29/40


29

Cutlery not dry. Cutlery not arranged properly inthe cutlery basket.

Separate cutlery if possible, prevent contactpoints.

Cutlery not arranged properly inthe cutlery drawer.

Arrange cutlery properly and separate ifpossible.

Appliance interior wet afterrinse cycle.

No appliance fault On account of the Condensation dryingprinciple, water droplets are physicallyinduced and required in the container. Thehumidity in the air condenses on the innerwalls of the dishwasher, drains and ispumped out.

Food remnants on theutensils.

Utensils placed too closelytogether, utensils basketoverfilled.

Arrange utensils with adequate clearancebetween them ensuring that the spray jetscan reach the surface of the utensils.

Prevent contact points.Spray arm rotation obstructed. Arrange utensils so that the spray arm can

rotate without obstruction.

Spray arm nozzles are blocked. Clean the spray arm nozzles.

(see Cleaning and maintenance).

Filters1Rdirty. Clean filters (see Cleaning andmaintenance).

Filters1Rinserted incorrectlyand/or not engaged.

Insert and engage filters correctly.

Rinse programme too weak. Select a more intensive rinse programme.

Utensils precleaned too intensely;sensors therefore decide onweak programme sequence.Stubborn soiling cannot becompletely removed.

Do not prerinse utensils. Remove only largefood remnants.

Recommended programme Eco 50 orIntensive.

Tall narrow receptacles in cornerareas are not rinsed adequately.

Do not place hollow receptacles tooobliquely and do not place in the cornerarea.

Top basket1"on right and leftnot set to same height.Set top basket to same height using sidelevers.



30/40


30

Detergent residue. Detergent dispenser coverblocked by utensils and thereforedoes not open fully.

Detergent dispenser cover must not beobstructed by utensils.

Do not place utensils or fragrance dispenserin the tablet collecting tray.

Detergent dispenser coverblocked by the tablet.

Tablet must be inserted flat and not upright.

Tablets used in the quick or shortprogramme.

Dissolving time of the detergentis not reached in the selectedshort programme.

Dissolving time of tablets too long for aquick or short programme.

Use a detergent powder or select a moreintensive programme.

Washing effect and dissolvingperformance are reduced after aprolonged storage time ordetergent is very lumpy.

Change detergent.

Water stains on plasticparts.

Droplet formation on plasticsurface is physically unavoidable.After drying, water stains arevisible.

Use a more intensive programme (morewater changes).

Arrange utensils in a sloping position.

Use rinse aid.

If required, increase softening setting.

Washable or water-solublecoatings in the container oron the door.

Detergent substances aredeposited. These coatings cannotusually be removed withchemicals (appliance cleaner, ...).

Change detergent brand.

Clean appliance mechanically.

If there is a white coating on thecontainer floor, the watersoftening system has been setmarginally.

Increase softening setting and changedetergent if required.

Salt dispenser cover1Jnotclosed.

Close salt dispenser cover correctly.

Only for glasses: Initial glass

corrosion can only apparentlybe wiped off.

See Glass and utensil damage.



31/40


31

White, stubborn coatings;limescale on the utensils,container or door.

Detergent substances aredeposited. These coatings cannotusually be removed withchemicals (appliance cleaner, ...).

Change detergent brand.

Clean appliance mechanically.

Hardness range incorrectly set orwater hardness greater than 8.9mmol/l.

Set water softening system according toinstructions for use or top up salt.

3 in 1 detergent or bio/ecodetergent not effective enough.

Set water softening system according toinstructions for use or use separatedetergents (proprietary detergent, salt, rinseaid).

Underdosing of detergent. Increase detergent dosage or changedetergent.

Too weak rinse programmeselected.

Select a more intensive rinse programme.

Tea or lipstick residue onthe utensils.

Too low rinsing temperature. Select programme with higher washingtemperature.

Too little or unsuitable detergent. Use suitable detergent at correct dosage.

Utensils precleaned too intensely;sensors therefore decide onweak programme sequence.Stubborn soiling cannot be

completely removed.


Recommended programme Eco 50

Coloured (blue, yellow,brown), difficult to removeto non-removable coatingsin the appliance or onstainless steel utensils.

Film formation consisting ofingredients from vegetables (e.g.cabbage, celery, potatoes,noodles, ...) or the tap water (e.g.manganese).

Can be partly removed with machinecleaner or by mechanical cleaning. Coatingsare harmless.

Film formation caused by metalliccomponents on silver oraluminium utensils.

Can be partly removed with machinecleaner or by mechanical cleaning.

Coloured (yellow, orange,

brown), easily removabledeposits inside theappliance (mainly in thefloor area)

Film formation consisting of

ingredients from food remnantsand substances from the tapwater (limescale), soapy

Check function of the water softening

system (refill with salt) or, if using combineddetergents (tablets), activate watersoftening system (see chapter Watersoftening system/Special salt)

Plastic parts discoloured. Too low rinsing temperature. Select programme with higher washingtemperature.






32/40


32

Removable streaks onglasses, glasses withmetallic appearance andcutlery.

Too much rinse aid. Set rinse aid amount to lower setting.

No rinse aid added or setting toolow.

Add rinse aid and check dosage(recommended setting 45).

Detergent residue in the finalrinse programme section.Detergent dispenser coverblocked by utensils (cover doesnot open fully).

Detergent dispenser cover must not beobstructed by utensils.

Do not place utensils or fragrance dispenserin the tablet collecting tray.




Initial or existing,irreversible clouding ofglass.

Glasses not dishwasher-proof,only suitable for dishwasher.

Use dishwasher-proof glasses.Avoid long steam phase (standing time afterwash cycle ends).

Use wash cycle at lower temperature.

Set water softening system according to thewater hardness (if required one settinglower).

Use detergent with glass protectioncomponent.

Rust spots on the cutlery. Cutlery not adequately rust-resistant. Knife blades arefrequently more severelyaffected.

Use corrosion-resistant cutlery.

Cutlery will also rust if rustingparts are rinsed at the same time(pan handles, damaged utensilbaskets, etc.).

Do not wash rusting parts.

Salt content in the rinsing watertoo high, as salt dispenser locknot fastened firmly or salt wasspilled while being refilled.

Fasten salt dispenser lock firmly or removespilled salt.

Appliance does not start. The mains fuse has tripped. Check mains fuse.

Power cord not inserted. Ensure that the power cord is plugged allthe way into the back of the appliance andinto the socket. Check that the socketfunctions.

The appliance door has not beenshut properly.

Close the door.

Programme startsautomatically.

You did not wait until programmeended.

Perform reset.

(See Terminating the programme).



33/40


33

The door is difficult toopen.

Child lock is activated. Deactivate child lock. (See instructions foruse at the back)

Door cannot be closed. Door lock has been activated. Close door with increased force.

Door cannot be closed due toinstallation.

Check appliance installation: Dooror attached parts must close withoutobstruction.

Cover on the detergentdispenser cannot beclosed.

Detergent dispenser or coverguide blocked by sticky detergentresidue.

Remove detergent residue.

Detergent residue in thedetergent dispenser or inthe tablet collecting tray.

Spray arms blocked by utensils,therefore detergent is not rinsedout.

Ensure that the spray arms can rotate freely.

The detergent dispenser wasdamp when filled.

Pour detergent into the dry detergentdispenser only.

Appliance stops in theprogramme or programmeis interrupted.

Door not closed properly. Close the door.

Do not place utensils or fragrancedispenser in the tablet collectingtray.

Top basket presses against thedoor and prevents door frombeing closed securely.

Check whether rear panel is being pressedin, e.g. by socket or by hose holder whichhas not been removed.

Power and/or water supply

interrupted.

Restore power and/or water supply.

Filling valves makingstriking noises.

Depends on domestic installation,as appliance is not defective. Noeffect on appliance function.

No remedial action possible.

Knocking or rattling noise. Spray arm strikes the utensils,utensils not positioned correctly.

Position utensils so that the spray arms donot strike the utensils.

If there is a low load, the waterjets strike the washing tankdirectly.

Load the appliance with more utensils ordistribute the utensils more evenly in thedishwasher.

Light utensils move during thewash cycle.

Arrange light utensils securely.

Unusual foam formation. Handwash liquid in the rinse aiddispenser.

Immediately refill rinse aid dispenser withrinse aid.

Rinse aid spilled. Remove rinse aid with a cloth.



34/40

en Customer service

34

4Customer serviceCustomer service

If you are unable to rectify the fault,please contact your customer service.

We always find a suitable solution, evento avoid unnecessary visitsby technicians. Contact informationfor your nearest customer service canbe found on the back of theseinstructions for use or on the enclosedcustomer service list. When calling,please state the appliance number (E-Nr. = 1) and the production number(FD = 2) which can be found on therating plate 92on the appliance door.

Rely on the competence of the manufacturer.Contact us. You can therefore be

sure that the repair is carried outby trained service technicians who carryoriginal spare parts for your domesticappliances.


5Installation andconnection

Installation and connection

The dishwasher must be connected

correctly, otherwise it will not functionproperly. The specifications for the inletand outlet as well as the electricalconnected loads must correspond withthe required criteria asspecified in the following paragraphsor in the installation instructions.

Install the appliance in the correctsequence:

1. Checking appliance on delivery

2. Installing the appliance

3. Waste water connection

4. Drinking water connection

5. Electrical connection


35/40

Installation and connection en

35

Product package

If you have any complaints, contactthe dealer where you purchasedthe appliance or our customer service.

Dishwasher Instructions for use

Installation instructions

Warranty*

Installation materials

Steam guard plate*

Rubber apron*

Power cord


Safety instructions

Please follow the safety instructionsunder Installation.

Delivery

Your dishwasher has been checkedthoroughly in the factory to ensure that itis in working order. This may causesmall water stains. These will disappearafter the first wash cycle.

Technical specifications

Weight:

max. 60 kg

Voltage:

220240 V, 50 Hz or 60 Hz

Connected load:

2.02.4 kW

Fuse:

10/16 A (UK 13A)

Power input:

switched off 0.10 W

not switched off 0.10 W

Water pressure:

at least 0.05 MPa (0.5 bar), maximum1 MPa (10 bar). At a higher waterpressure: connect pressure-reducingvalve ahead.

Inlet rate:

minimum 10 litres/minute

Water temperature:

Preferably cold water; if hot water,depending on type of water inlet hose,max. temp. 60 C (see Drinking waterconnection).

Capacity:

1215 place settings(depending on model).


36/40

en Installation and connection

36

Installation

The required installation dimensions canbe found in the installation instructions.Level the appliance with the aid of the

height-adjustable feet. Ensure that theappliance is situated securely on thefloor.

A built-under or integrated appliancewhich is installed subsequently as afree-standing appliance must besecured to prevent it fromoverturning, e.g. by screwing it to thewall or by installing it undera continuous worktop which isscrewed to adjacent cupboards.

The appliance can easily beinstalled in a fitted kitchen betweenwooden and plastic walls.

Waste-water connection

1. The required work sequence can befound in the installation instructions.If required, fit a siphon with an

drainage connection.2. Connect the waste-water hose to the

drainage connection of the siphonwith the enclosed parts.

Ensure that the drainage hose is notkinked, crushed or twisted and thatthere is no cover plate in thedrainage to prevent the waste waterfrom flowing out!

Drinking water connection

1. Fasten the drinking water connectionto the tap accordingto the installation instructions using

the enclosed parts.Ensure that the drinking waterconnection is not kinked, crushedor twisted.

2. When replacing the appliance,always use a new water supply hose.

Water pressure:

At least 0.05 MPa (0.5 bar), maximum1 MPa (10 bar). At a higher waterpressure: connect pressure-reducing

valve ahead.

Inlet rate:

Minimum 10 litres/minute

Water temperature:

Note printing on the water inlet hose!

If models are marked with 25,the water temperature may be max.25 C (cold water).

For all other models:

Cold water preferred; hot water max.temperature 60 C.


37/40

Installation and connection en

37

Electrical connection

Connect the appliance to analternating current only, ranging from220 V to 240 V and 50 Hz or 60 Hz

via a correctly installed socket withprotective earth conductor. Seerating plate for required fusing 92.

The socket must be nearthe appliance and freely accessiblefollowing installation.

If the plug is not freely accessible, anallpole disconnector with a contactopening of at least 3 mm must befitted on the installation side

to satisfy the relevant safetyinstructions.

The connection may be modified bytechnicians only.

A power cord extension may bepurchased from customer serviceonly.

Use only a residual current operatedcircuit-breaker which featuresthe symbol. Only this extension

guarantees compliance withthe currently valid regulations.

The appliance features a waterdamage protection system. Pleasenote the system will not functionunlessthe power supplyis connected.

Removing the appliance

Also observethe sequence of worksteps here.

1. Disconnect the appliance from

the power supply.2. Turn off the water supply.

3. Undo the waste water and drinkingwater connection.

4. Loosen fastening screws forthe furniture parts.

5. If fitted, remove the base panel.

6. Pull out the appliance, carefullypulling the hose behind.


38/40

en Installation and connection

38

Transportation

Empty the dishwasher and secure looseparts.

Drain the appliance according

to the following steps:1. Turn on the tap.

2. Open the door.


4. Select programme@withthe highest temperature button

Dishwasher Sn64e005eu instruction for use.pdf

Documents

Transcript of Dishwasher Sn64e005eu instruction for use.pdf