Disassemble N011
Transcript of Disassemble N011
U100(MS-N011)Disassemble SOP
■ 1、Battery Pack
■ 2、LOWER CASE ASSY
■ 3、WLAN and RAM Module
■ 4、HDD Module ASSY
■ 5、THERMAL-KIT And CPU Module
■ 6、Disassemble LCD and UPCASE
■ 7、UP CASE ASSY
■ 8、LCD MODULE ASSY
U100(MS-N011)Disassemble SOP
■ 1、Battery Pack
1-1:Push the battery Unlock button in the direction shown below;
1-2:Push the battery Release button in the direction shown below, then slide the battery pack out of the slot;
NO. Part Name Part No. Qty
1 Battery Pack S9N-1832300-SJ3 1
U100(MS-N011)Disassemble SOP ■ 2、LOW CASE ASSY
2-1:Remove 9pcs M2*2.5mm screws which is on Bottom Door with Screw Driver.
Note:driver torque is 1.8-2.2Kgf-cm(3-9) Note:Screw driver torque is 3.0-3.5Kgf-cm (1-2)
7
5
8 9
6
4
2
3
1
2-2:Remove Bottom Door Assy;
NO. Part Name Part No. Qty
1 Screw E43-1255007-H29 9
2 LOW CASE ASSY 307-011D411-TA2 1
U100(MS-N011)Disassemble SOP ■ 3、WLAN and RAM Module
3-1: Remove 1pcs M2*3mm screw ,Then Remove ANTENNA/HIGH-TEK/R-L in the direction shown below;
Note:Screw driver torque is 1.0-1.4Kgf-cm
1
3-2:Remove WIRELESS CARD in the direction shown below;
NO. Part Name Part No. Qty
1 WIRELESS CARD 605-6894-A10 1
2 Screw E43-1203003-H29 1
U100(MS-N011)Disassemble SOP
3-3:Push the RAM locks away;
3-4:Take off the RAM Module as below;
NO. Part Name Part No. Qty
1 RAM Module S7C-S347701-T10 1
U100(MS-N011)Disassemble SOP
■ 4、HDD Module ASSY 4-1:Remove 1pcs M2*2.5mm screw, Then RemoveHDD Module Assy in the direction shown below;
Note:Screw driver torque is 1.8-2.2Kgf-cm
1
NO. Part Name Part No. Qty
1 screw E43-1255007-H29 1
U100(MS-N011)Disassemble SOP
4-2:Remove 2pcs M3*3.5mm screws ,Then Remove HDD Bracket in the direction shown below;
Note:Screw driver torque is 1.8-2.2Kgf-cm
2
1
NO. Part Name Part No. Qty
1 Screw E43-1303502-H29 2
2 HDD Bracket Assy 307-0110111-A89 1
3 HDD MODULE ASSY S71-2408505-W36 1
U100(MS-N011)Disassemble SOP
■ 5、THERMAL-KIT And CPU Module 5-1:Remove 1pcs M2*2.5 screw, CPU Fan sink Cable and Remove HEATSINK in order.
Note:Screw driver torque is 1.8-2.2Kgf-cm
1
NO. Part Name Part No. Qty
1 screw E43-1255007-H29 1
2 CPU FAN MOUDULE OE3-0800020 1
HEATSINK E31-0800720-TA9 1
U100(MS-N011)Disassemble SOP
■ 6、Disassemble LCD and UPCASE 6-1: Remove LCD LVDS Cable 、CMOS CABLE、 BLUETOOTH CABLE、 MICROPHONE Cable、
Then Remove SPEAKER MODULE Cable in the direction shown below;
U100(MS-N011)Disassemble SOP
6-2:Remove LCD LVDS Cable 、CMOS CABLE、 BLUETOOTH CABLE、 MICROPHONE Cable、
Then Remove SPEAKER MODULE Cable in the direction shown below;
NO. Part Name Part No. Qty
1 CMOS CABLE K10-3006060-H39 1
2 COAXIAL CABLE K19-3024001-V03 1
3 BLUETOOTH CABLE K10-3008069-H39 1
U100(MS-N011)Disassemble SOP
6-3:Remove 4pcs M2*2.5mm screws which is use screw driver;
Note:Screw driver torque is 3.0-3.5Kgf-cm
21
NO. Part Name Part No. Qty
1 screw E43-1255007-H29 2
U100(MS-N011)Disassemble SOP
6-4:Remove LCD MODULE ASSY in the direction shown below;
U100(MS-N011)Disassemble SOP
■ 7、UP CASE ASSY
7-1:Remove 1pcs M2*3mm Screw, Remove FFC Cable (TO Button) in the direction shown below;
Note:Screw driver torque is 1.0-1.4Kgf-cm
1
7-2:Remove M/B ,Then Remove DIS BATTERY in the direction shown below;
NO. Part Name Part No. Qty
1 Screws E43-1203003-H29 1
2 DIS BATTERY D06-0100300-H04 1
U100(MS-N011)Disassemble SOP
7-3:Remove Keyboard in the direction shown below;
7-4:Remove Keyboard Cable in the direction shown below;
NO. Part Name Part No. Qty
1 Keyboard S1N-1UUS361-SA0 1
U100(MS-N011)Disassemble SOP
7-5:Remove Touchpad FFC (To Button),Remove Touchpad Module in the direction shown below;
NO. Part Name Part No. Qty
1 Touchpad Module S78-3700170-SD2 1
2 Touchpad FFC (To Button) K1C-1012026-J36 1
U100(MS-N011)Disassemble SOP
7-6:Remove Bluetooth Antenna ,Then Remove BLUETOOTH CABLE in the direction shown below;
7-7:Remove BLUETOOTH MODULE in the direction shown below;
NO. Part Name Part No. Qty
1 BLUETOOTH MODULE 605-6837D-050 1
2 BLUETOOTH CABLE K10-3008069-H39 1
U100(MS-N011)Disassemble SOP
7-8:Remove speaker in the direction shown below;
NO. Part Name Part No. Qty
1 Speaker S33-A010300-F33 1
U100(MS-N011)Disassemble SOP
7-9:Remove MAGNET in the direction shown below;
NO. Part Name Part No. Qty
1 MAGNET E2M-0110611-SF7 2
2 M/B 607-N0111-C10 1
3 UP CASE ASSY 307-011C411-TA2 1
U100(MS-N011)Disassemble SOP
■ 8、LCD MODULE ASSY 8-1:Remove 4pcs LCD Rubbers ,Then Remove 4pcs M2*2.5mm screws in the direction shown below;
Note:Screw driver torque is 2.0~.2.2kgf*cm
4
2
3
1
4 3
2 1
NO. Part Name Part No. Qty
1 Screw E43-1255007-H29 4
2 LCD SECOND RUBBER E2Y-0112711-Y40 2
3 LCD RUBBER E2Y-0112611-Y40 4
U100(MS-N011)Disassemble SOP
8-2:Remove LCD Bezel in the direction shown below;
NO. Part Name Part No. Qty
1 LCD BEZEL 307-011B411-TA2 1
U100(MS-N011)Disassemble SOP
8-3:Remove 2pcs M2*2.5mm screws , Then Remove Hinge LCD_HINGE_CAP;
Note:Screw driver torque is 3.0~.3.2kgf*cm
1 2
1 2
8-4:Remove Hinge Cap-L-R in the direction shown below;
1 2
NO. Part Name Part No. Qty
1 Hinge_Left E2M-0110211-G60 1
2 Hinge_Right E2M-0110111-G60 1
3 LCD_HINGE_CAP E2P-0110111-TA2 2
4 Screw E43-1255007-H29 2
U100(MS-N011)Disassemble SOP
8-5:Remove 2pcs M2*3mm screws, Then Remove 2pcs magnet in the direction shown below;;
Note:Screw driver torque is 2.5~.2.8kgf*cm
1
2
NO. Part Name Part No. Qty
1 Screw E43-1203003-H29 2
2 MAGNET E2M-0110811-SF7 2
U100(MS-N011)Disassemble SOP
8-6:Remove Display Module in the direction shown below;
U100(MS-N011)Disassemble SOP
8-7:Remove CMOS CABLE,Remove CMOS Camera Module in the direction shown below;
NO. Part Name Part No. Qty
1 CMOS Camera Module S1F-0001200-AF5 1
U100(MS-N011)Disassemble SOP
8-8:Remove2PCS WIRELESS ANTENNA in the direction shown below;
NO. Part Name Part No. Qty
1 WIRELESS ANTENNA_R S79-1800990-V03 1
2 WIRELESS ANTENNA_L S79-1800980-V03 1
U100(MS-N011)Disassemble SOP
8-9:Remove MICROPHONE in the direction shown below;
NO. Part Name Part No. Qty
1 MICROPHONE S34-2100680-F33 1
2 LCD Cover Assy 307-011A411-TA2 1
U100(MS-N011)Disassemble SOP
8-10:Remove Coaxial Cable in the direction shown below;
NO. Part Name Part No. Qty
1 LCD LVDS Cable K19-3024001-V03 1
2 ANTI-GLARE OS1-N011001 1
U100(MS-N011)Disassemble SOP
8-11:Remove 4pcs M2*3mm Screws, Then Remove LCD Bracket in the direction shown below;
Note:Screw driver torque is 1.5~.1.8kgf*cm
2 4
3 1
2 1
NO. Part Name Part No. Qty
1 Screw E43-1203003-H29 4
2 DISPLAY MODULE S1J-100A002-H34 1
3 LCD-Bracket E2M-0110311-A89 2
(MS-N011)screws specification
Photo Screw specification label
(M2*3mm)white
(M2*2.5 mm) black
(MS-N011)screws specification
■ 1、LOW CASE ASSY 9pcs screws,
specification:
Photo Screw specification Label
(M2*2.5 mm) black
(MS-N011)screws specification
■ 2、 wireless 1pcs screw,
specification:
Photo Screw specification Label
(M2*3mm)white
(MS-N011)screws specification
■ 3、HDD、NB 5pcs screws,
specification:
1
Photo Screw specification Label
(M2*2.5 mm) black
(M2*3mm)white
(MS-N011)screws specification
■ 4、 LCD Bezel total 4pcs screws,
specification:
Photo Screw specification Label
(M2*2.5 mm) black
(MS-N011)screws specification
■ 5. LCD Bracket total 8pcs screws,specification:
Photo Screw specification Label
(M2*2.5 mm) black
(M2*3mm)white