2

Dippity Duo Tea Cozy Cover 13” x 10”

Before Getting Started:

Read all instructions before beginning this project to find valuable tips, save time and

minimize mistakes by understanding the process before you begin!

Truly McKenna Art Prints are not pre-shrunk. If you are making a project that will be

washed after use, you may want to pre-wash your fabrics.

The term WOF refers to width of fabric.

Use an accurate ¼” seam allowance unless instructed otherwise in pattern directions.

We strive to create accurate patterns, but just as no tree in nature is perfect, neither are we.

Visit our website at www.pineneedles.com for any corrections before beginning your quilt.

Material Needed:

• One IFB05-P Dippity Duo Truly McKenna Panel

• Fabric 1: MR10-70 Lavender - ½ yard for Lining and Backing

• Fabric 2: 885-106 Celery - ¼ yard for Binding

• ½ yard of Insul-Bright™

Preparing Panel and Fabric:

• Trim Dippity Duo Panel to 14” x 11”

• Fabric 1:

o Cut 3 - 11” x 14” rectangles for Lining and Backing

o Cut 1 - 6” x 14” strip for Pockets *Optional

o Cut 1 - 1½” x 4” strip for Hanging Loop *Optional

• Fabric 2: Cut 3 - 2½” x WOF strips for Binding

o Subcut 1 strip into 3 - 2½” x 14” strips

• Insul-Bright: Cut 2 - 14” x 11” rectangles

Tea Cozy Front:

1. Layer one of the 14” x 11” Lining pieces right side down, one 14” x 11” piece of Insul-Bright and the Dippity Duo panel right side up.

2. Quilt as desired.

3. Square edges and trim to 13” x 10”

4. Using one of the 14” binding strips, bind bottom edge of the Tea Cozy front.

Tea Cozy Back:

1. Layer one of the 14” x 11” Lining pieces right side down, the remaining 14” x 11” piece of Insul-Bright and the remaining 14” x 11” Lining piece right side up for the Backing.

2. Quilt as desired.

3. Square edges and trim to 13” x 10”

4. Pockets on back: *Optional

a. Iron the 6” x 14” Pocket strip in half to create a 3” x 14” strip.

b. Bind top edge with one of the 14” binding strips.

c. Line up the bottom and side raw edges of the Pocket with the

bottom and side raw edges of the Tea Cozy back and baste in place.

d. Section off Pocket into three equal sections and stitch to create

three little pockets.

5. Using the remaining 14” binding strip, bind bottom edge of the Tea Cozy

back.

3

Hanging Loop: *Optional

1. Fold the 1½” x 4” Fabric 1 piece in half, right sides facing and press. 2. Stitch along the 4” raw edge and turn right side out to create a “tube” and press. 3. Stitch along each edge for a decorative touch.

Assembly:

1. Layer the Tea Cozy front and back with right sides out.

2. Fold Hanging Loop in half and pin to the top center of the Tea Cozy front, lining up the top raw edge of the Tea

Cozy front with the raw edges of the Hanging Loop ends.

3. Baste the front and back pieces together, stitching very close to the edge. This will help keep them from shifting

while sewing binding on. The seam will be on the outside.

4. Cut a 2” triangle off the Right and Left top corners for a decorative look. *Optional

5. On the Tea Cozy front, sew the binding on, starting in one of the bottom corners.

6. Wrap binding around to back side and hand or machine stitch in place.

7. Fold Hanging Loop up and tack to binding.

Enjoy Tea Time with your special Tea Cozy!

The Insul-Bright helps keep the tea pot warm and doubles as a hot pad when flat!

©2018 McKenna Ryan LLC · All Rights Reserved · 1915 SE Jefferson Street, Portland, OR 97222

1.800.728.2278 · www.pineneedles.com · Distributed exclusively by Pine Needles Designs