DIGIDIM Infrared Remote Control (303) Installation and User Guide

2
1 www.helvar.com Helvar | Data is subject to change without notice. DIGIDIM Infrared Remote Control (303) Installation and User Guide A: LED Indicator (flashes as each message is transmitted) B: Scene Recall/Configuration C: Modifier Keys D: On/Off/Shift E: Transmitter F: Rotary address switch (default setting position ‘0’ – use a 1.5 mm tip slotted screwdriver to turn the switch.) G: Battery Cover Basic Functions Product Description The DIGIDIM Infrared Remote Control (303) can be used in conjunction with Helvar DIGIDIM products to switch the lights on and off, modify the preset light levels and recall and store scenes. Insert AAA batteries observing polarity as indicated on the interior of the battery compartment. Notes: The styling has been revised for 2016. Batteries are included. + A B C G E D F 0 4 C 5 6 7 1 2 3 F E D B A 9 8 4 O 5 6 7 1 2 3 100 % 50 % 75 % 25 % To recall a scene: 3.1 Point the remote control at the desired receiver. 3.2 Press the scene key 1, 2, 3 or 4, as applicable, to recall the required scene. Note: In this example, the scenes have been programmed as follows: scene 1: 100 %; scene 2: 75 %; scene 3: 50 %; scene 4: 25 %. Recall Scenes 4 O 5 6 7 1 2 3 0 % Switch Lights On/Off To switch the lights on or off: 2.1 Point the remote control at the desired receiver. 2.2 Press ‘0’ on the remote control to switch the lights on or off. O 5 6 7 1 2 3 + Install Preset Light Levels With the remote control, you can install four default preset light levels. To do this: 1.1 Point the remote control at the desired receiver. 1.2 Simultaneously press and hold remote control keys 3 and 4 until the receiver’s indicator LEDs flash to confirm that the preset light levels have been successfully loaded. Note: Throughout this document, ‘receiver’ refers to button panels and sensors that can be operated with the DIGIDIM Infrared Remote Control.

Transcript of DIGIDIM Infrared Remote Control (303) Installation and User Guide

Page 1: DIGIDIM Infrared Remote Control (303) Installation and User Guide

1www.helvar.com Helvar | Data is subject to change without notice.

DIGIDIM Infrared Remote Control (303)

Installation and User Guide

A: LED Indicator (flashes as each message is transmitted)B: Scene Recall/ConfigurationC: Modifier KeysD: On/Off/ShiftE: TransmitterF: Rotary address switch (default setting position ‘0’ – use

a 1.5 mm tip slotted screwdriver to turn the switch.)G: Battery Cover

Basic Functions

Product DescriptionThe DIGIDIM Infrared Remote Control (303) can be used in conjunction with Helvar DIGIDIM products to switch the lights on and off, modify the preset light levels and recall and store scenes.

Insert AAA batteries observing polarity as indicated on the interior of the battery compartment.Notes: The styling has been revised for 2016. Batteries are included.

+

+

AB

C G

E

D

F0

4C 567

123FEDB A98

4 O

5

6

7

1

2

3

100 % 50 %75 % 25 %To recall a scene:3.1 Point the remote control at the desired receiver.3.2 Press the scene key 1, 2, 3 or 4, as applicable, to recall

the required scene.Note: In this example, the scenes have been programmed as

follows: scene 1: 100 %; scene 2: 75 %; scene 3: 50 %; scene 4: 25 %.

Recall Scenes

4 O

5

6

7

1

2

3

0 %

Switch Lights On/OffTo switch the lights on or off:2.1 Point the remote control at the desired receiver.2.2 Press ‘0’ on the remote control to switch the lights on

or off.

O

5

6

7

1

2

3 +

Install Preset Light LevelsWith the remote control, you can install four default preset light levels. To do this:1.1 Point the remote control at the desired receiver.1.2 Simultaneously press and hold remote control keys 3

and 4 until the receiver’s indicator LEDs flash to confirm that the preset light levels have been successfully loaded.

Note: Throughout this document, ‘receiver’ refers to button panels and sensors that can be operated with the DIGIDIM Infrared Remote Control.

Page 2: DIGIDIM Infrared Remote Control (303) Installation and User Guide

2 Helvar 303 DIGIDIM Infrared Remote Control: User and Installation Guide Doc. 7860345, issue 1, 2015-12-12

Helvar Ltd Hawley Mill Hawley Road Dartford Kent DA2 7SY United Kingdom www.helvar.com

Store Scenes

10 s

4 O

5

6

7

1

2

3

10 s 10 s 10 s

To store a modified scene:5.1 Point the remote control at the desired receiver.5.2 Hold the scene key 1, 2, 3 or 4, as applicable, for 10

seconds to store the scene.The receiver’s indicator LEDs will flash if successful.

Technical Data

Batteries: 2 × IEC, LR03/AAA 1.5 V battery Note: Batteries are included.

Operating range: Approximately 5 mIR frequency: 36 kHz

Mechanical dataDimensions: 40 mm × 145 mm × 15 mmHousing: Black, nonflammable

polycarbonate, halogen freeWeight: 50 g

Operating conditionsAmbient temperature: 0 °C to +40 °CRelative humidity: Max. 90 %, noncondensingStorage temperature: –10 °C to +70 °C

Conformity and standardsEnvironment: Complies with WEEE and

RoHS directives.

Address SwitchThe remote has a rotary address switch in the battery compartment (figure 1, item F) that allows for multiple remotes and receivers to be used within one area without cross interference.If you set the switch to any address from 1 thru 9 or A thru E, the remote will only operate the receivers that are configured to accept infrared commands from that specific address. If you set the switch to ‘0’ (default), the remote will operate all the receivers within its operating range, irrespective of how their addresses are set. The ‘F’ address is reserved for future use.The address from which a receiver accepts infrared commands is set with Helvar’s Designer or Toolbox software.

Modify Light LevelsTo modify the current light levels:4.1 Point the remote control at the desired receiver.4.2 Adjust the lighting to the required level using the Up

and Down modifier keys.

4 O

5

6

7

1

2

3 1 %

1 %100 %

100 %