Design Collection

Sapa Pole ProductsDesign Collection

Introduction

Page 4 Sapa Pole Products

Page 6 Aluminium, the facts

Page 8 Aluminium, the green metal

Page 10 Strength calculations

Page 12 Crash friendly columns

Page 14 Surface treatment

Page 16 Accessories

Page 18 Collections of Sapa columns

Page 38 Brackets

Page 40 Worldwide projects

Content

By using aluminium, there is no need for you to paint your columns, which saves both time and money. Aluminium is corrosion resistant, which is excellent for sea sides and sandy areas.

Since the 1960’s, Sapa Pole Products has been active in developing sustainable solutions for public spaces. This long history of experience, makes Sapa Pole Products the best partner for your lighting column needs. If you already have a certain design in mind, don’t hesitate to share it with us and we will help you to realize your project.

This brochure hopes to give you an insight into our column capabilities. Our mission is to develop the most innovative, custom made solutions,

together with you and for you. Keeping in mind your specific needs, we would like to contribute to the beautification of your cities and the development of your urban heritage. Technical expertise, passion for aluminium, eye for design, attention to the environment and safety, are the foundation of our Group.

Introduction

Lighting columns have to endure a lot during

their total lifetime: the salty sea wind pushing

against the columns, sand scorching until

they are worn out and dog urine. Sapa Pole

Products has a wide range of standard and

decorative aluminium lighting columns able to

withstand all of these severe circumstances.

By using aluminium, there is no need

for you to paint your columns, which

saves both time and money

Aluminium is corrosion resistant,

which is excellent for sea sides and sandy areas

Develop the most innovative, custom made solutions,

together with you and for you

InTrOduCTIOn InTrOduCTIOn2 3

Sapa pole productS | deSign collection

Sapa Pole Products Sapa Pole Products, part of Sapa Building System, is the leading aluminium lighting column manu fac turer with a production location in the netherlands and local representation in over 20 countries. Our products are CE certified according to the En40 as well as En12899 standard. Sapa Pole Products operates a Quality - and Environmental Manage ment system according to the requirements of ISO 9001 and ISO 14001.

Drunen, The NetherlandsSince the 1960’s Sapa Pole Products has been located in drunen. The product development department of Sapa Pole Products combines the knowledge of aluminium profiles, together with cutting edge lighting column designs, to create a total solution. With our own supplier Sapa Profiles, which is also located in drunen, Sapa Pole Products has flexibility and an optimal guarantee of quality. These are all elements which contribute to the customer’s satisfaction.

Redditch, United KingdomIn 2010 Sapa opened a location in redditch to support the uK market. Sapa Pole Products has a showroom and show garden on this location.

Sapa Pole Products

The leading aluminium lighting

column manu fac turer with a production

location in the Netherlands and local

representation in over 20 countries

The product development department of Sapa Pole Products

combines the knowledge of aluminium profiles, together with

cutting edge lighting column designs, to create a total solution

_________________________________________________________________________________OCAB OCBS Boulevard de la Plaine Pleinlaan, 5 B-1050 BRUSSELS

Phone : + 32 2 509 14 09 Fax : + 32 2 509 14 00 E-mail : [email protected] : www.ocab-ocbs.com

©2004 OCAB/OCBS

Certificate of Conformity (CE-Certificate) 1

Boulevard de la Plaine Pleinlaan, 5 B-1050 BRUSSELS 1148 - CPD – (20)090709

According to the laws in force about the application of the directive 89/106/EEC of the Council of the European Communities of 21 December 1988 regarding the construction products (Construction Products Directive - CPD), it is certified by OCBS-OCAB (notified body Nr 1148) that

Sapa Pole Products Alcoalaan 1, NL-5151 RW Drunen P.O. Box 75, NL-5150 AB Drunen

In its factory of DRUNENapplies a

Factory Production Control (FPC) according to EN 12899 for supports for use with fixed vertical road traffic signs.

The notified body has performed the Initial Type-Testing of the products, the Initial inspection ofthe factory and of the factory production control and achieves the Continuous Surveillance, Assessment and Approval of factory production control imposed by the harmonised standard EN 12899-1:2007.

This certificate stipulates that all the provisos relating to the attestation of conformity described in Annex ZA of the standards under consideration have been applied. This certificate remains valid three years from the date hereunder mentioned and so long as the conditions specified in the harmonised standards, the conditions of production in the factory or the Factory Production Control do not change significantly.

Brussels, July 09, 2009 (update of July 15, 2011) Jacques DEFOURNY, Chairman of the Board

CE certified – En40 CE certified – En12899 ISO 9001 ISO 14001

SAPA POlE PrOduCTS SAPA POlE PrOduCTS

The Sapa GroupSapa is the world leading company in its field and has customers in the building-, transport-, engineering and telecom industry. In 2011 the Sapa Group had combined net sales of 32,995 MSEK and 14,800 employees.

The Sapa Group is organized into three business areas; Building System, Heat Transfer and Profiles. Sapa Profiles, one of the divisions of the Sapa Group, is the world’s largest aluminium extrusions company with 111 presses in 19 countries.

Sapa develops, manufactures and markets value-added

aluminium profiles, profile-based building systems and

heat exchanger solutions in aluminium.

4 5


The properties of aluminiumThe combination of the following properties makes aluminium the optimal material for our products:

• low weight• High strength • Superior malleability • Easy machining • Excellent corrosion resistance• Easy to mill, drill, cut, punch, bend,

weld, bond, tape...

Corrosion resistanceAluminium is an excellent material to use in climate’s with high heat and humidity. This is because aluminium reacts with the oxygen in the air to form an extremely thin layer of oxide, just a few hundredths of a micron thick (1 micron is one thousandth of a millimeter). This layer is dense and provides excellent corrosion protection. If damaged mechanically, the aluminium oxide layer repairs itself immediately.

Soil is not a uniform material. Mineral composition, moisture content, pH, presence of organic materials and electrical conductivity, can all vary widely from site to site. These differences make it difficult to predict a metal’s durability in soil. As a solution to this problem, Sapa Pole Products makes use of corrosion protection tape around the root section of the column.

Our clients have over 40 years of experience in the use of corrosion protection tape for the ground section of the column. This tape is extensively tested by TnO (a dutch independent research organization) to make sure that the protection around root/ground level of our column, meets the current European norms for lighting columns; the En 40-6.

The ground level area of all columns can be liable to damage, for example due to mechanical sweeping, mowing or paving activities. Sapa Pole Products has developed the Ground level protector, which provides optimal protection at ground level around the base of the column. The Ground level protector can either be factory installed by Sapa, or delivered as an accessory, for all Sapa columns. The Ground level protector is supplied in two parts, making it very easy to mount.

Alloy 6000 seriesPure aluminium is relatively soft. Its strength can be increased by alloying or cold working. Most of the aluminium that is commercially available is therefore alloyed with one or more other elements. The resulting alloy has different properties depending on which alloying elements are added. This makes the choice of alloy an important matter.

Sapa Pole Products makes use of the alloy: En-AW 6060 T66. Alloy 5000 series are mostly used for ships because of the corrosion resistance in seawater. Alloy 7000 series are mostly used in the airplane industry because of its exceptional strength. The most optimal alloy for lighting columns is logically alloy 6000 series because of its malleability, ageing capabilities, strength, extrusion possibilities and price-level.

Aluminium, the facts

Did you know that after iron, aluminium is by far the most

widely used metal in the world? This is because aluminium

has a unique combination of attractive properties. Many of these are

extremely important in our efforts to create a more sustainable society.

Our clients have over 40 years

of experience in the use of

corrosion protection tape for the

ground section of the column

The anti-corrosion systems of Sapa Pole Products are extensively

tested by TNO (a Dutch independent research organization) to make

sure that the protection around root/ground level of our column,

meets the current European norms for lighting columns; the EN 40-6

AluMInIuM, THE fACTS AluMInIuM, THE fACTS6 7


for example, did you know that because of the use of aluminium in cars, the weight of the car can be reduced? If we include the production and distribution (wheel-to-wheel) of fuel, a weight reduction of 100 kg in a car means a saving of 10 g of CO2 per kilometer, in other words 2000 kg during the life of the car.

Another example, are the developments around solar energy. Aluminium is often used in solar frameworks, but what makes aluminium so environmentally

Also the European Aluminium Association (EAA)* shows some impressive figures:

• In Europe’s northern countries, up to 92% of the aluminium from beverage cans are recycled, just as 95% of the aluminium from cars and 98% from buildings.

• In denmark, the recycling rate of aluminium from household waste has reached virtually 100% in 2007.

• Today, 40% of Europe’s aluminium supply comes from recycling. It is no wonder then that, 75% of the aluminium ever produced is still in use today.

* Check out the website of the European Aluminium

Association for more information: www.eaa.net

How does Sapa make use of these benefits? Well, Sapa has 9 extrusion cast houses across Europe for recycling. These cast houses have a yearly capacity of 200.000 tons (enough for more than 7 million lighting columns). Sapa Pole Products is committed in different areas when it comes to Corporate Social responsibility. Great examples of these are Carbon neutral and Cradle-to-Cradle columns, explained below.

Climate NeutralAt Sapa Pole Products we are aware that our company can contribute to a better environment. As a production company we can take steps to minimize CO2 emissions. That is why we analyzed our production process with the help of an independent consultancy group (www.ecofys.nl). At different stages in our production process, we have implemented energy savings, and with our patented reinforcement profile, we can reduce the weight of our columns by up to 20%. In 2007, we were the first company within the market to offer climate neutral lighting columns.

Cradle-to-cradle When it comes to ‘green’ certification, there are no bad products, just bad design, say German

chemist Michael Braungart and u.S. architect William Mcdonough, creators of the world’s leading ‘cradle-to-cradle’ (C2C) certification program.

As Braungart and Mcdonough put it, ‘waste equals food’: if a product is properly designed, at the end of its useful life, it can be broken down into its basic elements, which become the ‘nutrients’ for new products. Instead of ‘less waste’, the goal is ‘no waste’. In a C2C model, product materials circulate in an endless cycle with no net effect on the environment. To date, more than 200 companies worldwide have received C2C certification.

A number of European cities and municipalities have embraced C2C sustainability as a strategy to not only protect the environment but to also strengthen people’s welfare and economic prospects through new business opportunities. We are the first aluminium supplier in the world to offer Cradle to Cradle CertifiedCM lighting columns.*

friendly? The most important features are shown below:

• Aluminium is 100% recyclable, time after time.

• recycling aluminium only takes 5% of the energy needed to produce it in the first place.

• There is no downgrade during the recycling process.

• The columns of Sapa Pole products exist of a minimum of 95% recycled material.

Aluminium, the green metal

There are multiple examples within Sapa that show

that aluminium is the ideal material to use when it

comes to sustainable development.

We are the first aluminium supplier in the world

to offer C2C-certified lighting columns

Instead of ‘less waste’,

the goal is ‘no waste’

AluMInIuM, THE GrEEn METAl AluMInIuM, THE GrEEn METAl

* Cradle to Cradle CertifiedCM is a certification mark

of MBdC.

8 9


Aluminum lighting columns up to 20m post top and 18m with bracket, are designed and calculated according to a calculation method in which several factors are taken into account: • Material• reference wind speed• Wind pressures• Terrain category• Safety factors

When these factors, in combination with other criteria are calculated, it can be determined if the lighting column meets the standard. Criteria’s to meet the standard are:

• Strength• Stiffness

Each critical section of the column e.g. base, door section are taken into calcula-tion. Another criteria is the stiffness of the column, regarding horizontal displacement and vertical displacement if the column is to carry a bracket.

Strength calculations

The key factor in delivering a good column is a decent strength calculation.

Sapa Pole Products has the right programs to perform thorough strength

calculations. This way we can guarantee

safety and quality of the columns we

deliver on a day to day basis.

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Ø145 Ø165

Wind speed indicator

Patented reinforcement profileThe columns of Sapa Pole Products are equipped with the VT5+ reinforcement profile that is welded inside the column. This patented profile gives extra strength to the section around the door area. This solution is stronger than type 5, as stated in the European norm En 40-3-3. Independent scientific research shows that besides the tension, the effect of torsion is also reduced.

STrEnGTH CAlCulATIOnS STrEnGTH CAlCulATIOnS

8000

1250

1200

2400

Ø 165

150*

50

700

500

1000

400*

90

2400 Ø 130

2300 Ø 100

Ø 60

3000606004Ø 60

R 350 5°D

L

1 : 60

DA

TED

ES

CR

IPTI

ON

NAME

Sapa Profiles NL B.V.

1-2 -1

Part 1Part 2Part 3

46073165013266012501

Cil. onderpaal 7,30 mEU 1250-05 Top 60 - D60

Aandraaimoment koppeling : 12Nm

Tolerance on Radius between 0 and +10%

37,7 kgThickness:

Weight:3,3 mm

24-09-03

24-09-03

0408016501

Cyl. lighting column 8,00 mAM

R&D

124

-09-

03In

voer

en M

ast

EN AW-6060 T66

Variabel details are mentioned on orderconfirmation

Sapa Pole Products

THIS DRAWING REMAINS PROPERTY OF SAPAB.V. IN DRUNEN AND MAY WITHOUT THE WRITTEN PERMISSIONOF THE OWNER NOT BE MULTIPLIED, BE USED FOR THIRDPARTIES OR BE GIVEN TO THIRD PARTIES FOR PERUSAL.

SCALE

DRAWN BY

SIGN

ORG.DAT

REV.DAT

MUT.DAT

LAST REVISION

REMARKSMATERIAL

TOLERANCES BY EN40UNLESS SPECIFIED OTHERWISE

DIMENSIONS IN MMUNLESS SPECIFIED OTHERWISE

AMERICAN PROJECTION DRAWINGNUMBER

REV

.

24-09-03

b

Sawwedopening

CuttedopeningB B

An

x (0°)

y (270°)

-y (90°)

-n

-x (180°)

-z

z-as

z

+x

Mz;wr

Fz

Mz;wr

Fy

My

Fx Mx

h

M6

M5

M4

M3

M2

M1 w

S2 S1

Sapa Pole ProductsAlcoalaan 1, 5151 RWPostbus 75, 5150 ABDrunen, NetherlandsTel: +31 (0)416-386200Fax: +31 (0)416-386230

STERKTEBEREKENING LICHTMAST volgens EN40-3-3 Blad 1 van 1Date: 4-2-2010

EN40_3_3; juli 2003 Output in italics Sapa Pole ProductsType: Project: Project number: Customer: Berekend:Single bracket Cil. lichtmast 8,00 m 0408016501 FvL

Description Symb. In- Uitvoer UnitNominal column height h 8,000 mBracket length w 1,250 mThe column contains conical sections NoLife span of column 25 JaarLand, zone Netherlands zone 1Land category IILoad factor permanent load f;g 1,200Load factor for wind load f;q 1,200Material: EN AW-6060T66

Material factor m 1,150Representative waarde van de vloeigrens fy;rep 160,000 N/mm2

Elasticiteitsmodulus E 70000,000 N/mm2

Afschuivingsmodulus G 27000,000 N/mm2

Volumieke massa 2700,000 kg/m3

Vibration acceleration ae 0,384 m/s2

Maximum displacement as a result of dead weighte 0,133 mEigenfrequentie fe 1,702 HzDynamic performance factor 1,318Topography factor column anchoring f 1,000

Column does meet standard Symb. Max Uitvoer UnitHorizontal wind displacement 3 10 6,71 %Maximum unit test U.C.max 1,0 0,93Vertical deflection 31,3 17,51 mm

Base d mm FZ N FX N FY N MX Nm MY Nm MZ NmLoads 165,0 438 0 1550 8652 131 635

Zone Ter. Cat. Vref m/s f;g f;q M kg U classe H. V. % U.C.max V. U. mm Max Ac m2

Netherlands zone 3 II 24,5 1,20 1,20 10,0 2 5,99 0,88 21,46 0,385

Door a mm b mm Zd mm gr U.C. Verst. dw tw Mox Moy Mux Muy Tu

D1 416 103 1000 42 0,88 Type 5+ 3,50 10411 14742 3489

Columnd mm t mm hl mm fyd N/mm2 qz N/m2 c Mx Nm My Nm Mz Nm U.C. Remark Position Ac m2 M kg X mmM1 60,0 3,0 700 160,0 1327 1,20 -434 131 635 0,93 Bracket 1 x-asM2 60,0 3,8 200 160,0 1304 1,20 -569 131 635 0,83M3 100,0 3,5 300 160,0 1291 0,90 -780 131 635 0,35M4 100,0 3,5 2000 160,0 1225 0,93 -2503 131 635 0,74M5 130,0 3,3 400 160,0 1142 0,68 -2912 131 635 0,52M6 130,0 3,3 2000 160,0 1093 0,71 -5246 131 635 0,84M7 165,0 3,3 995 160,0 1093 0,51 -6582 131 635 0,69M8 165,0 3,3 394 160,0 1093 0,51 -7140 131 635 0,88 Door (416,103) - y-asM9 165,0 3,3 1011 160,0 1093 0,51 -8652 131 635 0,89

Uith1 d mm t mm hl mm fyd N/mm2 qz N/m2 c Mx Nm My Nm Mz Nm U.C. Remark Ac m2 M kg Y mmS1 60,0 3,0 1250 160,0 1343 1,20 -635 131 0 0,48 Armature: Industria Eclat 0,27 8,00 0

This electronic calculation program has been developed with the utmost care as a support package with your order.The use of this calculation program is at your own risk and responsibility.

Column does meet standard Symb. Max Uitvoer Unit

Horizontal wind displacement 3 10 6,71 %Maximum unit test U.C. max 1,0 0,93Vertical de�ection 31,3 17,51 mm

Strength calculation lighting column according to the EN40-3-3

Result

10 11


Patented reinforcement profile

Crash friendly columns

Have you ever thought of the impact of a car crashing into a tree?

Even with low speeds, a tree crash can be fatal. This is not the case

with aluminium lighting columns from Sapa.

frontal impact

CrASH frIEndly COluMnS CrASH frIEndly COluMnS

Explanation on classificationsImpact speed The 100 (for highways) and 70 (for rural roads) numbers in the family certifications indicate the impact speed of the vehicle.

Performance Level There are three categories of passive safety support structures:• High energy absorbing (HE): slow the vehicle

considerably on impact. The risk of secondary collisions with trees, pedestrians and other road users is reduced, however the severity of the impact for vehicle occupants can be high.

• low energy absorbing (lE): are generally designed to bend in front of and under the impacting vehicle, before shearing or detaching towards the end of the impact.

• non-energy absorbing (nE): permits the vehicle to continue after the impact with a limited reduction in speed. They may therefore provide a lower primary injury risk than energy absorbing support structures, but a higher secondary injury risk if other hazards exist behind the support structure.

Occupant safety level The occupant safety level is based on the results of ASI (Acceleration Severity Index) and THIV (Theoretical Head Impact Velocity). The levels of 1, 2 and 3 provide increasing levels of safety, in that order, by reducing impact severity.

Non-energy absorbing (NE) lighting columnsnE3 is the safest passive safe classification for medium and high speed roads. The impact speed of non-energy absorption (nE), combined with the 3rd occupant safety level, demand special requirements of a column. Sapa Pole Products has developed a special shear-off solution. This in-built solution is unique, as it will shear-off in the event of an impact, and is unaffected by the direction of the impact. The solution is based just above the ground level of the column.

High energy absorbing (HE) lighting columnsIn urban areas where risk of a secondary impact is high, lighting columns require a high energy absorbing classifi-cation. The best high energy absorbing classification for the occupants is HE3. To obtain the HE3 classification, a patented ‘catch-up’ construction is integrated into the column. The construction ensures that during an impact, the speed of the vehicle is heavily reduced, whilst at the same time, guaranteeing maximum occupant safety.

Available family classifications

note: The 3 behind nE is much better for the occupant safety

then the 3 behind lE or HE.

Energy level

Occupant

Safety

Level

70nE3 100nE3

70nE2 100nE2 100lE3

100nE1 100lE2 100HE2

100lE1

Crash tests Since the 1970’s, Sapa Pole Products has been conducting crash tests, to investigate the safest constructions for your roads. This long history of building up knowledge on this topic, has resulted in a range of safe, secure and sustainable aluminium solutions, for all of your lighting needs. We give you the opportunity to design and create safe roads with fully Certified (and endorsed by a notified Body) passively safe columns in all shapes and sizes.

The use of crash friendly, also referred to as passively safe lighting columns, traffic signals and sign posts, are becoming increasingly important on both highways and rural roads. The European standard En 12767 specifies performance requirements for passively safe support structures for permanent road equipment. It both defines and limits the levels of occupant injury severity when impacting these structures.

12 13


Powdercoating An electrostatic powder-coated finish is available in a range of colors. rAl colors as well as dB colors or maybe even your own PMS color that suits the municipality. On this page you can see an indication, but they can differ in real life.

Surface treatment

As explained earlier, the corrosion resistance of aluminium is excellent.

This is why there is no need to give aluminium columns a surface treatment.

However, if a street image needs a certain color or design, there are

of course possibilities to treat the surface with a coating or anodizing.

Anodizing Anodizing is one of the most common methods of surface treatment for alu minium, which gives the column a nice matt-silver appearance. The advan ta ges of anodizing are that it increases corrosion durability, is a dirt-repellent surface, offers a decorative finish with constant color and glow, is a touch friendly surface and a functional surface.

Decoline Are you searching for a lighting column with the look of wood, and yet prefer aluminium? decoline is the answer. Thanks to a unique and innovative process, Sapa Pole Products is able to produce columns in a range of decorative designs never before thought possible. It is also possible to create your own surface texture. The special Qualicoat coating guarantees colorfastness and offers optimal protection against the influence of weather and uV radiation.

The advan ta ges of anodizing are that it increases corrosion

durability, is a dirt-repellent surface, offers a decorative finish

with constant color and glow, is a touch friendly surface and

a functional surface

SurfACE TrEATMEnT SurfACE TrEATMEnT14 15


natural anodized Brushed finished

Twist-on ground wingsEasy-to-install, twist-on ground wings prevent columns from rotating in the ground (available in all lighting column diameters).

Corrosion protection tapeSapa has over 40 years of experience in the use of corrosion protection tape for the ground portion of the column. This tape is extensively tested by TnO (a dutch independent research organization) to make sure that the protection around ground level of our column meets the current European norms for lighting columns, the En 40-6.

Ground level protector The ground level area of all columns can be liable to damage, for example due to mechanical sweeping, mowing or paving activities. Sapa Pole Products has developed the ground level protector, which provides optimal protection at ground level around the base of the column. The ground level protector can either be factory installed by Sapa, or delivered as an accessory, for all Sapa columns. The ground level protector is supplied in two parts, making it very easy to mount.

AlulockWith the introduction of the double sliding lock, Sapa has put an end to doors that stick or jam. The door section of our column is easy to operate and last the lifetime of the column. A door lock fitted with our special vandal-proof Alulock, can only be opened with a special Alulock key. The Alulock is universally available and can be purchased separately for all Sapa lighting columns.

Accessories for root-mounted columns

Columns that can be directly buried in the ground, or root-mounted columns, are also an option. For these columns we have to following accessories:

Twist-on ground platesEasy-to-install, twist-on ground plates prevent columns from sinking into the ground (available in all lighting column diameters).

Accessories

Sapa Pole Products provides basic accessories for different types of surfaces

and for the protection of columns.

ACCESSOrIES ACCESSOrIES

for the protection of lighting and flagpole columns, we introduced the Ground level protector to the market. doors are often a target for vandalism, therefore we developed the Alulock.

for installation in areas where root sections are not possible, we provide base-plates.

To make sure that the columns do not rotate in the ground, we offer special ground wings.

To prevent the sinking of columns into the ground, we offer universal ground plates.

Base-plates for the installation of lighting columns on concrete foundations, bridges and viaducts, Sapa Pole Products supplies cast-aluminium base-plates for all types of lighting columns. We also have a one piece base-plate which is factory-fitted to the column during the production process. This gives the column a nice esthetical finish. If you prefer delivery of the base-plate seperate from the column, there is also a possibility to order a two-part base plate, which can be assembled during installation and benefit from transport savings. Welded base-plates are also available.

16 17


All columns in this brochure have been calculated according to the following variables:

• A minimum life expectancy of 25 years.• Average wind speed varying from 20 m/s to 40 m/s and

a corresponding maximum wind speed (3-sec gust wind speed) of 115 km/h to 227 km/h.

• Columns up to 6 meters height have been calculated to carry a lantern with a maximum surface area of 0,12 m2 and 12 kg weight.

• Columns from 7 meters and higher are calculated to carry a lantern with a maximum surface area of 0,15 m2 and 15 kg weight.

All columns need to be calculated for each specific situation. If you want to be sure that the columns which you have chosen are right for your specific situation, please contact us to have a calculation made.

Collections of Sapa columns

Sapa has over 3000 column types. We can make columns in every

shape or size you wish for. For your convenience, Sapa has developed

9 collections of columns that are suitable for all kinds of purposes.

Collection 1: Bouquet

Collection 2: Twins

Collection 3: Curve

Collection 4: Nautic

Collection 5: Quadro

Collection 6: Torch

Collection 7: Surf

Collection 8: Mystic

Collection 9: Fusion

25COllECTIOnS Of SAPA COluMnS COllECTIOnS Of SAPA COluMnS18 19


H2

Doo

r

H1

D

90

60

LPH

W

Collection 1: Bouquet

The Bouquet collection can be used for all types of

purposes. from parks to small streets (height 4-6 m) to

decorative areas in an urban surrounding (height 4-8m).

It is a modest and elegant column. If you would like a

more playful column, you can vary the height and the

curve of the bracket.

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Ø120x3 mm

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Ø145x3mm

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

4 m

6 m

8 m

Ø145x3 mm

Ø145x3 mm Ø165x3.3 mm

Ø175x4 mm Ø200x4 mm

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

5 m Ø120x3 mm Ø145x3 mm


LPH 4m 5m 6m 8m

d 120 145 120 145 145 165 175 200

H1 1800 1800 1800 1800

door 500 x 85 500 x 85 500 x 85 500 x 115 600 x 115

H2 1000 1000 1000 1000

W (type A) 750;1000 750;1000 750;1000 750;1000

W( type B) 1000 1000 1000 1000

# Brackets 1 - 4 1 - 4 1 - 4 1 - 4

COllECTIOnS Of SAPA COluMnS COllECTIOnS Of SAPA COluMnS

Type A

Type B

Type A Type B Type A Type A

20 21


25°

D

H1

76

60

H2

Doo

r

W

LPH

Collection 2: Twins

The Twins collection is especially suitable for

parks and small streets (height 6m), but also for

roads that have footpaths or cycle paths next to

them (height 8 m). Starting from a single shaft,

the column finishes in a double bracket above.

The smooth transition from the column into the

bracket makes the column nice and elegant.

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

6 m Ø145x4.3 mm

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

8 m Ø175x4 mm


LPH 6m 8m

d 145 175

H1 1455 1980

door 500 x 85 600 x 115

H2 600 1000

W (type A)* 1850 2050

W (type B)* 1650 1850

*Both available in High and low (-500 mm)


Type BType A

Type A Type A Type B Type B

22 23


D

H1

25°

76

LPH

H2

Doo

r

W

Collection 3: Curve

The Curve will especially fit urban roads and perimeter

roads and are available in a height from 6 to 8 meters.

The shaft is conical bent column which allows different

brackets to be fitted at the top of the column. for more

bracket possibilities, please have a look at the bracket

section of this chapter.

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

6 m Ø145x4.3 mm

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

8 m Ø175x4 mm


LPH 6m 8m

d 145 175

H1 1455 1980

door 500 x 85 600 x 115

H2 600 1000

W (type A)* 1850 2050

W (type B)* 1650 1850

*Both available in High and low (-500 mm)


Type A Type A Type BType B

Type A Type A Type B Type B

24 25


H1

W

LPH

76

D

H2

Doo

r

LPH 5m 6m 8m

d 145 165 165 200 200 165

H1 1800 1800 1800

door 500 x 85 500 x 115 500 x 115 600 x 115

H2 1000 1000 1000

W 750;1000;1250;1500 750;1000;1250;1500 750;1000;1250;1500

# Brackets 1 - 2 1 - 2 1 - 2

Collection 4: Nautic

Imagine a harbor with lighting columns that match the

ships. The nautic column is clearly inspired by the mast

of a sailing ship. The column lends itself well to Harbours

or Boulevard streetscapes, but also in parks and small

streets. The nautic is available in the heights from 5 to

8 meters.

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Ø145x3 mm

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Ø145x3mm

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Ø200x3.3mm

5 m

6 m

8 m

Ø165x3.3mm

Ø165x3.3 mm Ø200x3.3mm


COllECTIOnS Of SAPA COluMnS COllECTIOnS Of SAPA COluMnS26 27


H2

Doo

rH1

120x120

90

76

W

LPH

Collection 5: Quadro

As the name says, the base of the Quadro is made

of a square profile. This gives the column a robust

appearance. The round top of the column will allow it to fit

in every street image you are designing for. The collection

is designed for parks, squares and small streets. This is

why the maximum height is 6 meters.

LPH 4m 5m 6m

H1 2100 2500 3000

door 400 x 85 400 x 85 400 x 85

H2 1000 1000 1000

W 500;750;1000 500;750;1000 500;750;1000

# Brackets 0 - 2 0 - 2 0 - 2

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Ø145x3mm

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

120x120 mm

4 m

5 m

6 m

120x120 mm

120x120 mm




H1

120

200

LPH

Do

or

H2

W

Collection 6: Torch

The base of the Torch is an inverted conical pole.

At the end of the column you can choose one, two

or three brackets. The special shape of this column

fits especially well in shopping areas and parks.

The height varies from 4 to 6 meters.

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Ø120x3 mm

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

4 m

6 m

Ø145x3 m

m

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

5 m

3x Bracket 600 mm

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

4 m

6 m

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

5 m

3x Bracket 1000 mm

Ø120x3 mm

Ø145x3 m

m

Ø120x3 mm

Ø145x3 m

m

Ø120x3 mm

Ø145x3 m

m

Ø120x3 mm

Ø145x3 m

m

Ø120x3 mm

Ø145x3 m

m


LPH 4 5m 6m

d 120 145 120 145 120 145

H1 1200 1200 1200

door 500 x 85 500 x 85 500 x 85

H2 600 600 600

W 600;1000 600;1000 600;1000

# Brackets 1 - 3 1 - 3 1 - 3



LPH

H1

D

9075°

W

H2D

oor

Collection 7: Surf

lighting columns with a high and a low bracket and lantern

are often seen in public areas. The Surf is a special version

of this kind of columns. There are two different types of the

Surf: columns with brackets that have a small distance in

height (6-10 m) and columns with brackets that have a big

distance in height (4 & 6 m). Especially the last one can be

used for roads that have footpaths or bicycle paths next to

them, or for decorative purposes in urban areas.

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Ø145x3 mm

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Ø145x3mm

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

6 m

8 m

10 m

Ø165x3.3 mm



20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

4&6 m Ø145x3 mm Ø165x3.3 mm


LPH 6m 8m 10m 4&6m

d 145 165 165 200 200 145 165

H1 1800 1800 1800 1800

door 500 x 85 500 x 115 600 x 115 600 x 115 500 x 85 500 x 115

H2 1000 1000 1000 1000

W 750;1000;1250 750;1000;1250 750;1000;1250 1000

# Brackets 1 - 2 1 - 2 1 - 2 2



H1

H2

Doo

r

140

76

60

W

LPH

Collection 8: Mystic

In old city centers, the Mystic will be the ideal column

for you. A classic column with a modern touch to it.

It is based upon questions raised from the Arabic market,

but also inspired by existing developed columns for old

city centres in the netherlands. The Mystic collection

is available in heights from 4 to 6 meters.

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Type I

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

4 m

6 m

Type II

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

5 m Type I Type II

Type I Type II


LPH 4m 5m 6m

H1 2100 2100 2100

door 500 x 95 500 x 95 500 x 95

H2 1000 1000 1000

W* 600;800;1000 600;800;1000 600;800;1000

*Bracket lengths available for both types


Type A

Type B

34 35


H1

85

D

Doo

r

H2

LPH

750

Collection 9: Fusion

next to modern buildings, modern lighting columns

are an ideal fit, to complete a street image. Still, some

city’s have also an ancient feel to them. The fusion

Collection tries to build a bridge between old and

new, so it is ideal for new and old city surroundings

alike. The height varies from 4 to 8 meters.

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Ø145x3 mm

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Ø145x3mm

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Ø145x3mm

4 m

5 m

6 m

20 25 30 35 40 Vref(10min.)

[m/s]

120 140 160 180 200 220 Vref(3s.)

[km/h]

Ø200x4mm8 m


LPH 4m 5m 6m 8m

d 145 145 145 200

H1 1800 1800 1800 1800

door 500 x 85 500 x 85 500 x 85 500 x 115

H2 1000 1000 1000 1000

W 750 750 750 750

# Brackets 0 - 2 0 - 2 0 - 2 0 - 2



Brackets

Like columns, brackets come in all shapes and sizes. On the previous pages

you have already seen a great collection of the brackets which are available.

To inspire you some more, on this page we show you what we can offer.

BrACKETS BrACKETS

If you have something else in mind,

please let us know so that we may

make a custom made design

Type 8Type 1

Type 6

Type 4

Type 2 Type 3

Type 5

Type 7

38 39


Worldwide projects

WOrldWIdE PrOjECTS

Schiphol Airport – netherlands

rabat – Morocco

Ankara – Turkey

london – united Kingdom

Auckland – new-Zealand

Sydney – Australia Brussels – BelgiumShuaiba refinery – Kuwait rome – ItalyAdelaide – Australia Berlin – Germany

WOrldWIdE PrOjECTS40 41


www.sapapoleproducts.com

Sapa Pole Products

Postal address

P.O. Box 75

nl-5150 AB drunen

netherlands

Sap

a P

ole

Pro

duct

s r

ev. 2

Exp

des

Col

, Sub

ject

to p

rodu

ct c

hang

es, m

ispr

ints

and

prin

ting

erro

rs

Visiting address

Alcoalaan 12

nl-5151 rW drunen

netherlands

Phone +31 416 386 200

Fax +31 416 386 230

Email [email protected]

Website www.sapapoleproducts.com

Design Collection

Documents

Transcript of Design Collection