DEP-00.00.05.05-GEN

DEP SPECIFICATION

GLOBAL TECHNICAL STANDARDS INDEX

DEP 00.00.05.05-Gen.

February 2013

ECCN EAR99

DESIGN AND ENGINEERING PRACTICE

© 2013 Shell Group of companies All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, published or transmitted, in any form or by any means, without the prior

written permission of the copyright owner or Shell Global Solutions International BV.

This document contains information that is classified as EAR99 and, as a consequence, can neither be exported nor re-exported to any country which is under an embargo of the U.S. government pursuant to Part 746 of the Export Administration Regulations (15 C.F R. Part 746) nor can be made available to any national of such country. In addition, the information in this document cannot be exported nor re-exported to an end-user or for an end-use that is prohibited by Part 744 of the Export

Administration Regulations (15 C.F.R. Part 744).

Co

pyr

igh

t S

hel

l Gro

up

of

Co

mp

anie

s. N

o r

epro

du

ctio

n o

r n

etw

ork

ing

per

mit

ted

wit

ho

ut

licen

se f

rom

Sh

ell.

No

t fo

r re

sale

This document has been supplied under license by Shell to:Shell [email protected] 21/05/2013 21:04:59

ECCN EAR99 DEP 00.00.05.05-Gen. February 2013

PREFACE

DEP (Design and Engineering Practice) publications reflect the views, at the time of publication, of Shell Global Solutions International B.V. (Shell GSI) and, in some cases, of other Shell Companies.

These views are based on the experience acquired during involvement with the design, construction, operation and maintenance of processing units and facilities. Where deemed appropriate DEPs are based on, or reference international, regional, national and industry standards.

The objective is to set the standard for good design and engineering practice to be applied by Shell companies in oil and gas production, oil refining, gas handling, gasification, chemical processing, or any other such facility, and thereby to help achieve maximum technical and economic benefit from standardization.

The information set forth in these publications is provided to Shell companies for their consideration and decision to implement. This is of particular importance where DEPs may not cover every requirement or diversity of condition at each locality. The system of DEPs is expected to be sufficiently flexible to allow individual Operating Units to adapt the information set forth in DEPs to their own environment and requirements.

When Contractors or Manufacturers/Suppliers use DEPs, they shall be solely responsible for such use, including the quality of their work and the attainment of the required design and engineering standards. In particular, for those requirements not specifically covered, the Principal will typically expect them to follow those design and engineering practices that will achieve at least the same level of integrity as reflected in the DEPs. If in doubt, the Contractor or Manufacturer/Supplier shall, without detracting from his own respons bility, consult the Principal.

The right to obtain and to use DEPs is restricted, and is typically granted by Shell GSI (and in some cases by other Shell Companies) under a Service Agreement or a License Agreement. This right is granted primarily to Shell companies and other companies receiving technical advice and services from Shell GSI or another Shell Company. Consequently, three categories of users of DEPs can be distinguished:

1) Operating Units having a Service Agreement with Shell GSI or another Shell Company. The use of DEPs by these Operating Units is subject in all respects to the terms and conditions of the relevant Service Agreement.

2) Other parties who are authorised to use DEPs subject to appropriate contractual arrangements (whether as part of a Service Agreement or otherwise).

3) Contractors/subcontractors and Manufacturers/Suppliers under a contract with users referred to under 1) or 2) which requires that tenders for projects, materials supplied or - generally - work performed on behalf of the said users comply with the relevant standards.

Subject to any particular terms and conditions as may be set forth in specific agreements with users, Shell GSI disclaims any liability of whatsoever nature for any damage (including injury or death) suffered by any company or person whomsoever as a result of or in connection with the use, application or implementation of any DEP, combination of DEPs or any part thereof, even if it is wholly or partly caused by negligence on the part of Shell GSI or other Shell Company. The benefit of this disclaimer shall inure in all respects to Shell GSI and/or any Shell Company, or companies affiliated to these companies, that may issue DEPs or advise or require the use of DEPs.

Without prejudice to any specific terms in respect of confidentiality under relevant contractual arrangements, DEPs shall not, without the prior written consent of Shell GSI, be disclosed by users to any company or person whomsoever and the DEPs shall be used exclusively for the purpose for which they have been provided to the user. They shall be returned after use, including any copies which shall only be made by users with the express prior written consent of Shell GSI. The copyright of DEPs vests in Shell Group of companies. Users shall arrange for DEPs to be held in safe custody and Shell GSI may at any time require information satisfactory to them in order to ascertain how users implement this requirement.

All administrative queries should be directed to the DEP Administrator in Shell GSI.



TABLE OF CONTENTS

PART I INTRODUCTION ........................................................................................................ 4 1.1 SCOPE ........................................................................................................................ 4 1.2 DEPS AND OTHER TYPES OF TECHNICAL STANDARDS .................................... 4 1.3 STANDARD DRAWINGS, STANDARD FORMS AND REQUISITIONS .................... 5 1.4 DISTRIBUTION OF DEPS .......................................................................................... 5 1.5 DISTRIBUTION OF OTHER GLOBAL TECHNICAL STANDARDS ........................... 5 1.6 AMENDMENTS .......................................................................................................... 5 1.7 CUSTODIANSHIP ...................................................................................................... 5 1.8 SUMMARY OF MAIN CHANGES ............................................................................... 5 1.9 COMMENTS ON THIS DEP ....................................................................................... 6

PART II CURRENT STANDARDS LISTED BY ENGINEERING DISCIPLINE ....................... 7 1. ADMINISTRATIVE (INDICES) ................................................................................... 7 2. ADMINISTRATIVE (TECHNICAL STANDARDS TEAM) .......................................... 7 3. ANALYTICAL ............................................................................................................. 7 4. CIVIL, STRUCTURAL & OFFSHORE ....................................................................... 7 5. ELECTRICAL ........................................................................................................... 10 6. HEALTH .................................................................................................................... 11 7. MECHANICAL, MATERIALS & INTEGRITY ........................................................... 11 8. OPERATIONS EXCELLENCE & ASSET MANAGEMENT ..................................... 14 9. PETROLEUM ENGINEERING ................................................................................. 15 10. PIPELINES, FLOW ASSURANCE SYSTEMS & SUBSEA ..................................... 15 11. PROCESS AUTOMATION, CONTROL, AND OPTIMIZATION .............................. 17 12. PROCESS ENGINEERING ...................................................................................... 17 13. TECHNICAL SAFETY ENGINEERING .................................................................... 18 14. PROJECT SERVICES .............................................................................................. 19 15. QUALITY ASSURANCE .......................................................................................... 19 16. ROTATING EQUIPMENT ......................................................................................... 19 17. TELECOMS .............................................................................................................. 20 18. UTILITIES & HEAT TRANSFER .............................................................................. 20 19. WELLS ENGINEERING ........................................................................................... 21

PART III NUMERICAL LISTING ............................................................................................. 22

PART IV REFERENCES ......................................................................................................... 52



PART I INTRODUCTION

1.1 SCOPE

This index lists the global technical standards in circulation on the date of issue.

In Part II, the current set of standards is listed, organized by engineering discipline. In Part III, the standards are listed in numerical order. Part III also shows standards that have been withdrawn. The Custodian of each standard is also shown in Part III.

In addition to DEPs, this index includes other types of global technical standards administered by the Technical Standards Group; see (Part I, 1.2).

Standard drawings, standard forms and standard requisitions are not covered in this index, as they are covered in separate indices; see (Part I, 1.3).

This index replaces the previous index dated September 2012; see (Part I, 1.8) regarding the main changes.

1.2 DEPS AND OTHER TYPES OF TECHNICAL STANDARDS

The DEPs and other technical standards administered by the Technical Standards Group are classified as follows:

Classification Type Purpose/Comment

DEP-Gen. DEP-Specification(1)

For project use in engineering, procurement and construction. Provides a basis for understanding between the Principal, Contractor and Manufacturer/Supplier, specifying requirements for a product, process or service

DEP-Informative(2) A companion document to the DEP Specification of the same number. Explains the reasons for certain requirements in the DEP Specification and contains background information. For Shell use – not intended to be given to Engineering Contractor or Manufacturers/Suppliers.

DWS-Gen. Deepwater Standard(3)

Restricted access within Shell only. Provides a basis for understanding between the Principal, Contractor and Manufacturer/Supplier, specifying requirements for a product, material or process specifically for deepwater installations.

RMP-Gen. Run & Maintain Practice(4)

For internal Shell use. A temporary document containing run and maintain content formerly in the DEPs that will be moved into the business operating frameworks. Applies to the “operate, inspect and maintain” phase of an asset life.

NOTES: 1. Distributed via “Shell DEPs Online”. Distributed under license agreement to authorised Customers and, where necessary, to Shell nominated Contractors and Manufacturers/Suppliers.

2. Distributed for use within Shell and to authorised, select Customers via “Shell DEPs Online”. 3. Restricted access within Shell via the Technical Standards Portal. 4. Access within Shell via the Technical Standards Portal.

Wells Standards have been withdrawn from the DEP sytem and are no longer administered by the Technical Standards Group. In Shell, information on Wells Standards is provided through the following web site:

http://sww.shell.com/pt/business units/wells/technical assurance standards/TA.html


http://sww.shell.com/pt/business_units/wells/technical_assurance_standards/TA.html


1.3 STANDARD DRAWINGS, STANDARD FORMS AND REQUISITIONS

Standard Drawings are indexed in DEP 00.00.06.06-Gen.

Standard Forms are indexed in DEP 00.00.10.05-Gen.

Requisition sheets are indexed in DEP 30.10.01.10-Gen.

1.4 DISTRIBUTION OF DEPS

Shell companies are provided access to the DEPs through “Shell DEPs Online” at https://www.shelldeps.com.

Authorised recipients of the DEPs are entitled to receive the DEPs via configured access to the “Shell DEPs Online” at https://www.shelldeps.com. The authorised company is responsible for providing DEPs to their Contractors and Manufacturers. NOTE: DEP Informatives are for internal use and are not to be distributed outside of Shell, except under

license agreement to authorised select Customers only.

In the past, each version of the DEPs has been released on a separate DVD-ROM. The distribution via DVD-ROM has been discontinued. Current and future releases of the DEPs will be distributed exclusively using the Shell DEPs Online system.

1.5 DISTRIBUTION OF OTHER GLOBAL TECHNICAL STANDARDS

Global Technical Standards other than DEPs, as described in (Part I, 1.2), are made available via the Technical Standards web portal at sww.shell.com/standards. Updates to these documents generally coincide with the distribution of the DEPs as described in (Part I, 1.4).

Standard Drawings, Standard Forms and Requisitions are distributed via “Shell DEPs Online” in the same manner as DEPs.

1.6 AMENDMENTS

Between formal revisions, if an amendment is required to a standard, an Amendment is issued. These Amendments are numbered A0x, where "x" is a sequential number of the amendments for the particular document.

Amended standards are indicated in the 2nd column of Part III of this index.

1.7 CUSTODIANSHIP

The Custodians responsible for active standards are identified in the 4th column of the numerical index (Part III).

1.8 SUMMARY OF MAIN CHANGES

This index is a revision of the index of the same number dated September 2012. The main, non-editorial changes are to update the index to reflect the current status with version 36 of the DEPs.

In Part III, changes are indicated by a vertical line (|) in the left margin of the index. The specific changes are shown in red text.


https://www.shelldeps.com/


http://sww.shell.com/standards


1.9 COMMENTS ON THIS DEP

Comments on this DEP may be submitted to the Administrator using one of the following options:

Shell DEPs Online

(Users with access to Shell DEPs Online)

Enter the Shell DEPs Online system at https://www.shelldeps.com

Select a DEP and then go to the details screen for that DEP.

Click on the “Give feedback” link, fill in the online form and submit.

DEP Feedback System (Users with access to Shell Wide Web)

Enter comments directly in the DEP Feedback System which is accessible from the Technical Standards Portal http://sww.shell.com/standards.

Select “Submit DEP Feedback”, fill in the online form and submit.

DEP Standard Form (Other users)

Use DEP Standard Form 00.00.05.80-Gen. to record feedback and email the form to the Administrator at [email protected].

Feedback that has been registered in the DEP Feedback System by using one of the above options will be reviewed by the DEP Custodian for potential improvements to the DEP.



http://sww.shell.com/standards

mailto:[email protected]


PART II CURRENT STANDARDS LISTED BY ENGINEERING DISCIPLINE

1. ADMINISTRATIVE (INDICES)

DEP Number Title

DEP 00.00.05.05-Gen. Global technical standards index

DEP 00.00.06.06-Gen. Standard drawings index

DEP 00.00.10.05-Gen. Standard forms index

DEP 30.10.01.10-Gen. Requisitions index

2. ADMINISTRATIVE (TECHNICAL STANDARDS TEAM)

DEP 00.00.00.30-Gen. Procedure for global technical standards publications

DEP 00.00.07.10-Gen. Design class tables

DEP 00.00.07.30-Gen. Application of a functional specification (endorsement of ISO 13879, ISO 13880 and ISO/TR 13881)

DEP 00.00.20.10-Gen. The use of SI quantities and units (endorsement of ISO/IEC 80000)

3. ANALYTICAL

DEP 32.31.56.30-Gen. Implementation of near-infrared systems for main fuels blending

DEP 34.17.10.31-Gen. Laboratories

4. CIVIL, STRUCTURAL & OFFSHORE

DEP 30.46.00.31-Gen. Thermal insulation

DEP 30.48.00.34-Gen. Phosphate-conversion coatings for marine equipment

DEP 30.48.30.31-Gen. Cement lining of pipes (based on EN 10298)

DEP 30.48.60.12-Gen. Design and installation of chemical-resistant protection systems for concrete surfaces (based on EN 14879-Parts 1, 3, 5 and 6)

DEP 31.06.15.10-Gen. Marine loading arms (amendments/supplements to OCIMF design and construction specification for marine loading arms)

DEP 31.40.10.22-Gen. Top Tension Riser Tensioning Systems

DEP 34.00.01.10-Gen. Earthquake design for onshore facilities - Seismic hazard assessment

DEP 34.00.01.30-Gen. Structural design and engineering of onshore structures

DEP 34.11.00.10-Gen. Onshore & Nearshore Site investigations

DEP 34.11.00.11-Gen. Site preparation and earthworks including tank foundations and tank farms

DEP 34.11.00.12-Gen. Geotechnical and foundation engineering – onshore

DEP 34.13.20.31-Gen. Roads, paving, surfacing, cable trenches, slope protection and fencing

DEP 34.14.20.31-Gen. Drainage systems and primary treatment facilities

DEP 34.17.00.32-Gen. Design and engineering of buildings

DEP 34.17.10.30-Gen. Design of blast resistant onshore buildings, control rooms and field auxiliary rooms

DEP 34.17.10.33-Gen. Portable blast resistant modules

DEP 34.17.10.34-Gen. Requirements for mobile and construction camps

DEP 34.19.19.11-Gen. Grouting of equipment and structure bases

DEP 34.19.20.11-Gen. Passive fire protection for onshore facilities



DEP 34.24.26.31-Gen. Chimneys selection, design and engineering (based on EN 1992-1-1, EN 1993-3-2, EN 1443, EN 13084 Parts 1, 2, 4, 5, 6, 7 and 8)

DEP 34.28.00.31-Gen. Onshore steel structures

DEP 34.28.00.33-Gen. Onshore ancillary steel structures

DEP 34.51.01.32-Gen. Full containment refrigerated LNG tanks

DEP 34.51.01.34-Gen. Full containment refrigerated LPG tanks

DEP 35.00.00.10-Gen. Vessel Integrity, Marine Systems - Requirements for Selection and Operation of Vessels (Endorsement of DNV RP-H104)

DEP 35.00.10.10-Gen. Design of jetty facilities (amendments/supplements to BS 6349-1/2/4)

DEP 37.00.10.10-Gen. Metocean design and operating considerations (endorsement of ISO 19901-1:2005)

DEP 37.00.10.11-Gen. Metocean data acquisition – definition, implementation and analysis

DEP 37.00.10.12-Gen. Metocean data acquisition - Real time systems

DEP 37.01.10.11-Gen. Design of offshore topsides facilities against fire and blast loading (amendments/supplements to API RP-2FB)

DEP 37.11.00.30-Gen. Site specific assessment of mobile offshore jack-up units

DEP 37.14.10.10-Gen. Drain systems for offshore installations

DEP 37.17.10.10-Gen. Design of offshore living quarters

DEP 37.17.10.11-Gen. Design of offshore temporary refuges

DEP 37.19.00.10-Gen. Offshore structures - General requirements (endorsement of ISO 19900)

DEP 37.19.00.12-Gen. Offshore topsides structures (amendments/supplements to ISO 19901-3:2010)

DEP 37.19.00.14-Gen. Seismic design procedures and criteria - offshore (amendments/supplements to ISO 19901-2)

DEP 37.19.00.30-Gen. Fixed steel offshore structures (amendments/supplements to ISO 19902:2007)

DEP 37.19.10.30-Gen. Weldable structural steels for fixed offshore structures (amendments/supplements to EN 10225 and EN 10025)

DWS 37.19.20.11-Gen. Weight management plan for floating platforms (amendments/supplements to ISO 19901-5)

RMP 37.19.60.50-Gen. Structural inspection of offshore installations

DEP 37.81.00.11-Gen. Offshore coordination team management and construction hook-up work planning

DEP 37.81.10.10-Gen. Generic design and analysis for steel catenary risers and catenary umbilical systems for offshore structures

DWS 37.81.10.11-Gen. Design and analysis of top tension risers for deepwater offshore floating structures (based on API RP 2RD/ISO WD 13628-12)

DEP 37.81.10.12-Gen. Design of anchor piles for deepwater mooring systems (based on API RP 2SK)

DEP 37.81.10.13-Gen. Global design and analysis of permanently moored deepwater floating production systems (amendments/supplements to API RP 2FPS, API RP 2SK and API RP 2SM)

DEP 37.81.10.14-Gen. Global design and analysis of deepwater tension leg platforms (amendments/supplements to API RP-2T)

DWS 37.81.10.18-Gen. Design specification for deepwater tension leg platform, semisubmersible and spar hull (based on API RP 2T and API RP 2FPS)

DEP 37.81.10.19-Gen. Marine operations requirements - loadout, transportation and installation deepwater structures (amendments/supplements to ISO 19901-6 or API RP 2MOP)

DEP 37.81.10.20-Gen. Design of driven pile foundations for tension leg platforms (based on API RP 2T)

DEP 37.81.10.21-Gen. Structural design of tendon systems for deepwater offshore tension leg platforms (amendments/supplements to API RP 2T)

DEP 37.81.10.30-Gen. Design, fabrication and testing requirements for deepwater project VIV suppression strakes for SCR's, TTR's, umbilicals, TLP tendons and jumpers

DEP 37.81.10.31-Gen. Structural steel design of small deepwater offshore skids, facility packages, and subsea sleds and manifolds (based on AISC Steel Construction Manual ASD, API RP 2A-WSD and AWS D1.1)



DEP 37.81.10.32-Gen. Structural steel fabrication of small deepwater offshore skids, facility packages, and subsea sleds and manifolds (based on AISC steel construction manual ASD, API RP 2A-WSD and AWS D1.1)

DEP 37.81.10.33-Gen. Structural welding and inspection of deepwater floating production systems (amendments/supplements to AWS D1.1/D1.1M:2008)

DEP 37.81.10.34-Gen. Structural fabrication of deepwater floating production systems

DWS 37.81.10.36-Gen. Structural steel design of deepwater offshore topsides decks for floating systems

DEP 37.81.10.38-Gen. Design, fabrication and testing requirements of permanent VIV suppression fairing systems for offshore structures

DEP 37.81.20.30-Gen. Manufacture, testing, and inspection of carbon and low-alloy steel castings Grades 345-586 N/mm2 (50-85 KSI) for primary steel applications in deepwater offshore structures and pipelines

DEP 37.81.20.33-Gen. Manufacture, testing, and inspection of weldable structural steel plate grades 345 552 N/mm2 (50-80 ksi) for special/critical steel applications in deepwater offshore structures (based on ASTM A20)

DEP 37.81.20.34-Gen. Manufacture, testing, and inspection of weldable structural steel plate grades 345-552 N/mm2 (50-80 ksi) for primary steel applications in deepwater offshore structures (based on ASTM A6)

DWS 37.81.20.35-Gen. Technical specification for elastomeric flexible joints for use in deepwater offshore dynamic riser applications

DEP 37.81.20.36-Gen. Syntactic foam buoyancy modules for use in deepwater offshore dynamic riser applications

DEP 37.81.20.37-Gen. Manufacture, testing, and inspection of carbon and low-alloy steel forgings for special/critical steel applications in deepwater offshore structures and pipelines

DEP 37.81.20.38-Gen. Manufacture, testing, and inspection of weldable structural rolled shapes grades 345-483 N/mm2 (50-70 KSI) for primary steel applications in deepwater offshore structures (based on ASTM A6)

DEP 37.81.20.39-Gen. Manufacture, testing, and inspection of carbon and low-alloy steel forgings for primary steel applications in deepwater offshore structures and pipelines (based on ASTM A788, ASTM A961 and MSS SP-75)

DEP 37.81.21.30-Gen. Manufacture, testing, and inspection of permanent mooring system chain and accessories for floating structures (based on DNV-OS-E302)

DEP 37.81.21.31-Gen. Permanent Mooring System Wire Rope, Sockets, Pins and Connectors for Deepwater Floating Structures (Based on DNV-OS-E304)

DEP 37.81.21.32-Gen. Surface preparation, materials, application, and quality control testing of aluminum-ceramic basecoat with resin-bonded fluorocarbon topcoat coating systems for deepwater offshore equipment

DEP 37.81.21.33-Gen. Surface preparation, materials, application, and quality control testing of low friction corrosion resistant fluorocarbon coating systems for deepwater offshore equipment

DEP 37.81.21.34-Gen. Thermal-sprayed ceramic coating requirements

DEP 37.81.21.35-Gen. General requirements for top tensioned riser tendon and mooring equipment for deepwater floating production systems

DEP 37.81.41.40-Gen. 9-5/8 inch riser threaded connector, gauging specification/quality plan



DEP 37.81.41.43-Gen. 14 inch riser threaded connector, gauging specification/quality plan

DEP 37.90.10.32-Gen. Dynamically positioned (DP) vessels for construction, drilling/completions/well intervention activities – selection and operation

DEP 37.91.10.10-Gen. Single point mooring (SPM) systems

DEP 37.91.10.11-Gen. Mobile mooring systems (based on API RP 2SK, API RP 2SM and API RP 2I)

DEP 37.91.10.30-Gen. Mooring and berthing systems, including fenders, quick release hooks, and docking aid systems

DEP 37.91.20.30-Gen. Oil loading and discharge hoses for offshore mooring installations (amendments/supplements to OCIMF guide to manufacturing and purchasing hoses for offshore moorings (GMPHOM 2009))



DEP 37.92.10.30-Gen. Offshore pedestal-mounted cranes (amendments/supplements to API Spec 2C)

DEP 39.40.20.32-Gen. Elastomeric flexible elements for use in TLP tendons

DEP 40.10.01.12-Gen. Polyester rope for deepwater mooring (amendments/supplements to abs guidance notes on the application of fiber rope for offshore mooring)

DEP 60.00.10.13-Gen. Mobile crane foundation assessment

DEP 80.00.10.11-Gen. Layout of onshore facilities

DEP 80.00.10.12-Gen. Layout of offshore facilities

DEP 80.80.00.10-Gen. Lifeboats and rescue boats (amendments/supplements to SOLAS, LSA and DNV-OS-E406)

DEP 80.80.00.14-Gen. Offshore facilities life-saving appliance requirements

5. ELECTRICAL

DEP 33.64.10.10-Gen. Electrical engineering design

DEP 33.64.10.12-Gen. Electrical supply and generation - design and operation

DEP 33.64.10.17-Gen. Application of protective functions for electrical systems

DEP 33.64.10.32-Gen. Electrical network monitoring and control system for industrial networks

DEP 33.64.10.33-Gen. Electromagnetic compatibility (EMC)

DEP 33.64.20.10-Gen. Electrical engineering design for North American application

DEP 33.64.30.30-Gen. Electrical packaged equipment requirements for North American application

DEP 33.65.11.31-Gen. Synchronous AC machines (amendments/supplements to IEC 60034-1 and IEC 60034-14)

DEP 33.65.11.32-Gen. Packaged alternating current generator sets

DEP 33.65.11.34-Gen. Synchronous AC machines for North American application (amendments/supplements to API 546)

DEP 33.65.11.35-Gen. Packaged unit AC generator sets for North American applications

DEP 33.65.40.31-Gen. Power transformers (amendments/supplements to IEC 60076-1 and IEC 60076-11)

DEP 33.65.40.32-Gen. Liquid-immersed transformers for North American application

DEP 33.65.50.31-Gen. Static DC uninterruptible power supply (DC UPS) units

DEP 33.65.50.32-Gen. Static A.C. uninterruptible power supply unit (static A.C. UPS unit)

DEP 33.65.50.33-Gen. Design and fabrication of AC uninterruptible power supplies for North American applications

DEP 33.65.50.34-Gen. Design and fabrication of DC uninterruptible power supplies for North American applications

DEP 33.65.60.30-Gen. Solar power systems

DEP 33.66.05.31-Gen. Electrical machines - Cage-induction types (amendments/supplements to IEC 60034-1 and IEC 60034-14)

DEP 33.66.05.32-Gen. AC electrical adjustable speed drive systems - Rated 375 KW and larger for North American application (amendments to IEEE STD 1566:2005)

DEP 33.66.05.33-Gen. A.C. electrical variable speed drive systems

DEP 33.66.05.35-Gen. LV induction motors for North American application (amendments/supplements to IEEE Std 841)

DEP 33.66.05.36-Gen. MV induction motors for North American application (amendments/supplements to API 541)

DEP 33.66.05.37-Gen. General-purpose form-wound squirrel cage induction motors – 250 horsepower and larger for North American application (amendments/supplements to API 547)

DEP 33.66.05.38-Gen. Design and fabrication of MV motor control centres for North American application (amendments to UL 347/CAS C22.2 No. 253-09)

DEP 33.66.05.39-Gen. Design and fabrication of low voltage motor control centres for North American application (amendments to UL 845/CSA C22.2 NO. 254-05)

DEP 33.67.01.31-Gen. Low voltage switchgear and controlgear assemblies (amendments/supplements to IEC 61439)



DEP 33.67.01.32-Gen. Design and fabrication of LV switchgear for North American applications

DEP 33.67.40.30-Gen. Design and fabrication of MV switchgear for North American applications

DEP 33.67.40.31-Gen. Design and fabrication of MV metal-enclosed interrupter switchgear for North American applications (amendments/supplements to IEEE C37.20.3:2006)

DEP 33.67.51.31-Gen. High-voltage switchgear and controlgear assemblies for rated voltages between 1 kV and 52 kV (amendments/supplements to IEC 62271-200)

DEP 33.68.30.31-Gen. Electrical heating system for frost heave prevention of refrigerated hydrocarbon storage tanks

DEP 33.68.30.32-Gen. Electrical trace heating

DEP 33.68.30.33-Gen. Electrical process heaters

DEP 33.68.30.34-Gen. Electrical trace heating for North American application

DEP 33.80.00.30-Gen. Navigational aids for fixed offshore structures

DEP 34.17.10.37-Gen. Design and fabrication of modular electrical power centers for North American application

DEP 63.10.08.11-Gen. Field commissioning of electrical installations and equipment

DEP 63.10.08.14-Gen. Field commissioning and testing of electrical installations and equipment for North American application

RMP 63.10.08.50-Gen. Maintenance of electrical installations and equipment

DEP 63.20.08.10-Gen. Electrical installation for North American application

DEP 80.00.10.13-Gen. Area classification and electrical equipment spacing for North American application

DEP 80.64.10.10-Gen. Electrical safety rules

DEP 80.64.10.11-Gen. Static electricity

6. HEALTH

DEP 30.00.60.10-Gen. Human factors engineering in projects

DEP 30.00.60.13-Gen. Human factors engineering – valves

DEP 30.00.60.14-Gen. Human factors engineering - application during construction

DEP 30.00.60.15-Gen. Human factors engineering - control room design

DEP 30.00.60.16-Gen. Human factors engineering - Human machine interface design for situation awareness

DEP 30.00.60.18-Gen. Human factors engineering - design and procurement of skid-packaged units

DEP 30.00.60.19-Gen. Human factors engineering – Design for process safety critical tasks

DEP 30.00.60.20-Gen. Human factors engineering – Workspace design

DEP 30.00.60.21-Gen. Human factors engineering – labelling of facilities, equipment and piping

7. MECHANICAL, MATERIALS & INTEGRITY

DEP 02.00.00.10-Gen. Preparation of technical drawings

DEP 30.10.02.11-Gen. Metallic materials - selected standards

DEP 30.10.02.13-Gen. Non-metallic materials - selection and application

DEP 30.10.02.14-Gen. Carbon steel corrosion engineering manual for upstream facilities

DEP 30.10.02.15-Gen. Materials for use in H2S-containing environments in oil and gas production (amendments and supplements to ISO 15156:2009)

DEP 30.10.02.16-Gen. Evaluation of pipeline and pressure vessel steels for resistance to hydrogen-induced cracking (amendments/supplements to NACE TM0284)

DEP 30.10.02.17-Gen. Wet H2S requirements for downstream pressure vessels and piping

DEP 30.10.02.31-Gen. Metallic materials - prevention of brittle fracture in new assets



DEP 30.10.02.32-Gen. Materials and fabrication requirements for 2¼Cr-1Mo, 2¼Cr-1Mo-¼V, 3Cr-1Mo & 3Cr-1Mo-¼V heavy wall pressure vessels (amendments/supplements to API RP 934-A)

DEP 30.10.02.34-Gen. Casting requirements for pressure retaining and rotating equipment components

DEP 30.10.02.35-Gen. Technical requirements for the supply of components in 6Mo austenitic, 22Cr duplex and 25Cr super duplex stainless steel

DEP 30.10.02.36-Gen. Materials and fabrication requirements for 1¼Cr-½Mo pressure vessels (amendments/supplements to API RP 934-C and API RP 934-E)

RMP 30.10.02.50-Gen. Metallic materials - Prevention of brittle fracture in existing assets

DEP 30.10.05.11-Gen. Plant model construction and review

DEP 30.10.60.18-Gen. Welding of metals (amendments/supplements to API RP 582)

DEP 30.10.60.30-Gen. Welding on pressurized pipes (amendments/supplements to API Standard 1104)

DEP 30.10.60.31-Gen. Oxidation of stainless steel weldments

DEP 30.10.73.10-Gen. Cathodic protection

DEP 30.10.73.31-Gen. Design of cathodic protection systems for onshore buried pipelines and on-plot piping (amendments/supplements to ISO 15589-1:2003)

DEP 30.10.73.32-Gen. Cathodic Protection Systems for Subsea Pipelines and Hardware (Amendments/Supplements to ANSI/NACE SP0607-2007/ISO 15589-2)

DEP 30.10.73.33-Gen. Installation and commissioning of onshore cathodic protection systems

DEP 30.48.00.31-Gen. Protective coatings for onshore and offshore facilities

DEP 30.48.00.32-Gen. Coating of fasteners

DEP 30.48.40.31-Gen. Thermal spray coatings of aluminium

DEP 30.48.60.10-Gen. Rubber-lined process equipment

DEP 30.48.60.13-Gen. Design and installation of chemical-resistant brick lining for process equipment (based on EN 14879-Parts 1, 4 and 6)

DEP 30.55.03.30-Gen. Validation of NDE for fabrication inspection

DEP 31.01.10.10-Gen. Chemical injection systems for upstream production facilities

DEP 31.01.10.11-Gen. Corrosion prevention and control of water injection systems (EP)

DEP 31.10.00.10-Gen. Positive material identification (PMI) program

DEP 31.10.00.31-Gen. Noise control (amendments/supplements to ISO 15664)

DEP 31.10.03.10-Gen. Symbols and identification system - Mechanical

DEP 31.22.00.30-Gen. Equipment criticality in pressure vessel design

DEP 31.22.00.31-Gen. Unfired pressure vessels

DEP 31.22.10.35-Gen. Manufacturing report for pressure vessels

DEP 31.22.30.14-Gen. Glass-fibre reinforced plastic vessels

DEP 31.24.40.12-Gen. Fabric expansion joints (endorsement of RAL-GZ 719)

DEP 31.24.40.31-Gen. Materials for high-temperature conversion process furnace parts

DEP 31.24.49.31-Gen. Fabrication of heater piping

DEP 31.36.10.30-Gen. Hydraulic systems for the operation of on/off valves in protective functions

DEP 31.38.01.10-Gen. Piping class - Basis of design

DEP 31.38.01.11-Gen. Piping - General requirements

DEP 31.38.01.12-Gen. Piping classes - Refining and chemicals

DEP 31.38.01.13-Gen. Compilation of bill of material for piping isometrics

DEP 31.38.01.15-Gen. Piping classes - Exploration and production

DEP 31.38.01.19-Gen. Water injection in Downstream hydroprocessing units for corrosion control

DEP 31.38.01.20-Gen. Design of injection points and injection systems for Downstream processing applications

DEP 31.38.01.21-Gen. Compilation of a specification for piping systems

DEP 31.38.01.29-Gen. Pipe supports



DEP 31.38.01.31-Gen. Shop and field fabrication of piping

DEP 31.38.30.11-Gen. Protective heating of piping systems (non-electrical)

RMP 31.40.00.50-Gen. Corrosion mitigation strategy for wet sour gas carbon steel pipelines

DEP 31.40.10.19-Gen. Glass-fibre reinforced plastic pipeline and piping systems

DEP 31.40.10.20-Gen. Spoolable f bre-reinforced plastic pipes

RMP 31.40.10.50-Gen. Glass-fibre reinforced plastic pipeline and piping systems - Maintenance and repair

DEP 31.40.20.32-Gen. CRA clad and CRA-lined steel pipe (amendments/supplements to API Spec 5LD)

DEP 31.40.20.33-Gen. Linepipe induction bends (amendments/supplements to ISO 15590-1)

DEP 31.40.20.34-Gen. Welded and seamless duplex and super duplex stainless steel line pipe (amendments/supplements to API Spec 5LC)

DEP 31.40.20.36-Gen. Weldable martensitic stainless steel line pipe for use in oil and gas operations (amendments/supplements to API SPEC 5LC)

DEP 31.40.20.37-Gen. Line pipe for critical service (amendments/supplements to ISO 3183:2012 and API SPEC 5L 45th edition)

DEP 31.40.20.39-Gen. High density polyethylene pipelines and piping systems for oilfield applications

DEP 31.40.21.30-Gen. Pipeline fittings (amendments/supplements to ISO 15590-2) and low temperature process piping fittings

DEP 31.40.21.34-Gen. Carbon and low alloy steel pipeline flanges for use in oil and gas operations (amendments/supplements to ISO 15590-3) and low temperature carbon steel flanges for piping (amendments/supplements to ASTM A350 GR LF2)

DEP 31.40.30.31-Gen. External polyethylene and polypropylene coating for line pipe (amendments/supplements to ISO/DIS 21809-1:2009)

DEP 31.40.30.32-Gen. External fusion-bonded epoxy powder coating for line pipe (amendments/supplements to ISO 21809-2:2007)

DEP 31.40.30.33-Gen. Bituminous enamel coating of steel linepipe

DEP 31.40.30.34-Gen. Thermoplastic lined pipelines for onshore use

DEP 31.40.30.35-Gen. Internal coating of line pipe for non-corrosive gas transmission service (amendments/supplements to ISO 15741)

DEP 31.40.30.36-Gen. Elastomer coatings and Monel sheathing for offshore riser protection

DEP 31.40.30.37-Gen. External field joint and rehabilitation coating systems for line pipe (amendments/supplements to ISO 21809-3:2008)

DEP 31.40.30.39-Gen. Internal fusion-bonded epoxy powder coating for water injection line pipe

DEP 31.46.00.31-Gen. Acoustic insulation for piping (amendments/supplements to ISO 15665)

DEP 31.76.10.10-Gen. Heating, ventilation and air conditioning for plant buildings

DEP 34.51.01.31-Gen. Vertical steel storage tanks – Selection design and construction (amendments/supplements to EN 14015)

DEP 34.51.01.33-Gen. Aboveground vertical storage tanks (amendments/supplements to API Standard 650)

DEP 34.51.11.30-Gen. Mounded horizontal cylindrical vessels for pressurised storage of LPG at ambient temperatures (amendments/supplements to EEMUA 190)

DEP 34.51.90.10-Gen. Demolition of storage tanks (endorsement of EEMUA 154)

DEP 37.19.30.30-Gen. Cathodic protection systems for fixed offshore steel structures (amendments/supplements to NACE SP0176-2007)

DEP 37.76.10.10-Gen. HVAC for offshore installations (amendments/supplements to ISO 15138)

DEP 37.81.20.31-Gen. Galvanic anodes for marine structures and pipelines – Specification and qualification – Modifications to ISO 15589-2

DEP 37.81.20.40-Gen. Impressed current laboratory testing of aluminum alloy anodes (amendments/supplements to NACE Std TM0190-2006)

DEP 37.81.40.30-Gen. Syntactic foam insulation for flowlines

DEP 37.81.40.34-Gen. Insulation for pipe-in-pipe (PIP) flowlines

DEP 37.81.40.40-Gen. External Monel clad riser pipe

DEP 37.81.40.41-Gen. Hyperbaric welding of pipelines (amendments/supplements to ISO 13847)



DEP 37.81.41.36-Gen. Deepwater syntactic foam insulation for subsea structures

DEP 37.81.41.37-Gen. Qualification of insulation for deepwater applications

DEP 39.01.10.11-Gen. Selection of materials for life cycle performance (upstream facilities) - Materials selection process

DEP 39.01.10.12-Gen. Selection of materials for life cycle performance (Upstream facilities) - Equipment

DEP 39.01.10.13-Gen. Selection of materials for carbon capture and sequestration systems

DEP 39.01.10.30-Gen. Specification for nickel base alloy 625 plus (UNS N07716) and alloy 725 (UNS N07725) for oil and gas drilling and production equipment

DEP 39.01.10.32-Gen. Specification of nickel base alloy 718 (UNS N07718) for oil and gas drilling and production equipment (amendments/supplements to API Standard 6A718)

DEP 44.24.32.31-Gen. Classification of unshaped refractory lining materials

DEP 44.24.90.31-Gen. Refractory bricks and shapes

DEP 44.24.90.32-Gen. Classification of refractory bricks and shapes

DEP 44.24.90.33-Gen. Specification for sampling and testing of refractory bricks and shapes

DEP 44.24.90.34-Gen. Classification, specification and testing for ancillary materials for refractory brick construction

DEP 44.24.90.35-Gen. Specification and quality control for precast or specialty cast refractory baffle wall tile (shapes)

DEP 61.10.08.11-Gen. Field inspection prior to commissioning of mechanical equipment

DEP 61.38.10.10-Gen. Shop and field fabrication of orifice meter runs

DEP 61.40.20.30-Gen. Welding of pipelines and related facilities (amendments/supplements to ISO 13847:2000)

DEP 61.40.20.31-Gen. Field welding of duplex and super duplex stainless steel pipelines (amendments/supplements to API 1104)

DEP 61.40.20.36-Gen. Welding of CRA-CLAD or CRA-LINED pipe materials (amendments/supplements to API 1104:20th edition)

DEP 64.24.32.11-Gen. Refractory linings for sulphur recovery units (Claus and SCOT)

DEP 64.24.32.12-Gen. Refractory lining for fluidized catalytic cracking unit (FCCU)

DEP 64.24.32.31-Gen. Construction details for refractory brick and shape construction

DEP 64.24.32.33-Gen. Guidelines for curing, drying and firing of unshaped refractory lining materials

DEP 64.24.32.34-Gen. Refractory contractor selection and applicator qualification for installation of unshaped refractory lining materials

DEP 64.24.32.35-Gen. Construction design details of unshaped refractory materials

DEP 70.10.70.11-Gen. Preservation of new and old equipment standing idle

DEP 74.00.10.10-Gen. Shop and field pressure testing of piping systems

DEP 80.36.00.30-Gen. Relief devices - Selection, sizing and specification

DEP 80.45.10.10-Gen. Design of pressure relief, flare and vent systems

DEP 80.46.30.11-Gen. Interlocking systems for pressure relief valves

DEP 44.24.32.30-Gen. Unshaped refractory materials for monolithic refractory linings

DEP 44.24.32.32-Gen. Specification for sampling and testing of unshaped refractory lining materials

DEP 44.24.32.33-Gen. Specification for anchoring systems of unshaped refractory lining materials

RMP 70.10.70.50-Gen. Preservation of new and old equipment standing idle

RMP 70.51.10.50-Gen. Field inspection, maintenance and repair of vertical steel storage tanks (amendments/supplements to API 653 and EEMUA159)

8. OPERATIONS EXCELLENCE & ASSET MANAGEMENT DEP 01.00.09.10-Gen. Operational tagging requirements

DEP 70.08.10.11-Gen. Mechanical and electrical maintenance equipment and tools

DEP 70.10.90.11-Gen. Spare parts

DEP 82.00.10.30-Gen. Engineering information specification (EIS)



9. PETROLEUM ENGINEERING

DEP 25.80.10.10-Gen. Formation pore pressure, fracture gradient (PP/FG) and borehole stability prediction for exploration, appraisal and development wells, well entries, and abandonments

DEP 25.80.10.11-Gen. Formation tops, fault intersections, and fluid fill prediction for exploration, appraisal, and development wells

DEP 25.80.10.12-Gen. Prepare and maintain data in support of well emergencies - new wells and new activities on existing wells

DEP 25.80.10.13-Gen. Geohazards assessment for offshore exploration, appraisal and development operations

DEP 25.80.10.15-Gen. Design a logging program

DEP 25.80.10.16-Gen. Compaction and subsidence prediction

DEP 25.80.10.18-Gen. Hydrogen sulphide prediction for produced fluids from new and existing wells in oil and gas fields

DEP 25.80.10.19-Gen. Sand failure assessment for wells to be completed and produced

DEP 25.80.10.20-Gen. Planning and design of geophysical surveys

DEP 25.80.10.21-Gen. Well stimulation

DEP 25.80.10.22-Gen. Top-seal integrity assessment for primary recovery, waterflood, EOR and CO2 storage

10. PIPELINES, FLOW ASSURANCE SYSTEMS & SUBSEA

DEP 31.27.00.20-Gen. Design and supply of bulk solids bins and hoppers

DEP 31.27.00.21-Gen. Vibrating fluid bed drier/cooler systems

DEP 31.27.00.22-Gen. Enclosed drag conveyors

DEP 31.27.00.23-Gen. General purpose screw conveyors

DEP 31.27.00.24-Gen. Loss-in-weight feeders

DEP 31.27.00.25-Gen. Pressure Process Filters and Systems - Technology Selection, Design and Manufacture

DEP 31.27.00.26-Gen. Trough belt conveyors

DEP 31.27.00.27-Gen. Dilute phase pneumatic conveying systems

DEP 31.27.00.28-Gen. Filter presses technology selection, design and manufacture

DEP 31.27.00.29-Gen. Vacuum belt filter selection, design and manufacture

DEP 31.27.00.30-Gen. Rotary drum vacuum filter selection, design and manufacture

DEP 31.27.00.31-Gen. Decanter centrifuge selection, design and manufacture

DEP 31.27.00.32-Gen. General purpose baghouse dust collectors selection, design and manufacture

DEP 31.36.00.30-Gen. Pipeline transportation systems - pipeline valves (amendments/supplements to ISO 14313)

DEP 31.38.60.10-Gen. Hot-tapping on pipelines, piping and equipment

DEP 31.40.00.10-Gen. Pipeline engineering (amendments/supplements to ISO 13623:2009)

DEP 31.40.00.11-Gen. Pipeline and subsea integrity - Design and construction

RMP 31.40.00.51-Gen Pipeline integrity

DEP 31.40.10.10-Gen. Riser design

DEP 31.40.10.12-Gen. Design of multiple-pipe slug catchers

DEP 31.40.10.13-Gen. Design of pipeline pig trap systems

DEP 31.40.10.15-Gen. Analysis of spans for submerged pipelines

DEP 31.40.10.16-Gen. Upheaval buckling of pipelines

DEP 31.40.10.17-Gen. Pipeline/trawlgear interaction

DEP 31.40.10.18-Gen. Pipeline engineering - Reliability-based limit states methods (amendments/supplements to ISO 16708)



DEP 31.40.11.32-Gen. Pipelay survey, positioning and as-built reportings for offshore pipelines

DEP 31.40.21.31-Gen. Pipeline isolating joints (amendments/supplements to ISO 15590-2:2003)

DEP 31.40.21.33-Gen. Pig signallers - intrusive type

DEP 31.40.21.37-Gen. Corrosion resistant alloy overlay subsea pipe and fittings excluding line pipe

DEP 31.40.30.30-Gen. Concrete coating of linepipe (amendments/supplements to ISO 21809-5)

DEP 31.40.40.38-Gen. Hydrostatic pressure testing of new pipelines

DEP 31.40.50.30-Gen. Precommissioning of pipelines

DEP 31.40.60.11-Gen. Pipeline leak detection

RMP 31.40.60.50-Gen. Pipeline repairs

DEP 37.80.00.30-Gen. Subsea production systems

DEP 37.80.00.33-Gen. Design and operation of subsea production control systems (amendments/supplements to ISO 13628-6)

DEP 37.80.00.35-Gen. Subsea pipeline valves (amendments/supplements to ISO 14723)

DEP 37.80.00.36-Gen. Deepwater subsea vertical tree systems (amendments/supplements to ISO 13628-4/API 17D)

DEP 37.80.00.38-Gen. Deepwater jumper design, measurement, fabrication and testing

DEP 37.80.02.31-Gen. Seamless super duplex tubing manufacturing specification for umbilicals and subsea distr bution hardware

DEP 37.80.02.32-Gen. Seam Welded Super Duplex Tubing Manufacturing Specification for Umbilicals and Subsea Distribution Hardware

DEP 37.80.02.33-Gen. Zinc clad duplex tubing manufacturing specification

DEP 37.80.02.35-Gen. Medium voltage, 6kV (Um = 7.2kV) to 30kV (Um = 36kV), power conductors for deepwater umbilicals

DEP 37.80.02.36-Gen. Deepwater umbilical manufacturing (amendments/supplements to ISO 13628-5:2009)

DEP 37.80.02.37-Gen. Deepwater subsea controls, power, and chemical distribution manufacturing specification

DEP 37.80.03.30-Gen. Umbilical transportation and installation (amendments/supplements to ISO 13628-5:2009)

DEP 37.80.03.31-Gen. Deepwater subsea distr bution hardware installation

DEP 37.80.10.30-Gen. Deepwater subsea completion/workover systems (amendments/supplements to ISO 13628-7)

DEP 37.81.10.15-Gen. Pipe-soil interaction on a normally consolidated clay seabed

DEP 37.81.40.31-Gen. Welding of deepwater pipelines, flowlines and steel catenary risers (amendments/supplements to API 1104)

DEP 37.81.40.32-Gen. Automated ultrasonic inspection (AUT) of girth welds for carbon steel and CRA lined pipelines, flowlines and catenary risers

DEP 37.81.40.35-Gen. Deepwater collet type connector systems

DEP 37.81.40.38-Gen. Deepwater subsea manifold system (amendments/supplements to ISO 13628-15/API RP 17P)

DEP 37.81.41.30-Gen. Onshore fabrication of deepwater pipelines, flowlines, risers and their appurtenances

DEP 37.81.41.33-Gen. Offshore construction specification for deepwater pipelines, flowlines and risers

DEP 37.81.41.35-Gen. Offshore pipeline and umbilical/cable crossings

DEP 37.81.42.30-Gen. Unbonded flexible pipe for offshore applications (amendments/supplements to ISO 13628-2 & ISO 13628-11)

DEP 37.81.42.31-Gen. Deepwater pipeline end terminations and midline sleds

DEP 37.81.42.34-Gen. ROV operations for work-class vehicles

DEP 37.81.42.35-Gen. Qualification of girthweld inspection with automated ultrasonic inspection (AUT) systems



11. PROCESS AUTOMATION, CONTROL, AND OPTIMIZATION

DEP 31.40.70.30-Gen. Quarter-turn actuators for on/off valves

DEP 32.00.00.12-Gen. Fiscal and sales allocation models for Upstream production systems

DEP 32.01.20.12-Gen. Process Control Domain – Enterprise industrial automation information technology and security

DEP 32.01.23.17-Gen. Process control domain - Security requirements for suppliers

DEP 32.01.40.31-Gen. Requirements for real time production operations and production critical real time data

RMP 32.01.20.50-Gen. Process Control Domain – Enterprise industrial automation information technology and security

DEP 32.10.03.10-Gen. Instrumentation symbols and identification on process engineering flow schemes

DEP 32.30.20.11-Gen. Fire, gas and smoke detection systems

DEP 32.30.20.13-Gen. FOUNDATIONä Fieldbus - Design and configuration

DEP 32.30.20.14-Gen. Instrument asset management

DEP 32.30.20.15-Gen. DCS basic application standards

DEP 32.30.20.16-Gen. Baselayer control applications

DEP 32.30.20.17-Gen. Integration of motor controls into BPCs

DEP 32.30.20.18-Gen. Real-time optimization project standards

RMP 32.30.20.50-Gen. Fire, gas and smoke detection systems

DEP 32.31.00.32-Gen. Instruments for measurement and control

DEP 32.31.00.34-Gen. Instrumentation documents and drawings

DEP 32.31.00.35-Gen. Smartplant instrumentation (SPI) - Project execution

DEP 32.31.09.31-Gen. Instrumentation for equipment packages

DEP 32.31.50.10-Gen. On-line process analysers

DEP 32.31.50.13-Gen. Analyser housing

DEP 32.32.00.11-Gen. Custody transfer measurement systems for liquids

DEP 32.32.00.12-Gen. Custody transfer measurement systems for gases and vapours

DEP 32.32.00.13-Gen. Flow rate measurement in wet gas environments by means of Venturi tubes and tracer dilution technology

DEP 32.36.01.17-Gen. Control valves - Selection, sizing, and specification

DEP 32.37.10.11-Gen. Installation of on-line instruments

DEP 32.37.20.10-Gen. Instrument signal lines

DEP 32.45.10.10-Gen. Instrumentation of depressuring systems

RMP 32.45.10.50-Gen. Instrumentation of depressuring systems

DEP 32.80.10.10-Gen. Instrumented protective functions (IPF)

DEP 32.80.10.14-Gen. Alarm management

RMP 32.80.10.50-Gen. The operation, testing and maintenance of instrumented protective functions (IPF)

DEP 62.10.08.11-Gen. Inspection and functional testing of instruments

12. PROCESS ENGINEERING

DEP 01.00.01.30-Gen. Definition of temperature, pressure and toxicity levels

DEP 01.00.02.11-Gen. Preparation of process flow schemes and process engineering flow schemes

DEP 01.00.02.12-Gen. Preparation of Safeguarding Memoranda and Process Safeguarding Flow Schemes

DEP 10.02.51.11-Gen. Steam injection systems for safeguarding thermal cracking units

DEP 20.04.10.10-Gen. Glycol-type gas dehydration systems



DEP 30.06.10.11-Gen. Equipment in LPG processing installations

DEP 30.06.10.12-Gen. Pressurised bulk LPG storage installations at processing facilities

DEP 30.06.10.13-Gen. LPG bu k road, rail and pipeline transportation

DEP 30.06.10.14-Gen. Cylinder filling plants and bu k transfer facilities for depots and filling plants

DEP 30.06.10.16-Gen. Pressurised bulk storage installations for LPG - at depots, filling plants and large bulk customers

DEP 30.06.10.18-Gen. Pressurised bulk storage installations for LPG - at small customer premises

DEP 30.06.10.20-Gen. ESD systems for loading and discharging liquefied gas carriers

DEP 30.06.10.30-Gen. LPG storage and vehicle fuelling installations at retail sites

DEP 30.06.10.31-Gen. CNG vehicle fueling installations

RMP 30.06.10.50-Gen. ESD systems for loading and discharging liquefied gas carriers - Operations and maintenance

RMP 30.06.10.51-Gen. Equipment in LPG installations- Guidelines for operation

RMP 30.06.10.52-Gen. Pressurised bulk storage installations for LPG

RMP 30.06.10.53-Gen. LPG bu k transfer and transportation

DEP 31.06.11.11-Gen. Loading facilities for bulk road vehicles

RMP 31.10.11.50-Gen. Gaseous oxygen systems - Guidelines for operation and maintenance

DEP 31.20.20.31-Gen. Internals for columns

DEP 31.22.05.11-Gen. Gas/liquid separators - Type selection and design rules

DEP 31.22.05.12-Gen. Liquid/liquid and gas/liquid/liquid separators – Type selection and design rules

DEP 31.22.50.31-Gen. Design and installation of the bottom support structure for molecular sieve units

DEP 31.27.21.10-Gen. Filters for removing particles from hydroprocessor feeds - type selection and design rules

DEP 39.01.40.30-Gen. Seawater injection facilities

13. TECHNICAL SAFETY ENGINEERING

DEP 01.00.02.13-Gen. Process engineering and safeguarding practices (PRENSAP)

DEP 34.17.10.35-Gen. Siting of onshore occupied portable buildings

DEP 34.17.10.36-Gen. Inflatable blast resistant shelters

DEP 37.01.10.10-Gen. Offshore production installations basic surface process safety systems

DEP 39.01.00.10-Gen. Onshore production installations - Basic process safety systems

DEP 80.00.00.15-Gen. Hazard and operability (HAZOP) study

DEP 80.00.10.10-Gen. Area classification (amendments/supplements to IP 15)

DEP 80.10.10.31-Gen. Breathing air and supply systems

DEP 80.45.10.11-Gen. Overpressure and underpressure – Prevention and protection

DEP 80.45.10.12-Gen. Emergency depressuring and sectionalizing

DEP 80.45.10.13-Gen. Alternative pressure relief design for assessment of existing facilities

DEP 80.47.10.12-Gen. Water-based fire protection systems for offshore facilities

DEP 80.47.10.30-Gen. Assessment of the fire safety of onshore installations

DEP 80.47.10.31-Gen. Active fire protection systems and equipment for onshore facilities

DEP 80.47.10.32-Gen. Fire-fighting agents and portable/mobile fire fighting equipment for onshore applications

DEP 80.47.10.33-Gen. Fire-fighting vehicles and fire stations

DEP 80.80.00.11-Gen. Control and mitigation of fires and explosions on offshore production installations (amendments/supplements to ISO 13702:1999)

DEP 80.80.00.12-Gen. Offshore production installations - Requirements and guidelines for emergency response (amendments/supplements to ISO 15544:2000)



DEP 80.80.00.13-Gen. Offshore production installations - Guidelines on tools and techniques for identification and assessment of hazardous events (amendments/supplements to ISO 17776)

14. PROJECT SERVICES

DEP 82.00.10.12-Gen. Life cycle costing (endorsement of ISO 15663-1)

15. QUALITY ASSURANCE

DEP 82.00.10.10-Gen. Project quality assurance

16. ROTATING EQUIPMENT

DEP 31.25.00.10-Gen. Hoisting facilities and weather protection for rotating equipment

DEP 31.29.00.10-Gen. Installation of rotating equipment (amendments/supplements to API RP 686)

DEP 31.29.00.11-Gen. Condition monitoring of rotating equipment

DEP 31.29.00.30-Gen. Oil mist lubrication systems

DEP 31.29.00.32-Gen. Special purpose gear units for petroleum, chemical and natural gas industry services (amendments/supplements to API 613)

DEP 31.29.00.33-Gen. Shaft sealing systems for centrifugal and rotary pumps (amendments/supplements to ISO 21049:2004)

DEP 31.29.00.36-Gen. Flexible couplings for mechanical power transmission - Special purpose applications (amendments/supplements to ISO 10441)

DEP 31.29.00.38-Gen. General- purpose gear units (amendments/supplements to API 677)

DEP 31.29.00.41-Gen. Gears – selection, testing and installation

DEP 31.29.02.11-Gen. Pumps - selection, testing and installation

DEP 31.29.02.30-Gen. Centrifugal pumps (amendments/supplements to ISO 13709)

DEP 31.29.02.31-Gen. Sealless centrifugal pumps (amendments/supplements to API 685)

DEP 31.29.06.30-Gen. Centrifugal submerged motor pumps and electro submersible hydraulic turbines

DEP 31.29.06.31-Gen. Seawater lift pumps

DEP 31.29.12.30-Gen. Reciprocating positive displacement pumps (amendments/supplements to API 674)

DEP 31.29.12.31-Gen. Positive displacement pumps - controlled volume (amendments/supplements to API 675)

DEP 31.29.22.11-Gen. Positive displacement pumps – Rotary (amendments/supplements to API 676)

DEP 31.29.40.10-Gen. Compressors - Selection, testing, and installation

DEP 31.29.40.30-Gen. Axial, centrifugal and expander compressors (amendments/supplements to API Std 617)

DEP 31.29.40.31-Gen. Reciprocating compressors (amendments/supplements to API 618)

DEP 31.29.40.32-Gen. Rotary-type positive displacement compressors (amendments/supplements to API 619)

DEP 31.29.40.33-Gen. Packaged, integrally geared, centrifugal plant and instrument air compressors (amendments/supplements to API 672)

DEP 31.29.40.34-Gen. Packaged reciprocating gas compressors (amendments/supplements to ISO 13631)

DEP 31.29.42.30-Gen. Liquid ring vacuum pumps and compressors (amendments/supplements to API STD 681)

DEP 31.29.47.30-Gen. Centrifugal fans (amendments/supplements to ISO 13705, Annex E)

DEP 31.29.47.31-Gen. Centrifugal fans for petroleum, chemical, and gas industry services (amendments/supplements to API 673)

DEP 31.29.47.32-Gen. Fans – Selection, testing and installation

DEP 31.29.60.10-Gen. Steam turbines - Selection, testing and installation



DEP 31.29.60.30-Gen. General-purpose steam turbines (amendments/supplements to API 611)

DEP 31.29.60.31-Gen. Special-purpose steam turbines (amendments/supplements to ISO 10437)

DEP 31.29.60.32-Gen. Lubrication, shaft-sealing and oil-control systems and auxiliaries (amendments/supplements to ISO 10438)

DEP 31.29.60.33-Gen. Lubrication, shaft-sealing and oil-control systems – selection, testing, and installation

DEP 31.29.70.11-Gen. Combustion gas turbines - Selection, testing and installation

DEP 31.29.70.31-Gen. Gas turbines for the petroleum, chemical, and gas industry services (amendments/supplements to API STD 616)

DEP 31.29.70.32-Gen. Gas turbine combustion air intake and exhaust systems

DEP 31.29.80.30-Gen. Spark ignited and compression ignited engines

DEP 31.51.10.31-Gen. Tank mixers and agitators

DEP 32.29.20.10-Gen. Safeguarding and instrumented protective functions for rotating equipment

DEP 37.29.01.10-Gen. Firewater pumps for offshore installations

17. TELECOMS

DEP 32.71.00.10-Gen. Plant telecommunication

DEP 32.71.00.11-Gen. Telecommunications standards

DEP 32.71.00.12-Gen. Telecommunications for offshore facilities

DEP 32.71.00.13-Gen. Drilling communications

DEP 32.71.00.14-Gen. Telecommunications towers and guyed masts

DEP 32.71.00.30-Gen. Structured cabling systems for telecommunications

DEP 32.71.00.31-Gen. Telecommunications transmission system

18. UTILITIES & HEAT TRANSFER

DEP 20.05.50.10-Gen. Heat transfer fluid systems

DEP 20.05.60.10-Gen. Fuel systems

DEP 20.21.00.31-Gen. Fouling margins in tubular heat exchanger design

DEP 30.05.10.30-Gen. Nitrogen/Oxygen supply and distribution systems

DEP 30.75.10.10-Gen. Steam, condensate and boiler feed water systems

DEP 30.75.10.30-Gen. Water-tube boilers

DEP 30.75.10.31-Gen. Gas turbine heat recovery steam generators

DEP 31.10.11.31-Gen. Gaseous oxygen systems

DEP 31.21.01.11-Gen. Printed circuit heat exchangers - Selection and application

DEP 31.21.01.12-Gen. Shell and tube heat exchangers; selection and application

DEP 31.21.01.13-Gen. Welded plate-bloc heat exchangers – Application, design and fabrication

DEP 31.21.01.30-Gen. Shell and tube heat exchangers (amendments/supplements to ISO 16812:2007)

DEP 31.21.01.32-Gen. Plate and frame heat exchangers (amendments/supplements to ISO 15547-1:2005)

DEP 31.21.01.33-Gen. Printed circuit heat exchangers - design and fabrication

DEP 31.21.01.34-Gen. Brazed aluminium plate-fin heat exchangers (amendments/supplements to ISO 15547-2:2005)

DEP 31.21.01.35-Gen. Steam surface condensers and auxiliaries

DEP 31.21.01.36-Gen. Heat exchangers for packaged units - Design and fabrication

DEP 31.21.01.37-Gen. Spiral plate heat exchangers (amendments/supplements to ISO 12211:2012)

DEP 31.21.01.38-Gen. Chilling systems



DEP 31.21.07.30-Gen. Hairpin-type heat exchangers (amendments/supplements to ISO 12212:2012)

DEP 31.21.70.10-Gen. Air-cooled heat exchangers; Selection and application

DEP 31.21.70.31-Gen. Air-cooled heat exchangers (amendments/supplements to ISO 13706:2005)

DEP 31.24.00.30-Gen. Fired heaters (amendments/supplements to ISO 13705)

DEP 31.24.67.10-Gen. Firetube heaters

DEP 31.27.21.30-Gen. Dry electrostatic precipitators

DEP 31.29.56.31-Gen. Steam jet vacuum ejector sets

DEP 31.37.00.11-Gen. Instrument air supply

DEP 32.24.20.44-Gen. Instrumentation control and protection for fired equipment

DEP 32.31.09.32-Gen. Heat exchanger instrumentation requirements for performance assessment

DEP 34.74.00.10-Gen. Cooling water towers - Selection, design, fabrication and erection

DEP 37.05.10.10-Gen. Design of seawater systems for offshore and onshore

DEP 37.05.10.11-Gen. Diesel oil systems

DEP 80.45.11.12-Gen. Flare details (amendments/supplements to ISO 25457)

19. WELLS ENGINEERING

NOTE: Refer to the Wells Standards Portal, These standards are not maintained by the Technical Standards Team.



PART III NUMERICAL LISTING

Number Date of Issue

Title Custodian

DEP 00.00.00.30-Gen. Sep. 2012 Procedure for global technical standards publications

Zager, Mia L GSUSI-PTE/DTST

DEP 00.00.05.05-Gen. Feb. 2013 Global technical standards index Zager, Mia L GSUSI-PTE/DTST

DEP 00.00.06.06-Gen. Feb. 2013 Standard drawings index Zager, Mia L GSUSI-PTE/DTST

DEP 00.00.07.07-Gen. Withdrawn Standard specification index

DEP 00.00.07.10-Gen. Sep. 2011 (A01)

Design class tables Zager, Mia L GSUSI-PTE/DTST

DEP 00.00.07.30-Gen. Sep. 2012 Application of a functional specification (endorsement of ISO 13879, ISO 13880 and ISO/TR 13881)

Blauvelt, Pieter N GSUSI-PTE/DTST

DEP 00.00.10.05-Gen. Feb. 2013 Standard forms index Zager, Mia L GSUSI-PTE/DTST

DEP 00.00.20.10-Gen. Feb. 2011 The use of SI quantities and units (Endorsement of ISO/IEC 80000)

Zager, Mia L GSUSI-PTE/DTST

DEP 00.30.10.05-Gen. Withdrawn Standard forms – Instrumentation binder (Standard Drawings 37.001 and 37.002)

DEP 01.00.01.30-Gen. Feb. 2012 (A01)

Definition of temperature, pressure and toxicity levels

Salisbury, Alistair P SIEP-PTP/ADF

DEP 01.00.02.11-Gen. Feb. 2011 (Sep. 2011 Circ.)

Preparation of process flow schemes and process engineering flow schemes


DEP 01.00.02.12-Gen. Feb. 2013 Preparation of Safeguarding Memoranda and Process Safeguarding Flow Schemes


DEP 01.00.02.13-Gen. Feb. 2013 Process engineering and safeguarding practices (PRENSAP)

Salter, Natalie Y GSUSI-PTE/DAPP

DEP 01.00.04.11-Gen. Withdrawn Preparation of simplified flow schemes

DEP 01.00.09.10-Gen. Feb. 2012 Operational tagging requirements Hessels, Frank J GSNL-PTE/EOEX

DEP 02.00.00.10-Gen. Feb. 2013 Preparation of technical drawings Swaine, Martin S GSUK-PTP/BDA

DEP 05.00.11.11-Gen. Withdrawn Time schedules and progress reporting for new construction projects

DEP 05.00.51.84-Gen. Withdrawn Instrument engineering data sheet

DEP 05.00.54.40-Gen. Withdrawn List of selected instrument equipment

DEP 05.00.54.80-Gen. Withdrawn General purpose sheet (A4 size)

DEP 05.00.54.83-Gen. Withdrawn General puepose sheet (A3 size)

DEP 05.00.54.88-Gen. Withdrawn Summary of instrumentation documents and drawings

DEP 05.00.54.89-Gen. Withdrawn Summary of instrumentation requisitions

DEP 05.00.54.90-Gen. Withdrawn Summary of instrumentation cables

DEP 05.00.55.12-Gen. Withdrawn Job instructions (G-5-1)


Steam injection systems for safeguarding thermal cracking units

Bowen, Chris GSNL-PTD/TRD

DEP 20.00.10.10-Gen. Withdrawn Basic data and phase behaviour methods

DEP 20.04.10.10-Gen. Jan. 2005 (Sep. 2006 Circ.) (Sep. 2008 Circ.) (Feb.2010 Circ.) (A04)

Glycol-type gas dehydration systems Clouatre, Martyn A SEPCO-UAD/T/F

DEP 20.05.50.10-Gen. Feb. 2013 Heat transfer fluid systems Paul, Debnath SEPL-PTE/PUHT




Fuel systems Paul, Debnath SEPL-PTE/PUHT

DEP 20.21.00.31-Gen. Feb. 2011 Fouling margins in tubular heat exchanger design Zoetemeijer, Len JA GSNL-PTE/EUHT

DEP 25.80.10.10-Gen. Feb. 2013 Formation pore pressure, fracture gradient (PP/FG) and borehole stability prediction for exploration, appraisal and development wells, well entries, and abandonments

Maan, Anco C SUKEP-UIE/T/DPE

DEP 25.80.10.11-Gen. Feb. 2013 Formation tops, fault intersections, and fluid fill prediction for exploration, appraisal, and development wells

Goeyenbier, Hans PS GSNL-PTU/ESSA

DEP 25.80.10.12-Gen. Feb. 2013 Prepare and maintain data in support of well emergencies - new wells and new activities on existing wells

Goeyenbier, Hans PS GSNL-PTU/ESSA

DEP 25.80.10.13-Gen. Feb. 2013 Geohazards assessment for offshore exploration, appraisal and development operations

Ansink, Ibbel GSNL-PTU/D

DEP 25.80.10.15-Gen. Feb. 2013 Design a logging program Kraaijveld, Martin A GSNL-PTU/EDDI

DEP 25.80.10.16-Gen. Feb. 2013 Compaction and subsidence prediction Kraaijveld, Martin A GSNL-PTU/EDDI

DEP 25.80.10.18-Gen. Feb. 2013 Hydrogen sulphide prediction for produced fluids from new and existing wells in oil and gas fields

Melancon, Andre R SEPCO-UAO/D/A

DEP 25.80.10.19-Gen. Feb. 2013 Sand failure assessment for wells to be completed and produced

Melancon, Andre R SEPCO-UAO/D/A

DEP 25.80.10.20-Gen. Feb. 2013 Planning and design of geophysical surveys Ansink, Ibbel GSNL-PTU/D

DEP 25.80.10.21-Gen. Feb. 2013 Well stimulation Carpenter, David E GSUSI-UIE/O/W

DEP 25.80.10.22-Gen. Feb. 2013 Top-seal integrity assessment for primary recovery, waterflood, EOR and CO2 storage

Kraaijveld, Martin A GSNL-PTU/EDDI

DEP 30.00.60.10-Gen. Feb. 2011 Human factors engineering in projects McLeod, Ron SI-SH

DEP 30.00.60.11-Gen. Withdrawn Human factors engineering - Summary of ISO standards

DEP 30.00.60.12-Gen. Withdrawn Human factors engineering - Investment justification model

DEP 30.00.60.13-Gen. Sep. 2011 Human factors engineering – Valves McLeod, Ron SI-SH

DEP 30.00.60.14-Gen. Sep. 2012 Human factors engineering - Application during construction

McLeod, Ron SI-SH

DEP 30.00.60.15-Gen. Feb. 2012 Human factors engineering - Control room design McLeod, Ron SI-SH

DEP 30.00.60.16-Gen. Feb. 2013 Human factors engineering - Human machine interface design for situation awareness

McLeod, Ron SI-SH

DEP 30.00.60.18-Gen. Sep. 2012 Human factors engineering - Design and procurement of skid-packaged units

McLeod, Ron SI-SH

DEP 30.00.60.19-Gen. Feb. 2011 Human factors engineering – Design for process safety critical tasks

McLeod, Ron SI-SH

DEP 30.00.60.20-Gen. sep-11 Human factors engineering – Workspace design McLeod, Ron SI-SH

DEP 30.00.60.21-Gen. Feb. 2012 Human factors engineering – Labelling of facilities, equipment and piping

McLeod, Ron SI-SH

DEP 30.05.10.30-Gen. Feb. 2012 Nitrogen/Oxygen supply and distribution systems Paul, Debnath SEPL-PTE/PUHT

DEP 30.06.10.10-Gen. Withdrawn Introduction and physical properties and characteristics of LPG

DEP 30.06.10.11-Gen. Feb. 2013 Equipment in LPG processing installations Oldham, Steven R GSNL-PTD/THSC

DEP 30.06.10.12-Gen. Feb. 2013 Pressurised bu k LPG storage installations at processing facilities

Oldham, Steven R GSNL-PTD/THSC

DEP 30.06.10.13-Gen. Feb. 2013 LPG bulk road, rail and pipeline transportation Oldham, Steven R GSNL-PTD/THSC

DEP 30.06.10.14-Gen. Feb. 2013 Cylinder filling plants and bulk transfer facilities for depots and filling plants


DEP 30.06.10.15-Gen. Withdrawn LPG – Cylinders and skid tanks - Consumer equipment and installations



DEP 30.06.10.16-Gen. Feb. 2013 Pressurised bu k storage installations for LPG - at depots, filling plants and large bulk customers


DEP 30.06.10.18-Gen. Feb. 2013 Pressurised bu k storage installations for LPG - at small customer premises


DEP 30.06.10.20-Gen. Feb. 2013 ESD systems for loading and discharging liquefied gas carriers

Meiring, Wouter J GSNL-PTU/LF

DEP 30.06.10.30-Gen. Feb. 2013 LPG storage and vehicle fuelling installations at retail sites


DEP 30.06.10.31-Gen. Feb. 2013 CNG vehicle fueling installations Oldham, Steven R GSNL-PTD/THSC

RMP 30.06.10.50-Gen. Sep. 2011 ESD systems for loading and discharging liquefied gas carriers – Operations and maintenance

Meiring, Wouter J GSNL-PTU/LF

RMP 30.06.10.51-Gen. Feb. 2011 Equipment in LPG installations – Guidelines for operation


RMP 30.06.10.52-Gen. Feb. 2011 Pressurised bu k storage installations for LPG Oldham, Steven R GSNL-PTD/THSC

RMP 30.06.10.53-Gen. Feb. 2011 LPG bulk transfer and transportation Oldham, Steven R GSNL-PTD/THSC

DEP 30.06.11.11-Gen. Withdrawn Pressure storage facilities for LPG (30.06.10.12)

DEP 30.10.01.10-Gen. Feb. 2013 Requisitions index Zager, Mia L GSUSI-PTE/DTST

DEP 30.10.02.11-Gen. Feb. 2012 (A01)

Metallic materials - selected standards Busch, Fred JM GSNL-PTE/EMMI

DEP 30.10.02.12-Gen Withdrawn Construction materials – Metallic materials for low temperature service

DEP 30.10.02.13-Gen. Feb. 2012 Non-metallic materials - Selection and application Busch, Fred JM GSNL-PTE/EMMI

DEP 30.10.02.14-Gen. Feb. 2011 (Sep. 2011 Circ.) (Feb. 2012 Circ.)

Carbon steel corrosion engineering manual for upstream facilities

McFarland, Sam GSNL-PTE/EMMI

DEP 30.10.02.15-Gen. Feb. 2012 (A01)

Materials for use in H2S-containing environments in oil and gas production (amendments and supplements to ISO 15156:2009)


DEP 30.10.02.16-Gen. Sep. 2012 Evaluation of pipeline and pressure vessel steels for resistance to hydrogen-induced cracking (amendments/supplements to NACE TM0284)


DEP 30.10.02.17-Gen. Feb. 2013 Wet H2S requirements for downstream pressure vessels and piping

Akkerman, Marko J GSNL-PTE/EMMI

DEP 30.10.02.31-Gen. Feb. 2013 Metallic materials - prevention of brittle fracture in new assets

Raghu, Damodaran GSUSI-PTE/AMMI

DEP 30.10.02.32-Gen. Feb. 2011 (Feb. 2012 Circ.)

Materials and fabrication requirements for 2¼Cr-1Mo, 2¼Cr-1Mo-¼V, 3Cr-1Mo & 3Cr-1Mo-¼V heavy wall pressure vessels (amendments/supplements to API RP 934-A)

Yuen, Simon SCAI-PTE/AMMI

DEP 30.10.02.34-Gen. Feb. 2013 Casting requirements for pressure retaining and rotating equipment components


DEP 30.10.02.35-Gen. Feb. 2013 Technical requirements for the supply of components in 6Mo austenitic, 22Cr duplex and 25Cr super duplex stainless steel

Paterson, Steve J SUKEP-UIE/P/SDD

DEP 30.10.02.36-Gen. Feb. 2013 Materials and fabrication requirements for 1¼Cr-½Mo pressure vessels (amendments/supplements to API RP 934-C and API RP 934-E)


RMP 30.10.02.50-Gen. Feb. 2011 Metallic materials - Prevention of brittle fracture in existing assets

Mead, Hearl E GSUSI-PTE/AMMI

DEP 30.10.05.11-Gen. Feb. 2012 Plant model construction and review Kruijer, Alfred A GSNL-PTE/EMMI

DEP 30.10.40.11-Gen. Withdrawn Jointing material

DEP 30.10.60.10-Gen. Withdrawn Welding

DEP 30.10.60.11-Gen. Withdrawn Standard welding terms and definitions

DEP 30.10.60.12-Gen. Withdrawn Arc welding, cutting and gouging



DEP 30.10.60.13-Gen. Withdrawn Gas welding, cutting and gouging

DEP 30.10.60.18-Gen. Feb. 2012 (A01)

Welding of metals (amendments/supplements to API RP 582)


DEP 30.10.60.19-Gen. Withdrawn Welding tubular goods, pressure vessels and storage tanks

DEP 30.10.60.21-Gen. Withdrawn Testing of filler metals for welding

DEP 30.10.60.22-Gen. Withdrawn Welding and inspection requirements for equipment not covered by recognized standards and/or codes


Welding on pressurised pipes (amendments/supplements to API Standard 1104)

Guijt, Wim GSNL-PTE/EPFA

DEP 30.10.60.31-Gen. Feb. 2013 Oxidation of stainless steel weldments Yuen, Simon SCAI-PTE/AMMI

DEP 30.10.73.10-Gen. Feb. 2013 Cathodic protection Whitworth, Jeff M SOPUS-DSD/924

DEP 30.10.73.31-Gen. Feb. 2013 Design of cathodic protection systems for onshore buried pipelines and on-plot piping (amendments/supplements to ISO 15589-1:2003)

Whitworth, Jeff M SOPUS-DSD/924

DEP 30.10.73.32-Gen. Sep. 2011 Cathodic protection systems for Subsea pipelines and Hardware (amendments/supplements to ANSI/NACE SP0607-2007/ISO 15589-2)


DEP 30.10.73.33-Gen. Sep. 2011 Installation and commissioning of onshore cathodic protection systems


DEP 30.46.00.31-Gen. Sep. 2011 (Feb. 2012 Circ.; A02)

Thermal insulation Kruijsen, Ton ATJJM GSNL-PTE/ECSO

DEP 30.46.00.32-Gen. Withdrawn Thermal insulation for cold and dual-temperature services ( Replaced by 30.46.00.31)

DEP 30.48.00.10-Gen. Withdrawn Painting and coating (Replaced by 30.48.00.31, 70.48.10.10)

DEP 30.48.00.31-Gen. Feb. 2013 Protective coatings for onshore and offshore facilities

Gomatham, Venkateswaraswamy PTIN-PTE/PMMI

DEP 30.48.00.32-Gen. Feb. 2012 Coating of fasteners Kopp, Frans SIEP-PTP/ADS

DEP 30.48.00.34-Gen. Feb. 2013 Phosphate-conversion coatings for marine equipment

Morrison, Denby G SIEP-PTP/ADF

DEP 30.48.30.31-Gen. Sep. 2012 Cement lining of pipes (based on EN 10298) Kruijsen, Ton ATJJM GSNL-PTE/ECSO

DEP 30.48.40.31-Gen. Feb. 2012 Thermal spray coatings of aluminium van Bokhorst, Jan R GSNL-PTE/EMMI

DEP 30.48.41.31-Gen. Withdrawn Electroless nickel plating (amendments/supplements to ASTM B 733)

DEP 30.48.50.11-Gen. Withdrawn Requirements for PTFE lined piping (31.38.01.11)

DEP 30.48.50.12-Gen. Withdrawn Plastic-lined steel pipes and fittings (31.38.01.11)

DEP 30.48.50.31-Gen. Withdrawn PTFE coating of steel surfaces

DEP 30.48.50.32-Gen. Withdrawn Requirements for plastic-lined steel pipes and fittings (30.48.50.12)

DEP 30.48.60.10-Gen. Sep. 2012 Rubber-lined process equipment Gomatham, Venkateswaraswamy PTIN-PTE/PMMI

DEP 30.48.60.12-Gen. Sep. 2012 Design and installation of chemical-resistant protection systems for concrete surfaces (based on EN 14879-Parts 1, 3, 5 and 6)

Kruijsen, Ton ATJJM GSNL-PTE/ECSO

DEP 30.48.60.13-Gen. Sep. 2012 Design and installation of chemical-resistant brick lining for process equipment (based on EN 14879-Parts 1, 4 and 6)

Wolfert, Ton GSNL-PTE/EMMI

DEP 30.48.60.22-Gen. Withdrawn Installation of chemical-resistant linings for concrete structures (30.48.60.12)

DEP 30.48.60.23-Gen. Withdrawn Installation of chemical-resistant brick linings for process equipment (30.48.60.13)

DEP 30.48.60.30-Gen. Withdrawn Requirements for rubber linings for process equipment and piping (30.48.60.10)



DEP 30.48.60.33-Gen. Withdrawn Chemical-resistant (ceramic) lining materials (30.48.60.12)

DEP 30.48.60.34-Gen. Withdrawn Erosion resistant refractory linings (64.24.32.30)

DEP 30.48.70.30-Gen. Withdrawn Glass lined steel process equipment

DEP 30.55.03.30-Gen Feb. 2012 Validation of NDE for fabrication inspection Wang, David D GSUSI-PTE/AMMI

DEP 30.75.10.10-Gen Feb. 2012 Steam, condensate and boiler feed water systems Paul, Debnath SEPL-PTE/PUHT

DEP 30.75.10.30-Gen. Feb. 2013 Water-tube boilers Gouwerok, Leo JP GSNL-PTE/EUHT

DEP 30.75.10.31-Gen. Feb. 2012 Gas turbine heat recovery steam generators Gouwerok, Leo JP GSNL-PTE/EUHT


Chemical injection systems for upstream production facilities


DEP 31.01.10.11-Gen Feb. 2012 Corrosion prevention and control of water injection systems (EP)

Grimes, William D GSNL-PTE/EMMI


Loading facilities for bulk road vehicles Oldham, Steven R GSNL-PTD/THSC

DEP 31.06.11.12-Gen. Withdrawn Shell loading and discharging manuals – Loading facilities for bulk road vehicles – Part 2 – Design of top loading facilities (31.06.11.11)

DEP 31.06.11.13-Gen. Withdrawn Shell loading and discharging manuals – Loading facilities for bulk road vehicles – Part 3 – Design of bottom loading facilities (31.06.11.11)

DEP 31.06.11.14-Gen. Withdrawn Shell loading and discharging manuals – Loading facilities for bulk road vehicles – Part 4 – Ancillary equipment, services and site requirements (31.06.11.11)

DEP 31.06.12.11-Gen. Withdrawn Rail tank entu loading and discharging Part 1, Vol. 1: Selection, design and construction

DEP 31.06.12.12-Gen. Withdrawn Rail tank entu loading and discharging Part 1, Vol. 2: Selection, design and construction

DEP 31.06.12.13-Gen. Withdrawn Rail tank entu loading and discharging Part 2: Layouts, examples and drawings

DEP 31.06.15.10-Gen. Sep. 2010 Marine loading arms (amendments/ supplements to OCIMF design and construction specification for marine loading arms)

Veale, David GSNL-PTE/ECSO

DEP 31.10.00.10-Gen. Feb. 2013 Positive material identification (PMI) program Breitkreuz, David B GSUSI-PTE/AMMI

DEP 31.10.00.31-Gen. Feb. 2012 Noise control (amendments/supplements to ISO 15664)

Kruijer, Alfred A GSNL-PTE/EMMI

DEP 31.10.03.10-Gen. Feb. 2013 Symbols and identification system - Mechanical Kruijer, Alfred A GSNL-PTE/EMMI


Gaseous oxygen systems Paul, Debnath SEPL-PTE/PUHT

RMP 31.10.11.50-Gen. Feb. 2011 Gaseous oxygen systems – Guidelines for operation and maintenance

Paul, Debnath SEPL-PTE/PUHT

DEP 31.10.21.30-Gen. Withdrawn Bolt tensioning (70.08.10.11)

DEP 31.20.20.31-Gen. Feb. 2012 (A01) (A02)

Internals for columns Nooijen, Hans L GSNL-PTD/TRD

DEP 31.21.00.19-Gen. Withdrawn Guide for the specification of shell-and-tube heat exchangers (31.21.00.93)

DEP 31.21.01.11-Gen. Feb. 2012 Printed circuit heat exchangers – Selection and application

Zoetemeijer, Len JA GSNL-PTE/EUHT

DEP 31.21.01.12-Gen. Feb. 2012 (A01)

Shell and tube heat exchangers; selection and application


DEP 31.21.01.13-Gen. Feb. 2012 (A01)

Welded plate-bloc heat exchangers – Application, design and fabrication




DEP 31.21.01.30-Gen. Feb. 2013 Shell and tube heat exchangers (amendments/supplements to ISO 16812:2007)


DEP 31.21.01.31Gen. Withdrawn Selected construction materials for shell-and-tube heat exchangers

DEP 31.21.01.32-Gen. Feb. 2012 Plate and frame heat exchangers (amendments/supplements to ISO 15547-1:2005)


DEP 31.21.01.33-Gen. Feb. 2011 (Sep. 2011 Circ.) (A02)

Printed circuit heat exchangers - design and fabrication



Brazed aluminium plate-fin heat exchangers (amendments/supplements to ISO 15547-2:2005)


DEP 31.21.01.35-Gen. Feb. 2013 Steam surface condensers and auxiliaries Zoetemeijer, Len JA GSNL-PTE/EUHT

DEP 31.21.01.36-Gen. Feb. 2012 (A01)

Heat Exchangers for Packaged Units - Design and Fabrication


DEP 31.21.01.37-Gen. Feb. 2013 Spiral plate heat exchangers (amendments/supplements to ISO 12211:2012)


DEP 31.21.01.38-Gen. Feb. 2013 Chilling systems Paul, Debnath SEPL-PTE/PUHT

DEP 31.21.07.30-Gen. Feb. 2013 Hairpin-type heat exchangers (amendments/supplements to ISO 12212:2012)


DEP 31.21.20.31-Gen. Withdrawn Shell-and-tube heat exchangers with hot-dip galvanized tubes


Air-cooled heat exchangers; Selection and application


DEP 31.21.70.31-Gen. Feb. 2011 (Feb. 2012 Circ.) (A02)

Air-cooled heat exchangers (amendments/supplements to ISO 13706:2005)


DEP 31.22.00.11-Gen Withdrawn Pressure vessels

DEP 31.22.00.30-Gen. Feb. 2013 Equipment criticality in pressure vessel design Yuen, Simon SCAI-PTE/AMMI

DEP 31.22.00.31-Gen. Feb. 2013 Unfired pressure vessels Yuen, Simon SCAI-PTE/AMMI

DEP 31.22.01.31-Gen. Withdrawn Rotating disc contactors

DEP 31.22.05.11-Gen. Feb. 2012 Gas/liquid separators – Type selection and design rules

Nooijen, Hans L GSNL-PTD/TRD

DEP 31.22.05.12-Gen. Feb. 2012 Liquid/liquid and gas/liquid/liquid separators – Type selection and design rules

Nooijen, Hans L GSNL-PTD/TRD

DEP 31.22.10.31-Gen. Withdrawn Pressure vessels (amendments/supplements to BS 1515 Part 1)

DEP 31.22.10.32-Gen. Withdrawn Pressure vessels (amendments/supplements to PD 5500)

DEP 31.22.10.33-Gen. Withdrawn Tolerances for pressure vessels (31.22.10.32)

DEP 31.22.10.34-Gen. Withdrawn Pressure vessels (amendments/supplements to AS 1210)

DEP 31.22.10.35-Gen. Sep. 2012 (A01)

Manufacturing report for pressure vessels Wylie, Tom P GSUSI-PTE/AMMI

DEP 31.22.10.36-Gen. Withdrawn LPG storage vessels for aboveground storage of C3 and heavier hydrocarbons (30.06.10.12, 31.22.10.32)

DEP 31.22.11.32-Gen. Withdrawn Unfired pressure vessels (amendments/supplements to EN 13445)

DEP 31.22.20.31-Gen. Withdrawn Pressure vessels (based on ASME section VIII)

DEP 31.22.30.14-Gen. Sep. 2012 Glass-fibre reinforced plastic vessels Janssen, Frans AH GSNL-PTI/GM



DEP 31.22.30.24-Gen. Withdrawn Installation of glass-fibre reinforced epoxy vessels and equipment (31.22.30.14)

DEP 31.22.30.34-Gen. Withdrawn Glass-fibre reinforced epoxy and polyester vessels – manufacturing requirements (31.22.30.14)

DEP 31.22.31.31-Gen. Withdrawn Pressure vessels (based on Chinese code GB 150-1998)

DEP 31.22.50.31-Gen. Sep. 2012 (A01)

Design and installation of the bottom support structure for molecular sieve units

Klinkenbijl, Jeanine M GSNL-PTU/TDEX

DEP 31.22.90.30-Gen. Withdrawn Seamless steel transportable gas containers (endorsement of BS 5045-1)


Fired heaters (amendments/supplements to ISO 13705)

Gouwerok, Leo JP GSNL-PTE/EUHT

DEP 31.24.00.31-Gen. Withdrawn Calculation of heater-tube thickness (Endorsement of ISO 13704)

DEP 31.24.15.31-Gen. Withdrawn SIPM-type vertical furnaces, including waste heat boilers (31.24.00.30)

DEP 31.24.20.30-Gen. Withdrawn Control system and instrumented protective functions for fired equipment – system for a single burner furnace (S 24.024 and S24.026)

DEP 31.24.20.33-Gen. Withdrawn Control system and instrumented protective functions for fired equipment – System for an automatically started, gas fired, natural draught, multi burner furnace, safeguarded by pilot burners (S 24.033)

DEP 31.24.20.37-Gen. Withdrawn Control system and instrumented protective functions for fired equipment – System for a manually started, forced draught, multi burner furnace or boiler (S 24.021)

DEP 31.24.20.38-Gen. Withdrawn Control system and instrumented protective functions for fired equipment – System for an automatically-started, forced draught, multi-burner furnace or boiler (S 24.030 or S24.034)

DEP 31.24.20.40-Gen. Withdrawn Control system and instrumented protective functions for fired equipment – system for a tangentially gas-fired CO boiler (S 24.036)

DEP 31.24.20.42-Gen. Withdrawn Control system and instrumented protective functions for fired equipment – Systems for co-fired gas turbine waste heat recovery units

DEP 31.24.40.12-Gen. Sep. 2012 Fabric expansion joints (endorsement of RAL-GZ 719)


DEP 31.24.40.31-Gen. Feb. 2012 Materials for high-temperature conversion process furnace parts

Busch, Fred JM GSNL-PTE/EMMI

DEP 31.24.49.31-Gen. Sep. 2012 Fabrication of heater piping Yuen, Simon SCAI-PTE/AMMI

DEP 31.24.66.11-Gen. Withdrawn Mobile ignition unit for furnaces and steam boilers

DEP 31.24.66.12-Gen. Withdrawn Mobile ignition unit for LMV line burners of sulphur recovery units

DEP 31.24.67.10-Gen. Feb. 2013 Firetube heaters Gouwerok, Leo JP GSNL-PTE/EUHT

DEP 31.25.00.10-Gen. Feb. 2013 Hoisting facilities and weather protection for rotating equipment

Rijsdijk, Robert L GSNL-PTE/EREQ

DEP 31.27.00.20-Gen. Feb. 2012 Design and supply of bulk solid bins and hoppers Giles, Steve P SIEP-PTI/GF

DEP 31.27.00.21-Gen. Feb. 2012 Vibrating fluid bed drier/cooler systems Giles, Steve P SIEP-PTI/GF

DEP 31.27.00.22-Gen. Feb. 2012 Enclosed drag conveyors Giles, Steve P SIEP-PTI/GF

DEP 31.27.00.23-Gen. Feb. 2012 General purpose screw conveyors Giles, Steve P SIEP-PTI/GF

DEP 31.27.00.24-Gen. Feb. 2012 Loss-in-weight feeders Giles, Steve P SIEP-PTI/GF

DEP 31.27.00.25-Gen. Feb. 2012 (A01)

Pressure Process Filters and Systems - Technology Selection, Design and Manufacture

Giles, Steve P SIEP-PTI/GF



DEP 31.27.00.26-Gen. Sep. 2012 Trough belt conveyors Giles, Steve P SIEP-PTI/GF

DEP 31.27.00.27-Gen. Sep. 2012 (A01)

Dilute phase pneumatic conveying systems Giles, Steve P SIEP-PTI/GF

DEP 31.27.00.28-Gen. Sep. 2012 Filter presses technology selection, design and manufacture


DEP 31.27.00.29-Gen. Feb. 2013 Vacuum belt filter selection, design and manufacture Giles, Steve P SIEP-PTI/GF

DEP 31.27.00.30-Gen. Feb. 2013 Rotary drum vacuum filter selection, design and manufacture


DEP 31.27.00.31-Gen. Feb. 2013 Decanter centrifuge selection, design and manufacture


DEP 31.27.00.32-Gen. Feb. 2013 General purpose baghouse dust collectors selection, design and manufacture


DEP 31.27.21.10-Gen. Feb. 2012 (A01)

Filters for removing particles from hydroprocessor feeds - type selection and design rules

Yang, Guoqiang SIEP-PTI/GF

DEP 31.27.21.30-Gen. Feb. 2013 Dry electrostatic precipitators Gouwerok, Leo JP GSNL-PTE/EUHT

DEP 31.29.00.10-Gen. Sep. 2011 Installation of rotating equipment (amendments/supplements to API RP 686)


DEP 31.29.00.11-Gen. Feb. 2013 Condition monitoring of rotating equipment Rijsdijk, Robert L GSNL-PTE/EREQ

DEP 31.29.00.30-Gen. Feb. 2013 Oil mist lubrication systems Rijsdijk, Robert L GSNL-PTE/EREQ

DEP 31.29.00.31-Gen. Withdrawn Noise limitation (31.10.00.31)

DEP 31.29.00.32-Gen. Feb. 2012 Special purpose gear units for petroleum, chemical and gas industry services (amendments/supplements to API 613)


DEP 31.29.00.33-Gen. Feb. 2013 Shaft sealing systems for centrifugal and rotary pumps (amendments/supplements to ISO 21049:2004)


DEP 31.29.00.34-Gen. Withdrawn Dry gas seal systems for centrifugal compressors (31.29.40.10 and 31.29.60.32)

DEP 31.29.00.36-Gen. Feb. 2013 Flexible couplings for mechanical power transmission - Special purpose applications (amendments/supplements to ISO 10441)

Diehl, Robert J GSUSI-PTE/AREQ

DEP 31.29.00.38-Gen. Sep. 2011 General purpose gear units (amendments/supplements to API 677)


DEP 31.29.00.39-Gen. Withdrawn Shaft sealing systems for centrifugal and rotary pumps – Selection, testing and installation

DEP 31.29.00.41-Gen. Feb. 2012 Gears – Selection, testing and installation Rijsdijk, Robert L GSNL-PTE/EREQ

DEP 31.29.01.10-Gen. Withdrawn Pumps

DEP 31.29.02.10-Gen. Withdrawn Pumps – Centrifugal

DEP 31.29.02.11-Gen. Sep. 2012 Pumps – selection, testing and installation Rijsdijk, Robert L GSNL-PTE/EREQ

DEP 31.29.02.30-Gen. Feb. 2013 Centrifugal pumps (amendments/supplements to ISO 13709)


DEP 31.29.02.31-Gen. Feb. 2013 Sealless centrifugal pumps (amendments/supplements to API 685)


DEP 31.29.05.31-Gen. Withdrawn Vertical in-line centrifugal pumps

DEP 31.29.06.30-Gen. Feb. 2011 Centrifugal submerged motor pumps and electro-submersible hydraulic turbines


DEP 31.29.06.31-Gen. Feb. 2012 (A01) (A02)

Seawater lift pumps Rijsdijk, Robert L GSNL-PTE/EREQ

DEP 31.29.12.10-Gen. Withdrawn Pumps – Reciprocating

DEP 31.29.12.30-Gen. Feb. 2013 Reciprocating positive displacement pumps (amendments/supplements to API 674)


DEP 31.29.12.31-Gen. Feb. 2013 Positive displacement pumps - controlled volume (amendments/supplements to API 675)


DEP 31.29.22.10-Gen. Withdrawn Pumps – Rotary (Positive Displacement)



DEP 31.29.22.11-Gen. Feb. 2012 Positive displacement pumps – Rotary (amendments/supplements to API 676)


DEP 31.29.40.10-Gen. Feb. 2013 Compressors - Selection, testing, and installation Rijsdijk, Robert L GSNL-PTE/EREQ


Axial, centrifugal and expander compressors (amendments/supplements to API Std 617)



Reciprocating compressors (amendments/supplements to API 618)



Rotary-type positive displacement compressors (amendments/supplements to API 619)


DEP 31.29.40.33-Gen. Feb. 2012 Packaged, integrally geared, centrifugal plant and instrument air compressors (amendments/supplements to API 672)


DEP 31.29.40.34-Gen. Feb. 2012 (A01)

Packaged reciprocating gas compressors (amendments/supplements to ISO 13631)


DEP 31.29.42.30-Gen. Feb. 2012 Liquid ring vacuum pumps and compressors (amendments/supplements to API STD 681)


DEP 31.29.47.30-Gen. Sep. 2011 Centrifugal fans (amendments/supplements to ISO 13705, Annex E)


DEP 31.29.47.31-Gen. Feb. 2012 Centrifugal fans for petroleum, chemical and gas industry services (amendments/supplements to API 673)


DEP 31.29.47.32-Gen. Feb. 2012 Fans – Selection, testing and installation Rijsdijk, Robert L GSNL-PTE/EREQ

DEP 31.29.56.31-Gen. Sep. 2012 (A01)

Steam jet vacuum ejector sets Zoetemeijer, Len JA GSNL-PTE/EUHT

DEP 31.29.60.10-Gen. Sep. 2011 Steam turbines – Selection, testing and installation Rijsdijk, Robert L GSNL-PTE/EREQ

DEP 31.29.60.30-Gen. Feb. 2011 General-purpose steam turbines (amendments/supplements to API 611)



Special-purpose steam turbines (amendments/supplements to ISO 10437)



Lubrication, shaft-sealing and control oil systems and auxiliaries (amendments/supplements to ISO 10438)


DEP 31.29.60.33-Gen. Sep. 2011 Lubrication, shaft-sealing and oil-control systems – selection, testing, and installation


DEP 31.29.70.11-Gen. Sep. 2011 Combustion gas turbines – Selection, testing and installation


DEP 31.29.70.31-Gen. Feb. 2013 Gas turbines for the petroleum, chemical, and gas industry services (amendments/supplements to API STD 616)


DEP 31.29.70.32-Gen. Feb. 2011 Gas turbine combustion air intake and exhaust systems


DEP 31.29.80.30-Gen. Feb. 2013 Spark ignited and compression ignited engines Rijsdijk, Robert L GSNL-PTE/EREQ

DEP 31.29.90.30-Gen. Withdrawn Spark ignited gas fuelled engines

DEP 31.36.00.30-Gen. Feb. 2012 Pipeline transportation systems – Pipeline valves (amendments/supplements to ISO 14313)



Hydraulic systems for the operation of on/off valves in protective functions


DEP 31.37.00.11-Gen. Feb. 2012 (A01)

Instrument air supply Paul, Debnath SEPL-PTE/PUHT

DEP 31.38.01.10-Gen. Feb. 2013 Piping class - Basis of design Kruijer, Alfred A GSNL-PTE/EMMI

DEP 31.38.01.11-Gen. Feb. 2013 Piping - General requirements Kruijer, Alfred A GSNL-PTE/EMMI

DEP 31.38.01.12-Gen. Feb. 2013 Piping classes - Refining and chemicals Kruijer, Alfred A GSNL-PTE/EMMI



DEP 31.38.01.13-Gen. Feb. 2012 Compilation of bill of material for piping isometrics Kruijer, Alfred A GSNL-PTE/EMMI

DEP 31.38.01.15-Gen. Feb. 2013 Piping classes - Exploration and production Kruijer, Alfred A GSNL-PTE/EMMI

DEP 31.38.01.16-Gen. Withdrawn Fabrication and installation of polyethylene and polypropylene piping

DEP 31.38.01.17-Gen. Withdrawn Fabrication and installation of PVC piping

DEP 31.38.01.18-Gen. Withdrawn Fabrication and installation of glass-reinforced epoxy piping


Water injection in Downstream hydroprocessing units for corrosion control

Fan, Deyuan SIEP-PTI/GM

DEP 31.38.01.20-Gen. Feb. 2013 Design of injection points and injection systems for Downstream processing applications

Fan, Deyuan SIEP-PTI/GM

DEP 31.38.01.21-Gen. Sep. 2011 Compilation of a specification for piping systems Kruijer, Alfred A GSNL-PTE/EMMI

DEP 31.38.01.29-Gen. Feb. 2013 Pipe supports Kruijer, Alfred A GSNL-PTE/EMMI

DEP 31.38.01.31-Gen. Feb. 2013 Shop and field fabrication of piping Kruijer, Alfred A GSNL-PTE/EMMI

DEP 31.38.30.11-Gen. Feb. 2013 Protective heating of piping systems (non-electrical) Kruijer, Alfred A GSNL-PTE/EMMI


Hot-tapping on pipelines, piping and equipment Guijt, Wim GSNL-PTE/EPFA

DEP 31.38.70.21-Gen. Withdrawn Installation of PVC piping

DEP 31.38.70.22-Gen. Withdrawn Installation of PE piping

DEP 31.38.70.23-Gen. Withdrawn Installation of PP piping

DEP 31.38.70.24-Gen. Withdrawn Design and installation of glass-fibre reinforced epoxy and polyester piping (31.40.10.19)

DEP 31.38.70.25-Gen. Withdrawn Fabrication and installation of thermoplastics piping systems (31.38.01.11)

DEP 31.38.70.31-Gen. Withdrawn Requirements for PVC pipes and fittings

DEP 31.38.70.32-Gen. Withdrawn Requirements for PE pipes and fittings

DEP 31.38.70.33-Gen. Withdrawn Requirements for PP pipes and fittings

DEP 31.38.70.34-Gen. Withdrawn Requirements for glass-fibre reinforced epoxy pipes and fittings (31.38.70.37)

DEP 31.38.70.35-Gen. Withdrawn Requirements for glass-fibre reinforced polyester pipes and fittings (31.38.70.37)

DEP 31.38.70.36-Gen. Withdrawn Requirements for thermoplastics pipes and fittings (31.38.01.11)

DEP 31.38.70.37-Gen. Withdrawn Requirements for glass-fibre reinforced epoxy and polyester pipes and fittings (31.40.10.19)

DEP 31.38.82.31-Gen. Withdrawn PTFE bellows

DEP 31.38.85.93-Gen. Withdrawn Valves (Flanged/butt-welded)

DEP 31.38.85.94-Gen. Withdrawn Ball valves to API 6D

DEP 31.38.86.93-Gen. Withdrawn Valve (Class 800/1500)

DEP 31.38.87.93-Gen. Withdrawn Bronze valves (Threading: NPT)

DEP 31.40.00.10-Gen. Feb. 2013 Pipeline engineering (amendments/supplements to ISO 13623:2009)


DEP 31.40.00.11-Gen. Feb. 2013 Pipeline and subsea integrity - Design and construction


DEP 31.40.00.19-Gen. Withdrawn Corrosion mitigation strategy for wet sour gas carbon steel pipelines

RMP 31.40.00.50-Gen. Sep. 2011 Corrosion mitigation strategy for wet sour gas carbon steel pipelines


RMP 31.40.00.51-Gen. Feb. 2012 Pipeline integrity Simons, Servie JM GSNL-PTE/EPFA

DEP 31.40.10.10-Gen. Feb. 2013 Riser design Kopp, Frans SIEP-PTP/ADS




Design of multiple-pipe slug catchers Guijt, Wim GSNL-PTE/EPFA


Design of pipeline pig trap systems Guijt, Wim GSNL-PTE/EPFA

DEP 31.40.10.14-Gen. Withdrawn Pipeline overpressure protection

DEP 31.40.10.15-Gen. Feb. 2013 Analysis of spans for submerged pipelines Guijt, Wim GSNL-PTE/EPFA

DEP 31.40.10.16-Gen. Feb. 2013 Upheaval buckling of pipelines Guijt, Wim GSNL-PTE/EPFA

DEP 31.40.10.17-Gen. Apr. 2006 Pipeline/trawlgear interaction Guijt, Wim GSNL-PTE/EPFA

DEP 31.40.10.18-Gen. Feb. 2011 Pipeline engineering – Reliability-based limit states methods (amendments/supplements to ISO 16708)



Glass-fibre reinforced plastic pipeline and piping systems

Janssen, Frans AH GSNL-PTI/GM

DEP 31.40.10.20-Gen. Sep. 2012 Spoolable fibre-reinforced plastic pipes Janssen, Frans AH GSNL-PTI/GM

DEP 31.40.10.22-Gen. Feb. 2012 (A01)

Top Tension Riser Tensioning Systems Morrison, Denby G SIEP-PTP/ADF

DEP 31.40.10.31-Gen. Withdrawn Glass fibre reinforced plastic pipes and fittings (amendments/supplements to API Spec 15HR) (31.40.10.19)

RMP 31.40.10.50-Gen. Sep. 2011 Glass-fibre reinforced plastic pipeline and piping systems – Maintenance and repair

Janssen, Frans AH GSNL-PTI/GM

DEP 31.40.11.32-Gen. Sep. 2011 Pipelay survey, positioning and as-built reportings for offshore pipelines

Kopp, Frans SIEP-PTP/ADS

DEP 31.40.20.30-Gen. Withdrawn Linepipe for use in oil and gas operations under non-sour conditions (amendments/supplements to API Spec 5L) (31.40.20.35, 31.40.20.37)

DEP 31.40.20.31-Gen. Withdrawn Linepipe for use in oil and gas operations under sour conditions (amendments/supplements to API Spec 5L) (31.40.20.35, 31.40.20.37)

DEP 31.40.20.32-Gen. Sep. 2011 CRA clad or CRA-lined steel pipe (amendments/supplements to API Spec 5LD)



Linepipe induction bends (amendments/supplements to ISO 15590-1)


DEP 31.40.20.34-Gen. Feb. 2013 Welded and seamless duplex and super duplex stainless steel line pipe (amendments/supplements to API Spec 5LC)


DEP 31.40.20.35-Gen. Withdrawn Linepipe for non-critical service (amendments/supplements to ISO 3183-1)

DEP 31.40.20.36-Gen. Feb. 2013 Weldable martensitic stainless steel line pipe for use in oil and gas operations (amendments/supplements to API SPEC 5LC)


DEP 31.40.20.37-Gen. Feb. 2013 Line pipe for critical service (amendments/supplements to ISO 3183:2012 and API SPEC 5L 45th edition)


DEP 31.40.20.39-Gen. Feb. 2012 (A01)

High density polyethylene pipelines and piping systems for oilfield applications


DEP 31.40.21.30-Gen. Feb. 2013 Pipeline fittings (amendments/supplements to ISO 15590-2) and low temperature process piping fittings

Jarvie, Tom SIEP-PTP/ADS

DEP 31.40.21.31-Gen. Sep. 2011 Pipeline isolating joints (amendments/supplements to ISO 15590-2:2003)


DEP 31.40.21.32-Gen. Withdrawn Pig trap end closures (amendments/supplements to MSS SP-75) (31.40.10.13)



DEP 31.40.21.33-Gen. Sep. 2011 Pig signalers – intrusive type Guijt, Wim GSNL-PTE/EPFA

DEP 31.40.21.34-Gen. Feb. 2013 Carbon and low alloy steel pipeline flanges for use in oil and gas operations (amendments/supplements to ISO 15590-3) and low temperature carbon steel flanges for piping (amendments/supplements to ASTM A350 GR LF2)

Jarvie, Tom SIEP-PTP/ADS

DEP 31.40.21.37-Gen. Feb. 2012 Corrosion resistant alloy overlay subsea pipe and fittings excluding line pipe


DEP 31.40.30.30-Gen. Feb. 2012 Concrete coating of linepipe (amendments/supplements to ISO 21809-5)


DEP 31.40.30.31-Gen. Feb. 2011 External polyethylene and polypropylene coating for line pipe (amendments/supplements to ISO/DIS 21809-1:2009)


DEP 31.40.30.32-Gen. Feb. 2011 External fusion-bonded epoxy powder coating for line pipe (amendments/supplements to ISO 21809-2:2007)


DEP 31.40.30.33-Gen. Feb. 2013 Bituminous enamel coating of steel linepipe Guijt, Wim GSNL-PTE/EPFA

DEP 31.40.30.34-Gen. Feb. 2013 Thermoplastic lined pipelines for onshore use Janssen, Frans AH GSNL-PTI/GM

DEP 31.40.30.35-Gen. Sep. 2012 Internal coating of line pipe for non-corrosive gas transmission service (amendments/supplements to ISO 15741)


DEP 31.40.30.36-Gen. Feb. 2013 Elastomer coatings and Monel sheathing for offshore riser protection


DEP 31.40.30.37-Gen. Feb. 2013 External field joint and rehabilitation coating systems for line pipe (amendments/supplements to ISO 21809-3:2008)


DEP 31.40.30.38-Gen. Withdrawn Liquid rehabilitation coating of onshore pipelines (31.40.30.37)

DEP 31.40.30.39-Gen. Feb. 2012 Internal fusion-bonded epoxy powdercoating for water injection line pipe



Hydrostatic pressure testing of new pipelines Guijt, Wim GSNL-PTE/EPFA

DEP 31.40.50.30-Gen. Sep. 2011 Precommissioning of pipelines Guijt, Wim GSNL-PTE/EPFA

DEP 31.40.60.11-Gen. Sep. 2002 Pipeline leak detection Guijt, Wim GSNL-PTE/EPFA

DEP 31.40.60.12-Gen. Withdrawn Pipeline repairs

RMP 31.40.60.50-Gen. Feb. 2011 Pipeline repairs Guijt, Wim GSNL-PTE/EPFA

DEP 31.40.70.30-Gen. Feb. 2013 Quarter-turn actuators for on/off valves Mooi, Peter GSNL-PTE/EPAC

DEP 31.41.10.30-Gen. Withdrawn Steel pipe for use as casing or tubing for wells (amendments/supplements to ISO 11960)

DEP 31.46.00.31-Gen. Feb. 2012 Acoustic insulation for piping (amendments/supplements to ISO 15665)


DEP 31.51.10.31-Gen. Feb. 2013 Tank mixers and agitators Rijsdijk, Robert L GSNL-PTE/EREQ

DEP 31.76.10.10-Gen. Feb. 2013 Heating, ventilation and air conditioning for plant buildings


DEP 31.76.10.11-Gen. Withdrawn Installation, testing and balancing, and commissioning of HVAC systems

DEP 32.00.00.10-Gen. Withdrawn The division of responsibilities between instrument and electrical engineering disciplines

DEP 32.00.00.11-Gen. Withdrawn Human-machine interface in a control room (30.00.60.15, 32.80.10.14)

DEP 32.00.00.12-Gen. Feb. 2013 Fiscal and sales allocation models for Upstream production systems

Mooi, Peter GSNL-PTE/EPAC

DEP 32.01.20.10-Gen. Withdrawn Data acquisition and control architecture (DACA)

DEP 32.01.20.12-Gen. Feb. 2012 Process Control Domain – Enterprise industrial automation information technology and security

Dehler, Glenn SCAI-PTE/APAC



RMP 32.01.20.50-Gen. Feb. 2012 Process Control Domain – Enterprise industrial automation information technology and security


DEP 32.01.21.10-Gen. Withdrawn Data acquisition & control architecture (DACA) – Roles and responsibilities

DEP 32.01.22.10-Gen. Withdrawn Data acquisition & control architecture (DACA) – Procedural controls – Configuration management

DEP 32.01.22.11-Gen. Withdrawn Data acquisition & control architecture (DACA) – Procedural controls – Backup and restore

DEP 32.01.22.12-Gen. Withdrawn Data acquisition & control architecture (DACA) – Procedural controls – Incident management

DEP 32.01.22.13-Gen. Withdrawn Data acquisition & control architecture (DACA) – Procedural controls – Disconnection procedure

DEP 32.01.23.10-Gen. Withdrawn Data acquisition & control architecture (DACA) – Technical controls – Security administration

DEP 32.01.23.11-Gen. Withdrawn Data acquisition & control architecture (DACA) – Technical controls – Infrastructure architecture

DEP 32.01.23.12-Gen. Withdrawn Data acquisition & control architecture (DACA) – Technical controls – Remote user access

DEP 32.01.23.13-Gen. Withdrawn Data acquisition & control architecture (DACA) – Technical controls – Wireless security

DEP 32.01.23.14-Gen. Withdrawn Data acquisition & control architecture (DACA) – Technical controls – Minimal access

DEP 32.01.23.15-Gen. Withdrawn Data acquisition & control architecture (DACA) – Technical controls – Authentication and authorisation

DEP 32.01.23.17-Gen. Feb. 2011 Process control domain – Security requirements for suppliers


DEP 32.01.23.18-Gen. Withdrawn Data acquisition & control architecture (DACA) – Technical controls – PCD network drawings

DEP 32.01.23.19-Gen. Withdrawn Data acquisition & control architecture (DACA) – Technical controls – Architectural requirements for applications utilizing production data

DEP 32.01.25.10-Gen. Withdrawn Data acquisition and control architecture (DACA) – System security – Virus management

DEP 32.01.25.11-Gen. Withdrawn Data acquisition & control architecture (DACA) – System security – Patch management

DEP 32.01.26.11-Gen. Withdrawn Data acquisition & control architecture (DACA) – Assurance – Risk assessment

DEP 32.01.40.31-Gen. Feb. 2012 Requirements for real-time production operations and production-critical real-time data

Berendschot, Leo GSUSI-PTT/ESMA

DEP 32.10.00.10-Gen. Withdrawn Instrumentation

DEP 32.10.03.10-Gen. Feb. 2011 Instrument symbols and identification on process engineering flow schemes

Ramani, Ganesh PTIN-PTE/PPAC

DEP 32.10.03.11-Gen. Withdrawn Symbols and identification system – Instrumentation. Part 2: -Functional logic diagrams (32.10.03.10)

DEP 32.10.03.12-Gen. Withdrawn Symbols and identification system – Instrumentation. Part 3: -Instrumentation loop diagrams (32.10.03.10)

DEP 32.24.20.30-Gen. Withdrawn Control system and instrumented protective functions for fired equipment – System for a single-burner furnace (S 24.024 and S 24.026)

DEP 32.24.20.33-Gen. Withdrawn Control system and instrument protective functions for fired equipment System for an automatically started, gas fired, natural draught, multi-burner furnace, safeguarded by pilot burners (S 24.033)

DEP 32.24.20.37-Gen. Withdrawn Control system and instrumented protective functions for fired equipment – System for a manually-started, forced draught, multi-burner furnace or boiler (S 24.021)



DEP 32.24.20.38-Gen. Withdrawn Control system and instrumented protective functions for fired equipment – System for an automatically-started, forced draught, multi-burner furnace or boiler (S 24.030 or S 24.034)

DEP 32.24.20.40-Gen. Withdrawn Control system and instrumented protective functions for fired equipment – System for a tangentially gas-fired CO boiler (S 24.036)

DEP 32.24.20.42-Gen. Withdrawn Control system and instrumented protective functions for fired equipment – Systems for Co-fired gas turbine waste heat recovery units

DEP 32.24.20.44-Gen. Feb. 2013 Instrumentation control and protection for fired equipment


DEP 32.29.20.10-Gen. Feb. 2013 Safeguarding and instrumented protective functions for rotating equipment


DEP 32.30.10.30-Gen. Withdrawn System cabinets

DEP 32.30.20.11-Gen. Sep. 2011 (Feb. 2012 Circ.)

Fire, gas and smoke detection systems Hopwood, Bruce B GSUK-PTE/EPAC

DEP 32.30.20.13-Gen. Sep. 2011 FOUNDATION™ Fieldbus – Design and configuration

Gul, Rong P GSNL-PTE/EPAC

DEP 32.30.20.14-Gen. Feb. 2012 Instrument asset management Gul, Rong P GSNL-PTE/EPAC

DEP 32.30.20.15-Gen. Sep. 2011 DCS basic application standards Williamson, John M GSUSI-PTE/APAC

DEP 32.30.20.16-Gen. Sep. 2011 (A01)

Baselayer control applications Williamson, John M GSUSI-PTE/APAC

DEP 32.30.20.17-Gen. Feb. 2012 Integration of motor controls into BPCs Whitaker, Robert D GSUSI-PTE/APAC

DEP 32.30.20.18-Gen. Sep. 2012 Real-time optimization project standards Stoever, Matthew A GSUSI-PTE/APAC

RMP 32.30.20.50-Gen. Feb. 2011 Fire, gas and smoke detection systems Hopwood, Bruce B GSUK-PTE/EPAC

DEP 32.31.00.10-Gen. Withdrawn Instrument engineering procedures

DEP 32.31.00.32-Gen. Feb. 2011 (Sep. 2011 Circ.) (Feb. 2012 Circ.) (A03)

Instruments for measurement and control Mooi, Peter GSNL-PTE/EPAC

DEP 32.31.00.34-Gen. Sep. 2011 Instrumentation documents and drawings Ramani, Ganesh PTIN-PTE/PPAC

DEP 32.31.00.35-Gen. Feb. 2013 Smartplant instrumentation (SPI) - Project execution Whitaker, Robert D GSUSI-PTE/APAC


Instrumentation for equipment packages Mooi, Peter GSNL-PTE/EPAC

DEP 32.31.09.32-Gen. Feb. 2013 Heat exchanger instrumentation requirements for performance assessment


DEP 32.31.31.30-Gen. Withdrawn Signal light assemblies

DEP 32.31.50.10-Gen. Sep. 2012 On-line process analysers Mooi, Peter GSNL-PTE/EPAC

DEP 32.31.50.11-Gen. Withdrawn On-line process stream analysis – Sample conditioning (32.31.50.10)

DEP 32.31.50.12-Gen. Withdrawn On-line process stream analysis – Analysers (32.31.50.10)

DEP 32.31.50.13-Gen. Sep. 2012 Analyser housing Mooi, Peter GSNL-PTE/EPAC

DEP 32.31.50.31-Gen. Withdrawn On-line process stream analysers

DEP 32.31.56.30-Gen. Sep. 2011 Implementation of near-infrared systems for main fuels blending

van Duyn, Marcel O GSNL-PTD/TASE

DEP 32.32.00.11-Gen. Sep. 2012 (A01)

Custody transfer measurement systems for liquids Mooi, Peter GSNL-PTE/EPAC

DEP 32.32.00.12-Gen. Feb. 2013 Custody transfer measurement systems for gases and vapours




DEP 32.32.00.13-Gen. Feb. 2013 Flow rate measurement in wet gas environments by means of Venturi tubes and tracer dilution technology


DEP 32.32.10.10-Gen. Withdrawn Flow instruments (32.31.00.32)

DEP 32.32.11.45-Gen. Withdrawn Sizing form for square edge orifices with corner tappings

DEP 32.32.11.46-Gen. Withdrawn Sizing form for square edge orifices with radius tappings

DEP 32.32.11.47-Gen. Withdrawn Sizing form for quarter of circle orifices with flange tappings

DEP 32.32.11.48-Gen. Withdrawn Sizing form for conical entrance orifices with corner tappings

DEP 32.32.11.49-Gen. Withdrawn Sizing form for Venturi tubes (A, B and C)

DEP 32.32.11.50-Gen. Withdrawn Sizing form for rectangular Venturi tubes

DEP 32.32.11.51-Gen. Withdrawn Sizing form ISA 1932 nozzles

DEP 32.32.11.52-Gen. Withdrawn Sizing form for long radius nozzles

DEP 32.32.11.53-Gen. Withdrawn Flow factor calculation form for square edge orifices with flange tappings

DEP 32.32.11.60-Gen. Withdrawn Flow factor calculation form for square edge orifices with corner tappings

DEP 32.32.11.61-Gen. Withdrawn Flow factor calculation form for square edge orifices with radius tappings

DEP 32.32.11.62-Gen. Withdrawn Flow factor calculation form for quarter of a circle orifices with flange tappings

DEP 32.32.11.63-Gen. Withdrawn Flow factor calculation form for conical entrance orifices with corner tappings

DEP 32.32.11.64-Gen. Withdrawn Flow factor calculation form for Venturi tubes (A,B and C)

DEP 32.32.11.65-Gen. Withdrawn Flow factor calculation form for rectangular Venturi tubes

DEP 32.32.11.66-Gen. Withdrawn Flow factor calculation form for ISA 1932 nozzles

DEP 32.32.11.67-Gen. Withdrawn Flow factor calculation form for long radius nozzles

DEP 32.32.11.81-Gen. Withdrawn Sizing form for square edge orifices with flange tappings

DEP 32.35.00.10-Gen. Withdrawn Reference tables for thermocouples

DEP 32.35.00.20-Gen. Withdrawn Reference tables for resistance thermometers

DEP 32.36.00.31-Gen. Withdrawn Selection and specification of final control elements

DEP 32.36.01.11-Gen. Withdrawn Sizing of control valves

DEP 32.36.01.15-Gen. Withdrawn Control valve noise

DEP 32.36.01.16-Gen. Withdrawn Sizing of control valves (32.36.01.17)

DEP 32.36.01.17-Gen. Feb. 2013 Control valves - Selection, sizing, and specification Mooi, Peter GSNL-PTE/EPAC

DEP 32.36.01.41-Gen. Withdrawn Control valve calculation form: Compressible fluids

DEP 32.36.01.42-Gen. Withdrawn Control valve calculation form: Incompressible fluids

DEP 32.37.00.31-Gen. Withdrawn Installation of instruments

DEP 32.37.00.33-Gen. Withdrawn Mounting of plant instruments (32.31.00.32)

DEP 32.37.00.80-Gen. Withdrawn Summary of instrument process connections

DEP 32.37.02.80-Gen. Withdrawn Summary of instrument installation materials

DEP 32.37.02.81-Gen. Withdrawn Instrument impulse lines “Metric version”

DEP 32.37.02.82-Gen. Withdrawn Instrument impulse lines “Imperial version”

DEP 32.37.02.83-Gen. Withdrawn Instrument air lines

DEP 32.37.02.84-Gen. Withdrawn Instrument nameplates

DEP 32.37.10.11-Gen. Sep. 2012 Installation of on-line instruments Mooi, Peter GSNL-PTE/EPAC



DEP 32.37.10.31-Gen. Withdrawn Prefabricated instrument consoles

DEP 32.37.10.34-Gen. Withdrawn Instrument nameplates (32.31.00.32)

DEP 32.37.20.10-Gen. Sep. 2011 Instrument signal lines Znotins, Andy SCAI-PTE/APAC

DEP 32.37.20.31-Gen. Withdrawn System cabling (32.37.20.10)

DEP 32.37.51.11-Gen. Withdrawn Instrument air lines (31.37.00.11)


Instrumentation of depressuring systems Jirathunyawg, Akachai PTIN-PTE/PPAC

RMP 32.45.10.50-Gen. Feb. 2011 Instrumentation of depressuring systems Jirathunyawg, Akachai PTIN-PTE/PPAC


Plant telecommunication Akkermans, Frans F QSGTL-ITV/UM

DEP 32.71.00.11-Gen. Feb. 2013 Telecommunications standards Akkermans, Frans F QSGTL-ITV/UM

DEP 32.71.00.12-Gen. Feb. 2013 Telecommunications for offshore facilities Akkermans, Frans F QSGTL-ITV/UM

DEP 32.71.00.13-Gen. Feb. 2013 Drilling communications Akkermans, Frans F QSGTL-ITV/UM

DEP 32.71.00.14-Gen. Feb. 2013 Telecommunications towers and guyed masts Akkermans, Frans F QSGTL-ITV/UM

DEP 32.71.00.16-Gen. Withdrawn Design and installation of telephone cabling

DEP 32.71.00.30-Gen. Feb. 2013 Structured cabling systems for telecommunications Akkermans, Frans F QSGTL-ITV/UM

DEP 32.71.00.31-Gen. Feb. 2013 Telecommunications transmission system Akkermans, Frans F QSGTL-ITV/UM


Instrumented protective functions (IPF) Jirathunyawg, Akachai PTIN-PTE/PPAC

DEP 32.80.10.11-Gen. Withdrawn Implementation of instrumented protective functions class x

DEP 32.80.10.12-Gen. Withdrawn Management of instrumented protective functions

DEP 32.80.10.13-Gen. Withdrawn High integrity pressure protecting systems (HIPPS SIL-4)


Alarm management Whitaker, Robert D GSUSI-PTE/APAC

DEP 32.80.10.30-Gen. Withdrawn Instrumented protective systems

RMP 32.80.10.50-Gen. Feb. 2011 The operation, testing and maintenance of instrumented protective functions (IPF)

Jirathunyawg, Akachai PTIN-PTE/PPAC

DEP 33.00.20.11-Gen Withdrawn Electrical supply systems

DEP 33.10.03.10-Gen. Withdrawn Symbols and identification system – Electrical (S 64.000)

DEP 33.10.04.11-Gen Withdrawn Comparison of electrical codes

DEP 33.10.64.11-Gen Withdrawn Transistor-type signal light assemblies

DEP 33.10.64.12-Gen Withdrawn Electrical signaling devices

DEP 33.10.79.11-Gen Withdrawn Emergency electricity supply for lighting and instrumentation

DEP 33.64.10.10-Gen. Feb. 2011 Electrical engineering design de Wilt, Wim GSNL-PTE/EELE

DEP 33.64.10.11-Gen. Withdrawn Electrical network monitoring and control system for industrial networks – Application

DEP 33.64.10.12-Gen. Sep. 2011 Electrical supply and generation – Design and operation

Donnellan, Paul J GSNL-PTE/EELE

DEP 33.64.10.17-Gen. Sep. 2011 Application of protective functions for electrical systems

de Wilt, Wim GSNL-PTE/EELE

DEP 33.64.10.30-Gen. Withdrawn Electric power and lighting installations (33.64.10.10)

DEP 33.64.10.32-Gen. Sep. 2011 Electrical network monitoring and control system for industrial networks


DEP 33.64.10.33-Gen. Sep. 2012 Electromagnetic compatibility (EMC) de Wilt, Wim GSNL-PTE/EELE



DEP 33.64.20.10-Gen. Feb. 2013 Electrical engineering design for North American application


DEP 33.64.30.30-Gen. Sep. 2011 Electrical packaged equipment requirements for North American application


DEP 33.65.11.31-Gen. Feb. 2012 Synchronous AC machines (amendments/supplements to IEC 60034-1 and IEC 60034-14)


DEP 33.65.11.32-Gen. Feb. 2013 Packaged alternating current generator sets Donnellan, Paul J GSNL-PTE/EELE

DEP 33.65.11.34-Gen. Feb. 2012 Synchronous AC machines for North American application (amendments/supplements to API 546)


DEP 33.65.11.35-Gen. Feb. 2013 Packaged unit AC generator sets for North American applications


DEP 33.65.40.31-Gen. Sep. 2011 Power transformers (amendments/supplements to IEC 60076-1 and IEC 60076-11)


DEP 33.65.40.32-Gen. Sep. 2011 Liquid-immersed transformers for North American application


DEP 33.65.50.31-Gen. Feb. 2011 Static DC uninterruptible power supply (DC UPS) units


DEP 33.65.50.32-Gen. Feb. 2011 Static A.C. uninterruptible power supply unit (static A.C. UPS unit)


DEP 33.65.50.33-Gen. Feb. 2012 Design and fabrication of AC uninterruptible power supplies for North American application


DEP 33.65.50.34-Gen. Feb. 2012 Design and fabrication of DC uninterrupt ble power supplies for North American application


DEP 33.65.60.30-Gen. Feb. 2012 Solar power systems Donnellan, Paul J GSNL-PTE/EELE

DEP 33.66.05.10-Gen. Withdrawn Engineering guidelines variable speed drive systems (technique and applications)

DEP 33.66.05.31-Gen. Feb. 2012 Electrical machines – Cage-induction types (amendments/supplements to IEC 60034-1 and IEC 60034-14)


DEP 33.66.05.32-Gen. Feb. 2013 AC electrical adjustable speed drive systems - Rated 375 KW and larger for North American application (amendments to IEEE STD 1566:2005)


DEP 33.66.05.33-Gen. Feb. 2012 A.C. electrical variable speed drive systems de Wilt, Wim GSNL-PTE/EELE

DEP 33.66.05.35-Gen. Sep. 2011 LV induction motors for North American application(Amendments/supplements to IEEE STD 841)


DEP 33.66.05.36-Gen. Feb. 2012 MV induction motors for North American application (amendments/supplements to API 541)


DEP 33.66.05.37-Gen. Sep. 2011 General-purpose form-wound squirrel cage induction motors – 250 horsepower and larger for North American application (amendments/supplements to API 547)

Barrios, Louis A GSUSI-PTE/AELE

DEP 33.66.05.38-Gen. Sep. 2011 Design and fabrication of MV motor control centres for North American application (amendments to UL 347/CAS C22.2 No. 253-09)


DEP 33.66.05.39-Gen. Feb. 2012 Design and fabrication of low voltage motor control centres for North American application (amendments to UL 845 / CAS C22.2 No. 254-05)


DEP 33.67.01.31-Gen. Feb. 2011 Low voltage switchgear and controlgear assemblies (amendments/supplements to IEC 60439)



Design and fabrication of LV switchgear for North American applications



Design and fabrication of MV switchgear for North American applications




DEP 33.67.40.31-Gen. Feb. 2013 Design and fabrication of MV metal-enclosed interrupter switchgear for North American applications (amendments/supplements to IEEE C37.20.3:2006)


DEP 33.67.51.31-Gen. Feb. 2012 High-voltage switchgear and controlgear assemblies for rated voltages between 1 kV and 52 kV (amendments/supplements to IEC 62271-200)


DEP 33.68.30.31-Gen. Feb. 2013 Electrical heating system for frost heave prevention of refrigerated hydrocarbon storage tanks


DEP 33.68.30.32-Gen. Feb. 2013 Electrical trace heating Donnellan, Paul J GSNL-PTE/EELE

DEP 33.68.30.33-Gen. Feb. 2013 Electrical process heaters Donnellan, Paul J GSNL-PTE/EELE

DEP 33.68.30.34-Gen. Feb. 2013 Electrical trace heating for North American application



Navigational aids for fixed offshore structures de Wilt, Wim GSNL-PTE/EELE


Earthquake design for onshore facilities – Seismic hazard assessment


DEP 34.00.01.30-Gen. Sep. 2011 Structural design and engineering of onshore structures


DEP 34.11.00.10-Gen. Sep. 2011 Onshore & Nearshore Site investigations Cunningham, Mark R GSNL-PTE/ECSO

DEP 34.11.00.11-Gen. Sep. 2011 Site preparation and earthworks including tank foundations and tank farms


DEP 34.11.00.12-Gen. Feb. 2011 (Sep 2011 Circ.; Feb. 2012 Circ.; A03)

Geotechnical and foundation engineering – Onshore Cunningham, Mark R GSNL-PTE/ECSO

DEP 34.13.20.31-Gen. Sep. 2011 Roads, paving, surfacing, cable trenches, slope protection and fencing



Drainage systems and primary treatment facilities Kruijsen, Ton ATJJM GSNL-PTE/ECSO

DEP 34.17.00.32-Gen. Sep. 2012 Design and engineering of buildings Kruijsen, Ton ATJJM GSNL-PTE/ECSO

DEP 34.17.10.30-Gen. Feb. 2012 Design of blast resistant onshore buildings, control rooms and field auxiliary rooms


DEP 34.17.10.31-Gen. Sep. 2012 Laboratories Kooistra, Hielke E GSNL-PTD/TASE

DEP 34.17.10.33-Gen. Feb. 2013 Portable blast resistant modules Kruijsen, Ton ATJJM GSNL-PTE/ECSO

DEP 34.17.10.34-Gen. Feb. 2013 Requirements for mobile and construction camps Kruijsen, Ton ATJJM GSNL-PTE/ECSO

DEP 34.17.10.35-Gen. Feb. 2011 Siting of onshore occupied portable buildings Salter, Natalie Y GSUSI-PTE/DAPP

DEP 34.17.10.36-Gen. Feb. 2012 Inflatable blast resistant shelters Salter, Natalie Y GSUSI-PTE/DAPP

DEP 34.17.10.37-Gen. Feb. 2013 Design and fabrication of modular electrical power centers for North American application


DEP 34.18.02.31-Gen Withdrawn Piling

DEP 34.18.51.10-Gen. Withdrawn Minimum requirements for the construction and maintenance of tank foundations, bund walls and drainage systems for small storage installations (34.11.00.11)

DEP 34.19.19.11-Gen. Sep. 2011 Grouting of equipment and structure bases Kruijsen, Ton ATJJM GSNL-PTE/ECSO




Passive fire protection for onshore facilities Kruijsen, Ton ATJJM GSNL-PTE/ECSO

DEP 34.19.20.31-Gen. Sep. 2011 Reinforced concrete structures Kruijsen, Ton ATJJM GSNL-PTE/ECSO

DEP 34.19.61.11-Gen Withdrawn Chemical-resistant linings for concrete structures

DEP 34.24.26.31-Gen. Sep. 2012 Chimneys selection, design and engineering (based on EN 1992-1-1, EN 1993-3-2, EN 1443, EN 13084 Parts 1, 2, 4, 5, 6, 7 and 8)


DEP 34.24.27.31-Gen. Withdrawn Reinforced concrete stacks

DEP 34.28.00.31-Gen. Sep. 2011 Onshore Steel structures Kruijsen, Ton ATJJM GSNL-PTE/ECSO


Onshore ancillary steel structures Kruijsen, Ton ATJJM GSNL-PTE/ECSO

DEP 34.28.90.11-Gen Withdrawn Fireproofing of steel structures

DEP 34.51.00.11-Gen. Withdrawn Standard tanks


Vertical steel storage tanks - Selection design and construction (amendments/supplements to EN 14015)



Full containment refrigerated LNG tanks Kruijsen, Ton ATJJM GSNL-PTE/ECSO

DEP 34.51.01.33-Gen. Feb. 2012 (A01)

Aboveground vertical storage tanks (amendments/supplements to API Standard 650)


DEP 34.51.01.33-Gen. Feb. 2012 Aboveground vertical storage tanks (amendments/supplements to API Standard 650)


DEP 34.51.01.34-Gen. Feb. 2012 Full containment refrigerated LPG tanks Kruijsen, Ton ATJJM GSNL-PTE/ECSO

DEP 34.51.11.30-Gen. Feb. 2013 Mounded horizontal cylindrical vessels for pressurised storage of LPG at ambient temperatures (amendments/supplements to EEMUA 190)


DEP 34.51.90.10-Gen. Sep. 2012 Demolition of storage tanks (endorsement of EEMUA 154)


DEP 34.74.00.10-Gen. Feb. 2013 Cooling water towers - Selection, design, fabrication and erection


DEP 34.76.30.31-Gen. Withdrawn Heating and air conditioning in sub-stations and switch houses (31.76.10.10)

DEP 35.00.00.10-Gen. Feb. 2012 (A01)

Vessel Integrity, Marine Systems - Requirements for Selection and Operation of Vessels (Endorsement of DNV RP-H104)


DEP 35.00.10.10-Gen. Feb. 2013 Design of jetty facilities (amendments/supplements to BS 6349-1/2/4)


DEP 37.00.10.10-Gen. Feb. 2011 Metocean design and operating considerations (endorsement of ISO 19901-1:2005)

Vogel, Michael J GSUSI-PTE/ACSO

DEP 37.00.10.11-Gen. Feb. 2012 Metocean data acquisition - Definition, implementation and analysis

Vogel, Michael J GSUSI-PTE/ACSO

DEP 37.00.10.12-Gen. Feb. 2012 Metocean data acquisition - Real time systems Vogel, Michael J GSUSI-PTE/ACSO

DEP 37.01.10.10-Gen. Feb. 2011 Offshore production installations basic surface process safety systems



Design of offshore topsides facilities against fire and blast loading (amendments/supplements to API RP-2FB)

Rhodes, Terry C SUKEP-UIE/T/PE


Design of seawater systems for offshore and onshore

Paul, Debnath SEPL-PTE/PUHT



DEP 37.05.10.11-Gen. Feb. 2012 Diesel oil systems Paul, Debnath SEPL-PTE/PUHT

DEP 37.05.10.12-Gen. Withdrawn Design of hose bu k transfer facilities for offshore installations


Site specific assessment of mobile offshore jack-up units

Cunningham, Mark R GSNL-PTE/ECSO


Drain systems for offshore installations Kruijsen, Ton ATJJM GSNL-PTE/ECSO

DEP 37.17.10.10-Gen. Feb. 2013 Design of offshore living quarters Rhodes, Terry C SUKEP-UIE/T/PE

DEP 37.17.10.11-Gen. Jan. 2011 (Sep. 2011 Circ.) (Feb. 2012 Circ.)

Design of offshore temporary refuges Rhodes, Terry C SUKEP-UIE/T/PE

DEP 37.19.00.10-Gen. Feb. 2011 Offshore structures - General requirements (endorsement of ISO 19900)


DEP 37.19.00.12-Gen. Feb. 2012 (A01)

Offshore topsides structures (amendments/supplements to ISO 19901-3:2010)


DEP 37.19.00.14-Gen. Feb. 2013 Seismic design procedures and criteria - offshore (amendments/supplements to ISO 19901-2)



Fixed steel offshore structures (amendments/supplements to ISO 19902:2007)


DEP 37.19.10.30-Gen. Sep. 2011 Weldable structural steels for fixed offshore structures (amendments/supplements to EN 10225 and EN 10025)


DWS 37.19.20.11-Gen. Sep. 2011 Weight management plan for floating platforms (amendments/supplements to ISO 19901-5)


DEP 37.19.30.30-Gen. Sep. 2011 Cathodic protection systems for fixed offshore steel structures (amendments/supplements to NACE SP0176-2007)


DEP 37.19.60.10-Gen. Withdrawn Structural inspection of offshore installations

RMP 37.19.60.50-Gen. Feb. 2011 Structural inspection of offshore installations Rhodes, Terry C SUKEP-UIE/T/PE


Firewater pumps for offshore installations Rijsdijk, Robert L GSNL-PTE/EREQ


HVAC for offshore installations (amendments/supplements to ISO 15138)


DEP 37.80.00.30-Gen. Feb. 2013 Subsea production systems Still, Ian RW SIEP-PTP/ADS

DEP 37.80.00.31-Gen. Withdrawn Design and operation of subsea production systems – General requirements and recommendations (endorsement of ISO 13628-1)

DEP 37.80.00.33-Gen. Sep. 2010 Design and operation of subsea production control systems (amendments/supplements to ISO 13628-6)

Still, Ian RW SIEP-PTP/ADS

DEP 37.80.00.35-Gen. Feb. 2013 Subsea pipeline valves (amendments/supplements to ISO 14723)


DEP 37.80.00.36-Gen. Feb. 2013 Deepwater subsea vertical tree systems (amendments/supplements to ISO 13628-4/ API 17D)


DEP 37.80.00.38-Gen. Sep. 2011 Deepwater jumper design, measurement, fabrication and testing


DEP 37.80.01.31-Gen. Withdrawn Design and operation of subsea production systems – Unbonded flexible pipe systems for subsea and marine applications (endorsement of ISO 13628-2)



DEP 37.80.01.32-Gen. Withdrawn Design and operation of subsea production systems – Through flowline (TFL) systems (endorsement of ISO 13628-3)

DEP 37.80.01.33-Gen. Withdrawn Design and operation of subsea production systems – Subsea umbilicals (endorsement of ISO 13628-5)

DEP 37.80.01.34-Gen. Withdrawn Design and operation of subsea production systems – Specification for bonded flexible pipe (endorsement of ISO 13628-10)

DEP 37.80.01.35-Gen. Withdrawn Design and operation of subsea production systems – Flexible pipe systems for subsea and marine applications (endorsement of ISO 13628-11)

DEP 37.80.01.36-Gen. Withdrawn Design and operation of subsea production systems – Dynamic production risers (endorsement of ISO 13628-12)

DEP 37.80.02.31-Gen. Feb. 2011 (A01)

Seamless super duplex tubing manufacturing specification for umbilicals and subsea distribution hardware


DEP 37.80.02.32-Gen. Sep. 2011 Seam Welded Super Duplex Tubing Manufacturing Specification for Umbilicals and Subsea Distribution Hardware

Von Tungeln, Robert K SIEP-PTP/ADS

DEP 37.80.02.33-Gen. Feb. 2011 Zinc clad duplex tubing manufacturing specification Still, Ian RW SIEP-PTP/ADS

DEP 37.80.02.35-Gen. Feb. 2011 Medium voltage, 6kV (Um = 7.2kV) to 30kV (Um = 36kV), power conductors for deepwater umbilicals


DEP 37.80.02.36-Gen. Feb. 2013 Deepwater umbilical manufacturing (amendments/supplements to ISO 13628-5:2009)


DEP 37.80.02.37-Gen. Feb. 2011 (A01)

Deepwater subsea controls, power, and chemical distribution manufacturing specification


DEP 37.80.02.38-Gen. Withdrawn Umbilical topside termination and interface equipment

DEP 37.80.03.30-Gen. Feb. 2013 Umbilical transportation and installation (amendments/supplements to ISO 13628-5:2009)


DEP 37.80.03.31-Gen. Sep. 2011 Deepwater subsea distribution hardware installation Still, Ian RW SIEP-PTP/ADS

DEP 37.80.10.30-Gen. Sep. 2011 Deepwater subsea completion/workover systems (amendments/supplements to ISO 13628-7)

LaCaze, David A SIEP-PTP/ADS

DEP 37.81.00.11-Gen. Feb. 2013 Offshore coordination team management and construction hook-up work planning



Generic design and analysis for steel catenary risers and catenary umbilical systems for offshore structures


DWS 37.81.10.11-Gen. Feb. 2012 Design and analysis of top tension risers for deepwater offshore floating structures (based on API RP 2RD/ ISO WD 13628-12)


DEP 37.81.10.12-Gen. Sep. 2011 Design of anchor piles for deepwater mooring systems (based on API RP 2SK)


DEP 37.81.10.13-Gen. Feb. 2013 Global design and analysis of permanently moored deepwater floating production systems (amendments/supplements to API RP 2FPS, API RP 2SK and API RP 2SM)


DEP 37.81.10.14-Gen. Sep. 2011 Global design and analysis of deepwater tension leg platforms (amendments/supplements to API RP-2T)


DEP 37.81.10.15-Gen. Sep. 2012 Pipe-soil interaction on a normally consolidated clay seabed


DWS 37.81.10.18-Gen. Sep. 2011 Design specification for deepwater tension leg platform, semisubmersible and spar hull (based on API RP 2T and API RP 2FPS)


DEP 37.81.10.19-Gen. Sep. 2011 Marine operations requirements - loadout, transportation and installation deepwater structures (amendments/supplements to ISO 19901-6 or API RP 2MOP)




DEP 37.81.10.20-Gen. Sep. 2011 Design of driven pile foundations for tension leg platforms (based on API RP 2T)


DEP 37.81.10.21-Gen. Sep. 2011 Structural design of tendon systems for deepwater offshore tension leg platforms (amendments/supplements to API RP 2T)


DEP 37.81.10.30-Gen. Sep. 2012 Design, fabrication and testing requirements for deepwater project VIV suppression strakes for SCR's, TTR's, umbilicals, TLP tendons and jumpers


DEP 37.81.10.31-Gen. Sep. 2011 Structural steel design of small deepwater offshore skids, facility packages, and subsea sleds and manifolds (based on AISC Steel Construction Manual ASD, API RP 2A-WSD and AWS D1.1)


DEP 37.81.10.32-Gen. Sep. 2011 (A01) (A02)

Structural steel fabrication of small deepwater offshore skids, facility packages, and subsea sleds and manifolds (based on AISC steel construction manual ASD, API RP 2A-WSD and AWS D1.1)


DEP 37.81.10.33-Gen. Sep. 2011 Structural welding and inspection of deepwater floating production systems (amendments/supplements to AWS D1.1/D1.1M:2008)


DEP 37.81.10.34-Gen. Feb. 2013 Structural fabrication of deepwater floating production systems


DWS 37.81.10.36-Gen. Sep. 2011 Structural steel design of deepwater offshore topsides decks for floating systems


DEP 37.81.10.37-Gen Withdrawn Recommended practice for SIEP-EPP Designed structural steel topsides decks for deepwater offshore floating systems (based on AISC Steel construction manualASD, API RP 2A-WSD, and AWS D1.1)

DEP 37.81.10.38-Gen. Sep. 2012 Design, fabrication and testing requirements of permanent VIV suppression fairing systems for offshore structures


DEP 37.81.20.30-Gen. Feb. 2013 Manufacture, testing, and inspection of carbon and low-alloy steel castings Grades 345-586 N/mm2 (50-85 KSI) for primary steel applications in deepwater offshore structures and pipelines


DEP 37.81.20.31-Gen. Sep. 2011 Galvanic anodes for marine structures and pipelines – Specification and qualification – Modifications to ISO 15589-2


DEP 37.81.20.33-Gen. Sep. 2012 Manufacture, testing, and inspection of weldable structural steel plate grades 345 552 N/mm2 (50-80 ksi) for special/critical steel applications in deepwater offshore structures (based on ASTM A20)


DEP 37.81.20.34-Gen. Sep. 2012 Manufacture, testing, and inspection of weldable structural steel plate grades 345-552 N/mm2 (50-80 ksi) for primary steel applications in deepwater offshore structures (based on ASTM A6)


DWS 37.81.20.35-Gen. Feb. 2011 (Sep. 2011 Circ.) (Feb. 2012 Circ.)

Technical specification for elastomeric flexible joints for use in deepwater offshore dynamic riser applications


DEP 37.81.20.36-Gen Feb. 2012 Syntactic foam buoyancy modules for use in deepwater offshore dynamic riser applications


DEP 37.81.20.37-Gen. Sep. 2012 Manufacture, testing, and inspection of carbon and low-alloy steel forgings for special/critical steel applications in deepwater offshore structures and pipelines




DEP 37.81.20.38-Gen. Feb. 2013 Manufacture, testing, and inspection of weldable structural rolled shapes grades 345-483 N/mm2 (50-70 KSI) for primary steel applications in deepwater offshore structures (based on ASTM A6)


DEP 37.81.20.39-Gen. Sep. 2012 Manufacture, testing, and inspection of carbon and low-alloy steel forgings for primary steel applications in deepwater offshore structures and pipelines (based on ASTM A788, ASTM A961 and MSS SP-75)


DEP 37.81.20.40-Gen. Sep. 2011 Impressed current laboratory testing of aluminum alloy anodes (amendments/supplements to NACE STD TM0190-2006)


DEP 37.81.21.30-Gen. Feb. 2012 (A01)

Manufacture, testing, and inspection of permanent mooring system chain and accessories for floating structures (based on DNV-OS-E302)


DEP 37.81.21.31-Gen. Feb. 2012 (A01)

Permanent Mooring System Wire Rope, Sockets, Pins and Connectors for Deepwater Floating Structures (Based on DNV-OS-E304)


DEP 37.81.21.32-Gen. Feb. 2013 Surface preparation, materials, application, and quality control testing of aluminum-ceramic basecoat with resin-bonded fluorocarbon topcoat coating systems for deepwater offshore equipment


DEP 37.81.21.33-Gen. Feb. 2013 Surface preparation, materials, application, and quality control testing of low friction corrosion resistant fluorocarbon coating systems for deepwater offshore equipment


DEP 37.81.21.34-Gen. Feb. 2013 Thermal-sprayed ceramic coating requirements Morrison, Denby G SIEP-PTP/ADF

DEP 37.81.21.35-Gen Feb. 2012 General requirements for top tensioned riser tendon and mooring equipment for deepwater floating production systems


DEP 37.81.40.30-Gen Feb. 2012 Syntactic foam insulationfor flowlines Kopp, Frans SIEP-PTP/ADS

DEP 37.81.40.31-Gen. Feb. 2013 Welding of deepwater pipelines, flowlines and steel catenary risers (amendments/supplements to API 1104)


DEP 37.81.40.32-Gen. Feb. 2012 Automated ultrasonic inspection (AUT) of girth welds for carbon steel and CRA lined pipelines, flowlines and catenary risers


DEP 37.81.40.34-Gen Feb. 2012 Insulation for pipe-in-pipe (PIP) flowlines Kopp, Frans SIEP-PTP/ADS

DEP 37.81.40.35-Gen. Sep. 2011 Deepwater collet type connector systems Kopp, Frans SIEP-PTP/ADS

DEP 37.81.40.38-Gen. Feb. 2013 Deepwater subsea manifold system (amendments/supplements to ISO 13628-15/ API RP 17P)


DEP 37.81.40.40-Gen. Sep. 2011 External Monel clad riser pipe Guijt, Wim GSNL-PTE/EPFA


Hyperbaric welding of pipelines (amendments/supplements to ISO 13847)


DEP 37.81.41.30-Gen. Sep. 2011 (A01)

Onshore fabrication of deepwater pipelines, flowlines, risers and their appurtenances


DEP 37.81.41.33-Gen. Sep. 2011 (A01)

Offshore construction specification for deepwater pipelines, flowlines and risers


DEP 37.81.41.35-Gen. Sep. 2011 Offshore pipeline and umbilical/cable crossings Kopp, Frans SIEP-PTP/ADS

DEP 37.81.41.36-Gen. Sep. 2011 Deepwater syntactic foam insulation for subsea structures


DEP 37.81.41.37-Gen. Sep. 2011 Qualification of insulation for deepwater applications Kopp, Frans SIEP-PTP/ADS

DEP 37.81.41.40-Gen. Sep. 2012 9-5/8 inch riser threaded connector, gauging specification/quality plan








DEP 37.81.41.43-Gen. Sep. 2012 14 inch riser threaded connector, gauging specification/quality plan


DEP 37.81.42.30-Gen. Sep. 2011 Unbonded flexible pipe for offshore applications (amendments/supplements to ISO 13628-2 & ISO 13628-11)


DEP 37.81.42.31-Gen. Sep. 2011 Deepwater pipeline end terminations and midline sleds


DEP 37.81.42.34-Gen. Sep. 2011 ROV operations for work-class vehicles Kopp, Frans SIEP-PTP/ADS

DEP 37.81.42.35-Gen. Feb. 2012 Qualification of girthweld inspection with automated ultrasonic inspection (AUT) systems



Dynamically positioned (DP) vessels for construction, drilling/completions/well intervention activities - Selection and operation


DEP 37.91.10.10-Gen. Feb. 2013 Single point mooring (SPM) systems Morrison, Denby G SIEP-PTP/ADF


Mobile mooring systems (based on API RP 2SK, API RP 2SM and API RP 2I)


DEP 37.91.10.30-Gen. Feb. 2013 Mooring and berthing systems, including fenders, quick release hooks, and docking aid systems


DEP 37.91.20.30-Gen. Feb. 2013 Oil loading and discharge hoses for offshore mooring installations (amendments/supplements to OCIMF guide to manufacturing and purchasing hoses for offshore moorings (GMPHOM 2009))


DEP 37.92.10.30-Gen. Sep. 2010 Offshore pedestal-mounted cranes (amendments/supplements to API Spec 2C)


DEP 37.92.10.31-Gen. Withdrawn Pedestal cranes (amendments/supplements to Lloyd's code and BS 2573) [37.92.10.30]

DEP 38.80.10.30-Gen. Withdrawn Drilling fluid materials - Specifications and tests (Endorsement of ISO 13500)

DEP 38.80.10.31-Gen. Withdrawn Field testing of drilling fluids - Water based fluids (endorsement of ISO 10414-1)

DEP 38.80.10.32-Gen. Withdrawn Field testing of drilling fluids - Oil-based fluids (amendments/supplements to ISO 10414-2)

DEP 38.80.10.33-Gen. Withdrawn Measurement of viscous properties of completion fluids (Endorsement of ISO 13503-1)

DEP 38.80.10.34-Gen. Withdrawn Drilling fluids - Laboratory testing (Endorsement of ISO 10416)

DEP 38.80.10.35-Gen. Withdrawn Drilling and fluids materials - Drilling fluids - Processing systems evaluation (Endorsement of ISO 13501)

DEP 38.80.10.36-Gen. Withdrawn Completion fluids and materials - Testing of heavy brines (endorsement of ISO 13503-3)

DEP 38.80.10.37-Gen. Withdrawn Completion fluids and materials - Procedures for measuring the long-term conductivity of proppants (endorsement of ISO 13503-5)

DEP 38.80.10.38-Gen. Withdrawn Procedure for measuring stimulation and gravel-pack fluid leakoff under static conditions (endorsement of ISO 13503-4)

DEP 38.80.10.39-Gen. Withdrawn Completion fluids and materials - Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations (endorsement of ISO 13503-2)

DEP 38.80.20.30-Gen. Withdrawn Specifications for cements and materials for well cementing (endorsement of ISO 10426-1)

DEP 38.80.20.31-Gen. Withdrawn Testing of well cements (Endorsement of ISO 10426-2)

DEP 38.80.20.32-Gen. Withdrawn Performance testing of cementing float equipment (endorsement of ISO 10427- 3)



DEP 38.80.20.33-Gen. Withdrawn Bow-spring casing centralizers (Endorsement of ISO 10427-1)

DEP 38.80.20.34-Gen. Withdrawn Centralizer placement and stop-collar testing (Endorsement of ISO 10427-2)

DEP 38.80.20.35-Gen. Withdrawn Testing of deepwater well cement formulations (Endorsement of ISO 10426-3)

DEP 38.80.20.36-Gen. Withdrawn Determination of shrinkage and expansion of well cement formulations at atmospheric pressure (Endorsement of ISO 10426-5)

DEP 38.80.20.37-Gen. Withdrawn Preparation and testing of foamed cement slurries at atmospheric pressure (Endorsement of ISO 10426-4)

DEP 38.80.30.31-Gen. Withdrawn Drilling and production hoisting equipment (Endorsement of ISO 13535)

DEP 38.80.30.32-Gen. Withdrawn Inspection, maintenance, repair and remanufacture of hoisting equipment (Endorsement of ISO 13534)

DEP 38.80.30.33-Gen. Withdrawn Drilling and well servicing equipment (Endorsement of ISO 14693)

DEP 38.80.40.30-Gen. Withdrawn Steel drill pipe with weld-on tool joints (amendments/supplements to ISO 11961)

DEP 38.80.40.31-Gen. Withdrawn Aluminium alloy drill pipe (Endorsement of ISO 15546)

DEP 38.80.40.32-Gen. Withdrawn Marine drilling riser couplings (Endorsement of ISO 13625)

DEP 38.80.40.34-Gen. Withdrawn Rotary drilling equipment - Threading and gauging of rotary shouldered thread connections (endorsement of ISO 10424-2)

DEP 38.80.50.30-Gen. Withdrawn Drill-through equipment (Endorsement of ISO 13533)

DEP 38.80.60.30-Gen. Withdrawn Drilling and well servicing structures (Endorsement of ISO 13626)

DEP 39.01.00.10-Gen. Feb. 2013 Onshore production installations - Basic process safety systems


DEP 39.01.10.11-Gen. Feb. 2013 Selection of materials for life cycle performance (upstream facilities) - Materials selection process


DEP 39.01.10.12-Gen. Feb. 2013 Selection of materials for life cycle performance (Upstream facilities) - Equipment


DEP 39.01.10.13-Gen. Feb. 2013 Selection of materials for carbon capture and sequestration systems


DEP 39.01.10.30-Gen Feb. 2012 Specification for nickel base alloy 625 plus (UNS N07716) and alloy 725 (UNS N07725) for oil and gas drilling and production equipment



Specification of nickel base alloy 718 (UNS N07718) for oil and gas drilling and production equipment (amendments/supplements to API Standard 6A718)

Miglin, Bruce P SIEP-PTW/DCD

DEP 39.01.20.10-Gen. Withdrawn L80 13%Cr casing and tubing (amendments/supplements to ISO/DIS 11960.2)

WS 39.01.20.12-Gen. Withdrawn Casing and tubing design manual; Volume 1 - Mandatory requirements

DEP 39.01.20.30-Gen. Withdrawn Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions (endorsement of ISO 13680)

DEP 39.01.20.31-Gen. Withdrawn Care and use of casing and tubing (endorsement of ISO 10405)

DEP 39.01.20.32-Gen. Withdrawn Testing procedures for casing and tubing connections (Endorsement of ISO 13679)

DEP 39.01.20.33-Gen. Withdrawn Evaluation and testing of thread compounds for use with casing, tubing and line pipe (Endorsement of ISO 13678)

DEP 39.01.20.34-Gen. Withdrawn Field inspection of new casing, tubing and plain-end drill pipe (Endorsement of ISO 15463)



DEP 39.01.30.30-Gen. Withdrawn Wellhead and christmas tree equipment (amendments and supplements to ISO 10423)

DEP 39.01.30.31-Gen. Withdrawn Downhole equipment - Subsurface safety valves (endorsement of ISO 10432)

DEP 39.01.30.34-Gen. Withdrawn Downhole equipment - Packers and bridge plugs (Endorsement of ISO 14310)

DEP 39.01.30.35-Gen. Withdrawn Downhole equipment - Lock mandrels and landing nipples (Endorsement of ISO 16070)

DEP 39.01.30.36-Gen. Withdrawn Downhole equipment - Side-pocket mandrels (endorsement of ISO 17078-1)

DEP 39.01.30.38-Gen. Withdrawn Downhole equipment - Flow control devices for side-pocket mandrels (endorsement of ISO 17078-2)

DEP 39.01.40.30-Gen. Sep. 2012 Seawater injection facilities Sluijterman, Anton C SHLINDN-UIA/T/NOV

DEP 39.29.10.30-Gen. Withdrawn Downhole equipment - Progressive cavity pumps for artificial lift (Endorsement of ISO 15136-1)

DEP 39.29.10.31-Gen. Withdrawn Downhole equipment - Progressing cavity pumps for artificial lift - Surface-drive systems (endorsement of ISO 15136-2)

DEP 39.40.20.30-Gen. Withdrawn High pressure metal/polymer flexible pipe for use in oil and gas operations as flowlines and risers (37.80.00.30)

DEP 39.40.20.32-Gen. Sep. 2012 Elastomeric flexible elements for use in TLP tendons Morrison, Denby G SIEP-PTP/ADF

DEP 39.40.20.93-Gen. Withdrawn Metal/polymer flexible pipe

DEP 40.10.01.11-Gen. Withdrawn Capital project coding system

DEP 40.10.01.12-Gen. Feb. 2013 Polyester rope for deepwater mooring (amendments/supplements to abs guidance notes on the application of fiber rope for offshore mooring)


DEP 40.10.10.41-Gen. Withdrawn List of approved suppliers of longitudinally welded stainless pipes and tubes

DEP 40.10.21.40-Gen. Withdrawn List of approved suppliers of seamless aluminium brass condenser/cooler tubes

DEP 40.10.40.40-Gen. Withdrawn List of approved oil-resistant CAF compound jointing

DEP 40.10.40.41-Gen. Withdrawn List of approved acid-resistant CAF compound jointing

DEP 40.10.40.42-Gen. Withdrawn List of approved spiral-wound gaskets

DEP 40.10.50.41-Gen. Withdrawn List of approved suppliers of 1 Cr-0.25 Mo steel bolts and medium carbon steel nuts

DEP 40.10.64.10-Gen. Withdrawn Welding electrodes, rods wires and fluxes

DEP 40.48.00.30-Gen. Withdrawn Paints and paint materials (30.48.00.31, 70.48.10.10)

DEP 41.20.20.31-Gen. Withdrawn Purchasing procedure trays for columns (MA-13)

DEP 41.21.01.30-Gen. Withdrawn Purchasing procedure unfired shell and tube heat exchangers (MA-11)

DEP 41.21.70.31-Gen. Withdrawn Air cooled heat exchangers - purchasing procedure

DEP 41.24.49.31-Gen. Withdrawn Shop fabrication of heater piping - purchasing procedure

DEP 41.38.01.31-Gen. Withdrawn Purchasing procedure shop fabrication of steel piping (MA-05)

DEP 42.31.31.30-Gen. Withdrawn Purchasing procedure signal light assemblies

DEP 43.06.41.31-Gen. Withdrawn Electrical equipment for hoisting gear

DEP 43.65.11.31-Gen. Withdrawn Synchronous AC generators

DEP 43.65.40.31-Gen. Withdrawn Power and distr bution transformers

DEP 43.66.05.31-Gen. Withdrawn Electric motors, three-phase, aquirrel cage, induction type to 4,000 hp incl

DEP 43.66.05.32-Gen. Withdrawn Electric motors



DEP 43.67.01.31-Gen. Withdrawn AC switchboards for voltages not exceeding 1000 V

DEP 43.67.51.31-Gen. Withdrawn HT switchboards

DEP 44.24.32.30-Gen. Sep. 2012 Unshaped refractory materials for monolithic refractory linings


DEP 44.24.32.31-Gen. Sep. 2012 Classification of unshaped refractory lining materials Yuen, Simon SCAI-PTE/AMMI

DEP 44.24.32.32-Gen. Sep. 2012 Specification for sampling and testing of unshaped refractory lining materials


DEP 44.24.32.33-Gen. Sep. 2012 Specification for anchoring systems of unshaped refractory lining materials


DEP 44.24.90.31-Gen. Feb. 2012 Refractory bricks and shapes Yuen, Simon SCAI-PTE/AMMI

DEP 44.24.90.32-Gen. Feb. 2012 Classification of refractory bricks and shapes Yuen, Simon SCAI-PTE/AMMI

DEP 44.24.90.33-Gen. Feb. 2012 Specification for sampling and testing of refractory bricks and shapes


DEP 44.24.90.34-Gen. Feb. 2012 Classification, specification and testing for ancillary materials for refractory brick construction


DEP 44.24.90.35-Gen. Feb. 2012 Specification and quality control for precast or specialty cast refractory baffle wall tile (shapes)


DEP 44.28.00.31-Gen. Withdrawn Purchasing procedures steel structures (MA-12)

DEP 44.51.01.31-Gen. Withdrawn Purchasing procedure standard vertical tanks (MA-07)

DEP 52.54.80.10-Gen. Withdrawn Guidelines for starting-up fired equipment

DEP 60.00.10.13-Gen Feb .2012 Mobile crane foundation assessment Kruijsen, Ton ATJJM GSNL-PTE/ECSO

DEP 61.10.08.11-Gen. Feb. 2011 Field inspection prior to commissioning of mechanical equipment


DEP 61.22.01.31-Gen. Withdrawn Rotating disc contactors - Installation, site testing and maintenance (31.22.01.31)

DEP 61.24.15.31-Gen. Withdrawn SIPM-type vertical furnaces and waste heat boilers - Field erection

DEP 61.38.10.10-Gen. Feb. 2013 Shop and field fabrication of orifice meter runs Kruijer, Alfred A GSNL-PTE/EMMI


Welding of pipelines and related facilities(amendments/supplements to ISO 13847:2000)



Field welding of duplex and super duplex stainless steel pipelines (amendments/supplements to API 1104)


DEP 61.40.20.36-Gen. Feb. 2012 (A01)

Welding of CRA-CLAD or CRA-LINED pipe materials (amendments/supplements to API 1104:20th edition)


DEP 62.10.08.11-Gen. Feb. 2013 Inspection and functional testing of instruments Mooi, Peter GSNL-PTE/EPAC

DEP 62.10.09.11-Gen. Withdrawn Factory inspection and testing of instruments and instrument systems (62.10.08.11)

DEP 62.37.10.12-Gen. Withdrawn Instrument installation procedures

DEP 63.10.08.11-Gen. Sep. 2011 Field commissioning of electrical installations and equipment


DEP 63.10.08.14-Gen. Feb. 2012 Field commissioning and testing of electrical installations and equipment for North American application


RMP 63.10.08.50-Gen. Sep. 2011 Maintenance of electrical installations and equipment


DEP 63.20.08.10-Gen. Sep. 2012 (A01)

Electrical installation for North American application Barrios, Louis A GSUSI-PTE/AELE

DEP 64.11.10.31-Gen. Withdrawn Site preparation (34.11.00.11)


Refractory linings for sulphur recovery units (Claus and SCOT)




DEP 64.24.32.12-Gen. Sep. 2012 Refractory lining for fluidized catalytic cracking unit (FCCU)

Chakrabarti, Sujit PTIN-PTE/PMMI

DEP 64.24.32.30-Gen. Withdrawn Insulating and dense refractory concrete linings

DEP 64.24.32.31-Gen. Feb. 2012 Construction details for refractory brick and shape construction


DEP 64.24.32.33-Gen. Sep. 2012 Guidelines for curing, drying and firing of unshaped refractory lining materials


DEP 64.24.32.34-Gen. Sep. 2012 Refractory contractor selection and applicator qualification for installation of unshaped refractory lining materials


DEP 64.24.32.35-Gen. Sep. 2012 Construction design details of unshaped refractory materials


DEP 64.51.01.31-Gen. Withdrawn Vertical tanks - Erection and testing (based on EN 14015)

DEP 70.00.00.10-Gen. Withdrawn Collection and exchange of reliability and maintenance data for equipment (endorsement of ISO 14224)

DEP 70.07.20.30-Gen. Withdrawn Magnetic particle inspection of the threaded parts of steel drill stem

DEP 70.08.10.10-Gen. Withdrawn Equipment and tools for maintenance and inspection. Part 1: - Inspection Tools and NDT instruments

DEP 70.08.10.11-Gen. Feb. 2013 Mechanical and electrical maintenance equipment and tools

Bitter, Peter C GSNL-PTE/EOEX

DEP 70.08.10.12-Gen. Withdrawn Equipment and tools for maintenance and inspection. Part 3: - Mechanical maintenance - Tools (70.08.10.11)

DEP 70.08.10.13-Gen. Withdrawn Electrical workshop - Test equipment and tools

DEP 70.08.10.14-Gen. Withdrawn Equipment and tools for maintenance and inspection. Part 5: - Instrument technical centre and workshop - Equipment and tools

DEP 70.10.01.10-Gen. Withdrawn Equipment record cards

DEP 70.10.01.30-Gen. Withdrawn Equipment record cards

DEP 70.10.70.11-Gen. Feb. 2011 Preservation of new and old equipment standing idle van Ro j, Johan FM GSNL-PTE/EMMI

RMP 70.10.70.50-Gen. Feb. 2011 Preservation of new and old equipment standing idle Mead, Hearl E GSUSI-PTE/AMMI

DEP 70.10.80.11-Gen. Withdrawn Cleaning of equipment

DEP 70.10.90.11-Gen. Feb-2012 Spare parts Roberts, Jason M GSUK-PTE/EOEX

DEP 70.48.10.10-Gen. Withdrawn Maintenance painting (30.48.00.31)

DEP 70.48.11.30-Gen. Withdrawn Protective coatings for offshore facilities

DEP 70.51.10.11-Gen. Withdrawn Field inspection, maintenance and repair of vertical steel storage tanks

RMP 70.51.10.50-Gen. Sep. 2011 Field inspection, maintenance and repair of vertical steel storage tanks (amendments/supplements to API 653 and EEMUA159)


DEP 74.00.10.10-Gen. Feb. 2012 Shop and field pressure testing of piping systems Kruijer, Alfred A GSNL-PTE/EMMI

DEP 74.04.12.15-Gen. Withdrawn Testing methods for stored cat. cracker refractories

DEP 74.36.10.31-Gen. Withdrawn Testing of soft seat ball valves designed in accordance with BS 5351

DEP 74.36.10.32-Gen. Withdrawn Design and evaluation of rubber lined butterfly valves for fire protection service

DEP 80.00.00.15-Gen. Feb. 2013 Hazard and operability (HAZOP) study Salter, Natalie Y GSUSI-PTE/DAPP

DEP 80.00.10.10-Gen. Feb. 2013 Area classification (amendments/supplements to IP 15)


DEP 80.00.10.11-Gen. Feb. 2013 Layout of onshore facilities Kruijsen, Ton ATJJM GSNL-PTE/ECSO




Layout of offshore facilities Morrison, Denby G SIEP-PTP/ADF

DEP 80.00.10.13-Gen. Feb. 2013 Area classification and electrical equipment spacing for North American application


DEP 80.10.10.31-Gen. Sep. 2012 Breathing air and supply systems Salter, Natalie Y GSUSI-PTE/DAPP

DEP 80.36.00.30-Gen. Feb. 2012 (A01)

Relief devices - Selection, sizing and specification Kruijer, Alfred A GSNL-PTE/EMMI

DEP 80.45.10.10-Gen. Feb. 2012 (A01)

Design of pressure relief, flare and vent systems Kruijer, Alfred A GSNL-PTE/EMMI

DEP 80.45.10.11-Gen. Feb. 2012 Overpressure and underpressure - Prevention and protection


DEP 80.45.10.12-Gen. Feb. 2011 (Sep. 2011 Circ.; Feb. 2012 Circ.; A03)

Emergency depressuring and sectionalizing Salter, Natalie Y GSUSI-PTE/DAPP

DEP 80.45.10.13-Gen. Sep. 2012 Alternative pressure relief design for assessment of existing facilities



Flare details (amendments/supplements to ISO 25457)



Interlocking systems for pressure relief valves Kruijer, Alfred A GSNL-PTE/EMMI

DEP 80.47.10.10-Gen. Withdrawn Fire-fighting agents (80.47.10.32)

DEP 80.47.10.11-Gen. Withdrawn Fire-fighting systems (80.47.10.30)


Water-based fire protection systems for offshore facilities


DEP 80.47.10.30-Gen. Feb. 2013 Assessment of the fire safety of onshore installations Salter, Natalie Y GSUSI-PTE/DAPP


Active fire protection systems and equipment for onshore facilities


DEP 80.47.10.32-Gen. Sep. 2011 Fire-fighting agents and portable/mobile fire fighting equipment for onshore applications


DEP 80.47.10.33-Gen. Feb. 2012 (A01)

Fire-fighting vehicles and fire stations Salter, Natalie Y GSUSI-PTE/DAPP

DEP 80.47.20.30-Gen. Withdrawn Trucks and trailers for fire-fighting (80.47.10.33)

DEP 80.64.10.10-Gen. Feb. 2011 Electrical safety rules de Wilt, Wim GSNL-PTE/EELE

DEP 80.64.10.11-Gen. Feb. 2013 Static electricity Donnellan, Paul J GSNL-PTE/EELE

DEP 80.80.00.10-Gen. Feb. 2013 Lifeboats and rescue boats (amendments/supplements to SOLAS, LSA and DNV-OS-E406)


DEP 80.80.00.11-Gen. Feb. 2011 Control and mitigation of fires and explosions on offshore production installations (amendments/supplements to ISO 13702:1999)


DEP 80.80.00.12-Gen. Feb. 2011 Offshore production installations - Requirements and guidelines for emergency response (amendments/supplements to ISO 15544:2000)




DEP 80.80.00.13-Gen. Sep. 2002 Offshore production installations - Guidelines on tools and techniques for identification and assessment of hazardous events (amendments/supplements to ISO 17776)


DEP 80.80.00.14-Gen. Feb. 2013 Offshore facilities life-saving appliance requirements Rhodes, Terry C SUKEP-UIE/T/PE

DEP 82.00.10.10-Gen. Feb. 2012 Project quality assurance Arnold, Gregory C GSUSI-PTE/AQIP

DEP 82.00.10.11-Gen. Withdrawn Cost Control Of Capital Investment Projects (Project Guide No. 6, OG.03.307.48)

DEP 82.00.10.12-Gen. Feb. 2011 Life cycle costing (endorsement of ISO 15663-1) Brown, Dave A SIEP-PTE/SCDM

DEP 82.00.10.30-Gen. Feb. 2012 (A01)

Engineering information specification (EIS) Festen, Maarten M GSNL-PTE/EOEX

DEP 91.00.00.10-Gen. Withdrawn Sector-specific quality management systems - Requirements for product and service supply organizations (Endorsement of ISO/TS 29001)



PART IV REFERENCES

In this DEP, reference is made to the following publications: NOTES: 1. Unless specifically designated by date, the latest edition of each publication shall be used,

together with any amendments/supplements/revisions thereto.

2. The DEPs and most referenced external standards are available to Shell staff on the SWW (Shell Wide Web) at http://sww.shell.com/standards/.

SHELL STANDARDS

DEP feedback form DEP 00.00.05.80-Gen.

Standard drawings index DEP 00.00.06.06-Gen

Standard forms index DEP 00.00.10.05-Gen.

Requisitions index DEP 30.10.01.10-Gen.


http://sww.shell.com/standards/

DEP-00.00.05.05-GEN

Documents

Transcript of DEP-00.00.05.05-GEN