OPERATING INSTRUCTIONS

IMPORTANT

This manual provides operating instructions for the CLESTA-II. The instructions contained in this booklet should be thoroughly read and

understood before operating the unit and chair. After the installation has been completed, keep this manual in a safe place

and refer to it for future maintenance.

DENTAL UNIT

0197

If you have any questions about this Manual or this product, please contact us. If manual becomes unreadable or is lost, please request a new manual by contacting your dealer. Installation should be conducted by authorized personnel only. Follow instructions on installation manual.

Page 1.OVERALLVIEWANDMAJORCOMPONENTS------------------------ 1

2.DIMENSIONSANDSPECIFICATIONS 2-1.DIMENSIONS------------------------------------------------------------- 1 2-2.SPECIFICATIONS-------------------------------------------------------- 1

3.OPERATINGINSTRUCTIONS 3-1.DOCTORTABLESECTION-------------------------------------------- 2 3-2.CUSPIDORUNITSECTION-------------------------------------------- 10 3-3.FOOTCONTROLSECTION-------------------------------------------- 12

4.SAFETYLOCKDEVICE-----------------------------------------------------13

5.CAREANDMAINTENANCE------------------------------------------------ 14

6.ELECTROMAGNETICCOMPATIBILITY(EMC)--------------------------- 16

7.LISTOFCOMPATIBLEHANDPIECES-------------------------------------- 19

TABLE OF CONTENTS

IntendedUseoftheProduct

Thisproductisanactivetherapeuticdeviceintendedfortheexclusiveusefordiagnoses,

treatmentsandrelativeproceduresofdentistry.

The product must be operated or handled by the qualified dentists or by dental staffs under thesupervisionofthedentist.Suchdentistsordentalstaffsshouldinstructand/orassistthepatientstoapproachtoandleavefromtheproduct.Patientsshouldnotbeallowedtooperateorhandletheproductunlesshe/sheissoinstructed.Theproductissuppliedtogetherwiththehandpieceslikeelectricmicromotor,airturbineand/ormotor,scalerandsoon.

EnvironmentalRequirementsAmbientTemperatureOperating+5 -+40　Storage-10　-+50Humidity10%-80%AtmosphericalPressure600hPa-1060hPa

℃℃ ℃ ℃

CompatibilityofHandpieces

Usethecompatiblehandpiecesasshownontheattachedlistforthisunit.(Listofcompatible

handpieces).

ImportantNotes

In case of the troubles, please contact Takara Belmont offices or your dealers.

Donotdisassembleorattempttorepair.

Disassembly, repair or modifications shoud only be done by a qualified repair technician.

Attempts at disassembly, repair or modifications may lead to abnormal operation and accidents.

Incaseofdisposalofequipment

Incaseofdisposalofequipmentorofcomponentsdismountedfromtheunit,takefullinfection

preventingmeasures,andcarryoutappropriatestepsinaccordancewiththelegalregulations

atthattime.

Ｗ Ａ

EC REP

SN

MANUAL SENSOR

Chair last position Chair auto return Chair preset1 Chair preset2

To raise the chair To lower the chairTo Recline the backrest

To raise the backrest

Chair last position

Chair manual control Chair auto control

To lower the chair

Handpiece coolant spray on/off

Fiber optic handpiece lighton//off

Micro motor Forward/Reverseselect

Syringe Dental light on/off

Dental lightmode selection

Service outletwater flow control

Service outlet (water)

Service outlet (air)

Water heater

Air

Non-ionizingradiation

Authorizedrepresentative inthe European community

Separatecollection for electrical and electronicequipment

Type B Applied Parts

CautionIt means “caution, warnings, or possibility to danger”.

Chair auto return Chair preset1

To Recline the backrest

To raise the backrest

Chair preset2

Chair manual control

Handpiece Setting

Rotation mode select

Minus Plus

Water

Function Store

Bowl flush Cupfiller

Rotation speedcontol

Date of manufactureManufacturer

Protective earth (ground) ON (power) OFF (power)

Scalerpower control

Serial number

alternating current

Refer to operating instructions

To raise the chair

SYMBOLS

Inthismanual,onthelabelsoronthecontrolpanelofCLESTAII,followingsymbolsareused.Confirm the meaning of each symbol.

1. OVERALL VIEW AND MAJOR COMPONENTS

SalivaEjectorHandpiece

AssistantHolderArm

CuspidorTop

CuspidorBody

LightPole

FirstArm(HorizontalArm)

BalanceArm

InstrumentTray

MainControlPanel

Dr.TableIndicator

TrayHandle(WithArmAirBrakeButton)

Dr.SideHandpieceHolder

Dr.SideSyringe

WasteReceptacle

FilmViewer

FootController

DentalLight

Handpieces

(Micromotor,AirTurbine/Motor,Scalerandetc.)

Manufacturersrecommendtousethehandpieces

withCEmarkings)

Fig.1-1OverallViewandMajorComponents

-1-

LP

21 0

F

W A

14

1526

16

24

17

191821

22

25 23

20

12

34

78

910

11

12

135

6W

A

27

Cupfiller Nozzle

Cupfiller Base

BowlFlushNozzle

SpittoonBowl

SolidCollector

CuspidorUnitControlPanel

AssistantHolder

(WithMembraneSwitch)

VacuumHandpiece

AssistantSideSyringe

2. DIMENSIONS AND SPECIFICATIONS -mm-

NetWeight-------------94.7kg(WithoutDentalLight)ServiceLife------------10years

Fig.2-1Dimensions

29959

8

290˚340˚

700

30˚ 30˚740

562

30˚

°16˚33˚

50˚90˚

1282

891

274

90˚

517

90˚

90˚

138˚

55˚ 439

184

56960

60.5

651

489

737

ø42.7

222 600

750187

9

13

1112

1516

10

8

14

7

2

6

1

43

5

18

22

2617

23

21

25

27

20

24

19

Fig.3-1MasterSwitch

ON OFF

Master Switch

Fig.3-4 Cupfiller Switch

Turnoffthemasterswitchafterdailyoperationandforlongterminterval.

3. OPERATING INSTRUCTIONS3-1.DOCTORTABLESECTION

(1)MasterSwitch(Fig.3-1,Fig.3-2&Fig.3-3)Turnonthemasterswitchlocatedundertherighthandsideofthedoctortable,thepowerindicatoronthemaincontrolpanelwillthenilluminategreen.(Fig.3-2&3-3)

LOCK

3 2

MAIN

1

47

56

LP

21

0

(2)MainControlPanelASpec.ControlPanel

Cupfiller Switch (Fig.3-4) Momentarily press the cupfiller switch ( ), water will come out fromthe cupfiller nozzle for 3 seconds and stops automatically. Also the bowl flush starts and will run for 6 seconds and stops automatically.While the cupfiller is working, by momentarily pressing the cupfiller switch ( ) the cupfilling will cancel.Also, when the cupfiller starts, the spittoon water flushes 6 secondsandstopsautomatically.(SynchronizedBowlFlush) Note : The cupfiller water volume can be adjusted by the cupfiller flow control knob located insidethecuspidorbody.Referto3-2.(3).

A E

1

1

7

3

48 12 15 6 2

9 1310 14 6

16

5 11

Fig.3-3ESpec.MainControlPanel

72

6

1

4

3

5

13

11

12

15

1610

14

9

8

PowerIndicatorCupfiller SwitchBowlFlushSwitchLightPackSwitchChairManualControlSwitchesChairAutoModeSwitches

DecreasingSwitchIncreasingSwitchStoreSwitchFunctionIndicator

Fig.3-2ASpec.MainControlPanel

BowlFlushSwitch(Fig.3-5)Momentarily press the bowl flush switch ( ), water flushes for 6 secondsand stops automatically. (Timer Mode) Press the bowl flush switch for 2 seconds, water flushes continuously. (Continuous mode)While the bowl flush is working by momentarily pressingthe bowl flush switch ( ) the bowl flush will stop. Note 2 : Clesta-2 unit can be set to timer mode (standard setting) and continuius mode for bowl flush. The bowl flush water volume can be adjusted by the bowl flush flow control knob located insidethecuspidorbody.Referto3-2.(3).

Fig.3-5BowlFlushSwitch

A E

SafetyLockIndicatorCoolantWaterON/OFFSwitchElectricMotorSpeedSettingSwitchElectricMotorDirectionControlSwitchDentalLightSwitchFunctionSwitch

Fig.3-6LightPackSwitch

LED

A ETheLightPackSwitch(Optional)(Fig.3-6)Pick up the fiber optic handpiece from the holder, momentarily pressthelightpackswitch(),theindicatorilluminatesingreenand the fiber optic power turns on. Toswitchoffthelightpacksimplypressthelightpackswitchagain.

ESpec.ControlPanel

2

3

4

ＥＡ

ＥＡ

ＥＡ

-2-

ＥＡ ＥＡ

-3-

Fig.3-7ChairManualControlSwitches

A E

Fig.3-8ChairAutoModeSwitches

LP

21

0

A E

ChairManualControlSwitches(Fig.3-7)a.SeatLifting-------------Pressthe()switchuntiltheseatislifteduptothedesiredposition.b.SeatLowering---------Pressthe()switchuntiltheseatisloweredtothedesiredposition.c.BackrestReclining----Pressthe()switchuntilthebackrestisreclinedtothedesiredposition.d.BackrestRaising------Pressthe()switchuntilthebackrestisraiseduptothedesiredposition.

b.AutoReturnOperationMomentarilypresstheautoreturnswitch( 0 ),thechairreturnstotheinitialposition(theseatisthelowestpositionandthebackrestistheuprightposition)andstopsautomatically.c.LastPositionMemoryOperationMomentarilypressthelastpositionmemoryswitch( LP )atthetreatmentposition,thebackrestraisesuptotherinsingposition(uprightposition)andstopsautomatically.Momentarilypressthelastpositionmemoryswitch( LP )again,thebackrestreturnstotheprevioustreatmentpositionandstopsautomatically.d.EmergencyStop(SafetyStop)Duringautomaticmovements(preset,autoreturnandlastpositionmemory),bymomentarilypressinganychaircontrolswitchthiswillcanceltheautomaticmovementimmediately.

SafetyLockIndicator(Fig.3-9)Thesafetylockindicatorilluminatesumberwhenthesafetylockdeviceisworking.Note:Pleaserefertopage134.SafetyLockDevice.

CoolantWaterON/OFFSwitch(Fig.3-10)Whenahandpieceispickedupandthisswitchispressed,bothLEDA(air)andLEDW(water)lightsup,thecoolantwaterandaircomesoutfromthehandpiece.Incaseofairmotororairturbine,switchingbetweenspray(bothofLEDAandLEDWarelit)andOFFoccurswhenthisswitchispressed.Incaseofelectricscaler,switchingbetweenwateronly(LEDWislit)andOFFoccurswhenthisswitchispressed,regardlessofthemode.Incaseofmicromotor,eitherthe2-modeorthe4-modecanbeselectedbymodeselectsetup.Whenthisswitchispressedinthe2-modesetup,switchingbetweensprayandOFFoccurs.Incaseof4-modesetup,switchingoccursinthesequenceindicatedbeloweachtimewhenthisswitchispressed:SpraytoWateronlytoAironlytoOFF

Fig.3-10CoolantWaterON/OFFSwitch

ChairAutoModeSwitches(Fig.3-8)a.PresetOperationMomentarilypressthepreset-1switch( 1 ),thechairmovestothepreset1positionandstopsautomatically.Preset2positionoperatedbythepresetswitch( 2 ).Note:ForpresetpositionadjustmentrefertochairManual.

8

7

6

5 ＥＡ

ＥＡ

ＥＡ

ＥＡ

Fig.3-9SafetyLockIndicator

LOCKLED

Fig.3-11ElectricMotorSpeedSetSwitch

1)Switchingtolimitrotationspeed(limitmode)Pickupthemicromotorfromtheholder,andpressthisswitch()toselectlimitmode.Forselectingtheupperlimitinthelimitmode,presseitherplus()switchorminus()switch.Theupperlimitofthemicromotorrotationspeedchangesinthreesteps(or5steps).-Upperlimitofrotationspeedincaseof3steps:10000/20000/40000min-1(rpm)-Upperlimitofrotationspeedincaseof5steps:5000/10000/20000/30000/40000min-1(rpm)Seeitemg.onpage7forsettingin5steps.Themicromotorrotationspeedcanbevariedintherangeofuptotheselectedupperlimitbyslidingthefootcontrollerpedalrightorleft.Therotationspeedrangevariesbythemicromotortype.

2)Switchingtopresetrotationspeed(presetmode)Pickupthemicromotoroutoftheholder,pressthisswitch(),andthenselectpresetmode(SET1to3).Therotationspeedinthismodecanbechangedbypressingplus()switchorminus()switch.Pressstoreswitch()forstoringthechangedrotationspeed.Whenthefootcontrollerisdepresseduponselectionofpresetmode(SET1to3),themicromotorrunsatthefixed rotation speed indicated on the indicator.

-4-

ElectricMotorSpeedSetSwitch(Optional)(Fig.3-11)Twodifferentmodes,limitmodeandpresetmode,areavailableasmicromotorrotationspeedmodes.Pressingthisswitcheachtimechangesthespeedmode:Limitspeed->SET1->SET2->SET3->Limitspeed.Theindicatorindicatestheselectedmode.

Green LED(Forward Rotaition)

Amber LED(Reverse Rotation)

ElectricMotorRotationDirectionControlSwitch(Optional)(Fig.3-12)Afterpickinguptheelectricmotorfromtheholder,theelectricmotorrotationdirectioncanbechangedbymomentarilypressingthisswitch()therotationdirectionwillbeindicatedbytheamberandgreenLEDs.Indicatoringreen:ForwardRotationIndicatorinamber:ReverseRotationNote:Donotchangetheelectricmotordirectionwhilethemotorisrunning.WhentheelectricmotorwithsettingReverseRotationisreturnedtheholderandpickedupagain,abuzzersounds.

Fig.3-12ElectricMotorDirectionControlSwitch

DentalLightON/OFFSwitch(Fig.3-13)Switchforon/offthedentallight.

FunctionSwitch(Fig.3-14)Usethisswitchforsettingvariousworkingconditions.Asforthesetupprocedures,pleasereferto3-1.(3)a-i.

9

11

12

10

ＥＡ

ＥＡ

ＥＡ

ＥＡ

Fig.3-13DentalLightON/OFFSwitch

Fig.3-14FunctionSwitch

+

+

(3)FunctionSwicthSetupProcedure

b.GroupSelectionModeThegroupselectionmodeisaconvenientfunctionforthedentalclinicwhereamultiple(uptofourgroups)ofdentistsworkwithoneunit.Thefollowingfunctionscanbesetforeachgroup.Presetpositionforchair.Presetrotationspeedformicromotor.Tosetthegroup.1)Momentarilypressthefunctionswitchtwiceonmaincontrolpanel,andthefunctionindicatorwillindicategroupnumber.2)Momentarilypressthe0,1,2orLPswitchonmaincontrolpaneltosetoneof4group.0;Group1/1;Group2/2;Group3/LP;Group4

FunctionSwitch 0Switch 1Switch 2Switch LPSwitch

1)TosetatimerMomentarilypressthefunctionswitch,andsetthetimebypressingdecreaseswitchandincreaseswitch.　　　…Minimumsettingtimebyswitchis10seconds.　　　…Minimumsettingtimebyswitchis1minute.Thesettingtimeisindicatedonthefunctionindicator.Momentarilypressthestartswitchtostarttimer.Theendofsettingtimeisinformedbyelectronicsounds.Example:Settingtime3minutes30secondsisindicatedas03:30inthefunctionindicator.

a.TimerTimercanbesetmaximum90mins.50secs.in10secs.segment.

FunctionSwitch DecreaseSwitch IncreaseSwitch

-5-

+

0 1 2 LP

StartSwitch(ElectricMotorSpeedSettingSwitch)

+

Fourpresettimecanbeset.(0)(1)(2)(LP)Momentarilypressfunctionswitch,andsetthetimebypressingdecreaseswitchandincreaseswitch.Pressthestoreswitch,thenpressthe(0)(1)(2)or(LP)switchtostoreinmemory.

0Switch 1Switch 2Switch LPSwitch

0 1 2 LP

2)Presettimesetting

StoreSwitchFunctionSwitch DecreaseSwitch IncreaseSwitch

+

3)Presettimeoperation

4)Cancelthetimerduringtimecountdown

0Switch 1Switch 2Switch LPSwitch

0 1 2 LPFunctionSwitch StartSwitch

(ElectricMotorSpeedSettingSwitch)Pressthefunctionswitch,thenpressthe(0)(1)(2)or(LP)switchtochoosedesiredpresetnumber.Pressstartswitchtostarttimer.

Momentarilypressfunctionswitch,thenpressstartswitchtocanceltimer.

FunctionSwitch StartSwitch(ElectricMotorSpeedSettingSwitch)

ＥＡ

1) Short time flush outMomentarilypressthefunctionswitchthreetimesandmomentarilypressthedecreaseswitch.Pickupthehandpiecesfromtheholderandsettheminthecuspidorbowl. By momentarily pressing the foot controller this starts short time flush out.Watercomesoutfromthehandpieceandstopsautomaticallyafter40seconds. During flush out, by momentarily pressing any one of unit control switch or foot controller will cancel flush out immediately. 2) Long time flush outMomentarilypressthefunctionswitchthreetimesandmomentarilypresstheincreaseswitch.Pickupthehandpiecesfromtheholderandsettheminthecuspidorbowl. By momentarily pressing the foot controller this starts long time flush out for 5 minutes. Then, cupfiller and bowl flush out starts and stops automatically in another 5 minutes. During flush out, momentarily pressing the any one of unit control switch or foot controller will cancel flush out immediately.

c.Flushoutsystem(Optional) The CLESTA II is equipped with two types of flush out system. Short time flush out is for cleaning handpiece water lines. Long time flush out is for handpiece water lines, bowl flush water line and cupfiller water line.

FunctionSwitch DecreaseSwitch IncreaseSwitch+

e.Fiberoptichandpiecelightingmode(Optional) In case that fiber optic handpiece is installed, the fiber optic turns on when the handpiece is taken out of theholder,andturnsoffwhenthehandpieceisreturnedtotheholder. This could be changed to fiber optic turns on when the handpiece is taken out of the holder and drive air pedaloffootcontrolisactivated.

Momentarily press the function switch five times and press the decrease switch.Toreturntooriginalsetting. Momentarily press the function switch five times and press the increase switch.

FunctionSwitch DecreaseSwitch IncreaseSwitch

d.Controlpanelswitchingsoundon/offPressingaswitchonthecontrolpanelmakesanelectronicsound.Thissoundcanbeeliminatedasfollows;

Momentarilypressthefunctionswitchfourtimesandmomentarilypressthedecreaseswitch.Toreturntooriginalsetting.Momentarilypressthefunctionswitchfourtimesandmomentarilypresstheincreaseswitch.

FunctionSwitch DecreaseSwitch IncreaseSwitch+

+

-6-

g.Micromotormaximumspeedsetting(Optional)

Themaximumrotationspeedofthemicromotorcanbeselectedin3steps(10000,20000,40000min-1(rpm)).Thisfunctioncanbechangedto5steps(5000,10000,20000,30000,40000min-1(rpm))asfollows:

Momentarilypressthefunctionswitchseventimesandpresstheincreaseswitch.Toreturntooriginalsetting.Momentarilypressthefunctionswitchseventimesandpressthedecreaseswitch.

FunctionSwitch DecreaseSwitch IncreaseSwitch+

-7-

Momentarilypressthefunctionswitchsixtimes. Momentarilypressoneofchairautomodeswitch(0,1,2,LP)thenthenewelectronicsoundistobememorized.

f.ElectronicsoundfortimerElectronicsoundfortimercanbechanged.

FunctionSwitch ChairAutoModeSwitch

0 2 LP1

h.CoolantWaterON/OFFSwitchIncaseofmicromotor,eitherthe2-modeorthe4-modecanbeselectedbymodeselectsetup.Whenthisswitchispressedinthe2-modesetup,switchingbetweensprayandOFFoccurs.Incaseof4-modesetup,switchingoccursinthesequenceindicatedbeloweachtimewhenthisswitchispressed:SpraytoWateronlytoAironlytoOFF

Toset2modeMomentarilypressthefunctionswitcheighttimesandpressthedecreaseswitch.Toset4modeMomentarilypressthefunctionswitcheighttimesandpresstheincreaseswitch.

+FunctionSwitch DecreaseSwitch IncreaseSwitch CoolantWater

ON/OFFSwitch

i. Cupfiller and bowl flush Cupfiller and bowl flush are set to operate together (when the cupfiller switch is activated, bowl flushalsostarts).Tomaketheseoperateindependently.

Momentarilypressthefunctionswitchninetimesandpressthedecreaseswitch.Toreturntooriginalsetting.Momentarilypressthefunctionswitchninetimesandpresstheincreaseswitch.

FunctionSwitch DecreaseSwitch IncreaseSwitch+

(5)DoctorTableSectionControlKnobsA.HandpieceSprayWaterControlKnobs(Fig.3-15)Thehandpiecespraywatercontrolknobsarelocatedunderthedoctortable.Eachhandpiecespraywatercontrolknobismarked1-4fromtheleftsideHP1,HP2,HP3,...Thehandpiecespraywatervolumecanbecontrolledindependently.*TheHP4isoptional.

B.Doctor'sSyringeFlowControlKnobs(Fig.3-15) Doctor's syringe flow control knobs are located onthefacingrightsideunderthedoctortable. The flow control knobs adjust the doctor's syringe air and water flow volume. The yellow capped knob is the air flow control knob, the blue capped knob is the water flow control knob.

Note:Turningthecontrolknobcounterclockwisewill increase the flow volume and turning clockwisewilldecrease.(Fig.3-16)

(4)ScalerforSATELECSP4055(Optional)Thesettingrangeofultrasonicscalercanbeselectedin3ranges(Scaling,prosthesisremoval,amalgam,plugging/Ultrasonicendodontictreatment/Ultrasonicperiodontaltreatment).Pickupthehandpieceofscalerandsettherangebypressingincreaseswitchordecreaseswitch.

Fig.3-15DoctorTableSectionControlKnobs

Fig.3-16ControlKnob

Increase Decrease(Stop)

Doctor's Syringe Flow Control Knobs

Handpiece Spray Water Control Knob

HP1HP2

HP3HP4

(Opti

onal)

Syring

e

-8-

(6)HandpiecePressureGauge(Fig.3-17)Handpiecedriveairpressuregaugeislocatedontherearsideofthedoctortable.Whileahandpieceisworking,thehandpiecedriveairpressureisindicatedonthehandpiecepressuregauge. 1

2 3

4

5

Handpiece Drive Air Pressure Gauge

Fig.3-17HandpiecePressureGauge

-9-

(7)BalanceArmAirBrake(Fig.3-18)Balancearmairbrakebuttonislocatedonthehandle.WhenthemasterswitchisON,thebalancearmislocked.Graspthehandleandpresstheairbrakebuttontoadjustthetableheight.Releasetheairbrakebuttonatthedesiredtableposition,thebalancearmislocked.

Fig.3-18BalanceArmAirBrake

LP

21 0

F

Air Brake Button

Balance Arm

Note:Donotloadover1.5kgonthetable.

(8)DentalSizeFilmViewer(Fig.3-19)FilmviewerON/OFFswitchislocatedrightsideof the film viewer. Press the switch, the film viewer turns on. Press again, the film viewer turns off.

Film ViewerON/OFF Switch

Fig.3-19DentalSizeFilmViewer

Fig.3-20PanoramaSizeFilmViewer

Film ViewerON/OFF Switch

Film Viewer Dimmer

ONOFF

Bright

Dark

HolderSupportArm/HndpieceHolder(Fig.3-21)Donotadjusttheholdersupportarmandhandpieceholder. Because the angle adjustment of the holder is fixed at thepointofinstallation,theholdersupportarmwillbedamagedincaseitismovedtoohard.

CAUTION

Handpieces

Refertohandpiecemanufacturersoperatinginstructions.

CAUTION

(9)PanoramaSizeFilmViewer(Optional)(Fig.3-20) Film viewer ON/OFF switch and film viewer dimmer are located on the right side of the film viewer. Film viewer brightness can be adjusted by the film viewerinstensitycontrolwheel.

Fig.3-21HolderSupportArm/HndpieceHolder

Fig.3-22AssistantSideControlPanelandCuspidorUnitControlPanel

-10-

(1)AssistantSideControlPanel(Fig.3-22) Cupfiller switch, bowl flush switch, dental light switch and chair auto mode switches are located ontheassistantsidecontrolpanel.Referto3-1.(2),,,&.(2)CuspidorUnitControlPanel(Fig.3-22)A.DentalLighta.IO5000DentalLightDentallightcanbeoperated(ON/OFF)eitherbythetouchlessswitchlocatedonthelighthead,orbythemanualswitchonthecuspidorunitcontrolpanel.Tooperatebythetouchlessswitch------------SettheswitchlevertoLeftside(SENSORSide)Tooperatemanually-----------------------------SettheswitchlevertoRightside(ManualSide) SettheswitchlevertoCentreforOFF.

B.WaterHeaterSwitch(Fig.3-22) Waterheaterswitchislocatedonthecuspidorunitcontrolpanel. Turn on the water heater switch, and the cupfiller water will warm up.

C.ServiceWaterOutlet(Fig.3-22) Theservicewateroutletprovidesaquick-connectionforwater.

D.ServiceWaterOutletControlKnob(Fig.3-22) Thewatervolumefromtheservicewateroutletcanbeadjustedbytheservicewateroutletcontrolknob. Turning the knob counterclockwise will increase the flow volume and turning clockwise will decrease.E.ServiceAirOutlet(Optional)(Fig,3-22) Serviceairoutletprovidesaquick-connectionforair.

3-2.CUSPIDORUNITSECTION

Water HeaterSwitch

Service WaterOutlet

Service WaterControl Knob

Service AirOutlet

Dental Light ModeSelection Switch(for IO5000)

Cupfiller Switch

Dental Light switch (for E Type)

Chair Auto ModeSwitches

Bowl Flush Switch

Assistant Side Control Panel

Cuspidor Unit Control Panel

ONOFF

W A

LP

21

0

6 11432

-11-

(3)CuspidorUnitBodyA.Assistant’sSyringeFlowControlKnobs(Fig.3-23) Assistant’s syringe flow control knobs are locatedinthecuspidorunitbody.Theyellowcappedknobistoadjusttheassistant's syringe air flow volume, and the blue capped knob is to adjust water flow volume.

B. Cupfiller Flow Control Knob (Fig.3-23) Cupfiller flow volume can be controlled by the cupfiller flow control knob. (Pinch valve system) Loosen the lock nut and adjust cupfiller water flow volume by turning the knob.Tightenthelocknutafteradjustment.

C.BowlFlushFlowControlKnob(Fig.3-23) Bowl flush flow volume can be controlled by the bowl flush flow control knob.(Pinch valve system) Loosen the lock nut and adjust bowl flush water flow volume by turning the knob.Tightenthelocknutafteradjustment.

Note : Turning a knob counterclockwise increase flow volume and turning clockwise will decrease.

Fig.3-23FlowControlKnobsinCuspidorUnitBody

(5) Sensor Cupfiller (Optional) (Fig.3-2, Fig.3-3 & Fig.3-25) Place the cup (paper cup) on the cupfiller base, water comes out from the cupfiller nozzle, fills up the cup and stops automatically. When cupfiller starts, the bowl flush also starts, andwillrunforabout6sec.anditstopsautomatically. While filling the cup, by momentarily pressing the cupfiller switch ( ) this will cancel the cup filler water flow. During bowl flush, momentarily press the bowl flush switch ( ) this will cancel the boul flush water flow.

Note:Useonlysuitabledisposablepapercup(dentalpapercup). Use only an empty cup, using a cup with some water left, can cause an over flow. The sensor cupfiller needs over 2 seconds interval between cup filling.

Fig.3-25 Sensor Cupfiller

Cupfiller Nozzle

Bowl Flush Nozzle

Cupfiller Base

Paper Cup

(4)AssistantInstrumentHolder(Fig.3-24)Whenpickingupaninstrument(SalivaejectororVacuumhandpiece)fromtheassistantholderthisstartstheinstrumentworkingautomatically.Returningtheinstrumenttotheholderstopsautomatically.Salivaejectorhandpieceandvacuumhandpiecehavestopvalvestocloseandadjustsuctionpower.

Fig.3-19 VacuumHandpieceandSalivaEjectorHandpiece

Vacuum Handpiece

Saliva EjectorHandpiece

Open

Close

Open

Close

Assistant's SyringeWater Flow Control Knobs

Assistant's SyringeAir Flow Control Knobs

Lock Nut

Bowl Flush FlowControl Knob

Cupfiller Flow Control Knob

Fig.3-24VacuumHandpieceandSalivaEjectorHandpiece

-12-

(1)FootControl(TypeA2)(Fig.3-29)A.DriveAirPedalPickupahandpiecefromthehandpieceholderanddepressthedriveairpedal,thehandpiecestartsrunning. B.CoolantWaterSwitchCoolantwaterswitchallowshandpiececoolantwatertobeturnedonoroff.

C.ChipBlowerPedalBydepressingthechipblowerbutton,thechipairwillcomeoutfromhandpiecewithouttheburrotating.

Fig.3-29FootControl(TypeA2)

3-3.FOOTCONTROLSECTION

(6)CuspidorBowl(Optional)(Fig.3-26) The cuspidor bowl can be rotated either 90˚ to the inside and 90˚ to the outside.

Coolant WaterSwitch

Drive Air Pedal

OFF

ON Chip Blower Button

Fig.3-26CuspidorBowlRotation

90˚�

90˚�

Inside�(Chair Side)

Assistant HolderLock / Release Button

Balance Arm

(7)HeightAdjustableAssistantArm(Optional)(Fig.3-27)Pressthelockreleasebuttonandraisearmtoadjusttheassistantholderheight.Positionatdesiredheightandreleasethelockbuttonafterthat.Note:Supportthearmwithyourhanduntilitispositionedatthedesiredheight.

Fig.3-27HeightAdjustableAssistantArm

Cupfiller nozzle

Bottom of the cuspidor bowl

CAUTION

Do not hold the cupfiller nozzle when rotating thecuspidorbowl;besuretoholdthebottomof the spittoon bowl. Rotating via the cupfiller nozzlemayresult indamage to thecupfillernozzle.

Fig.3-28DentalLight

(8)DentalLight(Fig.3-28)Pleaserefertooperatinginstructionfordentallight.

Coolant WaterSwitch

Drive Air Pedal

Chip Blower Button

Increase Electric MotorRotation Speed

(2)ElectricMotorFootControl(TypeSE)(Fig.3-30)A.DriveAirPedalPickupahandpiecefromthehandpieceholderanddepressthedriveairpedal,thehandpiecestartsrunning. B.CoolantWaterSwitchMomentarilydepressingthecoolantwaterswitchischangedhandpiececoolantwaterandairsituation.Thesituationisshownonthemaincontrolpanel.Refertopage3CoolantWaterON/OFFSwitch.

C.ChipBlowerButtonBydepressingthechipblowerbutton,thechipairwillcomeoutfromhandpiecewithouttheburrotating.

E.CoolantWaterSwitch/ElectricMotorRotationDirectionSwitch(Optional)Thecoolantwaterswitchcanbechangedforelectricmotorrotationdirectionswitch.Tochangetoelectricmotorrotationdirectionswitch.Keepdepressingthecoolantwaterswitchuntilbuzzersound(about2sec.).Toreturntooriginal(coolantwaterswitch)setting.Keepdepressingthecoolantwaterswitchuntilbuzzersound(about2sec.).TheelectricmotorrotationdirectionisindicatedonthecontrolpanelbyLED.Pleaseseepage4ElectricMotorRotationDirectionControlSwitch.

D.ElectricMotorRotationControl(Optional)Pickuptheelectricmotorfromthehandpieceholderandwhilepressingdownslidedriveairpedalhorizontallytoright,andtheelectricmotorwillstartrunning.Therotationspeedincreasesbyslidingthedriveairpedalfurthertotheright.Thespeedcontrolbythefootcontroliswithinthelimitsoftheelectricmotorspeedsetting.

Fig.3-30ElectricMotorFootControl(TypeSE)

Inthefollowingcasesthesafetylockdevicetolockthechairmovementisactivated.1.Whenthepedalofthefootcontrollerisdepressed.2.Whenanyswitchonthedoctorcontrolpanelortheassistantcontrolpanelisdpressedwhilethechairismoving.3.Duringsettingwiththefunctionswitchonthedoctorcontrolpanel.4.Whenthecupidorbowlisrotatedtowardthepatientside.Note:Pleaserefertopage3(Fig3-9).

-13-

10

4. SAFETY LOCK DEVICE

7

8

Fig.5-1CuspidorBowl,DrainCapandBasketStrainer

Fig.5-2SolidCollectorFilter

Drain Cap

BasketStrainer

Cuspidor Bowl

CupfillerBase

Solid CollectorFilter

5. CARE AND MAINTENANCE

TurnOFFthemasterswitchafterdailyoperationandforlongtermintervals.

CleaningUnit

(1)CuspidorBowl(Fig.5-1)Takeoutthedraincapandthebasketstrainerlocatedinthecentreofcuspidorbowlandcleanthem. Remove the cupfiller base and pull out the cuspidor bowl andcleanit. After cleaning, secure the cuspidor bowl firmly.

Turnoffthemainswitchbeforeremovingthecuspidorbowl.

(2)SolidCollector(Fig.5-2) Pull out the solid collector filter and clean it. After cleaning, refit the solid collector firmly.

-14-

Fig.5-3 VacuumHandpieceandSalivaEjector

(3)Handpiece1-1.VacuumHandpieceandSalivaEjector(Fig.5-3)Pullandremovethetoppartsofeachhandpieceandcleanstrainer. Washing Removedirtwithtapwaterbeforesterilization.

Sterilization VacuumTip/SalivaEjectorTip/VacuumCap/VacuumHandpieceBody/SalivaEjectorHandpieceBodycanbeautoclave.Vacuumhandpiecebodyandsalivaejectorbodyhavetoassemblebeforeautoclave.A.Insertthehandpieceinasterilizationpouchandsealit. B. Autoclave for 20 min. at 121℃ StorageAftercleaningthevacuumtipandsalivaejectortip,keepitinthecleanplace.

Note :Theslideknobcanbeautoclave100timesandisexpendablesupplies.

Skip the drying process if the temperature is to exceed 135℃.Ifdamageoccurstothesterilizationpouch,discard,andsterilizeagainusinganewpouch.

CAUTION

Vacuum Tip

Saliva EjectorHandpiece

VacuumHandpiece

Vacuum

Vacuum Cap

Saliva EjectorT ip

Saliva EjectorHose

Body Body

Hose

Slide KnobSlide Knob

AllsurfacescanbecleanedwithDURRFD333cleaner.Spraythecleaner(DURRFD333)onclothandwipethesurfaceswiththecloth.Donotdrenchthechairandunit.Wipeallsurfacesdryaftercleaning.

CAUTION

CAUTION

CAUTION

Fig.5-6AirFilterDrainValveandMainWaterValve

(4)TubingsandhosesTubingsandhosescanbecleanedwithDURFD333cleaner.

(5)AirFilterDrainValve(Fig.5-6) Air filter drain valve is located under the maintenance lid.Onceaweekopenthedrainvalveanddrainoffwaterfromtheairline.

(6)MainWaterValve(Optional)(Fig.5-6)Mainwatervalveislocatedunderthemaintenancelid.Turnoffthemainwatervalveafterdailyoperationandforlongtermintervals.(7)FilterReplacement(Fig.5-7) The water filter in the junction box needs to be replaced atleastonceayear. The air filter in the junction box needs to be replaced atleastonceeverythreeyears.Contactyourlocalservicerepresentativeforreplacement.

1-2.Vacuumhoseandsalivaejectorhosearedetachablefromthecuspidorunit.(Fig.5-4) Turn the hose connector 90˚ counterclockwise the hose canthenberemovedfromthecuspidorunit. Insert the hose connector and turn through 90˚ clockwisetoreconnect.Note:Afterdailyoperation,runtwocupofcleanwaterthroughhandpiecestocleaninside.

-15-

Nozzle

Fig.5-5Belmont77Syringe

2.MicroMotor/Turbine/ScalerSterilizethehandpieceaccordingtomanufacturer’soperatingmanual.

3.Belmont77Syringe(Fig.5-5)Removethenozzlefromsyringeandcleanit. WashingRemovedirtwithtapwaterbeforesterilization.SterilizationThenozzlecanbesterilizedwithautoclave.A.Insertthehandpieceinasterilizationpouchandsealit. B. Autoclave for 20 min. at 121℃ StorageAftercleaningthenozzle,keepitinthecleanplace.

Fig.4-4 VacuumandSalivaEjectorHose

Vacuum Hose Saliva EjectorHose

HoseConnector

Fix

FixRelease

Release

W A

Pump Cover

Maintenance LidMain WaterValve (Optional)

Air Filter Drain Valve

Open

Close

Close

Open

Fig.5-4VacuumandSalivaEjectorHose

Air FilterWater Filter

Fig.5-7Filter

Skip the drying process if the temperature is to exceed 135℃.Ifdamageoccurstothesterilizationpouch,discard,andsterilizeagainusinganewpouch.

CAUTION

6. ELECTROMAGNETIC COMPATIBILITY(EMC)MedicalelectricalequipmentneedsspecialprecautionsregardingEMCandneedstobeinstalledandputintoserviceaccordingtotheEMCinformationprovidedinthismanual.PortableandmobileRFcommunicationsequipmentcanaffectmedicalelectricalequipment.Theequipmentorsystemshouldnotbeusedadjacenttoorstackedwithotherequipment.Ifadjacentorstackeduseis necessary, the equipment or system should be observed to verify normal operation in the configuration in which it will beused.

Guidance and manufacture’s declaration – electromagnetic emissionsThe CLESTA II Unit is intended for use in the electromagnetic environment specified below. The customer or the useroftheCLESTAIIUnitshouldassurethatitisusedinsuchanenvironment.

Emissions test Compliance Electromagnetic environment - guidanceRFemissionsCISPR11 Group1

TheCLESTAIIUnitusesRFenergyonlyforitsinternalfunction.Therefore,itsRFemissionsareverylowandarenotlikelytocauseanyinterferenceinnearbyelectronicequipment.

RFemissionsCISPR11 ClassB TheCLESTAIIUnitissuitableforuseinallestablishments,

includingdomesticestablishmentsandthosedirectlyconnectedtothepubliclow-voltagepowersupplynetworkthatsuppliesbuildingsusedfordomesticpurposes.

HarmonicemissionsIEC61000-3-2 ClassA

Voltage fluctuations/FlickeremissionsIEC61000-3-3

Complies

Guidance and manufacture’s declaration – electromagnetic immunityThe CLESTA II Unit is intended for use in the electromagnetic environment specified below. The customer or the useroftheCLESTAIIUnitshouldassurethatitisusedinsuchanenvironment.

Immunity test IEC 60601test level Compliance level Electromagnetic environment-

guidanceElectrostaticdischarge(ESD)IEC61000-4-2

±6kVcontact±8kVair

±6kVcontact±8kVair

Floorsshouldbewood,concreteorceramic file. If floors are covered withsyntheticmaterial,therelativehumidityshouldbeatleast30%.

Electricalfasttransient/burstIEC61000-4-4

±2kVforpowersupplylines±1kVforinput/outputlines

±2kVforpowersupplylines±1kVforinput/outputlines

Mainspowerqualityshouldbethatofatypicalcommercialorhospitalenvironment.

SurgeIEC61000-4-5

±1kVdifferentialmode±2kVcommonmode

±1kVdifferentialmode±2kVcommonmode

Mainspowerqualityshouldbethatofatypicalcommercialorhospitalenvironment.

Voltagedips,shortinterruptionsandvoltagevariationsonpowersupplyinputlinesIEC61000-4-11

<5%UT

(>95%dipinUT)for0.5cycle40%UT

(60%dipinUT)for5cycle70%UT

(30%dipinUT)for25cycle<5%UT

(>95%dipinUT)for5s

<5%UT

(>95%dipinUT)for0.5cycle40%UT

(60%dipinUT)for5cycle70%UT

(30%dipinUT)for25cycle<5%UT

(>95%dipinUT)for5s

Mainspowerqualityshouldbethatofatypicalcommercialorhospitalenvironment.IftheuseroftheCLESTAIIUnitrequirescontinuedoperationduringpowermainsinterruptions,itisrecommendedthattheCLESTAIIUnitbepoweredfromanuninterruptiblepowersupplyorabattery.

Powerfrequency(50/60Hz)magnetic fieldIEC61000-4-8

3A/m 3A/m Power frequency magnetic fields shouldbeatlevelscharacteristicofatypicallocationinatypicalcommercialorhospitalenvironment.

NOTEUTisthea.c.mainsvoltagepriortoapplicationsofthetestlevel.

-16-

Guidance and manufacture’s declaration – electromagnetic immunityThe CLESTA II Unit is intended for use in the electromagnetic environment specified below. The customer or the useroftheCLESTAIIUnitshouldassurethatitisusedinsuchanenvironment.

Immunity test IEC 60601 test level Compliance level Electromagnetic environment -guidance

PortableandmobileRFcommunicationsequipmentshouldbeusednoclosertoanypartoftheCLESTAIIUnit,includingcables,thantherecommendedsepara-tiondistancecalculatedfromtheequationapplicationstotheFrequencyofthetransmitter.

Recommended separation distance

ConductedRFIEC61000-4-6

3Vrms150kHzto80MHzoutsideISMbandsa

3Vrms d = 1.2√P

RadiatedRFIEC61000-4-3

3V/m80MHzto2.5GHz

3V/m d = 1.2√P 80MHzto800MHzd = 2.3√P 800MHzto2.5GHz

WherePisthemaximumoutputpowerratingofthetransmitterinwatts(W)accordingtothetransmittermanufactureranddistherecommendedseparationdistanceinmetres(m).

Field strengths from fixed RF transmitters, as determinedbyanelectromagneticsitesurvey,ashouldbelessthanthecompliancelevelineachfrequencyrange.b

Interferencemayoccurinthevicinityofequipmentmarkedwiththefollowingsymbol:

NOTE1At80MHzand800MHz,thehigherfrequencyrangeapplies.NOTE2Theseguidelinesmaynotapplyinallsituations.Electromagneticpropagationisaffectedby adsorption and reflection from structures, objects and people.

a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobileradios,amateurradio,AMandFMradiobroadcastandTVbroadcastcannotbepredictedtheoreticallywith accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the CLESTA II Unit isusedexceedstheapplicableRFcompliancelevelabove,theCLESTAIIUnitshouldbeobservedtoverifynormaloperation.Ifabnormalperformanceisobserved,additionalmeasuresmaybenecessary,suchasreorientingorrelocatingtheCLESTAIIUnit.

b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3V/m.

-17-

Essential performance (purpose of IMMUNITY testing)Unless operated by the switches for chair control, the chair connected to CLESTA II does not make any movements, except for sounding a buzzer and switching on/off the indicator.

Recommended separation distances betweenPortable and mobile RF communications equipment and the CLESTA II Unit

TheCLESTAIIUnitisintendedforuseinanelectromagneticenvironmentinwhichradiatedRFdisturbancesarecontrolled.ThecustomerortheuseroftheCLESTAIIUnitcanhelppreventelectromagneticinterferencebymaintainingaminimumdistancebetweenportableandmobileRFcommunicationsequipment(transmitters)andtheCLESTAIIUnitasrecommendedbelow,accordingtothemaximumoutputpowerofthecommunicationsequipment.

Rated maximum output power of transmitter

W

Separation distance according to frequency of transmitterm

150 kHz to 80 MHzd = 1.2√P

80 MHz to 800 MHzd = 1.2√P

800 MHz to 2.5 GHzd = 2.3√P

0.01 0.12 0.12 0.230.1 0.38 0.38 0.731 1.2 1.2 2.3

10 3.8 3.8 7.3100 12 12 23

Fortransmittersratedatamaximumoutputpowernotlistedabove,therecommendedseparationdistancedinmetres(m)canbeestimatedusingtheequationapplicabletothefrequencyofthetransmitter,wherePisthemaximumoutputpowerratingofthetransmitterinwatts(W)accordingtothetransmittermanufacturer.NOTE1At80MHzand800MHz,theseparationdistanceforthehigherfrequencyrangeapplies.NOTE2Theseguidelinesmaynotapplyinallsituations.Electromagneticpropagationisaffectedbyadsorption and reflection from structures, objects and people.

-18-

7. List of Compatible Handpieces

DESCRIPTION

Syringe LUZZANI(3-way ) Minilight w/Light

LUZZANI(6-way ) Minilight w/Light

DCI (3-way)

Turbine BIEN AIR BORA S36L / UNIFIX with LIGHT

NSK Ti-Max X

Air motor BIEN AIR Aquilon 830 / UNIFIX with LIGHT /PM1132

NSK EX-203 / EX-6

Micromotor BIEN AIR MC3LK / PLMP021PCB. / PM1132

BIEN AIR MC3LK / PL970 PCB. / PM1132

BIEN AIR MX / DMX PCB. / PM1132

BIEN AIR ISOLITE(LK 40 IR E) / PLMP021PCB. / PM1132

BIEN AIR ISOLITE(LK 40 IR E) / PL970. / PM1132

NSK NL-400 / NL-400SB.PCB / EX-6

NSK TIM-40J / DA-290N PCB. / EX-6

Scaler SATELEC SP4055 w/Light

NSK VARIOS VA 150 LUX(w/light)

EMS SCALER

-19-

2-1-1, Higashishinsaibashi,Chuo-ku,Osaka, 542-0083,JapanTEL : +81 6 6213 5945 FAX : +81 6 6212 3680

TAKARA BELMONT CORPORATION

NOTE

Printed in Japan 2011-05BOOK NO. FEFA23H0

Takara Belmont (UK) Ltd.Belmont HouseOne St.Andrews Way,Bow,London E3 3PA U.K.Tel: (44)20 7515 0333Fax:(44)20 7987 3596