DENISON CALZONI Radial Piston Motor Type MR, MRE Hydraulics/02 - Radial... · Radial Piston Motor...

DENISON CALZONIRadial Piston Motor

Type MR, MRE

RCOe 1806/07.01

2RCOe 1806/07.01

TABLE OF CONTENTS - MOTOR TYPE MR - MRE

The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a lega l sense.

All rights reserved. Subject to revision.

CONTENTS PAG.

TABLE OF CONTENTS 2

GENERAL CHARACTERISTICS 3

FUNCTIONAL DESCRIPTION 4

TECHNICAL DATA 5

FLUID SELECTION 6

FLUSHING PROCEDURE 7

OPERATING DIAGRAM MOTOR TYPE MR 33 MR 57 MR 73 8



OPERATING DIAGRAM MOTOR TYPE MR 250 MR 300 MRE 330 11



OPERATING DIAGRAM MOTOR TYPE MR 1100 MRE 1400 MR 1600 14




OPERATING DIAGRAM MOTOR TYPE MR 7000 MRE 8200 18

OPERATING DIAGRAM (RUNNING PRESSURE DIFFERENCE AT NO LOAD) 19-20

OPERATING DIAGRAM (MOTOR /PUMP: BOOST PRESSURE) 20-21

RADIAL LOAD 22

BEARING LIFE 23

MOTOR DIMENSIONS 24-25

SHAFT END DIMENSIONS 26-27

COMPONENTS FOR SPEED CONTROL 28-29

PIPE CONNECTION FLANGES 30

COUPLINGS - KEY ADAPTERS 31

HOLDING BRAKE - UNIT DIMENSIONS - TECHNICAL DATA 32-33

INSTALLATION NOTES 34

ORDERING CODE 35

SALES AND SERVICE LOCATIONS WORLDWIDE 36

3RCOe 1806/07.01

GENERAL CHARACTERISTICS - MOTOR TYPE MR - MRE

CONSTRUCTION

TYPE

MOUNTING

CONNECTION

MOUNTING POSITION

BEARING LIFE, RADIAL LOAD

DIRECTION OF ROTATION

FLUID

FLUID TEMPERATURE RANGE

VISCOSITY RANGE 1)

FLUID CLEANLINESS

Fixed displacement radial piston motor

MR ; MRE

Front flange mounting

Connection flange

Any (please note the installation notes on page 34)

See page 22 and 23

Clockwise, anti-clockwise - reversible

HLP mineral oils to DIN 51 524 part 2; Fluid type HFB, HFC and Bio-fluids onenquiry. FPM seals are required with phosphorous acid-Ester (HFD)

t °C – 30° to + 80°

n mm2/s 18 to 1000: Recommended operating range 30 to 50 (see fluid selectionon page 6)

Maximum permissible degree of contamination of fluid NAS 1638 Class 9. Wetherefore recommend a filter with a minimum retention rate of ß10 > 75.To ensure a long life we recommend class 8 to NAS 1638.This can be achieved with a filter, with a minimum retention rate of ß5 >100.

A B

GENERAL CHARACTERISTICS

1) For different valves of viscosity please contact DENISON Calzoni



4RCOe 1806/07.01

FUNCTIONAL DESCRIPTION - MOTOR TYPE MR - MRE

FUNCTIONAL DESCRIPTION The outstanding performance of this motor is the result of an original and patented design.

The principle is to transmit the effort from the stator to the rotating shaft (2) by means of

a pressurized column of oil (a) instead of the more common connecting rods, pistons, pads

and pins.

This oil column is contained by a telescopic cylinder (1) with a mechanical connection

at the lips at each end which seal against the spherical surfaces of the cylinder-heads (3)

and the spherical surface of the rotating shaft (4).

These lips retain their circular cross section when stressed by the pressure so there is no

alteration in the sealing geometry. The particular selection of materials and optimisation

of design has minimized both the friction and the leakage.

Another advantage of this design stems from the elimination of any connecting rods, the

cylinder can only expand and retract linearly so there are no transverse components of

the thrust. This means no oval wear on the moving parts and no side forces on the cylinder

joints.

A consequence of this novel design is a significant reduction in weight and overall sizecompared with other motors of the same capacity.

TIMING SYSTEM The timing system is realized by means of a rotary valve (5) driven by the rotary valve

driving shaft (8) that it is connected to the rotating shaft.

The rotary valve rotates between the rotary valve plate (6) and the reaction ring (7)

which are fixed with the motor's housing. This timing system is also of a patented design

being pressure balanced and self compensating for thermal expansion.

EFFICIENCY The advantages of this type of valve coupled with a revolutionary cylinder arrangement

produce a motor with extremly high values of mechanical and volumetric efficiency.

The torque output is smooth even at very low speed and the motor gives a high perfor-

mance starting under load.

A B

2 1a 3

8 6 5 74



5RCOe 1806/07.01

TECHINICAL DATA - MOTOR TYPE MR - MRE

eziS eziS eziS eziS eziSrotoMnoisrev

-ecalpsiD -ecalpsiD -ecalpsiD -ecalpsiD -ecalpsiDtnem

tnemoM tnemoM tnemoM tnemoM tnemoMfoaitreni

gnitatorstrap

-eroehT -eroehT -eroehT -eroehT -eroehTlacit

cificepseuqrot

.niM .niM .niM .niM .niM.tratseuqrot

/-eroehT

laciteuqrot

erusserPmumixaM erusserPmumixaM erusserPmumixaM erusserPmumixaM erusserPmumixaM egnardeepS egnardeepS egnardeepS egnardeepS egnardeepS mumixaM mumixaM mumixaM mumixaM mumixaMtuptuorewop

thgieW thgieW thgieW thgieW thgieW

tupni gnihsulf gnihsulf

.tnoc .tni kaep B+A niarD tuohtiw htiw tuohtiw htiw

V J % p p p p p n n P P m

mc 3 mcgk 2 rab/mN rab rab rab rab rab mpr mpr Wk Wk gk

MMMMMR

3333333333 1,23 23,4 05,0 09

052 003 024 004

5rab51(

htiw"1F"tfahs)laes

0041-1 0041-1 6,6 01 03

7575757575 4,65 67,4 09,0 09 0031-1 0031-1 11 71 03

3737373737 6,27 30,41 02,1 09 0021-1 0021-1 51 02 83

3939393939 6,29 11,51 05,1 09 0511-1 0511-1 71 52 83

011 011 011 011 011 0,901 91,61 07,1 09 0011-1 0011-1 81 82 83

521 521 521 521 521 7,421 88,65 00,2 09 009-1 009-1 71 52 64

061 061 061 061 061 7,951 05,75 45,2 09 009-1 009-1 02 03 64

091 091 091 091 091 6,191 02,85 50,3 09 058-1 058-1 42 63 64

002 002 002 002 002 2,991 51,75 02,3 09 008-1 008-1 52 83 05

052 052 052 052 052 9,052 08,06 00,4 09 008-1 008-1 23 84 05

003 003 003 003 003 1,403 34,56 08,4 09 057-1 057-1 53 35 05

053 053 053 053 053 5,943 09,522 75,5 09 046-1 046-1 14 26 77

054 054 054 054 054 6,154 08,922 02,7 09 006-1 006-1 64 57 77

006 006 006 006 006 9,706 70,562 07,9 09 025-1 025-1 65 48 79

007 007 007 007 007 9,607 04,853 03,11 09 005-1 005-1 56 79 79

0011 0011 0011 0011 0011 8,5211 05,154 09,71 09 033-5,0 033-5,0 77 911 041

0061 0061 0061 0061 0061 4,8951 34,666 04,52 09 062-5,0 062-5,0 69 441 902

0081 0081 0081 0081 0081 6,9081 01,458 08,82 09 052-5,0 052-5,0 301 351 902

0042 0042 0042 0042 0042 0,3932 04,5382 01,83 09 022-5,0 022-5,0 021 381 523

0082 0082 0082 0082 0082 0,2972 07,5792 05,44 09 512-5,0 512-5,0 721 491 523

0063 0063 0063 0063 0063 8,6363 04,1584 09,75 09 051-5,0 081-5,0 321 581 805

0054 0054 0054 0054 0054 7,2054 01,5105 09,75 19 031-5,0 071-5,0 041 012 805

0056 0056 0056 0056 0056 5,0646 6,67311 75,301 19 011-5,0 031-5,0 561 042 008

0007 0007 0007 0007 0007 2,7696 6,67311 93,111 19 001-5,0 031-5,0 071 052 008

MMMMMRE

033 033 033 033 033 4,233 05,56 03,5 09

012 052 053 004

5rab51(

htiw"1F"tfahs)laes

057-1 057-1 23 94 05

005 005 005 005 005 9,794 08,922 39,7 09 006-1 006-1 64 07 77

008 008 008 008 008 2,408 04,853 18,21 09 054-1 054-1 56 39 79

0041 0041 0041 0041 0041 5,9631 05,154 08,12 29 082-5,0 082-5,0 77 201 541

0012 0012 0012 0012 0012 2,1902 01,458 03,33 19 052-5,0 052-5,0 001 841 122

0013 0013 0013 0013 0013 7,3013 07,5792 04,94 19 512-5,0 512-5,0 521 091 923

0045 0045 0045 0045 0045 2,1045 01,5105 10,68 29 021-5,0 061-5,0 041 012 215

0028 0028 0028 0028 0028 4,6228 6,67311 09,031 29 09-5,0 021-5,0 071 052 018

EHTNIELBALIAVAERASTNEMECALPSIDREGRAL EHTNIELBALIAVAERASTNEMECALPSIDREGRAL EHTNIELBALIAVAERASTNEMECALPSIDREGRAL EHTNIELBALIAVAERASTNEMECALPSIDREGRAL EHTNIELBALIAVAERASTNEMECALPSIDREGRAL FTRM-ETRM-TRM FTRM-ETRM-TRM FTRM-ETRM-TRM FTRM-ETRM-TRM FTRM-ETRM-TRM SEIRESROTOM SEIRESROTOM SEIRESROTOM SEIRESROTOM SEIRESROTOM

The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.


6RCOe 1806/07.01

FLUID SELECTION - MOTOR TYPE MR - MRE

EXAMPLE: At a certain ambienttemperature, the operating temperature in thecircuit is 50°C. In the optimum operatingviscosity range (v

rec; shaded section), this

corresponds to viscosity grades VG 46 or VG68; VG 68 should be selected.

IMPORTANT: The drain oil temperatureis influenced by pressure and speed and isusually higher than the circuit temperature orthe tank temperature. At no point in thesystem, however, may the temperature behigher than 80°C.

If the optimum conditions cannot be met dueto the extreme operating parameters or highambient temperature, we always recommendflushing the motor case in order to operatewithin the viscosity limits.

Should it be absolutely necessary to use aviscosity beyond the recommended range,you should first contact DENISON Calzonifor confirmation.

GENERAL NOTES More detailed information regarding the choice of the fluid can be requested to DENISON Calzoni.Further notes on installation and commissioning can be found on page 34 of this data sheet. Whenoperating with HF pressure fluids or bio-degradable pressure fluids possible limitations of thetechnical data must be taken into consideration, please see information sheet TCS 85, or consultDENISON Calzoni.

OPERATING VISCOSITY RANGE The viscosity, quality and cleanliness of operating fluids are decisive factors in determining thereliability, performance and life-time of an hydraulic component. The maximum life-time andperformance are achieved within the recommended viscosity range. For applications that go beyondthis range, we recommend to contact DENISON Calzoni.

nrec.

= recommended operating viscosity 30...50 mm2/s

This viscosity refers to the temperature of the fluid entering the motor, and at the same timeto the temperature inside the motor housing (case temperature). We recommend to select theviscosity of the fluid based on the maximum operating temperature, to remain within therecommended viscosity range. To reach the value of maximum continuous power theoperating viscosity should be within the recommended viscosity range of 30 - 50 cSt.

LIMITS OF VISCOSITY RANGE For limit conditions the following is valid:

nmin.abs.

= 10 mm2/s in emergency, short term

nmin.

= 18 mm2/s for continuous operation at reduced performances

nmax.

= 1000 mm2/s short term upon cold start

CHOOSING THE TYPE OF FLUID The operating temperature of the motor is defined as the greater temperature between that of theACCORDING TO THE OPERATING incoming fluid and that of the fluid inside the motor housing (case temperature).WeTEMPERATURE recommend that you choose the viscosity of the fluid based on the maximum operating

temperature, to remain within the recommended viscosity range (see diagram). Werecommend that the higher viscosity grade must be selected in each case.

FILTRATION The motor life also depends on the fluid filtration. At least it must correspond to one of thefollowing cleanliness. class 9 according to NAS 1638

class 6 according to SAE, ASTM, AIA

class 18/15 according to ISO/DIS 4406

In order to assure a longer life a cleanliness class 8 to NAS 1638 is recommended, achievedwith a filter of b

5=100. In case the above mentioned classes can not be achieved, please consult us.

CASE DRAIN PRESSURE The lower the speed and the case drain pressure, the longer the life of the shaft seal. Themaximum permissible housing pressure is

pmax = 5 barIf the case drain pressure is higher than 5 bar it is possible to use a special 15 bar shaft seal(see page 35, Seals, Code"F1").

"FPM" SEALS In case of operating conditions with high oil temperature or high ambient temperature, werecommend to use "FPM" seals (see page 35, Seals, Code "V1"). These "FPM" seals should beused with HFD fluids.



Temperature t in °C

Oil temperature range

visc

osity

n (

mm

2 /s)

n R

EC

7RCOe 1806/07.01

FLUSHING PROCEDURE - MOTOR TYPE MR - MRE

FLUSHING CIRCUIT(MONO-DIRECTIONAL ROTATION)

FLUSHING CIRCUIT(BI-DIRECTIONAL ROTATION)

FLUSHING The motor case must be flushed when the continuous operating performances of themotor are inside the "Continuous operating area with flushing" (see Operating Diagramfrom page 8 to page 18), in order to assure the minimum oil viscosity inside the motor caseof 30 mm2/s (see page 6 - Fluid Selection). The flushing can be necessary also when theoperating performances are outside the "Continuous operating area with flushing", but thesystem is not able to assure the minimum viscosity conditions requested by the motor asspecified at page 6.

NOTE1: The oil temperature inside the motor case is obtainable by adding 3°C to the motor surfacetemperature (t

A , see figures).

NOTE2: With the standard shaft seal the maximum drain case pressure is 5 bar. For the selectionof the restrictor, please consult us.

FLOW

EPYT NOISREVROTOMGNIHSULF

WOLF

RM 011,39,37,75,33 nim/l5=Q

ERM-RM 033,003,052,002,091,061,521 nim/l6=Q

ERM-RM 005,054,053 nim/l8=Q

ERM-RM 0041,0011,008,007,006 nim/l01=Q

ERM-RM 0012,0081,0061 nim/l51=Q

ERM-RM,0045,0054,0063,0013,0082,0042

0028,0007,0056nim/l02=Q



1) Please consult us.

according to the oil temperatureand viscosity

1)“VFC” Flushing valve.

RestrictorRestrictor

8RCOe 1806/07.01

OPERATING DIAGRAM - MOTOR TYPE MR - MRE

11111 Output power 2 Intermittent operating area 3 Continuous operating area with flushing

4 Continuous operating area 5 Inlet pressure hhhhhttttt Total efficiency hhhhhvvvvv Volumeter efficiency

OPERATING DIAGRAM (average values) measured at n = 36 mm2/s; t = 45° C; p outlet = 0 bar



Torq

ue in

Nm

Speed in rpm

MR 73

81% 79

%

ht=83%

77% 75%

v=98%

h

97%

96%

46 l/min9 l/min3 l/min 18 l/min 27 l/min 37 l/min 55 l/min 64 l/min 82 l/min73 l/min

600200 400

240

160

80

800 1000 1150

400

320

100 bar

150 bar

200 bar

250 bar

20 Kw

17 Kw18 Kw

15 Kw

13 Kw

8 Kw

10 Kw

6 Kw

300 bar

5

4

3

2

1

60

30

90

120

150

180

210

200 400 600 800 1000 1200 1300

Torq

ue in

Nm

Speed in rpm

MR 57

73%

h

t=83%h

81% 79%

76%

70%

v=98%

97%

96%

8 l/min 16 l/min 39 l/min32 l/min24 l/min 47 l/min 55 l/min 71 l/min63 l/min

100 bar

150 bar

200 bar

300 bar

250 bar3 K

w

7 Kw

5 Kw

15 Kw

11 Kw

9 Kw

13 Kw

17 Kw

5

4

3

2

1

Torq

ue in

Nm

Speed in rpm

MR 33

v=98%

27 l/min13 l/min1 l/min 4 l/min 9 l/min 18 l/min 22 l/min 40 l/min31 l/min 36 l/min 45 l/min

10Kw

t=83%97%

80%

100 bar

150 bar

94%

96%

250 bar

200 bar

300 bar

5Kw

3Kw

4Kw

8Kw

7Kw

9Kw

6.6Kw

77%

75%

30

15

140 280 420 560 700 980840 1120 14001260

90

105

75

60

45

120

h

5h

3

4

2

1

9RCOe 1806/07.01







h

h

MR 125

Torq

ue in

Nm

Speed in rpm

4 Kw

7 Kw

9 Kw

11 Kw

14 Kw

20 Kw

17 Kw

23 Kw

25 Kw

t=89%88% 87% 81%85% 83

%

97%

v=98%

95%

96%

93%

68 l/min12 l/min 30 l/min 50 l/min 105 l/min85 l/min

100

100 200 400300 500

200

300

400

500

600

800600 700 900

250 bar

100 bar

150 bar

200 bar

300 bar

5

2

3

4

1

Torq

ue in

Nm

Speed in rpm

MR 110

t=83%h

77%h79%

t=81%

75%

v=98%h

97%

96%

52 l/min4 l/min

100

200

26 l/min

200

13 l/min

400

39 l/min

300

400

500

600

65 l/min

800

78 l/min 92 l/min

1050

105 l/min

21 Kw

15 Kw

8 Kw

11 Kw

19 Kw

200 bar

100 bar

150 bar

24 Kw26 Kw28 Kw

300 bar

250 bar

4

5

3

1

2

Torq

ue in

Nm

Speed in rpm

MR 93

t=83%h

81%

75%77%

79%

v=98%

h

96%

97%

22 l/min4 l/min 11 l/min 33 l/min 44 l/min 67 l/min56 l/min 78 l/min 100 l/min89 l/min

200

200

100

300

400

450

400 600 800 11001000

25 Kw100 bar

150 bar

200 bar

250 bar

300 bar

9 Kw

6 Kw

17 Kw

12 Kw

15 Kw

20 Kw

19 Kw

22 Kw5

4

3

2

1

10RCOe 1806/07.01







h

Torq

ue in

Nm

Speed in rpm

MR 200

20 Kw

5 Kw

10 Kw

15 Kw

32 Kw

25 Kw28 Kw

38 Kw

73%

t=91.5%

h

87%

91%

90%

85%

89%

77%83%

v=99%

98.5%

97.5%

150 l/min45 l/min30 l/min15 l/min 105 l/min90 l/min60 l/min 75 l/min 135 l/min120 l/min 165 l/min

300

100

200

400

500

100 200

600

800

700

900

1000

500300 400 600 700 800

150 bar

100 bar

300 bar

250 bar

200 bar

5

4

3

2

1

MR 190

Torq

ue in

Nm

36 Kw

32 Kw

28 Kw

24 Kw

20 Kw

15 Kw

10 Kw

5 Kw

5

4

3

2

1

5 l/min 15 l/min 30 l/min 45 l/min 60 l/min 75 l/min 90 l/min 120 l/min105 l/min 135 l/min 150 l/min

300 bar

250 bar

200 bar

150 bar

100 bar

50 bar

Speed in rpm100 200 300 400 500 600 700 800

900

800

700

600

500

400

300

200

100

850

MR 160

4 Kw

9 Kw

13 Kw

17 Kw

20 Kw

23 Kw

27 Kw30 Kw

Torq

ue in

Nm

300 bar

250 bar

200 bar

150 bar

50 bar

100 bar

5 l/min 15 l/min 30 l/min 45 l/min 60 l/min 75 l/min 90 l/min 120 l/min105 l/min

Speed in rpm100 200 300 400 500 600 700 800

800

700

600

500

400

300

200

100

900

5

4

3

2

1

11RCOe 1806/07.01







MR 300

5 Kw

10 Kw

15 Kw

20 Kw

25 Kw

30 Kw

35 Kw

41 Kw

47 Kw

53 Kw

40 l/min 60 l/min 80 l/min20 l/min 100 l/min 120 l/min 140 l/min 160 l/min 180 l/min 200 l/min 220 l/min

5

4

3

2

1

Torq

ue in

Nm

Speed in rpm

300 bar

250 bar

200 bar

150 bar

100 bar

50 bar

100 200 300 400 500 600 700 750

1400

1200

1000

800

600

400

200

43 Kw

9 Kw

5 Kw

48 Kw

14 Kw

32 Kw

27 Kw

23 Kw

18 Kw

37 Kw5 l/min 20 l/min 40 l/min 60 l/min 80 l/min 100 l/min

300 bar

250 bar

200 bar

150 bar

100 bar

50 bar

Torq

ue in

Nm

MR 2501200

1000

800

600

400

200

Speed in rpm

120 l/min 180 l/min160 l/min140 l/min

100 200 300 400 500 600 700

5

4

3

2

1

800

Torq

ue in

Nm

Speed in rpm

MRE 330 12 Kw

18 Kw

24 Kw

31 Kw

49 Kw

36 Kw

42 Kw

78%

t=92%

92%

h

89%

91%

86%

v=99%

h

97.5%

98.5%

30 l/min 60 l/min 100 l/min 130 l/min 220 l/min190 l/min160 l/min

200

100 200 300 400 500 600 700

1200

400

600

800

1000

1400

50 bar

150 bar

100 bar

210 bar

250 bar

3

5

4

2

1

12RCOe 1806/07.01







1

2

3

4

5

MRE 500

Torq

ue in

Nm

250 bar

180 l/min 210 l/min 240 l/min 270 l/min60 l/min 150 l/min120 l/min

7 Kw

13 Kw

20 Kw

26 Kw

33 Kw

39 Kw

46 Kw

54 Kw

62 Kw

70 Kw

210 bar

150 bar

100 bar

50 bar

30 l/min10 l/min 90 l/min

100 200 300 400 500 600

2000

1800

1600

1400

1200

1000

800

600

400

200

Speed in rpm

13 Kw

20 Kw

26 Kw

33 Kw

39 Kw

46 Kw

56 Kw

65 Kw

75 Kw

60 l/min 90 l/min10 l/min 30 l/min 150 l/min 240 l/min210 l/min180 l/min120 l/min

5

4

3

2

1

Torq

ue in

Nm

Speed in rpm

300 bar

250 bar

200 bar

150 bar

100 bar

50 bar

2200

2000

1800

1600

1400

1200

1000

800

600

400

200

100 200 300 400 500 600

MR 450

5 Kw

10 Kw

15 Kw

21 Kw

26 Kw

31 Kw

36 Kw

42 Kw

48 Kw

54 Kw

10 l/min 25 l/min 50 l/min 75 l/min 100 l/min 125 l/min 150 l/min 175 l/min 200 l/min

5

4

3

2

1

Torq

ue in

Nm

Speed in rpm

300 bar

250 bar

200 bar

150 bar

100 bar

50 bar

MR 350

100 200 300 400 500 600

200

400

600

800

1000

1200

1400

1600

1800

640

13RCOe 1806/07.01







1

2

3

4

5

MRE 800

Torq

ue in

Nm

11 Kw

43 Kw

54 Kw

65 Kw

74 Kw

84 Kw93 Kw

60 l/min20 l/min 100 l/min 200 l/min140 l/min 180 l/min 340 l/min300 l/min260 l/min

50 100 150 200 250 300 350 400 450

300

600

900

1200

1500

1800

2100

2400

2700

3000

3300

250 bar

210 bar

150 bar

100 bar

50 bar

Speed in rpm

22 Kw

33 KwMR 700

9 Kw

18 Kw

28 Kw

37 Kw

46 Kw

56 Kw

65 Kw

76 Kw

86 Kw

97 Kw

Torq

ue in

Nm

Speed in rpm

300 bar

250 bar

150 bar

100 bar

50 bar

200 bar

50 100 150 200 250 300 350 400 450 500

3000

2700

2400

2100

1800

1500

1200

900

600

300

3300

5

4

3

2

1

240 l/min120 l/min 160 l/min 200 l/min 280 l/min 320 l/min15 l/min 40 l/min 80 l/min

MR 600

16 Kw

24 Kw

32 Kw

40 Kw

48 Kw

56 Kw

65 Kw

75 Kw

84 Kw

50 100 150 200 250 300 350 400 450

5

4

3

2

1

Torq

ue in

Nm

Speed in rpm

300 bar

250 bar

150 bar

100 bar

50 bar

200 bar

3000

2700

2400

2100

1800

1500

1200

600

300

900

160 l/min100 l/min 130 l/min 190 l/min 220 l/min 250 l/min 280 l/min10 l/min 40 l/min 70 l/min

520

14RCOe 1806/07.01







Torq

ue in

Nm

Speed in rpm

MR 1600 59 Kw

44 Kw

29 Kw

98 Kw

88 Kw

108 Kw

74 Kw

144 Kw

126 Kw

91%92

%

86%

78%

90%

88%89%

84%

t=93%

92.5%

h

v=99%h

98.5%

97.5%

7525 50 100 125

1000

2000

3000

4000

175150 200 225 250

7000

5000

6000

8000

240 l/min30 l/min 120 l/min60 l/min 180 l/min

100 bar

300 l/min 360 l/min

200 bar

150 bar

5

4

300 bar

250 bar 3

2

1

40 80 120 160 200 240 280

500

1000

1500

2000

2500

3000

3500

4000

4500

5000

5500 1

2

3

4

5

MRE 1400

Torq

ue in

Nm

Speed in rpm

22Kw

33 Kw

44 Kw

55 Kw

66 Kw

77 Kw85 Kw

94 Kw102 Kw

50 l/min15 l/min 100 l/min 200 l/min 300 l/min150 l/min 250 l/min 350 l/min

210 bar

150 bar

100 bar

250 bar

50 bar

5

4

3

2

1

22 Kw

33 Kw

44 Kw

55 Kw

66 Kw

77 Kw

91 Kw

105 Kw

119 Kw

300 bar

150 bar

100 bar

50 bar

Torq

ue in

Nm

Speed in rpm

500

1000

1500

2000

2500

3000

3500

4000

4500

5000

5500

50 100 150 200 250 300 330

MR 1100

200 bar

250 bar

300 l/min100 l/min 150 l/min 200 l/min 250 l/min 350 l/min50 l/min15 l/min

15RCOe 1806/07.01







MR 2400

20 Kw

40 Kw

60 Kw

80 Kw

100 Kw

120 Kw

141 Kw

162 Kw

183 Kw

25 l/min 75 l/min

20 40 60 80 100 120 140 160 180 200 220

11000

10000

9000

8000

7000

6000

5000

4000

3000

2000

1000

5

4

3

2

1

Torq

ue i

n N

m

Speed in rpm

300 bar

250 bar

200 bar

150 bar

100 bar

50 bar

420 l/min140 l/min 210 l/min 280 l/min 350 l/min 490 l/min

MR 1800 29 Kw

44 Kw

59 Kw

74 Kw

88 Kw

103 Kw

121 Kw

139 Kw

157 Kw

240 l/min 300 l/min 420 l/min360 l/min

25 50 75 100 125 150 175 200 225 250

1000

9000

8000

7000

6000

5000

4000

3000

2000

Torq

ue in

Nm

5

4

3

2

1

Speed in rpm

300 bar

250 bar

200 bar

150 bar

100 bar

50 bar

20 l/min 60 l/min 120 l/min 180 l/min

1

2

3

4

5

MRE 2100

Torq

ue in

Nm

Speed in rpm

132 Kw

148 Kw

20 Kw

40 Kw

80 Kw

60 Kw

100 Kw

116 Kw

20 l/min 60 l/min 120 l/min 240 l/min180 l/min 300 l/min 480 l/min420 l/min360 l/min

100 bar

250 bar

50 bar

150 bar

210 bar

25 50 75 100 125 150 175 200 225 250

1000

2000

3000

4000

5000

6000

7000

8000

16RCOe 1806/07.01




1

2

3

4

5

MR 3600

26 Kw

52 Kw

78 Kw

104 Kw

130 Kw

153 Kw

175 Kw

300 l/min 400 l/min 500 l/min 600 l/min

15 30 45 60 75 90 105 120 135 150 165 180

Torq

ue in

Nm

Speed in rpm

250 bar

200 bar

150 bar

100 bar

50 bar

35 l/min 200 l/min100 l/min

300 bar

185 Kw

2000

4000

6000

8000

10000

12000

14000

16000

18000

20 40 60 80 100 120 140 160 180 200 215

Torq

ue in

Nm

MRE 3100

Speed in rpm

240 l/min

1

2

3

4

5

20 Kw

40 Kw

60 Kw

80 Kw

100 Kw

125 Kw

145 Kw

165 Kw

190 Kw

100 bar

250 bar

50 bar

150 bar

210 bar

400 l/min160 l/min 320 l/min 550 l/min480 l/min25 l/min 80 l/min1000

2000

3000

4000

5000

6000

7000

8000

9000

10000

11000

12000

13000

1000

2000

3000

4000

5000

6000

7000

8000

9000

10000

11000

12000

13000

20 40 60 80 100 120 140 160 180 200 215

MR 2800

20 Kw

40 Kw

60 Kw

80 Kw

100 Kw

127 Kw

149 Kw

172 Kw

194 Kw

Torq

ue in

Nm

Speed in rpm

300 bar

250 bar

200 bar

150 bar

100 bar

50 bar

5

4

3

2

1

25 l/min 80 l/min 160 l/min 240 l/min 320 l/min 400 l/min 480 l/min 530 l/min




17RCOe 1806/07.01




3000

6000

9000

12000

15000

18000

21000

24000

27000

30000

33000

10 20 30 40 50 60 70 80 90 100 110 120 130

1

2

3

4

5

47 Kw

71 Kw

94 Kw

118 Kw

141 Kw

165 Kw

193 Kw

222 Kw

Torq

ue in

Nm

Speed in rpm

300 bar

250 bar

200 bar

150 bar

100 bar

50 bar

100 l/min35 l/min

MR 6500

300 l/min200 l/min 400 l/min 500 l/min 600 l/min 780 l/min700 l/min

240 Kw

1

2

3

4

5

MRE 5400

Torq

ue in

Nm

Speed in rpm

35 l/min 100 l/min 200 l/min 400 l/min300 l/min 800 l/min700 l/min600 l/min500 l/min

40 Kw

60 Kw

80 Kw

140 Kw

163 Kw

187 Kw

100 Kw

210 Kw

100 bar

250 bar

50 bar

150 bar

210 bar

20 40 60 80 100 120 140 160

2000

4000

6000

8000

10000

12000

14000

16000

18000

20000

22000

120 Kw

2000

4000

6000

8000

10000

12000

14000

16000

18000

20000

22000

10 30 50 70 90 110 130 150 170

1

2

3

4

5

40 Kw

60 Kw

80 Kw

140 Kw

163 Kw

187 Kw

210 Kw

100 Kw

120 Kw

Torq

ue in

Nm

Speed in rpm

300 bar

250 bar

200 bar

150 bar

100 bar

50 bar

MR 4500

300 l/min200 l/min 400 l/min 500 l/min 600 l/min 700 l/min35 l/min 100 l/min




18RCOe 1806/07.01







3000

6000

9000

12000

15000

18000

21000

24000

27000

30000

330001

2

3

4

5

MRE 8200

Torq

ue in

Nm

Speed in rpm

49 Kw

73 Kw

97 Kw

121 Kw

146 Kw

170 Kw

200 Kw

230 Kw

250 Kw

100 bar

250 bar

50 bar

150 bar

210 bar

35 l/min 100 l/min 200 l/min 400 l/min300 l/min 800 l/min700 l/min600 l/min500 l/min 900 l/min

10 20 30 40 60 70 80 90 100 110 12050

1

2

3

4

5

MR 7000

Torq

ue in

Nm

49 Kw

73 Kw

97 Kw

170 Kw

200 Kw

230 Kw

250 Kw

300 bar

200 bar

150 bar

100 bar

50 bar

800 l/min35 l/min 100 l/min 200 l/min 300 l/min 400 l/min 500 l/min 700 l/min600 l/min

10 20 30 40 50 60 70 80 90 100 110 120 130

33000

30000

27000

24000

21000

18000

15000

12000

9000

6000

3000

Speed in rpm121 Kw

146 Kw

250 bar

19RCOe 1806/07.01



Min. required pressure difference DDDDDp with idling speed (shaft unloaded)



MR33 - 110

MR - MRE350 - 800

MR - MRE125 - 330

MR - MRE1100 - 2100

4

16

12

8

28

24

20

32

200 400 800600 1000 1200 1400

pre

ssure

dro

p in

bar

Speed in rpm

MR 110

MR 93

MR 73

MR 57

MR 33

8

4

20

16

12

32

28

24

36

50 150100 200 600300250 400350 500450 550 640

pre

ssu

re d

rop

in b

ar

Speed in rpm

MR 350MR 450

MRE 800

MR 700

MR 600MRE 50

0

12

4

8

24

20

16

36

32

28

200100 300 500400 700600 800 900Speed in rpm

pre

ssure

dro

p in

bar

MR125MR 200MR 250

MR 190

MR160

MRE 3

30

MR 300

4

8

28

24

20

16

12

pre

ssu

re d

rop

in b

ar

Speed in rpm30012030 60 90 150 180 210 240 270 330

MR 1

800MRE 2

100

MR 1100

MRE 1

400

MR 160

0

20RCOe 1806/07.01

Minimum boost pressure during pump operation



Min. required pressure difference DDDDDp with idling speed (shaft unloaded)

MR - MRE2400 - 8200

MR33 - 110

MR - MRE125 - 330



4

16

12

8

28

24

20

36

32

200 400 800600 1000 1200 1400Speed in rpm

Min

. boo

st p

ress

ure

in b

ar

MR 110

MR 73

MR 57

MR 33

MR 93

8

4

24

20

16

12

36

32

28

200100 300 500400 600 800700 950900Speed in rpm

Min

. boo

st p

ress

ure

in b

ar

MR 190

MR 200

MR 160

MR 125

MR 250

MRE 3

30

MR 300

8

4

36

32

28

24

20

16

12

604020 20012010080 180160140 220

pre

ssu

re d

rop

in b

ar

Speed in rpm

MRE 3100MR 7

000

MR 6500

MRE

820

0

MR 4500

MR 3600

MR 5400

MR 2400MR 2800

21RCOe 1806/07.01



Minimum boost pressure during pump operation

MR - MRE350 - 800

MR - MRE1100 - 2100

MR - MRE2400 - 8200



16

4

12

8

20

24

28

32

36

640100 200 300 400 500 600150 250 350 450 55050Speed in rpm

Min

. boo

st p

ress

ure

in b

ar MR 700

MRE 500

MR 600

MR 350MR 450

MRE 800

4

16

12

8

24

20

32

28

30 2409060 120 180150 210 330270 300Speed in rpm

Min

. boo

st p

ress

ure

in b

ar

MRE 2

100

MR 1

800

MRE

140

0

MR 1100

MR 1

600

8

4

24

16

12

20

36

32

28

40

10020 6040 80 120 140 160 200180 220Speed in rpm

Min

. boo

st p

ress

ure

in b

ar

MR

E 82

00

MR 3600

MR 7

000

MR 6500

MRE 5400

MR 4500

MR 2800

MR 2400MRE 3100

22RCOe 1806/07.01

RADIAL LOAD - MOTOR TYPE MR - MRE

ROTOM ROTOM ROTOM ROTOM ROTOMEPYT

LAIDAR LAIDAR LAIDAR LAIDAR LAIDARECROF XAM XAM XAM XAM XAM IIIII

YLFEIRBHTIWDETTIMREP

DAOLCIMANYDNkniF 11111)))))

ERTNECTFAHSNIECROFLAIDARDETTIMREP.XAM ERTNECTFAHSNIECROFLAIDARDETTIMREP.XAM ERTNECTFAHSNIECROFLAIDARDETTIMREP.XAM ERTNECTFAHSNIECROFLAIDARDETTIMREP.XAM ERTNECTFAHSNIECROFLAIDARDETTIMREP.XAMLNODESAB 01H 01H 01H 01H 01H SRUOH0005 SRUOH0005 SRUOH0005 SRUOH0005 SRUOH0005

nideeps nideeps nideeps nideeps nideepsmprERUSSERPTUPNI ERUSSERPTUPNI ERUSSERPTUPNI ERUSSERPTUPNI ERUSSERPTUPNI

rab002NkniF

ERUSSERPTUPNI ERUSSERPTUPNI ERUSSERPTUPNI ERUSSERPTUPNI ERUSSERPTUPNIrab051

NkniF

ERUSSERPTUPNI ERUSSERPTUPNI ERUSSERPTUPNI ERUSSERPTUPNI ERUSSERPTUPNIrab001

NkniF

33RM 33RM 33RM 33RM 33RM 0,91 5,9 2,01 6,01 004

75RM 75RM 75RM 75RM 75RM 0,91 5,9 2,01 6,01 004

37RM 37RM 37RM 37RM 37RM 5,22 0,9 6,11 5,31 053

39RM 39RM 39RM 39RM 39RM 5,22 0,9 6,11 5,31 053

011RM 011RM 011RM 011RM 011RM 5,22 0,9 6,11 5,31 053

521RM 521RM 521RM 521RM 521RM 5,22 0,5 9,9 9,21 572

061RM 061RM 061RM 061RM 061RM 5,22 0,5 9,9 9,21 572

091RM 091RM 091RM 091RM 091RM 5,22 0,5 9,9 9,21 572

*002RM *002RM *002RM *002RM *002RM - - - - -

052RM 052RM 052RM 052RM 052RM 0,82 6,5 9,9 6,21 052

003RM 003RM 003RM 003RM 003RM 0,82 6,5 9,9 6,21 052

053RM 053RM 053RM 053RM 053RM 0,53 5,41 4,81 2,12 522

054RM 054RM 054RM 054RM 054RM 0,53 5,41 4,81 2,12 522

006RM 006RM 006RM 006RM 006RM 0,34 0,51 5,22 3,72 002

007RM 007RM 007RM 007RM 007RM 0,34 0,51 5,22 3,72 002

0011RM 0011RM 0011RM 0011RM 0011RM 0,45 5,81 5,82 2,53 051

0061RM 0061RM 0061RM 0061RM 0061RM 0,86 2,62 6,04 0,05 521

0081RM 0081RM 0081RM 0081RM 0081RM 0,86 2,62 6,04 0,05 521

0042RM 0042RM 0042RM 0042RM 0042RM 0,58 1,05 0,66 8,67 011

0082RM 0082RM 0082RM 0082RM 0082RM 0,58 0,45 0,96 4,97 001

0063RM 0063RM 0063RM 0063RM 0063RM 0,801 0,55 0,09 0,301 001

0054RM 0054RM 0054RM 0054RM 0054RM 0,801 0,87 0,79 0,901 58

0056RM 0056RM 0056RM 0056RM 0056RM 0,431 0,47 0,321 0,141 05

0007RM 0007RM 0007RM 0007RM 0007RM 0,431 0,47 0,321 0,141 05

033ERM 033ERM 033ERM 033ERM 033ERM 0,82 5,4 5,8 9,11 052








11111 "1F"edocylno*002RM-detpeccaebnacseulavrehgih,noitidnoccimanydehthtiwecnadroccani) "1F"edocylno*002RM-detpeccaebnacseulavrehgih,noitidnoccimanydehthtiwecnadroccani) "1F"edocylno*002RM-detpeccaebnacseulavrehgih,noitidnoccimanydehthtiwecnadroccani) "1F"edocylno*002RM-detpeccaebnacseulavrehgih,noitidnoccimanydehthtiwecnadroccani) "1F"edocylno*002RM-detpeccaebnacseulavrehgih,noitidnoccimanydehthtiwecnadroccani)

RADIAL LOAD



23RCOe 1806/07.01

BEARING LIFE - MOTOR TYPE MR - MRE

L10h is the theoretically service life value normally reached or exceeded by the 90% of the bearings.

50 % of the bearings reach the value L50h = 5 times L 10h.

C p = Load coefficentK = Sevice life coefficent for standard bearingp = operating pressure in bar

EPYTROTOM EPYTROTOM EPYTROTOM EPYTROTOM EPYTROTOM KKKKK EPYTROTOM EPYTROTOM EPYTROTOM EPYTROTOM EPYTROTOM KKKKK EPYTROTOM EPYTROTOM EPYTROTOM EPYTROTOM EPYTROTOM KKKKK

33RM 33RM 33RM 33RM 33RM 0512 033ERM 033ERM 033ERM 033ERM 033ERM 058 0012ERM 0012ERM 0012ERM 0012ERM 0012ERM 227

75RM 75RM 75RM 75RM 75RM 0512 053RM 053RM 053RM 053RM 053RM 6211 0042RM 0042RM 0042RM 0042RM 0042RM 429







002RM 002RM 002RM 002RM 002RM 059 0041ERM 0041ERM 0041ERM 0041ERM 0041ERM 396 0007RM 0007RM 0007RM 0007RM 0007RM 017

052RM 052RM 052RM 052RM 052RM 059 0061RM 0061RM 0061RM 0061RM 0061RM 538 0028ERM 0028ERM 0028ERM 0028ERM 0028ERM 055

003RM 003RM 003RM 003RM 003RM 059 0081RM 0081RM 0081RM 0081RM 0081RM 538

BEARING LIFE



Motor speed [rpm]

Load coefficent

L50h

L10h

24R

CO

e 1806/07.01

MO

TOR

DIM

EN

SIO

NS

- MO

TOR

TY

PE

MR

- MR

E

1 Splined shaft with flank contact (for dimension see page 26)Ordering code "N1"(for further shaft ends see page 26 - 27)

2 Case drain portBSP threads to ISO 228/1

3 On request the port flange can berotated by 72°(For MR 33, MR 57, MR 73, MR 93,MR 110, MR 125, MR 160, MR 190,MR 200, MR 250, MR 300, MRE 330,MR 350, MR 450, MRE 500, MR 600,MR 700, MRE 800can be rotated by 36°)For standard position see ange a .

4 Port 1/4“ BSP threads to ISO 228/1for pressure reading.

L9

B2 B3

D6

AB

D7/T1 D11

2

2

314

Only MR 33, MR 57( SAE Standard)

fo.riDnoitatoR

nodeweiV()dnetfahs

telnitroPedocgniredro)53egapees(

esiwkcolc

esiwkcolc-itna

A

B"N"

esiwkcolc

esiwkcolc-itna

B

A"S"

The specified data are for product description purposes only and m

ust not be interpreted as warranted characteristic in a lega

l sense.

All rights reserved. S

ubject to revision.

25R

CO

e 1806/07.01

MO

TOR

DIM

EN

SIO

NS

- MO

TOR

TY

PE

MR

- MR

E



l sense.


ubject to revision.

ROTOM ROTOM ROTOM ROTOM ROTOMEPYT

1L1L1L1L1L 2L2L2L2L2L 3L3L3L3L3L 4L4L4L4L4L 5L5L5L5L5L 6L6L6L6L6L 7L7L7L7L7L 8L8L8L8L8L 9L9L9L9L9L 01L 01L 01L 01L 01L 11L 11L 11L 11L 11L 21L 21L 21L 21L 21L 31L 31L 31L 31L 31L 1B1B1B1B1B 2B2B2B2B2B 3B3B3B3B3B 4B4B4B4B4BØØØØØ1D

ØØØØØ2D

ØØØØØ3D

ØØØØØ4D 8h8h8h8h8h *****

ØØØØØ5D

ØØØØØ6D

7D7D7D7D7D 1T1T1T1T1T 8D8D8D8D8D 9D9D9D9D9DØØØØØ

01DØØØØØ

11D ααααα βββββ

33RM 33RM 33RM 33RM 33RM75RM

2,352 691 841 701 2,75 41 91 07 4,25 2,011 5,87 07 7,91 421 56 2,62 4,96 4,532 061 081 521 - 021 01M 52 4/1G 9 79 52 °801 °63

37RM 37RM 37RM 37RM 37RM39RM011RM

792 5,822 5,091 5,131 5,86 71 02 45 43 8,911 49 27 - 021 05 001 09 052 402 4,422 541 - 921 8M 51 8/3G 11 - 02 °09 °63

521RM 521RM 521RM 521RM 521RM061RM091RM

903 242 402 541 76 41 61 45 43 5,741 301 27 5,6 021 05 001 001 2,313 522 942 061 - 921 8M 51 8/3G 11 061 02 °09 °63

002RM 002RM 002RM 002RM 002RM052RM003RM033ERM

323 242 402 541 18 51 61 45 43 5,351 911 27 5,7 021 05 001 001 823 232 652 571 09 921 8M 51 8/3G 11 261 02 °09 °63

053RM 053RM 053RM 053RM 053RM054RM005ERM

673 972 532 761 79 51 81 4,07 04 5,471 031 48 5,9 241 06 021 911 863 662 692 091 69 651 01M 81 8/3G 31 491 52 °09 °63


004 992 552 781 101 51 02 4,07 04 291 341 48 8 241 06 021 331 504 092 023 022 201 651 01M 81 8/3G 31 702 52 °09 °63

0011RM 0011RM 0011RM 0011RM 0011RM0041ERM

854 143 392 302 711 02 22 28 05 322 561 501 9 261 37 631 841 074 033 763 052 021 271 21M 12 2/1G 51 822 13 °401 °63


605 473 623 632 231 12 42 28 05 462 791 501 11 261 37 631 861 855 083 324 092 841 271 21M 12 2/1G 71 662 13 °09 °63


916 664 293 582 351 42 62 89 26 303 122 321 51 802 68 081 091 246 044 494 533 041 512 41M 82 2/1G 91 413 73 °09 °63


5,996 5,984 5,814 5,703 012 43 82 89 86 5,953 742 041 91 032 611 002 042 667 045 795004

4D* 4D* 4D* 4D* 4D* 7h7h7h7h7h

- 512 61M 23 2/1G 32 083 83 °801 °63


697 665 594 483 032 73 03 89 86 3,704 742 041 12 032 611 002 462 468 006 6,856054

4D* 4D* 4D* 4D* 4D* 7h7h7h7h7h

091 512 61M 23 2/1G 52 054 83 °801 °63

26R

CO

e 1806/07.01

SH

AF

T E

ND

DIM

EN

SIO

NS

- MO

TOR

TY

PE

MR

- MR

E

1) on enquiry

Code B 1 - BS 3550 - 1) Code D 1 - DIN 5480 - (Standard)Code N 1 (Standard)



l sense.


ubject to revision.

oisreV n NNNNN BBBBB DDDDD

EPYT EPYT EPYT EPYT EPYT 5L5L5L5L5L 12L 12L 12L 12L 12L 22L 22L 22L 22L 22L 21D 21D 21D 21D 21D 01T 01T 01T 01T 01T 31DØ 31DØ 31DØ 31DØ 31DØ 5L5L5L5L5L 12L 12L 12L 12L 12L 22L 22L 22L 22L 22L 21D 21D 21D 21D 21D 01T 01T 01T 01T 01T 31DØ 31DØ 31DØ 31DØ 31DØ 5L5L5L5L5L 12L 12L 12L 12L 12L 22L 22L 22L 22L 22L 21D 21D 21D 21D 21D 01T 01T 01T 01T 01T 31DØ 31DØ 31DØ 31DØ 31DØ

33RM75RM

75 04 82 - - 23x62x6B - - - - - - 75 04 82 - - e8-02x5,1x23W

37RM39RM011RM

5,86 5,15 5,13 21M - 43x82x6B - - - - - - 5,86 5,15 5,13 21M - e8-61x2x53W

521RM061RM091RM

76 05 5,53 21M 02 83x23x8B 76 05 5,53 21M 02 71-42/21 76 05 5,53 21M 02e8-81x2x83W

*002RM - - - - - - - - - - - - - - - - - -

052RM003RM

033ERM18 06 64 21M 52 84x24x8B 18 06 54 21M 52 12-42/21 18 06 64 21M 52 e8-22x2x84W

053RM054RM

005ERM79 47 5,65 21M 52 45x64x8B 79 47 16 21M 52 71-61/8 79 47 06 21M 52 e8-71x3x55W

006RM007RM

008ERM101 87 26 21M 52 06x25x8B 101 87 26 21M 52 71-61/8 101 87 26 21M 52 e8-81x3x06W

0011RM0041ERM

711 88 96 21M 52 27x26x8B 711 88 76 21M 52 41-21/6 711 88 27 21M 52 e8-22x3x07W

0061RM0081RM

0012ERM231 001 97 21M 52 28x27x01B 231 001 67 21M 52 02-21/6 231 001 08 21M 52 e8-52x3x08W

0042RM0082RM

0013ERM351 021 99 21M 52 29x28x01B 351 021 67 21M 52 02-21/6 351 021 001 21M 52 e8-12x4x09W

0063RM0054RM

0045ERM012 371 441 21M 52 211x201x01B 012 371 5,241 21M 52 02-21/6 012 371 441 21M 52 e8-62x4x011W

0056RM0007RM

0028ERM032 881 051 21M 52 521x211x01B 032 881 351 21M 52 62-21/6 032 881 351 21M 52 e8-82x4x021W

ehtybderiuqersnoisnemidselohehtesacnI.selohecivressaderedisnocebtsum"1D"dna"1B","1N"snoisrevtfahsehtrof)01T/21D(selohdedaerhteht:ETON.inozlaCNOSINEDtcatnoceselp,evobaerehdetsilsenoehtmorftnereffideranoitacilppa

"1F"edocylno*002RM

27R

CO

e 1806/07.01

SH

AF

T E

ND

DIM

EN

SIO

NS

- MO

TOR

TY

PE

MR

- MR

E

Code P 1Code F 1 - DIN 5480 -



l sense.


ubject to revision.

noisreV noisreV noisreV noisreV noisreVFFFFF PPPPP

epyT epyT epyT epyT epyT5L5L5L5L5L 12L 12L 12L 12L 12L 22L 22L 22L 22L 22L

31DØ 31DØ 31DØ 31DØ 31DØNID 0845

5L5L5L5L5L 12L 12L 12L 12L 12L 62L 62L 62L 62L 62L 21D 21D 21D 21D 21D 01T 01T 01T 01T 01T41DØ 41DØ 41DØ 41DØ 41DØ yeK yeK yeK yeK yeK

BxL

dettimsnarT dettimsnarT dettimsnarT dettimsnarT dettimsnarTeuqrot)mN(

ETON ETON ETON ETON ETONoteuqrotehtfoseulavrehgihroF

tlusnocesaelp,dettimsnartebNOSINED inozlaC

33RM75RM

71 5 12 H9-12x52,1x82N - - - - - - -

37RM39RM

011RM71 5 62 H9-41x2x23N - - - - - - -

521RM061RM091RM

41 5 82 H9-61x2x53N 76 05 34 21M 02 6k04 21x54 694

*002RM 72 5 63 H9-81x2x04N - - - - - - - -

052RM003RM033ERM

72 5 63 H9-81x2x04N 18 06 5,35 21M 52 6k05 41x65 798

053RM054RM

005ERM82 5 83 H9-22x2x74N 79 47 95 21M 52 6k55 61x07 3141

006RM007RM

008ERM82 5 44 H9-71x3x55N 101 87 46 21M 52 6k06 81x07 0302

0011RM0041ERM

83 8 05 H9-02x3x56N 711 88 5,67 21M 52 6k07 02x08 0962

0061RM0081RM

0012ERM74 8 75 H9-42x3x57N 231 001 58 21M 52 6k08 22x09 0204

0042RM0082RM

0013ERM84 8 26 H9-72x3x58N 351 021 59 21M 52 6k09 52x011 7026

0063RM0054RM

0045ERM05 41 86 H9-23x3x001N 012 371 611 21M 52 6k011 82x061 75701

0056RM0007RM

0028ERM05 41 67 H9-53x3x011N 032 881

831**

21M 52 8b421 23x081-2°N 07282

eranoitacilppaehtybderiuqersnoisnemidselohehtesacnI.selohecivressaderedisnocebtsum"1P"snoisrevtfahsehtrof)01T/21D(selohdedaerhteht:ETON.inozlaCNOSINEDtcatnoceselp,evobaerehdetsilsenoehtmorftnereffid

"1F"edocylno*002RMsyekowtsedulcninoisnemidsihT**

Code P 1 **

Only MR 6500, MR 7000,MRE 8200

28RCOe 1806/07.01

COMPONENTS FOR SPEED CONTROL - MOTOR TYPE MR - MRE

MECHANICALTACHOMETER DRIVE

TACHOGENERATORDRIVE

ENCODERDRIVE

INCREMENTAL ENCODER

DIMENSIONS



encoder

encoder drive flangeprotection

(see page 26)

Female connector included in the supply

a = 126° for the motor types MR 33-57

a = 54° for the motor types MR 73-93-110-125-160-190-200-250-300 MRE 330

a =45° for the other types

a

( ) * Motor MR 73-93-110-125-160-190-200-250-300 MRE 330( )** Motor MR 33-57

Code "C1" Code "T1" Code "Q1"

2x M8x45 (2x M8x50)* 2x M8x45 (2x M8x50)* 2x M8x30 (2x M8x35)*

(27)**

(62)**

(27)**(27)**

29RCOe 1806/07.01

COMPONENTS FOR SPEED CONTROL - MOTOR TYPE MR - MRE

Encoder type: ELCIS mod. 478

Supply voltage: 8 to 24 Vcc

Current consumption: 120 mA max

Current output: 10 mA max

Output signal: A phase- MONODIRECTIONALA and B phase BIDIRECTIONAL

Response frequency: 100 KHz max

Number of pulses: 500 (others on request - max 2540)

Slew speed: Always compatible with maximummotor speed

Operating temperature range: from 0 to 70 °C

Storage temperature range: from -30 to +85 °C

Ball bearing life: 1.5x109 rpm

Weigth: 100 gr

Protection degree: IP 67 (with protection andconnector assembled)

Connectors:

MONODIRECTIONAL RSF3/0.5 M (Lumberg) maleRKT3-06/5m (Lumberg) female

BIDIRECTIONAL RSF4/0.5 M (Lumberg) maleRKT4-07/5m (Lumberg) female

Note: Female connectors cable length equal to 5 m.

INCREMENTAL ENCODER

TECHNICAL DATA

Monodirectional

4 3 3 4

1 1

4 3 3 4

1 1

1 1 1

4 4

1

4 4

3 3 3 3

2 2

Femaleconnector

Maleconnector

Maleconnector

INCREMENTAL ENCODER

CONNECTION DIAGRAMS

Bidirectional

2 2

Femaleconnector

noitcnufdnaseriwroloC noitcnufdnaseriwroloC noitcnufdnaseriwroloC noitcnufdnaseriwroloC noitcnufdnaseriwroloC

11111 nworB nworB nworB nworB nworB )cdV42ot8(ylppuSrewoP

22222 etihW etihW etihW etihW etihW )ccV42-Am01XAM(esahpBtuptuO

33333 eulB eulB eulB eulB eulB )cdV0(ylppuSrewoP

44444 kcalB kcalB kcalB kcalB kcalB )ccV42-Am01XAM(esahpAtuptuO



30RCOe 1806/07.01

PIPE CONNECTION FLANGES - MOTOR TYPE MR - MRE

STANDARD CONNECTION FLANGECode “C1“

Flange is supplied complete with screws and seals.

SAE CONNECTION FLANGECodice “S1“Codice “T1“Codice “G1“Codice “L1“

Permitted up to 6000 PSI

RMRMRMRMRMERM

DDDDD)PSB(

HHHHH EDOC EDOC EDOC EDOC EDOCRBN

EDOC EDOC EDOC EDOC EDOCMPF

061-521 061-521 061-521 061-521 061-521091

052-002033-003

"4/3 63 890262 493922

054-053 054-053 054-053 054-053 054-053005

007-006008

"4/11 04 980262 593922

0041-0011 0041-0011 0041-0011 0041-0011 0041-00110081-0061

0012"2/11 54 390262 693922

0082-0042 0082-0042 0082-0042 0082-0042 0082-00420013

"2/11 06 275462 793922

0054-0063 0054-0063 0054-0063 0054-0063 0054-00630045

0007-00560028

"2 06 427272 893922

RMRMRMRMRMERM

EAS EAS EAS EAS EASISP

DDDDD

HHHHH IIIII XXXXX YYYYY

CIRTEM CIRTEM CIRTEM CIRTEM CIRTEM CNU CNU CNU CNU CNU

"""""mmmmmmmmmm

T/Z T/Z T/Z T/Z T/Z

nosineD nosineD nosineD nosineD nosineDinozlaC°Ntrap

RBN

)"(Z )"(Z )"(Z )"(Z )"(Z TTTTT

nosineD nosineD nosineD nosineD nosineDinozlaC°Ntrap

RBN

061-521 061-521 061-521 061-521 061-521091

052-002033-003

0005 "4/3 91 63 55 2,22 6,74 52/01M 592772 61-"8/3 52 533322

054-053 054-053 054-053 054-053 054-053005

007-006008

0005 "1 52 04 06 2,62 4,25 52/01M 792772 61-"8/3 52 633322

0041-0011 0041-0011 0041-0011 0041-0011 0041-00110061-0081

0012

0004 "4/11 13 54 57 2,03 7,85 52/01M 992772 41-"61/7 03 733322

0006 "1 52 54 17 8,72 51,75 22/21M 661032 41-"61/7 03 290243

0082-0042 0082-0042 0082-0042 0082-0042 0082-00420013

0003 "2/11 73 06 68 7,53 8,96 03/21M 103772 31-"2/1 03 833322

0006 "2/11 73 06 5,79 5,63 4,97 03/61M 861032 11-"8/5 53 860943

0054-0063 0054-0063 0054-0063 0054-0063 0054-00630045

0007-00560028

0003 "2 05 06 211 9,24 8,77 03/21M 303772 31-"2/1 03 933322

0006 "2 05 06 611 54,44 28,69 53/02M 071032 01-"4/3 83 745243

Flange is supplied complete with screws and seals. FPM seals enquiry.

BSP threads to ISO 228/1



31RCOe 1806/07.01

COUPLINGS - KEY ADAPTERS - MOTOR TYPE MR - MRE

COUPLINGS

1 For standard male splined shaft version "N1" (see page 26).

22222ADAPTERS WITH KEY

1 For standard male splined shaft version "N1" (see page 26).2 Key to DIN 6885

11111

11111

RMRMRMRMRMERM

GNIREDRO GNIREDRO GNIREDRO GNIREDRO GNIREDROEDOC

RRRRR3645NIDXE

)mm(ddddd IIIII DDDDD 6k6k6k6k6k LLLLL bbbbb ttttt

)mm(yeK )mm(yeK )mm(yeK )mm(yeK )mm(yeK5886NID

061-521 061-521 061-521 061-521 061-521091

711172 83x23x8A 3,83 5,51 85 05 01 16 54x8x01

003-052 003-052 003-052 003-052 003-052033

811172 84x24x8A 3,84 51 07 06 41 5,37 65x9x41

054-053 054-053 054-053 054-053 054-053005

911172 45X64x8A 3,45 5,81 08 57 61 48 07x01x61

007-006 007-006 007-006 007-006 007-006008

021172 06x25x8A 3,06 91 09 08 81 49 07x11x81

0041-0011 0041-0011 0041-0011 0041-0011 0041-0011 121172 27x26x8A 3,27 02 501 89 02 5,901 09x21x02

0081-0061 0081-0061 0081-0061 0081-0061 0081-00610012

221172 28x27x01A 3,28 22 811 811 22 321 011x41x22

0082-0042 0082-0042 0082-0042 0082-0042 0082-00420013

321172 29x28x01A 3,29 32 031 841 52 531 041x41x52

0054-0063 0054-0063 0054-0063 0054-0063 0054-00630045

917272 211x201x01A 3,211 03 061 881 82 661 081x61x82

0007-0056 0007-0056 0007-0056 0007-0056 0007-00560028

674322 521x211x01A 6,621 83 581 881 54 591 081x52x54



RMRMRMRMRMERM

GNIREDRO GNIREDRO GNIREDRO GNIREDRO GNIREDROEDOC

AAAAA BBBBB CCCCC 11H 11H 11H 11H 11H DDDDD EEEEE FFFFF GGGGG

061-521 061-521 061-521 061-521 061-521091

302564 411 65 93 74 45 5,51 5,43

003-052 003-052 003-052 003-052 003-052033

202564 531 17 94 06 46 51 54

054-053 054-053 054-053 054-053 054-053005

102564 551 08 55 86 86 5,81 5,55

007-006 007-006 007-006 007-006 007-006008

002564 171 09 16 57 08 91 95

0011 0011 0011 0011 00110041

587464 681 601 37 5,88 5,58 02 5,56

0081-0061 0081-0061 0081-0061 0081-0061 0081-00610012

991564 422 811 38 89 701 22 87

0082-0042 0082-0042 0082-0042 0082-0042 0082-00420013

891564 562 231 39 211 721 32 79

0054-0063 0054-0063 0054-0063 0054-0063 0054-00630045

296474 553 051 311 621 561 03 041

0007-0056 0007-0056 0007-0056 0007-0056 0007-00560028

445224 093 591 621 041 581 83 741

32RCOe 1806/07.01

HOLDING BRAKE UNIT DIMENSIONS - MOTOR TYPE MR - MRE

EPYTEKARB EPYTEKARB EPYTEKARB EPYTEKARB EPYTEKARB 091B 091B 091B 091B 091B 003B 003B 003B 003B 003B 054B 054B 054B 054B 054B 007B 007B 007B 007B 007B 0011B 0011B 0011B 0011B 0011B 0081B 0081B 0081B 0081B 0081B 0082B 0082B 0082B 0082B 0082B

EPYTROTOM EPYTROTOM EPYTROTOM EPYTROTOM EPYTROTOMERM-RM

061-521 061-521 061-521 061-521 061-521091

003-052 003-052 003-052 003-052 003-052033

054-053 054-053 054-053 054-053 054-053005

007-006 007-006 007-006 007-006 007-006008

0041-0011 0041-0011 0041-0011 0041-0011 0041-0011 0081-0061 0081-0061 0081-0061 0081-0061 0081-00610012

0082-0042 0082-0042 0082-0042 0082-0042 0082-00420013



EPYTEKARB EPYTEKARB EPYTEKARB EPYTEKARB EPYTEKARB 1L1L1L1L1L 2L2L2L2L2L 3L3L3L3L3L 4L4L4L4L4L 5L5L5L5L5L 6L6L6L6L6L 7L7L7L7L7L 01L 01L 01L 01L 01L 11L 11L 11L 11L 11L 12L 12L 12L 12L 12L 22L 22L 22L 22L 22L 1D1D1D1D1D 2D2D2D2D2D 3D3D3D3D3D 4D4D4D4D4D 8h8h8h8h8h 5D5D5D5D5D 6D6D6D6D6D 7D7D7D7D7D 9D9D9D9D9D 21D 21D 21D 21D 21D 31D 31D 31D 31D 31D 01T 01T 01T 01T 01T ααααα11111 ααααα22222

091B 121 - 22 41 76 14 3,92 02 27 05 5,53H9-81x2x83N

0845NID052 522 061 - "4/1G '8/3G 5,01 21M

83x23x8B3645NIDxe

82 '03°22 '03°22

003B 631 - 52 51 18 24 5,93 12 68 06 64H9-22x2x84N

0845NID652 232 571 - "4/1G '8/3G 5,01 21M

84x24x8B3645NIDxe

82 '03°22 '03°22

054B 741 - 72 51 79 5,94 63 42 001 47 5,65H9-71x3x55N

0845NID692 662 091 - "4/1G '8/3G 5,31 21M

45x64x8B3645NIDxe

82 '03°22 '03°22

007B 271 - 82 51 101 55 64 52 501 87 26H9-81x3x06N

0845NID023 092 022 - "4/1G '8/3G 5,31 21M

06x25x8B3645NIDxe

82 '03°22 '03°22

0011B 881 02 62 42 711 17 5,35 84 021 88 27H9-22x3x07N

0845NID063 033 052 021 "4/1G

-61M5,1x

51 21M27x26x8B3645NIDxe

82 °0 °0

0081B 612 - 82 12 231 5,36 5,85 43 531 001 97H9-52x3x08N

0845NID324 083 092 - "4/1G '2/1G 5,71 21M

28x27x01B3645NIDxe

82 '03°22 '03°22

0082B 362 - 03 42 351 78 76 5,24 561 021 99H9-12x4x09N

0845NID494 044 533 - "4/1G '2/1G 91 21M

29x28x01B3645NIDxe

82 '03°22 '03°22

Same dimensionsstandard male splinedshaft version "N1"(see page 26)

ααααα1, ααααα2 Corresponding angles to the release ports 1 and 2, to case the drain ports 1 and 2

Release portsCase drain ports

Release portsCase drain ports

Case drain portsRelease ports

ø D

2

D7

L1

L11

D1

L10

L6D6

L7

L5L4

ø D

4 h

8

ø D

9

N°

5 H

OL

ES

L2L3

ø D

5

D12

T10

L21L22

ø D

3

ø D

13

33RCOe 1806/07.01

HOLDING BRAKE TECHNICAL DATA - MOTOR TYPE MR - MRE

TECHNICAL DATA (For operation outside these parameters, please consult DENISON Calzoni)

CODE Example: BRAKE - B 450 - N1 V1 **

091B 091B 091B 091B 091B "C"ezisrotomrofekarB

003B 003B 003B 003B 003B "D"ezisrotomrofekarB

054B 054B 054B 054B 054B "E"ezisrotomrofekarB

007B 007B 007B 007B 007B "F"ezisrotomrofekarB

0011B 0011B 0011B 0011B 0011B "G"ezisrotomrofekarB

0081B 0081B 0081B 0081B 0081B "H"ezisrotomrofekarB

0082B 0082B 0082B 0082B 0082B "I"ezisrotomrofekarB

1. BRAKE - B 450 NI V1 **

********** inozlaCnosineDotdevreserecapS

1N1N1N1N1N liolarenim:RBN

*1V *1V *1V *1V *1V slaesMPF

1U1U1U1U1U )ekarbrof(laestfahsoN

inozlaCNOSINEDtcatnocesaelp* inozlaCNOSINEDtcatnocesaelp* inozlaCNOSINEDtcatnocesaelp* inozlaCNOSINEDtcatnocesaelp* inozlaCNOSINEDtcatnocesaelp*

3. BRAKE - B 450 - N1 V1 **

1N1N1N1N1N )62egapees(3645NIDxeenilpS

*1D *1D *1D *1D *1D )62egapees(0845NIDenilpS

*1F *1F *1F *1F *1F )72egapees(0845NIDenilpselameF

inozlaCNOSINEDtcatnocesaelp* inozlaCNOSINEDtcatnocesaelp* inozlaCNOSINEDtcatnocesaelp* inozlaCNOSINEDtcatnocesaelp* inozlaCNOSINEDtcatnocesaelp*

2. BRAKE - B 450 - N1 V1 **

4. BRAKE - B 450 - N1 V1 **

BRAKE TYPE

SHAFT

SEALS

SPECIAL



SCITSIRETCARAHC SCITSIRETCARAHC SCITSIRETCARAHC SCITSIRETCARAHC SCITSIRETCARAHCEPYTEKARB EPYTEKARB EPYTEKARB EPYTEKARB EPYTEKARB

091B 091B 091B 091B 091B 003B 003B 003B 003B 003B 054B 054B 054B 054B 054B 007B 007B 007B 007B 007B 0011B 0011B 0011B 0011B 0011B 0081B 0081B 0081B 0081B 0081B 0082B 0082B 0082B 0082B 0082B

EUQROTGNIKARBCITATS EUQROTGNIKARBCITATS EUQROTGNIKARBCITATS EUQROTGNIKARBCITATS EUQROTGNIKARBCITATS mNmNmNmNmN 0521 0081 0562 0004 0026 00411 00171

EUQROTGNIKARBCIMANYD EUQROTGNIKARBCIMANYD EUQROTGNIKARBCIMANYD EUQROTGNIKARBCIMANYD EUQROTGNIKARBCIMANYD mNmNmNmNmN 078 0021 0541 0022 0024 0526 00021

ERUSSERPESAELER ERUSSERPESAELER ERUSSERPESAELER ERUSSERPESAELER ERUSSERPESAELER rab rab rab rab rab 82 82 72 72 72 03 03

ERUSSERPGNITAREPO.XAM ERUSSERPGNITAREPO.XAM ERUSSERPGNITAREPO.XAM ERUSSERPGNITAREPO.XAM ERUSSERPGNITAREPO.XAM rab rab rab rab rab 024 024 024 024 024 024 024

STRAPGNITATORFOAITRENIFOTNEMOM STRAPGNITATORFOAITRENIFOTNEMOM STRAPGNITATORFOAITRENIFOTNEMOM STRAPGNITATORFOAITRENIFOTNEMOM STRAPGNITATORFOAITRENIFOTNEMOM mgK mgK mgK mgK mgK 22222 7400,0 2600,0 920,0 340,0 160,0 02,0 72,0

THGIEW THGIEW THGIEW THGIEW THGIEW gKgKgKgKgK 23 93 45 47 001 851 262

ERMRMEPYTROTOM ERMRMEPYTROTOM ERMRMEPYTROTOM ERMRMEPYTROTOM ERMRMEPYTROTOM521061091

052003033

053054005

006007008

00110041

006100810012

004200820013

34RCOe 1806/07.01

INSTALLATION NOTES - MOTOR TYPE MR - MRE

Mounting

Any mounting position- Note the position of the case drain port

(see below)

Install the motor properly- Mounting surface must be flat and resistant

to bending

Min. tensile strength of mounting screws toDIN 267 Part 3 class 10.9

- Note the prescribed fastening torque

Pipes, pipe connections

Use suitable screws!- Depending on type of motor use either

threaded or flange connection

Choose pipes and hoses suitable for the installation- Please note manufacturing data!

Before operation fill with hydraulic fluid- Use the prescribed filter!

Coupling

- Mounting with screws- Use threaded bore in

the drive shaft- Take apart with extractor

NOTE: Two of the mounting screws must be precisely located/fitted if operation is started and stopped frequently or if highreversible frequencies exist.

Note: Position the case drain pipe, so thatthe motor cannot run empty.

T = SealY = Motor housing feeding line

= Bleed

Curved tooth couplinghub

Screw to remove thecoupling hub

*****

*)

Bleed point

(release to bleed)

Low pressure case drain returns to tank. Low pressure case drain returns to tank.

Motors without shaft seal used with brake

Tank located in higher position

N° 2 lockingscrew forbleed point(on enquiry)

*) Special designs for applications, where the equipmentneeds to be filled with oil.(e.g. in a salty atmosphere)

DRAIN AND FLUSHING LINK INSTALLATION EXAMPLES

Flushing p max= 5 bar Flushing p max= 5 bar

Cooling circuit for high power continuousoperation

Bleed screw(on enquiry)

Installation instructions for motorsof the series "MR - MRE"

Installation instructions for motorsof the series "MR - MRE with brakes"

Bleed point

Cooling circuit for high power continuous operation



35RCOe 1806/07.01

ORDERING CODE - MOTOR TYPE MR - MRE

CODE Example: MR 160C - N1 M1 F1 N1 N **

RMRMRMRMRM suounitnoc.xamrab052dradnats

ERM ERM ERM ERM ERM suounitnoc.xamrab012dednapxe

1. MR 160C - N1 M1 F1 N1 N **

1N1N1N1N1N )62egapees(3645NIDxeenilps

1D1D1D1D1D )62egapees((0845NIDenilps

1F1F1F1F1F )72egapees(0845NIDenilpselamef

1P1P1P1P1P )72egapees(yekhtiwtfahs

1B1B1B1B1B )62egapees(0553.S.Benilps

3. MR 160C - N1 M1 F1 N1 N **

1N1N1N1N1N enon

1Q1Q1Q1Q1Q )82egapees(evirdredocne

1C1C1C1C1C )82egapees(evirdretemohcatlacinahcem

1T1T1T1T1T )82egapees(evirdrotarenegohcat

1M1M1M1M1M redocnesiclElatnemercni)82egapees()ver/eslup005(

lanoitcerid-inU

1B1B1B1B1B lanoitcerid-iB

4. MR 160C - N1 M1 F1 N1 N **

1N1N1N1N1N liolarenimRBN

1F1F1F1F1F laestfahsrab51,RBN

1V1V1V1V1V slaesMPF

1U1U1U1U1U )ekarbrof(laestfahson

5. MR 160C - N1 M1 F1 N1 N **

NNNNN )Bnitelni:WCC,Anitelni:WC(noitatordradnats

SSSSS )Anitelni:WCC,Bnitelni:WC(noitatordesrever

7. MR 160C - N1 M1 F1 N1 N **

1N1N1N1N1N enon

1C1C1C1C1C )03egapees(inozlaCNOSINEDdradnats

1S1S1S1S1S )03egapees(cirtemEASdradnats

1T1T1T1T1T )03egapees(CNUEASdradnats

1G1G1G1G1G )03egapees(cirtemisp0006EAS

1L1L1L1L1L )03egapees(CNUisp0006EAS

6. MR 160C - N1 M1 F1 N1 N **

********** inozlaCnosineDotdevreserecaps8. MR 160C - N1 M1 F1 N1 N **

SERIES

SIZE & DISPLACEMENT

SHAFT

SPEED SENSOR OPTION

SEALS

CONNECTION FLANGE

ROTATION

SPECIAL



AAAAAedoc A33RM A33RM A33RM A33RM A33RM A75RM A75RM A75RM A75RM A75RM

mC 3 1,23 4,65

BBBBBedoc B37RM B37RM B37RM B37RM B37RM B39RM B39RM B39RM B39RM B39RM B011RM B011RM B011RM B011RM B011RM

mC 3 6,27 6,29 0,901

CCCCCedoc C521RM C521RM C521RM C521RM C521RM C061RM C061RM C061RM C061RM C061RM C091RM C091RM C091RM C091RM C091RM

mC 3 7,421 7,951 6,191

DDDDDedoc D002RM D002RM D002RM D002RM D002RM D052RM D052RM D052RM D052RM D052RM D003RM D003RM D003RM D003RM D003RM D033ERM D033ERM D033ERM D033ERM D033ERM

mC 3 2,991 9,052 1,403 4,233

EEEEEedoc E053RM E053RM E053RM E053RM E053RM E054RM E054RM E054RM E054RM E054RM E005ERM E005ERM E005ERM E005ERM E005ERM

mC 3 5,943 6,154 9,794

FFFFFedoc F006RM F006RM F006RM F006RM F006RM F007RM F007RM F007RM F007RM F007RM F008ERM F008ERM F008ERM F008ERM F008ERM

mC 3 9,706 9,607 2,408

GGGGGedoc G0011RM G0011RM G0011RM G0011RM G0011RM G0041ERM G0041ERM G0041ERM G0041ERM G0041ERM

mC 3 8,5211 5,9631

HHHHHedoc H0061RM H0061RM H0061RM H0061RM H0061RM H0081RM H0081RM H0081RM H0081RM H0081RM H0012ERM H0012ERM H0012ERM H0012ERM H0012ERM

mC 3 4,8951 6,9081 2,1902

IIIIIedoc I0042RM I0042RM I0042RM I0042RM I0042RM I0082RM I0082RM I0082RM I0082RM I0082RM I0013ERM I0013ERM I0013ERM I0013ERM I0013ERM

mC 3 0,3932 0,2972 7,3013

LLLLLedoc L0063RM L0063RM L0063RM L0063RM L0063RM L0054RM L0054RM L0054RM L0054RM L0054RM L0045ERM L0045ERM L0045ERM L0045ERM L0045ERM

mC 3 8,6363 7,2054 2,1045

MMMMMedoc M0056RM M0056RM M0056RM M0056RM M0056RM M0007RM M0007RM M0007RM M0007RM M0007RM M0028ERM M0028ERM M0028ERM M0028ERM M0028ERM

mC 3 5,0646 2,7696 4,6228

2. MR 160C - N1 M1 F1 N1 N **

36RCOe 1806/07.01

SALES AND SERVICE LOCATIONS WORLDWIDE - MOTOR TYPE MR - MRE



International Distributors In Europe : Cyprus Czech Republic Greece Hungary Iceland Jugosavia Norway Portugal Poland Romania Russia Slovakia Slovenia Switzerland The Faroe Islands Turkey In Africa : Algeria Egypt Ivory Coast Morocco Nigeria South Africa Tunisia In Middle East : Bahrein Iran Israel Jordan Kuwait Lebanon Pakistan Qatar Saudi Arabia Syria United Arab Emirates In Far East : Indonesia Korea Malaysia New Zealand Philippines Thailand South-America : Argentina Brazil Chile Colombia Ecuador Mexico Peru Venezuela Denison Calzoni S.p.a. Via Caduti di Sabbiuno 15/17 40011 Anzola dell’Emilia Bologna Italy Tel: +39 (051) 6501611 Fax: +39 (051) 736221 e-mail: [email protected]

Asia-Pacific

Australia

Denison Hydraulics PTY 41-43 St Hilliers Road P.O.Box 192 Auburn N.S.W. 2144, Australia Tel : +61 (2) 9646 5200 Fax : +61 (2) 9643 1305

Hong Kong

Denison Hydraulics Ltd. Unit 6A, 33/F Cable TV Tower 9 Hoi Shing Road, Tsuen Wan NT, Hong Kong Tel : +852 2498 8381 Fax : +852 2499 1522

Japan

Denison Japan Inc. 4-2-1 Tsujido-Shinmachi Fujisawa 251, Japan Tel : +81 (466) 35-3050 Fax : +81 (466) 35-2019

China

Denison Hydraulics Engineering Ltd. Room 8018, No. 601, Zhang Yang Road Pudong New Area Shanghai 200120, China Tel : +86 (21) 58205042/58205034 Fax : +86 (21) 58205014

Singapore

Denison Hydraulics LTD 11 Lorong Tukang Dua, Singapore 2261 Tel : +65 268 7840 Fax : +65 268 7847

Taiwan

Denison Hydraulics LTD 6F-10. No. 79,Sec. 2 Roosevelt Road, Taipei Tel : +65 268 7840 Fax : +65 268 7847

Europe

Austria

Denison Hydraulics GmbH Zweigneiderlassung Linz Haibachstraße 69 4061 Pasching, Austria Tel : +43 (72 29) 48 87 Fax : +43 (72 29) 6 30 92

Benelux

Denison Hydraulics Benelux B.V. Pascalstraat 100 3316 GR Dordrecht, Holland Tel : +31 (78) 6179 900 Fax : +31 (78) 6175 755

Denmark

Denison Hydraulics Denmark A/S Industrikrogen 2 2635 Ishöj, Denmark Tel : +45 (4371) 15 00 Fax : +45 (4371) 15 16

Finland

Denison Lokomec Polunmäenkatu 22 P.O.Box 116 33721 Tampere, Finland Tel : + 358 (3) 3575 100 Fax : + 358 (3) 3575 111

France

Denison Hydraulics S.A. 14 route du bois blanc BP 539 18105 Vierzon, France Tel : +33 (2) 48 53 01 20 Fax : +33 (2) 48 75 02 91

Great Britain

Denison Hydraulics UK LTD Kenmore road Wakefield 41, Industrial Park Wakefield, WF2 OXE West Yokshire, England Tel : +44 (1924) 826 021 Fax : +44 (1924) 826 146

Germany

Denison Hydraulik GmbH. Auf dem Sand 14 D-40721 Hilden Tel : +49 (2103) 940 300 Fax : +49 (2103) 940 558

Italy

Denison Hydraulics Srl Via Le Europa 68 20090 Cusago (MI), Italy Tel : +39 (02) 90330-1 Fax : +39 (02) 90390694/5/6

Denison Calzoni S.p.A Via Caduti di Sabbiuno15/17 40011 Anzola dell'Emilia Bologna, Italy Tel : +39 (051) 6501611 Fax : +39 (051) 736221

Spain

Denison Hydraulics S.A. Gomis 1 08023 Barcelona, Spain Tel : +34 (93)253 1919 Fax : +34 (93) 211 6507

Sweden

Denison Hydraulics Svenska AB Sporregatan 13

213 77 - Malmö, Sweden Tel : +46 (40) 600 13 00 Fax : +46 (40) 600 13 50

North America

Canada

Denison Hydraulics Canada Inc. 2320-1 Bristol Circle, Unit 1 Oakville, ON L6H 5S2, Canada Tel : +1 (905) 829 5800 Fax : +1 (905) 829 5805

Mexico, Central America, South America, Caribbean countries

Denison Hydraulics Corp. 6167 NW 181 Terrace Circle North Miami, FL 33015, USA Tel : +1 (305) 362 2246 Fax : +1 (305) 362 2246

USA

Denison Hydraulics Corp. 14249 Industrial Parkway Marysville, OH 43040, USA Tel : +1 (937) 644 3915 Fax : +1 (937) 642 3738

Others

Other European, Middle East, African countries

Denison Hydraulics S.A. 14 route du bois blanc BP 538 18105 Vierzon, France Tel : +33 (2) 48 53 01 20 Fax : +33 (2) 48 53 01 46

Your local Denison Hydraulics representative

DENISON CALZONI Radial Piston Motor Type MR, MRE Hydraulics/02 - Radial... · Radial Piston Motor...

Documents

Transcript of DENISON CALZONI Radial Piston Motor Type MR, MRE Hydraulics/02 - Radial... · Radial Piston Motor...