Demonstration of Part Number - yhmco.com.t Male (GMW) Nut Female (NF) Not designed for gasket...
Transcript of Demonstration of Part Number - yhmco.com.t Male (GMW) Nut Female (NF) Not designed for gasket...
Nut, Caps, and Plugs
(NF) Nut Female
(NM) Nut Male
(NMS) Nut Male Short
(CP) Cap Female
(PL) Plug Male
Description Page Description Page
General Introduction
Installation Instructions
Feature
Technical Specification and Designation
Demonstration of Part Number
Tubing Specifications For FS Fittings
Glands
(GFW) Gland Female
(GMW) Gland Male
01
01
02
03
04
04
05
06
07
08
08
09
09
09
10
Contents
High-Flow Connections
(HFGM, HFGMS) High Flow Gland
(HFNF) High Flow Nut Female
(HFNM) High Flow Nut Male
10
11
11
11
Gaskets
(GAP) Gasket EP Finish
(GRP) Gasket Retained Assembly EP Finish
(GBP) Gasket Blind EP Finish
(GAS) Gasket Silver Plated
(GRS) Gasket Retained Assembly Silver Plated
(GBS) Gasket Blind Silver Plated
12
12
13
13
13
14
14
Face Seal to ISO-KF Flange Adaptor
(VKF) Female Nut Adaptor
(VKM) Male Nut Adaptor
15
15
16
DA
JA
Face Seal Fittings
Feature
General Introduction
Installation Instructions
DAJA’s Metal Gasket Face Seal Fittings (FS fitting) contains five major precision machined parts. One completed assembly of the connection includes nut female, gland female, gasket, gland male and nut male. A photo for one set of assembly is showed below.
1. Assembly the Male Gland with Male Nut, then butt-weld with the tube.
3. Install the Gasket on the toroid of Gland.
5. Tighten the nut to one-eighth turn with wrenches.
2. Assembly the Female Gland with Female Nut, then butt-weld with the tube.
4. Tighten slightly with fingers.
1/8 turn (45°)
● DAJA FS fitting is a high performance leak-tight seal fittings for high purity gas piping, and high vacuum piping application.
● Installing and removing the connection can be performed with minimum clearance.● The inside surface of the nut female is silver plated to prevent galling, ensure easy assembly and
consistent make-up.● Weld Parts are made of SCQ SUS316L VAR or VIM+VAR which is precision machined for high purity
welding.● DAJA fittings are individually vacuum packed in the certified class 100 clean room after being ultra clean
washed and protection applied to the seals.● Product package is labeled with an identification label containing fitting type, description, heat code, and
production batch number for tracing.
● Note: SCQ : Semi-conductor clean quality.
FS FittingsFS Fittings
- 1 - - 2 -
DA
JA
Technical Specification and Designation Demonstration of Part Number
Tubing Specifications for FS Fittings
Material Designation
Surface Roughness Designation (Wetted Area)
Cleaning & Packaging Designation
Pressure Rating DesignationAll data shown as on this catalogue is for the temperature ranging from 20℉ to 100℉ (-25℃ to 36℃).
Designator Material Specification
D 316L VIM+VAR Stainless Steel
Bar stock meets the standard ofASTM A479, ASME SA479, ASTM A276.
Forged body meets the standard of ASTM A182, ASME SA182, ASTM A314.
S 316L VAR or VOD Stainless Steel
L 316L Stainless Steel
6 316 Stainless Steel
4 304 Stainless Steel
N Nickel
Designator Process Description Specification
E EP, electro-polishing Ra5μin (Ra0.13μm)
B BA, mechanical processing Ra10μin (Ra0.25μm)
M Machining mill finish
S Silver plating over thread area mill finish
Product Category Designation Specification
Glands UHP DAJA spec, SOP-8-57
Gaskets UHP DAJA spec, SOP-8-57
Nuts, Caps, and Plugs HP DAJA spec, SOP-8-58
High-Flow Connections HP DAJA spec, SOP-8-58
Face Seal to ISO-KF Flange Adaptor HP DAJA spec, SOP-8-58
ProductCategory Description Product
Code EP 5Ra Finish BA 10Ra Finish or Mill Finish
GlandsGland Female GFW GFW19-1/2-1/2-SE GFW19-1/2-1/2-SB
Gland Male GMW GMW10-1/4-1/4-SE GMW10-1/4-1/4-SB
Nuts, Caps, and Plugs
Nut Female NF NF-1/2-6S
Nut Male NM NM-1/2-6M
Nut Male Short NMS NMS14-1/4-6M
Cap Female CP CP-1/2-6S
Plug Male PL PL-1/2-6M
High-Flow Connections
High Flow Gland HFGM, HFGMS HFGM30-1/4-3/8-SE HFGM30-1/4-3/8-SB
High Flow Nut Female HFNF HFNF-1/4-12-6S
High Flow Nut Male HFNM HFNM-1/4-10-6M
Gaskets
Gasket Silver Plated GAS GAS-1/4-LS
Gasket EP Finish GAP GAP-1/4-NE
Gasket Retainer Assembly Silver Plated GRS GRS-1/4-LS
Gasket Retainer Assembly EP Finish GRP GRP-1/4-NE
Gasket Blind Silver Plated GBS GBS-1/4-NS
Gasket Blind EP Finish GBP GBP-1/4-LE
Face Seal to ISO-KFFlange Adaptor
Male Nut Adaptor VKM VKM1614-4B
Female Nut Adaptor VKF VKF1638-4B
● Note : 1. J is Asian design and specification.2. A is American design and specification.
OD (inch) OD (mm)Wall Thickness (mm)
Manufacturing Standard*J *A
1 / 4 ” 6.35 1.00 0.89 JIS G3459/ ASTM standard (A270, A269)
3 / 8 ” 9.53 1.00 0.89 JIS G3459/ ASTM standard (A270, A269)
1 / 2 ” 12.70 1.24 1.24 JIS G3459/ ASTM standard (A270, A269)
3 / 4 ” 19.05 1.24 1.65 JIS G3459/ ASTM standard (A270, A269)
1” 25.40 1.65 1.65 JIS G3459/ ASTM standard (A270, A269)
FS FittingsFS Fittings
- 3 - - 4 -
DA
JA
Gland Female (GFW)
DAJAPart No.
FS Sizein.
TubeSize
Dimensions InterchangePart No.1
InterchangePart No.2
Working Pressure
A C E Ni SS
Dimensions, in. (mm) psig (bar)
GFW19-1/8-1/8-XX 1/81/8
1.08(27.4) 0.75
(19.1)0.06(1.5)
6LV-2-VCR-3S-2TB7 2-2 V1T3-* 1.08 8500(585)
8500(585)
GFW19-1/4-1/8-XX 1/4 1.10(27.9) 6LV-4-VCR-3S-2TB7 -
5100(351)
5100(351)
GFW6-1/4-1/4-XX 1/4
1/4
0.60(15.2)
0.25(6.4)
0.18(4.6)
6LV-4-VCR-3S-4TB2 4-4 V1M-* .035
5100(351)
5100(351)GFW10-1/4-1/4-XX 1/4 0.72
(18.3)0.38(9.6) 6LV-4-VCR-3S-4TB3 4-4 V1TW-* .72
GFW19-1/4-1/4-XX 1/4 1.10(27.9)
0.75(19.1) 6LV-4-VCR-3S-4TB7 4-4 V1T3-* 1.10
GFW19-1/2-1/4-XX 1/2 1.12(28.4)
0.75(19.1) 6LV-8-VCR-3S-4TB7 8-4 V1T3-* 1.12 3500
(241)4300(296)
GFW6-1/2-3/8-XX 1/23/8
0.62(15.7)
0.25(6.4) 0.31
(7.9)
6LV-8-VCR-3S-6TB2 8-6 V1M-* .623300(227)
3300(227)
GFW19-1/2-3/8-XX 1/2 1.12(28.4)
0.75(19.1) 6LV-8-VCR-3S-6TB7 8-6 V1T3-* 1.12
GFW6-1/2-1/2-XX 1/2
1/2
0.62(15.7)
0.25(6.4)
0.40(10.2)
6LV-8-VCR-3S-8TB2 8-8 V1M-* .049
3500(241)
3500(241)GFW10-1/2-1/2-XX 1/2 0.74
(18.8)0.38(9.6) 6LV-8-VCR-3S-8TB3 8-8 V1TW-* .74
GFW19-1/2-1/2-XX 1/2 1.12(28.4)
0.75(19.1) 6LV-8-VCR-3S-8TB7 8-8 V1T3-* 1.12
Not designed for gasket retainer assembly.
GlandsGlands
- 5 - - 6 -
Description Code DAJA Part NO.
Gland Female GFW GFW19-1/2-1/2-SB
Gland Male GMW GMW10-1/4-1/4-DB
Sleeve Length 1FS Size Tube Size
Material Inner SurfaceQuality Standard
(in.) (in.) (mm)
Weld leg length 1 / 8 1/16 M6=6 D = 316L VIM/VAR E=EP finish, Ra 5A = American/ Europe Standard
6 =6.40mm 1 / 4 1/8 M8=8 S = 316L VAR B=BA finish, Ra 10
9=9.10mm 1 / 2 1/4 M10=10 L = 316L M=Mill finish
10=9.60mm 5 / 8 3/8 M12=12 6 = 316 J = JIS Standard19=19.10mm 3 / 4 1/2 M18=18
1 3/4 D = DAJA Standard1
DA
JA
GlandsHow to Order A Part Example: GMW19-1/4-1/4-DE-A
GMW19 Gland Male with (3/4”) 19.1mm orbital welding leg
1/4 FS face sealing head dimensions is 1/4” OD
1/4 tube end dimension is 1/4” OD
DE D: 316L VIM/VAR Material, E: Electro-polishing finish, 5 Ra
A American/Europe Standard
Gland Male (GMW)
Nut Female (NF)
Not designed for gasket retainer assembly.May contain internal diameter transitions.
DAJAPart No.
FS Size in.
TubeSize
Dimensions InterchangePart No.1
InterchangePart No.2
Working Pressure
A C E Ni SS
Dimensions, in. (mm) psig (bar)
GMW19-1/8-1/8-XX 1/8 1/8 1.42(36.1)
0.75(19.1)
0.06 (1.5) 6LV-2-VCR-3-2TB7 2-2 V1T3-* 1.42 8500
(585)8500(585)
GMW6-1/4-1/4-XX 1/4
1/4
1.20(30.5)
0.25(6.4)
0.18(4.6)
6LV-4-VCR-3-4TB2 4-4 V1M-* 1.20
5100(351)
5100(351)
GMW9-1/4-1/4-XX 1/4 1.31(33.3)
0.36(9.1) 6LV-4-VCR-3-02205 4-4 V1T3-*
GMW10-1/4-1/4-XX 1/4 1.32(33.5)
0.38(9.6) 6LV-4-VCR-3-4TB3 4-4 V1TW-* 1.32
GMW19-1/4-1/4-XX 1/4 1.70(43.2)
0.75(19.1) 6LV-4-VCR-3-4TB7 4-4 V1T3-* 1.70
GMW19-1/2-1/4-XX 1/2 1.80(45.7)
0.75(19.1) 6LV-8-VCR-3-4TB7 8-4 V1T3-* 1.79 3500
(241)4300(296)
GMW6-1/2-3/8-XX 1/2
3/8
1.29(32.8)
0.25(6.4) 0.31
(7.9)
6LV-8-VCR-3-6TB2 8-6 V1M-* 1.293300(227)
3300(227)
GMW19-1/2-3/8-XX 1/2 1.79(45.5)
0.75(19.1) 6LV-8-VCR-3-6TB7 8-6 V1T3-* 1.79
GMW6-1/2-1/2-XX 1/2
1/2
1.29(32.8)
0.25(6.4)
0.40(10.2)
6LV-8-VCR-3-8TB2 8-8 V1M-* 1.29
3500(241)
3500(241)GMW10-1/2-1/2-XX 1/2 1.41
(35.8)0.38(9.6) 6LV-8-VCR-3-8TB3 8-8 V1TW-* 1.41
GMW19-1/2-1/2-XX 1/2 1.79(45.5)
0.75(19.1) 6LV-8-VCR-3-8TB7 8-8 V1T3-* 1.79
GMW19-3/4-3/4-XX 3/4 3/4 2.03(51.6)
0.75(19.1)
0.65(16.5) 6LV-12-VCR-3-12TB7 12-12 V1T3-* 2.03 2400
(165)2400(165)
GMW19-1-1-XX 1 1 2.32(58.9)
0.75(19.1)
0.87(22.1) 6LV-16-VCR-3-16TB7 16-16 V1T3-* 2.32 2400
(165)2400(165)
Nuts, Caps, and PlugsGlands
DAJAPart No. FS Size
Dimensions InterchangePart No.1
InterchangePart No.2A F TX
Dimensions, in. (mm)
NF-1/8-6S 1/8 0.53(13.5) 7/16 0.21
(5.3) SS-2-VCR-1 2 BV-SS
NF-1/4-6S 1/4 0.81(20.6) 3/4 0.36
(9.1) SS-4-VCR-1 4 BV-SS-D
NF-1/2-6S 1/2 0.88(22.4) 1 1/16 0.61
(15.5) SS-8-VCR-1 8 BV-SS
NF-5/8-6S 5/8 0.88(22.4) 1 3/16 0.74
(18.8) SS-10-VCR-1 -
NF-3/4-6S 3/4 1.12(28.4) 1 1/2 0.89
(22.6) SS-12-VCR-1 12 BV-SS
NF-1-6S 1 1.34(34.0) 1 3/4 1.20
(30.5) SS-16-VCR-1 16 BV-SS
- 7 - - 8 -
DA
JA
Nuts, Caps, and Plugs How to Order A PartExample:NW-1/4-6M-A
NM Nut Male
1/4 FS face sealing head dimension is 1/4” OD
6M 6: 316 Material, M: Mill finish
A American/Europe Standard
A American/Europe Standard
Description Code DAJA Part NO.
Nut Female NF NF-1/2-6S
Nut Male NM NM-1/2-6M
Nut Male Short NMS NMS14-1/4-6M
Cap Female CP CP-1/2-6S
Plug Male PL PL-1/2-6M
Sleeve Length 1FS Size
Material Inner Surface Quality Standard
(in.)
Total length 1/8 6 = 316 M=Mill finish A = American/Europe Standard14 = 13.70 mm 1/4 S =Sliver Plated
17 = 16.50 mm 1/2J = JIS Standard
(↑only for nut male short) 5/8
3/4D = DAJA Standard
1
High-Flow ConnectionsNuts, Caps, and Plugs
Nut Male (NM) Plug Male (PL)
Cap Female (CP)
Nut Male Short (NMS)
DAJAPart No.
FS Size
Dimensions InterchangePart No.1
InterchangePart No.2A F TX
Dimensions, in. (mm)
NM-1/8-6M 1/8 0.50(12.7) 3/8 0.21
(5.3) SS-2-VCR-4 2 BVI-SS
NM-1/4-6M 1/4 0.71(18.0) 5/8 0.36
(9.1) SS-4-VCR-4 4 BVI-SS
NM-1/2-6M 1/2 0.81(20.6) 15/16 0.61
(15.5) SS-8-VCR-4 8 BVI-SS
NM-5/8-6M 5/8 0.81(20.6) 1 1/16 0.74
(18.8) SS-10-VCR-4 -
NM-3/4-6M 3/4 1.00(25.4) 1 5/16 0.89
(22.6) SS-12-VCR-4 12 BVI-SS
NM-1-6M 1 1.19(30.2) 1 5/8 1.20
(30.5) SS-16-VCR-4 16 BVI-SS
DAJAPart No.
FS Size
Dimensions InterchangePart No.1
InterchangePart No.2A C F
Dimensions, in. (mm)
CP-1/8-6S 1/8 0.63(16.0)
0.30(7.6) 7/16 SS-2-VCR-CP -
CP-1/4-6S 1/4 0.94(23.9)
0.44(11.2) 3/4 SS-4-VCR-CP 4 FNV-SSR
CP-1/2-6S 1/2 1.01(25.6)
0.45(11.4) 1 1/16 SS-8-VCR-CP 8 FNV-SSR
CP-3/4-6S 3/4 1.29(32.8)
0.54(13.7) 1 1/2 SS-12-VCR-CP 12 FNV-SSR
CP-1-6S 1 1.54(39.1)
0.63(16.0) 1 3/4 SS-16-VCR-CP 16 FNV-SSR
DAJAPart No.
FS Size
Dimensions InterchangePart No.1
InterchangePart No.2A F TX
Dimensions, in. (mm)
NMS14-1/4-6M 1/4 0.54(13.7) 5/8 0.36
(9.1)SS-4-VCR-4-
.54NC 4 BVI .54-SS
NMS17-1/4-6M 1/4 0.65(16.5) 5/8 0.36
(9.1)SS-4-VCR-4-
.65NC 4 BVI.65-SS
Option: A taper at the hex end allows the nut to move around 90。Tube bends. Not designed for gasket retainer assembly.
For use with short gland.
DAJAPart No. FS Size
Dimensions InterchangePart No.1
InterchangePart No.2A F
Dimensions, in. (mm)
PL-1/8-6M 1/8 0.68(17.3) 3/8 SS-2-VCR-P 2 PNV-SSR
PL-1/4-6M 1/4 0.92(23.4) 5/8 SS-4-VCR-P 4 PNV-SSR
PL-1/2-6M 1/2 1.08(27.4) 15/16 SS-8-VCR-P 8 PNV-SSR
PL-3/4-6M 3/4 1.43(36.3) 1 5/16 SS-12-VCR-P 12 PNV-SSR
PL-1-6M 1 1.52(38.6) 1 5/8 SS-16-VCR-P 16 PNV-SSR
- 9 - - 10 -
DA
JA
High-Flow ConnectionsHow to Order A PartExample: HFGM30-1/4-3/8-SB-D
HFGM30 High Flow Gland, 30: Total gland length
1/4 FS face sealing head dimensions is 1/4” OD
3/8 Tube end dimensions is 3/8” OD
SB S: 316L VAR Material, B: mechanical processing finish, 10 Ra
D DAJA Standard
Description Code DAJA Part NO.
High Flow Gland HFGM, HFGMS HFGM30-1/4-3/8-SB
High Flow Nut Female HFNF HFNF-1/4-12-6S
High Flow Nut Male HFNM HFNM-1/4-10-6M
Sleeve Length 1FS
SizeTube Size Sleeve Length 2 Material Inner Surface
Quality Standard(in.) (in.)
Total length 1 / 4 3 / 8 Tx S = 316L VAR B=BA finish, Ra 10 A = American/
Europe Standard5=15.20mm 10= 9.90mm L = 316L E=EP finish, Ra 5
19=19.10mm 12=11.70mm 6 = 316 M=Mill finishJ = JIS Standard
30=30.20mm (↑only for High Flow Nut
Series)
S=Sliver Plated
33=33.30mm D = DAJA Standard(↑only for High Flow Gland)
High Flow Gland (HFGM, HFGMS)
GasketsHigh-Flow Connections
DAJAPart No.
FS Size
Tube Size
Dimensions InterchangePart No.1
InterchangePart No.2
Working Pressure
A B E E1 Ni SS
Dimensions, in. (mm) psig (bar)
HFGM30-1/4-3/8-XX 1/4 3/8 1.19(30.2)
1.00(25.4)
0.25(6.4)
0.31(7.9)
6LV-4-HVCR-3-1.19SR 4-6 VH1T3-* 3300
(227)3300(227)
HFGM33-1/4-3/8-XX 1/4 3/8 1.31(33.3)
1.12(28.4)
0.25(6.4)
0.31(7.9)
6LV-4-HVCR-3-1.31SR
4-4 VH1T3-*-1.31
3300(227)
3300(227)
HFGMS15-1/4-3/8-XX 1/4 3/8 0.60(15.2)
0.41(10.4)
0.25(6.4)
0.31(7.9)
6LV-4-HVCR-3-.60SR
4-6 VH1T3-*-.60
3300(227)
3300(227)
HFGMS19-1/4-3/8-XX 1/4 3/8 0.75(19.1)
0.55(14.2)
0.25(6.4)
0.31(7.9)
6LV-4-HVCR-3S-6TB7 -
3300(227)
3300(227)
High Flow Nut Female (HFNF)
High Flow Nut Male (HFNM)
Gasket EP Finish (GAP)
DAJAPart No.
FS Size
Dimensions InterchangePart No.1
InterchangePart No.2A F TX
Dimensions, in. (mm)
HFNF-1/4-10-6S 1/4 0.81(20.6) 3/4 0.39
(9.9) SS-4-HVCR-1SR 4 BVH-SS-D
HFNF-1/4-12-6S 1/4 0.81(20.6) 3/4 0.46
(11.7) SS-4-HVCR-1 -
DAJAPart No.
FS Size
Dimensions InterchangePart No.1
InterchangePart No.2A F TX
Dimensions, in. (mm)
HFNM-1/4-10-6M 1/4 0.71(18.0) 5/8 0.39
(9.9) SS-4-HVCR-4SR 4 BVHI-SS
(Can not be used in a gasket retainer assembly.)
DAJAPart No.
FS Size
Dimensions InterchangePart No.1
InterchangePart No.2E TX
Dimensions, in. (mm)
GAP-1/8-XX 1/8 0.09(2.3)
0.26(6.6) -2-VCR-2-VS 2 VG-N
GAP-1/4-XX 1/4 0.22(5.6)
0.47(11.9) -4-VCR-2-VS 4 VG-N
GAP-1/2-XX 1/2 0.44(11.2)
0.78(19.8) -8-VCR-2-VS 8 VG-N
GAP-5/8-XX 5/8 0.58(14.7)
0.91(23.1) -10-VCR-2-VS -
GAP-3/4-XX 3/4 0.66(16.8)
1.14(29.0) -12-VCR-2-VS 12 VG-N
GAP-1-XX 1 0.89(22.6)
1.40(35.6) -16-VCR-2-VS 16 VG-N
- 11 - - 12 -
DA
JA
Gaskets
Electro-Polished
How to Order A PartExample: GAS-1/4-LS-J
GAS Gasket Silver Plated
1/4 FS face sealing dimensions is 1/4” OD
LS L: 316L Material, S: Silver Plated
J JIS Standard
Description Code DAJAPart NO.
FS Size(in.) Material Inner Surface
Quality Standard
Gasket Silver Plated GAS GAS-1/4-LS 1 / 8 N = Ni E = EP finish, Ra 5
A = American/Europe Standard
Gasket EP Finish GAP GAP-1/4-NE 1 / 4 L = 316L S = Sliver Plated J = JIS Standard
Gasket Retainer AssemblySilver Plated
GRS GRS-1/4-LS 1 / 2 D = DAJA Standard
Gasket Retainer AssemblyEP Finish
GRP GRP-1/4-NE 5 / 8
Gasket Blind Silver Plated GBS GBS-1/4-NS 3 / 4
Gasket Blind EP Finish GBP GBP-1/4-NE 1
Gasket Retained Assembly EP Finish (GRP)(Retainer and gasket must be used as an assembly.)
DAJAPart No.
FS Size
Dimensions InterchangePart No.1
InterchangePart No.2E TX
Dimensions, in. (mm)
GRP-1/4-XX 1/4 0.24(6.1)
0.50(12.7) -4-VCR-2-GR-VS 4 VGR-N
GRP-1/2-XX 1/2 0.44(11.2)
0.79(20.1) -8-VCR-2-GR-VS 8 VGR-N
GRP-3/4-XX 3/4 0.66(16.8)
1.14(29.0)
-12-VCR-2-GR-VS 12 VGR-N
GRP-1-XX 1 0.89(22.6)
1.40(35.6)
-16-VCR-2-GR-VS 16 VGR-N
GasketsGaskets
Gasket Blind EP Finish (GBP)
DAJAPart No. FS Size
Dimensions InterchangePart No.1
InterchangePart No.2TX
Dimensions, in. (mm)
GBP-1/8-XX 1/8 0.26(6.6) -2-VCR-2-VS-BL 2 VG-N-BL
GBP-1/4-XX 1/4 0.47(11.9) -4-VCR-2-VS-BL 4 VG-N-BL
GBP-1/2-XX 1/2 0.78(19.8) -8-VCR-2-VS-BL 8 VG-N-BL
GBP-5/8-XX 5/8 0.91(23.1) -10-VCR-2-VS-BL -
GBP-3/4-XX 3/4 1.14(29.0) -12-VCR-2-VS-BL 12 VG-N-BL
GBP-1-XX 1 1.40(35.6) -16-VCR-2-VS-BL 16 VG-N-BL
Gasket Silver Plated (GAS)
Gasket Retained Assembly Silver Plated (GRS)
Gasket Blind Silver Plated (GBS)
(Can not be used in a gasket retainer assembly.)
(Retainer and gasket must be used as an assembly.)
DAJAPart No.
FS Size
Dimensions InterchangePart No.1
InterchangePart No.2E TX
Dimensions, in. (mm)
GAS-1/8-XX 1/8 0.09(2.3)
0.26(6.6) -2-VCR-2 2 VG-SS
GAS-1/4-XX 1/4 0.22(5.6)
0.47(11.9) -4-VCR-2 4 VG-SS
GAS-1/2-XX 1/2 0.44(11.2)
0.78(19.8) -8-VCR-2 8 VG-SS
GAS-5/8-XX 5/8 0.58(14.7)
0.91(23.1) -10-VCR-2 -
GAS-3/4-XX 3/4 0.66(16.8)
1.14(29.0) -12-VCR-2 12 VG-SS
GAS-1-XX 1 0.89(22.6)
1.40(35.6) -16-VCR-2 16 VG-SS
DAJAPart No.
FS Size
Dimensions InterchangePart No.1
InterchangePart No.2E TX
Dimensions, in. (mm)
GRS-1/4-XX 1/4 0.24(6.1)
0.50(12.7) -4-VCR-2-GR 4 VGR-SS
GRS-1/2-XX 1/2 0.44(11.2)
0.79(20.1) -8-VCR-2-GR 8 VGR-SS
GRS-3/4-XX 3/4 0.66(16.8)
1.14(29.0) -12-VCR-2-GR 12 VGR-SS
GRS-1-XX 1 0.89(22.6)
1.40(35.6) -16-VCR-2-GR 16 VGR-SS
DAJAPart No.
FS Size
Dimensions InterchangePart No.1
InterchangePart No.2TX
Dimensions, in. (mm)
GBS-1/8-XX 1/8 0.26(6.6) -2-VCR-2-BL 2 VG-SS-BL
GBS-1/4-XX 1/4 0.47(11.9) -4-VCR-2-BL 4 VG-SS-BL
GBS-1/2-XX 1/2 0.78(19.8) -8-VCR-2-BL 8 VG-SS-BL
GBS-5/8-XX 5/8 0.91(23.1) -10-VCR-2-BL -
GBS-3/4-XX 3/4 1.14(29.0) -12-VCR-2-BL 12 VG-SS-BL
GBS-1-XX 1 1.40(35.6) -16-VCR-2-BL 16 VG-SS-BLSilver Plated
- 13 - - 14 -
DA
JA
Face Seal to ISO-KF Flange Adaptor Face Seal to ISO-KF Flange Adaptor
- 15 - - 16 -
Female NutAdaptor (VKF)
DAJAPart No.
FlangeISO-KF FS Size
Dimensions InterchangePart No.1
InterchangePart No.2A
Dimensions, in. (mm)
VKF1614-4B NW16 1/4 1.42(36.0) JNWFVCR1614 -
VKF1638-4B NW16 3/8 1.61(41.0) - -
VKF1612-4B NW16 1/2 1.61(41.0) JNWFVCR1650 -
VKF2514-4B NW25 1/4 1.42(36.0) JNWFVCR2514 -
VKF2538-4B NW25 3/8 1.61(41.0) - -
VKF2512-4B NW25 1/2 1.61(41.0) JNWFVCR2550 -
VKF2534-4B NW25 3/4 2.13(54.0) JNWFVCR2575 -
VKF4014-4B NW40 1/4 1.42(36.0) JNWFVCR4014 -
VKF4038-4B NW40 3/8 1.61(41.0) - -
VKF4012-4B NW40 1/2 1.61(41.0) JNWFVCR4050 -
VKF4034-4B NW40 3/4 2.09(53.0) JNWFVCR4075 -
VKF5014-4B NW50 1/4 1.42(36.0) JNWFVCR5014 -
VKF5038-4B NW50 3/8 1.61(41.0) - -
VKF5012-4B NW50 1/2 1.61(41.0) JNWFVCR5050 -
VKF5034-4B NW50 3/4 2.09(53.0) JNWFVCR5075 -
Male Nut Adaptor (VKM)
DAJAPart No.
FlangeISO-KF
FS Size
Dimensions InterchangePart No.1
InterchangePart No.2A
Dimensions, in. (mm)
VKM1614-4B NW16 1/4 1.42(36.0) JNWMVCR1614 -
VKM1638-4B NW16 3/8 1.61(41.0) - -
VKM1612-4B NW16 1/2 1.61(41.0) JNWMVCR1650 -
VKM2514-4B NW25 1/4 1.42(36.0) JNWMVCR2514 -
VKM2538-4B NW25 3/8 1.61(41.0) - -
VKM2512-4B NW25 1/2 1.61(41.0) JNWMVCR2550 -
VKM2534-4B NW25 3/4 2.13(54.0) JNWMVCR2575 -
VKM4014-4B NW40 1/4 1.42(36.0) JNWMVCR4014 -
VKM4038-4B NW40 3/8 1.61(41.0) - -
VKM4012-4B NW40 1/2 1.61(41.0) JNWMVCR4050 -
VKM4034-4B NW40 3/4 2.09(53.0) JNWMVCR4075 -
VKM5014-4B NW50 1/4 1.42(36.0) JNWMVCR5014 -
VKM5038-4B NW50 3/8 1.61(41.0) - -
VKM5012-4B NW50 1/2 1.61(41.0) JNWMVCR5050 -
VKM5034-4B NW50 3/4 2.09(53.0) JNWMVCR5075 -
● Glass bead blasted finish.● Other connectors are available upon request.
DA
JA
Face Seal to ISO-KF Flange AdaptorHow to Order A PartExample: VKF1614-4B-D
VKF Female gland with ISO-KF flange
16 Flange spec.
14 Gland spec.
4B 4: 304 Material, B: Bright-annealing finish, 10 Ra
D DAJA Standard
Description Code DAJA Part NO.
Male Nut Adaptor VKM VKM1614-4B
Female Nut Adaptor VKF VKF1638-4B
Flange Spec.FS Size
Material Inner SurfaceQuality Standard
(in.)
16 = NW16 14 = 1/4" 4 = 304 B = BA finish, Ra 10A = American/Europe Standard
25 = NW25 38 = 3/8”
40 = NW40 12 = 1/2" J = JIS Standard
50 = NW50 34 = 3/4” D = DAJA Standard