DELUGE VALVE AND SKID - PEDINCOpedinco.ir/wp-content/uploads/2017/08/CLA-VAL.pdfA Deluge System can...

10
DELUGE VALVE AND SKID The Deluge system is designed to protect high hazard areas containing a severe fuel hazard with a high heat release rate by bringing a large number of open sprayers into action simultaneously in the event of a fire or in the event of high Temperature to keep equipments and asset on lower temperature. A Deluge System can be activated by the following: 1. Manually (Push Buttons on Control Panel or Local Manual Release Valve) 2. Electrically (F&G Signals ) 3. Pneumatically (Glass Bulb Detectors) 4. Hydraulically (By pass valve) ‐To make sure that the Deluge Valve will be activated on any condition, sometimes more than 1 activating mode are considered. Also Deluge Valves could be supplied on 2 modes: On‐Off Valve Pressure Control Valve (Due to high pressure of Fire Water Pumps or high Pressure Differential on Fire Water Ring Main and Spray Nozzles, it needs to control outlet pressure of Deluge Valve.) Deluge Skid (Customized): A Deluge System can be a simple Valve or Skid mounted along with By‐Pass Line, Isolating Valves, Strainers, Full Test/ Drain Line, Double Inlet / Outlet, Release Monitoring Devices (High Pressure Switch), Release Alarm Device (Hydraulic), Pressure Gages on Upstream and Downstream of Deluge Valve, Pneumatic Line including Air Regulator with by‐pass Line, Air Back‐Up Reservoir, Check Valves, Isolating Valves, Pressure Safety Valve (PSV), Pressure Switch (Low and Low‐Low), Junction Box, Weather Proof Cabinet and Lights AND Heating Sys for cold‐weather places. Material of Construction of Deluge Valve: Main Valve Body & Cover: Ductile Iron ASTM A‐536* UL, ULC Cast Steel ASTM A216‐WCB* UL, ULC Naval Bronze ASTM B‐61 UL, ULC Nickel Aluminum Bronze ASTM B148 UL, ULC Super Duplex Stainless Steel UL, ULC Stainless Steel ASTM A743‐CF‐8M UL, ULC Main Valve Internal Trim: Bronze ASTM B61 Monel QQ‐N‐281 Class B Diaphragm and Disc: Buna‐N® synthetic rubber Material of Construction of Deluge Skid: Depends on location of plant, Seawater and Fresh Water are demanded for fire fighting. Skid Piping should be suitable to withstand against highly corrosive water . Cu‐Ni Piping and Ni‐Al Bronze Deluge Valve are selected for Seawater demanded fire water. As well as Skid and its cabinet is coated with suitable painting to withstand against highly Saliferous and corrosive environment (Marine Environment ) Hazardous Area: On Oil and Gas Projects, all Instrument ( Solenoid Valves, Pressure Switches, Junction Boxes, Control Panels and lightings) and considered suitable for Classified Hazardous Area, Zone1, IIB, T3, IP 65, ZONE 2, EEXD IIB T3 ATEX EEx dm IIC T4, IP65 CERTIFICATES:

Transcript of DELUGE VALVE AND SKID - PEDINCOpedinco.ir/wp-content/uploads/2017/08/CLA-VAL.pdfA Deluge System can...

Page 1: DELUGE VALVE AND SKID - PEDINCOpedinco.ir/wp-content/uploads/2017/08/CLA-VAL.pdfA Deluge System can be activated by the following: 1. Manually (Push Buttons on Control Panel or Local

DELUGE VALVE AND SKID

The  Deluge  system  is  designed  to  protect  high  hazard  areas 

containing  a  severe  fuel  hazard  with  a  high  heat  release  rate  by 

bringing a large number of open sprayers into action simultaneously 

in  the event of a  fire or  in  the event of high Temperature  to keep 

equipments and asset on lower temperature.

A Deluge System can be activated by the following:

1. Manually  (Push  Buttons  on  Control  Panel  or  Local  Manual 

Release Valve)

2. Electrically (F&G Signals ) 

3. Pneumatically (Glass Bulb Detectors) 

4. Hydraulically (By pass valve) 

‐To  make  sure    that  the  Deluge  Valve  will  be  activated  on  any 

condition, sometimes more than 1 activating mode are considered.

Also Deluge Valves could be supplied on 2 modes:

• On‐Off Valve

• Pressure Control Valve (Due to high pressure of Fire Water Pumps 

or  high  Pressure  Differential  on  Fire  Water  Ring  Main  and  Spray 

Nozzles, it needs to control outlet pressure of Deluge Valve.) 

Deluge Skid (Customized):

A Deluge System can be a simple Valve or Skid mounted along with 

By‐Pass Line, Isolating Valves, Strainers, Full Test/ Drain Line, Double 

Inlet  /  Outlet,  Release Monitoring  Devices  (High  Pressure  Switch), 

Release Alarm Device (Hydraulic), Pressure Gages on Upstream and 

Downstream  of  Deluge  Valve,  Pneumatic  Line  including  Air 

Regulator  with  by‐pass  Line,  Air  Back‐Up  Reservoir,  Check  Valves, 

Isolating Valves,  Pressure  Safety Valve  (PSV),  Pressure  Switch  (Low 

and Low‐Low), Junction Box, Weather Proof Cabinet and Lights AND 

Heating Sys for cold‐weather places.

Material of Construction of Deluge Valve:Main Valve Body & Cover:

• Ductile Iron ASTM A‐536* UL, ULC

• Cast Steel ASTM A216‐WCB* UL, ULC

• Naval Bronze ASTM B‐61 UL, ULC

• Nickel Aluminum Bronze ASTM B148 UL, ULC

• Super Duplex Stainless Steel UL, ULC

• Stainless Steel ASTM A743‐CF‐8M UL, ULC

Main Valve Internal Trim:

• Bronze ASTM B61

• Monel QQ‐N‐281 Class B

Diaphragm and Disc:

• Buna‐N® synthetic rubber

Material of Construction of Deluge Skid:

Depends  on  location  of  plant,  Seawater    and  Fresh  Water  are 

demanded  for  fire  fighting.  Skid  Piping  should  be  suitable  to 

withstand  against    highly  corrosive water  .  Cu‐Ni  Piping  and  Ni‐Al 

Bronze  Deluge  Valve  are  selected  for  Seawater  demanded  fire 

water. As well as Skid and its cabinet is coated with suitable painting 

to  withstand  against  highly  Saliferous and  corrosive  environment 

(Marine Environment )

Hazardous Area:

On Oil  and Gas Projects, all  Instrument  (  Solenoid Valves, Pressure 

Switches,  Junction  Boxes,  Control  Panels  and  lightings)  and 

considered suitable for Classified Hazardous Area, 

• Zone1, IIB, T3, IP 65, 

• ZONE 2, EEXD IIB T3

• ATEX EEx dm IIC T4, IP65

CERTIFICATES:  

Page 2: DELUGE VALVE AND SKID - PEDINCOpedinco.ir/wp-content/uploads/2017/08/CLA-VAL.pdfA Deluge System can be activated by the following: 1. Manually (Push Buttons on Control Panel or Local
Page 3: DELUGE VALVE AND SKID - PEDINCOpedinco.ir/wp-content/uploads/2017/08/CLA-VAL.pdfA Deluge System can be activated by the following: 1. Manually (Push Buttons on Control Panel or Local
Page 4: DELUGE VALVE AND SKID - PEDINCOpedinco.ir/wp-content/uploads/2017/08/CLA-VAL.pdfA Deluge System can be activated by the following: 1. Manually (Push Buttons on Control Panel or Local

CLA-VAL Projects and References Fire Protection / Partial List

CLA-VAL Europe www.cla-val.ch [email protected] 1 - CVREFFPDE.doc - 09/08

Platforms

Norway / Statfjord-field

Statfjord C platfrom Fire protection pressure relief valves: Model 2050B-4KG-1

Norway / Valhall oil field

BP Valhall Redevelopment Fire protection pressure relief valves: Model 50B-4KG-1 size 10" in Super Austenitic Stainless UNS S32760

Russia / Sakhalin

Sakhalin Molikpaq platform Deluge valves: Model series 134 size 6" in Ni-Al-Brz (ATSM B-148) Pressure relief valves: Model series 50 size 4" and 6" in Monel 400

North Sea

GSF Artic III Pressure reducing valves

Qatar

PS-4 platform Fire pump protection valves: Model series 50 size 10" in Super Austenitic Stainless UNS S31254 Air release and vacuum Breaker: Model 33-A size 4'' in Super Duplex Stainless Steel UNS J93404

Behzadi
Highlight
Page 5: DELUGE VALVE AND SKID - PEDINCOpedinco.ir/wp-content/uploads/2017/08/CLA-VAL.pdfA Deluge System can be activated by the following: 1. Manually (Push Buttons on Control Panel or Local

CLA-VAL Projects and References Fire Protection / Partial List

CLA-VAL Europe www.cla-val.ch [email protected] 2 - CVREFFPDE.doc - 09/08

Libya

AGIP Gas Libyan Branch - Sabratha Platform Project HYUNDAI HEAVY INDUSTRIES Co Angle pressure relief valves: Model series 50 size 12" in Ni-Al-Brz (ATSM B-148) Air release and vacuum Breaker: Model 33-A size 2'' in Ni-Al-Brz (ATSM B-148)

Germany / North Sea

Platform H-7 Fire pump pressure relief valves: Model series 50-20 size 6'' in cast steel

Norway / North Sea

EKOFISK II complex Fire pump pressure relief valves: Model series 50-20 size 6'' in cast steel

Sea Launch

Sea Launch Platform Pressure relief valves Deluge valves

Behzadi
Highlight
Page 6: DELUGE VALVE AND SKID - PEDINCOpedinco.ir/wp-content/uploads/2017/08/CLA-VAL.pdfA Deluge System can be activated by the following: 1. Manually (Push Buttons on Control Panel or Local

CLA-VAL Projects and References Fire Protection / Partial List

CLA-VAL Europe www.cla-val.ch [email protected] 3 - CVREFFPDE.doc - 09/08

Industry Plants

United Arab Emirates / Abu Dhabi

Borouge 2 World's Largest Ethylene Cracker (EU2) Deluge valves: Model series 134 size 3"-4”-6”-8” in Cast Steel (ATSM A216 WCB)

Turkey / Izmit

Gasoline Specification Improvement Project (GSIP) at the Izmit Refinery Deluge valves: Model series 134 size 3"-4”-6”-8”-10” in Ductile Iron and Stainless Steel

UAE /Jebel Ali

EMOIL PETROLEUM PRODUCTS STORAGE AND DISTRIBUTION TERMINAL AT JAFZ; JEBEL ALI Deluge valves: Model series 134 size 2", 3", 4", 6", 8"and 10" in Ni-Al-Brz (ATSM B-148)

Portugal / Sines

Steam Cracker Capacity Creep project REPSOL POLIMEROS, LDA Deluge valves: Model series 834 size 3”, 4” and 6" in cast steel

China / Guangdong

Guangdong liquefied natural gas (LNG) terminal Pump pressure relief valves: Model series 50 size 6" in Ni-Al-Brz (ATSM B-148) Air release and vacuum Breaker: Model 33-A size 2'' in Ni-Al-Brz (ATSM B-148) Model 33-A size 4'' in Ni-Al-Brz (ATSM B-148)

Behzadi
Highlight
Page 7: DELUGE VALVE AND SKID - PEDINCOpedinco.ir/wp-content/uploads/2017/08/CLA-VAL.pdfA Deluge System can be activated by the following: 1. Manually (Push Buttons on Control Panel or Local

CLA-VAL Projects and References Fire Protection / Partial List

CLA-VAL Europe www.cla-val.ch [email protected] 4 - CVREFFPDE.doc - 09/08

Congo / Moho-Bilondo field

Deep offshore Moho-Bilondo field Air release and vacuum breaker valves Pressure reducing valves Fire pump pressure relief valves

Nigeria

AKPO Field development project Fire water and cooling water system High capacity air release and vacuum breaker valve with pressure relief function: sizes 3”, 4” ,6” and 8” in Ni-Al-Brz (ATSM B-148)

Nigeria

Yoho Development Project EPC2 NIGERIAN NATIONAL PETROLEUM CORPORATION (NNPC) Mobil Producing Nigeria Limited (MPN) Deluge valves: Model series 134 size 6" & 8" in Ni-Al-Brz (ATSM B-148)

Nigeria

Ehra Project EPC1 Air release and vacuum Breaker: Model 33-A size 3'' & 4" in Monel and size 10” Air release and vacuum Breaker: Model 33-A size 3'' & 4" in cast steel

Belgium / Antwerp

ANTWERP GAS TERMINAL Deluge valves: size 4"

Behzadi
Highlight
Page 8: DELUGE VALVE AND SKID - PEDINCOpedinco.ir/wp-content/uploads/2017/08/CLA-VAL.pdfA Deluge System can be activated by the following: 1. Manually (Push Buttons on Control Panel or Local

CLA-VAL Projects and References Fire Protection / Partial List

CLA-VAL Europe www.cla-val.ch [email protected] 5 - CVREFFPDE.doc - 09/08

France / Toulouse

Assembly hall Airbus A380 Fire protection pump relief valves Angle fire pump pressure relief valves: Model series 50 size DN 400 / PN 16

France / Porcheville

2400 MW thermic power plant AFFF foam system fire protection Pressure differential valves: Model series 250 size DN 50 / PN 16

France / Fos-Cavaou

Terminal Méthanier de Fos-Cavaou Air release and vacuum breaker valves: size 8”

Sub Structures

Sweden / Stockholm

Hallandsås Tunnel Project Pressure reducing valves: Model series 90 size 3"

Switzerland / Bassecourt

Fire protection system for the largest Swiss electrical transformer. Fire protection pressure reducing valves: Model series 90 size DN 200 / PN 16 Deluge control valves: Model series 134 size DN 200 / PN 16

Behzadi
Highlight
Page 9: DELUGE VALVE AND SKID - PEDINCOpedinco.ir/wp-content/uploads/2017/08/CLA-VAL.pdfA Deluge System can be activated by the following: 1. Manually (Push Buttons on Control Panel or Local

CLA-VAL Projects and References Fire Protection / Partial List

CLA-VAL Europe www.cla-val.ch [email protected] 6 - CVREFFPDE.doc - 09/08

High Rise Buildings / Hotels

United Arab Emirates / Dubai

Burj Dubai Skyscraper - The World's Tallest SS 316 Electro-polished stainless steel pressure reducing valves sizes DN 80; DN 100; DN 150 equipped with the unique LFS internal Low Flow Feature. SS 316 Electro-polished stainless steel 55F pressure relief valves.

Egypt /Alexandria

FOUR SEASONS HOTEL SAN STEFANO Fire protection pressure reducing valves: Model series 90-21 Fire pump pressure relief valves: Model series 50B-4G-1

United Arab Emirates / Abu Dhabi

Emirates Palace Pressure reducing valves with the unique LFS internal Low Flow System On/Off level control valves UL/FM fire protection valves

Qatar / Doha

Pearl Qatar Fire protection pressure reducing valves: Model series 90-21 Fire pump pressure relief valves: Model series 50B-4G-1

Germany / Frankfurt

Frankfurter Main Tower Fire protection pressure reducing valves: Model series 90 size DN 100 / PN 25

Page 10: DELUGE VALVE AND SKID - PEDINCOpedinco.ir/wp-content/uploads/2017/08/CLA-VAL.pdfA Deluge System can be activated by the following: 1. Manually (Push Buttons on Control Panel or Local

CLA-VAL Projects and References Fire Protection / Partial List

CLA-VAL Europe www.cla-val.ch [email protected] 7 - CVREFFPDE.doc - 09/08

Qatar / Doha

Fire protection pressure reducing valves: Model series 90-21 Fire pump pressure relief valves: Model series 50B-4G-1

Qipco Twin Towers

Al Noor Tower

2B+G+21 Tower

M Tower

Al-Reem Tower

Mergab Twin Towers

Qipco Tower

Dolphin Tower

La Cigal Hotel

West Bay Complex

Mercedes Showroom

Al-Faisal Tower (ASHGHAL)

West Bay Complex Four Seasons Hotel

City Center expansion Phase II & III

Luxury Hotel & Furnished Apartment