Dell - Dell_EMC CX4 -240Series Storage Arrays - Management Module
description
Transcript of Dell - Dell_EMC CX4 -240Series Storage Arrays - Management Module
-
10/7/13 Dell - Dell|EMC CX4 Series Storage Arrays - Management Module
https://dtt.dell.com/ifr/EMC/CX4_Series_Arrays/CX4-240_man_mod.asp 1/3
Dell Training Tool | Dell|EMC CX4 Series StorageArrays
Previous | Next
Management Module
Each CX4 storage array has two management modules, one for SPA and one for SPB. Each module has SPS,management LAN and peer service LAN connectors.
The pictures below shows the management module for the CX4 storage arrays that use the 2U enclosure chassis (theCX4-120, CX4-240 and CX4-480 arrays):
Fig: Management Module for CX4-120, CX4-240 and CX4-480 Storage Arrays
The management module for SPA is situated on the right hand side of the chassis, when viewed from the rear. Themanagement module for SPB is on the left hand side.
Fig: Management Module positions
Management Module FeaturesThe management module has the following ports & connectors:
-
10/7/13 Dell - Dell|EMC CX4 Series Storage Arrays - Management Module
https://dtt.dell.com/ifr/EMC/CX4_Series_Arrays/CX4-240_man_mod.asp 2/3
Fig: Management Module Ports & Connectors
Management Module Features
Feature Connector Type Usage
Management LAN Port RJ45 1Gb Ethernet SP management
Peer Service 1GB Ethernet LANport
RJ45 1Gb Ethernet Service port management of peer SP
Management Serial Port for SP Micro DB9RS-232 connection to a service console via null modemserial cable
Standby Power Supply (SPS)Serial Port
Micro DB9 Communication between SPS and SP
NMI buttonFor engineering useonly
Forced reboot and crash dump
SP Mangement Ports and IPv6SP management ports can now be configured with a choice of either IPv4 (the default option) or IPv6 (which must beselected manually). The management port Supports IPv6 for in-bound traffic. Out-bound IPv6 support is forPing/Traceroute only. There is no IPv6 tunneling support.
Peer Service LAN PortWhen connecting to an SP using the peer service LAN port, you must be connected to the management module thatcontrols the opposite (partner or peer) SP. Hence, if you wish to connect to SPA, you must physically connect to the peerservice LAN port on the managment module for SPB. A standard Ethernet cable is used to connect to the peer serviceLAN port (cross-over cables are not require). You must use the IP address for the peer SP. The peer service LAN portprovides full GUI and CLI access to the storage array and can manage both SPs.
The IP address settings for the peer service LAN ports are as follows:
-
10/7/13 Dell - Dell|EMC CX4 Series Storage Arrays - Management Module
https://dtt.dell.com/ifr/EMC/CX4_Series_Arrays/CX4-240_man_mod.asp 3/3
Peer Service LAN port Settings
SP IP Address Subnet Mask
SPA 128.221.1.250 255.255.255.248
SPB 128.221.1.251 255.255.255.248
NOTE: Domain security applies when accessing a storage array through a Service LAN port. Log on credential for thearray are required.
Status LEDsThe tables below gives details of the rear LEDs for the CX4 SPE 2U chassis:
Management Module LED Information
LED LED condition Condition/status
Management module status LED is on module handle
Solid green Management module has power
Off Power is Not being supplied to module
Amber Module is faulted
Management/peer service LAN link LEDSolid green Good Ethernet link
off No link (bad cable or connector, configuration mismatch)
Management/peer service LAN activity LED
Blinking amber Brief bursts of data detected on port
Solid amber Streams of data detected on port
Off No data detected on port
Previous
Next
Copyright 1999-2008 Dell Inc. For Dell Employees and Dell Service Providers only.
inside.us.dell.com | Privacy Policy | About Dell | Contact Us | About Us Top