Deicing Control Facilities Improvements-2016

Project No. I-16-023

Indianapolis Airport Authority

Submittal Review Sheet

Attached is the submittal for specification section 42 2139 Submersible Liquid Pumps for the Deicing

Control Facilities Improvements – 2016 I-16-023 project for your review and approval. Thieneman

Construction has reviewed the submittal information and added the following notes for your review,

approval, and consideration

Items for Engineer:

1. KSB Submersible Sewage Pump

Items for Supplier: 1. Supply materials as requested by TCI in conformance with the project schedule.

If you have any questions on this submittal information, please contact Lori Kelleher at 317-763-1634. Thieneman

Construction requests your review, approval, and return of one (1) copy of the approved submittals

Project Name: Deicing Control Facilities Improvements-2016

Contractor: Thieneman Construction, Inc.

Subcontractor / Supplier: Straeffer Pump and Supply

Submittal Number: 000009

Submittal Specification Section: 42 2139 Submersible Liquid End Pumps Item

1.4.A.2 Product Data and

Item 1.4.A.3 Shop Drawings

Item Description: Submersible Liquid Pumps

Quantity of Submittals: 1 – Electronic

Comments: See Above

Quantity of Approved Submittals to be Returned: 1 – Electronic

Signature:

CONTRACTOR’S CERTIFICATION Submittal material has been reviewed for compliance with specifications and drawings. Required field measurements have been verified. The work shown on this submittal has been coordinated with other submittals affected by this work. All data has been checked by the Contractor and any variations from the specifications or drawings have been noted. The work described on the submittal material is recommended by the Contractor, and the guarantee in the specifications will apply:

Contractor: Thieneman Construction

Approved: Lori Kelleher

Date: 10/12/2016

STRAEFFER PUMP & SUPPLY, INC.

Since 1967

8055 State Road 62 W

P.O. Box 99

Chandler, IN 47610

800.837.7867

www.straefferpump.com

This page intentionally blank

1

GENERAL COMMENTS & NOTES FOR DEICING CONTROL FACILITIES SUBMERSIBLE LIQUID PUMP IMPROVEMENTS INDIANAPOLIS, INDIANA STRAEFFER JOB #16-098W 1. We propose to furnish one (1), Model KRT K 250-401/A806UNG-K, explosion proof, 90

HP, solids handling pumps as manufactured by KSB. KSB has been actively manufacturing equipment for over 140 years. Certified performance curve will be provided for the pump.

2. The pump will be provided with a K type impeller, trimmed to the duty point. The pump

will be furnished with: cooling jacket, double mechanical seals composed of 2 separate lapped faces (carbon vs. silicon carbide upper and silicon carbide vs. silicon carbide lower); seal leak moisture detection which, if activated, will light a pilot light in the control panel; heat sensor in the motor to stop motor if winding temperature overheats; and all exposed nuts and bolts will be stainless steel. The pumps will be furnished with bearings that have a B10 minimum bearing life per section 43 2139 - Part 2.2 - R-1. Spare parts will be supplied as specified.

3. KSB’s standard 7 year warranty is included herein. 4. The pump will be provided with 150' cord lengths. These cords cannot be spliced as it

voids warranty. Straeffer Pump and Supply will not assume the responsibility of proper cord length. Please carefully check this matter and advise if this is insufficient to reach the termination point.

5. Our company is an authorized repair station for all KSB environmental pumps. 6. We assume the supply voltage is 3/460, if not please advise. Straeffer Pump and

Supply will not be responsible for improper voltage feed to the job site. Please carefully check the voltage feed to the lift station and advise if this is incorrect.

7. To the best of our knowledge we either meet or exceed the specified equipment. However,

if questions arise, please do not hesitate to contact Mark Wahl (mwahl@straefferpump.com) for mechanical questions or Stewart May (smay@straefferpump.com) for electrical questions.....(800)837-PUMP.

PUMP SUBMITTAL REQUIREMENTS

PUMP AND MOTOR DATA PUMP #1

PUMP MODEL KRT K 250-401/A806UNG-K

MOTOR HORSE POWER 90

MOTOR RPM 1160

VOLTAGE, PHASE, & CYCLE 460/3/60

POWER CABLE LENGTH 150’

PERFORMANCE CHARACTERISTICS 3100 GPM @ 78’ TDH

IMPELLER DIAMETER 15.67”

IMPELLER TYPE multi-vane, cast iron

DISCHARGE SIZE

PUMP WEIGHT 2937 lbs.

MOISTURE SENSOR REQUIRED YES

HEAT SENSOR REQUIRED YES

UL CLASS 1 GROUP D REQUIRED YES

TYPE OF STATION Simplex

PROJECT NAME: Deicing Control Facilities Improvements

LOCATION: Indianapolis, Indiana STATION NO.

Section 43 21 39 – Pump UGSP-4

OWNER: City of Indianapolis ENGINEER:

Gresham Smith and Partners

PREPARED BY: DATE SUBMITTED:

MXW

Data sheet

Customer item no.:Communication dated: 11/08/2016 Number: 4002826961

Doc. no.: Indianapolis Airport Item no.: 100

Quantity: 1 Date: 12/08/2016

Page: 1 / 5

KRTK 250-401/A806UNG-K Version no.: 3

Operating data

Design

Driver, accessories

Requested flow rate 3100.00 US GPM

Requested developed head 78.00 ft

Pumped medium Wastewater, municipalmechanically treatedNot containing chemical andmechanical substances whichaffect the materials

Ambient air temperature 68.0 °F

Fluid temperature 68.0 °F

Fluid density 62.428000 lb/ft³

Actual flow rate 3100.00 US GPM

Actual developed head 78.00 ft

Efficiency 78.2 %

Power absorbed 77.88 HP

Pump speed of rotation 1183 rpm

Max. power on curve 85.52 HP

Shutoff head 118.18 ft

Design Single system 1 x 100 %

Fluid viscosity 0.0015 in²/s Performance test Yes

Design Close-coupled submersibleOrientation VerticalSuction flange pumpaccording to(DN1)

unmachined

Discharge flange pumpaccording to(DN2)

EN 1092-2 / DN 250 / PN 10

Shaft seal 2 mech. seals in tandemarrangement with oil reservoir

Manufacturer KSBType MGMaterial code SIC/SIC/NBR

Impeller type Multivane radial flow impeller(K)

Wear ring Casing/impeller wear ringImpeller diameter 15.67 in

Free passage size 4.13 in

Direction of rotation fromdrive

Clockwise

Temperature sensor PT100inboard

With

Color Ultramarine blue (RAL 5002)KSB-blue

Driver type Electric motorModel (make) KSBMotor const. type KSB Sub. motorNEMA code letter GFrequency 60 Hz

Rated voltage 460 V

Rated power P2 90.00 HP

Rated current 106.0 A

Starting current ratio 6.4

Insulation class H according IEC 34-1Motor enclosure IP68Cos phi at 4/4 load 0.87

Motor efficiency at 4/4 load 91.0 %

Motor service factor 1.15

Temperature sensor PTC resistorMotor winding 460 V

Number of poles 6

Starting mode Direct-on-line startingConnection mode DeltaMotor cooling method closed-circuit jacket coolingMotor cooling jacket WithMotor version UCable design Rubber hoseCable entry Sealed along entire lengthPower cable AWG 5-4Number of power cables 2

Control cable AWG 15-10Number of control cables 1

Moisture sensor With

Cable length 150.00 ft

Data sheet

Customer item no.:Communication dated: 11/08/2016 Number: 4002826961

Doc. no.: Indianapolis Airport Item no.: 100

Quantity: 1 Date: 12/08/2016

Page: 2 / 5

KRTK 250-401/A806UNG-K Version no.: 3

Materials G

Packaging

Outdoor storage at -40°C to +50°C for up to 3 months. Packetmust be covered. No corrosion protection, only transportprotection.

Nameplates

Certifications

Installation parts

Pump casing (101) Cast iron A 48 Class 35 BDischarge cover (163) Cast iron A 48 Class 35 BShaft (210) Chrome steel A 276 Type 410

TImpeller (230) Cast iron A 48 Class 35 BBearing bracket (330) Cast iron A 48 Class 35 BO-Ring (412) Nitrile rubber NBRCasing wear ring (502.1) Cast iron A 48 Class 35 B

Impeller wear ring (503) Wear resistant duplexstainless steel

Shaft protecting sleeve (524) Chrome steel A 276 Type 410T

Cooling jacket (66-2) Stainless steel A 276 Type316 Ti

Motor housing (811) Cast iron A 48 Class 35 BMotor cable (824) Chloroprene rubberScrew (900) Stainless steel A 193 B8M

Packaging category B1 Wooden or plywoodcase, cover provided withpolyproylene cellular sheet,outdoor storage up to 3months

Packaging for transport ShipIPPC Standard ISPM 15 Yes

Packaging for storage Indoor

Nameplates language International Duplicate nameplate With

Hydraulic performance testAcceptance standard Hydraulic Inst. AQuantity meas. points Q-H 7Certificate Inspection cert. 3.1 to EN

10204

Test participation Non-witnessedQuantity, non-witnessed 1Quantity, witnessed 0

Scope of supply Pump without installationparts

Performance curve

Customer item no.:Communication dated: 11/08/2016 Number: 4002826961

Doc. no.: Indianapolis Airport Item no.:100

Quantity: 1 Date: 12/08/2016

Page: 3 / 5

KRTK 250-401/A806UNG-K Version no.: 3

0 1000 2000 3000 4000 5000 6000[US GPM]

0

50

100

[ft]

Qmin

To

tal

de

ve

lop

ed

he

ad

0 1000 2000 3000 4000 5000 6000[US GPM]

5

35

20

[ft]

NP

SH

req

.

0 1000 2000 3000 4000 5000 6000[US GPM]

0

50

[%] Eff

icie

nc

y

0 1000 2000 3000 4000 5000 6000[US GPM]

60

80

[HP]

Po

wer

Inp

ut

Flow

Curve data

Speed of rotation 1183 rpm

Fluid density 62.428000 lb/ft³

Viscosity 0.0015 in²/s

Flow rate 3100.00 US GPM

Requested flow rate 3100.00 US GPM

Total developed head 78.00 ft

Requested developed head 78.00 ft

Efficiency 78.2 %

Power absorbed 77.88 HP

NPSH req. 3% 13.58 ft

Curve number K42586sEffective impeller diameter 15.67 in

Acceptance standard Hydraulic Inst. A

Installation plan

Customer item no.:Communication dated: 11/08/2016 Number: 4002826961

Doc. no.: Indianapolis Airport Item no.:100

Quantity: 1 Date: 12/08/2016

Page: 4 / 5

KRTK 250-401/A806UNG-K Version no.: 3

15.75

6.69

DN1

min

23.62

1)

Minimum water level t1

ø0.98

62.01

11.02

9.84

3.94

min

1)

71.06

15.75

DN3

27.56

79.92

20.87

8.86

5.31

16.54

ø 3.5

5.91

28.94

51.18

35.43min

0.71ø

7.28

3.94

16.73

38.98

27.17

Access opening

54.13

45.87

(Lifting bail optional)

Drawing is not to scale Dimensions in in

Installation plan

Customer item no.:Communication dated: 11/08/2016 Number: 4002826961

Doc. no.: Indianapolis Airport Item no.:100

Quantity: 1 Date: 12/08/2016

Page: 5 / 5

KRTK 250-401/A806UNG-K Version no.: 3

Motor Connections

Weight net

Connect pipes without stress or strain!Dimensional tolerances for shaft axis height: DIN 747Dimensions without tolerances, middle tolerances to: ISO 2768-mConnection dimensions for pumps: EN735Dimensions without tolerances - welded parts: ISO 13920-BDimensions without tolerances - gray cast iron parts: ISO 8062-CT9

For auxiliary connections seeseparate drawing.

Motor manufacturer KSBMotor size A80NMotor power 90.00 HPNumber of poles 6Speed of rotation 1181 rpm

Suction flange pumpaccording to(DN1)

unmachined

Discharge flange pumpaccording to(DN2)

EN 1092-2 / DN 250 / PN10

Pump, Motor, Cable 2937 lbmTotal 2937 lbm

0

20

40

60

80

100

120

140

160

200

P2[hp]

0

20

40

60

80

100

120

140

160

200

I[A]

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

1.0

etacos

0.0 20.0 40.0 60.0 80.0

P1 [kW]

1200

1190

1180

1170

n [rpm]

eta

P2

cos

I

Motor dataAmarex KRT - Installation types: K/D

Motor type : : A806UNGMaterial version : G [cast iron] also for motors -G1,-G2,-GH,-H

Nominal voltage : 460 [V]Frequency : 60 [Hz]Rated power : 90.0 [hp]Service factor : 1.15Rated current : 106 [A]Nominal Speed : 1181 [rpm]NEMA code letter : G Starting/full load current : 6.4 Max. water temperature : 104 [°F]Max. air temperature at the cable : 104 [°F]

Maximum 10 starts per hour starting mode: direct

Cable norm/ Cable selection according to: NEC

2 Cables AWG 5-4 [4G16] Ø 0.89-0.94 in1 Control cable AWG 15-10 [10G1.5] Ø 0.63-0.67 in

Descriptions : P1 [kW]........ electric power P2 [hp]........ mechanical power eta [%]........ Efficiency cos phi........ Power factor I [A].......... Current n [rpm]........ Speed

Load 4/4 3/4 2/4 1/4

n [rpm] P1 [kW] P2 [hp] eta [%] cos phi I [A] 1181 73.8 90.0 91.0 0.87 106 1186 55.2 67.5 91.2 0.83 83 1191 37.3 45.0 90.0 0.73 64 1195 20.0 22.5 83.8 0.52 48

Tolerances of the electrical parameters according to IEC 60034-1.

User: habefradate: 2016-08-12© 2000-2003 by KSB AG / Author: Dobbertin, Frank

Submersible Motor Pumps:KRT 40 - 700

Pumps n Valves n Service

02 Features

Three (3) 161 hp Dry-Pit Pumps with cooling jacket

KRT Submersible Motor Pumps for Versatile Applications

Advantages and technical features:

• economical installation

• wet installation submersible motor pumps operate submerged in

the pump sump

• low building costs, eliminating intermediate shaft, drainage

pump and superstructure

• pump stations below ground do not spoil the landscape, traffic

areas remain unchanged when sumps are located under roads

• the compact pump/motor sets require less space and are easier

to install

• with the double pump guides the pump can be installed at any

installation depth and withdrawn without difficulties

• no need to enter the pump sump to carry out inspection and

maintenance work

• smaller inspection opening on duplex pump stations

• small pump sump due to high permissible switching frequency

• stationary and portable applications possible, see types of

installations

• permanent dry well installation possible where the pump is

exposed to the danger of occasional flooding

• minimum assembly and maintenance work

• no coupling to be aligned since KRT pump and motor have a

common shaft

• no sealing or flushing water required or leakage outlet

• motor cooled by the medium

• high operation safety (dry running possible)

• quiet operation

KRT submersible motor pumps are highly efficient in

the handling of:

- raw sewage containing solid and long fibrous mixtures

- contaminated liquids with a high gas and air content

- liquids containing sludge and solid substances

- floating sludge and debris such as vegetable wastes,

wood chips and similar waste (KRT as a vacuum

suction pump on a pontoon)

- dirty water and storm water

- raw, digested and activated sludge

- flume and wash water

- pulp

- slaughter house wastes

- water/product suspensions

- sand/cement/water mixtures

- plastic granules in liquid

- textile effluent

- industrial effluent and wash water as well as media in

production plants, e.g. flume water, scale wastes,

cutting oil and other media containing abrasive

components.

- chemical and waste disposal effluent with pH-values

2 to 12

- effluent containing acid

- seawater and brackish water as well as other media

with chlorine.

Type of construction:

KRT submersible motor pumps are submerged, single

stage close-coupled pump sets. Depending on the liquid

to be pumped and the size of the pump different impel-

ler shapes are used:

K - Closed non-clogging 2 or 3 vane impeller

E - Single vane impeller

F - Vortex impeller

S - Grinding impeller

D - Open single vane impeller

Fields of application:

Two (2) 148 hp Submersible Pumps with cooling jacket.

04 Features

Impeller Type Description

S - Grinder impeller for high pressure domestic sewage systems containing long fibrous admixtures

- effluents - domestic sewage

F - Vortex impeller for liquids with coarse solids and media containing air and gas

- raw sewage - raw and digested sludge

E - Single vane impeller for media with solid and long fibrous materials

- raw sewage - raw sludge - recirculation and heating sludge

K - Closed non-clogging 2 or 3 vane impel-ler for contaminated solids-laden liquids

- raw sewage - effluent - activated sludge

D - Open single vane impeller for handling fibrous solids and heavy sludge (up to 13% solids by weight)

- raw sewage - raw and digested sludge - activated sludge - recirculation and heating sludge

The right impeller design for cost effective and reliable operation

Since no one type of impeller is equally suitable for all applica-

tions, KSB offers the KRT series of submersible motor pump with

various types of impellers according to specific requirements. Our

range of vortex, single vane and non-clogging impellers allows the

best impeller to be selected for the product with due consideration

of operating parameters such as flow rate, head, efficiency, solid

size, wear behavior and gas content.

Flexible installations

Stationary guide cableinstallation

Stationary guide railinstallation

Portableinstallation

Dryinstallation

Stationary guide cable or guide rail installation - for installation in the pump sump with suspension device ensuring automatic pressure-tight coupling of the pump.

Portable installation - with base stand and flange connection for pipework or hose connection (e.g. with rigid coupling).

Dry installation - for installation in a separate dry well.

05

The Pump That Keeps Cool

1 - Cable Entry - absolutely water tight. Even in the event of damage to the cable sheath and core insulation there is no possibility of moisture entering the motor chamber along the strands due to capillary action.

2 - Thermal Motor Protection - extensive sensor technology for permanent monitoring to ensure trouble-free operation.

3 - High Efficiency Motor - all motors FM approved for Class I, Division 1 Group C & D hazardous locations.

4 - OPTIONAL Closed-loop Cooling System - optimal cooling in all operating conditions with no external cooling required, perfect for dry-well installations .

5 - Non-proprietary silicon carbide faced mechanical seals mounted in tandem in collant liquid bath.

6 - Major Casting of ASTM A 48 Class 35 B Cast iron, Duplex Stainless steel and wear resistant Chromium White Iron.

7 - Heat exchanger and separate coolant circulating impeller for optional cooling jacket.

8 - Enclosed 1, 2 and 3 vane or recessed impellers available to allow a hydraulic selection ideally suited for a particular application.

9 - Wear rings in hard metal to insure continued high efficiences and long impeller life.

10 - Pump and motor shafts of stainless steel or Gr 1045 carbon steel protected and isolated by stainless steel shaft sleeves (only for carbon steel shafts).

11 - Temperature monitoring standard for lower bearing, optional for upper bearing.

12 - Float sensor in separate leakage collection chamber. Prevents leakage from reaching motor or lower bearing.

* Motors larger than ~80 hp:• 1

• 2

• 3

• 4

• 6 • 8 • 9

10 •

11 •

12 • • 5

• 7

* For certain models, 30, 40, 50, 56, and 74 HP motors with cooling jacket are also available.

06 Installations and Technical Data

Three (3) 12“ discharge, 161 hp closed-loop cooling dry-pit pumps with stainless steel Jacket in existing pumping station.

Dry Well Installations

Two (2) large 24“ discharge, 148 hp Submersible Pumps with stainless steel cooling jacket on KSB guide rail system for an effluent waste water treatment pumping station.

Wet Well Installations

Three (3) 10“ discharge, 194 hp closed-loop cooling dry-pit pumps with stainless steel Jacket in existing pumping station.

Two (2) large 24“ discharge, 251 hp Submersible Pumps and one (1) 12“ discharge, 80 hp on KSB guide cable system for a stormwater station.

07

Technical Data

Operating Data

Pump Size - DN 2” - 30”

Capacity - Q (gpm) up to 45,000

Head - H (ft) up to 330

Liquid Temperature - t (°F) up to 140

Motor Rating - P (hp) up to 1,140

Material Options Cast Iron A 48 Class 35 B

Wear Resistant Chromium White IronA 532 II C 15% CrMo-Hc

Duplex Stainless SteelA 743 CD 4 MCU

Part Designation G G1 G2 GH H C1 C2

Pump Casing A 48 Class 35 B A532 II C 15% CrMo-Hc A 890 CD 4 MCU

Intermediate Casing

A 48 Class 35 B A 532 II C 15% CrMo-Hc A 890 CD 4 MCU

Shaft A 276 Type 420;A 576 Gr. 1045 w/shaft protection sleeve

A 182F51/A276 Type 420/ A576 Gr. 1045

Impeller A 48 class 35 B

A 743 CD 4 MCU

A 532 II C 15% CrMo-Hc A 890 CD 4 MCU

Motor Casing A 48 Class 35 B A 890 CD 4 MCU

Discharge Elbow A 48 Class 35 B A 532 II C 15% CrMo-Hc A 890 CD 4 MCU

Power/Control Cable

Neoprene

Revised 10/2003

Supersedes all previously published warranties

Submersible Pumps KRT / KRTB (except grinder pumps) Warranty for Permanent Municipal Installations

Seven Year Or 12,500 Hour KRT Pump Warranty And

Ten Year Guide Cable Warranty For Permanent Municipal Installations

KSB, Inc. warrants to the Original End Purchaser that its

Pump(s) will be free from defects in workmanship and materials

covering parts and labor for a period of seven (7) years or twelve

thousand five hundred (12,500) hours of operation, and that its

Guide Cable will be free from defects in workmanship and

materials covering parts and labor for a period of ten (10) years

of operation when pumping abrasive-free, non-corrosive liquids

used in Permanent Municipal Installations. This warranty

commences on the date KSB, Inc ships the pump(s).

KSB Pump(s) are warranted for seven (7) years for use in

Sewage Collection systems or intermittent duty cycle pumping.

KSB Pump(s) are warranted for 12,500 hours of operation for

use in Sewage Treatment Processing or for continuous duty

cycle pumping. For the purpose of this clause, continuous duty

cycle is defined as twelve (12) hours per day average operation

time, or greater.

In the event that defects in workmanship or materials appear

during the term of the warranty, the Purchaser shall deliver

written claim of Warranty to the Company within ninety (90)

days of discovery. The obligation of KSB, Inc. under the

warranty shall be limited to replacement of defective part(s)

and/or labor whichever KSB, Inc., in its sole discretion, chooses

to elect. The Original End Purchaser shall be entitled to this

warranty provided that the terms of payment have been

complied with and the pump(s) with cable(s) attached or faulty

part(s) thereof have been returned freight prepaid to KSB, Inc.

or to an authorized KSB Service Facility and the defect has

been acknowledged in writing by KSB, Inc. to be caused by

faulty workmanship or defective material. Normal wear and tear

is specifically excluded from warranty coverage.

This warranty does not apply to KSB Grinder Pumps. The

warranty shall be void if the pump(s) or its part(s) have not been

used and maintained in accordance with the printed

instructions of KSB, Inc., or have been damaged wholly or in

part by misuse, accident, neglect, faulty electrical system, or

any other cause beyond the control of KSB, Inc.

Unless otherwise specified by KSB, Inc., the warranty period

shall be computed from the original shipping date to the date

the pump(s) and/or part(s) are returned to KSB, Inc. or, if repairs

are made on site, the warranty period shall be computed to the

date notice of defects is received by KSB, Inc.

Pump(s) or part(s) repaired or replaced will be returned at the

cost of the Original End Purchaser. Repairs or replacement

parts are warranted free from defects in workmanship and

materials for the longer of the un-expired term of this warranty

or ninety (90) days from the date KSB, Inc. ships such repaired

or replaced items, and all other terms and conditions of this

warranty shall apply. The extent of the Original End

Purchaser’s share in the repair or replacement cost detailed

below shall be paid prior to shipment by KSB, Inc.

Electrical system schematics (including bills of material) may be

required to support any warranty claims at the request of KSB,

Inc. This documentation will normally be required in the case

of pumps or 20 horsepower and larger.

KSB, Inc. will bear the cost for such repair or replacement as

follows:

Item

Categories

I

II

III

IV

Months after

Shipment

0-18

19-39

40-59

60 - 84

Hours of Operation

0-2,999

3,000-6,499

6,,500 – 9,999

10,000 – 12,500

A. Pumps

KSB Share of Cost

100%

50%

25%

10%

Months after

Shipment

0-120

-

-

-

B. Guide Cables

KSB Share of Cost

100%

-

-

-

KSB, INC. WILL NOT BE RESPONSIBLE FOR TRAVEL EXPENSES, RENTED EQUIPMENT, OUTSIDE CONTRACTORS’ FEES,

UNAUTHORIZED REPAIR, SHOP EXPENSES OR FOR PUMPS PURCHASED OR USED WITHOUT KSB SUPPLIED POWER CABLE(S).

THE WARRANTIES MADE HEREIN BY KSB, INC. ARE IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED.

KSB, INC. DISCLAIMS ANY AND ALL WARRANTIES FOR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. KSB, INC.

ASSUMES NO LIABILITY FOR LOSS OF USE, LOSS OF PROFIT, OR ANY DIRECT, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES OF ANY KIND.

No sales agent or sales representative or any other person is authorized to modify, extend, or enlarge this Warranty. Any modification,

extension, or enlargement of this Warranty shall not bind KSB, Inc.