Decorative Wall Panels Website. …...DECORATIVE WALL PANEL 159 GLUE Multi-tool RUBBER MALLET HAMMER...
2
1-inch/2-inch SLAT DECORATIVE BUILDING PRODUCTS DECORATIVE WALL PANEL 159 GLUE Multi-tool RUBBER MALLET HAMMER OPTION 1 For direct fixing system make sure surface substrate is true and level. OPTION 2 (Recommended) STEP 1 Using packers on surface before placing wall panels. To avoid existing skirtings, non level surfaces, corner not square issue, and such. Install packer at a maximum of 600mm centres (Recommended at 400mm centres). Identify solid fixing points in the existing wall or framing. Level for packer, Then using nail gun and glue to secure each. INSTALLING WALL PANELS STEP 2 Cut wall panel into length. Then layout wall panel from the male side, allow the next panel to joint from the female side. Using level to make sure the first panel is level. Identify solid fixing points in the existing wall or framing. Then, using nail gun to secure the first panel. LEVEL TOP VIEW NAIL GUN(MAX. 30MM NAILS) OPTIONAL - PACKERS (THICKNESS 9MM to 20MM) v1.3 L-shape corner trim Decorative Wall Panels Installation Guide Website. Phone. Email. www.dbp.nz 09 3200 633 [email protected] YOU WILL NEED BASIC & STEPS OPTION 1 Description MALE SIDE JOINT FROM MALE SIDE TO FEMALE SIDE EXISTING WALL / FRAMING EXISTING WALL / FRAMING FEMALE SIDE OPTION 2 PACKER 400MM TO 600MM STEPS 1 *Tips: Doing spots at about 5MM thick. SAVE A LOT OF SILICONE. *Tips: Using slat and L trim to cover nails. PACKER First panel only Nail gun here before stack. STEPS 2 1. Level the first panel 2. Secure with nail gun Secure with nail gun at female side before stacking next panel. Hammer the newly added wall panel to make sure it is fully inserted. 3. Hammer the newly added wall panel to make sure it is fully inserted.
Transcript of Decorative Wall Panels Website. …...DECORATIVE WALL PANEL 159 GLUE Multi-tool RUBBER MALLET HAMMER...
1-inch/2-inch SLAT
DECORATIVE BUILDING PRODUCTS
DECORATIVE WALL PANEL 159 GLUE
Multi-tool
RUBBER MALLET HAMMER
OPTION 1For direct fixing system make sure surfacesubstrate is true and level.
OPTION 2 (Recommended)STEP 1Using packers on surface before placingwall panels. To avoid existing skirtings, non level surfaces, corner not square issue,and such.
Install packer at a maximum of 600mmcentres (Recommended at 400mm centres).
Identify solid fixing points in the existing wall or framing. Level for packer, Thenusing nail gun and glue to secure each.
INSTALLING WALL PANELSSTEP 2Cut wall panel into length. Then layout wall panel from the male side, allow the next panel to joint from the female side.
Using level to make sure the first panel is level. Identify solid fixing points in the existing wall or framing. Then, using nailgun to secure the first panel.
LEVEL
TOP VIEW
NAIL GUN(MAX. 30MM NAILS)
OPTIONAL - PACKERS(THICKNESS 9MM to 20MM)
v1.3
L-shape cornertrim
Decorative Wall Panels Installation Guide
Website.Phone.Email.
www.dbp.nz09 3200 [email protected]
YOU WILL NEED
BASIC & STEPS
OPTION 1D
escr
iptio
n
MALE SIDE
JOINT FROM MALE SIDE TO FEMALE SIDE
EXISTING WALL / FRAMING
EXISTING WALL / FRAMING
FEMALE SIDE
OPTION 2
PACKER
400MM TO 600MM
STEPS 1
*Tips: Doing spots at about 5MM thick. SAVE A LOT OF SILICONE.
*Tips: Using slat and L trim to cover nails.
PACKER
First panel onlyNail gun here before stack.
STEPS 2
1. Level the first panel
2. Secure with nail gun
Secure with nail gun at female side before stacking next panel. Hammer the newlyadded wall panel to make sure it is fullyinserted.
3. Hammer the newly added wall panel to make sure it is fully inserted.
SLAT SLATSLAT
SLAT
L-SHAPE TRIM
*Tips: Do not remove wall panel protection wrap before finish. Draw marks on wall panel where cutting is required.
*Tips: Using multi-tool or renovator to cutholes on our wall panel.
STEPS 3
1-inch/2-inch SLAT
DECORATIVE BUILDING PRODUCTS
DECORATIVE WALL PANEL 159 GLUE
Multi-tool
RUBBER MALLET HAMMER
STEP 3While making the wall where you needto reserve a spot for your power pointor TV cable socket. Mark the area of thecutting spot. Use multi-tool or renovatorto cut out.
Cutting panel to fit your dimensions, turnthe wall panel to face down. drawer lineand cut the wall panel.
*Tips: When you are securing the last wallpanel, nail gun the edge within the covering slat or L trim width.
STEP 4Using slat and L-shape trim to cover corners with glue.
Apply covers on all edges or only fews isoptional. For better finish, joint edges using 45 degree angle jointing.
Remove protection wrap and installpower points back to position.
STEP REVIEW
1. Cut wall panel into length2. Level and secure packers3. Level and secure first panel4. Hammer panel before stack5. Cutting holes/non cover area6. Install cover slat and L-trim7. Remove protection wrap
LEVEL
NAIL GUN(MAX. 30MM NAILS)
OPTIONAL - PACKERS(THICKNESS 9MM to 20MM)
v1.3
L-shape cornertrim
Decorative Wall Panels Installation Guide
Website.Phone.Email.
www.dbp.nz09 3200 [email protected]
YOU WILL NEED
STEPS
Des
crip
tion
STEPS 4
SLAT
