DC Power Supply System Product...

ULTRON ELECTRONICSAN ISO Certified Company

ULTRON Website: www.ultronelectronics.inO�ce: Plot No.133/1/B, Phase- II, IDA, Cherlapally, Hyderabad - 500 051

DC Power Supply System Product Speci�cation0-16V/0-6A DC Power Supply 1

Input:

Output:

Line & load regulation:

Ripple:

Indications:

Controls:

Terminations:

Protections:

Mechanical:

230v ac, +/-10%, 50hz, single phase

0-48v/0-10amps

±0.05% for variations in input and load variations

Less than 3mv RMS

LED indications for ac input CV,CC operations

4 ½ digit digital meters to read output voltage & load current.

On/O� switch at input side

Coarse and �ne voltage set potentiometer

Coarse current set potentiometers

Input through a power card

Output will be brought on to binding terminals on front panel and also with

remote sense terminals on to rear panel

Fuse protection will be provided

Outputs are protected against over loads & short circuits

Bench top model



DC Power Supply System Product Speci�cation15V/3A DC Power Supply 2

Input:

Output:

Line regulation:

Load regulation:

Ripple:

Draft in 24 Hrs:

Output Voltage Adjust:

Protection:

Indications:

Terminations:

Operating Temperature:

Power supply failure

alarm:

Parallel operation:

230V AC +/- 10%, single Phase

±15V DC, 3A

Less than 0.1% for change in input voltage from 207V to 253V

+/-0.1% for change from no load to full load and vice versa

Less than 5mv RMS

Less than 25%

±5% of rated output

Output will be protected against over loads, voltages & continuous short circuits

One LED each to indicate the availability of DC outputs

Input is given through a circular connector & output is given through a PIRI Terminal.

0 TO 55°

<0.025% per degree

Will be provided




Input:

Output Voltage:

Output current:

Line regulation:

Load regulation:

Ripple:

Protections:

Front Panel Controls:

Front Panel Indications:

Dimensions:

230V +10%, 50Hz, Single Phase

0-16V DC

0-6A Max

1) CV: <0.1% +2mV

2) CC: <0.1% +250 micro Amps

1) CV: <0.1% +2mV for full load to no-load conditio

2) CC: <0.1% +250 micro Amps for change in Output voltage from 15V to 0V

Less than 2mV RMS

1) Unit is protected against input surges

2) Unit is protected against over loads and continuous short circuits

3) Fuse protection for both input and output

1) Unit ON/OFF switch

2) Coarse Potentiometers to set the output voltage at required level is provided on

Front Panel.

3) Input and Out put fuse

4) Binding Terminal for Output

1) LED for Input and Output

2) 3½ Digit digital panel meter to read the output voltage and output load current

310mm (W) x 250mm (D) x 133mm (H)



DC Power Supply System Product Speci�cation24V/2A DC Power Supply 4

Input:

Output:

Line regulation:

Load regulation:

Ripple:

Draft in 24Hrs:

Output Voltage adjust:

Protections:

Indications:

Terminations:


Mechanical Size:

Relative Humidity:

Temperature Coe�cient:


±24V DC, 2A

Less than 0.1% for change in input voltage from 207V to 253V

±0.1% for change from no load to full load and vice versa

Less than 5mV RMS

Less than 25%

±5% of rated output

Output will be protected against over loads, voltages & continuous short circuits.

One LED each to indicate the availability of DC outputs

Input is given through a Circular connector & output is given through a PIRI Terminal

0 to 55 Degree

3U Height X Half 19” Rack width x less than 300mm depth

0 to 90% without condensation

Less than 0.025% per Degree C




Input:

Output Voltage:

Output Current:

Line regulation:

Load regulation:

Controls:

Ripple:

Protections:

Indications:

Controls:

Terminations:

Operating Environment:

Terminals:


0-30V

0-30A

+ 0.1% max Output Voltage for + 10% change in mains Input Voltage

+ 0.1% max.Output Voltage Change for No-load to full load or Vice-versa

1) Switch for Unit ON/OFF

2) Coarse & �ne controls will be provided on front panel for output Voltage &

Current settings

Less than 5mV RMS

1) Over load / Short circuit:Automatic crossover type (CV/CC)

2) Reverse Voltage:Protection against reverse voltage applied at the outpu

terminals will be provided

3) Fuse protection will be provided for both Input and Output at rear side

Two separate front panel 3½ digit digitat panel meters to monitor output voltage

and Current continuously will be provided

Input is given through a Circular connector & output is given through a PIRI Terminal.

0°C to +50°C

Banana socket(s) at front panel & Piri strip with remote sensing at rear panel



DC Power Supply System Product Speci�cation0-250V,0-5A DC Power Supply 6

Input:

Output Voltage:

Output Current:

Line regulation:

Load regulation:

Ripple:

Protections:

Indications:

Metering:

Front Panel Controls:


Terminations:

Dimensions:

230v ac ±10%, 50hz, single phase

0-250v DC (continuously variable with coarse and �ne control)

5A Max

1% for variations in input from 207v to 253v AC

1% for variations in load from no load to full load and Vice Versa

±3 % rms (maximum)

1) Unit is protected against input surges

2) Fuse protection is provided at input side of the unit

3) Output is protected against over load and continuous short circuits

LED indication for input and output

One digital meter for voltage and one digital meter for current

1) On/O� switch

2) One potentiometer for coarse control and potentiometer for �ne control to set

the output voltage

0-50°c

PIRI terminal strips are provided for both input and output

1) 19” rack mounting or bench top as required by you

2) 482mm (w) x 300mm (D) x 177mm (H)




Input:

Output Supply:

Output Current:

Line regulation:

Load regulation:

Ripple & Noise:

Stability:


Mode of Operation:

Protections:

Controls:

Indications:

Terminations:

Mechanical:

230V AC, +/-10%, 50-60Hz, Single Phase

0-20V variable

0-5A

0.1% for change in Mains Voltage

0.1% for load change from no load to full load and vice versa

Less than 1mv RMS

Total drift within 8 hrs after warm up < +/-0.2% plus 5mV

0 to +50°C

Linear Regulated with CV/CC technique for 0-20V

1) Fuse protection at AC Input

2) Output is protected against over loads and continuous short circuits.

1) ON/OFF switch at AC Input

2) Coarse and Fine potentiometes set the output voltage from 0-20V continuously

3) Coarse and Fine potentiometes set the output current from 0-5A continuously

1) LED Indication for AC input, CC and CV

2) 3 ½ Digit Voltmeter and Ammeter to read both voltage and current continuously.

1) Input is given through a power card

2) Output is brought on to binding terminals mounted onFront Panel.

Bench top model



DC Power Supply System Product Speci�cation0-15V/0-1A Dual Output DC Power Supplies 8

Input:

Output Supply:

Output Current:

Line regulation:

Load regulation:

Ripple & Noise:

Protections:

Indications:

Controls:

Terminals:


Cooling:

Mechanical:

230V, +10%, 50Hz, Single phase

0 – 15V/0-1A

0-6A Max

+ 0.01% + 2mV for input line change from 207V AC to 253V AC and vice versa

Better than + 0.01% + 2mV for a load change

Better than 1mV RMS

1) Unit is protected against input surges through Line �lter

2) All the outputs are protected against overload and continuous short circuits

3) All the outputs are fuse protected

1) One LED for input AC

2) One DC LED for each output

3) One 3½digit Digital Voltmeter and one 3½digitDigital Ammeter with a selector

switch to read both Voltage and Current of each output

1) ON/OFF switch to ON/OFF the Unit

2) AC fuse, DC fuse separately for each output

3) Coarse and Fine Potentiometers to set the output voltage from 0 volts to Max

volts foreach channel separately

4) Two separate 3 ½ digit digital panel meters to monitor output voltage & current

continuously will be provided with a 4 pole/3way RotarySwitch.

1) Input is given through 3 pin power card

2) All the outputs are terminated on Piri Terminal strip with remote sensing facility

at the rear of the unit

3) Outputs are also brought on to Front Panel on Banana Sockets

0 – 50°C

Natural air cooling/Forced air cooling

Bench top Model



DC Power Supply System Product Speci�cation0-6V/0-3A,0-12V/0-3A,0-22V/0-3A Multi Output Power Supply 9

Input:

Output Supply:

Line regulation:

Load regulation:

Ripple & Noise:

Protections:

Indications:

Controls:

Terminals:

Operating Temperature :

230V, +10%, 50Hz, Single phase

0 – 6V/0-3A, 0 – 12V/0-3A, 0 – 22.5V/0-3A continuously variable by coarse & �ne

potentiometers mounted on Front panel

Better than + 0.01% for input line change from 207V AC to 253V AC and vice versa

Better than + 0.01% for a load change from no-load to full load and vice versa.

Better than 1mV R.M.S.

1) Unit is protected against input surges through Line �lter

2) All the outputs are protected against overload sand continuous short circuits

1) One LED for input AC

2) One DC LED for each output

3) One 3½digit Digital Voltmeter and one 3½digit

1) ON/OFF switch to ON/OFF the Unit

2) AC fuse Control, DC fuse separately for each output

3) Coarse and Fine Potentiometers to set the output voltage from 0 volts to

max volts for each output

4) Coarse and Fine Potentiometers to set the output current form 0 Amps to

max value for each output separately

5) Two separate 3 ½ digit digital panel meters to monitor output voltage & current

continuously will be provided with a 4 pole/3way Rotary Switch

1) Input is given through 3 pin power card

2) All the outputs are terminated on Piri Terminal strip with remote sensing facility

at the rear of the unit

3) All the outputs are also brought on the Front Panel on Banana Sockets

0 – 50°C



DC Power Supply System Product Speci�cation5V/5A 15V/5A 0-30V/0-5A Multi Output DC Power Supply 10

Input:

Output Supply:

Line regulation:

Load regulation:

Ripple & Noise:

Stability :


Mode of operation :

Protections:

Controls:

Indication :

Termination :

Mechanical :

230V AC, ±10%, 50-60Hz, Single Phase

Dual ±5V, ±15V AND 0-30V

5A, 10A AND 0-5A

0.1% for change in Mains Voltage

0.1% for load change from no load to full load and vice versa

Less than 1mv RMS

Total drift within 8 hrs. after warm up < +/-0.2% plus 5mV

0 to +50°C

Linear Regulated with CV/CC technique for all the three outputs

1) Fuse protection at AC Input

2) Outputs are protected against over loads and continuous short circuits

1) ON/OFF switch at AC Input

2) Voltage set potentiometer for each output

3) Meter Selector Switch

1) LED Indications for AC input at all outputs

2) 3 ½ Digit Voltmeter and Ammeter with selector switch to read all outputs.

1) Input is given through a power card

2) All outputs are brought on to binding terminals on Front Panel

3) All the outputs are also brought on the Front Panel on Banana Sockets

19” Rack Mountable



DC Power Supply System Product Speci�cationArc Lamp Power Supply 11

Input:

Output Supply:

Output Voltage Stability:

Wave Form:

Output Frequency :

Stability :

Output Current:

Line Regulation:

Load Regulation

Distortion:

Protections:

Over Load Trip :

Metering :

230V/415AC+/-10%,50 to 60Hz Single phase

115/230V A.C.Single phase

±5 settable over nominal output voltage

Sine wave

400Hz ±1%

Better than ±0.5%

Upto 5 KVA

±3%

±3%

Less than 3%

Input –Fuse protection. Output-protected against over Load and short circuits

Unit will trip at 120% of the rated load.

Separated meters for output voltage and current.



Automatic Battery Chargers Product Speci�cationSingle Phase Battery Charger 12

Input:

Output:

Output current:

Regulation:

Ripple:

Mode of working:

Charging Hours

Protections:

Mode of Charging:

Timer:

Mechanical:

415V/ 230V/ 110V +10% 50 to 60Hz Single Phase/Three Phase

12V, 24V, 36V, 48V, 60V, 72V or 110V

1A to 50A

5%, 2%, 1% or 0.1% of the output voltage

5%, 1% or 0.1% of the output voltage

Float/boost/Initial/Manual/Auto Range

1 to 24 hours Presettable or Auto Setting

Over load/Short circuit Battery reverse protected & against wide input �uctuations.

Protection against over charge/over use of battery

Constant Voltage mode or Constant current mode charging depending on the

type of battery

Mechanical /Electronic Timers for 1 to 24 Hours settable

Bench Top or Rack mounting depending on the customer requirements



Automatic Battery Chargers Product Speci�cationBattery Charger 13

Input:

Output:

Max. Current:

Regulation:

Ripple:

Mode of working:

Charging hours:

Protections:

Mode of charging:

Timer:

Mechanical:

Uses:

415V/ 230V/ 10V +/-10P to 60Hz Single phase/Three phase

12, 24, 36,48,60,72 or 110V

1A to 50A

5%, 2%, 1%or0.1% of the output voltage.

5%, 1% or 0.1% of the output voltage.

Float /boost/initial/Manual/Auto range.

1 to 24 hours presettable or Auto setting.

1) Over load /short circuit Battery reverse PROTECTED and against wide input

�uctuations

2) Protection against over charge/over use of battery.

1) Constant voltage mode or constant current mode charging depending on the

type of battery.

Mechanical /Electronics timers for 1 to 24 hours set table.

Bench top or Rack mounting Depending on the customer Requirements.

1) Railways & telecommunications.

2) Electricity board sub-stations.

3) Domestic & Industrial chargers.



Automatic Battery Chargers Product Speci�cation12V/24V/10A Battery Charger 14

Input:

Output:

Output current:

Regulation:

Ripple:

Mode of operation:

Protections:

Mode of Charging:

Dimentions:

230v 50hz, single phase

12v/24v DC supply

10A Max

5%

5%

boost and �oat

1) Over load short circuit

2) Reverse protection

3) Fluctuations

4) Charge/over use

1) Constant voltage or current.

2) Current depends on battery

1) Width: 310

2) Depth: 350

3) Height: 175



Automatic Battery Chargers Product Speci�cation12V/200A Automatic Battery Charger 15

Input:

Output:

Output current:

Regulation:

Regulation:

Mode of operation:

Protections:

Mode of charging:

230v 50hz, single phase

12v dc supply

200A Max.

5%

5%

CV/CC

1) Over load

2) Short circuit

1) Constant voltage or current.

2) Current depends on battery



Automatic Battery Chargers Product Speci�cation24V/21A Dc Power Supply Cum Battery Charger 16

Input voltage variation :

Input current :

E�ciency :

Power factor:

Output voltage :

Output current :

Voltage :

Output voltage Nominal :

Boost :

Constant current :

Batteries :

Capacity :

Model :

Make :

Connectors :

AC in:

DC/battery out :

Charger out:

Indications :

100-260v ac, 50hz

4A @ 230V AC

Better than 80%

0.99%

24v DC

21amps

230V ±15%

26.5V

28v

2amps

2nos.

12V, 17AH

lc-rd1217ch

Panasonic

3pin ms circular connector



1) Ac on, Power supply on, Charger on, Battery on-charge, Load on battery

Full charge, Charger on internal battery, Charger on external battery, Battery low



Automatic Battery Chargers Product Speci�cationBattery Charger Cum Power Supply 17

Input :

Output :

Output current :

Digital display :

Ripple :

E�ciency :

Insulation resistance :

Charging :

Discharge facility :

Protection :

Indications :

220V +10% 50Hz (AC line power)

1) 40V to 75 DC Variable

2) 0 to 10V DC Variable

3) 20-70V DC Variable

1) 0 to 3 Amps

2) 0 to 7 Amps

3) 0 to 750mA Amps

4½ digit meters for measuring voltages and currents

< 1% RMS at Battery

>70% @ nominal input and out put at 100% load

> 2M ohm between the live point and the ground

The charger will be able to charge 24 cells of sealed lead acid batteries of 2V each

with constant voltage and current limit to a maximum of 3Amps.

Suitable load will be provided for discharging the battery 24 cells of 2V each

@ C/10 rate (25Ah Battery)

1) Battery Reverse Protection, Under voltage cut o�

2) Battery Over charge Protection

3) Over Load Protection and Short Circuit Protection

1) Discharge ON and Input ON

2) The charger Input/Output will be terminated on Front Panel.



Auxiliary AC Power Source Product Speci�cationFrequency Converters Frequency 18

Input:

Output Voltage:

Settability:

Wave form:

Output frequency:

O/p frequency stability:

Output power:

Load & Line regulation:

Distortion:

Controls:

Protection:

Overload trip:

Metering:

Manuals:

Warranty:

230V +/-10%, 50HZ

115V, Single Phase

±10V settable over nominal output voltage

Sine Wave

400Hz, +/-4% adjustable by front panel control.

Better than +/-0.5%

1000VA

±1%

Less than 3%

1) ON/OFF Switch at input side

2) Coarse and �ne voltage set potentiometers

3) Coarse current set potentiometers

1) Fuse protection will e provided at input

2) Output will be protected against over loads and continuous short circuits.

will be provided

Separate meters for output voltage and current.

1 set of instruction and operative manual will be given along with each unit.

1 year from the date of supply



Auxiliary AC Power Source Product Speci�cationDual Power Supply For Pure Air Generator 19

Input

Voltage:

Frequency:

Output

Voltage(Pure sine wave):

Frequency:

Current Rating:

Load Type:

Voltage:

Current Rating:

Ripple:

Protection:

Indication:

230V AC (207 – 250V AC)

50Hz (48 – 52Hz)

115V AC (98 – 124V AC)

400Hz (380-420 Hz)

6 Amps

Inductive

28V DC (18 – 30V DC)

300m Amps

3mV RMS

Short circuit protection & Over load protection

1) AC Voltage, Current

2) DC Voltage, Current



Switch Mode Power Supplies Product Speci�cationSwitching Mode Power Supply 20

Input Voltage:

Output Voltage:

Load current:

Line Regulation:

Load Regulation:

Ripple RMS:

Current limit:

E�ciency:

Protection:

Dimension:

Storage Temperature:


Humidity:

Burn in Test:

230V AC +/-10%

5V DC to 96VDC

1 Amp to 20A

1%

5%

<100mV

2 to 20Amp

>80%

Short circuit protection will be provided

Depending on Model/td>

-20 C to +85 C

0 C to 55 C

95% RH

100 Hours at full load



Switch Mode Power Supplies Product Speci�cationSMPS Battery Charger 21

Input Voltage:

Output Voltage:

Load current:

Line Regulation:

Load Regulation:

Ripple RMS:

Current limit:

E�ciency:

Protection:

Dimension:



Humidity:

Burn in Test:

-

-



Servo Voltage Stabilizers Product Speci�cationServo Controlled Voltage Stabilizers 22

Input Voltage:

Input Frequency:

Output Voltage:

Output Regulation:

E�ciency:

Correction Rate:

Servo Drive:

O/P waveform distortion

E�ect of load power factor

Protection:

Time delay for cut o�

Over load protection :

Motor protection :

Metering :

Ambient Temperature :

Indication :

SINGLE PHASE

170V 270V

47 53Hz

220V/230V/240V

1%

About 98°o

More than 35V 7sec

Synchronous Motor

Nill

Nill

Over voltage / under voltage

3 sec (Max)

By Fuse/MCB

Through fuse

Volt Meter for I/P O/P selector switch

0-45°C

1) Input on low high

2) Output on low high

THREE PHASE

340V 460V

47-53HZ

380V/400V/415V

1%

About 98°o

More than 35V 7sec

Synchronous Motor

Nill

Nill

Over voltage / under voltage single phase

3 sec (Max)

By Fuse/MCB

Through fuse


0-45°C



3) Single phase output cut o�



Servo Voltage Stabilizers Product Speci�cationUltra Servo Controlled Voltage Stabilizers 23

Input Voltage:

Input Frequency:

Output Voltage:

Output Regulation:

E�ciency:

Correction Rate:

Servo Drive:

O/P waveform distortion

E�ect of load power factor

Protection:

Time delay for cut o�

Over load protection :

Motor protection :

Metering :

Ambient Temperature :

Indication :

SINGLE PHASE

170V - 270V

47 53Hz

220V/230V/240V

1%

About 98°o

More than 35V 7sec

Synchronous Motor

Nill

Nill

Over voltage / under voltage

3 sec (Max)

By Fuse/MCB

Through fuse


0-45°C



THREE PHASE

340V 460V

47-53HZ

380V/400V/415V

1%

About 98°o

More than 35V 7sec

Synchronous Motor

Nill

Nill

Over voltage / under voltage single phase

3 sec (Max)

By Fuse/MCB

Through fuse


0-45°C



3) Single phase output cut o�



Solar Systems Product Speci�cationSolar Power Systems 24

Input Voltage:

Output Voltage:

Load current:

Line Regulation:

Load Regulation:

Ripple RMS:

Current limit:

E�ciency:

Protection:

Dimension:



Humidity:

Burn in Test:

-

-

-

-



Solar Systems Product Speci�cationSolar Charge Controllers 25

Nominal Voltage:

Max. Charging current :

Discharge protection :

Over Charge Protection :

Restart Of Charging :

Reconnection of Load :

Output load current :

Battery AH Rating :

Solar Panel :

Operating Temp. :

Self Consumption :

Protection :

Indications :

12V /24V/36V/48V DC

10A/20A/30A/ 40A/50A/75A/100A

10.5V/21.0V

14.4V/28.8V

12.5V/25V

12.5V/25V

10A Max.

100AH Max.

120Watts Max.

50°C

25ma

1) Battery Reverse Protection, Battery Over charge Protection

2) Solar Panel Reverse Protection, Over Load Protection

3) Short Circuit Protection, Battery deep discharge protection

4) Load cut o� at set time

1) Charging on Solar, Battery Low, Over Load

2) Battery Reverse, SPV Reverse

3) 16X2 LCD Display to read real time and to set the load on by o� time



Solar Systems Product Speci�cationSolar Inverters And Home UPS 26

Solar PV Panels :

800VA/1500VA/3000VA :

Zero Drop Solar

chargers/MMPT :

Voltage :

Frequency :

Phase :

Protection :

UPS voltage :

Frequency :

Waveform :

Power :

Power factor :

Battery :

DC Voltage :

Type:

Charging Time :

Protection :

Over load :

Short Circuit :

Battery low cut :

Battery reverse :

Low battery warning :

Input under voltage :

Input over voltage :

Input under voltage :

Input over voltage :

75 wp

2 Nos /4Nos/8Nos

10A, 30A, 60A available at 12V 24V and 48V

120 v to 275 v AC

47H z to 53Hz

Single Phase With Ground

EMI Filter Move & Fuse

220v AC±1%

50 Hz 0.5Hz

Pure sine wave

800VA/640W/1500VA/1200W/3000VA/2400W

0.8

12V DC /24V DC /48V DC

Tabular

8 hours

Trip OFF

Trip OFF

Trip OFF

Optional

Continues Buzzer

<195 Change To UPS Mode

>255 Change To UPS Mode

<120 Change To inv Mode

>275 Change To inv Mode



Solar Systems Product Speci�cationSolar Inverters And Home UPS 27

Indication:

Mains/UPS On:

Charger is On (or)O�:

Over, Heavy Load &

Short Circute:

Low Battery Watt War

& Cut:

Load details:

800VA:

1500VA:

3000VA:

Transfer Time:

Line to UPS:

UPS to Line:

Environmental:

Temp:

Humidity:

Display on LCD

Display on LCD

Display on LCD

Display on LCD

#2 + #fans + 2tubes + #1PC + 1 Printer



<4 m sec

<3 m sec

0 to 50°C

0 to 95% non- Condensing



Solar Systems Product Speci�cationUltra Sun Saver Solar Charge Controller With Timer 28

Nominal Voltage:

Max. Charging current:

Discharge protection:

Over Charge Protection:

Restart Of Charging:

Reconnection of Load:

Output load current:

Battery AH Rating:

Solar Panel:

Operating Temp:

Self Consumption:

Protection:

Indications:

12V or 24V DC

5A or 10A

10.5V/21.0V

14.4V/28.8V

12.5V/25V

12.5V/25V

5A or 10A Max.

50AH or 100AH Max.

120Watts Max.

50°C

10ma

1) Battery Reverse Protection

2) Solar Panel Reverse Protection


4) Over Load Protection, Short Circuit Protection

5) Battery deep discharge protection


1) Charging on Solar

2) Battery Low, Battery Reverse

3) Over Load, SPV Reverse




Solar Systems Product Speci�cationSolar Charge Controller Cum Battery Charger 29

Nominal Voltage:







Battery AH Rating :

Solar Panel :

Operating Temp. :

Self Consumption :

Protection :

Indications :

12V or 24V DC

10A

10.5V/21.0V

14.4V/28.8V

12.5V/25V

12.5V/25V

10A Max.

100AH Max.

120Watts Max.

50°C

25ma

1) Battery Reverse Protection

2) Solar Panel Reverse Protection


4) Over Load Protection, Short Circuit Protection

5) Battery deep discharge protection

1) Charging on Solar, Charging on AC

2) Battery Low

3) Over Load, AC On

4) Battery Reverse

5) SPV Reverse



Solar Systems Product Speci�cationSolar Charge Controller 30

Rated Solar Input :

Max. Input (5min) :

System Voltage :

Maximum Solar Voltage :

Regulation Voltage :


5A Max.

6A

12V

30V

14.1V

-40°C to +65°C



Solar Systems Product Speci�cationSolar Charge Controller 31

Nominal Voltage:







Battery AH Rating :

Solar Panel :

Operating Temp. :

Self Consumption :

Protection :

Indications :

12V /24V/36V/48V DC

10A/20A/30A/ 40A/50A/75A/100A

10.5V/21.0V

14.4V/28.8V

12.5V/25V

12.5V/25V

10A Max.

100AH Max.

120Watts Max.

50°C

25ma

1) Battery Reverse Protection, Battery Over charge Protection

2) Solar Panel Reverse Protection, Over Load Protection

3) Short Circuit Protection, Battery deep discharge protection


1) Charging on Solar, Battery Low, Over Load

2) Battery Reverse, SPV Reverse


DC Power Supply System Product...

Documents

Transcript of DC Power Supply System Product...