DBALL2-NISS4HT RSR EN IG NF20170216 - Microsoft · PDF fileRev.: 20170221 Platform: DBALL2...
Transcript of DBALL2-NISS4HT RSR EN IG NF20170216 - Microsoft · PDF fileRev.: 20170221 Platform: DBALL2...
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
® Infiniti & Nissan are registered trademarks and property of their respective companies.
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.
Installation Guide
Vehicle Application Guide................................................................................................................................................
Key2GO & 1KEY.............................................................................................................................................................
Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)Type 1 - with THNISS3 T-Harness...............................................................................................................................Type 1 - without T-Harness..............................................................................................................................................Type 2 - with THNISS3 T-Harness..............................................................................................................................Type 2 - without T-Harness..............................................................................................................................................Type 3 - with THNISS3 T-Harness...............................................................................................................................Type 3 - without T-Harness..............................................................................................................................................Type 4 - with THNISS3 T-Harness...............................................................................................................................Type 4 - without T-Harness..............................................................................................................................................SmartStart/XL202 Installation Notes...............................................................................................................................
ProgrammingModule Programming......................................................................................................................................................Module Reset..................................................................................................................................................................Hard Reset......................................................................................................................................................................Feature & Option List.......................................................................................................................................................Feature Programming......................................................................................................................................................
LED Diagnostics & Troubleshooting................................................................................................................................Parking Light Error Codes...............................................................................................................................................
Limited One-Year Consumer Warranty............................................................................................................................
Quick Reference Guide...................................................................................................................................................
02
03
040509101213151618
1921212223
2426
27
28
SmartStart CompatibleSmartStart is equipped with D2D, which means it can be connected to an interface module and used in Remote Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more information.
Important!This product is NOT compatible with vehicles equipped with a manual transmission.
This guide is compatible with the NISS4HT firmware version 2.20 and higher.
Index
The NISS4HT firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Infiniti and Nissan vehicles. This guide supports the installation of a DBALL2 in Remote Start Ready (RSR) mode with or without a Plug & Play THNISS3 T-Harness. This solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF System or SmartStart (all sold separately).
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Vehicle Application GuidePage 2
The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for more information on installation wiring, programming and troubleshooting for these vehicles.
Vehicles
2016
2015
2014
2013
2012
2011
2010
2009
PK
-Im
mobili
zer
Bypass-D
ata
No
Key
Req'd
AV
-Park
ing
Lig
hts
Contr
ol
DL-A
rmF
acto
ryS
ecurity
DL-D
isarm
Facto
ryS
ecurity
DL-D
oor
Lock
Contr
ol
DL-D
oor
Unlo
ck
DL-D
river
Priority
Unlo
ck
DL-S
lidin
gD
oor
Contr
olD
river
DL-S
lidin
gD
oor
Contr
olP
assenger
DL-T
runk
/H
atc
hR
ele
ase
Key2G
O
PK
-Push
To
Sta
rtIg
nitio
nC
om
patible
RS
-3x
LO
CK
ST
AR
T(S
tart
contr
olusin
g
OE
MR
em
ote
)R
S-3
xLO
CK
ST
OP
(Sto
pcontr
olusin
gO
EM
Rem
ote
)
RS
-Rem
ote
Sta
rtR
eady
RS
-Sm
art
Sta
rt
RS
-Tach
/R
PM
Outp
ut
SS
-Entr
yM
onitoring
ALL
Door
Pin
s
SS
-Entr
yM
onitoring
Driver
Door
Pin
SS
-Entr
yM
onitoring
Hood
Pin
SS
-Entr
yM
onitoring
Tru
nk/H
atc
hP
in
ST
-Bra
ke
Sta
tus
(foot
bra
ke)
ST
-Ignitio
nS
tatu
s
ST
-Keysense
Sta
tus
Infiniti
M35h (Smart Key)* 1 1 • • • • • • • • • • • • • • • • • • • • • •
M37 (Smart Key) 1 1 1 • • • • • • • • • • • • • • • • • • • • • •
M56 (Smart Key) 1 1 1 • • • • • • • • • • • • • • • • • • • • • •
Q70 (Smart Key) 1 1 1 • • • • • • • • • • • • • • • • • • • • • •
QX56 (Smart Key) 1 1 1 • • • • • • • • • • • • • • • • • • • • • •
QX80 (Smart Key) 1 1 1 • • • • • • • • • • • • • • • • • • • • • •
Nissan
Cube (Smart Key) 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • • • •
JUKE (Smart Key) 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • • • •
LEAF (Smart Key) 2 • • • • • • • • • • • • • • • • • • • • • •
Quest (Smart Key) 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • • • • • •
Sentra (Smart Key) 1 1 1 1 • • • • • • • • • • • • • • • • • • • • • •
Versa (Smart Key) 3 3 3 3 • • • • • • • • • • • • • • • • • • • • • •
Versa Note (Smart Key) 4 4 4 • • • • • • • • • • • • • • • • • • • • • •
* The Infiniti M35h (Smart Key) is not compatible with the THNISS3D T-Harness.
Legend:
AV: Horn & Lights Controls RS: Remote Start & Engine Controls
DL: OE Door Lock & Alarm Controls SS: Integrated Security & Monitoring
PK: Transponder & Immobilizer Override ST: Function/Feature Status
When armed, the aftermarket alarm (if available) will sound if the trunk is opened using the OEM passive entry request button near the trunk. To avoid this, open the trunk using the OEM fob button, aftermarket transmitter or SmartStart application. Alternately, you can disarm the aftermarket alarm before opening the trunk.
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Page 3
This feature is mandatory to control the immobilizer override in this firmware.
Key2GO has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It uses an array of servers to generate a duplicate of the original key, allowing the installation of a remote starter without having to give up a key.
The advantage is that this feature allows you to use one original key and the server to configure the bypass in the vehicle.
All Key2GO-compatible firmware are clearly indicated in the function list of each vehicle search result page and will also appear on the flash page. Any first-time user must re-register to gain access to Key2GO, and some additional information will be required to complete the registration process, such as your Directed account number and store name.
Key2GO is compatible with XpressVIP 4.5 or higher and requires an XKLoader.
Refer to page 20 of this guide for instructions on how to program features using Key2GO.
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Q70 (Smart Key)
QX80 (Smart Key)
Cube (Smart Key)
2011-2015 JUKE (Smart Key)
Quest (Smart Key)
Sentra (Smart Key)
B01
Remote Start Safety Override Switch
Hood Pin
Note: hood pin only required on vehicles not equipped with a factory hood pin.
Wh
ite/B
lack
NOT USED
Diagnostic ConnectorOBDII
(connector side view)
T-HarnessTHNISS3
T-02 T-02
T-01 T-01
Parking light output MUST be controlled through data when using Optional T-Harness, See Feature & Option List section to enable this feature.
Important!Always connect OBDII connector BEFORE all other connections.
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
Clock & Data Wireat NATS Connector (behind Push-to-Start button)See Vehicle Wiring Reference Chart for wire location.
See Vehicle Wiring Reference Chart
Brake Pedal
B-01 B-02
Brake SwitchT-Harness
OR
(-) Driver Door Trigger: Pin 47
Diagnostic Connector OBDII (connector side view)
1 8
169
(-) PTS: Pin 4
14 5 6 7 8
32
OR
(-) PTS: Lt.Green, pin 8[2]
M37 (Smart Key)
M56 (Smart Key)
B02
2016 JUKE (Smart Key)
QX56 (Smart Key)
PTS - Brown or White 8-pin conn. (at PTS switch)
555453525150
45 46 48 4944434241 47
Junction - Black 15-pin conn.
(left of steering column)
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
[2] This connection is only for the Nissan JUKE and Nissan Sentra.
Installation Type 1 - with THNISS3 T-HarnessPage 4
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
HS CAN High: Tan/Black: 3
HS CAN High: Blue, pin 6
HS CAN Low: Pink, pin 14
HS CAN Low: Tan: 4
Immo. Data Interrupt (veh.side): Yellow: 8
Immo. Data Interrupt (conn.side): Orange/Yellow: 9
[1] (+) Parking Lights Output: Brown/Red: 12
(+) 12V: Red: 13
(+) 12V: Yellow/Red: 11
Immo. Data Output (veh.side): Orange/Black: 11
Immo. Clock Output: Yellow/Black: 10
(+) Brake Activation Output: Gray: 6
Diagnostic connector OBDII(connector side view)
1 8
169
CUT
(-) RAP Off Output: Red/Black: 4
(-) Push-To-Start Output: Green/Black: 2
[1] (-) Unlock Output: Black/White: 1
30
86 8587
87a
(+) 12V
[1] (-) Lock Output: Green/White: 3
(-) Lock, (-) Unlock wires & Parking Light See Vehicle Wiring Reference Chart.
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not
controlled by data. See features 5 & 7 in Feature and Option List section.
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
Data: Pin 3
Clock: Pin 2
White 4-pin conn.(brake switch)
(+) Brake: Pin 2
3
1 2
4
706968676665
60 61 63 6459585756 62
(+)12V: Pin 70
555453525150
45 46 48 4944434241 47
(-) Driver Door Trigger: Pin 47
(-) PTS: Pin 4
14 5 6 7 8
32
OR
(-) PTS: [2]
Lt.Green, pin 8
Junction - White 15-pin conn.(left of steering column)
Junction - Black 15-pin conn.(left of steering column)
PTS - Brown or White 8-pin conn. (at PTS switch)
N.A.T.S Antenna Connector(behind Push-to-Start button)
Page 5
Installation Type 1 - without T-Harness
[1] Only connect if you disable corresponding feature (see Feature & Option List section).
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
[2] This connection is only for the Nissan JUKE and Nissan Sentra.
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: Hood pin only required on vehicles not equipped with a factory hood pin.
(-) Ground: Black: 14
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Page 6
Type 1 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Infiniti M35h (Smart Key) 2012-2013
Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Brown 4 (-) Push-to-Start button connector. Brown 8
12V White 70 (+) BCM left of steering column. White 15
Driver Door Trigger Lt.Green 47 (-) BCM left of steering column. Black 15
Brake Violet 2 (+) Brake connector. White 4
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Lock Brown 15 (-) Power window main switch. White 16
Unlock Gray 16 (-) Power window main switch. White 16
Parking Lights Blue 2 (+) Drivers kick. White 10 or 12
Infiniti M37 (Smart Key) 2011-2013
Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Brown 4 (-) Push-to-Start button connector. Brown 8
12V White 70 (+) BCM left of steering column. White 15
Driver Door Trigger Lt.Green 47 (-) BCM left of steering column. Black 15
Brake Violet 4 (+) Brake connector. White 4
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Lock Brown or Red 15 (-) Power window main switch. White 16
Unlock Green or Gray 16 (-) Power window main switch. White 16
Parking Lights Blue 4 (+) Drivers kick. White 10 or 12
Infiniti M56 (Smart Key) 2011-2013
Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Brown 4 (-) Push-to-Start button connector. Brown 8
12V White 70 (+) BCM left of steering column. White 15
Driver Door Trigger Lt.Green 47 (-) BCM left of steering column. Black 15
Brake Violet 2 (+) Brake connector. White 4
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Lock Red or Brown 15 (-) Power window main switch. White 16
Unlock Green or Gray 16 (-) Power window main switch. White 16
Parking Lights Blue 4 (+) Drivers kick. White 10 or 12
Infiniti Q70 (Smart Key) 2014-2016
Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Brown 4 (-) Push-to-Start connector. Brown 8
12V White 70 (+) BCM left of steering column. White 15
Driver Door Trigger Lt.Green 47 (-) BCM left of steering column. Black 15
Brake Violet 2 (+) Brake connector. White 4
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Lock Red or Brown (hybrid) 15 (-) Power window main switch. White 16
Unlock Green or Gray (hybrid) 16 (-) Power window main switch. White 16
Parking Lights Blue 4 or 2 (+) Drivers kick. White 12
Infiniti QX56 (Smart Key) 2011-2013
Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data Lt. Green/Red 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Lt.Blue 4 (-) Push-to-Start connector. Brown 8
12V Yellow 70 (+) BCM left of steering column. White 15
Driver Door Trigger Gray/Red 47 (-) BCM left of steering column. Black 15
Brake Red 2 (+) Brake connector. White 2 or 4
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Lock Red 4 or 15 (-) Power window main switch. White 16
Unlock White 5 or 16 (-) Power window main switch. White 16
Parking Lights Blue/Orange 8 (+) Dash fuse box. White 10
Connector Information
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Type 1 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Infiniti QX80 (Smart Key) 2014-2016
Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data Lt. Green/Red 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Lt.Blue 4 (-) Push-to-Start connector. Brown 8
12V Yellow 70 (+) BCM left of steering column White 15
Driver Door Trigger Gray/Red 47 (-) BCM left of steering column. Black 15
Brake Red 2 (+) Brake connector. White 4
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Lock Red 15 (-) Power window main switch. White 16
Unlock White 16 (-) Power window main switch. White 16
Parking Lights Blue/Orange 8 (+) Drivers kick. White 10
Nissan Cube (Smart Key) 2009-2014
Clock Pink/Blue 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data Lt. Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Blue/Orange 4 (-) Push-to-Start connector. Brown 8
12V Yellow 70 (+) BCM left of steering column. White 15
Driver Door Trigger Brown/Yellow 47 (-) BCM left of steering column. Black 15
Brake White 2 (+) Brake connector. White 2 or 4
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Lock White/Black 8 (-) BCM behind dash fuse box. Black 40
Unlock White/Red 7 (-) BCM behind dash fuse box. Black 40
Parking Lights Brown/White 13 (+) Drivers kick. White 16
Nissan JUKE (Smart Key) 2011-2016
Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data Lt. Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Lt.Green 8 (-) Push-to-Start connector. Brown 8
12V Yellow 70 (+) BCM left of steering column White 15
Driver Door Trigger Lt.Blue 47 (-) BCM left of steering column. Black 15
Brake Red 2 (+) Brake connector. White 2 or 4
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Lock Red 8 (-) BCM behind dash fuse box. Black 40
Unlock Blue 7 (-) BCM behind dash fuse box. Black 40
Parking Lights Violet 70 (+) Drivers kick. White 100
Nissan Quest (Smart Key - w/o Power Sliding Door) 2011-2014
Clock Red 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data White 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Violet 4 (-) Push-to-Start connector. Brown 8
12V Blue 70 (+) BCM behind instrument cluster. White 15
Driver Door Trigger Green 47 (-) BCM behind instrument cluster. Black 15
Brake Lt.Green 2 (+) Brake connector. White 4
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Lock Gray 12 (-) BCM behind instrument cluster. Black 40
Unlock Brown 13 (-) BCM behind instrument cluster. Black 40
Parking Lights Red/Blue 8 (+) Dash fuse box. White 10
Nissan Quest (Smart Key - w/o Power Sliding Door) 2015-2016
Clock Gray 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data Pink 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Violet 4 (-) Push-to-Start connector. Brown 8
12V Blue 70 (+) BCM behind instrument cluster. White 15
Driver Door Trigger Green 47 (-) BCM behind instrument cluster. Black 15
Brake Lt.Green 2 (+) Brake connector. White 4
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Lock Gray 12 (-) BCM behind instrument cluster. Black 40
Unlock Brown 13 (-) BCM behind instrument cluster. Black 40
Parking Lights Red/Blue 8 (+) Dash fuse box. White 10
Wire Information Connector Information
Page 7
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Type 1 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Nissan Quest (Smart Key - w/ Power Sliding Door) 2011-2014
Clock Red 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data White 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Violet 4 (-) Push-to-Start connector. Brown 8
12V Blue 70 (+) BCM behind instrument cluster. White 15
Driver Door Trigger Green 47 (-) BCM behind instrument cluster. Black 15
Brake Lt.Green 2 (+) Brake connector. White 4
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Lock Yellow 8 (-) BCM behind instrument cluster. Black 40
Unlock White 7 (-) BCM behind instrument cluster. Black 40
Parking Lights Red/Blue 8 (+) Dash fuse box. White 10
Nissan Quest (Smart Key - w/ Power Sliding Door) 2015-2016
Clock Gray 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data Pink 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Violet 4 (-) Push-to-Start connector. Brown 8
12V Blue 70 (+) BCM behind instrument cluster. White 15
Driver Door Trigger Green 47 (-) BCM behind instrument cluster. Black 15
Brake Lt.Green 2 (+) Brake connector. White 4
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Lock Yellow 8 (-) BCM behind instrument cluster. Black 40
Unlock White 7 (-) BCM behind instrument cluster. Black 40
Parking Lights Red/Blue 8 (+) Drivers kick. White 10
Nissan Sentra (Smart Key) 2013-2016
Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data Lt. Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Lt.Green 8 (-) Push-to-Start connector. White 8
12V Yellow 70 (+) BCM left of steering column White 15
Driver Door Trigger Yellow 47 (-) BCM left of steering column. Black 15
Brake Lt.Blue to Red 2 (+) Brake connector. White 4
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Lock Violet 8 (-) BCM behind dash fusebox Black 40
Unlock Blue 7 (-) BCM behind dash fusebox Black 40
Parking Lights Violet 31 (+) Drivers kick. White 100
Wire Information Connector Information
Page 8
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Remote Start Safety Override Switch
Hood Pin
Note: hood pin only required on vehicles not equipped with a factory hood pin.
Wh
ite/B
lack
NOT USED
Diagnostic ConnectorOBDII
(connector side view)
T-HarnessTHNISS3
T-02 T-02
T-01 T-01
Parking light output MUST be controlled through data when using Optional T-Harness, See Feature & Option List section to enable this feature.
Important!Always connect OBDII connector BEFORE all other connections.
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
Clock & Data Wireat NATS Connector (behind Push-to-Start button)See Vehicle Wiring Reference Chart for wire location.
Brake Pedal
B-01 B-02
Brake SwitchT-Harness
B01
LEAF (Smart Key)
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47(-) Driver Door Trigger: Lt.Blue, pin 47
(-) PTS: Lt.Blue, pin 8
Diagnostic Connector OBDII (connector side view)
1 8
169
NOT USED
Junction - Black 15-pin conn.
(behind glove box)
14 5 6 7 8
32
PTS - White 8-pin conn. (at PTS switch)
(-) RAP Off Output: Red/Black
(-) Push-To-Start Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
See Vehicle Wiring Reference Chart
Installation Type 2 - with THNISS3Page 9
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
HS CAN High: Tan/Black: 3
HS CAN High: Blue, pin 6
HS CAN Low: Pink, pin 14
HS CAN Low: Tan: 4
Immo. Data Interrupt (vehicle side) Yellow: 8
Immo. Data Interrupt (conn.side): Orange/Yellow: 9
[1] (+) Parking Lights Output: Brown/Red: 12
(+) 12V: Red: 13
(+) 12V: Yellow/Red: 11
Immo. Data Output (veh.side): Orange/Black: 11
Immo.Clock Output: Yellow/Black: 10
(+) Brake Activation Output: Gray: 6
Diagnostic connector OBDII(connector side view)
1 8
169
CUT
(-) RAP Off Output: Red/Black: 4
(-) Push-To-Start Output: Green/Black: 2
[1] (-) Unlock Output: Black/White: 1
30
86 8587
87a
(+) 12V
[1] (-) Lock Output: Green/White: 3
(-) Lock, (-) Unlock wires & Parking Light See Vehicle Wiring Reference Chart.
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not
controlled by data. See features 5 & 7 in Feature and Option List section.
Data: Lt.Green, pin 3
Clock: Pink, pin 2
White 4-pin conn.(brake switch)
(+) Brake: Lt.Blue or Brown, pin 2
3
1 2
4
14 5 6 7 8
32(+)12V: Yellow, pin 70
N.A.T.S Antenna Connector(behind Push-to-Start button)
(-) PTS: Lt.Blue, pin 8
(-) Driver Door Trigger: Lt.Blue, pin 47
706968676665
60 61 63 6459585756 62
555453525150
45 46 48 4944434241 47
Junction - Black 15-pin conn.(behind glove box)
Junction - White 15-pin conn.(behind glove box)
PTS - White 8-pin conn. (at PTS switch)
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
Page 10
[1] Only connect if you disable corresponding feature (see Feature & Option List section).
Installation Type 2 - without T-Harness
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: Hood pin only required on vehicles not equipped with a factory hood pin.
(-) Ground: Black: 14
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Type 2 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Nissan LEAF (Smart Key) 2014
Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data Lt. Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Lt.Blue 8 (-) Push-to-Start connector. White 8
12V Yellow 70 (+) BCM behind glove box.. White 15
Driver Door Trigger Lt.Blue 47 (-) BCM behind glove box.. Black 15
Brake Lt.Blue or Brown 2 (+) Brake connector. White 4
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Parking Lights Blue or White 30 (+) Drivers kick. White 32
Lock Red 8 (-) BCM behind glove box. Black 40
Unlock Gray 7 (-) BCM behind glove box. Black 40
Wire Information Connector Information
Page 11
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Remote Start Safety Override Switch
Hood Pin
Note: hood pin only required on vehicles not equipped with a factory hood pin.
Wh
ite/B
lack
NOT USED
Diagnostic ConnectorOBDII
(connector side view)
T-02 T-02
T-01 T-01
Parking light output MUST be controlled through data when using Optional T-Harness, See Feature & Option List section to enable this feature.
Important!Always connect OBDII connector BEFORE all other connections.
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
Clock & Data Wireat NATS Connector (behind Push-to-Start button)See Vehicle Wiring Reference Chart for wire location.
Brake Pedal
B-01 B-02
Brake SwitchT-Harness
B01
Versa (Smart Key)
PTS - Brown 8-pin conn.(PTS switch)
(-) PTS: Blue, pin 8
1235 6 7 84
Diagnostic Connector OBDII (connector side view)
1 8
169
NOT USED
T-HarnessTHNISS3
(-) Driver Door Trigger: Lt.Blue, pin 18
BCMBlack 24-pin conn.
(left of steering column)
20
21
23
24
19
17
16
22
15
14
13
8
9
11
12
7
6
5
4
10
3
2
1
18
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
Installation Type 3 - with THNISS3 T-HarnessPage 12
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
HS CAN High: Tan/Black: 3
HS CAN High: Blue, pin 6
HS CAN Low: Pink, pin 14
HS CAN Low: Tan: 4
Immo. Data Interrupt (vehicle side): Yellow: 8
Immo. Data Interrupt (conn.side): Orange/Yellow: 9
[1] (+) Parking Lights Output: Brown/Red: 12
(+) 12V: Red: 13
(+) 12V: Yellow/Red: 11
Immo. Data Output (veh. side): Orange/Black: 11
Immo.Clock Output: Yellow/Black: 10
(+) Brake Activation Output: Gray: 6
Diagnostic connector OBDII(connector side view)
1 8
169
CUT
(-) RAP Off Output: Red/Black: 4
(-) Push-To-Start Output: Green/Black: 2
[1] (-) Unlock Output: Black/White: 1
30
86 8587
87a
(+) 12V
[1] (-) Lock Output: Green/White: 3
(-) Lock, (-) Unlock wires & Parking Light See Vehicle Wiring Reference Chart.
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not
controlled by data. See features 5 & 7 in Feature and Option List section.
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
Data: Lt.Green, pin 3
Clock: Pink, pin 2
(+) Brake: Lt.Green, pin 9
N.A.T.S Antenna Connector(behind Push-to-Start button)
(+)12V: Green, pin 1
1
2
Black connector(drivers kick)
615
5
716
14
413
12
11
310
2
18
9Junction - White 16-pin conn.(drivers kick)
PTS - Brown 8-pin conn.(PTS switch)
1235 6 7 84
(-) PTS: Blue, pin 8
(-) Driver Door Trigger: Lt. Blue, pin 18
BCM Black 24-pin conn.
(at drivers kick)
20
21
23
24
19
17
16
22
15
14
13
8
9
11
12
7
6
5
4
10
3
2
1
18
Page 13
[1] Only connect if you disable corresponding feature (see Feature & Option List section).
Installation Type 3 - without T-Harness
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: Hood pin only required on vehicles not equipped with a factory hood pin.
(-) Ground: Black: 14
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Function Color Pin Polarity Location Color Pins
Nissan Versa (Smart Key) 2013-2016
Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data Lt.Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Blue 8 (-) Push-to-Start connector. Brown 8
12V Green 1 (+) Driver kick. Black 2
Driver Door Trigger Lt.Blue 18 (-) Driver kick. Black 24
Brake Lt.Green 9 (+) Driver kick. White 16
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Parking Lights Red 4 (+) Drivers kick. Gray 16
Lock Gray 8 (-) BCM above drivers kick. Black 40
Unlock White 7 (-) BCM above drivers kick. Black 40
Wire Information Connector Information
Type 3 - Vehicle Wiring Reference ChartPage 14
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Remote Start Safety Override Switch
Hood Pin
Note: hood pin only required on vehicles not equipped with a factory hood pin.
Wh
ite/B
lack
NOT USED
Diagnostic ConnectorOBDII
(connector side view)
T-02 T-02
T-01 T-01
Parking light output MUST be controlled through data when using Optional T-Harness, See Feature & Option List section to enable this feature.
Important!Always connect OBDII connector BEFORE all other connections.
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
Clock & Data Wireat NATS Connector (behind Push-to-Start button)See Vehicle Wiring Reference Chart for wire location.
Brake Pedal
B-01 B-02
Brake SwitchT-Harness
B01
Versa Note (Smart Key)
PTS - White 8-pin conn.( at PTS switch)
Junction - White connector(at drivers kick)
(-) PTS: Blue or Red, pin 8
1235 6 7 84 (-) Driver Door Trigger:
Lt.Blue, pin 18
20
21
23
24
19
17
16
22
15
8
9
11
12
7
6
5
4
10
3
18
NOT USED
Diagnostic Connector OBDII (connector side view)
1 8
169
(-) Lock, (-) Unlock wires & Parking Light
See Vehicle Wiring Reference Chart.
See features 5 & 7 in Feature and Option List section.
T-HarnessTHNISS3
14 2
13 1
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
Installation Type 4 - with THNISS3 T-HarnessPage 15
(-) RAP Off Output: Red/Black
(-) Push-To-Start: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
HS CAN High: Tan/Black: 3
HS CAN High: Blue, pin 6
HS CAN Low: Pink, pin 14
HS CAN Low: Tan: 4
Immo. Data Interrupt (vehicle side): Yellow: 8
Immo. Data Interrupt (conn. side): Orange/Yellow: 9
[1] (+) Parking Lights Output: Brown/Red: 12
(-) Ground: Black: 14(+) 12V: Red: 13
(+) 12V: Yellow/Red: 11
(+) Brake Activation Output: Gray: 6
Diagnostic connector OBDII(connector side view)
1 8
169
(-) RAP Off Output: Red/Black: 4
(-) Push-To-Start Output: Green/Black: 2
[1] (-) Unlock Output: Black/White: 1
30
86 8587
87a
(+) 12V
[1] (-) Lock Output: Green/White: 3
(-) Lock, (-) Unlock wires & Parking Light See Vehicle Wiring Reference Chart.
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not
controlled by data. See features 5 & 7 in Feature and Option List section.
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
Junction White 16-conn.(at drivers kick)
PTS - White 8-pin conn.(PTS switch)
(+)12V: Green, pin 1
CUT
Data: Lt.Green, pin 3
Clock: Pink, pin 2
N.A.T.S Antenna Connector(behind Push-to-Start button)
(-) PTS: Blue or Red, pin 8
(-) Driver Door Trigger: Lt. Blue, pin 18
Junction - White 24-pin conn.
(at drivers kick)
20
21
23
24
19
17
16
22
15
14
13
8
9
11
12
7
6
5
4
10
3
2
1
18
1
2
Black 2-pin conn.(at drivers kick)
15
14
7
13
6
12
5
11
4
10 3
9 2
8 1
16
(+) Brake: Lt.Green or Red, pin 9
Immo. Data Output (veh.side): Orange/Black: 11
Immo.Clock Output: Yellow/Black: 10
1235 6 7 84
Installation Type 4 - without T-Harness
[1] Only connect if you disable corresponding feature (see Feature & Option List section).
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Page 16
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: Hood pin only required on vehicles not equipped with a factory hood pin.
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Type 4 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Nissan Versa Note (Smart Key) 2014-2016
Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
Data Lt.Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4
PTS Blue or Red 8 (-) Push-to-Start connector. White 8
12V Green 1 (+) Drivers kick Black 2
Driver Door Trigger Lt.Blue 18 (-) Drivers kick. White 24
Brake Lt.Green or Red 9 (+) Drivers kick. White 16
HS CAN High Blue 6 Data OBDII diagnostic connector. White 16
HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16
Parking Lights Red to Blue 3 (+) Drivers kick. White 24
Lock Gray 8 (-) BCM, above drivers kick. Black 40
Unlock White 7 (-) BCM above drivers kick. Black 40
Wire Information Connector Information
Page 17
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
The optional XL202 and antenna are not included and MUST be purchased separately.
Refer to the Passive Keyless Entry (PKE) Installation Guide (2102T) for detailed wiring information.
4
4
XL202
An
ten
na
XOVER
SmartStart is optional and not included. It MUST be purchased separately.
SmartStart is optional and not included. It MUST be purchased separately.
Configuration Wires (Gray & White)Connect Gray wire to (-) Ground
5 pins
D2D (4 pins, white)
4 pins
2 pins, not usedCABLE
CABLE
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL2 package.2. The modules must be connected in a specific order. Refer to the Module Programming section for more information.
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
SmartStart/XL202 Installation Notes
SmartStart Revision B
RF Kit
RF Kit & PKE Combination
Refer to the Passive Keyless Entry (PKE) Installation Guide (2102T) for detailed wiring information.
RF Kit, PKE & SmartStart BT Combination
SmartStart Revision A
LED
Prog.Button
D2D (4 pins, white)
4 pins
2 pins, not used
OR
SmartStart
Configuration Wires (White & Brown or Blue)Cut Brown or Blue Loop
LED
THIS SIDE UP
LED
DBALL2
DBALL2
DBALL2
Page 18
The DBALL Remote Start Ready (RSR) solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF Kits or SmartStart (all sold separately). This section provides specific installation information for SmartStart and XL202.
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Ensure that every key fob except one is located a minimum of 10 feet (3 meters) away from the vehicle BEFORE proceeding with the programming sequence.
Module Programming
Go to the next page to complete the module programming.
2This step is required for programming only.
Remove the backup key from the transmitter.Open the key fob and remove the battery.
REMOVEBATTERY
CR 20323V
REMOVETHE KEY
1 10-pinD2D
st1
12-pin14-pin
nd2
rd3
&Solid
Connect the 10-pin, 12-pin and 14-pin harnesses to DBALL2, then wait until the LED turns ON solid red.
Important
10-pinD2D
XL202
10-pinD2DSmartStart
OR
The DBALL2 module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBAL2L.
a. To ensure that the D2D communication between SmartStart and DBALL2 works properly, the Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue loop must be cut (Rev A SmartStart).
b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by the DBALL2 D2D connector.
Connect SmartStart to DBALL2 using the D2D port.
SmartStart Installation
Connect XL202 to DBALL2 using the D2D port.
XL202 Installation
Refer to the LED Diagnostics section on page 24-25 for more information and for troubleshooting purposes.
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL2, it is important to ensure that the proper feature and function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest version of the application.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.
When the flashing operation is successful, you can proceed with the programming instructions below.
Flashing a module using your computer:
1. Connect the interface module to your computer using the XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and select the Config for RSR button.
3. Follow the instructions to select your vehicle, installation type, and configure your options.
4. Once you have configured the firmware options, click on the FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or tablet.
3. Select FLASH YOUR MODULE and follow the on screen instructions.
Page 19
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Page 20
5 Press the brake pedal until the LED starts flashing orange slowly then release the pedal.
Push the PTS button twice to turn ON ignition and wait for the key light to flash.
Press Release
Brakepedal
Brakepedal& &
Flashesslowly
Push x2
Push the PTS button once to turn the ignition OFF.
You can now reassemble the key fob.
Push x1
Hold the key fob in front of PTS button for steps 4 to 6.
Place and hold the key fob in front of PTS button.
4
Place keyfobin front of
PTS button
6
4
3
You have successfully completed the module programming sequence.
3
2
1
Once the configuration is completed, reconnect the module. The LED turns ON solid green for 3 seconds, then turns off.
Click on Submit Key2GO Request.
Remove the module from the vehicle and reconnect it to your computer. The web site will automatically recognize that you are moving onto the second phase of the programming sequence.
Refer to the LED Diagnostics section for more information and for troubleshooting purposes.Version 4.5 or higher of XpressVIP must be installed on your computer to complete this programming sequence.
Web Programming (for Key2GO)
Solid x3 Secs
&Off
7 Disconnect the module and complete the Key2GO programming.
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
1If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
2
Solid
&Release
3 Release the programming button. The LED turns ON solid red.
Module Reset
Hard Reset
2 & &
1
Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED turns ON solid red.
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
Solid Release Solid
Solid Flashes
&Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.
Page 21
Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Feature & Option ListPage 22
It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. Manual configuration of the features is possible using the information on this page.
*Default Option
Feat. Operation Flashes / Option Description
1. No RF Output* Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Trunk* Will pop the trunk if available.
2. Right Sliding Door When available, will operate the right sliding door.
3. Left Sliding Door When available, will operate the left sliding door.
1. Trunk Will pop the trunk if available.
2. Right Sliding Door* When available, will operate the right sliding door.
3. Left Sliding Door When available, will operate the left sliding door.
1. Trunk Will pop the trunk if available.
2. Right Sliding Door When available, will operate the right sliding door.
3. Left Sliding Door* When available, will operate the left sliding door.
1. Disabled The remote starter parking lights wire must be connected in the vehicle.
2. Enabled* The parking lights will be controlled by CAN wires.
1. Disabled The vehicle is not equipped with an OEM alarm.
2. Enabled*
This feature must be enabled when the vehicle is equipped with an OEM security alarm.
The alarm original to the vehicle is disarmed using the bypass and Push-to-Start (PTS)
button.
1. Disabled The remote starter door lock wires must be connected in the vehicle.
2. Enabled - Type1 (EU) Works for most European vehicles.
3. Enabled - Type2 (US)*Works for most North American vehicles. (We've noticed that some North American
vehicles need to be set to "Type 1 (EU)" to work properly.)
1 RFTD Output Type
2 Trunk
3 Aux1
6 OEM Security Disarm On Data
7 Door Lock Control On Data
4 Aux2
5 Parking Light Control On Data
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Feature ProgrammingProgramming
Button
Page 23
To enter feature programming routine- Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button.- The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.
Changing feature options- Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the
DBALL in RSR using 3x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground will change the option for the selected feature.
- The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.
Exiting feature programming- No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.OR
- Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Page 24
LED Diagnostics & Troubleshooting
LED Description Troubleshooting
Module has no power.
Make sure the D2D harness is connected or that the 12
Volt is present between the red and black wires. If the
12 Volt is present, the module may be defective.
Waiting to begin the programming sequence.Ensure the correct programming procedure is being
followed.
Initialization failed.Reset the module and complete the programming again.
If the issue persists, please contact Technical Support.
Transponder functions were skipped.
(If compatible) when RXT mode is not desired or
convenience features are needed, please reset and
reprogram the module.
All required CAN networks has been detected. Normal operation.
1 of 2 CAN networks has been detected. Normal operation
Key2GO initiated.Please follow the steps indicated in “Module
programming” to complete the Key2GO programming.
Module was successfully programmed with all functions. Normal operation
Module was successfully programmed without
transponder functions.Normal operation.
CAN2 not detected.
Check the CAN2 Orange/Green and Orange/Brown wire
connections. Wake up the data bus by turning the
ignition on and try again. If your installation does not
require this connection, skip this step by pressing the
programming button 5 times.
J1850 not detected.Check the J1850 wire connection. Wake up the data bus
by turning the ignition on and try again.
CAN1 not detected.
Check the CAN1 Tan and Tan/Black wire connections.
Wake up the data bus by turning the ignition on and try
again. If your installation does not require this
connection, skip this step by pressing the programming
button 5 times.
Bypass data not detected.
Check the bypass line connection. If more than one wire
is used, make sure they are not inverted. Ensure the
vehicle still operates correctly using the factory key.
Bypass processing error.
The bypass calculation failed. Reset the module and try
again. If the condition persists, please contact Technical
Support.
ISO 1 not detected.
The Yellow/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
ISO 2 not detected.
The Orange/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
MUX not detected.
The Violet/Green or Violet/Brown wire did not detect the
expected voltage value. Refer to "Installation (wiring
diagrams & vehicle wiring reference charts)" to check
the connections.
Module Programming
Module Programming - Error Codes
Solid red
Flashes redx 1
Flashes redx 1
Flashes redx 2
Flashes redx 3
Flashes redx 4
Flashes redx 5
Flashes redx 6
Flashes redx 7
Solid greenx 3 secs
Flashesgreen
Solid orange
Flashes red& green
Off
Flashesorange
Flashesorangeslowly
Solid orangex 3 secs
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
LED Diagnostics & TroubleshootingPage 25
LED Description Troubleshooting
OBDII feature is not supported.The diagnostic data bus was not detected, therefore the
SmartStart features will be limited.
Ground When Running (Status) command received. The module has initialized the remote start sequence.
Ignition ON command received.The module has received the Ignition ON command and
is processing the remote start sequence.
Start ON command received.The module has received the Start ON command and is
processing the remote start sequence.
PTS shutdown error.The PTS output from the module was not activated due
to safety protection.
CAN bus incorrectly detected.
Verify the CAN1 and CAN2 connections. Refer to
“Installation (wiring diagrams & vehicle wiring reference
charts)” to check the connections.
LOCK command received.
UNLOCK command received.
TRUNK command received.
AUX1 command received.
AUX2 command received.
AUX3 command received.
Takeover successful. Normal operation.
Runsafe was not disabled.No UNLOCK command was received prior to opening the
door, or the 45 second timer expired in takeover mode.
Brake was not detected.The brakes were not detected, which prevents the
system from shutting down the vehicle.
Smart key was not detected.The smart key was not detected, which prevents the
system from shutting down the vehicle.
Speed was detected.The vehicle was detected as moving, which prevents the
system from shutting it down.
3x OEM Lock Remote Start Activation was attempted
when RFTD feature is disabled.
Activated from Web automatically when using RSR flash
tool or can be done manually. Refer to feature
programing section for more information.
Feature error.An RSR feature file mismatch was detected. Please
contact Technical Support.
RSR codes
External module synchronization
Commands
Activation Ground When Running (Status)
If the bypass module fails to flash, it did not receive the
signal. Commands can come from RF or D2D.
Shutdown codes
(Flashes red,red thenorange) x 10
Flashes red& orange
Flashes redx 21
Flashes redx 2
Flashes redx 4
Flashes redx 7
Flashes redx 9
Flashes redx 10
Flashes redx 1
Flashes redx 3
Flashesgreen
Flashesgreenquickly
Flashesgreen x 1
Flashesorange x 1
Flashesorange x 2
Flashesorange x 3
Flashesorange x 5
Flashesorange x 4
Flashesorange x 6
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Flashes Diagnostic
1 Runtime expired.
2 Over-rev shutdown.
3 Low/No RPM.
4 Transmitter shutdown.
5 Brake shutdown.
6 Hood shutdown/Remote start safety override switch is ON*.
7 Remote start safety override switch is ON*.
The parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.
* If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.
Parking Light Error CodesPage 26
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Rev.: 20170221
Platform: DBALL2Firmware: NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Page 27
Limited One Year Consumer Warranty
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
See Vehicle Wiring Reference Chart
(-) RAP Off Output: Red/Black
(-) PTS Output: Green/Black
[1] (-) Unlock Output: Black/White
[1] (-) Lock Output: Green/White
Quick Reference GuideDBALL2-NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Pit Stop ModeVehicle Takeover with Get In and Go*
4
3
1Close the vehicle doors, hood and trunk, then press the Remote Start button on the transmitter to start the vehicle.**
2
Depress the brake pedal, put the car in gear and drive off.
Enter the vehicle by opening and closing the driverdoor, while making sure the key is inside with you.
Press the Unlock button on the factory or aftermarket remote.**
Ready to drive off
Press remote start
button**
Press Unlock button on
either remote**OR
** Your aftermarket remote may differ from the model shown in the illustrations.
Enter vehicle with key fob
GG
* Get In and Go connections required.
1
2
3
Stop the vehicle in a safe parking spot and put the gear in Park (P).
* Your aftermarket remote may differ from the model shown in the illustrations.
Stop & put vehicle in Park (P)
P&
Press remote start
button*
Exit vehicle with Smart Key
The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running.
Note: We recommend that you always lock the doors of your vehicle when leaving it unattended.
It is now safe to leave the engine running and exit the vehicle with the Smart Key in hand.
Press the button to remote start the vehicle.*
The parking lights will flash once to indicate the vehicle is now in Pit Stop Mode.
Get In and Go
Get In and Go is designed to provide users with easy takeover when entering their Push-to-Start (PTS) equipped vehicle, once it has been remote started.
Typically, users would have to remote start their vehicle, then get inside and press the vehicle start button to perform a takeover. There is therefore a physical action required to drive away. With Get In and Go technology, you simply remote start the vehicle, unlock the doors, get in and go... Nothing to do but put the gear in drive and enjoy your vehicle.
This unique feature monitors a variety of parameters such as the key fob, vehicle speed sensor and door sensor, in order to perform takeover securily.
GG
Parking Light Error CodesThe parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.
Flashes Diagnostic
1 Runtime expired.
2 Over-rev shutdown.
3 Low/No RPM.
4 Transmitter shutdown.
5 Brake shutdown.
6 Hood shutdown/Remote start safety override switch is ON*.
7 Remote start safety override switch is ON*.
* If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.
Complete the following steps within 45 secondsor the vehicle will shut down.
Quick Reference GuideDBALL2-NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Button(s) Actions
Press & hold for 1 second to lock.
Press & hold for 1 second to unlock.
Press & hold for 1 second to remote
start.
Press & hold for 5 seconds to activate
the trunk release (optional).
Press once, then to activate the
rear hatch/tail glass release (optional).*
Press 3 times, then to activate
the panic mode.
Press once, then to reset the
remote starter runtime.
List of Available Commands
3x OEM Lock Remote Start Activation
x1 +
x3 +
x1 +
* This output is configurable. see your authorized installation center for more information.
Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.
This solution includes the option to remote start your vehicle by pressing the Lock button 3 times consecutively. If your vehicle allows the OEM remote to remain active while the engine is running, you may shut down your remote starter by pressing the Lock button 3 times once more.
Note: The range offered by OEM remotes is limited and typically requires you to be within eyesight of the vehicle to control it.
Remote Start Ready (RSR)
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.
Quick Reference GuideDBALL2-NISS4HT Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
SmartStart Compatible
This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com.
What is SmartStart?
Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system:
Ÿ Lock/ArmŸ Unlock/DisarmŸ Remote Car StarterŸ Trunk ReleaseŸ PanicŸ Aux Channels
You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It's easy with SmartStart!
But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more.
3.0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.
For more information, visit www.mysmartstart.com.
Notes