DATASHEET - XPRES-DROP - FTTH connectorized drop cable ...
2
Xpres-drop is a range of factory terminated drop cables to connect customers to the FTTH access networks in a fast, plug and play methodology. Every connector comes with a sealed, protective cap to prevent damage during transportation, storage, pulling and installation. The cap has an integrated pulling eye to facilitate the installation. Due to the small size, these cable assemblies can be pulled through ducts with an inner diameter as small as 20 mm and a 90° bend with an inner radius of 100mm. On installation, the protective cap is removed such the LC based termination can be installed in the EnLighten enclosures (OFDC) in a very dense stack. The cable for installation through ducts has a black LSZH outer sheet (UV resistant) such it can also be used for indoor wiring. The indoor version has a white LSZH sheet. Cable assemblies can be ordered with bend insensitive fiber conforming G657A ITU recommendations. Xpres-drop FTTH connectorized drop cable solution
Transcript of DATASHEET - XPRES-DROP - FTTH connectorized drop cable ...
Xpres-drop is a range of factory terminateddrop cables to connect customers to theFTTH access networks in a fast, plug andplay methodology.
Every connector comes with a sealed,protective cap to prevent damage duringtransportation, storage, pulling andinstallation. The cap has an integratedpulling eye to facilitate the installation. Dueto the small size, these cable assembliescan be pulled through ducts with an innerdiameter as small as 20 mm and a 90° bendwith an inner radius of 100mm.
On installation, the protective cap is removedsuch the LC based termination can beinstalled in the EnLighten enclosures(OFDC) in a very dense stack.
The cable for installation through ducts has ablack LSZH outer sheet (UV resistant) suchit can also be used for indoor wiring. Theindoor version has a white LSZH sheet.
Cable assemblies can be ordered with bendinsensitive fiber conforming G657A ITUrecommendations.
Xpres-dropFTTH connectorized drop cable solution
Tyco Electronics Raychem NVDiestsesteenweg 6923010 Kessel-Lo, BelgiumTel 32-16 351 011 (USA)1-919-557-8900Fax 32-16 351 697 (USA)1-919-557-8498www.tycoelectronics.comwww.telecomosp.comTC 1036/DS/2 06/08
Tyco Electronics and TE logo are trademarks. Kevlar is a trademark of E.I. du Pont de Nemours.
The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, Tyco Electronicsmakes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. Tyco Electronics’ obligations shall only be as set forth in Tyco Electronics’Standard Terms and Conditions of Sale for this product and in no case will Tyco Electronics be liable for any incidental, indirect or consequential damages arising out of the sale,resale, use or misuse of the product. Users of Tyco Electronics products should make their own evaluation to determine the suitability of each such product for the specific application.
Ordering information
XPRZ - X - XX - XXXM - XX
Connectorized simplex cable type
Length in meters
Connector type
Cable type
P PigtailJ Jumper
001, 002,… 010,… 100, …999M(always use three digits for cable length)
50dB UPC X160dB APC (8°) X2
ODB Indoor/Outdoor ducted (4.5m m diameter) with bend insensitive fiber G657A
LSZH jacket
Kevlar armoring
LT
Fiber
900 µ buffer
X1, X2Xpres-drop connector
Operating temperature -40 to +70°C
Insertion loss Random 100% (dB) ≤ 0.7Random 97% (dB) ≤ 0.5Random average (dB) ≤ 0.2Max. against reference connector (dB) ≤ 0.3Checked in factory 1310/1550/1625 nm
Minimum order quantity 1
IEC 61755-1 grade CTELCORDIA qualification Designed to meet
GR3120 requirements
Protective and sealed Xpres drop cap
4.5 mm
