DataSheet Power Modules - Crydom...energia a este equipo antes de trabajar con este equipo. •Ve...
4
DataSheet Power Modules B48-2T, B48-2 Series • Single and Three Phase Circuits • 5 Different Circuits to Choose from • Up to 1600 Volt Blocking Standard • UL Recognized E72445 ELECTRICAL SPECIFICATIONS Maximum DC Output Current (Tc = 85°C) Maximum Voltage Drop @ Amps Peak Operating Junction Temperature Range Symbol I D V F T J Single Phase 35 A 1.25V @ 35 A -40 - 125°C Repetitive Peak Reverse Voltage (AC Line Nominal) [Vpk] V RRM Maximum Non-Repetitive Surge Current (1/2 Cycle, 60 Hz) Maximum I²T for Fusing (t=8.3ms) [A²sec] I TSM I 2 T R JC 600 1500 0.9ºC/W V ISOL Maximum Thermal Resistance, Junction to Ceramic Base per Chip [°C/W] Isolation Voltage [Vrms] Three Phase 50 A 1.35V @ 50 A -40 - 125°C 600 1500 0.9ºC/W 400 (120 VAC) 600 (240 VAC) 800 (280 VAC) 1200 (480 VAC) 1400 (530 VAC) 1600 (600 VAC) 2500 GENERAL SPECIFICATIONS Parameters Description Weight (typical) 1.5 oz (42.5g) AVAILABLE OPTIONS Case Style -2T: Standard -2: With Isolation Barriers Series AC Line Voltage B: 400 (120VAC) C: 600 (240VAC) E: 1000 (380VAC) Circuit Type 1 2 3 4 5 (see schematic diagrams) B48 2 B -2T Required for valid part number For options only and not required for valid part number Note: Not all combinations available F: 1200 (480VAC) G: 1400 (530VAC) H: 1600 (600VAC) Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
Transcript of DataSheet Power Modules - Crydom...energia a este equipo antes de trabajar con este equipo. •Ve...
DataSheetPower Modules
B48-2T, B48-2 Series• Single and Three Phase Circuits• 5 Different Circuits to Choose from• Up to 1600 Volt Blocking Standard• UL Recognized E72445
ELECTRICAL SPECIFICATIONS
Maximum DC Output Current (Tc = 85°C)Maximum Voltage Drop @ Amps Peak Operating Junction Temperature Range
SymbolID
VF
TJ
Single Phase35 A
1.25V @ 35 A-40 - 125°C
Repetitive Peak Reverse Voltage (AC Line Nominal) [Vpk] VRRM
Maximum Non-Repetitive Surge Current (1/2 Cycle, 60 Hz)Maximum I²T for Fusing (t=8.3ms) [A²sec]
ITSM
I2TRJC
6001500
0.9ºC/WVISOL
Maximum Thermal Resistance, Junction to Ceramic Base per Chip [°C/W]Isolation Voltage [Vrms]
Three Phase 50 A
1.35V @ 50 A-40 - 125°C
6001500
0.9ºC/W
400 (120 VAC)600 (240 VAC)800 (280 VAC)
1200 (480 VAC)1400 (530 VAC)
1600 (600 VAC)
2500
GENERAL SPECIFICATIONSParametersDescription
Weight (typical) 1.5 oz (42.5g)
AVAILABLE OPTIONS
Case Style-2T: Standard-2: With Isolation Barriers
Series
AC Line VoltageB: 400 (120VAC)C: 600 (240VAC) E: 1000 (380VAC)
Circuit Type1 2 3 4 5 (see schematicdiagrams)
B48 2 B -2T
Required for valid part numberFor options only and not required for valid part number Note: Not all combinations available
F: 1200 (480VAC)G: 1400 (530VAC)H: 1600 (600VAC)
Do not forget to visit us at: www.crydom.comCopyright © 2017 Crydom Inc. Specifications subject to change without notice.
DataSheetPower Modules
Do not forget to visit us at: www.crydom.comCopyright © 2017 Crydom Inc. Specifications subject to change without notice.
B48-2B48-2T B48-2B48-2T
3
4
1
2
5
CIRCUIT DIAGRAMS
MECHANICAL SPECIFICATIONS
B48-2T B48-2
Tolerances: ±0.02 in / 0.5 mmAll dimensions are in: inches [millimeters]
Rev. 121411
E72445
Agency Approvals
2.50(63.5)1.90
(48.2)
2.50(63.5)1.90
(48.2)
.25(6.3)
MOUNTINGHOLE/SLOT0.21 (5.2) DIA.
TERMINALTERMINAL
MOUNTINGHOLE/SLOT0.21 (5.2) DIA.
1.25[31.7]
1.00[25.4]
.25(6.3)
1.06[26.9]
.50[12.9]
.55[14.0]
.10[2.5]
.10[2.5] .78
[19.7]
DataSheetPower Modules
Do not forget to visit us at: www.crydom.comCopyright © 2017 Crydom Inc. Specifications subject to change without notice.
DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. • Disconnect all
power before installing or working with this equipment.
• Verify all connections and replace all covers before turning on power.
Failure to follow these instructions will result in death or serious injury.
RIESGO DE DESCARGA ELECTRICA O EXPLOSION.
• Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo.
• Verificar todas las conexiones y colocar todas las tapas antes
de energizer el equipo.
El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias.
GEFAHR EINES ELEKTRISCHEN SCHLAGES ODER EINER EXPLOSION.• Stellen Sie
jeglichen Strom ab, der dieses Gerät versorgt, bevor
Sie an dem Gerät Arbeiten durchführen
• Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen.
Unterlassung dieser Anweisungen können zum Tode oder zu schwerenVerletzungen führen.
RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSIONE.
• Spenga tutta l'alimentazioneche fornisce questa apparecchiaturaprima di lavorarea questa apparecchiatura
• Verificare tutti i collegamenti e sostituire tutte le coperture prima dell’accensione
L'omissione di queste istruzioni provocherà la morte olesioni serie
存在电击、爆炸或电弧闪烁危险
• 在操作此设备之前请先关闭电源。
若不遵守这些说明，可能会导致严重的人身伤害甚至死亡。
WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告
RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE
• The product's side panels may be hot, allow the product to cool before touching.• Follow proper mounting instructions including torque values.• Do not allow liquids or foreign objects to enter this product.
Failure to follow these instructions can result in serious injury, or equipment damage.
Die Nichtbeachtung dieser Anweisung kannKörperverletzung oder Materialschäden zur Folge haben.
GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG
• Die Seitenwände können heiß sein. Lassen Sie das Produkt abkühlen, bevor Sie es berühren.• Beachten Sie die Montageanweisungen, • Führen Sie keine Flüssigkeiten oder Fremdkörper in das Produkt ein.
Si no se respetan estas precauciones pueden producirse graves lesiones, daños materiales.
RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD
• Los paneles laterales del producto pueden estar calientes. Esperar que el producto se enfríe antes de tocarlo.• Respetar las instrucciones de montaje, y en particular los pares de apretado.• No dejar que penetren líquidos o cuerpos extraños en el producto.
ono
La mancata osservanza di questa precauzione può causare gravi rischi per l'incolumità personale o danni alle apparecchiature.
RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO
• I pannelli laterali dell'apparecchio poss scottare; lasciar quindi raffreddare il prodotto prima di toccarlo.• Seguire le istruzioni di montaggio corrette.• Non far entrare liquidi o oggetti estranei in questo apparecchio.
如不能正确执行这些操作说明，极有可能造成严重人体伤害或者设备的损坏。
材料损坏和高温外壳的危险性
• 产品的一侧面板可能很热，在其冷却前请 不要触碰。• 遵照正确的安装说明，包括扭矩值。• 请勿让液体及其他异物进入本产品。
RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION • Eteindre
toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil
• Vérifier tousconnections, etremettre tous couverts enolace avant demettre sous
De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses.
RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER
• Les panneaux latéraux du produit peuvent être chauds. Laisser le produit refroidir avant de le toucher.• Respecter les consignes de montage, et notamment les couples de serrage. • Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit.Le non-respect de cette directive peut entraîner,des lésions corporelles graves ou des dommages matériels.
DataSheetPower Modules
Do not forget to visit us at: www.crydom.comCopyright © 2017 Crydom Inc. Specifications subject to change without notice.
ANNEX - ENVIROMENTAL INFORMATION
The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.
PartName
Toxic or hazardous Substance and Elements
Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated(Pb) (Hg) (Cd) Chromium
(Cr (VI)) biphenyls(PBB)
diphenyl ethers (PBDE)
Semiconductor die
Solder
附件 - 环保信息
此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006,电子信息产品污染控制标识要求。
有毒有害物质或元素件部
名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE)
半导体芯片
焊接点
50
