Data Projector VPL-FH500L Guide Book for FH500L.pdf · Russian, Swedish, Norwegian, Japanese,...

Data Projector

VPL-FH500L

Sales Points

High resolution WUXGA

with Full HD compatibility

Twin-lamp System

Great Lens Compatibility &

Extreme lens shift

Good TCO & ECO Friendly

Blend-in Design

6

For Dealers

For Decision makers

For User

For Decision makers

For User

NEW

7

Performance

Specification table (1/6)Name of product type VPL-FH500L (Falcon H)

Display system 3 LCD system

Display device

Size of effective

display area0.95” (24.1 mm) x 3, aspect ratio: 16:10

Number of pixels 6,912,000 (1920 x 1200 x 3) pixels

Projection lens

Zoom Powered / Manual (Depend on lens)

Focus Powered / Manual (Depend on lens)

Lens shift Powered

Light source High-pressure mercury lamp 330 W type

Recommended lamp replacement time*1

6000 H (Lamp mode : High) / 8000 H (Lamp mode : Standard) *2

Filter replacement cycle Same time as the lamp replacement

Screen size 40” to 600'„ (1.02 m to 15.24 m) (Depend on lens)

Light output 7000 lm (Lamp mode: High) / 5600 lm (Lamp mode: Standard) *3

Color light output 7000 lm (Lamp mode: High) / 5600 lm (Lamp mode: Standard) *3

Contrast ratio (full white/full black)*4

2500:1

*1: The figures are approximate. They vary depending on the environment or how the projector is used. Jigyobu cannot guarantee them.

*2: With two lamp sequential use.

*3: When attaching the VPLL-ZP41

*4: This value is average with lamp dimming.

NEW

This color texts are different points from FX500

8

Performance


Speaker No

Displayable

scanning frequency

Horizontal 14 kHz to 93 kHz

Vertical 47 Hz to 93 Hz

Display resolution Computer signal

input

Maximum display resolution: 1920 x 1200 dots*5

Panel display resolution: 1920 x 1200 dots

Video signal input NTSC, PAL, SECAM, 480/60i, 576/50i, 480/60p, 576/50p, 720/60p, 720/50p, 1080/60i,

1080/50i, 1080/60p, 1080/50p, 1080/48i*６

, 1080/24p, 1080/30p*６

Color system NTSC3.58, PAL, SECAM, NTSC4.43, PAL-M, PAL-N, PAL60

Keystone correction Vertical: Max. +/- 5 degrees

OSD language 20-languages (English, Dutch, French, Italian, German, Spanish, Portuguese ,Turkish, Polish,

Russian, Swedish, Norwegian, Japanese, Simplified Chinese, Traditional Chinese, Korean,

Thai, Vietnamese, Arabic, Persian)

*5: Available for VESA Reduced Blanking signal.

*6: Available via BKM-FW16

NEW


9

Performance


Computer and Video

signal input/outputINPUT A RGB / Y PB PR input connector: 5BNC (female)

INPUT B RGB input connector: Mini D-sub 15-pin (female)

INPUT C DVI-D input connector: DVI-D 24-pin (Single link), supported HDCP

INPUT D HDMI input connector: Digital RGB/Y PB PR

INPUT E Optional adapter slot (For HD-SDI/SDI Input Adapter “BKM-FW16”)

S VIDEO IN S video input connector: Mini DIN-4 pin

VIDEO IN Video input connector: BNC

OUTPUT Monitor output connector*7

: Mini D-sub-15 pin (female)

Control signal input/output RS-232C connector: D-sub-9 pin (female)

LAN connector: RJ45, 10BASE-T/100BASE-TX

Control S input connector: Stereo mini jack, Plug in power DC5V

Control S output connector: Stereo mini jack

*7: From INPUT A (RGB/YPBPR) and INPUT B (RGB)

NEW


10

Performance


Acoustic noise 39 dB (Lamp mode: High) / 35 dB (Lamp mode: Standard)

Operating temperature (Operating

humidity)0°C to 40°C / 32°F to 104°F (35% to 85% (no condensation))

Storage temperature (Storage humidity) -20°C to +60°C / -4°F to +140°F (10% to 90%)

Power requirements AC 100 V to 240 V, 4.9 A to 2.0 A, 50 Hz / 60 Hz

Power consumption AC 100 V to 120 V 490 W

AC 220V to 240 V 460 W

Standby mode

power consumption

AC 100 V to 120 V 11 W (Standby mode: Standard) / 0.1 W (Standby mode: Low)

AC 220V to 240 V 10 W (Standby Mode: Standard) / 0.2 W (Standby mode: Low)

Heat dissipation AC 100 V to 120 V 1672 BTU

AC 220V to 240 V 1569 BTU

MTBF 28,039 H

Safety regulations WW model UL60950-1 2nd Edition, cUL (No.60950-1 2nd Edition), FCC/IC Class A, CE EN60950-1 2nd

Edition (LVD,EMC), C-Tick, 電気用品安全技術基準省令２項, VCCIクラスA情報技術装置, 電

源高調波自主規制 JIS C 61000-3-2, 電気通信事業法技術基準（10/100Base）, GOST-R

Body color White / Gray

Outside dimensions W 530 x H 213 x D 545 mm / W 20 7/8 x H 8 3/8 x D 21 15/32 in

W 530 x H 204 x D 545 mm / W 20 7/8 x H 8 1/32 x D 21 15/32 in

(without protrusions)

Mass 20 kg / 44 lb 1 oz

The values for mass and dimensions are approximate.

NEW


11

Performance


Supplied accessories RM-PJ19 Remote Commander (1)

Size AA (R6) batteries (2)

AC Power Cord (1) (@local)

Cable ties (2)

Cable tie holder for HDMI (1)

Lens installation screws (4)

Lens gap cover (1)

Quick Reference Manual (1)*8

Warranty Card (1) (@local)*9

Security Label (1)

Operating Instructions: CD-ROM*10

(1)

Battery for the

remote commander

of the projector

Category Battery Manganese

Type Size AA (R6)

Weight of single

battery (g)Approx. 18g

Number of batteries

per package2

*8: World Wide model only. Languages are JP/GB/FR/DE/IT/ES/CS. Lens replacement instructions to be added

*9: When revise warranty period, must consult with Jigyoubu

*10: CD-ROM contents: Operating Instructions (JP/GB/FR/DE/IT/ES/CS/RU) Installation manual is to be integrated into operating instruction.

NEW


12

Performance


Optional accessories

Projector Lamp (for replacement) : LMP-F330

Projector Suspension Support: PSS-630

Projector Suspension Support Joint Pole: PSS-630P

Projection Lens: VPLL-FM22

Projection Lens: VPLL-ZM32


Projection Lens: VPLL-ZP41


Projection Lens: VPLL-4008

Projection Lens: VPLL-Z4015




Projection Lens Adapter: PK-F500LA1

Projection Lens Adapter: PK-F500LA2

HD-SDI/SDI Input Adaptor: BKM-FW16

NEW


Functions Picture by Picture (TWIN)

DICOM GSDF simulation gamma

Screen Aspect

V Center & Vertical Size

Panel Alignment

Color Matching

Picture Muting -Mechanical Shutter-

ECO Mode

Security Pack

Network

Discrete Power key

Test Pattern

Digital Zoom

Smart APA (Auto Pixel Alignment)

Freeze

Configuration Reset

ID Mode

Closed Captioning (CC Display)

Direct Power On/Off

Installation Attitude

High Altitude Mode13

NEW

Changed

Same as FX500, refer its PIL

Functions

Picture by Picture (TWIN)

14

This function simultaneously displays two different pictures

Case 1: Video Conference

Case 2: Using two materials

TWIN

Input signals combinations

Only form

INPUT B (Fixed)

NEW

Functions

DICOM GSDF Simulation gamma

15

The new WUXGA models have new gamma mode

“DICOM GSDF Simulation” with Input C (DVI) & D

(HDMI with computer signals)

It improves the reproduction of high-definition data

that is used for medical training, etc,.

Conforms to GSDF (Grayscale Standard Display

Function) of medical standards for DICOM (Digital

Imaging and Communications in Medicine).

*This function is for training and reference only, cannot be

used for medical diagnosis

Applicable contents;

Medical pictures such as X-ray, CT and MRI etc.

Target applications;

University, Hospital, Medical center, etc.

- Medical Education

- Academic Conference

Gamma Curve

0

20

40

60

80

100

0 200 400 600 800 1000

Input (10bit)

Outp

ut

Lum

inace [

%]

DICOM

2.2

DICOM GSDF sim.

Standard 2.2

More visible than standard gamma

NEW

Functions

Screen Aspect

16

When the aspect ratio of screen and image does not match*, this function allows to fit

projected image to the screen. So even image are switched between different aspect

signals, always the projected image can be fit into the screen.*Using same aspect between screen and projector is ideal

Previous products had fitting issues. Projected Image or Some OSD messages are out of screen

Panel Screen 16:10 signal 16:9 signal 4:3 signal

16:10 16:9Out of

the screenOK

Out of

the screen

4:3Out of

the screenOK

Out of

the screen

By setting the “Screen Aspect” via OSD menu (with electric compression)

16:10

Panel Screen 16:10 signal 16:9 signal 4:3 signal

16:10OK OKOK

OKOKOK

16:9

4:3

16:10 OK OK OK

OK OK OK

NEW

Functions

V Center & Vertical Size

17

These functions allow you to adjust the subtitle position in movie contents.

Input signal Customer likes to

zoom for bigger size Adjust V Center

Subtitle to be visible, some of upper side is invisible instead

Panel area

Gray area (Subtitle) is behind

Vertical Size

Vertical compression

Input signalCustomer likes to

zoom for bigger size Adjust V Size

V Center

Subtitle to be visible

NEW

Functions

Panel Alignment

18

Adjustable range

- Shift

Shifts the whole picture

Adjustment range : ± 2.0dot by 0.1

This feature allows you to adjust the gaps in the color of characters or the picture

- Zone

Selects the desired range

(H:16 x V:10 = 160 cross points)

Adjustment range : ± 2.0dot by 0.1

NEW

Functions

Color Matching

19

For correcting the brightness and color of the whole projected image

manually from the signal level in six steps

Dealers can adjust easier than previous in the field.*The brightness and color of the projected image may not match completely, even after you adjust

“Brightness” and “Color.”

Reference picture

Adjust

NEW

You can cut mute the image by just a one press of dedicated key on

remote commander. You can resume it by pressing again.

Functions

Picture Muting -Mechanical Shutter-

MUTING

“PIC”The projection

is cut off

20

Mechanical Shutter

From this product, shutter timing has been changed (FX500L‟s timing will be also changed as running change).

- Before: Shutter closes after “Muting On” message disappeared (Approx. 3sec.)

- After: Shutter Immediately closes

Changed

Functions

ECO Mode

21

Lamp mode “High / Standard”

- Saving the consumption of lamp wattage.

Power Saving mode “Lamp Cutoff / Standby / Off”

- When set to "On“, goes into power saving mode if

there is no operation for 10 minutes without any

signal input.

Lamp Cutoff ; The lamp goes off. The lamp lights again when a

signal is input or any key is pressed.

Standby ; The projector goes into Standby mode. To use it, turn

on the power again.

Standby mode “Standard / Low”

- “Low” can reduce power consumption in standby*

*Network function cannot be operated

Power status VPL-FH500L

AC100V

to

AC120V

Power

consumption

High 490W

Std Approx. 80%

StandbyStd 11W

Low 0.1W

AC220V

to

AC240V

Power

consumption

High 460W

Std Approx. 80%

StandbyStd 10W

Low 0.2W

Can optimize combinations of following functions.

OSD menu

Direct keys

Same as FX500

Other Product Information

Connector Panel

On Screen Menu

Preset Signals

Installation Diagram

Replacement Lamp

Remote Commander (RM-PJ19)

Control Panel

Replacing Lamp

Replacing Air Filter

Lens Replacement

Dimensions

Installation Conditions

Installation Positioning

22

Same as FX500, refer its PIL


Connector Panel

23


On Screen Menu (1/7)

24

UI design will be new.

Meet the Sony UI design

For impression as new generation

Current New

Input

pallet

For user friendly, shows each

input status as list. Can be

shown by pressing input key of

projector.

1. Connector shape

2. When detect input signal,

icons are shown. (Not displayed

during TWIN picture mode)

Menu

Items Options Initial Setting Note

Picture Mode Dynamic/Standard/Presentation Presentation (Computer

signal)/Standard (Video

signal)

"Presentation" is available for

computer signal only

Reset ーーー

Contrast 0-100 80(TBD)

Depend on Picture Mode

Init Value for China Model is 50.

Brightness 0-100 50(TBD)

Depend on Picture ModeColor 0-100 50(TBD)


For video signal only (except Black

and white signal)Hue 0-100 50(TBD)


For video signal only

(NTSC3.58/NTSC4.43 when analog

TV video signal is input and except

Black and white signal)Color Temp. High/Middle/Low/Custom 1/Custom

2/Custom 3

Low(TBD)


Not available when "Picture Mode" is

set to "Presentation"

Sharpness 0-100 50(TBD)


For video signal only

Sharpness 0-100 50(TBD)


For computer signal available

Expert Setting Film Mode Auto/Off Auto For video signal except progressive

video signal onlyExpert Setting Black Level Adj. High/Low/Off Off For video signal only

Expert Setting Gamma Mode Graphics/Text Graphics For computer signal only

Expert Setting Gamma Mode Graphics/Text/DICOM GSDF Sim. Graphics For computer signal only

"DICOM GSDF Sim." is available for

DVI only.


On Screen Menu (2/7) Picture

25

NEW items are added

This combination setting

for DLP shoot out

- Input signals and adjustable/setting items Some of the items in the menus cannot be adjusted depending on the input signal as indicated in the right tables.

The items that cannot be adjusted are not displayed in the menu.

- Picture mode is memorized per input sources: 1. PC, 2. SD (480p/480i etc.), 3. HD (720p/1080p/1080i etc.)

NEW



26

Screen

- Input signals and adjustable/setting items

Some of the items in the menus cannot be adjusted depending on the input signal as indicated in the right tables. The items that cannot be adjusted are not displayed in the menu.

- Aspect mode is memorized per input channels

- Over Scan, Phase, Pitch and shift are memorized per signals as below.

1. Video60 NT358/NT443/BW60 / 2. AL/SECAM/PALM/PALN/BW50 / 3, 15k60 RGB/COMPONENT / 4, 15k50 RGB/COMPONENT / 5, P. Component480/60p / 6, 575/50p

7, HDTV 1035/60i&1080/60i / 8, 1080/50ｉ / 9, 1080/24PsF /10, 720/60p / 11, 720/50p / 12, 1080/60P / 13, 1080/50P


When the computer

signal is input

Normal/Full1/Full2 Full1 ー

When the video

signal is input

4:3/16:9/Zoom 4:3 (SD video signal)/16:9 (HD

video signal)

ー

When the computer

signal is input

Normal/Full1/Full2 Full1 ー

When the video

signal is input

4:3/16:9/Full/Zoom 4:3 (SD video signal)/16:9 (HD

video signal)

ー

V Center -5 - 5 0

Vertical Size -5 - 5 0

Over Scan On/Off On For video signal via Y PB PR input connector only

For video signals via except Video/S-Video inputs

Over Scan On/Off Off (Input Ch excepet for

Video/S-Video)

On (Video/S-Video Input Ch)

For video signal via Y PB PR input connector only

For video signals via except Video/S-Video inputs

APA ーー

Phase 0-31 50　⇒　Depend on signal

Pitch 0-100　⇒　Depend on signal 50　⇒　Depend on signal

Shift H：0-100 ⇒ Depend on signal

V：0-100

H：50　⇒　Depend on

signal

V：50　⇒　Depend on signal

For computer signal via RGB input connector and

video signal via Y PB PR input connector only

⇒For computer signal and Video signal via RGB input

connector only

For computer signal via RGB input connector.

Aspect

Adjust Signal

Aspect


Language English/Dutch/French/Italia

n/German/Spanish/Portugu

ese/Russian/Swedish/Norw

egian/Japanese/Chinese

(Simplified

Chinese)/Chinese

(Traditional

Chinese)/Korean/Thai/Arabi

c/Turkish/Polish/Vietnames

e/Persian

English Options are shown by each

local language

Menu Position Bottom Left/Center Bottom Left

On/Off On ー

IR Receiver Front & Rear/Front/Rear Front & Rear ー

ID Mode All/1/2/3 All ー

Security Lock On/Off Off ー

Panel Key Lock On/Off Off ー

Lens Control On/Off On ー

Status



27

FunctionEnglish


Smart APA On/Off On APA is available for

computer signal via RGB

input connector onlyOff/CC1/CC2/CC3/CC4/TE

XT1/TEXT2/TEXT3/TEXT4

Off ー

Pic.Muting Mode Shutter/Image Shutter ー

Lamp Mode High/Standard Standard ー

Lamp Light Mode Auto/Lamp1/Lamp2 Lamp 1 ー

Background Blue/Black Blue ー

Start Up Image On/Off On ー

CC Display

Operation NEW items are added

NEW



28

Connection/PowerEnglish


IP Address Setup Auto (DHCP)/Manual Auto (DHCP) ー

IP Address/Subnet

Mask/Default

Gateway/Primary

DNS/Secondary

DNS/Apply

ーーー

Input-A Signal Sel. Auto/Computer/Video

GBR/Component

Auto ー

Color System Auto/NTSC3.58/PAL/SECA

M/NTSC4.43/PAL-M/PAL-N

Auto ー

Standby Mode Standard/Low Standard ー

Power Saving Mode Lamp Cutoff/Standby/Off Off ー

Direct Power On On/Off Off ー

Network Setting


Image Flip HV/H/V/Off Off ー

Installation Attitude Right Side Up/Upside

Down/Front Up/Front Down

Right Side Up ー

High Altitude Mode On/Off Off ー

Screen Aspect 16:10/16:9/4:3 16:10

V Keystone -20 - 20 0 ー

Panel Alignment On/Off Off ー

Adjuset Item Shift/Zone Shift

Adjust Color R/B R

Pattern Color RG/RGB RG

Adjust ー

Color Matching Adjuset/Reset ーー



29

Installation NEW items are added

NEW



30

InformationEnglish


Model Name ーーー

Serial Number ーーー

fH/fV ーーー

Signal Type ーーー

Lamp Timer ーーー


Preset Signals

31

NEW

32


Installation Diagram (1/2)

NEW

33


Installation Diagram (2/2)

NEW


Replacement Lamp

Is Krypton 85 used ? (especially for USA)

⇒ No

*: These figures are approximate. They vary depending on the environment or how the projector is used.

Jigyobu cannot guarantee them. Please be careful when disclosing the lamp life not to make any

misunderstanding that customers recognize the figures as “warranty.”

Brightness Maintenance : 50% (typical) / Life Survival Rate : 50%, this conditions are strictly confidential

and internal use only.

Model VPL-FH500L / FX500L

Optional Lamp LMP-F330

Type 330W

Recommended

replacement time*

High 3000 H

Standard 4000 H

Accessories Four electrostatic filters

Over view

34

Same as FX500

Data Projector VPL-FH500L Guide Book for FH500L.pdf · Russian, Swedish, Norwegian, Japanese,...

Documents

Transcript of Data Projector VPL-FH500L Guide Book for FH500L.pdf · Russian, Swedish, Norwegian, Japanese,...