DAHLIA S - JSPR
19
+ + DAHLIA S ASSEMBLY ASSEMBLY DAHLIA S CONTACT JSPR T +31 (0) 402692111 [email protected] WWW.JSPR.EU
Transcript of DAHLIA S - JSPR
++
DAHLIA S ASSEMBLY
ASSEMBLY DAHLIA S
CONTACT
JSPRT +31 (0) 402692111
WWW.JSPR.EU
++
DAHLIA S ASSEMBLY
1.
3.
4.
1x 1x 1x15x
Carefully unpack the light fixture. Box contains 15x aluminum petals; 1x center piece; 1x lock ring; 1x canopy; assembly screws.
Carefully unpack the petals (15x) and sort them by number or letter. Each petal is marked either with the numbers 1, 2, 3; the letter ‘S’ for standard (9 identical pieces); or 13, 14, 15.
2.
Place the center piece (light down) on included assembly block.
21 3 s 1413 15
Place petal marked ‘1’ anywhere on the center piece. Insert one side, leave 3 empty holes/slits and insert the other side of the petal.
NOTE: All petals are place form top and clockwise.
! Assembly and installation should be carried out by a prossesional.
nr. 1
1 32
2.
2.
++
DAHLIA S ASSEMBLY
Starting with the fifth petal each side is placed in the same hole/slit next to a previously added petal.
Continue adding petals marked 2 and 3 clockwise the same way leaving 3 empty holes between each side of the petal.
nr. 1nr. 2
nr. 3
Fifth petal must be placed in the same slit as the first petals’ end (drawing below). Continue adding the reminaing ‘S’ marked petals, overlapping the previuous ones.
nr. 1nr. 2
nr. 3
‘S’
‘S’
‘S’
‘S’
‘S’‘S’
‘S’
‘S’
‘S’
++
DAHLIA S ASSEMBLY
7.
9. 10.
Once all petals are in place put the lock ring over the petals.
Carefully screw in the provided screws to fully lock the petals to the centerpiece.
The fixture is ready for installation.
8.
Align the lock ring holes with the center piece hole pattern.
Finish the fixture by hooking in the last 3 petals with markings nr. 13; nr. 14; nr. 15. The last fifteenth piece will lock the pattern with the first one.
nr. 1
nr. 13
nr. 14
nr. 15 nr. 2
nr. 3
‘S’
‘S’
‘S’
‘S’
‘S’‘S’
‘S’
‘S’
‘S’
++
DAHLIA M ASSEMBLY
ASSEMBLY DAHLIA M
CONTACT
JSPRT +31 (0) 402692111
WWW.JSPR.EU
++
DAHLIA M ASSEMBLY
1.
3.
4.
1x 1x 1x20x
Carefully unpack the light fixture. Box contains 20x aluminum petals; 1x center piece; 1x lock ring; 1x canopy; assembly screws.
Carefully unpack the petals (20x) and sort them by number or letter. Each petal is marked either with the numbers 1, 2, 3, 4, 5; the letter ‘S’ for standard (10 identical pieces); or 16, 17, 18, 19, 20.
2.
Place the center piece (light down) on included assembly block.
21 3 s 1716 18
Place petal marked ‘1’ anywhere on the center piece. Insert one side, leave 5 empty holes/slits and insert the other side of the petal.
NOTE: All petals are placed form top and clockwise.
! Assembly and installation should be carried out by a prossesional.
nr. 1
1 532 4
2.
2.
++
DAHLIA M ASSEMBLY
Starting with the seventh petal each side is placed in the same hole/slit next to a previously added petal.
Continue adding petals marked 2; 3; 4; 5 clockwise leaving 5 empty holes between each side of the petal. Follow the cuttouts on the petals.
nr. 1nr. 2
nr. 3
nr. 4
nr. 5
Seventh petal must be placed in the same slit as the first petals’ end (drawing below). Continue adding the reminaing ‘S’ marked petals, overlapping the previous ones.
nr. 1nr. 2
nr. 3
nr. 4
nr. 5
‘S’
‘S’
‘S’
‘S’
‘S’‘S’
‘S’
‘S’
‘S’
‘S’
++
DAHLIA M ASSEMBLY
7.
9. 10.
Once all petals are in place put the lock ring over the petals.
Carefully screw in the provided screws to fully lock the petals to the centerpiece.
The fixture is ready for installation.
8.
Align the lock ring holes with the center piece hole pattern.
Finish the fixture by hooking in the last 5 petals with markings nr. 16; nr. 17; nr. 18; nr. 19; nr. 20. The last 20th piece will lock the pattern with the first one.
nr. 1nr. 2
nr. 3
nr. 4
nr. 5
nr. 16
nr. 17
nr. 18
nr. 19
nr. 20
‘S’
‘S’
‘S’
‘S’
‘S’‘S’
‘S’
‘S’
‘S’
‘S’
++
DAHLIA L ASSEMBLY
ASSEMBLY DAHLIA L
CONTACT
JSPRT +31 (0) 402692111
WWW.JSPR.EU
++
DAHLIA M ASSEMBLY
1.
3.
4.
1x 1x 1x25x
Carefully unpack the light fixture. Box contains 25x aluminum petals; 1x center piece; 1x lock ring; 1x canopy; assembly screws.
Carefully unpack the petals (25x) and sort them by number or letter. Each petal is marked either with the numbers 1, 2, 3, 4, 5, 6; the letter ‘S’ for standard (13 identical pieces); or 20, 21, 22, 23, 24.
2.
Place the center piece (light down) on included assembly block.
21 3 s 1716 18
Place petal marked ‘1’ anywhere on the center piece. Insert one side, leave 6 empty holes/slits and insert the other side of the petal.
NOTE: All petals are placed form top and clockwise.
! Assembly and installation should be carried out by a prossesional.
1 5 632 4
2.
2.
++
DAHLIA L ASSEMBLY
Starting with the 8th petal each side is placed in the same hole/slit next to a previously added petal.
Continue adding petals marked 2; 3; 4; 5; 6 clockwise leaving 6 empty holes between each side of the petal. Follow the cuttouts on the petals.
nr. 1 nr. 2nr. 3
nr. 4
nr. 5
nr. 6
nr. 1 nr. 2nr. 3
nr. 4
nr. 5
nr. 6
Eighth petal must be placed in the same slit as the first petals’ end (drawing below). Continue adding the reminaing ‘S’ marked petals, overlapping the previous ones.
‘S’
‘S’
‘S’
‘S’
‘S’
‘S’‘S’‘S’
‘S’
‘S’
‘S’
‘S’
‘S’
++
DAHLIA L ASSEMBLY
7.
9. 10.
Once all petals are in place put the lock ring over the petals.
Carefully screw in the provided screws to fully lock the petals to the centerpiece.
The fixture is ready for installation.
8.
Align the lock ring holes with the center piece hole pattern.
Finish the fixture by hooking in the last 6 petals with markings nr. 20; nr. 21; nr. 22; nr 23; nr. 24; nr. 25. The last 25th piece will lock the pattern with the first one.
nr. 1 nr. 2nr. 3
nr. 4
nr. 5
nr. 6
nr. 20
nr. 21
nr. 22
nr. 23
nr. 24
nr. 25
‘S’
‘S’
‘S’
‘S’
‘S’
‘S’‘S’‘S’
‘S’
‘S’
‘S’
‘S’
‘S’
++
DAHLIA WALL LIGHT ASSEMBLY
ASSEMBLY
DAHLIA WALL LIGHT
CONTACT
JSPRT +31 (0) 402692111
WWW.JSPR.EU
++
DAHLIA S ASSEMBLY
1.
3.
4.
1x 1x 1x15x
Carefully unpack the light fixture. Box contains 15x aluminum petals; 1x center piece; 1x lock ring; 1x canopy base; assembly screws.
Carefully unpack the petals (15x) and sort them by number or letter. Each petal is marked either with the numbers 1, 2, 3; the letter ‘S’ for standard (9 identical pieces); or 13, 14, 15.
2.
Place the center piece (light down) on included assembly block.
21 3 s 1413 15
Place petal marked ‘1’ anywhere on the center piece. Insert one side, leave 3 empty holes/slits and insert the other side of the petal.
NOTE: All petals are place form top and clockwise.
! Assembly and installation should be carried out by a prossesional.
nr. 1
1 32
2.
2.
++
DAHLIA S ASSEMBLY
Starting with the fifth petal each side is placed in the same hole/slit next to a previously added petal.
Continue adding petals marked 2 and 3 clockwise the same way leaving 3 empty holes between each side of the petal.
nr. 1nr. 2
nr. 3
Fifth petal must be placed in the same slit as the first petals’ end (drawing below). Continue adding the reminaing ‘S’ marked petals, overlapping the previuous ones.
nr. 1nr. 2
nr. 3
‘S’
‘S’
‘S’
‘S’
‘S’‘S’
‘S’
‘S’
‘S’
++
DAHLIA S ASSEMBLY
7.
9. 10.
Once all petals are in place put the lock ring over the petals.
Carefully screw in the provided screws to fully lock the petals to the centerpiece.
The fixture is ready for installation.
8.
Align the lock ring holes with the center piece hole pattern.
Finish the fixture by hooking in the last 3 petals with markings nr. 13; nr. 14; nr. 15. The last fifteenth piece will lock the pattern with the first one.
nr. 1
nr. 13
nr. 14
nr. 15 nr. 2
nr. 3
‘S’
‘S’
‘S’
‘S’
‘S’‘S’
‘S’
‘S’
‘S’
++
DAHLIA INSTALLATION
CONTACT
JSPRT +31 (0) 402692111
WWW.JSPR.EU
220V / 110V
Mark holes in the ceiling based on canopy measurements. Attach canopy base plate using screws and dowels (by client).
Carefully lift the fixture and feed the suspension cables in the premounted canopy. Continue aligning them to achieve a perfectly balenced possition.
NOTE: JSPR ceiling canopy fasteners work the same way as the individual fasteners. Manual for their use is enclosed in this document
Tuck any excess electricity cable in the canopy and the fixture is ready.
! Assembly and installation should be carried out by a prossesional.
Determine the light fixtures aproximate length, shorten the cable from the lamp leaving extra length and pull through the canopy cover. Connect the lamps electricity cable to the house electric cable.
NOTE:JSPR advised dimmers can be placed in the Dahlia canopy.
Align the canopy cover to the base plate and fix the canopy with the provided screws.
1.
4. 5.
2. 3.
1. 2. 3. 4.
++
JSPR SUSPENSION CABLE FASTENERS USE
GUIDING THE CABLE (Steps 1 - 3)
Once the cable fasteners are securely attached to the ceiling, guide the support cable through the tinny nozzle (1 & 2 ). Once reached the desired lenght of the cable let it go or pull cable downwards and the cable fastener will automatically lock (3).
EXTENDING THE CABLE (Step 4)
To extend the cable, push the little nozzle upwards/inside, the cable will loosen and allow to be pulled out. To fix release the nozzle and the fastener will automatically lock the cable.
After achieving desired length of the lighting fixture trim any excess cables.
GUIDE SHORTEN FIX LENGTHEN/RELEASE
++
DAHLIA WALL LIGHT INSTALLATION
CONTACT
JSPRT +31 (0) 402692111
WWW.JSPR.EU
220V / 110V
Mark and drill holes in the wall near the house electricity wire. Attach the bracket using screws and dowels (by client) and pull through the electricity through the center.
Connect the fixtures electricity cable to the house electic cable. Alight the screw holes of the lamp and the wall bracket and push the light over the bracket.
Fix the light fixture to the wall by screwing provided screws. Screw them tight to avoid damage.
NOTE:JSPR advised dimmers can be placed in the Dahlia wall fixture.
The light fixture is ready.
! Assembly and installation should be carried out by a prossesional.
1.
4. 5.
3.
