DAC5662-EP (Rev. A) - Analog, Embedded Processing ... · DE MUX DA[11:0] DB[11:0] MODE GSET Latch A...
-
Upload
trinhkhuong -
Category
Documents
-
view
214 -
download
0
Transcript of DAC5662-EP (Rev. A) - Analog, Embedded Processing ... · DE MUX DA[11:0] DB[11:0] MODE GSET Latch A...
www.ti.com
FEATURES
APPLICATIONS
DESCRIPTION
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
DUAL 12-BIT 200-MSPS DIGITAL-TO-ANALOG CONVERTER
• High Spurious-Free Dynamic Range (SFDR):85 dBc at 5 MHz• Controlled Baseline
• High Third-Order Two-Tone Intermodulation– One Assembly(IMD3): 78 dBc at 15.1 and 16.1 MHz– One Test Site
• WCDMA Adjacent Channel Leakage Ratio– One Fabrication Site(ACLR): 70 dB at 30.72 MHz
• Extended Temperature Performance of• Independent or Single Resistor Gain Control–55°C to 125°C• Dual or Interleaved Data• Enhanced Diminishing Manufacturing• On-Chip 1.2-V ReferenceSources (DMS) Support• Low Power: 330 mW• Enhanced Product-Change Notification• Power-Down Mode: 15 mW• Qualification Pedigree (1)
• Package: 48-Pin Thin Quad Flat Pack (TQFP)• 12-Bit Dual Transmit Digital-to-AnalogConverter (DAC)
• 200-MSPS Update Rate• Cellular Base Transceiver Station Transmit• Single Supply: 3 V to 3.6 V Channel
(1) Component qualification in accordance with JEDEC and – CDMA: W-CDMA, CDMA2000, IS-95industry standards to ensure reliable operation over anextended temperature range. This includes, but is not limited – TDMA: GSM, IS-136, EDGE/UWC-136to, Highly Accelerated Stress Test (HAST) or biased 85/85, • Medical/Test Instrumentationtemperature cycle, autoclave or unbiased HAST,electromigration, bond intermetallic life, and mold compound • Arbitrary Waveform Generators (ARB)life. Such qualification testing should not be viewed as • Direct Digital Synthesis (DDS)justifying use of this component beyond specifiedperformance and environmental limits. • Cable Modem Termination System (CMTS)
The DAC5662 is a monolithic, dual-channel 12-bit, high-speed digital-to-analog converter (DAC) with on-chipvoltage reference.
Operating with update rates of up to 200 MSPS, the DAC5662 offers exceptional dynamic performance, tightgain, and offset matching characteristics that make it suitable in either I/Q baseband or direct IF communicationapplications.
Each DAC has a high-impedance differential-current output, suitable for single-ended or differentialanalog-output configurations. External resistors allow scaling the full-scale output current for each DACseparately or together, typically between 2 mA and 20 mA. An accurate on-chip voltage reference is temperaturecompensated and delivers a stable 1.2-V reference voltage. Optionally, an external reference may be used.
The DAC5662 has two 12-bit parallel input ports with separate clocks and data latches. For flexibility, theDAC5662 also supports multiplexed data for each DAC on one port when operating in the interleaved mode.
The DAC5662 has been specifically designed for a differential transformer coupled output with a 50-Ω doublyterminated load. For a 20-mA full-scale output current a 4:1 impedance ratio (resulting in an output power of4 dBm) and 1:1 impedance ratio transformer (–2-dBm output power) are supported.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of TexasInstruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Copyright © 2006, Texas Instruments IncorporatedProducts conform to specifications per the terms of the TexasInstruments standard warranty. Production processing does notnecessarily include testing of all parameters.
www.ti.com
DESCRIPTION (CONTINUED)
DEMUX
DA[11:0]
DB[11:0]
MODE
GSET
Latch A
Latch B 12−b DAC
12−b DACIOUTA1
IOUTA2
IOUTB1
IOUTB2
1.2 V Reference
WRTB WRTA CLKB CLKA
BIASJ_A
BIASJ_B
EXTIO
DVDD DGND AVDD AGND
SLEEP
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
The DAC5662 is available in a 48-pin thin quad flat pack (TQFP). Pin compatibility between family membersprovides 12-bit (DAC5662) and 14-bit (DAC5672) resolution. Furthermore, the DAC5662 is pin compatible to theDAC2902 and AD9765 dual DACs. The device is characterized for operation over the military temperature rangeof –55°C to 125°C.
FUNCTIONAL BLOCK DIAGRAM
AVAILABLE OPTIONS
PACKAGED DEVICESTA 48-PIN TQFP
DAC5662MPFBREP–55°C to 125°C
DAC5662MPFBEP
2 Submit Documentation Feedback
www.ti.com
DEVICE INFORMATION
13 14 15
NCNCDB0 (LSB)DB1DB2DB3DB4DB5DB6DB7DB8DB9
36
35
34
33
32
31
30
29
28
27
26
2516
1
2
3
4
5
6
7
8
9
10
11
12
DA11 (MSB)DA10
DA9DA8DA7DA6DA5DA4DA3DA2DA1
DA0 (LSB)17 18 19 20
AG
ND
47 46 45 44 4348 42
IOU
TA1
IOU
TA2
BIA
SJ_
AE
XT
IOG
SE
TB
IAS
J_B
IOU
TB
2D
VD
DD
B11
(M
SB
)D
B10
DG
ND
DV
DD
WR
TA/W
RT
IQC
LKA
/CLK
IQC
LKB
/RE
SE
TIQ
WR
TB
/SE
LEC
TIQ
DG
ND
40 39 3841
21 22 23 24
37
NC
SLE
EP
IOU
TB
1
MO
DE
AV
DD
NC
Top View48-Pin TQFPPFB Package
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
3Submit Documentation Feedback
www.ti.com
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
DEVICE INFORMATION (continued)TERMINAL FUNCTIONS
TERMINALI/O DESCRIPTION
NAME NO.
AGND 38 I Analog ground
AVDD 47 I Analog supply voltage
BIASJ_A 44 O Full-scale output current bias for DACA
BIASJ_B 41 O Full-scale output current bias for DACB
CLKA/CLKIQ 18 I Clock input for DACA, CLKIQ in interleaved mode
CLKB/RESETIQ 19 I Clock input for DACB, RESETIQ in interleaved mode
DA[11:0] 1–12 I Data port A. DA11 is MSB and DA0 is LSB.
DB[11:0] 23–34 I Data port B. DB11 is MSB and DB0 is LSB.
DGND 15, 21 I Digital ground
DVDD 16, 22 I Digital supply voltage
EXTIO 43 I/O Internal reference output (bypass with 0.1 µF to AGND) or external reference input
GSET 42 I Gain-setting mode: H = 1 resistor, L = 2 resistors. Internal pullup
IOUTA1 46 O DACA current output. Full scale with all bits of DA high.
IOUTA2 45 O DACA complementary current output. Full scale with all bits of DA low.
IOUTB1 39 O DACB current output. Full scale with all bits of DB high.
IOUTB2 40 O DACB complementary current output. Full scale with all bits of DB low.
MODE 48 I Mode select: H = dual bus, L = interleaved. Internal pullup.
13, 14, 35,NC – No connection36
Sleep function control input: H = DAC in power-down mode, L = DAC in operating mode.SLEEP 37 I Internal pulldown.
WRTA/WRTIQ 17 I Input write signal for PORT A (WRTIQ in interleaving mode)
WRTB/SELECTIQ 20 I Input write signal for PORT B (SELECTIQ in interleaving mode)
4 Submit Documentation Feedback
www.ti.com
PFB PACKAGE THERMAL CHARACTERISTICS
0.1
1
10
100
1000
100 110 120 130 140 150 160
Electromigration Fail Mode
Wirebond V oiding Fail Mode
Continuous T J − C
Yea
rs E
stim
ated
Life
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
PARAMETER POWERPAD CONNECTED TO PCB THERMAL PLANE
Thermal resistance, junction to ambient 63.7°C/W
Thermal resistance, junction to case 19.6°C/W
Figure 1. DAC5662MPFB Operating Life Derating Chart
5Submit Documentation Feedback
www.ti.com
ABSOLUTE MAXIMUM RATINGS (1)
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
over operating free-air temperature range (unless otherwise noted)
UNIT
AVDD (2) –0.5 V to 4 VSupply voltage range
DVDD (3) –0.5 V to 4 V
Voltage between AGND and DGND –0.5 V to 0.5 V
Voltage between AVDD and DVDD –0.5 V to 0.5 V
DA[11:0] and DB[11:0] (3) –0.5 V to DVDD + 0.5 V
MODE, CLKA, CLKB, WRTA, WRTB (3) –0.5 V to DVDD + 0.5 VSupply voltage range
IOUTA1, IOUTA2, IOUTB1, IOUTB2 (2) –1 V to AVDD + 0.5 V
EXTIO, BIASJ_A, BIASJ_B, SLEEP (2) –0.5 V to AVDD + 0.5 V
Peak input current (any input) 20 mA
Peak total input current (all inputs) –30 mA
Operating free-air temperature range –55°C to 125°C
Storage temperature range –65°C to 150°C
Lead temperature 1,6 mm (1/16 in) from the case for 10 s 260°C
(1) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratingsonly and functional operation of these or any other conditions beyond those indicated under “recommended operating conditions” is notimplied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) Measured with respect to AGND(3) Measured with respect to DGND
6 Submit Documentation Feedback
www.ti.com
ELECTRICAL CHARACTERISTICS
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
over operating free-air temperature range, AVDD = DVDD = 3.3 V, IOUTFS = 20 mA, independent gain set mode(unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
DC Specifications
Resolution 12 Bits
DC Accuracy (1)
INL Integral nonlinearity 1 LSB = IOUTFS/212, TA = 25°C –2 0.3 2 LSB
DNL Differential nonlinearity 1 LSB = IOUTFS/212, TA = 25°C –2 0.2 2 LSB
Analog Output
Offset error 0.03 %FSR
With external reference 0.25 %FSRGain error
With internal reference 0.5 %FSR
Minimum full-scale output current (2) 2 mA
Maximum full-scale output current (2) 20 mA
Gain mismatch With internal reference –2 0.07 2 %FSR
Output voltage compliance range (3) –0.8 1.25 V
RO Output resistance 300 kΩ
CO Output capacitance 5 pF
Reference Output
Reference voltage 1.14 1.2 1.26 V
Reference output current (4) 100 nA
Reference Input
VEXTIO Input voltage 0.1 1.25 V
RI Input resistance 1 MΩ
Small signal bandwidth 300 kHz
CI Input capacitance 100 pF
Temperature Coefficients
ppm ofOffset drift 0 FSR/°C
With external reference ±50 ppm ofGain drift FSR/°CWith internal reference ±50
Reference voltage drift ±20 ppm/°C
(1) Measured differentially through 50 Ω to AGND.(2) Nominal full-scale current, IOUTFS, equals 32× the IBIAS current.(3) The lower limit of the output compliance is determined by the CMOS process. Exceeding this limit may result in transistor breakdown,
resulting in reduced reliability of the DAC5662 device. The upper limit of the output compliance is determined by the load resistors andfull-scale output current. Exceeding the upper limit adversely affects distortion performance and intergral nonlinearity.
(4) Use an external buffer amplifier with high impedance input to drive any external load.
7Submit Documentation Feedback
www.ti.com
ELECTRICAL CHARACTERISTICS
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
over operating free-air temperature range, AVDD = DVDD = 3.3 V, IOUTFS = 20 mA, fDATA = 200 MSPS, fOUT = 1 MHz,independent gain set mode (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Power Supply
AVDD Analog supply voltage 3 3.3 3.6 V
DVDD Digital supply voltage 3 3.3 3.6 V
Including output current through load resistor 75 90
IAVDD Supply current, analog Sleep mode with clock 2.5 6 mA
Sleep mode without clock 2.5
25 38
IDVDD Supply current, digital Sleep mode with clock 12.5 18 mA
Sleep mode without clock <10
330 390
Power dissipation Sleep mode without clock 15 mW
fDATA = 200 MSPS, fOUT = 20 MHz 350
APSSR Analog power-supply rejection ratio –0.2 0.2 %FSR/V
DPSRR Digital power-supply rejection ratio –0.2 0.2 %FSR/V
TA Operating free-air temperature –55 125 °C
8 Submit Documentation Feedback
www.ti.com
ELECTRICAL CHARACTERISTICS
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
AC specifications over operating free-air temperature range, AVDD = DVDD = 3.3 V, IOUTFS = 20 mA, independent gain setmode, differential 1:1 impedance ratio transformer coupled output, 50-Ω doubly terminated load (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Analog Output
fclk Maximum output update rate 200 275 (1) MSPS
Output settling time to 0.1%ts Mid-scale transition 20 ns(DAC)
Output rise time 10% to 90%tr 1.4 ns(OUT)
Output fall time 90% to 10%tf 1.5 ns(OUT)
IOUTFS = 20 mA 55Output noise pA/√Hz
IOUTFS = 2 mA 30
AC Linearity
1st Nyquist zone, TA = 25°C, fDATA = 50 MSPS, 81fOUT = 1 MHz, IOUTFS = 0 dB
1st Nyquist zone, TA = 25 C, fDATA = 50 MSPS, 83fOUT = 1 MHz, IOUTFS = –6 dB
1st Nyquist zone, TA = 25°C, fDATA = 50 MSPS, 81fOUT = 1 MHz, IOUTFS = –12 dB
1st Nyquist zone, TA = 25°C, fDATA = 100 MSPS, 85fOUT = 5 MHzSFDR Spurious-free dynamic range dBc
1st Nyquist zone, TA = 25°C, fDATA = 100 MSPS, 78fOUT = 20 MHz
1st Nyquist zone, TA = 25°C, fDATA = 200 MSPS, 66 71fOUT = 20 MHz
1st Nyquist zone, Tmin = –55°C to 125°C, 63 71fDATA = 200 MSPS, fOUT = 20 MHz
1st Nyquist zone, TA = 25°C, fDATA = 200 MSPS, 68fOUT = 41 MHz
1st Nyquist zone, TA = 25°C, fDATA = 100 MSPS, 73fOUT = 5 MHzSNR Signal-to-noise ratio dB
1st Nyquist zone, TA = 25°C, fDATA = 200 MSPS, 67fOUT = 20 MHz
W-CDMA signal with 3.84-MHz bandwidth, 70fDATA = 61.44 MSPS, IF = 15.36 MHzACLR Adjacent channel leakage ratio dB
W-CDMA signal with 3.84-MHz bandwidth, 70fDATA = 122.88 MSPS, IF = 30.72 MHz
Each tone at –6 dBFS, TA = 25°C, fDATA = 200 MSPS, 62fOUT = 45.4 MHz and 46.4 MHzThird-order two-toneIMD3 dBcintermodulation Each tone at –6 dBFS, TA = 25°C, fDATA = 100 MSPS, 78fOUT = 15.1 MHz and 16.1 MHz
Each tone at –12 dBFS, TA = 25°C, fDATA = 100 MSPS, 77fOUT = 15.6, 15.8, 16.2, and 16.4 MHz
Each tone at –12 dBFS, TA = 25°C, fDATA = 165 MSPS,IMD Four-tone intermodulation 56 dBcfOUT = 68.8, 69.6, 71.2, and 72 MHz
Each tone at –12 dBFS, TA = 25°C, fDATA = 165 MSPS, 74fOUT = 19.0, 19.1, 19.3, and 19.4 MHz
TA = 25°C, fDATA = 165 MSPS, fOUT (CH1) = 20 MHz,Channel isolation 97 dBcfOUT (CH2) = 21 MHz
(1) Specified by design. Not production tested.
9Submit Documentation Feedback
www.ti.com
ELECTRICAL CHARACTERISTICS
SWITCHING CHARACTERISTICS
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
Digital specifications over operating free-air temperature range, AVDD = DVDD = 3.3 V, IOUTFS = 20 mA(unless otherwise noted)
PARAMETER MIN TYP MAX UNIT
Digital Input
VIH High-level input voltage 2 3.3 V
VIL Low-level input voltage 0 0.8 V
IIH High-level input current 50 µA
IIL Low-level input current 10 µA
IIH(GSET) High-level input current, GSET pin 7 µA
IIL(GSET) Low-level input current, GSET pin –30 µA
IIH(MODE) High-level input current, MODE pin –30 µA
IIL(MODE) Low-level input current, MODE pin –80 µA
CI Input capacitance 5 pF
Digital specifications over operating free-air temperature range, AVDD = DVDD = 3.3 V, IOUTFS = 20 mA(unless otherwise noted)
PARAMETER MIN TYP MAX UNIT
Timing – Dual Bus Mode
tsu Input setup time 1 ns
th Input hold time 1 ns
tLPH Input clock pulse high time 2 ns
tLAT Clock latency (WRTA/B to outputs) (1) 4 4 clk
tPD Propagation delay time 1.5 ns
Timing – Single Bus Interleaved Mode
tsu Input setup time 0.5 ns
th Input hold time 0.5 ns
tLAT Clock latency (WRTA/B to outputs) (1) 4 4 clk
tPD Propagation delay time 1.5 ns
(1) Specified by design
10 Submit Documentation Feedback
www.ti.com
TYPICAL CHARACTERISTICS
−0.4
−0.3
−0.2
−0.1
0.0
0.1
0.2
0.3
0.4
0 512 1024 1536 2048 2560 3072 3584 4096
Input Code
INL
– In
tegr
al N
onlin
earit
y E
rror
– L
SB
G001
INTEGRAL NONLINEARITYvs
INPUT CODE
−0.20
−0.15
−0.10
−0.05
0.00
0.05
0.10
0.15
0.20
0 512 1024 1536 2048 2560 3072 3584 4096
Input Code
DN
L –
Diff
eren
tial N
onlin
earit
y E
rror
– L
SB
G002
DIFFERENTIAL NONLINEARITYvs
INPUT CODE
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
Figure 2.
Figure 3.
11Submit Documentation Feedback
www.ti.com
60
65
70
75
80
85
90
95
100
0 4 8 12 16 20 24
fO − Output Frequency − MHz
fdata = 52 MSPSDual Bus ModeS
FD
R −
Spu
rious
-Fre
e D
ynam
ic R
ange
− d
Bc
0 dBf S
−12 dBf S
−6 dBf S
G003
60
65
70
75
80
85
90
95
100
0 5 10 15 20 25 30 35
fO − Output Frequency − MHz
fdata = 78 MSPSDual Bus ModeS
FD
R −
Spu
rious
-Fre
e D
ynam
ic R
ange
− d
Bc
−12 dBf S
−6 dBf S
G004
0 dBf S
60
65
70
75
80
85
90
95
100
0 5 10 15 20 25 30 35 40
fO − Output Frequency − MHz
fdata = 100 MSPSDual Bus ModeS
FD
R −
Spu
rious
-Fre
e D
ynam
ic R
ange
− d
Bc
−12 dBf S
G005
0 dBf S
−6 dBf S
60
65
70
75
80
85
90
95
100
0 5 10 15 20 25 30 35 40 45 50 55 60 65
fO − Output Frequency − MHz
fdata = 165 MSPSDual Bus ModeS
FD
R −
Spu
rious
-Fre
e D
ynam
ic R
ange
− d
Bc
−12 dBf S
G006
0 dBf S
−6 dBf S
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
TYPICAL CHARACTERISTICS (continued)
SPURIOUS-FREE DYNAMIC RANGE SPURIOUS-FREE DYNAMIC RANGEvs vs
OUTPUT FREQUENCY OUTPUT FREQUENCY
Figure 4. Figure 5.
SPURIOUS-FREE DYNAMIC RANGE SPURIOUS-FREE DYNAMIC RANGEvs vs
OUTPUT FREQUENCY OUTPUT FREQUENCY
Figure 6. Figure 7.
12 Submit Documentation Feedback
www.ti.com
f - Frequency - MHz
-100
-80
-60
-40
-20
0
0.0 7.8 15.6 23.4 31.2 39.0
fdata = 78 MSPSfOUT = 15 MHzDual Bus Mode
Po
wer
- d
Bm
G007f − Frequency − MHz
−100
−80
−60
−40
−20
0
0.0 16.5 33.0 49.5 66.0 82.5
fdata = 165 MSPSfOUT = 30.1 MHzDual Bus Mode
Pow
er −
dB
m
G008
fO − Output Frequency − MHz
60
65
70
75
80
85
90
95
0 5 10 15 20 25 30 35
Two-
Ton
e IM
D3
− dB
c
fdata = 78 MSPSDual Bus Mode
G009fO − Output Frequency − MHz
50
55
60
65
70
75
80
85
90
95
100
0 10 20 30 40 50
Two-
Ton
e IM
D3
− dB
c
fdata = 165 MSPSDual Bus Mode
G010
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
TYPICAL CHARACTERISTICS (continued)
SINGLE-TONE SPECTRUM SINGLE-TONE SPECTRUM
Figure 8. Figure 9.
TWO-TONE IMD3 TWO-TONE IMD3vs vs
OUTPUT FREQUENCY OUTPUT FREQUENCY
Figure 10. Figure 11.
13Submit Documentation Feedback
www.ti.com
f − Frequency − MHz
−100
−80
−60
−40
−20
0
19.0 19.5 20.0 20.5 21.0 21.5 22.0
Pow
er −
dB
m
G011
fdata = 78 MSPSfOUT = 20.1 MHzand 21.1 MHzDual Bus Mode
f − Frequency − MHz
−100
−80
−60
−40
−20
0
29.0 29.5 30.0 30.5 31.0 31.5 32.0P
ower
− d
Bm
G012
fdata = 165 MSPSfOUT = 30.1 MHzand 31.1 MhzDual Bus Mode
f − Frequency − MHz
−120
−100
−80
−60
−40
−20
0 1 2 3 4 5 6 7 8 9 10
fdata = 122.88 MSPSBaseband SignalACPR = 72 dBDual Bus Mode
Pow
er −
dB
m
G013f − Frequency − MHz
Pow
er −
dB
m
G014
−120
−100
−80
−60
−40
−20
18 20 22 24 26 28 30 32 34 36 38 40 42 44
fdata = 122.88 MSPSIF = 30.72 MHzACPR = 72 dBDual Bus Mode
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
TYPICAL CHARACTERISTICS (continued)
TWO-TONE SPECTRUM TWO-TONE SPECTRUM
Figure 12. Figure 13.
POWER POWERvs vs
FREQUENCY FREQUENCY
Figure 14. Figure 15.
14 Submit Documentation Feedback
www.ti.com
DIGITAL INPUTS AND TIMING
Digital Inputs
DA[11:0]DB[11:0]
SLEEPCLKA/BWRTA/B
InternalDigital In
DVDD
DGND
GSETMODE
InternalDigital In
DVDD
DGND
Input Interfaces
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
The data input ports of the DAC5662 accept a standard positive coding with data bit D11 being the mostsignificant bit (MSB). The converter outputs are specified to support a clock rate up to 200 MSPS. The bestperformance is typically be achieved with a symmetric duty cycle for write and clock; however, the duty cyclemay vary as long as the timing specifications are met. Similarly, the setup and hold times may be chosen withintheir specified limits.
All digital inputs of the DAC5662 are CMOS compatible. Figure 16 and Figure 17 show schematics of theequivalent CMOS digital inputs of the DAC5662. The 12-bit digital data input follows the offset positive binarycoding scheme. The DAC5662 is designed to operate with a digital supply (DVDD) of 3 V to 3.6 V.
Figure 16. CMOS/TTL Digital Equivalent Input With Internal Pulldown Resistor
Figure 17. CMOS/TTL Digital Equivalent Input With Internal Pullup Resistor
The DAC5662 features two operating modes selected by the MODE pin (see Table 1).• For dual-bus input mode, the device essentially consists of two separate DACs. Each DAC has its own
separate data input bus, clock input, and data write signal (data latch-in).• In single-bus interleaved mode, the data should be presented interleaved at the I-channel input bus. The
Q-channel input bus is not used in this mode. The clock and write input are now shared by both DACs.
Table 1. Operating Modes
MODE PIN Mode pin connected to DGND Mode pin connected to DVDD
BUS INPUT Single-bus interleaved mode, clock and write input equal for both DACs Dual-bus mode, DACs operate independently
15Submit Documentation Feedback
www.ti.com
DIGITAL INPUTS AND TIMING (continued)
Dual-Bus Data Interface and Timing
Valid DataD[11:0]
tsu th
tLAT tpd
tsettle
WRT1/WRT2
CLK1/CLK2
IOUTor
IOUT
t1PH
Single-Bus Interleaved Data Interface and Timing
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
In dual-bus mode, the MODE pin is connected to DVDD. The two converter channels within the DAC5662consist of two independent, 12-bit, parallel data ports. Each DAC channel is controlled by its own set of write(WRTA, WRTB) and clock (CLKA, CLKB) lines. The WRT lines control the channel input latches and the CLKlines control the DAC latches. The data is first loaded into the input latch by a rising edge of the WRT line
The internal data transfer requires a correct sequence of write and clock inputs, since essentially two clockdomains having equal periods (but possibly different phases) are input to the DAC5662. This is defined by aminimum requirement of the time between the rising edge of the clock and the rising edge of the write inputs.This essentially implies that the rising edge of CLK must occur at the same time or before the rising edge of theWRT signal. A minimum delay of 2 ns should be maintained if the rising edge of the clock occurs after the risingedge of the write. Note that these conditions are satisfied when the clock and write inputs are connectedexternally. Note that all specifications were measured with the WRT and CLK lines connected together.
Figure 18. Dual-Bus-Mode Operation
In single-bus interleaved mode, the MODE pin is connected to DGND. Figure 19 shows the timing diagram. Ininterleaved mode, the I and Q channels share the write input (WRTIQ) and update clock (CLKIQ and internalCLKDACIQ). Multiplexing logic directs the input word at the I-channel input bus to either the I-channel input latch(SELECTIQ is high) or to the Q-channel input latch (SELECTIQ is low). When SELECTIQ is high, the data valuein the Q-channel latch is retained by presenting the latch output data to its input again. When SELECTIQ is low,the data value in the I-channel latch is retained by presenting the latch output data to its input.
In interleaved mode, the I-channel input data rate is twice the update rate of the DAC core. As in dual-bus mode,it is important to maintain a correct sequence of write and clock inputs. The edge-triggered flip-flops latch the I-and Q-channel input words on the rising edge of the write input (WRTIQ). This data is presented to the I- andQ-DAC latches on the following falling edge of the write inputs. The DAC5662 clock input is divided by a factorof two before it is presented to the DAC latches.
Correct pairing of the I- and Q-channel data is done by RESETIQ. In interleaved mode, the clock input CLKIQ isdivided by two, which would translate to a nondeterministic relation between the rising edges of the CLKIQ andCLKDACIQ. RESETIQ ensures, however, that the correct position of the rising edge of CLKDACIQ, with respectto the data at the input of the DAC latch, is determined. CLKDACIQ is disabled (low) when RESETIQ is high.
16 Submit Documentation Feedback
www.ti.com
DIGITAL INPUTS AND TIMING (continued)
Valid DataD[11:0]
tsu th
tLAT tpd
tsettle
SELECTIQ
WRTIQ
CLKIQ
RESETIQ
IOUTor
IOUT
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
Figure 19. Single-Bus Interleaved-Mode Operation
17Submit Documentation Feedback
www.ti.com
APPLICATION INFORMATION
Theory of Operation
DAC Transfer Function
IOUTFS IOUT1 IOUT2 (1)
IOUT1 IOUTFS Code4096
(2)
IOUT2 IOUTFS 4095 Code4096
(3)
IOUTFS 32 IREF 32VREFRSET (4)
VOUT1 IOUT1 RLOAD (5)VOUT2 IOUT2 RLOAD (6)
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
The architecture of the DAC5662 uses a current steering technique to enable fast switching and high updaterate. The core element within the monolithic DAC is an array of segmented current sources that are designed todeliver a full-scale output current of up to 20 mA. An internal decoder addresses the differential current switcheseach time the DAC is updated and a corresponding output current is formed by steering all currents to eitheroutput summing node, IOUT1 and IOUT2. The complementary outputs deliver a differential output signal, whichimproves the dynamic performance through reduction of even-order harmonics, common-mode signals (noise),and double the peak-to-peak output signal swing by a factor of two, compared to single-ended operation.
The segmented architecture results in a significant reduction of the glitch energy and improves the dynamicperformance (SFDR) and DNL. The current outputs maintain a high output impedance of greater than 300 kΩ.
When pin 42 (GSET) is high (one resistor mode), the full-scale output current for both DACs is determined bythe ratio of the internal reference voltage (1.2 V) and an external resistor (RSET) connected to BIASJ_A. WhenGSET is low (two resistor mode), the full-scale output current for each DACs is determined by the ratio of theinternal reference voltage (1.2 V) and separate external resistors (RSET) connected to BIASJ_A and BIASJ_B.The resulting IREF is internally multiplied by a factor of 32 to produce an effective DAC output current that canrange from 2 mA to 20 mA, depending on the value of RSET.
The DAC5662 is split into a digital and an analog portion, each of which is powered through its own supply pin.The digital section includes edge-triggered input latches and the decoder logic, while the analog sectioncomprises the current source array with its associated switches, and the reference circuitry.
Each of the DACs in the DAC5662 has a set of complementary current outputs, IOUT1 and IOUT2. The full-scaleoutput current, IOUTFS, is the summation of the two complementary output currents:
The individual output currents depend on the DAC code and can be expressed as:
where Code is the decimal representation of the DAC data input word. Additionally, IOUTFS is a function of thereference current IREF, which is determined by the reference voltage and the external setting resistor (RSET).
In most cases, the complementary outputs drive resistive loads or a terminated transformer. A signal voltagedevelops at each output according to:
The value of the load resistance is limited by the output compliance specification of the DAC5662. To maintainspecified linearity performance, the voltage for IOUT1 and IOUT2 should not exceed the maximum allowablecompliance range.
18 Submit Documentation Feedback
www.ti.com
VOUTDIFF VOUT1 VOUT2 (7)
VOUTDIFF (2 Code 4095)
4096 IOUTFS RLOAD (8)
Analog Outputs
AVDD
Current Source Array
S(1) S(1)C
RLOAD RLOAD
S(2) S(2)C S(N) S(N)C
IOUT2IOUT1
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
APPLICATION INFORMATION (continued)
The total differential output voltage is:
The DAC5662 provides two complementary current outputs, IOUT1 and IOUT2. The simplified circuit of the analogoutput stage representing the differential topology is shown in Figure 20. The output impedance of IOUT1 andIOUT2 results from the parallel combination of the differential switches, along with the current sources andassociated parasitic capacitances.
Figure 20. Analog Outputs
The signal voltage swing that may develop at the two outputs, IOUT1 and IOUT2, is limited by a negative andpositive compliance. The negative limit of –1 V is given by the breakdown voltage of the CMOS process andexceeding it compromises the reliability of the DAC5662 or even causes permanent damage. With the full-scaleoutput set to 20 mA, the positive compliance equals 1.2 V. Note that the compliance range decreases to about1 V for a selected output current of IOUTFS = 2 mA. Care should be taken that the configuration of DAC5662 doesnot exceed the compliance range to avoid degradation of the distortion performance and integral linearity.
Best distortion performance is typically achieved with the maximum full-scale output signal limited toapproximately 0.5 VPP. This is the case for a 50-Ω doubly terminated load and a 20-mA full-scale output current.A variety of loads can be adapted to the output of the DAC5662 by selecting a suitable transformer whilemaintaining optimum voltage levels at IOUT1 and IOUT2. Furthermore, using the differential output configuration incombination with a transformer is instrumental for achieving excellent distortion performance. Common-modeerrors, such as even-order harmonics or noise, can be substantially reduced. This is particularly the case withhigh output frequencies.
For those applications requiring the optimum distortion and noise performance, it is recommended to select afull-scale output of 20 mA. A lower full-scale range of 2 mA may be considered for applications that require lowpower consumption, but can tolerate a slight reduction in performance level.
19Submit Documentation Feedback
www.ti.com
Output Configurations
Differential With Transformer
1:1
50 Ω
50 Ω
RLOAD50 Ω100 Ω AGND
IOUT2
IOUT1
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
APPLICATION INFORMATION (continued)
The current outputs of the DAC5662 allow for a variety of configurations. As mentioned previously, utilizing theconverter’s differential outputs yield the best dynamic performance. Such a differential output circuit may consistof an RF transformer or a differential amplifier configuration. The transformer configuration is ideal for mostapplications with ac coupling, while operational amplifiers are suitable for a dc-coupled configuration.
The single-ended configuration may be considered for applications requiring a unipolar output voltage.Connecting a resistor from either one of the outputs to ground converts the output current into aground-referenced voltage signal. To improve on the dc linearity by maintaining a virtual ground, an I-to-V oroperational amplifier configuration may be considered.
Using an RF transformer provides a convenient way of converting the differential output signal into asingle-ended signal while achieving excellent dynamic performance. The appropriate transformer should becarefully selected based on the output frequency spectrum and impedance requirements.
The differential transformer configuration has the benefit of significantly reducing common-mode signals, thusimproving the dynamic performance over a wide range of frequencies. Furthermore, by selecting a suitableimpedance ratio (winding ratio), the transformer can be used to provide optimum impedance matching whilecontrolling the compliance voltage for the converter outputs.
Figure 21 and Figure 22 show 50-Ω doubly terminated transformer configurations with 1:1 and 4:1 impedanceratios, respectively. Note that the center tap of the primary input of the transformer has to be grounded to enablea dc-current flow. Applying a 20-mA full-scale output current leads to a 0.5-VPP output for a 1:1 transformer anda 1-VPP output for a 4:1 transformer. In general, the 1:1 transformer configuration has slightly better outputdistortion, but the 4:1 transformer has 6-dB higher output power.
Figure 21. Driving a Doubly-Terminated 50-Ω Cable Using a 1:1 Impedance Ratio Transformer
20 Submit Documentation Feedback
www.ti.com
4:1
100 Ω
100 Ω
RLOAD50 Ω
AGND
IOUT2
IOUT1
Single-Ended Configuration
50 Ω25 Ω
RLOAD50 Ω
AGND
IOUT2
IOUT1
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
APPLICATION INFORMATION (continued)
Figure 22. Driving a Doubly-Terminated 50-Ω Cable Using a 4:1 Impedance Ratio Transformer
Figure 23 shows the single-ended output configuration, where the output current IOUT1 flows into an equivalentload resistance of 25 Ω. Node IOUT2 should be connected to AGND or terminated with a resistor of 25 Ω toAGND. The nominal resistor load of 25 Ω gives a differential output swing of 1 VPP when applying a 20-mAfull-scale output current.
Figure 23. Driving a Doubly-Terminated 50-Ω Cable Using a Single-Ended Output
21Submit Documentation Feedback
www.ti.com
Reference Operation
Internal Reference
IOUTFS 32 IREF 32VREFRSET (9)
External Reference
Gain Setting Option
Sleep Mode
DAC5662-EP
SGLS340A–JUNE 2006–REVISED OCTOBER 2006
APPLICATION INFORMATION (continued)
The DAC5662 has an on-chip reference circuit which comprises a 1.2-V bandgap reference and two controlamplifiers, one for each DAC. The full-scale output current, IOUTFS, of the DAC5662 is determined by thereference voltage, VREF, and the value of resistor RSET. IOUTFS can be calculated by:
The reference control amplifier operates as a V-to-I converter producing a reference current, IREF, which isdetermined by the ratio of VREF and RSET (see Equation 9). The full-scale output current, IOUTFS, results frommultiplying IREF by a fixed factor of 32.
Using the internal reference, a 2-kΩ resistor value results in a full-scale output of approximately 20 mA.Resistors with a tolerance of 1% or better should be considered. Selecting higher values, the output current canbe adjusted from 20 mA down to 2 mA. Operating the DAC5662 at lower than 20-mA output currents may bedesirable for reasons of reducing the total power consumption, improving the distortion performance, orobserving the output compliance voltage limitations for a given load condition.
It is recommended to bypass the EXTIO pin with a ceramic chip capacitor of 0.1 µF or more. The controlamplifier is internally compensated and its small signal bandwidth is approximately 300 kHz.
The internal reference can be disabled by simply applying an external reference voltage into the EXTIO pin that,in this case, functions as an input. The use of an external reference may be considered for applications thatrequire higher accuracy and drift performance or to add the ability of dynamic gain control.
While a 0.1-µF capacitor is recommended to be used with the internal reference, it is optional for the externalreference operation. The reference input, EXTIO, has a high input impedance (1 MΩ) and can easily be drivenby various sources. Note that the voltage range of the external reference should stay within the compliancerange of the reference input.
The full-scale output current on the DAC5662 can be set two ways — either for each of the two DAC channelsindependently or for both channels simultaneously. For the independent gain set mode, the GSET pin (pin 42)must be low (that is, connected to AGND). In this mode, two external resistors are required — one RSETconnected to the BIASJ_A pin (pin 44) and the other to the BIASJ_B pin (pin 41). In this configuration, the userhas the flexibility to set and adjust the full-scale output current for each DAC independently, allowing for thecompensation of possible gain mismatches elsewhere within the transmit signal path.
Alternatively, bringing the GSET pin high (that is, connected to AVDD), the DAC5662 switches into thesimultaneous gain set mode. Now the full-scale output current of both DAC channels is determined by only oneexternal RSET resistor connected to the BIASJ_A pin. The resistor at the BIASJ_2 pin may be removed;however, this is not required since this pin is not functional in this mode and the resistor has no effect on thegain equation.
The DAC5662 features a power-down function that can be used to reduce the total supply current to less than3.5 mA over the specified supply range if no clock is present. Applying a logic high to the SLEEP pin initiates thepower-down mode, while a logic low enables normal operation. When left unconnected, an internal activepulldown circuit enables the normal operation of the converter.
22 Submit Documentation Feedback
PACKAGE OPTION ADDENDUM
www.ti.com 31-May-2014
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status(1)
Package Type PackageDrawing
Pins PackageQty
Eco Plan(2)
Lead/Ball Finish(6)
MSL Peak Temp(3)
Op Temp (°C) Device Marking(4/5)
Samples
DAC5662MPFBEP ACTIVE TQFP PFB 48 250 Green (RoHS& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR -55 to 125 DAC5662EP
DAC5662MPFBREP ACTIVE TQFP PFB 48 1000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR -55 to 125 DAC5662EP
V62/06651-01XE ACTIVE TQFP PFB 48 1000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR -55 to 125 DAC5662EP
V62/06651-02XE ACTIVE TQFP PFB 48 250 Green (RoHS& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR -55 to 125 DAC5662EP
(1) The marketing status values are defined as follows:ACTIVE: Product device recommended for new designs.LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.PREVIEW: Device has been announced but is not in production. Samples may or may not be available.OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availabilityinformation and additional product content details.TBD: The Pb-Free/Green conversion plan has not been defined.Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement thatlead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used betweenthe die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weightin homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuationof the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finishvalue exceeds the maximum column width.
PACKAGE OPTION ADDENDUM
www.ti.com 31-May-2014
Addendum-Page 2
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on informationprovided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken andcontinues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF DAC5662-EP :
• Catalog: DAC5662
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device PackageType
PackageDrawing
Pins SPQ ReelDiameter
(mm)
ReelWidth
W1 (mm)
A0(mm)
B0(mm)
K0(mm)
P1(mm)
W(mm)
Pin1Quadrant
DAC5662MPFBREP TQFP PFB 48 1000 330.0 16.4 9.6 9.6 1.5 12.0 16.0 Q2
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
DAC5662MPFBREP TQFP PFB 48 1000 367.0 367.0 38.0
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 2
MECHANICAL DATA
MTQF019A – JANUARY 1995 – REVISED JANUARY 1998
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PFB (S-PQFP-G48) PLASTIC QUAD FLATPACK
4073176/B 10/96
Gage Plane
0,13 NOM
0,25
0,450,75
Seating Plane
0,05 MIN
0,170,27
24
25
13
12
SQ
36
37
7,206,80
48
1
5,50 TYP
SQ8,809,20
1,050,95
1,20 MAX0,08
0,50 M0,08
0°–7°
NOTES: A. All linear dimensions are in millimeters.B. This drawing is subject to change without notice.C. Falls within JEDEC MS-026
IMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and otherchanges to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latestissue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current andcomplete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of salesupplied at the time of order acknowledgment.TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s termsand conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessaryto support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarilyperformed.TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products andapplications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provideadequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, orother intellectual property right relating to any combination, machine, or process in which TI components or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty orendorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of thethird party, or a license from TI under the patents or other intellectual property of TI.Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alterationand is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altereddocumentation. Information of third parties may be subject to additional restrictions.Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or servicevoids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirementsconcerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or supportthat may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards whichanticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might causeharm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the useof any TI components in safety-critical applications.In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is tohelp enable customers to design and create their own end-product solutions that meet applicable functional safety standards andrequirements. Nonetheless, such components are subject to these terms.No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the partieshave executed a special agreement specifically governing such use.Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use inmilitary/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI componentswhich have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal andregulatory requirements in connection with such use.TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use ofnon-designated products, TI will not be responsible for any failure to meet ISO/TS16949.Products ApplicationsAudio www.ti.com/audio Automotive and Transportation www.ti.com/automotiveAmplifiers amplifier.ti.com Communications and Telecom www.ti.com/communicationsData Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computersDLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-appsDSP dsp.ti.com Energy and Lighting www.ti.com/energyClocks and Timers www.ti.com/clocks Industrial www.ti.com/industrialInterface interface.ti.com Medical www.ti.com/medicalLogic logic.ti.com Security www.ti.com/securityPower Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defenseMicrocontrollers microcontroller.ti.com Video and Imaging www.ti.com/videoRFID www.ti-rfid.comOMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.comWireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2014, Texas Instruments Incorporated