CY4531 EZ-PDTM CCG3 EVK

QUICK START GUIDE

STEP

2

Verify that the user LED jumper (J11) is populated on the CCG EVK base board. Verify that the VSYSselection jumper (J3) on the CCG3 daughter card is set to 3.3 V (position 1-2) and the IO Supplyselection jumper (J4) is set to VDDD (position 2-3). Connect the DC power adapter (provided withthe kit) to the DC power jack (J1) of the CCG base board. Plug the other end of the DC poweradapter into an AC power socket. LED1 (Green) on the CCG3 daughter card and the CCG EVK baseboard turn ON to indicate that the kit is powered. In addition, LED2 (Orange) on the CCG EVK baseboard blinks continuously to indicate that CCG �rmware is executing.

J4 DisplayPort Connector

J12 Variable Power Supply(Provider) Header

J7 Consumer Power Output Header

J7 USB 2.0 Mini-B Receptacle

J4 IO Supply Selection Jumper2-3 Short: Power from VDDD of CCG3 (Default Setting)

J3 VSYS Selection Jumper1-2 Short: 3.3V supply coming fromCCG base board (Default Setting)

J2 USB 3.0 Type-B Receptacle

J3 USB Type-C Receptacle

LED1 CCG EVK Base Board

LED2 CCG EVK Base Board

J1 24V DC Power Supply (Provider) Connector

J9 Debug Connector

Reset Switch

CYPD3125-40LQXITLED1 CY4531 CCG3 Daughter Card

J11 LED Jumper

CCG EVKBase Board

CY4531 CCG3Daughter Card

USB 2.0 Type-A to Mini-B Cable

USB 3.1 EMCAType-C Cable

USB 3.0 Type-Ato Type-B Cable

24V DC Power AdapterUSB Type-C toType-A Adapter

STEP

1

Unpack the kit contents

CY4531 EZ-PDTM CCG3 EVK

QUICK START GUIDE

STEP

3

Connect the USB 3.0 Type-A to Type-B cable from the PC to the USB Type-B receptacle (J2) of the CCG base board. Connect the USB Type-C to Type-A adapter to the USB Type-C receptacle (J3) of the CCG base board. Plug a USB �ash drive (not provided with the kit) into the USB Type-C to Type-A adapter.Verify your setup as shown in the picture below. Observe the enumeration of the USB �ash drive on the PC. Initiate data transfer between the PC and the �ash drive, and observe the data transfer speed*.

STEP

4

For more details, refer to the CY4531 Kit Guide.pdf** located atC:\Program Files (x86)\Cypress\CY4531 CCG3 EVK\1.0\Documentation on 64-bit Windowsoperating systems or C:\Program Files\Cypress\CY4531 CCG3 EVK\1.0\Documentation on32-bit Windows operating systems.

** Download and install the CY4531 CCG3 EVK setup �le from www.cypress.com/CY4531 to access the latest kit design �les and documentation

Note that any USB device can be used instead of a �ash drive with the setup shown in step 3.

* Data transfer speed depends on the type of the USB port (SuperSpeed or High Speed) of the PC, read/write speed of the �ash drive (SuperSpeed or High Speed) and the system con�guration. You can evaluate the reversibility of the Type-C interface by detaching the USB Type-C to Type-A adapter, reconnecting it in an upside-down orientation and observing its enumeration.

© 2016 Cypress Semiconductor Corporation. All rights reserved. All trademarks or registered trademarks referenced herein are the properties of their respective owners. 002-10220 Rev.*A

USB 3.0 Type-Ato Type-B cable

J2

USB Type-C to Type-A adapter

24 V DC from outputof power adapter

USB �ash drive

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information: Cypress Semiconductor:

  CY4531