PERSONAL INFORMATION

Name: Ahmed Hamdy ElMahdyMarital status: FinishedMobile: 00201006900796Email: Eng_ahmed_152@yahoo.comAddress 1: Giza- EgyptADDRESS 2: Aluminium city–Naga Hammady-Qena - Egypt

EDUCATION 

B.Sc. Metallurgical Engineering Science, Mining, petroleum, and Metallurgy Department - Faculty of Engineering - Cairo University - Egypt.

Graduation year: May 2011 General Grade: Good (66%) Graduation project: Extracting of Aluminum in aluminum cells Graduation project grade:very good

Related Courses:

Casting

Iron and steel industry

Metal forming [hot rolling,cold rolling and extrusion]

Structure and design of alloys

Physical metallurgy and Corrosion

Welding[consumable and non-consumable]arc welding

Destructive and non-destructive testing(penetration test, magnetic test, ultrasonic test and radio graphic test)

Extraction of non-ferrous metals [aluminum, tin and copper]

Jobobjectives

Seeking a challenging and creative job where I can make the best use of my interpersonal, communication and analysing skills. Preferring one of the following positions:

Mining Engineer

Inspection Engineer

Production Engineer

Maintenance Engineer

Mineral processing Engineer

Safety Engineer

Courses

NDT inspection for non-destructive testing and welding technology in EWA (Egyptian welding academy)

1. Applied welding technology

2. Liquid penetration test

3. Magnetic penetration test

4. Ultrasonic test

5. Radio graphic test

6. Visual inspection

With certificate

Work experiences

Egypt alum company for extraction of aluminium

Quality engineering group ( inspection,NDT service)

Training experience

The Aluminum Company of Egypt in Naga Hammady (Egypt alum).

18/8/2007 to 30/8/2007

1/7/2008 to 16/7/2008

1/8/2009 to 13/8/2009

13/1/2010 to 28/1/2010

Egyptian company of Egypt for steel (Al Ezzdekhela steel co.)

12/7/2009 to 23/7/2009

Familiar with the following QA/QC Scope: Documentation: - Preparing WPSs (Welding Procedure Specifications), PQRs (Procedure Qualification Records) and WPQs (Welder Performance Qualifications) & Check Specifications (Year and Revision) - Preparing Weld Map & ITP (Inspection & Test Plan) and Review Fabrication Drawings - Material Verifications as per Procurement Order (P.O.) and Reviewing of Mill Test Certificate (MTC) and MTRs/Lab Reports for traceability and conformance to mechanical /chemical properties in accordance with applicable Codes, Standards & Client Spec. Requirements - Validate Calibration Certificates of Welding Equipment & Inspection Instruments

Incoming Material Inspection: Dimensional & Visual Inspection and Lamination Test (if required) Welder Qualification: Witness Welder Qualification tests in association with approved WPS Inspection before Welding: - Check welding equipment and all related ancillaries (cables, regulators, ovens) - Check welding consumables for size, condition, specification and storage - Check layout/marking for cutting of materials - Check fit-up & preparation of the joints (relevant bevel angles, root face, root gap, etc.) as per the detailed drawing and WPS - Dimensional inspection & monitor all tack welding - Check method of preheat (if applicable) & pre-welding distortion control

Inspection during Welding: - Check amperage, voltage, polarity & travel Speed - Check welding technique & weld direction - Ensure qualified welders are performing welding efficiently and in the specified welding time - Ensure adequate inter pass cleaning & inter pass temperature

Inspection after Welding: - Check weld dimensions, contour & width - Carry out visual welding inspections & Ensure post weld cleaning (arc strikes, spatters) - Check PWHT (if applicable) and Review PWHT Charts & Specifications - Witness & Evaluation of Non Destructive Examinations and Destructive tests of weld samples - Mark up repair areas and Monitor & Control the welding repair - Checking of Sand Blasting & Inspection on Painting to meet required microns

Final Documentation: Review & Maintain Dimensional, NDT, Sand Blasting & Painting and Release to Site Reports Familiar with the following Codes & Standards: - ASME II Part A&C&D, ASME V, ASME IX, ASME B31.1, ASME B31.3 - AWS D1.1, AWS D1.5, AWS A2.4, AWS A3.0, EN-ISO 898-1, EN-ISO 898-2 - API 1104, API 5L, API 510, API 570, API 653

Computer Skills

Microsoft: MS DOS and Windows. Microsoft Office: Word, Excel. Internet.

ICDL UNESCOcertificate from South Valley University.

Languages

Arabic: native. English:Very good speaking and writing French:Fair knowledge.

InterpersonalSkills

Ability to learn and retain new knowledge quickly Working effectively with teamwork Highly adaptable, positive, resilient, patient risk-taker Willingness to work outside country of residence