CTM-100 Installation Instructions · PDF fileIdentify the correct plasma bracket mounting...
5
CTM-100 Installation Instructions Read and understand the installations carefully for a proper installation of the wall mount. Step 1 Invert the display and place it on a soft and flat surface. Locate the mounting points on the back of the plasma display. Identify the correct plasma bracket mounting hardware for your plasma display from the chart shown on the back of the assembly manual and secure the (L) Left and (R) Right hand side mounting brackets to the plasma using the corresponding hardware (supplied). Note : Make sure the upper “clevis” hook mounting screw, nut and reference arrow are facing to the left and right outside edges of the display. Step 2 Temporarily slide the round steel rod portion of one of the CTM plate fully into the bottom receiving slots of the installed plasma mounting brackets. Measure the distance between the bottom outside edge of the plasma display and the bottom outside edge of the wall mounting plate. Add the desired bottom edge height of the display to the distance between the bottom edge of the wall plate and the bottom edge of the display to determine the correct mounting height of the wall plate. Example: Overall desired height for the bottom outside of the display is 60". Difference between the bottom edge of the display and the bottom edge of the wall plate fully installed in the lower receiving slots of the brackets is 4" means the wall plate bottom outside edge should be placed at 64" from the floor (60" + 4" = 64"). Determine the desired wall location and its ability to properly support the weight of the display (See not in front of page). Locate and mark the dual 16" wood stud centers closest to the desired plasma placement area. Measure up from the floor the proper distance to the bottom edge of the wall plate and mark a level reference line on the wall. Place the lower portion of the wall plate edge on the reference line and mark the best six (6) each wall plate lag bolt mounting points through the wall plate slots on the wall. Drill 1/4" pilot holes on the six marked walls before installing the plate. Level the wall plate with the wall plate reference arrow pointing up to the wall using the six (6) 5/16" Lag bolts and flat washers (supplied). Step 3 With the upper “clevis” tilt hooks on the plasma brackets in the flat on wall position raise the plasma display with brackets attached (2 people minimum recommended) and place the plasma display flat against wall with the upper and lower plasma bracket attaching slots slightly higher than the steel receiving rods of the wall plate. With the plasma reasonably level lower the display until the display brackets receiving slots are fully installed into the upper and lower wall plate steel rods. Gently pull the left and right upper edges of the display to extend the mount to its maximum 12° tilt and install finger tight the two upper “clevis” arm 6 (mm) safety knobs one on each mounting bracket. Step 4 Once the display on wall installation is complete you still can move the display from left to right or right to left to optimize the final position of the display on the wall by gently sliding the unit on the steel rods of the wall plate. This adjustment distance will vary depending on the display model being installed. NOTE: Some of the hardware may be left out if all the assign mounting points on the bracket are used. BEFORE INSTALLING DETERMINE THE PROPER ROD LOCATION OF THE CTM PLATE: They are two-rod positions on the CTM plate. Lay the CTM plate on the floor with the rod facing up. Slide the top hook of one (1) mounting brackets and determine the position of the bottom rod by where the receiving bottom slot falls under. If the bottom-receiving hook of the mounting bracket is not touching the rod (DO NOT INSTALL THE PLATE), the bottom-receiving slot of the mounting bracket has MUST touch the rod in order to install the CTM plate. Simply remove the 1/4" screws and flat washer from both sides. Slide the rod out and re position the rod on the second optional height. Re install the 1/4" screws and flat washers. MAKE SURE THE ROD IS PROPERLY TIGHTENED BEFORE INSTALLING THE CTM PLATE TO THE WALL. NOTE: Do not over tighten the bracket mounting screws as damage to the display internal mounting threads could occur. Note: The 8 (mm) nuts for your coarse tension adjustment and the 5 (mm) screws for your fine tension adjustment. www.touchboards.com 205 Westwood Ave.Long Branch, NJ 07740 1-866-942-6273 [email protected]
Transcript of CTM-100 Installation Instructions · PDF fileIdentify the correct plasma bracket mounting...
CTM-100 Installation Instructions
Read and understand the installations carefully for a proper installation of the wall mount. Step 1 Invert the display and place it on a soft and flat surface. Locate the mounting points on the back of the plasma display. Identify the correct plasma bracket mounting hardware for your plasma display from the chart shown on the back of the assembly manual and secure the (L) Left and (R) Right hand side mounting brackets to the plasma using the corresponding hardware (supplied). Note: Make sure the upper “clevis” hook mounting screw, nut and reference arrow are facing to the left and right outside edges of the display. Step 2 Temporarily slide the round steel rod portion of one of the CTM plate fully into the bottom receiving slots of the installed plasma mounting brackets. Measure the distance between the bottom outside edge of the plasma display and the bottom outside edge of the wall mounting plate. Add the desired bottom edge height of the display to the distance between the bottom edge of the wall plate and the bottom edge of the display to determine the correct mounting height of the wall plate. Example: Overall desired height for the bottom outside of the display is 60". Difference between the bottom edge of the display and the bottom edge of the wall plate fully installed in the lower receiving slots of the brackets is 4" means the wall plate bottom outside edge should be placed at 64" from the floor (60" + 4" = 64"). Determine the desired wall location and its ability to properly support the weight of the display (See not in front of page). Locate and mark the dual 16" wood stud centers closest to the desired plasma placement area. Measure up from the floor the proper distance to the bottom edge of the wall plate and mark a level reference line on the wall. Place the lower portion of the wall plate edge on the reference line and mark the best six (6) each wall plate lag bolt mounting points through the wall plate slots on the wall. Drill 1/4" pilot holes on the six marked walls before installing the plate. Level the wall plate with the wall plate reference arrow pointing up to the wall using the six (6) 5/16" Lag bolts and flat washers (supplied). Step 3 With the upper “clevis” tilt hooks on the plasma brackets in the flat on wall position raise the plasma display with brackets attached (2 people minimum recommended) and place the plasma display flat against wall with the upper and lower plasma bracket attaching slots slightly higher than the steel receiving rods of the wall plate. With the plasma reasonably level lower the display until the display brackets receiving slots are fully installed into the upper and lower wall plate steel rods. Gently pull the left and right upper edges of the display to extend the mount to its maximum 12° tilt and install finger tight the two upper “clevis” arm 6 (mm) safety knobs one on each mounting bracket. Step 4 Once the display on wall installation is complete you still can move the display from left to right or right to left to optimize the final position of the display on the wall by gently sliding the unit on the steel rods of the wall plate. This adjustment distance will vary depending on the display model being installed.
NOTE: Some of the hardware may be left out if all the assign mounting points on the bracket are used.
BEFORE INSTALLING DETERMINE THE PROPER ROD LOCATION OF THE CTM PLATE: They are two-rod positions on the CTM plate. Lay the CTM plate on the floor with the rod facing up. Slide the top hook of one (1) mounting brackets and determine the position of the bottom rod by where the receiving bottom slot falls under. If the bottom-receiving hook of the mounting bracket is not touching the rod (DO NOT INSTALL THE PLATE), the bottom-receiving slot of the mounting bracket has MUST touch the rod in order to install the CTM plate. Simply remove the 1/4" screws and flat washer from both sides. Slide the rod out and re position the rod on the second optional height. Re install the 1/4" screws and flat washers. MAKE SURE THE ROD IS PROPERLY TIGHTENED BEFORE INSTALLING THE CTM PLATE TO THE WALL.
NOTE: Do not over tighten the bracket mounting screws as damage to the display internal mounting threads could occur.
Note: The 8 (mm) nuts for your coarse tension adjustment and the 5 (mm) screws for your fine tension adjustment.
www.touchboards.com 205 Westwood Ave.Long Branch, NJ 07740 1-866-942-6273 [email protected]
A Mount Brackets L/RB Hardware See ChartC Nylon Spacers (SP) See ChartD Wall Brackets 2E Template 1F 5/16" Lag Bolts 8G 5/16" Flat Washers 8H 6 mm x 12 mm Securing Knobs 2
Note: When the display brackets receiving slots are fully installed into the upper and lower wall plate steel rods and the plasma is on its flat position, there is a 7/8" gap from the top of the rod to the end of the hook. This feature is to compensate for tilting.
Note: Arrows on the wall brackets must be facing up prior to installation. Secure the lag bolts into the center of the wood studs.
#/LR DESCRIPTION QTY
BRAND MODEL # MP HARDWARE PACKDwin HD50 3,9 (4) 8 (mm) x 30 (mm) (SP) PK 2
Fujitsu 4211, 4212, 4221, 4222, 4208, 4209, 4213, 4214, 4229, 4241, 4242, 4233 2,6 (4) 5 (mm) x 16 (mm) PK 1
Fujitsu P42HHA10 3,9 (6) 8 (mm) x 20 (mm) PK 4
Fujitsu P50XHA10, P42VHA105, P4ZHA105, P42HCA11WH, P42VHA20WS, P42VCA21WX 3.A,11.1 (6) 8 (mm) x 30 (mm) PK 7
Fujitsu 5001, 5002, P50XHA10, P50XCA114A 3,9 (4) 8 (mm) x 30 (mm) (SP) PK 2
Fujitsu PDS6101, PDS6001, PDS6002 4.1,12(4) 8 (mm) x 30 (mm) (SP) PK 2
Hitachi CMP500WXU, CMP5000WXU, CMP5003WXU, 50HDT50, 50HDT55 3,5,8
(6) 8 (mm) x 20 (mm) PK 4
JVC GDV500PZU, GDV501U 3,9(4) 8 (mm) x 30 (mm) (SP) PK 2
LG MU40PA10, MU40PA15B 4,7,10 (6) 5 (mm) x 20 (mm) (SP) PK 3
LG MU50PZ41 4,6.2,10 (6) 5 (mm) x 16 (mm) PK 1
LG MN42PZ10, MN42PZ11, MU42PZ10, MU42PZ11B, MU42PZ15B
3.1,6.1,7.1
(6) 5 (mm) X 16 (mm) (SP) Note: Use spacers from pack 3 PK 1
LG MU60PZ10, MU60PZ10, MU60PZ11B 1,5,11(6) 8 (mm) x 20 (mm) (SP) PK 4
Panasonic
TH37PWD4UZ,PT42P1, TC42P1F, 42PD2, PT42PD3P, PT42PD1P, TH42PWD3U, PT37P1, TC42P1, TH42PWD3, TH42PWD4UY, TH42PWD4EX, TH50PHD3U, PT50PD3P, TH50PHD3E, PT37PD4, TH37PW5EX, TH37PA20UP, TH42PHD5U, PT42PD4, PT42PHD4P, TH42PWD5UY, TH42PW5UZ, TH42PWD6UY, TH42PA2oUP, PT50PHD4P, TH50PHW3, TH50PD4, TH50PHD5U, 50PHW5UZ, TH50PHD6U
3,9 (4) 8 (mm) x 30 (mm) (SP) PK 2
Eizo P5070, P5071 3,5,8 (6) 8 (mm) x 30 (mm) PK 7
Maxx 5000 3,5,8 (4) 8 (mm) x 30 (mm) (SP) PK 2
Pioneer
PDP4330HD,PDP501X, V502MX, V502X, V505, PDP505HD,1000HD,PDP503CMX, PDP5030HD, PD433HDE, PDP433CMX, PDP433PU, PDP4300, PDP4340HD, PRO800HD, PRO800HDI, PRO910HD, PDP503MX, PDP503HDE, PDP5031HD, PDP5040HD, PRO1000HDI, PRO1110HD
3,5,8 (6) 8 (mm) x 20 (mm) PK 4
RCA PHD505000 3,5,8 (6) 8 (mm) x 20 (mm) PK 4Runco PL42cx 3,9 (4) 8 (mm) x 30 (mm) (SP) PK 2
Runco PL42CX 3,9 (4) 8 (mm) x 30 (mm) (SP) PK 2
Runco PL43HDX, CW 43MC 3,5,8 (6) 8 (mm) x 20 (mm) PK 4
Runco PL50c, P150HDV, CW 50MC 3,5,8 (6) 8 (mm) x 20 (mm) PK 4
Samsung SPN4235 3,9 (4) 8 (mm) x 30 (mm) (SP) PK 3
Sharp PZ43HV2U,PD50,PZ50HV2U,PZ43HV2U 3,5,8 (6) 8 (mm) x 20 (mm) PK 4
Toshiba PD42W, PD42W1 3,9 (4) 8 (mm) x 30 (mm) (SP) PK 2
Toshiba 50HP81 3,9 (4) 8 (mm) x 30 (mm) (SP) PK 2
Viewsonic VPW420 3,9 (4) 8 (mm) x 30 (mm) (SP) PK 2Viewsonic VPW500 3,5,8 (6) 8 (mm) x 20 (mm) PK 4
Zenith DPDP40W,P40V22,DPDP40V, P40V24 4,7,10(6) 5 (mm) x 20 (mm) (SP) PK 3
Zenith P50W26, P5W28, P50W38 3.2,6.2,10 (6) 5 (mm) x 16 (mm) PK 1
Zenith P42W22, P42W22B, P42W24P, P42W34P 3.1,6.1,7.1 (6) 5 (mm) X 16 (mm) (SP) Note: Use spacers from pack 3 PK 1
Zenith DPDP60W, P60W26, P60W38 1,5,11 (6) 8 (mm) x 20 (mm) (SP) PK 4
AKIRA SV-4201, EPM-420 1,9 (4) 8 (mm) x 30 (mm) (SP) PK 2
Yamaha PDM1 1,9 (4) 8 (mm) x 30 (mm) (SP) PK 2
Cornea MP4200,MP4204 3.1,6.1,7.1 (6) 5 (mm) X 16 (mm) (SP) Note: Use spacers from pack 3 PK 1
Barco Cineversum50 3,5,8 (6) 8 (MM) X 20 (MM) PK 4
DuKane P50 3,5,8 (6) 8 (MM) X 20 (MM) PK 4
Electrograph DTS4230 3,9 (4) 8 (MM) X 30 (MM) (SP) PK 5
Panasonic TH42PX20UP, TH42PX20, TH50TX20UP, TH50PX20UP 3,5,8 (4) M8 X 70 (12) (SP) PK 31
CTM-100
R
LISTEDE176225
The wall or ceiling should be capable of supporting a weight of 160 Lbs at least four (4) times the weight of the plasma display. More than 160 Lbs, the wall or ceiling must be reinforced. Proper installation procedure by qualified personnel as outlined
in the installation instructions must be adhered to. Failure to do so could result in serious personal injury.
redy_juan
white bg
N E W H A R D W A R E
CAUTION! The nylon sleeves and ½” nylon spacers must ALWAYS be used in order to install plasma bracket on to the plasma. Failure to do so will result in damaging the plasma internally. This application is required by
the plasma manufacture.
Nylon sleeves
½" Nylon spacers
ASSEMBLED
NEW HARDWARE APPLIES TO PLASMA MODELS: Fujitsu 50" & 61" 5001, 5002, PDS6101, PDS6001, PDS6002,P50XCA11UH P50XCA10WH, P50XCA10HA P50XCA10UH,P50XCA11WH P50XCA11AH, P50XCA12WH P50XCA12EH, P50XCA12AH P50XCA12UH Panasonic 42", 50" TC42P1, PT42PD3P, PT42PD1P, TC42P1F, PT37P1, TH42PWD3, TH37PWD4UZ, TH42PWD4UY, TH42PWD4EX, PT42P1, 42PD2, TH42PWD3U, TH50PHD3U, PT50PD3P, TH50PHD3E, TH50PHW3 TH42PX20UP, TH42PX20, TH50TX20UP, TH50PX20UP Runco 42" PL42cx, Toshiba 42", 50" 50HP81, PD42W, PD42W1 ViewSonic 42" VPW420, Dwin 50" HD50 JVC 50" GDV500PZU
NOTICE APPLIES TO PCM (REV 8) CTM (REV 8) / PSM / PRM MOUNTS.
