Cross Tour Remo t Start

Publications No.

INSTALLATIONINSTRUCTIONS

Accessory Application

© 2009 American Honda Motor Co., Inc. – All Rights Re

AII 41964
REMOTE CONTROL ENGINE STARTER
served. AII 41964 (0911

2010 ACCORD CROSSTOUR

) 0

Issue Date

NOV 2009

PARTS LISTRemote Engine Starter Unit KitP/N 08E91-E22-101ATransmitter

Control unit

Antenna

Key ring

Protective tape

Caution label

Fuse label

Accessory User’s Information Manual

Quick start guide

Remote Control Engine Starter Attachment KitP/N 08E92-TA0-101Engine starter harness

Control unit bracket

Template

3 Relays

Ground bolt

Flange nut

1 of 238E92-TP6-1000-91

20 Wire ties

2 Long wire ties

8 Urethane tapes

A-Pillar clip

TOOLS AND SUPPLIES REQUIREDFlat-tip screwdriverPhillips screwdriverSmall flat-tip screwdriverRatchet10 mm Socket10 mm Combination wrenchIsopropyl alcoholShop towelTape measureClip removerScissorsSmall rubber malletHonda Diagnostic System (HDS)Masking tape2 Pairs of needle nose pliersDiagonal cuttersUtility knifePlastic Trim Tool (T/N SILTRIMTL10)

2 of 23 AII 41964

Illustration of the Remote Control Engine Starter Installed on the Vehicle

INSTALLATION

1. Make sure you have the anti-theft codes for the audio and navigation system (if equipped), then write down the radio station presets.

2. Disconnect the negative cable from the battery.

Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

711102AY

40A FUSES

ENGINE STARTER HARNESS

ANTENNA

3A FUSE

CONTROL UNIT

(0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.

Setting the Control Unit3. Using a small flat-tip screwdriver, adjust the switches

on the (accessory) control unit to the locations shown.

NOTE:• The switches must be adjusted before the

control unit is plugged in.• If the switch settings are not correct, the remote

engine starter will not operate correctly.• If adjusting the switches with the control unit

installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.

• If you change the switch settings with the unit connected, you must disconnect the unit then reconnect it before the settings change.

932501AS

CONTROL UNIT

SMALL FLAT-TIP SCREWDRIVER

Discharge any static electricity.

SET

SWITCHES

SWITCHES

SW:1 RR Junction unit --------------------> OFF

SW:2 Trunk or Tailgate --------------------> ON

SW:3 Smart Entry --------------------------- > OFF

SW:4 Horn or Buzzer Answerback ----> OFF

SW:5 Trunk Main SW----------------------- > OFF

SW:6 Reserve---------------------------------> ON

© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 41964

4. Using isopropyl alcohol on a shop towel, clean the area where the protective tape will attach. Attach the protective tape to the control unit over the switches.

Removing the Vehicle Parts5. Using a plastic trim tool, disengage the eight

retaining tabs and remove the left and right lenses from the roof console.

772505AS

CONTROL UNIT

SWITCHESPROTECTIVE TAPE

BACKING

Clean with isopropyl alcohol.

931806AS

ROOF CONSOLE

LEFT LENS

4 RETAINING TABS

RIGHT LENS

4 RETAINING TABS

PLASTIC TRIM TOOL

(0911) 3 of 23

6. Open the sunglass holder. Remove the four screws (two black and two silver) and let the roof console drop down. Unplug the vehicle connectors and remove the roof console.

7. Turn the sunvisor holder 45° and remove the two sunvisor holders.

730202AB 2 BLACK SCREWS

ROOF CONSOLE

SUNGLASS HOLDER(Open.)

VEHICLE CONNECTORS

2 SILVER SCREWS

6D1806BY

SUNVISOR HOLDER

Turn.

SUNVISOR HOLDER

4 of 23 AII 41964

8. Pull away the door seal from the left A-pillar trim.

9. Using a small rubber mallet and a shop towel, gently tap the left A-pillar trim at the position shown to release the clip.

10. Pull away the remaining door seal from the left A-pillar trim, and remove the left A-pillar trim (two clips).

711110BY

CLIP

A-PILLAR TRIM

A-PILLAR

PIN

STRIKE POINTSHOP TOWEL

SMALL RUBBER MALLET

LEFT A-PILLAR TRIM

CLIP

DOOR SEAL

Strike perpendicularly to the vehicle.

TRIANGLE MARK

Pull.

6D18070Y

2 CLIPS

DOOR SEAL

LEFT A-PILLAR TRIM


11. Remove and discard the clip from the left A-pillar trim, and install a new A-pillar clip (supplied) onto the left A-pillar trim.

12. Remove the driver’s dashboard lower cover (eight clips, two hooks, and vehicle connector).

6D18080Y

CLIP (Discard.)

LEFT A-PILLAR TRIM

NEW A-PILLAR CLIP

6D1803AY

8 CLIPS

DRIVER’S DASHBOARD LOWER COVER

2 HOOKS

VEHICLE CONNECTOR


13. Remove the driver’s dashboard under cover (three clips and one pin).

14. Raise the front side of the left front door sill trim, and remove the left front door sill trim (four clips and one retaining tab).

6D18040Y

3 CLIPS

DRIVER’S DASHBOARD UNDER COVER

PIN

932502AS

FRONT

RETAINING TAB

LEFT FRONT DOOR SILL TRIM

4 CLIPS

(0911) 5 of 23

15. Pull away the door seal, and remove the left kick panel (two clips).

16. Pull away the door seal, and remove the driver’s dashboard side lid (three clips, four tabs, and three hooks).

932503AS

2 CLIPS

DOOR SEAL

LEFT KICK PANEL

6D1805BY

DRIVER’S DASHBOARD SIDE LID

3 CLIPS

3 HOOKS

DOOR SEAL

4 TABS

6 of 23 AII 41964

17. Lower the tilt lever and pull the steering wheel out.

18. Remove the upper steering column cover:• Insert a flat-tip screwdriver along the column

guide inside the lower steering column cover, and gently pry out the retaining tab of the upper steering column cover.

• Push the lower steering column cover in at the areas shown to release the two retaining tabs, and pull up the upper steering column cover to release the two hooks and one retaining tab.

7215010K

LOWER STEERING COLUMN COVERRETAINING

TAB

TILT LEVER

COLUMN GUIDE

FLAT-TIP SCREWDRIVER

2 HOOKS

2 RETAINING TABS

Push.

RETAINING TAB

UPPER STEERING COLUMN COVER


19. Remove the lower steering column cover (three screws). The upper screws are self-tapping screws.

20. If equipped, remove the vehicle unit (two bolts and vehicle 28-pin connector).

7111090Y

LOWER STEERING COLUMN COVER

SELF-TAPPING SCREWSCREW

732903BY

BOLT

VEHICLE 28-PIN CONNECTOR

VEHICLE UNIT(If equipped)

BOLT


21. Remove the bolt, and remove the vehicle unit from the vehicle bracket.

Routing the Engine Starter Harness22. Using isopropyl alcohol on a shop towel, clean the

areas where the fuse labels will attach.

23. Attach the two 40A fuse labels to the engine starter fuse block.

24. Attach the 3A fuse label to the engine starter relay block.

932518AS VEHICLE BRACKET

BOLT

VEHICLE UNIT

STEERING SHAFT

732821BY


FUSE BLOCK(Clean with isopropyl alcohol.)

3A FUSE LABEL

40A FUSE LABELS

RELAY BLOCK(Clean with isopropyl alcohol.)

(0911) 7 of 23

25. Install the three relays to the engine starter relay blocks.

26. Route the 12-pin/8-pin/5-pin connector end of the engine starter harness over the vehicle bracket towards the center of the vehicle.

6D1802BY


RELAY BLOCKS

3 RELAYS

932520AS


12-PIN/8-PIN/5-PIN CONNECTOR

STEERING SHAFT VEHICLE

BRACKET

8 of 23 AII 41964

27. Route the 12-pin/8-pin/5-pin connector end of the engine starter harness to the ignition switch.

28. Unplug the vehicle 5-pin connector from the ignition switch, and plug the engine starter harness 5-pin connector into the ignition switch.

NOTICE: Check that the engine starter harness 5-pin connector is plugged to the ignition switch and it is locked securely. A loose connector can cause the engine to stall.

6D1812DY

12-PIN/8-PIN/5-PIN CONNECTOR

IGNITION SWITCH


5-PIN CONNECTOR

Unlock connector Lock connector

Push.


Push.Pull.12

3 1

2

Unplug. Plug.


29. Wrap one urethane tape around the vehicle 5-pin connector, and tuck it into the area shown.

30. Unplug the vehicle 12-pin connector and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the combination light switch.

6D1813AY

URETHANE TAPE



VEHICLE BRACKETPush.

Push.

Locked connector1

2

6D18141Y

12-PIN CONNECTORS



COMBINATION LIGHT SWITCH


31. Unplug the vehicle 8-pin connector and plug it into the engine starter harness 8-pin connector. Plug the remaining engine starter harness 8-pin connector into the wiper switch.

32. Using two wire ties, secure the engine starter harness to the vehicle harness. Do not secure to the SRS harness.

6D18151Y



8-PIN CONNECTORS

WIPER SWITCH

6D1816BY

VEHICLE HARNESS


2 WIRE TIES

(0911) 9 of 23

33. Using two wire ties, secure the engine starter harness to the vehicle harness in the areas shown.

34. Unplug the vehicle 20-pin connector from the vehicle unit removed in step 21, and plug it into the engine starter harness 20-pin connector. Plug the remaining engine starter harness 20-pin connector into the vehicle unit.

6D1817BY

VEHICLE HARNESS

VEHICLE CLIP


WIRE TIE

WIRE TIE VEHICLE HARNESS ENGINE

STARTER HARNESS

Inside.

932504AS


20-PIN CONNECTOR

VEHICLE UNIT


20-PIN CONNECTOR


10 of 23 AII 41964

35. Align the green tape on the engine starter harness with the clip on the vehicle harness, and secure the engine starter harness to the vehicle harness using one wire tie.

36. Near the connector, secure the engine starter harness to the vehicle harness using one wire tie.

37. Using two long wire ties, secure the engine starter harness to the vehicle harness at the locations shown.

6D1811AY

VEHICLE HARNESS


WIRE TIE

VEHICLE CLIP

GREEN TAPE

932505BS ENGINE STARTER HARNESS

VEHICLE HARNESSWIRE TIE

VEHICLE HARNESS

LONG WIRE TIE

CONNECTOR


38. Reinstall the vehicle unit to the vehicle bracket using the bolt removed in step 21.

39. Route the engine starter harness along the vehicle harness to the front of the fuse box.

40. Using one wire tie, loosely secure the engine starter harness to the vehicle harness.

932519AS

VEHICLE BRACKET

VEHICLE UNIT

BOLT(removed in step 21)

6D1820AY

WIRE TIE (Loosely secure.)FUSE BOX


VEHICLE HARNESS


41. Unplug the vehicle 5-pin connector from the fuse box. Plug the engine starter harness 5-pin connector into the fuse box 5-pin connector. Wrap one urethane tape around the vehicle 5-pin connector.

NOTICE: Check that the engine starter harness 5-pin connector is plugged to the fuse box 5-pin connector and it is locked securely. A loose connector can cause the engine to stall.

6D1823DY

FUSE BOX


5-PIN CONNECTOR

Unlock connector


Push.Pull.

Push.


URETHANE TAPE

Lock connector

Push.

Lock connector

Push.

122

1

2

3 1Unplug. Plug.

(0911) 11 of 23

42. Plug the engine starter harness 12-pin connector into the fuse box 12-pin connector.

NOTE: If another accessory 12-pin connector is already plugged into the fuse box: Unplug the 12-pin connector from the fuse box, then plug the engine starter harness 12-pin connector into the fuse box. Remove and discard the dummy connector from the engine starter harness, and plug the other accessory 12-pin connector into the engine starter harness 12-pin connector.

6D1821BY

FUSE BOX 12-PIN CONNECTOR

FUSE BOX

ENGINE STARTER HARNESS 12-PIN CONNECTOR

6D1822BY

FUSE BOX 12-PIN CONNECTOR

12-PIN CONNECTOR

12-PIN CONNECTOR

DUMMY CONNECTOR(Discard.)

FUSE BOX

ANOTHER ACCESSORY 12-PIN CONNECTOR


12 of 23 AII 41964

43. Using one wire tie, loosely secure the engine starter harness to the vehicle harness.

44. Unplug the vehicle 20-pin connector (blue), and plug it into the engine starter harness 20-pin connector. Plug the engine starter harness 20-pin connector (white) into the vehicle 20-pin connector.

6D1824AY

VEHICLE HARNESS


WIRE TIE (Loosely secure.)

6D1825AY

FUSE BOX


20-PIN CONNECTOR (White)


20-PIN CONNECTOR VEHICLE 20-PIN

CONNECTOR (Blue)


45. Attach the engine starter harness 20-pin connector to the vehicle connector as shown.

46. Remove and discard the hood opener bolt. Install the ground bolt with the engine starter harness ground terminal attached.

932506AS

HOOD OPENERVEHICLE

CONNECTOR



932507BS

BOLT (Discard.)

HOOD OPENER

VEHICLE PANEL

GROUND BOLT

ENGINE STARTER HARNESS GROUND TERMINAL


47. Using one wire tie, secure the engine starter harness to the vehicle harness.

48. Using two wire ties, loosely secure the engine starter harness to the vehicle harness.

932508BS

WIRE TIE


VEHICLE HARNESS

6D18290Y

VEHICLE HARNESS


2 WIRE TIES (Loosely secure.)

VEHICLE HARNESS

(0911) 13 of 23

Installing the Antenna49. Using scissors, cut out the appropriate template.

932509BS

TEMPLATE(Cut out.)

14 of 23 AII 41964

50. Using scissors, trim the template.EX model:

EX–L model:

932510AS

TEMPLATE

Cut out.

Cut out.

932511AS

TEMPLATE

Cut out.


51. Attach the template to the windshield.EX model:

EX–L model:

932513AS

TEMPLATE

CENTER

BLACK CERAMIC

WINDSHIELDBLACK CERAMIC OF MIRROR BASE

MASKING TAPES

932514AS

TEMPLATE

CENTER WINDSHIELD

BLACK CERAMIC

MASKING TAPES


52. Using two pair of needle nose pliers, bend the antenna plate according to the full scale drawing shown.

721509BY

ANTENNA

PLATE

10 mm(0.4 in.)

SCALE

2 PAIRS OF NEEDLE NOSE PLIERS

10 mm(0.4 in.)

(0911) 15 of 23

53. Starting near the antenna end of the cable, wrap three urethane tapes around the antenna cable at the measurements shown.

54. Cut one urethane tape in half. Wrap the two cut pieces around the antenna cable at the measurements shown.

7111110Y

390 mm(15.3 in.)

20 mm(0.8 in.)

620 mm(24.4 in.)

ANTENNA CABLE

3 URETHANE TAPES

Cut in half.

ANTENNA CABLE

URETHANE TAPE Cut pieces of urethane tape

20 mm(0.8 in.)

16 of 23 AII 41964

55. Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach.

56. Remove the backing from the antenna. Insert the antenna plate over the headliner, and attach the antenna to the windshield aligning it with the template. Press the antenna firmly.NOTE: This antenna should only be installed if the ambient air temperature is 15°C (60°F) or above.

57. Remove the template.

58. Gently pull down the headliner, and tuck the antenna cable under the headliner. Be careful not to crease the headliner.

721510AY

TEMPLATE

HEADLINER

ANTENNAPress firmly.

PLATE

BACKING

Clean with isopropyl alcohol.

932522AS

VEHICLE HARNESS

ANTENNA CABLE

HEADLINER

HEADLINER

ANTENNA CABLE


59. Using isopropyl alcohol on a shop towel, clean the areas where the urethane tapes will attach.

60. Cut one urethane tape in half. Secure the antenna cable to the vehicle panel using the cut pieces of urethane tape.

61. Route the antenna cable down and under the dashboard through the A-pillar trim opening.

932515AS

ANTENNA CABLE

VEHICLE PANEL(Clean with isopropyl alcohol.)

Cut in half.

URETHANE TAPE

VEHICLE HARNESS

932523AS

ANTENNA CABLE

A-PILLAR TRIM OPENING


62. Using four wire ties, secure the antenna cable to the vehicle harness.

63. Using one wire tie, secure the vehicle 5-pin connector unplugged in step 41 to the vehicle harness.

64. Using two wire ties, secure the antenna cable to the vehicle harness.

6D18430Y

ANTENNA CABLE

4 WIRE TIESVEHICLE CLIP

VEHICLE HARNESS

6D1844AY

WIRE TIE

ANTENNA CABLE

WIRE TIE

VEHICLE HARNESS

VEHICLE 5-PIN CONNECTOR(unplugged in step 41)

(0911) 17 of 23

65. Route the antenna cable along the engine starter harness as shown.

66. Secure the antenna cable using the three loosely secured wire ties.

Installation of the Control Unit67. Install the control unit bracket to the control unit.

6D1845BY

ANTENNA CABLE


VEHICLE HARNESS

LOOSELY SECURED WIRE TIE(Secure.)

LOOSELY SECURED WIRE TIE(Do not secure yet.)

6D18461Y

CONTROL UNIT BRACKET

CONTROL UNIT

18 of 23 AII 41964

68. Plug the engine starter harness 28-pin connector into the control unit.

69. Install the clip on the engine starter harness to the control unit bracket.

70. Plug the antenna terminal into the control unit.

6D1847BY

CONTROL UNIT BRACKETCONTROL

UNIT

CLIP

28-PIN CONNECTOR


6D18480Y

ANTENNA TERMINAL

CONTROL UNIT


71. Secure the control unit to the vehicle frame using the flange nut.

72. Wrap one urethane tape around the vehicle connector.

932524AS

VEHICLE FRAME

FLANGE NUT

CONTROL UNIT

932516AS

VEHICLE CONNECTOR

URETHANE TAPE


73. Attach the engine starter harness relay block clip to the vehicle frame.

74. Bundle up the excess antenna cable and secure it to the engine starter harness and the vehicle harness using the loosely secured wire tie.

75. Using two wire ties, secure the antenna cable to the engine starter harness.

6D1860AY

ENGINE STARTER RELAY BLOCK

ENGINE STARTER HARNESS RELAY BLOCK CLIP

VEHICLE FRAME

6D18620Y

ANTENNA CABLE(Bundle up.)


VEHICLE HARNESS

2 WIRE TIES

LOOSELY SECURED WIRE TIE(Secure.)

(0911) 19 of 23

76. Under the hood, locate the area where the caution label will attach. Using isopropyl alcohol on a shop towel, clean the hood where the caution label will attach.

77. Attach the caution label to the hood in the area shown.

78. Reinstall all removed parts. Check that all clips and other fasteners are installed securely. Take care not to pinch the airbag with the clip during reinstallation of the A-pillar trim. Do not push the A-pillar trim excessively.

79. Reconnect the negative cable to the battery.80. Enter the customer’s radio anti-theft code, and reset

the radio station presets.81. Reset the clock.82. Perform “REMOTE ENGINE STARTER

REGISTRATION” and “FUNCTION CHECK.”

932517AS

HOOD(Clean with isopropyl alcohol.)

CAUTION LABEL

BACKING

20 of 23 AII 41964

REMOTE ENGINE STARTER REGISTRATION1. Acquire the PCM Code from ISIS.

2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch on.

3. Start the HDS, and click the car icon.

4. Input the VIN and other requirements in accordance with the HDS, then click the check button.

792901AH

CAR ICON

752502AS

CHECK BUTTONInput the VIN and other requirements.


5. Select “Honda Systems,” then click the check button.

6. Select “R/C ENG STARTER,” and click the check button.

752503AS

CHECK BUTTONSelect “Honda Systems.”

752504AS

CHECK BUTTONSelect “R/C ENG STARTER.”


7. Check that “REMARKS” is shown, then click the check button.

8. Select “REGISTER REMOTE CONTROL ENGINE STARTER UNIT,” then click the check button.

752505AS

CHECK BUTTON

Check that “REMARKS” is shown.

752506AS

CHECK BUTTONSelect “REGISTER REMOTE CONTROL ENGINE STARTER UNIT.”

(0911) 21 of 23

9. Check that “Obtain PCM-code (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA)” is shown, then click the check button.

10. Input the PCM Code, then click the check button.NOTE: To ensure security, the PCM code (password) is changed everyday, so it is impossible to register the remote controlled engine starter if the date of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same.

752507AS

CHECK BUTTON

Check that “Obtain PCM-code (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA)” is shown.

752509AS

CHECK BUTTON

Input the PCM Code.

22 of 23 AII 41964

11. Check that “The registration of the Remote Control Engine Starter Unit has been completed” is shown, then click the check button.

12. Check that “Check that the engine can be started by the Transmitter” is shown, then click the check button.

13. Perform the function test on next the page then remove the HDS.

752510AS

CHECK BUTTON

Check that “The registration of the Remote Control Engine Starter Unit has been completed” is shown.

752511AS

CHECK BUTTON

Check that “Check that the engine can be started by the Transmitter” is shown.


FUNCTION CHECKOperating Conditions• Hood is closed• Shift lever in park• Parking brake is on• The key is out of the ignition• All doors and tailgate closed and locked

Inspection1. Within 1 second, press the command button, and then the start button on the transmitter.

The engine should start if all operating conditions are met.Does the engine start?

2. Press the command button on the transmitter, and within 1 second, press the stop button. The engine should stop.

Does the engine stop?

Yes - Operation is normal.

No:• Make sure all “Operating Conditions” are met.• Check the engine starter harness connections.• Connect the HDS and check for an indicated failure.

(Refer to the appropriate service manual for details.)


No - Check the engine starter harness connections.

3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions:

NOTE: After each test, the ignition key must be cycled, or the driver’s door must be opened and closed.• Move the shift lever out of the P position.• Unlock or open the doors or the tailgate.• Open the hood.• Insert the key in the ignition.• Press on the brake pedal.

Does the engine stop after each of these tests?

4. Check that the power window or the moon roof does not function when the engine is started with the transmitter.5. Press the command button on the transmitter two times and check the vehicle condition on the display.6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away, and in direct sight.


No - Check the engine starter harness connections.


732904AY

DISPLAY

STOP BUTTON

COMMAND BUTTON

START BUTTON

TRANSMITTER

4 (0911) 23 of 23

Cross Tour Remo t Start

Documents

Transcript of Cross Tour Remo t Start