CROSS GEAR PUMPS/ 50 MOTORS - Cross Hydraulics · cross hydraulics pty ltd green catalogue page...
Transcript of CROSS GEAR PUMPS/ 50 MOTORS - Cross Hydraulics · cross hydraulics pty ltd green catalogue page...
CROSS GEAR PUMPS/MOTORS
50 SERIES
The CROSS Series 50 gear pumps/motors feature a gear tooth design that provides more displacement within a given package size. The gear tooth design and pressure balanced loading plates provide for a high volumetric and overall efficiency while operating at a low noise level. Available in 7 sizes, with displacements from 1.52 to 5.20 cubic inches per revolution, this compact unit can deliver up to 45 US. gpm. in a space less than 6-1/2” x 5-3/4” x 7-1/4”.
MATERIAL SPECIFICATIONSBody and end covers.................................................................................. Die cast aluminium alloyGears..........................................................................................................................Sintered metalShafts ........................................................................................................................Hardened steelSeals...................................................................................................................................... Buna NBearings ................................................................. Pressure lubricated, Teflon impregnated sleeve
GENERAL SPECIFICATIONSDisplacement sizes
1.52 1.95 2.32 2.74 3.30 3.80 5.20 cu.in./Rev24.9 32.0 38.0 44.9 54.1 62.3 85.2 cc/Rev
HYDRAULIC PUMPS
Rated working pressure (max. relief valve setting at full flow)..............................3000 psi (207 bar)Maximum shock & surge pressure ....................................................................... 3500 psi (242 bar)Maximum flow rate (delivery).................................................................................. 45 gpm (170 l/m)Maximum speed (continuous - see Inlet Vacuum Curves) ......................................Up to 3000 RPMMaximum horsepower (at rated speed and pressure)................................................. 78 hp (58 kw)Mounting (any position) ...................................................................................... SAE ‘B’ size, 2-BoltWeight............................................................................................................Approx. 19 lbs (8.6 kg)
HYDRAULIC MOTORS
Rated working pressure (max. relief valve setting at full flow)..............................3000 psi (207 bar)Maximum shock & surge pressure ....................................................................... 3500 psi (242 bar)Maximum flow rate (input) ............................................................................ Up to 56 gpm (227 l/m)Maximum speed (continuous) .................................................................................Up to 3000 RPMMaximum horsepower (at rated speed and pressure)...................................Up to 100 hp (74.6 kw)Mounting (any position) ...................................................................................... SAE ‘B’ size, 2-BoltWeight............................................................................................................Approx. 19 lbs (8.6 kg)
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 1.13
CROSS GEAR PUMPS/MOTORS
50 SERIES
STANDARD FEATURES • Rotation: Bi-directional (Dual Rotation) • Ports: Side, SAE #16 (1-5/16” - 12) U.N. O’Ring thread • Internal check valves (no external drain required if back pressure is below shaft seal rating) • Shaft: 7/8” Dia Woodruff keyed (short) • Shaft Seal: 250 psi. (17 bar)
OPTIONAL FEATURES AVAILABLE • Ports: Rear inlet and outlet location (See ‘How to Order’ for port size options) • Shaft: 7/8” Dia SAE splined (13 tooth)
NOTE: Shafts ‘B’ and ‘D’ are available for quantity indent order only.
DIMENSIONAL DATA in inches and (millimeters)
OUTPUT SHAFTSHAFT ‘A’
13 Tooth, 16/32 pitch;30o pressure angle; Flat root side fit; Class I.
SHAFT ‘B’15 Tooth, 16/32 pitch;30o pressure angle; Flat root side fit; Class I.
SHAFT ‘C’Woodruff Key:1” Diameterx 1.4” wide.
SHAFT ‘D’Woodruff Key:1” Diameterx 1.4” wide.
DISPLACEMENTS(Cu.In./Rev.)(cc/rev)
1.5224.9
1.9532.0
2.3238.0
2.7444.9
3.3054.1
3.8062.3
5.2085.2
‘A’ Dimension(Inches)(mm)
5.60142.2
5.80147.3
5.96151.3
6.15156.2
6.40162.6
6.62168.1
7.21183.1
‘B’ Dimensions(Inches)(mm)
4.23107.4
4.43112.5
4.56115.8
4.78121.4
5.03127.8
5.25133.3
5.84148.3
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 1.14
CROSS GEAR PUMPS/MOTORS
50 SERIES
GEAR PUMP - DELIVERY CHARACTERISTICSTYPICAL PERFORMANCE DATA
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 1.15
MODEL 50P015 MODEL 50P027
MODEL 50P019 MODEL 50P033
MODEL 50P023 MODEL 50P038
MODEL 50P052
600 1000 1400 1800 2200 2600 3000RPM
500
1000
1500
2000
2500
3000
PSI
OUTPUT GPM
INPUTHORSEPOWER
4 6 8 10 12 14 16 18
5
1015
20
25
30
600 1000 1400 1800 2200 2600 3000RPM
500
1000
1500
2000
2500
3000
PSI
OUTPUT GPM
INPUTHORSEPOWER
6 8 10 12 14 16 18
510
1520
25
30
3540
20 22 24
600 1000 1400 1800 2200 2600 3000RPM
500
1000
1500
2000
2500
3000
PSI
OUTPUT GPM
INPUTHORSEPOWER
5
10
20
30
8 10 12 14 16 18 20 22 24 26 28 30 32
40
50
600 1000 1400 1800 2200 2600 3000RPM
500
1000
1500
2000
2500
3000
PSI
OUTPUT GPM
INPUTHORSEPOWER
51020
30
12 16 20 24 4028 3632
40
50
60
70
600 1000 1400 1800 2200 2600 3000RPM
500
1000
1500
2000
2500
3000
PSI
OUTPUT GPM
INPUTHORSEPOWER
51020
30
12 16 20 24 4028 3632
40
50
60
600 1000 1400 1800 2200 2600 3000RPM
500
1000
1500
2000
2500
3000
PSI
OUTPUT GPM
INPUTHORSEPOWER
6 8 10 12 14 16 18
5
10152025303540
20 22 24 26 28
600 1000 1400 1800RPM
500
1000
1500
2000
2500
3000
PSI
OUTPUT GPM
INPUTHORSEPOWER
10
20
30
12 16 20 24 4028 3632
40
50
60
70
44
CROSS GEAR PUMPS/MOTORS
50 SERIES
GEAR PUMP - SUCTION CHARACTERISTICSTYPICAL PERFORMANCE DATA
DO NOT operate above the RPM-inlet vacuum curve or 8 in. Hg. for specific inlet port sizes shown.
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 1.16
MODEL 50P015 MODEL 50P033
MODEL 50P019 MODEL 50P038
MODEL 50P023 MODEL 50P052
MODEL 50P027
1000
1500
2000
2500
3000
0 2 4 6 8 10 12INLET VACUUM ~ IN. HG.
1 5/16 - 12 INLET
(1.0 INCH INLET LINE)
RPM
(1.125 INCH INLET LINE)
(1.0 INCH INLET LINE)
1 5/16 - 12 INLET
1000
1500
2000
2500
3000
0 2 4 6 8 10 12INLET VACUUM ~ IN. HG.
1 7/8 - 12 INLET
RPM
1 5/8 - 12 INLET
(1.50 INCH INLET LINE)
(1.0 INCH INLET LINE)
1 5/16 - 12 INLET
1000
1500
2000
2500
3000
0 2 4 6 8 10 12INLET VACUUM ~ IN. HG.
1 5/8 - 12 INLET
(1.25 INCH INLET LINE)
RPM
1 7/8 - 12 INLET(1.50 INCH INLET LINE)
(1.125 INCH INLET LINE)
(1.0 INCH INLET LINE)1 5/16 - 12 INLET
1000
1500
2000
2500
3000
0 2 4 6 8 10 12INLET VACUUM ~ IN. HG.
RPM
1 5/8 - 12 INLET
(1.0 INCH INLET LINE)
1 5/16 - 12 INLET
1000
1500
2000
2500
3000
0 2 4 6 8 10 12INLET VACUUM ~ IN. HG.
1 5/8 - 12 INLET
(1.25 INCH INLET LINE)
RPM
1 7/8 - 12 INLET
(1.50 INCH INLET LINE)
(1.125 INCH INLET LINE)
(1.0 INCH INLET LINE)
1 5/16 - 12 INLET1000
1500
2000
2500
3000
0 2 4 6 8 10 12INLET VACUUM ~ IN. HG.
RPM 1 5/8 - 12 INLET
(1.0 INCH INLET LINE)
1 5/16 - 12 INLET
1000
1500
2000
2500
3000
0 2 4 6 8 10 12INLET VACUUM ~ IN. HG.
1 7/8 - 12 INLET (1.50 INCH INLET LINE)
RPM
(1.25 INCH INLET LINE)
1 5/16 - 12 INLET
CROSS GEAR PUMPS/MOTORS
50 SERIES
GEAR MOTORSTYPICAL PERFORMANCE DATA
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 1.17
MODEL 50M015 MODEL 50M027
MODEL 50M019 MODEL 50M033
MODEL 50M023 MODEL 50M038
MODEL 50M052
600 1000 1400 1800 2200 2600 3000RPM
500
1000
1500
2000
2500
3000
PSI
INPUT GPM
HORSEPOWEROUT
6 8 10 12 14 16 18
5
10
15
20
25
100
200
300
400
500
600
TORQUEOUTPUT(In-Lbs)
600 1000 1400 1800 2200 2600 3000RPM
500
1000
1500
2000
2500
3000
PSI
INPUT GPM
HORSEPOWEROUT
8 10 12 14 16 18
10
20
200
400
600
TORQUEOUTPUT(In-Lbs)
20 22 24
30
800
26 28
1000
30 32
40
600 1000 1400 1800 2200 2600 3000RPM
500
1000
1500
2000
2500
3000
PSI
INPUT GPM
HORSEPOWEROUT
6 8 10 12 14 16 18
5
10
15
20
100
200
300
400
500
600
TORQUEOUTPUT(In-Lbs)
20 22 24
30
700
800
600 1000 1400 1800 2200 2600 3000RPM
500
1000
1500
2000
2500
3000
PSI
INPUT GPM
HORSEPOWEROUT
12 16
10
20
200
400
600
TORQUEOUTPUT(In-Lbs)
20 24
30
800
28
1000
32
40
36 40
50
1200
1400
600 1000 1400 1800 2200 2600 3000RPM
500
1000
1500
2000
2500
3000
PSI
INPUT GPM
HORSEPOWEROUT
8 10 12 14 16 18
5
10
1520
100200
300400500600
TORQUEOUTPUT(In-Lbs)
20 22 24
30700800
26 28
25
900
10001100
HORSEPOWEROUT
4 8 12 16 20 24 28 32 36 40 44 48 52 56INPUT GPM
500
1000
1500
2000
2500
PSI
200 600 1000 1400 1800 2200 2600RPM
10
20
30
4050
60
70
400
800
1200
1600
TORQUEOUTPUT(In-Lbs)
600 1000 1400 1800 2200 2600 3000RPM
500
1000
1500
2000
2500
3000
PSI
INPUT GPM
HORSEPOWEROUT
12 16
10
20
400
600TORQUEOUTPUT(In-Lbs)
20 24
30 800
28
1000
32
40
36 40
50 1200
1400
1600
CROSS GEAR PUMPS/MOTORS
50 SERIES
GEAR MOTORS
TYPICAL PERFORMANCE DATA
VOLUMETRIC EFFICIENCY
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 1.18
0 1000 1400 1800 2200 2600R P M
75
80
85
90
95
100
VOLUMETRICEFFICIENCY~%
AT3000PSI
50M017
50M019
50M02350M027
50M033
50M038
50M052
3000
VOLUMETRIC EFFICIENCY VS RPM AT 120oF
0 500 1000 1500 2000 2500 3000
PRESSURE ~ PSI
200
400
600
STARTINGTORQUE~IN.-LBS.
800
1000
1200
1400
1600
1800
2000
2200
2400
50M052
50M038
50M033
50M027
50M02350M01950M015
STARTING TORQUE (IN.-LBS.) VS PRESSURE (PSI)
STARTING TORQUE
CROSS GEAR PUMPS/MOTORS
50 SERIES
HOW TO ORDER
Series Type SpecialOptions
Sizecu.in./rev x 0.1
Rotation Mounting ShaftSize & Type
Ports
Location Code
SizeInlet Outlet
50 P*(Pump)
M(Motor)
ONone
H*250 psi
Shaft Seal
151923273338 52
D*Dual
RRight
LLeft
B*SAE ‘A’2-Bolt
A7/8”
SplineB*1”
Spline C
7/8” Dia Keyed
D7/8” Dia Keyed(Long)
SA1-7/8”
UN O’Ring
1-5/16”UN
O’Ring
SideSB
1-5/8”UN
O’Ring
1-5/16”UN
O’Ring
SC1-5/16”
UN O’Ring
1-5/16” UN
O’Ring
RD1-7/8”
UN O’Ring
1-5/16”UN
O’Ring
Rea
r
RE1-5/8”
UN O’Ring
1-5/16”UN
O’Ring
RF1-5/16”
UN O’Ring
1-5/16”UN
O’Ring
* Standard
EXAMPLE: 50PH23DBCSCDescribes a Series 50 Gear Pump/Motor fitted with a high pressure shaft seal; a displacement of 2.3 cu.in./rev; Bi-directional rotation; SAE ‘B’ 2-Bolt Mount, 7/8” Dia keyed shaft and 1-5/16” UN O’Ring side Inlet & Outlet Ports.
NOTE: Series 50 Pumps only are stocked. Because of the high pressure shaft seal and the dual rotation feature they can be substituted where required for use as motors.When used as a motor a case drain connection is only required when the outlet/return pressure is likely to exceed 250 psi.
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 1.19
PART NUMBER DESCRIPTION SERIES1 5P0013001 Thrust Plate All
2
5P00120015P00120025P00120035P00120045P00120055P00120065P0012016
Driven Gear
50P/M01550P/M01950P/M02350P/M02750P/M03350P/M03850P/M052
3
5P00110075P00110085P00110095P00110105P00110115P00110125P0011142
Drive Gear Assy13 Tooth Spline
50P/M01550P/M01950P/M02350P/M02750P/M03350P/M03850P/M052
5P00110015P00110025P00110035P00110045P00110055P00110065P0011149
Drive Gear Assy7/8” Dia Keyed
50P/M01550P/M01950P/M02350P/M02750P/M03350P/M03850P/M052
CHECK VALVESFOR DUALROTATION.
( REAR VIEW )
SERIES 50 GEAR PUMP and MOTOR
A DB C G
6 10 12 8 1 2 5 4
10128113
7119
TORQUE TO
35 - 40 FT. LBS.
Parts Exploded
VENT HOLE ON INLET( LOW PRESSURE SIDE )SINGLE ROTATION PUMPS ONLY.
CASE DRAIN PORT -USE WHEN BACK PRESSUREEXCEED SEAL RATING.
( DUAL ROTATION ONLY )
3
PART NUMBER DESCRIPTION SERIES
4
5P00070075P00070085P00070125P00070155P00070165P0007019
Rear Cover Assy
All - SC PortingAll - RF PortingAll - SB PortingAll - SA PortingAll - RE PortinhAll - RD Porting
5
5P00040015P00040025P00040035P00040045P00040055P00040065P0004010
Body
50P/M01550P/M01950P/M02350P/M02750P/M03350P/M03850P/M052
6 5P0003003 Front Cover Assy All
7 5A0009 Shaft Seal All
8 5A0077 Loading Seal All
9 2A0466175 Retaining Ring All
10 2A0310710 Dowel Pin All
11 2A0079630 Cap Screw All
12 1A1265 Static Seal All
13 5A0005 Woodruff Key All
5P0017004 SEAL KIT All
Cross Gear Pumps & Motors
September 2007Page 8.01CROSS
CROSS CROSS
Model Gear Width Body Width
40P005 0.372” 0.779”
40P007 0.558” 0.965”
40P010 0.744” 1.151”
40P012 0.930” 1.337”
40P015 1.116” 1.523”
40P018 1.339” 1.746”
50P015 0.675” 1.082”
50P019 0.867” 1.274”
50P023 1.031” 1.438”
50P027 1.218” 1.625”
50P033 1.467” 1.874”
50P038 1.689” 2.096”
50P052 2.311” 2.718”
60P040 1.015” 1.518”
60P051 1.280” 1.783”
60P061 1.545” 2.048”
60P071 1.795” 2.298”
60P081 2.045” 2.548”
60P092 2.325” 2.828”
Field Identification:
Direction of rotation is marked on the unit. Stock number is a 6 digit starting with 3..... (date code and partial description noted as below) stamped on the flange.
Measure width of body or gears if unable to read computer stock number.
300000
CONTROL NUMBER(MAY INCLUDE DESCRIPTIVE NO.)
BODY WIDTH:MEASURE THIS AND REFERTO CHART
DIRECTION OF ROTATION= DUAL
P = PUMPM = MOTOR
DATE CODE
NO. OF WEEKS AFTERJAN 1.
YEAR
TESTERS CODE
FIRST 2 DIGITS OFDISPLACEMENT.
OMIT IF FULL DESCRIPTIVENUMBER IS USED.
23 P12 97 AB
PERFORMANCE DATA - PUMPS: GPM/RPM PERFORMANCE DATA - MOTORS: RPM/GPM
RPM 1000 1500 2000 2500 3000 GPM 5 10 15 20 30 50
MODEL GPM GPM GPM GPM GPM MODEL RPM RPM RPM RPM RPM RPM
40P00540P007
1.72.8
2.64.1
3.55.5
4.36.9
5.28.3
40M00540M007
17321155 2310
40P01040P012
3.74.9
6.57.3
7.49.7
9.212.1
11.014.6
40M01040M012
866693
17321386
25992079
40P01540P018
5.87.0
8.810.5
11.714.0
14.617.5
17.5 40M01540M018
577481
1155962
17321443
23101925 2887
50P01550P019
5.97.6
8.811.4
11.815.2
14.619.0
17.822.8
50M01550M019
684533
13681066
2052 1599
27362132
50P02350P027
9.010.7
13.616.0
18.121.4
22.626.7
27.132.0
50M02350M027
448379
896759
13441138
17921518
26882276
50P03350P03850P052
12.914.820.3
19.322.230.4
25.729.640.6
32.137.0
38.6 50M03350M03850M052
315274199
630547400
945821
12601094800
189016411199
27361999600
60P04060P051
15.820.1
23.730.1
31.640.1
39.450.2
47.360.2
60M04060M051
257202
513404
770606
1027807
15401211
25672018
60P06160P071
24.027.9
36.041.8
47.955.7
59.969.6
71.883.6
60M06160M071 169 338
291507436
676582
1014872
16901454
60P08160P092
31.836.0
47.654.1
63.572.1
79.4901
60M08160M092
255225
383337
510450
765 12751124674
Note: Above performance figures are approximate and are based on 2000 psi operating pressure. Operation on shaded areas is not recommended. Maximum speeds achievable using largest stepped port sizes. Refer to Green Catalogue page 1.02 for Pump Speed vs Port Size Limitations.
GENERAL TECHNICALThe CROSS fixed displacement, gear type pumps and motors have been designed, manufactured and tested to insure the highest quality. This manual has been prepared to assist in the application and installation in order to obtain optimum performance.
Rated working pressure................................ up to 3000 psiMaximum shock and surge pressure............ up to 3500 psiMaximum speed, continuous.............................. see chartsMinimum speed recommended.............................. 600 rpm
PERFORMANCE DATA - PUMPS: GPM/RPM PERFORMANCE DATA - MOTORS: RPM/GPMRPM 1000 1500 2000 2500 3000 GPM 5 10 15 20 30 50MODEL GPM GPM GPM GPM GPM MODEL RPM RPM RPM RPM RPM RPM40P00540P007
1.72.8
2.64.1
3.55.5
4.36.9
5.28.3
40M00540M007
17321155 2310
40P01040P012
3.74.9
6.57.3
7.49.7
9.212.1
11.014.6
40M01040M012
866693
17321386
25992079
40P01540P018
5.87.0
8.810.5
11.714.0
14.617.5
17.5 40M01540M018
577481
1155962
17321443
23101925 2887
50P01550P019
5.97.6
8.811.4
11.815.2
14.619.0
17.822.8
50M01550M019
684533
13681066
2052 1599
27362132
50P02350P027
9.010.7
13.616.0
18.121.4
22.626.7
27.132.0
50M02350M027
448379
896759
13441138
17921518
26882276
50P03350P03850P052
12.914.820.3
19.322.230.4
25.729.640.6
32.137.0
38.6 50M03350M03850M052
315274199
630547400
945821
12601094800
189016411199
27361999600
60P04060P051
15.820.1
23.730.1
31.640.1
39.450.2
47.360.2
60M04060M051
257202
513404
770606
1027807
15401211
25672018
60P06160P071
24.027.9
36.041.8
47.955.7
59.969.6
71.883.6
60M06160M071
169 338291
507436
676582
1014872
16901454
60P08160P092
31.836.0
47.654.1
63.572.1
79.4901
60M08160M092
255225
383337
510450
765 12751124674
NOTE: ABOVE PERFORMANCE FIGURES ARE APPROXIMATE AND ARE BASED ON 2000 PSI OPERATING PRESSURE. OPERATING IN SHADED AREAS IS NOT RECOMMENDED.
FOR DRIVE HP REQUIRED: Multiply flow (gpm) by pressure (psi) and divide by 1714. FOR MAX. PUMP SIZE: (for use with gas engine): Multiply rated engine HP by 1028 and divide by pressure (psi). This gives maximum flow rate (gpm). Select the nearest pump size from the above chart according to drive speed. FOR MOTOR DRIVE TORQUE: Multiply HP by 5252 and divide by RPM.
FOR HYD. MOTOR SIZE: Multiply torque (ft. lbs.) by 88 and divide by pressure (psi). This gives motor size in cu.in./rev. Select nearest motor size from the above chart. For full load starting, use a 10% larger motor size.
HP = GPM x PSI 1714
GPM = 1028 HP PSI
TORQUE = 5252 HP(ft. lbs.) RPM
DISP. = 88T PSI
CROSS GEAR PUMPS/MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 1.01
CROSS GEAR PUMPS/MOTORS
OIL RECOMMENDATIONS: Premium quality anti-wear type oil with a viscosity between 100 and 200 SSU at operating temperatures. Automatic transmission fluids are acceptable. Do not use synthetic fluids.
FILTRATION: 25 micron filters are required with 10 micron preferred. If pump inlet filters are used, be certain inlet flow is not restricted. Cavitation will severely reduce pump life.
PUMP SPEED/PORT SIZE LIMITATIONS: If pumps are operated at speeds higher than shown below, cavitation and pump damage can occur.
PLUMBING SIZE RECOMMENDATIONS: The following is based on 4 ft./sec. inlet velocity and 15 ft./sec. outlet velocity.
SERIES & SIZE
PUMP INLET PORT SIZE
1-1/16 12 1-5/16 12 1-5/8 12 1-7/8 12 2” S.F.3/4” (12) 1” (16) 1-1/4” (20) 1-1/2” (24) 2”
3500 3500
40 S
ER
IES
53400 350072500 350010
12 2000 350015 1750 300018 1400 2500
50 S
ER
IES
15 3000 3000 300019 2300 3000 300023 2000 3000 3000
1700 2600 3000271400 2100 3000331200 1800 2700381000 1600 220052
60 S
ER
IES
40 2000 3000 30001750 2500 3000511400 2200 300061
71 1000 1900 300081 800 1600 260092 600 1400 2500
GPMPUMP INLET PUMP OUTLET
PIPE TUBE HOSE PIPE TUBE HOSE
5 3/4” 7/8” 3/4” 1/4” 3/8” 3/8”
10 1” 1” 1” 3/8” 1/2” 1/2”
15 1 1/4” 1 1/4” 1 1/4” 1/2” 5/8” 1/2”
20 1 1/2” 1 1/2” 1 1/2” 3/4” 3/4” 3/4”
25 1 1/2” 1 1/2” 1 1/2” 3/4” 7/8” 3/4”
30 1 3/4” 1 3/4” 1 3/4” 1” 1” 1”
35 2” 2” 2” 1” 1 1/4” 1”
40 2 1/4” 2 1/4” 2 1/4” 1 1/4” 1 1/4” 1 1/4”
50 2 1/2” 2 1/2” 2 1/2” 1 1/4” 1 1/2” 1 1/4”
75 3” 3” 3” 1 1/2” 1 3/4” 1 1/2”
Tube sizes are OD. Hose sizes are ID.Reduce plumbing size to match pump port size AT PUMP.
BASED ON INLET RESTRICTION (6” HG MAX. VACUUM)MOUNTING: Pumps an motors may be mounted in any position. DIRECT FLANGE MOUNTING: Mount directly to gear box or engine PTO, carefully inserting shaft and pilot into mating holes. Make certain that shaft size and type matches drive. FOOT MOUNT WITH COUPLING: Excessive wear and reduce life will occur due to misalignment. Minor misalignment can be compensated for by using a flexible coupling. FOOT MOUNT WITH BELT OR CHAIN DRIVE: Excessive wear will occur with misalignment.
MISALIGNMENT
ANGULAR OFF-SET(.005 T.I.R. MAX.)
ANGULAR OFF-SET
B
LOAD
RH ROTATION
INLET
A
LOAD
SIDE LOAD:
BI - DIRECTIONALROTATION
LOAD
CLOAD
L
Side loads resulting from belt or chain drives should be kept as close to the housing as possible (ie., keep dimen-sion ‘L’ to a minimum). For maximum life, loads should be applied at quadrant ‘A’ for pumps (RH), quadrant ‘B’ for motors (RH), ‘A’ for LH motors, ‘B’ for LH pumps, and ‘C’ for bi-rotational motors.
CROSS HYDRAULICS PTY LTDCROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 1.02
CROSS GEAR PUMPS/MOTORS
DIRECTION OF ROTATION:Right hand (RH) or left hand (LH) pumps or motors, if oper-ated in the wrong direction, will result in THE IMMEDIATE FAILURE of the shaft seal. Pump and motor rotation is NOT field reversible. Dual rotation (D) units may be operated in either direction.
They also can be operated as either a pump or motor. The correct direction of rotation can be determined by the model number stamped on the front cover.
DRAIN PORT CONNECTION: If the motor outlet port pressure exceeds the rating of the shaft seal (20 psi standard), the drain port must be connected directly to the reservoir. Dual rotation pumps have drain port connections for use as motors.
START-UP PROCEDURES:1. Prior to installation, check pump or motor for possible damage in shipping or handling.2. Install unit, tighten fittings and fill reservoir with clean fluid.3. Fill pump/motor with fluid through drain port connection or inlet port.4. Start engine and run at lowest speed. Check system for air (suction) leaks and oil leaks. (Use a piece of cardboard or wood when searching for possible oil leaks, DO NOT USE HANDS). Bleed air from system if necessary. Operate system at normal speed.5. Gradually increase load to normal, checking for leaks, abnormal noises, binding, etc. Operate system for 15 minutes. Shut off and check filters. Clean or replace as necessary.
MAINTENANCE:1. Clean or replace filters on a regular basis, as necessary.2. Check for presence of water in oil (cloudy or milky appearance) and for presence of air (foamy oil). A rancid odour indicates excessive heating of the oil.3. Check reservoir regularly for proper level. Fill as needed. Repair leaks.
FOR ALL PUMPS AND MOTORS, REFER TO SPECIFIC SPECIFICATION SHEETS FOR ADDITIONAL DATA AND LIST OF OPTIONS AVAILABLE.
NOTE: If chronic shaft seal failure occurs: 1. Check direction of rotation. 2. Check outlet port or drain port pressure. 3. Replace shaft seal with higher pressure rating seal. (See available seal kits)
INLETPORT
RH
CLOCKWISE
OUTLETPORT
INLETPORT
COUNTERCLOCKWISE
LH
14 18NPTF
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 1.03
CROSS GEAR PUMPS/MOTORS
HELPFUL NOMOGRAPHS
PUMP and MOTOR HORSEPOWER PIPE FLOW CAPACITY
HP = PSI X GPM X 0.000583
PUMP DRIVE = THL. HP : EFFICIENCYMOTOR OUTPUT = THL. HP X EFFICIENCY
AREA = GPM X 0.3208 VELOCITY (FT./SEC.)
*Recommendations are for oils having a maximum viscosity of 315 S.S.U. at 100 F operating at temperatures between 65 F and 155 F.
GPM in these NOMOGRAPHS relates to US. GPM.
1 US. GPM = 3.79 Litres
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 1.04
CROSS GEAR PUMPS/MOTORS
HELPFUL NOMOGRAPHS
HYDRAULIC MOTOR TORQUE HYDRAULIC MOTOR SPEED
TORQUE = DISPL. X PRESSURE 2
GPM in these NOMOGRAPHS relates to US. GPM.
1 US. GPM = 3.79 Litres
FLOW RATE = SPEED X DISPL. 231
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 1.05