cover helper H800+01 - Afinia 3D Printer...To resume, close the font door and double click . Opening...
1
For further explanaon check the manual R PRINTER MAINTENANCE Lubricate the rails that form the print head gantry system every 4-6 months or as needed. Refer to the User's Manual for details. Prinng Paused Single letter remains on: If you encounter any issues, have any quesons, feature requests, or feedback for our support team, please contact your local reseller. SUPPORT Red Pulsing: Error Opening the front door pauses the ongoing print job. To resume, close the font door and double click . Opening the top door will not pause the printer. If the printer runs of of filament while prinng, it will automacally pause. Load new filament and double press resume . If there is a loss of power while prinng, use the soſtware to inialize the printer and resume the print. Do not remove the perf board before aempng to resume the print. If prinng with PLA and the room temperature exceeds 85° F (30° C), print with the top door open to reduce the potenal issues while prinng. ON / OFF (15 mins) Table pre-heang progress or print progress during prinng www.afinia.com/support Soſtware, FAQs & updates Turn off the printer and unplug the power before performing any service on the printer such as removing parts, cables or covers. Contact Technical Support for instrucons. WARNINGS Replace the HEPA filter aſter 300 hours of use or every 6 months, whichever happens first. The filter is inside the round filter cover with the white trim located to the leſt of the plaorm . Refer to the User's Manual for details. Yellow Pulsing: Printer switched on waiting to be initialized Green Pulsing: Printer initialized waiting for job Blue Letter Rotation: Fast - Print job spooling Slow - Printing Blue Pulsing: NOTE: Before you can use the printer, you must read the Quick Start Guide and User Manual support@afinia.com Always have adult supervision when children are are present. Small printed parts may be choking hazards -- please keep small parts from children. Make sure to e back loose clothing and long hair while the printer is in operaon. 0% 100% 2 50% US (952) 279-2643 (M-F 8-5 CT) Japan 03-3561-2266 NOTE +
Transcript of cover helper H800+01 - Afinia 3D Printer...To resume, close the font door and double click . Opening...
For further explanationcheck the manual
R
PRINTER MAINTENANCELubricate the rails that form the print head gantry system every 4-6 months or as needed.Refer to the User's Manual for details.
Printing Paused
Single letter remains on:
If you encounter any issues, have any questions, feature requests, or feedback for our support team, please contact your local reseller.
SUPPORT
Red Pulsing: Error
Opening the front door pauses the ongoing print job.To resume, close the font door and double click .Opening the top door will not pause the printer.
If the printer runs of of filament while printing, it willautomatically pause. Load new filament and doublepress resume .
If there is a loss of power while printing, use the software to initialize the printer and resume the print. Do not remove the perf board before attempting to resume the print.
If printing with PLA and the room temperature exceeds 85° F (30° C), print with the top door open to reduce the potential issues while printing.
ON / OFF(15 mins)
Table pre-heating progress or print progress during printing
www.afinia.com/supportSoftware, FAQs & updates
Turn off the printer and unplug the power beforeperforming any service on the printer such as removing parts,cables or covers. Contact Technical Support for instructions.
WARNINGS
Replace the HEPA filter after 300 hours of use or every 6 months, whichever happens first.The filter is inside the round filter cover with the white trim located to the left of the platform .Refer to the User's Manual for details.
YellowPulsing:
Printer switched on waiting to be initialized
GreenPulsing:
Printer initialized waiting for job
Blue Letter Rotation:
Fast - Print job spoolingSlow - Printing
BluePulsing:
NOTE: Before you can use the printer, you must read the Quick Start Guide and User Manual
support@afi nia.com
Always have adult supervision when children areare present. Small printed parts may be choking hazards --please keep small parts from children.
Make sure to tie back loose clothing and long hairwhile the printer is in operation.
0% 100%
2
50%
US (952) 279-2643 (M-F 8-5 CT)
Japan 03-3561-2266
NOTE
+
