Cost Reduction in Heat Treatment With Protective Coatings

5/24/2018 Cost Reduction in Heat Treatment With Protective Coatings

Cost Reduction in Heat Treatment with

Protective Coatings

This article introduces a practical technique pioneered by a metallurgist from the Indian

Institute of Technology. The technique enables any kind of steel to be heated without the

problems associated with oxidation and decarburisation.

When steel is heated in an open furnace in the presence of air or products of combustion, two

surface phenomena take place: 1. Oxidation, and 2. Decarburisation.

Oxidation

Oxidation of steel is caused by oxygen, carbon dioxide and/or water-vapour. The general reactions

are given below:

Oxidation of steel may range from a tight, adherent straw-coloured film that forms at a temperature

of about 180oC to a loose, blue-black oxide scale that forms at temperature above about 450oCwith resultant loss of metal.

Decarburisation

Decarburisation or depletion of surface carbon content takes place when steel is heated to

temperatures above 650oC. It progresses as a function of time, temperature and furnace

atmosphere.

Typical reactions involved are:

The equilibrium relationship depends on the ratio of carbon dioxide to carbon monoxide. It isneutral to a given carbon content at a given temperature.

Harmful Effects of Oxidation and Decarburisation

Oxidation leads to loss of dimensions and material as extra material allowance needs to be kept for

scaling. Often, surface quality is deteriorated due to pitting. Metallurgical transformation duringaustenitising and subsequent quenching may be non-uniform. Surface hardness and strength are

also lowered due to layer of scaling. Fatigue strength of heat treated product is reduced. This is

especially true in case of automobile leaf springs.

Preventing Oxidation and Decarburisation

Prevention of oxidation and decarburisation is not only better than cure, it is profitable too. Thereare several ways to address problems caused by the two harmful reactions. Decarburised surface

removal by machining operations after heat treatment, copper plating of thickness up to 0.025 mm

prior to heat treatment or change of heating media to molten salt bath are some ideas. A number ofprotective atmospheres may be introduced like liquid hydrocarbon, dissociated ammonia,

exothermic gas, nitrogen and endothermic gas. Fluidised bed furnaces and vacuum furnaces have


also proven to reduce scaling. Switching over to grades which do not require heat treatment is

possible in rare cases. However, most of the mentioned solutions pose a number of problems or

practical difficulties. Availability of capital and human resource for using high-end furnaces is amajor issue. Many small heat treatment shops cannot afford these solutions. Yet they are under

mounting pressure to prevent oxidation and decarburisation. Use of protective anti-scale coating

has proven to be a logical solution to the problem of scaling and decarburisation.

Insights into Use of Protective Coating and its Characteristics

Use of protective coating has been found beneficial and cost-effective. An anti-scale coating isapplied on components or billets to be heated before charging them into furnace. This anti-scale

coating acts as a barrier between oxygen and metal. Care is taken to apply a uniform, imperviouslayer of coating on the component to be heated. Coating ensures prevention of scaling and

decarburisation. For exceptionally long heat treatment cycles of 10 to 15 hours, the extent of

scaling and decarburisation mechanism is substantially reduced. Anti-scale coating also reducesdecarburisation on billets and ingots during hot forging and hot rolling operations. Heat transfer

from heating media to metal is not affected due to anti-scale coating.

No reaction with steel surface, no release of toxic fumes during use or heat treatment or storage,non-hazardous and economical implementation are other required characteristics of the coating.

Coated tools and components must be able to be heat treated in air using a box type or bogie

hearth; electric, gas or oil fired furnace.

Benefits of Protective Anti-scale Coating - Case Studies & Success Stories

Table-1 shows the efficacy of the coating in an electric furnace. Coating eliminates the need of salt

bath or controlled - atmosphere equipment in many cases. Considerable savings in capital

investment and operating costs are enabled by use of anti-scale coating. Due to prevention of

decarburisation, uniform surface hardness is achieved. Rejected components can be salvaged(Figure 1). Large savings are possible when plates of expensive alloy steel can be re-heat treated

by using the anti-scale coating. (Figure 2) Due to prevention of oxidation even in ordinary oil fired

furnace by use of protective anti-scale coating, pickling time could be reduced by 75 per cent incase of hot forming and solution annealing of stainless steel tubes and stainless steel pipe fittings.

Buffing could be eliminated or minimised in many cases as scaling was substantially reduced. In

manufacturing process of shearing blades of expensive high carbon, high chromium grade steel,grinding allowance is substantially reduced when protective anti scale coating is applied prior to

heat treatment. Some other distinct case studies are enlisted below.


1. Prevention of Quench Cracks

Forgings like knuckle joints and crank shafts when heat treated in furnaces of oxidising

atmosphere are susceptible to quench cracking. Quench cracks appear when stresses generated

during quenching are higher than tensile strength of sections of forgings that are thinner comparedto the rest of the forging and due to differential quench severity at different areas. Chrome-moly

grades of steel are most susceptible to quench cracks, which usually occur in the gear-end portion

of the crankshaft. By coating the gear-end with protective anti-scale coating, the quench crackingis effectively prevented (Image 1). Reputed forgers of largest crank shafts in India use this

technique.

2. Reduction in Acid Pickling Time of SS Bars and Shot Blasting Time After Heat Treatment


Operations like shot blasting, grinding, acid pickling, etc., do not add value, are expensive andtime consuming procedures. These operations are necessary to remove adherent scaling from

components and to enhance aesthetic appeal of forgings. Time required for operations like shotblasting, grinding, acid pickling, etc. can be substantially reduced if protective anti scale coating is

applied on components before heat treatment. Aesthetic appeal of components is automatically

enhanced without much effort as scaling is either prevented or reduced by the use of anti-oxidationprotective coating. 3. Salvaging Fully Machined Components by Protecting During Re-heat

Treatment Often, fully machined forgings need to be re-heat treated for metallurgical reasons.However, there is no material allowance left for further scaling to take place and for subsequent

machining or shot blasting operation. In such cases, even small amount of scaling can rendercomponents to be scrapped. Use of protective anti-scale coating ensures prevention of oxidation

during re-heat treatment, hence preventing huge losses. Fully machined components can be

successfully re-heat treated without the problem of oxidation or scaling by coating them withbefore re-heat treatment. Aesthetic appeal of components is retained (Image 2). Coating itself can

be removed after heat treatment by cleaning the forgings with diesel, emery paper brushing or light

wire brushing.

4. Heat Treatment of Pressure Vessels

Valve areas and machined areas of pressure vessels are critical and need to be protected fromscaling during thermal cleaning and heat treatment. Scaling on threaded portions will cause

leakages and prove dangerous during use of such equipments. Protection of critical areas of

pressure vessels is achieved by use of anti scale coating being applied only on areas where

oxidation/scaling needs to be prevented (Image 3).

5. Salvaging of Forgings during

Re-heating for Hot ForgingRe-heating or re-working of forgings is required due to underfill,

improper metal formation and similar reasons. However, with stringent dimensional tolerances,

there is a risk of forgings getting scrapped/rejected due to excessive scaling (Image 4).


Anti-scale coating, when applied on forgings before re-heating for re-working, ensures minimal or

no scaling, thereby eliminating risk of scrapping components during re-working (Image 5).

6. Reducing Decarburisation during Hot Rolling & Hot Forging


Certain grades like spring steels, ball bearing steel and rail steel are susceptible to decarburisation.During hot rolling of these special grades, decarburisation needs to be consistently maintained to

the required specification. However, due to unforeseen conditions like mill breakdown and

unplanned downtime, billets remain in the furnace for longer time than usual.

Also, when the plant is closed for weekly holiday, furnace is shut off abruptly, subjecting the

billets to prolonged heating inside the furnace. If billets are not coated, it becomes difficult to

guarantee the consistency in the decarburisation level. Use of protective coatings on billets beforecharging them into the re-heating furnace enables to maintain the decarburisation level

consistently. This enables the hot rolling mill to guarantee their customers that decarburisation

level will always be less than the upper control limit. Reduced decarburisation on automobile leafsprings leads to increased fatigue strength of the leaf springs and greater reliability. Leaf springs

heated after applying protective coating show substantially reduced decarburisation and scaling.

7. Improving Surface Finish of Hot Rolled Components and Preventing Welding of Billets

during Heating

During hot rolling of special grades of steel like Nickel (Ni) and 416 Stainless Steel containing

high sulphur content, mill scale is greatly increased. Surface finish of hot rolled product may becompromised due to scale pits and rolled-in scale. Occasionally, due to heavy adherent scale,

problem of roll skid is also encountered. Subsequent grinding operations are increased due to

excessive mill scale. Applying anti-scale coating on billets before charging them into the re-

heating furnace ensures reduced oxidation and mill scale. Coating the billets before charging theminto the reheating furnace enables to achieve good surface finish of the hot rolled products free

from scale pits and rolled-in scale. During re-heating of billets for hot rolling and also during

induction heating of billets for hot forging, sometimes, billets are welded together. This leads tounproductive process of separating the welded billets and downtime. Welding of billets during hot

rolling and hot forging can be prevented by applying protective coating on billets before charging

them into the furnace.

8. Improving Surface Finish of Seamless Pipes and Hot Forged Components


In the manufacture of seamless pipes, machined hollow ingots are used in many places, especiallyin Poland. It becomes a necessity to protect the surface by protective coating when the ingot is

reheated. This ensures better surface finish of the seamless pipe. It is very essential to minimise thescaling in precision forgings like headed bolts. This can be done by the use of anti-scale protective

coatings.

Summary

1. Use of protective coatings is established as an effective technique of preventing

oxidation/scaling and decarburisation during heat treatment, hot forging and hot rolling.2. It has unleashed a number of additional benefits like ability to salvage by re-heat treatment,

elimination of post-heat treatment operations like grinding, shot blasting, acid pickling, etc.3. The coating process has simplified and accelerated many metallurgical heat treatment

operations, saving a fortune in capital investment, reducing costs and improving quality.

Cost Reduction in Heat Treatment With Protective Coatings

Documents

Transcript of Cost Reduction in Heat Treatment With Protective Coatings