Corrosive fume exhaust pipe, stainless steel duct and vent ... · Stainless Steel Corrosive Fume...
Transcript of Corrosive fume exhaust pipe, stainless steel duct and vent ... · Stainless Steel Corrosive Fume...
Stainless Steel Corrosive FumeExhaust Systems WithPermaShield FluoropolymerBarrier Coating
PRODUCT CATALOG
Catalog 01/19.2
®
PermaShield Pipe
Fab-Tech, Inc.A Critical Process Systems Group Company
C
CONTENTS PRODUCT CATALOG
REV: 12/01/19 CAT002EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
2®
®PermaShield Pipe (PSP ) Ductwork Fabrication StandardsStraight Duct GaugeRing Mechanical SpecificationsRing Mechanical Specifications
Straight DuctStraight Duct with Fab-Tech Flange ( Use with 2" & 3" PSP-EZ™ Fittings )Straight Duct with Straight TapStraight Duct with Conical TapStraight Duct with Shoe Tap
Straight Duct with Multiple TapsGored ElbowReducerOffset
AMCA Damper Test Setup
50" & Larger Reinforced Heavy Duty Industrial Damper24" - 84" Ultra Series Industrial Damper
4" - 36" Horizontal Run Isolation Blastgate
38" & Larger Horizontal Run Isolation Blastgate
4" - 36" Vertical Run Isolation Blastgate
38" & Larger Vertical Run Isolation Blastgate
4567
1718192021
23242526
35
38
40
44
4647
STANDARDS
DUCT & FITTINGS
CONTROL DEVICES
4" - 12" Wafer Isolation Damper
31
PSP-EZ™ Clamp Mechanical Specifications 9
Straight Duct with Lateral Tap 22
51
49
16
30
2" & 3" Micro-Adjustable EZ Damper
32
6" - 14" AMCA Industrial Isolation Damper
36
Custom Fitting 29Concentric Round to Rectangular Transition 28
6" - 14" Industrial Isolation Damper39
43
T
W
DUCTDIA"D"
H
2" & 3" EZ Blastgate48
Intentionally Left Blank
33
4" Industrial Isolation Damper
34
End Cap 27
16" - 36" Horizontal Run Actuated Isolation Blastgate50
38" & Larger Horizontal Run Actuated Isolation Blastgate52
16" - 36" Vertical Run Actuated Isolation Blastgate
38" & Larger Vertical Run Actuated Isolation Blastgate
16" - 48" High Value Heavy Duty Industrial Damper (HVD)42
4" - 14" Industrial Isolation Short Damper
37
4116" - 34" AMCA High Value Heavy Duty Industrial Damper
4536" - 48" AMCA High Value Heavy Duty Industrial Damper
PRODUCT GUIDE
PRODUCT GUIDE
Round Damper Comparison Chart
Metric Conversion Chart
53
Weight Chart EZ Duct / Miscellaneous FittingsWeight Chart Straight Duct & Elbows: -6 Pressure ClassWeight Chart Straight Duct & Elbows: -10 Pressure ClassWeight Chart Straight Duct & Elbows: -14 Pressure Class
Round Damper Comparison Chart
54
Round Damper Comparison Chart
55
Weight Chart Straight Duct & Elbows: -18 Pressure Class
1112131415
10
Gasket Placement For Dissimilar Duct Joint Connections 8
CONTENTS PRODUCT CATALOG
REV: 12/01/19 CAT003EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
3®
EZ Straight Duct, Tee and Reducing TeeEZ Double Tee, Lateral, 90° ElbowEZ 45° Elbow, 30° Elbow, Eccentric ReducerEZ Concentric Reducer, Angle Ring to EZ Reducer, End CapMicro-Adjustable EZ DamperField Installed Straight Duct EZ Flange
Fab-Tech FlangeKF Flange AdapterNPT Male Nipple AdapterNPT Female Coupler Adapter
®SWAGELOK AdapterDwyer Pitot AdapterSprinkler AdapterField Installed 2" Fab-Tech FlangeField Installed Fab-Tech Flange Saddle Tap
697071
727374
7778798081
82838484
FAB-TECH FLANGE SYSTEM
EZ FITTINGS
EZ Blastgate
75
Mounting Flange StandardsStraight DuctStraight Duct with Straight Rectangular TapStraight Duct with Rectangular Boot TapStraight Duct with Rectangular Conical TapStraight Duct with Rectangular Lateral TapStraight Duct with Round TapStraight Duct with Multiple Taps90°, 60°, 45°, 30° or Custom Elbow
858686878888898990
RECTANGULAR DUCT
90°, 60°, 45°, 30° or Custom Mitered ElbowConcentric TransitionConcentric Rectangular to Round TransitionOffsetDouble OffsetEnd Cap
Industrial Parallel Blade Control DamperIndustrial Opposed Blade Control Damper
Horizontal Blastgate
9191
929394
9696
Vertical Blastgate
94Industrial Backdraft Damper
97
68
76
85
RECTANGULAR CONTROL DEVICES PRODUCT GUIDE
95Heavy Duty Parallel Blade Control DamperHeavy Duty Opposed Blade Control Damper
6667
65
PRODUCT GUIDE
PRODUCT GUIDE
PRODUCT GUIDE 64
Rectangular Damper Comparison Chart
97
58
5657
59
6263
Field Installed Nipple / Test PortField Installed Saddle TapField Installed Hot Tap
61
ACCESSORIESField Installed Nipple
60
PRODUCT GUIDE
PSP-EZ™ Clamp KitAngle RingCast Ring
Fab-Tech reserves the rightto change or modify specifications without notice.
®PSP and PSP-EZ™ are registered trademarks of Fab-Tech, Inc.
Visit our website at www.fabtechinc.comEmail address: [email protected]
The Fab-Tech Ductwork Fabrication Standard Manual is designed to aid you, our customer, in becoming acquainted with our fabrication practices. The manual is in strict accordance with the practices in the latest S.M.A.C.N.A. manuals.
GENERAL
Codes and Standards
a. Ducts shall be listed for use without the necessity for internal fire protection sprinklers or any devices relied on to cut off air flow in the event of fire by the following:
Factory Mutual Research Standard 4922
Limitations and Requirements:
1. All ducts shall be interiorly furnished with a fluoropolymer thermoplastic resin. The total interior coating thickness shall
coverage is required.not exceed 16 mils (0.30 mm). Complete and uniform coating
2. This duct may be used for smoke removal in special purpose areas when properly designed and sized. Sprinklers are not required.
3. The product shall be manufactured with identical resins as tested, and according to the formulation on file with FMRC, and shall meet all physical requirements of S.M.A.C.N.A. manual for Industrial Duct Construction Standards.
4. Vertical height of individual risers within the duct systemare not restricted, however, they shall not penetrate other fire areas.
5. The manufacturer shall determine the suitability of the duct systems for specific corrosive environments.
6. If the process served by such duct system produces flammable residue or a combustible fume source exceeding
2 21ft (0.09 m ) in area per inlet which can build up inside the duct, then internal sprinklers will be required.
7. ASTM E-84 Standard Test Method for Surface Burning Characteristics. Tested in flat sheet form at a 20 ga. (0.95 mm) thickness: Flame Spread 0, Smoke Density 20.
DUCTWORKa. Base Metal shall be a series 300 Stainless Steel. Longitudinal seams shall be fusion welded. Traverse seams shall be continuous weld. All seams shall be smooth on the interior of duct.
b. Coating shall be PermaShield Fluoropolymer Barrier Coating andshall be applied per Factory Mutual Research Corporation's
d. Testing shall be performed at the factory over the entire coated surface inside and out (where applicable) and edges. The testing shall be performed with a DC spark tester used at 2500 volts.
e. Delivery, Storage, and Handling:
1. Protection: Protection is factory applied to ends of ductwork to prevent end damage and prevent dirt and moisture from entering ducts and fittings.
2. Delivery: Consignee must inspect shipment upon delivery and note any and all damages and discrepancies on Bill of Lading and notify manufacturer within 24 hours.
3. Storage: Coated ductwork should not be stored in an area where it will have a chance to be damaged from traffic or debris. All coated ductwork should be stored on cardboard,Styrofoam or similar materials. Where possible, store insideand protect from dirt and debris. Where necessary to storeoutside, store above ground and enclose with water proofwrapping to protect from dirt and debris.
4. Handling: If coating is scratched use appropriate protocol to "spark test" (refer to Installation and Assembly Guide, Field Modification section) and if spark is detected, contact manufacturer for repair instruction.
e. Duct Assembly shall be accomplished utilizing either companionrings or Fab-Tech's PSP-EZ™ clamp:
1. Companion rings are available as angle rings in sizes 4" thru120” diameter or as cast rings in sizes 4” thru 14” diameter. The
each 4" of duct circumference to the next higher number.
2. PSP-EZ™ clamps are available in sizes 2" thru 14". ThePSP-EZ™ band ring style of joining system shall provide aminimum compression load to the gasket of 900 PSI.
f. Gasket Technology:
1. Ring gasket material shall be form in place, fully expanded100% PTFE rope joint sealant.
2. PSP-EZ™ clamp gasket material shall be form in place,fully expanded 100% PTFE tape or die cut gasket
b. Fab-Tech's FM Global Approval ( 4922 ) extends the widestpossible limits from 4" diameter ( 100mm ) up to and including 60"diameter ( 1525mm ) duct and fittings.
REV: 12/01/19 CAT004EA
STANDARDS®
PermaShield Pipe (PSP ) DuctworkFabrication Standards
limitations and requirements.
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
4®
5. Welding: Under no circumstances shall welding or a heatsource greater than 300°F (150°C) be allowed on the stainlesssteel surface of the duct.
minimum number of holes for flange connections is one hole for
c. Black Iron Rings shall be coated with PermaProtect, Black IronRing Powder®. This heat and chip resistant coating is electro staticallyapplied and sintered to the substrate.
Fab-Tech, Inc.A Critical Process Systems Group Company
(2"-3" diameter).
-6"WG
-18"WG
STDDUCT
LENGTH
MIN GAUGE FOR 8' DUCT
20
20
18 95.25
16
12
18
14
16
14
12
20
18
12
14
16
10GAOR
12 GAWITH
STIFFENER
18
12
14
16
-14"WG
-10"WG
DUCTDIA -6"
WG-18"WG"D"
MIN GAUGE FOR 4' DUCT
4
20
20
68
10121416
18
1820222426283032343638404244464850
16
525456586062646668707274767880828486
18
14
16
14
889092949698
100102104106108110112114116118120
20
18
12
14
16
20
18
12
14
16
-14"WG
-10"WG
STDDUCT
LENGTH
47.25
46.75
REV: 12/01/19 CAT005EA
Straight Duct Gauge
DUCTDIA"D"
468
101214161820222426283032343638404244464850525456586062646668707274767880828486889092949698
100102104106108110112114116118120
DUCTDIA"D"
468
101214161820222426283032343638404244464850525456586062646668707274767880828486889092949698
100102104106108110112114116118120
STANDARDS
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
5®
20
94.75
Duct and fittings greater than 84" diameterrequires engineering review and approval.
Custom angle rings available on request.
See Installation and Assembly Guide for metricduct size conversions.
# H
OL
ES
BO
LT
HO
LE
SIZ
E
PTFE ROPE GASKETS* FOR RING JOINTS
4"-10"Ø
3/16" ROPEP/N: GAS01
12"-24"Ø
1/4" ROPEP/N: GAS02
26"-120"Ø& RECTANGULAR
1/4" x 3/16" ROPEP/N: GAS03
14161820222426283032343638404244464850525456586062646668707274767880828486889092949698
100102104106108110112114116118120
DU
CT
DIA
"D"
1/4x
3/16
1/4x
1/8
3/16x
1/8
9/16x
3/4
116
12
16
20
24
28
32
36
40
44
48
52
56
60
64
68
72
76
80
15.8117.6319.6321.6323.8825.8827.8829.8831.8833.8835.8837.8840.3842.3844.3846.3848.3850.3852.8854.8856.8858.8860.8862.8864.8866.8868.8870.8872.8874.8876.8878.8880.8882.8884.8886.88
112
108
104
100
96
92
88
8489.3891.3893.3895.3897.38
100.38102.38104.38106.38108.38110.38112.38114.38116.38118.38120.38122.38124.38
BO
LT
SIZ
E
BO
LT
CIR
CL
ED
IA.
PT
FE
GA
SK
ET
W x
H
WID
TH
(W)
4
2
3
TH
ICK
NE
SS
(T)
3/16
1/4
468
101214161820222426283032343638404244464850525456586062646668707274767880828486889092949698
100102104106108110112114116118120
DU
CT
DIA
"D"
Standard mounting hole locations for weldedangle rings (32" to 120") straddle the verticalcenterline unless otherwise specified.
Standard hardware provided for angle ringapplications are plated GRADE 5 fasteners.Stainless steel hardware is not recommended.
* ADHESIVE ON ONE SIDE
ANGLE RING SPECIFICATIONS
2-1/2
1-1/2
3/16" 1/4" 1/4"
3/16"
Torque in at least 3 stagesTorque Specifications:
REV: 12/1/19 CAT006EC
FL
OA
T
SS
ST
AIN
LE
SS
ST
EE
L
FL
OA
T
BI
BL
AC
KIR
ON
FL
OA
T
SC
RING MATERIAL& GASKETS
Duct 4" to 14" manufactured with cast ringsas standard. Duct 16” to 120" manufacturedwith angle rings as standard.
Notes:
Grade 5 Bolt Markings:
STANDARDS
Ring Mechanical Specifications
# H
OL
ES
BO
LT
HO
LE
SIZ
E
468
10
DU
CT
DIA
"D"
3/87/16
x11/16
6
8
12
5.317.509.5011.50
BO
LT
SIZ
E
BO
LT
CIR
CL
ED
IA.
WID
TH
(W)
1-1/4
HE
IGH
T(H
)
13/32
CAST RING SPECIFICATIONS
1-1/2 1/2 1/29/16
x3/4
TH
ICK
NE
SS
(T)
1/8
3/16
SC
SS
BI BLACK IRON ANGLE RING
STAINLESS STEEL ANGLE RING
STAINLESS CAST RINGKEY:
468
1012
3/87/16x
11/16
6
8
5.317.509.5011.5013.81
1-1/41/8
13.81
15.81
12
14
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
6®
1 7/16
SLOT1/2
DuctDia.
BoltSize
4"-10" 3/8"
Ft lb In lb Nm
12"-120" 1/2"
35 420 48
65 780 88
ST
ITC
H W
EL
DE
D
SS
ST
ITC
H W
EL
DE
D
BI
T THICKNESS (SEE RING SPEC CHART)
W
DUCTDIA"D"
W WIDTH (SEE RING SPEC CHART)
ANGLE RINGBLACK IRON OR
STAINLESS STEEL GRADE 5FASTENERS
DUCTPTFEGASKET
STAINLESS STEELCAST RING
DUCT PTFEGASKET
GRADE 5FASTENERS
T THICKNESS (SEE RING SPEC CHART)
W
DUCTDIA"D"
H HEIGHT (SEE RING SPEC CHART)
DUCT
Ring Mechanical Specifications
REV: 12/01/19 CAT007EB
Angle RingCast RingBLACK IRON ANGLE RING 4" TO 100"STANDARD FOR DUCT 4" TO 14"
DUCT
RINGWIDTH
RINGWIDTH
STANDARDS
STAINLESS STEEL ANGLE RING 16" TO 120"
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
7®
ANGLE RINGBLACK IRON OR
STAINLESS STEEL
DUCT
STITCH WELDS
PTFE GASKET
Floating Angle Ring
Stitch Welded Angle Ring
Floating Cast Ring
Gasket Placement For Dissimilar Duct Joint Connections
REV: 12/01/19 CAT008EB
STANDARDS
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
8®
ANGLE RINGBLACK IRON OR
STAINLESS STEEL
FLEX BODYFROM OTHERMANUFACTURER
DUCT
GASKET (BY OTHERS)W/ NO OR VERY LITTLECOMPRESSIVE LOAD
STANDARD DUCTCONSTRUCTION
W/ TURNED FLANGE
Incorrect Flex/Expansion Joint Connection
BACKING RING
HARDWARE & GASKET( FROM OTHERS )
ANGLE RINGBLACK IRON OR
STAINLESS STEEL
DUCT
GASKET POSITIONEDCLOSER TO BOLTHOLES FOR BETTERCOMPRESSIVE LOAD
CUSTOM DUCTCONSTRUCTIONFULLY WELDED
FLANGE W/COATED FACE
FULLWELD
Correct Gasket Placement For Dissimilar Duct Joint Connections
ANGLE RINGBLACK IRON OR
STAINLESS STEEL
DUCT
GASKET (BY OTHERS)W/ NO OR VERY LITTLECOMPRESSIVE LOAD
STANDARD DUCTCONSTRUCTION
W/ TURNED FLANGE
Incorrect FRP or Other Duct Joint Connection
FRP OR OTHER DUCT
HARDWARE & GASKET( FROM OTHERS )
FRP OROTHERDUCT
FULLWELD
GASKET POSITIONEDAT I.D. OF ADJOININGDUCT
DUCT
468
101214
20
-6" Thru -18"WG
DUCT GAUGE
"D"
STRAIGHTDUCT
LENGTH
4 FT( 47.25"
ACTUAL )
BACKINGRING
WELDED
FLOATING
23
.035 TUBING
DUCTDIA.
"D"
CLAMP
PSP-EZ™ Clamp Mechanical Specifications
REV: 12/01/19 CAT009EB
CROSS SECTION OF JOINT
The PSP-EZ™ joining system is available for® standard PSP duct from 2" to 14" in diameter.
The combination of half round backing ringsand the unique angled clamp band providesexcellent clamping force with the addedbenefit of ease of installation.
CLAMP
DUCTDUCT
DUCTFLANGE
CROSS SECTION OF JOINT
DUCTFLANGE
2" & 3" PSP-EZ™ CLAMP 4"-14" PSP-EZ™ CLAMP
DUCT
STANDARDS
CLAMP
FLOATINGBACKING
RING
DUCTDUCT
FLOATINGBACKING
RING
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
9®
DuctDiameter
BoltSize
Torque Specifications:Torque in at least
3 stages
8",10",12",14" 5/16"
lb*ft lb*in kg*m
6.25 75 0.9
10 120 1.4
4",6" 1/4"
.065 TUBING
Conversion Chart - Imperial to Metric
REV: 12/01/19 CAT010EB
DUCT & FITTINGS
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
10®
DUCT AND FITTINGS GREATER THAN 84" DIAMETER REQUIRES ENGINEERING REVIEW AND APPROVAL
METRIC CONVERSIONS ARE ROUNDED TO THE MOST APPROPRIATE EVEN INCH UNLESS OTHERWISE SPECIFIED
EnglishEquivalent
EnglishEquivalent
OrderSize
OrderSize
ActualSize
ActualSize
DUCT DIA DUCT DIA
4"
62"
100mm
1550mm
101.6mm
1574.8mm2"
60"
50mm
1500mm
50.8mm
1524.0mm
6"
64"
150mm
1600mm
152.4mm
1625.6mm
8"200mm
1650mm
203.2mm
10"
68"
250mm
1700mm
254.0mm
1727.2mm
12"
70"
300mm
1750mm
304.8mm
1778.0mm
14"
72"
350mm
1800mm
355.6mm
1828.8mm
16"
74"
400mm
1850mm
406.4mm
1879.6mm
18"
76"
450mm
1900mm
457.2mm
1930.4mm
20"
78"
500mm
1950mm
508.0mm
1981.2mm
22"
80"
550mm
2000mm
558.8mm
2032.0mm
24"
82"
600mm
2050mm
609.6mm
2082.8mm
26"
84"
650mm
2100mm
660.4mm
2133.6mm
28"
86"
700mm
2150mm
711.2mm
2184.4mm
30"
88"
750mm
2200mm
762.0mm
2235.2mm
32"
90"
800mm
2250mm
812.8mm
2286.0mm
34"
92"
850mm
2300mm
863.6mm
2336.8mm
36"
94"
900mm
2350mm
914.4mm
2387.6mm
38"
96"
950mm
2400mm
965.2mm
2438.4mm
40"
98"
1000mm
2450mm
1016.0mm
2489.2mm
42"
100"
1050mm
2500mm
1066.8mm
2540.0mm
44"
102"
1100mm
2550mm
1117.6mm
2590.8mm
46"
104"
1150mm
2600mm
1168.4mm
2641.6mm
48"
106"
1200mm
2650mm
1219.2mm
2692.4mm
50"
108"
1250mm
2700mm
1270.0mm
2743.2mm
52"
110"
1300mm
2750mm
1320.8mm
2794.0mm
54"1350mm 1371.6mm
56"1400mm 1422.4mm
58"1450mm 1473.2mm
112"2800mm 2844.8mm
114"2850mm 2895.6mm
116"2900mm 2946.4mm
118"3950mm 2997.2mm
120"3000mm 3048.0mm
66” 1676.4mm
REV: 12/01/19 CAT011EB
DUCT & FITTINGS
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
11®
®Weight Chart - PSP Coated EZ Duct / Miscellaneous Fittings
DUCTDIA
468
101214161820222426283032343638404244464850525456586062646668707274767880828486889092949698
100102104106108110112114116118120
Blastgatew/ Van Stone
RingsManual
Operation
Damperw/ Van
Stone RingsManual
Operation
4.98.2
10.813.722.126.310010911812813815817018219423422123524926428029631451754457360263372575779182686189793697210101051108911291171
9.814.318.222.432.137.542.858.665.272.680.298.3107117127136146326337353370385406460483505530553652672696720750800816832848864885902923
SingleVan Stone
Ring
1.01.82.32.96.97.18.08.99.8
10.811.717.418.719.921.222.523.825.026.327.628.930.131.441.443.144.646.347.879.582.084.687.189.792.994.897.4100102105108110113115118120123171174178181185188192195199202206209213
EndCap
w/ VanStoneRing
1.32.43.24.28.79.4
15.117.620.222.925.833.637.240.844.648.560.064.669.474.379.484.689.9120126133
207216225235244254263273283293304314325336347358369380437450463475488502515528542555569583598
468
101214
7.210.914.518.121.725.5
2.24.58.311.915.121.7
1.22.44.06.08.511.3
DUCTDIA 4’ Duct
90° Elbow 60° Elbow
0.40.61.21.41.82.0
SingleClamp
0.81.72.94.36.07.9
1.53.56.49.0
10.916.0
3.14.86.48.1
10.312.6
Damper
7.09.5
12.715.017.921.0
Blastgate
1.01.62.63.54.45.4
EndCap
468
101214
DUCTDIA
468
101214
DUCTDIA
1.82.73.64.55.46.3
DuctPer Foot
R=1.5D R=1DR=1.5D R=1D
0.91.93.14.76.68.8
45° Elbow
0.71.42.33.44.76.3
30° Elbow
0.41.01.72.73.44.5
0.61.42.33.84.76.2
468
101214
DUCTDIA R=1.5D R=1D R=1.5D R=1D
NOTES:
1. ALL WEIGHTS ARE CALCULATED, HARDWARE NOT
2. SOME WEIGHTS FOR FITTINGS LARGERTHAN 20” DIAMETER HAVE BEEN ROUNDEDTO THE NEAREST POUND.
EZ Duct Weight Charts
3. TO CALCULATE THE APPROXIMATE WEIGHT FORCUSTOM LENGTH DUCT OR FOR FITTINGS SUCHAS REDUCERS, USE THE PER FOOT WEIGHT FORSTRAIGHT DUCT IN THE PROPER PRESSURECLASS.
140147
INCLUDED.
30° Elbow
3.06.09.2
12.321.527.633.739.845.952.059.4778796
128141154167179195211227245281301373397421508536565596627658691859898937976
2.65.07.49.7
17.722.026.430.735.139.444.760677393
102111120125135146156167197209249264279356374392412432451472564588612636
3.47.0
10.714.425.333.241.149.056.964.874.595
1071201641811982152342562783003253683944985305676647037437858288719161159121312671321
R=1.5D
2.85.58.2
10.919.624.830.035.240.445.652.0697785111122133144152165178191206239255310329350431454478503529554581707738769800
DUCTDIA
468
101214161820222426283032343638404244464850525456586062646668707274767880828486889092949698
100102104106108110112114116118120
R=1D
2.34.96.99.0
16.820.724.628.532.436.342.75763708593
101109119128138149159188199229242267342360377395414432452524546568590
2.95.98.911.921.026.832.638.444.250.057.6758493
123135147159174189205222238274292364387412497525553583613643675834871908945
R=1.5D R=1D
2.65.37.7
10.118.523.227.932.737.442.147.6637078
101111121131137148161173185216230279296315393414435457480502525634661688715
2.14.66.48.4
15.819.222.426.029.733.637.851576276839097
101109116125133160185197208220292306320334349364418445463481499
R=1.5D R=1D R=1.5D R=1D
®Weight Chart - PSP Coated Straight Duct & Elbows:
-6 Pressure Class
45° Elbow 60° Elbow 90° Elbow
9.014.218.823.635.239.244.650.055.461.065.781879399
105111117124130137143150190197204211218286295304313322333340350359367434448460474486500512526630644660674690704720734750764780858874
4’ Ductw/ VanStoneRings
8’ Ductw/ VanStoneRings
73.182.191.1
100.3108.0126136146187198211222232243253264274302440459478497577598619640661684703746768788810832852874894916936958
1070109211161138116211841208157816101640167217021734
Per Foot1' - 4'
1.72.63.54.45.36.27.18.08.99.8
10.611121314151617181920212227282930313233343536373839404156586062646668707274767880828486889092110112
32.941.356.564.1
Per Foot4' - 8'
3.54.45.36.27.18.08.99.8
10.611121318192021222324252627444648505254565860626469717375777981838587899193959799
101103149152155158161164
REV: 12/01/19 CAT012EB
DUCT & FITTINGS
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
12®
®Weight Chart - PSP Coated Straight Duct & Elbows:
-10 Pressure Class
30° Elbow
3.06.09.212.321.527.633.739.845.952.059.4778796
128141154167179195211227245281349373397421508536565596627658820859898937976
2.65.07.49.7
17.722.026.430.735.139.444.760677393
102111120125135146156167197234249264279356374392412432451540564588612636
3.47.0
10.714.425.333.241.149.056.964.874.595
10712016418119821523425627830032536846649853056766470374378582887111051159121312671321
R=1.5D
2.85.58.2
10.919.624.830.035.240.445.652.0697785111122133144152165178191206239291310329350431454478503529554676707738769800
DUCTDIA
468
101214161820222426283032343638404244464850525456586062646668707274767880828486889092949698
100102104106108110112114116118120
R=1D
2.34.96.99.0
16.820.724.628.532.436.342.75763708593
101109119128138149159188216229242267342360377395414432502524546568590
2.95.98.911.921.026.832.638.444.250.057.6758493
123135147159174189205222238274341364387412497525553583613643797834871908945
R=1.5D R=1D
2.65.37.7
10.118.523.227.932.737.442.147.6637078
101111121131137148161173185216262279296315393414435457480502607634661688715
2.14.66.48.4
15.819.222.426.029.733.637.851576276839097
101109116125133160186197208220292306320334349364427445463481499
R=1.5D R=1D R=1.5D R=1D
45° Elbow 60° Elbow 90° Elbow
9.014.218.823.635.239.244.650.055.461.065.781879399
105126133139146153159166190197204211279351364377390403418429443456468482496524538550564576590694708724738754768784798814828844858874
4’ Ductw/ VanStoneRings
8’ Ductw/ VanStoneRings
73.182.191.1
122.4133.4154163177187198273292310329348366385421440481500519599620641662683705725746768
1008103810681096112611541184121212421362139214241454148615161548157816101640167217021734
Per Foot1' - 4'
1.72.63.54.45.36.27.18.08.99.8
10.61112131415202122232425262728293046485052545658606264666870767880828486889092949698
100102104106108110112
32.941.356.564.1
Per Foot4' - 8'
3.54.45.36.27.18.08.9
12.613.71516171819283032343638404244495153555759616365676971
101104107110113116119122125128131134137140143146149152155158161164
DUCT & FITTINGS
REV: 12/01/19 CAT013EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
13®
®Weight Chart - PSP Coated Straight Duct & Elbows:
-14 Pressure Class
30° Elbow
3.06.09.2
12.321.527.633.739.845.952.059.477
102115128141154167179195211267287325349373397421508536565596742781820859898937976
2.65.07.49.7
17.722.026.430.735.139.444.760758493
102111120125135146178191219234249264279356374392412492516540564588612636
3.47.0
10.714.425.333.241.149.056.964.874.595
130147164181198215234256278357384434466498530567664703743785997
105111051159121312671321
R=1.5DDUCTDIA
468
101214161820222426283032343638404244464850525456586062646668707274767880828486889092949698
100102104106108110112114116118120
R=1D
2.34.96.99.0
16.820.724.628.532.436.342.75769778593
101109119128138161172203216229242267342360377395458480502524546568590
2.95.98.911.921.026.832.638.444.250.057.67599111123135147159174189205259278318341364387412497525553583723760797834871908945
R=1.5D R=1D
2.65.37.7
10.118.523.227.932.737.442.147.6638191
101111121131137148161198212245262279296315393414435457553580607634661688715
2.14.66.48.4
15.819.222.426.029.733.637.851626976839097
101109116138147175186197208220292306320334391409427445463481499
R=1.5D R=1D R=1.5D R=1D
45° Elbow 60° Elbow 90° Elbow
9.014.218.823.635.239.244.650.055.461.065.78110
107113120126133139146153196207235246257268279351364377390420434446459472484498516524538550564576590694832852870890908928946966984
100410221042
4’ Ductw/ VanStoneRings
8’ Ductw/ VanStoneRings
73.182.1111.2122.4133.4154163218236255273292310351369388406442462481500519599776806835864894922951980
1008103810681096112611541184121212421362139214241454148615161548178018201858189819361976
Per Foot1' - 4'
1.72.63.54.45.36.27.18.08.99.8
10.6111617181920212223243436384042444648505254606264666870727476788082848688
121124127130133136139142145148151154
32.941.356.564.1
Per Foot4' - 8'
3.54.45.36.27.18.011.412.613.71516222426283032373941434547495153557780838689929598
101104107110113116119122125128131134137140143146174178182186190194
2.85.58.2
10.919.624.830.035.240.445.652.06989
100111122133144152165178221237272291310329350431454478503614645676707738769800
DUCT & FITTINGS
REV: 12/01/19 CAT014EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
14®
®Weight Chart - PSP Coated Straight Duct & Elbows:
-18 Pressure Class
30° Elbow
3.06.09.2
12.321.527.633.739.845.952.069.589
102115128141154167207227247267287325349373397494586625664703742781820859898937976
2.65.07.49.7
17.722.026.430.735.139.449.966758493
102111120139152165178191219234249264317396420444468492516540564588612636
3.47.0
10.714.425.333.241.149.056.964.889.5113130147164181198215276303330357384434466498530676781835889943997
105111051159121312671321
R=1.5D
2.85.58.2
10.919.624.830.035.240.445.659.77889
100111122133144173189205221237272291310329405490521552583614645676707738769800
DUCTDIA
468
101214161820222426283032343638404244464850525456586062646668707274767880828486889092949698
100102104106108110112114116118120
R=1D
2.34.96.99.0
16.820.724.628.532.436.346.06169778593
101109128139150161172203216229242293370392414436458480502524546568590
2.95.98.911.921.026.832.638.444.250.067.78799111123135147159202221240259278318341364387485575612649686723760797834871908945
R=1.5D R=1D
2.65.37.7
10.118.523.227.932.737.442.154.4718191
101111121131156170184198212245262279296364445472499526553580607634661688715
2.14.66.48.4
15.819.222.426.029.733.641.755626976839097111120129138147175186197208246319337355373391409427445463481499
R=1.5D R=1D R=1.5D R=1D
45° Elbow 60° Elbow 90° Elbow
9.014.218.823.635.239.244.650.055.461.078.194
100107133120126133164175186196207235
257268296367380394407420434446459472484498512620638654672688706814832852870890908928946966984
100410221042
4’ Ductw/ VanStoneRings
8’ Ductw/ VanStoneRings
72.80100.2111.2122.4133.4181199218236255295314332351369388406442
606633660747776806835864894922951980
1008103810681096112611541184121213801508154615861624166417021742178018201858189819361976
Per Foot1' - 4'
1.72.63.54.45.36.27.18.08.99.8
13.715161718192021283032343638
424450525456586062646668707274
100103106109112115118121124127130133136139142145148151154
32.941.356.564.1
Per Foot4' - 8'
3.54.45.36.29.1
10.311.412.613.718202224263133353739414345
656871747780838689929598
101104107110113116119122142146150154158162166170174178182186190194
246 57940 62
DUCT & FITTINGS
REV: 12/01/19 CAT015EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
15®
4" to 120" DUCT
STRAIGHT DUCT
PAGE:17SIZE:4"-120"
GORED ELBOW30°, 45°, 60°, 90°
PAGE:24SIZE:
CONCENTRICREDUCER
PAGE:25SIZE:6"-120"
ECCENTRICREDUCER
PAGE: 25SIZE:6"-120"
OFFSET
PAGE:26SIZE:4"-120"
4"-120"
STRAIGHT DUCTWITH CONICALTAP
PAGE: 20SIZE:6"-120"
STRAIGHT DUCTWITH STRAIGHTTAP
PAGE:19SIZE:6"-120"
STRAIGHT DUCTWITH FAB-TECHFLANGE
PAGE: 18SIZE: 2", 3”
STRAIGHT DUCTWITH MULTIPLETAPS
PAGE: 23SIZE:4"-120"
STRAIGHT DUCTWITH LATERALTAP
PAGE:22SIZE:6"-120"
STRAIGHT DUCTWITH SHOE TAP
PAGE:21SIZE:6"-120"
Product Guide
REV: 12/01/19 CAT016EB
DUCT & FITTINGS
4" to 14"PSP-EZ™ CLAMP
STRAIGHT DUCT
PAGE:17SIZE:4" TO 14"
CONCENTRICREDUCER
PAGE: 25
ECCENTRICREDUCER
PAGE: 25SIZE: 4" TO 14"
OFFSET
PAGE:26SIZE:4" TO 14"
STRAIGHT DUCTWITH SHOETAP
PAGE:21SIZE:6" TO 14"
STRAIGHT DUCTWITH CONICALTAP
PAGE: 20SIZE:6" TO 14"
STRAIGHT DUCTWITH STRAIGHTTAP
PAGE: 19SIZE: 4" TO 14"
GORED ELBOWS30°, 45°, 60°, 90°
PAGE:24
STRAIGHT DUCTWITH MULTIPLETAPS
PAGE: 23
STRAIGHT DUCTWITH LATERALTAP
PAGE: 22SIZE:4" TO 14" SIZE: 4" TO 14" SIZE: 4" TO 14"
SIZE: 4" TO 14"
STRAIGHT DUCTWITH FAB-TECHFLANGE
PAGE: 18SIZE: 2", 3”
CONCENTRIC ROUNDTO RECTANGULARTRANSITION
PAGE:28
CUSTOM FITTING
PAGE: 29
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
16®
CONCENTRIC ROUNDTO RECTANGULARTRANSITION
PAGE:28
CUSTOM FITTING
PAGE: 29
END CAP
PAGE: 27
SIZE:4"-120"
END CAP
PAGE:27SIZE:4" TO 14"
REV: 12/01/19 CAT017EB
OPTIONS:
Custom lengths available.
Refer to FAB-TECH FLANGE SYSTEM section for adapters, drains andtest ports.
Raw end available.
Duct greater than 84" diameter requires Engineering review and approval.
"L"
"D"
All fittings with standard Fab-Tech connections include gaskets and clampsor hardware as required for installation.
NOTES:
DUCT & FITTINGS
Straight Duct
LONGER THAN STANDARD LENGTHS AND/OR HIGHER SYSTEM PRESSURESMAY REQUIRE ADDITIONAL STIFFENERS PER SMACNA, CONTACT FAB-TECHFOR SPECIFIC GUIDELINES.
4" - 14"
4" - 14"
SS CAST RING
EZ CLAMP
4" - 120"
16" - 120"
BI ANGLE RING
SS ANGLE RING
OR A COMBINATION OFJOINING SYSTEMS
WITH JOINT SYSTEM
-6"WG
-10"WG
-14"WG
MIN GAUGEFOR 8' DUCT
20
16
18
14
12
20
18
12
14
16
18
12
14
16
10
DUCTDIA -6"
WG-10"WG
-14"WG"D"
MIN GAUGEFOR 4' DUCT
4
20
68
101214161820222426283032343638404244464850
16
525456586062646668707274767880828486
18
14
889092949698
100102104106108110112114116118120
20
18
14
16
20
18
12
14
16
See Duct Gauge chart in STANDARDS section for other duct pressures.
"D"
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
17®
20
See INSTALLATION AND ASSEMBLY GUIDE for shortening 4" thru 22"duct in the field.
20
18
12
14
16
-18"WG
-18"WG
18
12
14
16
10
20
STANDARD DUCT LENGTHS ( "L1" )
8" TO 14"
47.25"BLACK IRONANGLE RING
4" & 6"
50" TO 120"
DIAMETER"L1"
JOINT SYSTEM"L1"
( 4' ) ( 8' )
47.25"
46.75"
STAINLESSANGLE RING 50" TO 120"
95.25"
94.75"
94.75"
16" TO 48"
4" & 6" 47.25"EZ CLAMP /CAST RING 95.25"
46.75"
47.25"8" TO 48" 95.25"
NA
NA
47.25"
REV: 12/01/19 CAT018EB
EZ
DUCT
FAB-TECH FLANGE( WELDED TO DUCT )
CLAMP
FAB-TECHFLANGE
ADAPTEROR PSP-EZ™DUCT
"L"
DUCT
"L"
"D"
FTFL2
PART NO. DESCRIPTION
2"
"D"
FTFL3 3" FT FLANGE 3"
.75"
.75"
"L"
2" FT FLANGE
OUR RECOMMENDATION IS TO ADD TAPS TOSTANDARD 4' AND 8' STRAIGHT DUCT WHENPOSSIBLE - TAP DIMENSIONS SHOWN ARE MINS
"D1" "D2"
SEE FAB-TECH FLANGE SYSTEM SECTION FORADAPTERS AND THE EZ FITTINGS SECTION FORDUCT TO USE WITH THE FAB-TECH FLANGE.FAB-TECH FLANGE / TEST PORT MAY BE INSTALLEDON FITTINGS OTHER THAN STRAIGHT DUCT ( USECUSTOM ORDER SHEET ).
0°
90°
270°
180°
SPECIFYPORT/DRAIN
LOCATIONANGLE
FROM 0° EZ3/4" STD
2" - FTFL23" - FTFL3
SPECIFY LOCATIONFROM "D1" END
VIEW OF "D1" DUCT END
T.O.D.
3" MAX
4"MIN
DUCT & FITTINGS
Straight Duct with Fab-Tech Flange
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
18®
STRAIGHT TAP
"D1" = 4" - 94": 4" MIN"D1" = 96" - 120": 5" MIN
"L1" MIN = "D3" + 8""L1" MAX = 96-1/4"
"D3" MAX = 88"
STRAIGHT TAP GREATER THAN 88" [ "D3" ]REQUIRES 2 PIECE DESIGNAND ENGINEERING REVIEW
"L1"
"L2"
4" MIN
"D1" "D2"
4" MIN**
MIN DISTANCE TO DUCT END
6" STD"L3"
"D3"
DUCT & FITTINGS
Straight Duct with Straight Tap
REV: 12/01/19 CAT019EB
0°
90°
270°
180°
SPECIFY TAPLOCATION ANGLE
FROM 0°
VIEW OF "D1" DUCT END
"A1"
T.O.D.
0°
90°
"L4"OFFSET
"L3" "L5"
HORIZ.
OFFSETVERTICAL
B A
DC
"D1" TAP OFFSET VIEW
OPTIONS
Custom lengths available.
Raw end available.
Duct greater than 84" diameterrequires Fab-Tech Engineeringreview and approval.
OUR RECOMMENDATION IS TO ADD TAPS TO STANDARD 4' AND 8 STRAIGHTDUCT WHEN POSSIBLE - TAP DIMENSIONS SHOWN ARE MINS
LONGER THAN STANDARD LENGTHS AND/OR HIGHER SYSTEM PRESSURESMAY REQUIRE ADDITIONAL STIFFENERS PER SMACNA, CONTACT FAB-TECHFOR SPECIFIC GUIDELINES.
Multiple and offset taps available(see the multiple tap page).
T.O.D.
4" - 14"
4" - 14"
SS CAST RING
EZ CLAMP
4" - 120"
16" - 120"
BI ANGLE RING
SS ANGLE RING
OR A COMBINATION OFJOINING SYSTEMS
WITH JOINT SYSTEM
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
19®
NOTE
All fittings with standard Fab-Techconnections include gaskets andclamps or hardware as requiredfor installation.
STANDARD DUCT LENGTHS ( "L1" )
8" TO 14"
47.25"BLACK IRONANGLE RING
4" & 6"
50" TO 120"
DIAMETER"L1"
JOINT SYSTEM"L1"
( 4' ) ( 8' )
47.25"
46.75"
STAINLESSANGLE RING 50" TO 120"
95.25"
94.75"
94.75"
16" TO 48"
4" & 6" 47.25"EZ CLAMP /CAST RING 95.25"
46.75"
47.25"8" TO 48" 95.25"
NA
NA
47.25"
CONICAL TAP
"D1" = 4" - 94": 4" MIN"D1" = 96" - 120": 5" MIN
"L1" MIN = "D3" + 10""L1" MAX = 96-1/4"
"D3" MAX = 86"
CONICAL TAP GREATER THAN 86" [ "D3" ]REQUIRES 2 PIECE DESIGNAND ENGINEERING REVIEW
"L1"
"D3"
"L2"
4" MIN
"D1" "D2"
4" MIN**
MIN DISTANCE TO DUCT END
1" STD
6"
9" STD"L3"
"C1"1" STD
DUCT & FITTINGS
Straight Duct with Conical Tap
REV: 12/01/19 CAT020EB
0°
90°
270°
180°
SPECIFY TAPLOCATION ANGLE
FROM 0°
VIEW OF "D1" DUCT END
"A1"
T.O.D.
OPTIONS
Custom lengths available.
Raw end available.
Duct greater than 84" diameterrequires Fab-Tech Engineeringreview and approval.
Multiple and offset taps available(see the multiple tap page).
OUR RECOMMENDATION IS TO ADD TAPS TO STANDARD 4' AND 8 STRAIGHTDUCT WHEN POSSIBLE - TAP DIMENSIONS SHOWN ARE MINS
LONGER THAN STANDARD LENGTHS AND/OR HIGHER SYSTEM PRESSURESMAY REQUIRE ADDITIONAL STIFFENERS PER SMACNA, CONTACT FAB-TECHFOR SPECIFIC GUIDELINES.
4" - 14"
4" - 14"
SS CAST RING
EZ CLAMP
4" - 120"
16" - 120"
BI ANGLE RING
SS ANGLE RING
OR A COMBINATION OFJOINING SYSTEMS
WITH JOINT SYSTEM
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
20®
NOTE
All fittings with standard Fab-Techconnections include gaskets andclamps or hardware as requiredfor installation.
0°
90°
"L4"OFFSET
"L3" "L5"
HORIZ.
OFFSETVERTICAL
B A
DC
"D1" TAP OFFSET VIEW
T.O.D.
STANDARD DUCT LENGTHS ( "L1" )
8" TO 14"
47.25"BLACK IRONANGLE RING
4" & 6"
50" TO 120"
DIAMETER"L1"
JOINT SYSTEM"L1"
( 4' ) ( 8' )
47.25"
46.75"
STAINLESSANGLE RING 50" TO 120"
95.25"
94.75"
94.75"
16" TO 48"
4" & 6" 47.25"EZ CLAMP /CAST RING 95.25"
46.75"
47.25"8" TO 48" 95.25"
NA
NA
47.25"
"D1" = 4" - 94": 4" MIN"D1" = 96" - 120": 5" MIN
"L1"
"D3"
"L2"
4" MIN
"D1" "D2"
4" MIN**
MIN DISTANCE TO DUCT END
6" STD
9" STD"L3"
45°
SHOE TAP
"L1" MIN = "D3" + 6" (SHOE LENGTH) + 8""L1" MAX = 96-1/4"
"D3" MAX = 86”
SHOE TAP GREATER THAN MAX "D3"REQUIRES 2 PIECE DESIGNAND ENGINEERING REVIEW
DUCT & FITTINGS
Straight Duct with Shoe Tap
REV: 12/01/19 CAT021EB
0°
90°
270°
180°
SPECIFY TAPLOCATION ANGLE
FROM 0°
VIEW OF "D1" DUCT END
"A1"
T.O.D.
OPTIONS
Custom lengths available.
Raw end available.
Duct greater than 84" diameterrequires Fab-Tech Engineeringreview and approval.
Multiple and offset taps available(see the multiple tap page).
OUR RECOMMENDATION IS TO ADD TAPS TO STANDARD 4' AND 8 STRAIGHTDUCT WHEN POSSIBLE - TAP DIMENSIONS SHOWN ARE MINS
LONGER THAN STANDARD LENGTHS AND/OR HIGHER SYSTEM PRESSURESMAY REQUIRE ADDITIONAL STIFFENERS PER SMACNA, CONTACT FAB-TECHFOR SPECIFIC GUIDELINES.
4" - 14"
4" - 14"
SS CAST RING
EZ CLAMP
4" - 120"
16" - 120"
BI ANGLE RING
SS ANGLE RING
OR A COMBINATION OFJOINING SYSTEMS
WITH JOINT SYSTEM
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
21®
NOTE
All fittings with standard Fab-Techconnections include gaskets andclamps or hardware as requiredfor installation.
0°
90°
"L4"OFFSET
"L3" "L5"
HORIZ.
OFFSETVERTICAL
B A
DC
"D1" TAP OFFSET VIEW
T.O.D.
STANDARD DUCT LENGTHS ( "L1" )
8" TO 14"
47.25"BLACK IRONANGLE RING
4" & 6"
50" TO 120"
DIAMETER"L1"
JOINT SYSTEM"L1"
( 4' ) ( 8' )
47.25"
46.75"
STAINLESSANGLE RING 50" TO 120"
95.25"
94.75"
94.75"
16" TO 48"
4" & 6" 47.25"EZ CLAMP /CAST RING 95.25"
46.75"
47.25"8" TO 48" 95.25"
NA
NA
47.25"
45° LATERAL TAP"L1" MIN = ( "D3" X 1.414 ) + 4" + "L4"
( SEE MIN LENGTH CHART ABOVE FOR "L4" )"L1" MAX = 96-1/4"
"D3" MAX = 60"
LATERAL TAP GREATER THAN 60" [ "D3" ]REQUIRES 2 PIECE DESIGNAND ENGINEERING REVIEW
0°
90°
270°
180°
SPECIFY TAPLOCATION ANGLE
FROM 0°
VIEW OF "D1" DUCT END
"A1"
T.O.D.
"L1"
"D1" "D2"
4" MIN*
6" MIN
"D3"
"L2""L3"
"L4"
4" - 48"50" - 58"60" - 94"
96" - 120"
4" MIN4" MIN5" MIN6" MIN
6" MIN7" MIN8" MIN
10½" MIN
MIN LENGTH FOR "L3" AND "L4"
"L3" "L4""D1""D1" = 4" - 94": 4" MIN"D1" = 96" - 120": 5" MIN
L2 MIN DISTANCE
4" MIN
DUCT & FITTINGS
Straight Duct with Lateral Tap
REV: 12/01/19 CAT022EB
OPTIONS
Custom lengths available.
Raw end available.
Duct greater than 84" diameterrequires Fab-Tech Engineeringreview and approval.
Multiple and offset taps available(see the multiple tap page).
OUR RECOMMENDATION IS TO ADD TAPS TO STANDARD 4' AND 8 STRAIGHTDUCT WHEN POSSIBLE - TAP DIMENSIONS SHOWN ARE MINS
LONGER THAN STANDARD LENGTHS AND/OR HIGHER SYSTEM PRESSURESMAY REQUIRE ADDITIONAL STIFFENERS PER SMACNA, CONTACT FAB-TECHFOR SPECIFIC GUIDELINES.
4" - 14"
4" - 14"
SS CAST RING
EZ CLAMP
4" - 120"
16" - 120"
BI ANGLE RING
SS ANGLE RING
OR A COMBINATION OFJOINING SYSTEMS
WITH JOINT SYSTEM
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
22®
NOTE
All fittings with standard Fab-Techconnections include gaskets andclamps or hardware as requiredfor installation.
0°
90°
"L4"OFFSET
"L3" "L5"
HORIZ.
OFFSETVERTICAL
B A
DC
"D1" TAP OFFSET VIEW
T.O.D.
STANDARD DUCT LENGTHS ( "L1" )
8" TO 14"
47.25"BLACK IRONANGLE RING
4" & 6"
50" TO 120"
DIAMETER"L1"
JOINT SYSTEM"L1"
( 4' ) ( 8' )
47.25"
46.75"
STAINLESSANGLE RING 50" TO 120"
95.25"
94.75"
94.75"
16" TO 48"
4" & 6" 47.25"EZ CLAMP /CAST RING 95.25"
46.75"
47.25"8" TO 48" 95.25"
NA
NA
47.25"
1" STD
0°
90°
270°
180°
SPECIFYTAP
ANGLEFROM 0°
AT D1END
"L2"
"L2"
"D3"
EZ3/4" STD
"D3"
"L3"6" MIN STD
2" MINFOR EZCLAMP
"L2"
"L3"
"D1"
6" STD
"L2"
"D3"
"L3"
1" MIN BETWEENANGLE RINGS
"A2" 45°STD
1/2" MINFOR ANGLE RING
"D3"CONICAL TAP
SHOE TAP
45° LATERAL TAP
FAB-TECH FLANGE ( SEE FAB-TECH FLANGE SYSTEM SECTION )
2" MINFOR EZCLAMPS
"A1"
2" OR 3"DIA.
"L3"
3" MAX
3" MAX FOR 2" & 3" TAP
"D1" TAP ANGLE VIEW
"L1"
"D2"
4"MIN
5"MIN
6"MIN
7"MIN
10½"MIN
4"-48" DUCT 50"-58" DUCT 60"-94" DUCT 96"-120" DUCT2" X 2" RINGS 2-1/2" X 2-1/2" RINGS 3" X 3" RINGS 4" X 4" RINGS
STANDARD MINIMUMS FOR 45° LATERAL AND 90° STRAIGHT TAPS:
5"MIN
6"MIN
96"-120" DUCT4" X 4" RINGS
4"MIN
6"MIN
4"MIN
8"MIN
4"MIN 4"
MIN
4"MIN
*
*
OUR RECOMMENDATION IS TO ADD TAPS TOSTANDARD 4' AND 8' STRAIGHT DUCT WHENPOSSIBLE - TAP DIMENSIONS SHOWN ARE MINS
LONGER THAN STANDARD LENGTHS AND/ORHIGHER SYSTEM PRESSURES MAY REQUIREADDITIONAL STIFFENERS PER SMACNA,CONTACT FAB-TECH FOR SPECIFIC GUIDELINES.
1" STD
"L3"
45°6"
STD6"
STD
9" STD
"L2" STRAIGHT ORBULLNOSE TAP
"D1" = 4" - 94": 4" MIN"D1" = 96" - 120": 5" MIN
MIN DISTANCE TO DUCT END
T.O.D.
DUCT & FITTINGS
Straight Duct with Multiple Taps
REV: 12/01/19 CAT023EC
OPTIONS
Custom lengths available.
Raw end available.
Duct greater than 84" diameterrequires Fab-Tech Engineeringreview and approval.
"C1"
4" - 14"
4" - 14"
SS CAST RING
EZ CLAMP
4" - 120"
16" - 120"
BI ANGLE RING
SS ANGLE RING
OR A COMBINATION OFJOINING SYSTEMS
WITH JOINT SYSTEM
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
23®
NOTE
All fittings with standard Fab-Techconnections include gaskets andclamps or hardware as requiredfor installation.
9" STD"L3"
0°
90°
"L4"OFFSET
"L3" "L5"
HORIZ.
OFFSETVERTICAL
B A
DC
"D1" TAP OFFSET VIEW
T.O.D.STANDARD DUCT LENGTHS ( "L1" )
8" TO 14"
47.25"BLACK IRONANGLE RING
4" & 6"
50" TO 120"
DIAMETER"L1"
JOINT SYSTEM"L1"
( 4' ) ( 8' )
47.25"
46.75"
STAINLESSANGLE RING 50" TO 120"
95.25"
94.75"
94.75"
16" TO 48"
4" & 6" 47.25"EZ CLAMP /CAST RING 95.25"
46.75"
47.25"8" TO 48" 95.25"
NA
NA
47.25"
CL
3 GORE
4 GORE
5 GORE
"D"
"R1"
STANDARD RADIUS AT THE DUCT CENTERLINE
"R1" = 1.5 X "D"
2 GORE
CL CLCL
"R2"
90° ELBOW
"R2" = "D"
STANDARD THROAT RADIUS
60° ELBOW 45° ELBOW 30° ELBOW
DUCT & FITTINGS
Gored Elbow
REV: 12/01/19 CAT024EB
OPTIONS
Duct greater than 84" diameterrequires Fab-Tech Engineeringreview and approval.
Standard gores and radii are shown,custom number of gores, custom radii,and throat extensions are available.
4" - 14"
4" - 14"
SS CAST RING
EZ CLAMP
4" - 120"
16" - 120"
BI ANGLE RING
SS ANGLE RING
OR A COMBINATION OFJOINING SYSTEMS
WITH JOINT SYSTEM
LIMITATIONS
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
24®
NOTE
All fittings with standard Fab-Techconnections include gaskets and clampsor hardware as required for installation.
DUE TO MANUFACTURING LIMITATIONS, THEFOLLOWING ELBOWS ARE NOT AVAILABLE AS
FULL RADIUS 90° ELBOW > 56" DIA. FULL RADIUS 60° ELBOW > 82" DIA. FULL RADIUS 45° ELBOW > 106" DIA.
LARGE ELBOWS ABOVE THESE LIMITS WILLBE MANUFACTURED AS SMALLER FITTINGS( AN 86" DIA. 90° ELBOW WILL BE SUPPLIED
AS TWO 45° ELBOWS FOR EXAMPLE ) OR AS
ALSO DUE TO MANUFACTURING LIMITATIONS,MANY OF THE SMALLER 1/2 RADIUS ELBOWSWILL REQUIRE CAST RINGS OR FLAT RINGS.
HALF RADIUS 90° ELBOW > 76" DIA.
ONE PIECE FITTINGS:
A CLAM SHELL DESIGNED FITTING AS TWO OR MORE PIECES. THIS APPLIES TO ALL LARGE FITTINGS AS WELL AS ELBOWS.
CONCENTRIC
"L1" = "L2" + "L4" + "L5"
ECCENTRIC
"L2""L2"
"D1"
"L4""L4" "L5""L5"
"L1""L1"
"D1" "D2""D2"
Formula to calculate the minimum length foran eccentric reducer:
Use this chart for minimum length of "L2":
6" AND LESS 12"
"D1" minus "D2" "L2"
7" TO 9" 18"
10" TO 13" 24"
14" TO 17" 30"
AMOUNT OFREDUCTION
MINIMUMLENGTH
"L1" = "L2" + "L4" + "L5"
Formula to calculate the minimum length fora concentric reducer:
Use this chart for minimum length of "L2":
9" AND LESS 12"
"D1" minus "D2" "L2"
10" TO 14" 18"
15" TO 19" 24"
20" TO 24" 30"
AMOUNT OFREDUCTION
MINIMUMLENGTH
"L3"
Use this chart for minimum length of "L4" & "L5":
4" TO 58" 3"
"D1" or "D2" "L4" or "L5"
60" TO 94" 4"
96" TO 120" 5"
DUCT DIAMETERMINIMUMLENGTH
Use this chart for minimum length of "L4 & "L5":
"D1" or "D2" "L4" or "L5"
DUCT DIAMETERMINIMUMLENGTH
4" TO 58" 3"
60" TO 94" 4"
96" TO 120" 5"
DUCT & FITTINGS
Concentric and Eccentric Reducer
REV: 12/01/19 CAT025EB
OPTIONS
Custom lengths available.
( Shorter taper or "L2" length can be fabricated,but will effect air flow. )
( Shorter taper or "L2" length can be fabricated,but will effect air flow. )
4" - 14"
4" - 14"
SS CAST RING
EZ CLAMP
4" - 120"
16" - 120"
BI ANGLE RING
SS ANGLE RING
OR A COMBINATION OFJOINING SYSTEMS
WITH JOINT SYSTEM
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
25®
NOTE
All fittings with standard Fab-Techconnections include gaskets andclamps or hardware as requiredfor installation.
"D1"
"L1"
"D2"
"L2"
DUCT & FITTINGS
Offset
REV: 12/01/19 CAT026EB
4" - 14"
4" - 14"
SS CAST RING
EZ CLAMP
4" - 120"
16" - 120"
BI ANGLE RING
SS ANGLE RING
OR A COMBINATION OFJOINING SYSTEMS
WITH JOINT SYSTEM
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
26®
NOTE
All fittings with standard Fab-Tech connectionsinclude gaskets and clamps or hardware asrequired for installation.
"D"DUCT DIA
16" - 120" BI/SSANGLE RING CONFIGURATION
WITH ADDED SUPPORT ANGLE RING
TRANSVERSE STIFFENERS REQUIREDFOR END CAPS OVER 36" DIA.
"D"DUCT DIA
FLAT CAP
HAT STYLE CAP
4" - 14"PSP-EZ™ CONFIGURATION
1/2"
( SEE OPTIONS )
DUCT & FITTINGS
End Cap
OPTIONS
Clear polycarbonate viewport endcaps available up to 12" dia.Larger sizes available with engineering review and approval.
REV: 12/01/19 CAT027EC
4" - 14"CAST RING CONFIGURATION
FLAT CAP 10 GA
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
27®
( SEE OPTIONS )
NOTE
All fittings with standard Fab-Tech connections include gasketsand clamps or hardware as required for installation.
REV: 12/01/19 CAT028EB
DUCT & FITTINGS
NOTES
All fittings with standard Fab-Tech connections include gaskets and clamps or hardware asrequired for installation.Raw end available.Round duct greater than 84" diameter requires Fab-Tech Engineering review and approval.Rectangular duct width or height of 98" and larger requires Fab-Tech Engineering review.A center stiffener (1" SCH40 pipe ) is added at the midpoint of the flange for rectangular ductwidth or height of 50" and greater.
Concentric Round to Rectangular Transition
"Y"
"DØ"
"X" "L1"
3" MIN
"R"
"L2"
FOR ECCENTRIC ROUND TORECTANGULAR FITTING, USE THECUSTOM FITTING ORDER SHEET.
4" - 14"
4" - 14"
SS CAST RING
EZ CLAMP
4" - 120"
16" - 120"
BI ANGLE RING
SS ANGLE RING
WITH ROUND JOINT SYSTEM
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
28®
DUCT & FITTINGS
Custom Fitting
REV: 12/01/19 CAT029EC
90 DEGREE REDUCING TEE 90 DEGREE WYE
ELBOW WITH HEEL TAP
USE CUSTOM FITTING ORDER SHEET TO DESCRIBE YOUR FITTING.
ECCENTRIC ROUND TO RECTANGULAR TRANSITION
4" - 14"
4" - 14"
SS CAST RING
EZ CLAMP
4" - 120"
16" - 120"
BI ANGLE RING
SS ANGLE RING
OR A COMBINATION OFJOINING SYSTEMS
WITH ROUND JOINT SYSTEM
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
29®
NOTE
All fittings with standard Fab-Tech connectionsinclude gaskets and clamps or hardware asrequired for installation.
REV: 12/01/19 CAT030ED
CONTROLDEVICES
50" & LARGERHEAVY DUTYINDUSTRIALDAMPER
PAGE: 45SIZE:50"-120"
4"-36" HORIZONTALRUN BLASTGATE
PAGE:48SIZE:4"-36"
4"-12" WAFERISOLATIONDAMPER
PAGE: 34SIZE:4"-12"
6"-14" INDUSTRIALISOLATIONDAMPER
PAGE: 38SIZE:6"-14"
CONTROLDEVICESPSP-EZ™
CONTROL DEVICES
Product Guide
6"-14" INDUSTRIALISOLATIONDAMPER
PAGE: 39SIZE:6"-14"
38" & LARGERHORIZONTAL RUNBLASTGATE
PAGE: 50SIZE:38"-120"
2" & 3" MICROADJUSTABLEEZ DAMPER
PAGE:35SIZE:2" & 3"
HORIZONTAL RUN& VERTICAL RUNEZ BLASTGATE
PAGE:47SIZE:2" & 3"
4" INDUSTRIALISOLATIONDAMPER
PAGE: 37SIZE:4"
4" INDUSTRIALISOLATIONDAMPER
PAGE: 37SIZE:4"
VERTICAL RUNBLASTGATE
PAGE: 52SIZE:4" TO 14"
HORIZONTAL RUNBLASTGATE
PAGE:48SIZE:4" TO 14"
6"-14" INDUSTRIALISOLATIONDAMPER
PAGE: 39SIZE: 6" TO 14"
6"-14" INDUSTRIALISOLATIONDAMPER
PAGE: 38SIZE:6" TO 14"
AMCA
AMCA
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
30®
38" & LARGERVERTICAL RUNACTUATEDBLASTGATE
PAGE:SIZE:38"-120"
38" & LARGERVERTICAL RUNISOLATIONBLASTGATE
PAGE:54SIZE:38"-120"
16"-36" HORIZONTALRUN ACTUATEDBLASTGATE
PAGE:49SIZE:4"-36"
38" & LARGERHORIZONTAL RUNACTUATEDBLASTGATE
PAGE: 51SIZE:38"-120"
4"-36"VERTICAL RUNISOLATIONBLASTGATE
PAGE: 52SIZE:4"-36"
16"-48" HIGH VALUEHEAVY DUTYINDUSTRIALDAMPER (HVD)
PAGE: 43SIZE:16"-34"
55
4"-14" INDUSTRIALISOLATIONSHORTDAMPER
PAGE: 40SIZE:4"-14"
16"-36" VERTICALRUN ACTUATEDBLASTGATE
PAGE: 53SIZE:16"-36"
16"-34" HIGHVALUE HEAVYDUTY INDUSTRIAL
PAGE: 42SIZE:16"-34"
AMCA
36"-48" HIGHVALUE HEAVYDUTY INDUSTRIAL
PAGE:44SIZE:36"-48"
AMCA 24"-84"ULTRA SERIESINDUSTRIALDAMPER
PAGE: 46SIZE:24"-84"
CONTROL DEVICES
Round Damper Comparison Chart
REV: 12/01/19 CAT031EC
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
31®
VIRGIN TEFLON
4"ØINDUSTRIALISOLATION DAMPER
FLUOROELASTOMER
4" - 14"ØWAFER ISOLATIONDAMPER
BODY:
BLADE:
4"Ø BLADE:EDGE SEALS:BLADE HOLDERS:
AXLE:AXLE SEALS:
BEARINGS:COATING:
QUADRANT:
PSP-EZ™ JOINING SYSTEM 4"CUSTOM HOLE PATTERNMOLDED 25% GLASS
COATED SOLID ALUMINUM BODY
COATED 10GA STAINLESS STEELWITH FULLY WELDED DRIVE AXLE
MACHINED PTFEVITON EXTRUDED RUBBER
DUAL SHAFT 1/2"Ø STAINLESS STEELLIQUID TIGHT - POS & NEG
NYLONFLUOROPOLYMER BARRIER
MANUAL LOCKING HANDLE1/2° INTERVALS
SYSTEM PRESSURE
FILLED PTFE
COATING
JOINING SYSTEM:
ACTUATOR:
BODY LENGTH:
AXLES:
BLADE & BLADE HOLERS:EDGE SEALS:
AXLE SEALS:
BODY:
FLOATING CAST STAINLESS
MANUAL LEVER
9-1/4"COATED 20GA STAINLESS STEEL
DUAL SHAFT 1/2"Ø STAINLESS STEELLIQUID TIGHT
LOCKOUT:LOCKOUT: 1/2° INTERVALSBLADE OPENS: CCW
BLADE OPENS: CW
PSP-EZ™ JOINING SYSTEM 6"-14"
CUSTOM LENGTH
CUSTOM HOLE PATTERN
ELECTRIC ACTUATOR
6" - 14"ØAMCA INDUSTRIALISOLATION DAMPER
R
AIRMOVEMENTAND CONTROLASSOCIATIONINTERNATIONAL, INC.
AIR
PERFORMANCE
LEAKAGE
AIR
CERTIFIEDRATINGS
OFFSET - 10GA COATED
MOLDED PTFEVITON
JOINING SYSTEM:
ACTUATOR:
BODY LENGTH:
AXLES:
BLADE:
BLADE HOLDERS:EDGE SEALS:
AXLE SEALS:
BODY:
FLOATING CAST STAINLESS
MANUAL LEVER
9-1/4"COATED 20GA STAINLESS STEEL
1/2° INTERVALS
DUAL SHAFT 1/2"Ø STAINLESS STEELLIQUID TIGHT
LOCKOUT:BLADE OPENS: CCW
4" - 14"ØINDUSTRIAL ISOLATIONSHORT DAMPER
4": VIRGIN TEFLON
MOLDED PTFEFLUOROELASTOMER
ACTUATOR:
BODY LENGTH:
AXLES:
BLADE OPENS:
BLADE:
BLADE HOLDERS:EDGE SEALS:
AXLE SEALS:
BODY:
MANUAL LEVER
COATED 20GA STAINLESS STEEL
1/2° INTERVALS
DUAL SHAFT 1/2"Ø STAINLESS STEELLIQUID TIGHT
LOCKOUT:CCW
4" MIN W/ EZ FLANGES
6"-14":10GA COATED STAINLESS STEEL
FLOATING BLACK IRON
COATING: PERMASHIELD FLUOROPOLYMER
CUSTOM LENGTH
ELECTRIC ACTUATORPNEUMATIC ACTUATOR
STEEL RINGS
JOINING SYSTEM: FLOATING CAST STAINLESSSTEEL RINGS
PSP-EZ™ JOINING SYSTEM 4"-14"CUSTOM HOLE PATTERN
FLOATING BLACK IRONFLAT RINGS 4"-14"
CUSTOM LENGTHBARRIER COATING
STEEL RINGS
ANGLE RINGS 6"-14"
PNEUMATIC ACTUATOR
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
BODY LENGTH: 1"
OPTION:
OPTION:OPTION:
OPTION:
OPTION:
OPTION:
OPTION:OPTION:
OPTION:
OPTION:
OPTION:
OPTION:
OPTION:OPTION:
OPTION:
OPEN/CLOSE TORQUE: 250 in-lbRECOMMENDEDMINIMUM
OPEN/CLOSE TORQUE: 250 in-lbRECOMMENDEDMINIMUM
OPEN/CLOSE TORQUE: 250 in-lbOPEN/CLOSE TORQUE: 250 in-lb
RECOMMENDEDMINIMUMRECOMMENDED
MINIMUM
FLOATING STAINLESS STEELFLAT RINGS 4"-14"
OPTION:
4-1/2" MIN W/ CAST & FLAT RINGS
6" - 14"ØINDUSTRIALISOLATION DAMPER
10GA COATED STAINLESS STEEL
MOLDED PTFEFLUOROELASTOMER
JOINING SYSTEM:
ACTUATOR:
AXLES:
BLADE OPENS:
BLADE:
BLADE HOLDERS:EDGE SEALS:
AXLE SEALS:
BODY:
MANUAL LEVER
COATED 20GA STAINLESS STEEL
1/2° INTERVALS
DUAL SHAFT 1/2"Ø STAINLESS STEELLIQUID TIGHT
LOCKOUT:CCW
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
PNEUMATIC ACTUATOR
FLOATING CAST STAINLESSSTEEL RINGS
PSP-EZ™ JOINING SYSTEM 6"-14"
CUSTOM HOLE PATTERN
FLOATING BLACK IRONANGLE RINGS 6"-14"
ELECTRIC ACTUATOR
BODY LENGTH: 9-1/4"CUSTOM LENGTH
OPTION:OPTION:
OPTION:
OPTION:OPTION:
OPTION:
OPEN/CLOSE TORQUE: 250 in-lbRECOMMENDEDMINIMUM
STAINLESS STEEL
CONTROL DEVICES
Round Damper Comparison Chart
REV: 02/18/20 CAT032ED
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
32®
16" - 34"ØAMCA HIGH VALUE HEAVY DUTYINDUSTRIAL DAMPER
OFFSET - 1/4" COATED
ACTUATOR:
BODY LENGTH:
AXLES:
LOCKOUT:
BLADE:
AXLE SEALS:
BODY:
MANUAL LEVER
10"COATED 12GA STAINLESS STEEL
1/2° INTERVALS
LIQUID TIGHTSLEEVE BEARINGS: THERMOPLASTIC
WELDEDBLADE STOPS:
MOUNTING HOLES: STRADDLE VERTICALCENTERLINE
BLADE OPENS: CCW
VITON
16" - 48"ØHIGH VALUE HEAVYDUTY INDUSTRIALDAMPER (HVD)
1/4" COATED STAINLESS STEEL
ACTUATOR:
BODY LENGTH:
AXLES:
BLADE:
AXLE SEALS:
BODY:
MANUAL LEVER
10"COATED 12GA STAINLESS STEEL
1/2° INTERVALS
LIQUID TIGHTSLEEVE BEARINGS: THERMOPLASTIC
WELDED W/ VITON BLADE SEALBLADE STOPS:
MOUNTING HOLES: STRADDLE VERTICAL
LOCKOUT:BLADE OPENS: CCW
CENTERLINE
36" - 48"ØAMCA HIGH VALUEHEAVY DUTY INDUSTRIAL DAMPER
OFFSET - 1/4" COATED
ACTUATOR:
BODY LENGTH:
AXLES:
LOCKOUT:
BLADE:
AXLE SEALS:
BODY:
MANUAL GEAR BOX W/ LOCK OUT
10"COATED 12GA STAINLESS STEEL
1/2° INTERVALS
LIQUID TIGHTSLEEVE BEARINGS: THERMOPLASTIC
WELDEDBLADE STOPS:
MOUNTING HOLES: STRADDLE VERTICAL
BLADE OPENS: CCW
CENTERLINE
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
JOINING SYSTEM:
CUSTOM HOLE PATTERN
CUSTOM ACTUATOR MOUNTING KITELECTRIC ACTUATORPNEUMATIC ACTUATOR
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
JOINING SYSTEM: STITCH WELDED COATED
CUSTOM HOLE PATTERN
CUSTOM ACTUATOR MOUNTING KITELECTRIC ACTUATORPNEUMATIC ACTUATOR
STITCH WELDED STAINLESS STEELVAN STONE RINGS
MANUAL GEAR BOX W/ LOCK OUT
JOINING SYSTEM: STITCH WELDED COATED
CUSTOM HOLE PATTERN
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
CUSTOM ACTUATOR MOUNTING KITELECTRIC ACTUATORPNEUMATIC ACTUATOR
MANUAL GEAR BOX W/ LOCK OUT
OPTION:
OPTION:
OPTION:
OPTION:
OPTION:OPTION:
DUAL SHAFT 1.38Ø STAINLESS STEELDUAL SHAFT 1.38Ø STAINLESS STEEL
OPTION:
OPTION:
OPTION:
OPTION:
OPTION:
DUAL SHAFT 1.38Ø STAINLESS STEEL
OPTION:
OPTION:OPTION:
OPTION:
OPEN/CLOSE TORQUE: 1000 in-lbOPEN/CLOSE TORQUE: 1000 in-lb
OPEN/CLOSE TORQUE: 1000 in-lb
MINIMUMMINIMUM
MINIMUMRECOMMENDED
RECOMMENDEDRECOMMENDED
STITCH WELDED COATEDBLACK IRON VAN STONE RINGSBLACK IRON VAN STONE RINGSBLACK IRON VAN STONE RINGS
VITONBLADE EDGE SEAL: BLADE EDGE SEAL:
R
AIRMOVEMENTAND CONTROLASSOCIATIONINTERNATIONAL, INC.
AIR
PERFORMANCE
LEAKAGE
AIR
CERTIFIEDRATINGS
R
AIRMOVEMENTAND CONTROLASSOCIATIONINTERNATIONAL, INC.
AIR
PERFORMANCE
LEAKAGE
AIR
CERTIFIEDRATINGS
STAINLESS STEEL STAINLESS STEEL
DIFFERENTIAL PRESSURE: 10" WGDIFFERENTIAL PRESSURE: 10" WGDIFFERENTIAL PRESSURE: 10" WG
CONTROL DEVICES
Round Damper Comparison Chart
REV: 02/18/20 CAT033EE
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
33®
24" - 84"Ø ULTRA SERIESINDUSTRIAL DAMPER
COATED REINFORCED
ACTUATOR:
BODY LENGTH:
AXLES:
LOCKOUT:
BLADE:
AXLE SEALS:
BODY:
10"
VARIABLE POSITION
24"-44" DIA. DUAL SHAFT 1.20Ø SS
LIQUID TIGHTSLEEVE BEARINGS:
SPHERICAL HEIM (60"-84")
WELDEDBLADE STOPS:
MOUNTING HOLES:STRADDLE VERTICAL
24"-58" DIA. 1/4" STAINLESS STEEL
CENTERLINE
BLADE POSITION INDICATOR:IDLE SIDE
COATED 24"-44" DIA. 10GA STAINLESS STEELCOATED 46"-84" DIA. 1/4" STAINLESS STEEL
60"-84" DIA. 3/8" STAINLESS STEEL
AVAIL TO 120" DIA W/ ENGINEERING REVIEW
JOINING SYSTEM:FULLY WELDED STAINLESSSTEEL VAN STONE RINGS
CUSTOM HOLE PATTERN
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
CUSTOM ACTUATOR MOUNTING KITELECTRIC ACTUATORPNEUMATIC ACTUATOR
OPTION:
OPTION:
OPTION:OPTION:
OPTION:
Ultra Series Industrial Dampers
Heavy Duty Industrial Dampers
AMCA High Value Heavy Duty Industrial Dampers
High Value Heavy Duty Industrial Dampers
AMCA High Value Heavy Duty Industrial Dampers
Isolation Short Industrial Dampers
AMCA Isolation Industrial Dampers
Isolation Industrial Dampers
Wafer Isolation Dampers
4 6 8 10 12 14 16 20 24 28 30 32 34 3618 22 26 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84
50"Ø & LARGERREINFORCED HEAVY DUTYINDUSTRIAL DAMPER
XL45 - UP TO 20"XL280 - 21" TO 48"XL425 - 49" TO 94"
PNEUMATIC ACTUATED DAMPERSHYTORK ACTUATOR STANDARD
3/8" COATED REINFORCED
ACTUATOR:
BODY LENGTH:
AXLES:
LOCKOUT:
BLADE:
AXLE SEALS:
BODY:
GEAR ACTUATOR W/ LOCK OUT
10"
COATED 1/4" STAINLESS STEEL
1/2° INTERVALS
LIQUID TIGHTSLEEVE BEARINGS:THERMOPLASTIC
WELDEDBLADE STOPS:
MOUNTING HOLES:STRADDLE VERTICLE
STAINLESS STEEL
CENTERLINE
BLADE OPENS: CCW
CUSTOM ACTUATOR MOUNTING KITELECTRIC ACTUATORPNEUMATIC ACTUATOROPTION:
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
AVAIL TO 120" DIA W/ ENGINEERING REVIEW
JOINING SYSTEM:FULLY WELDED STAINLESSSTEEL VAN STONE RINGS
CUSTOM HOLE PATTERN
OPTION:OPTION:
OPTION:
OPTION:
DUAL SHAFT 1.85Ø STAINLESS STEEL
NONE; STANDARD INTERFACE FORROTORK HIGH SPEED SI-1-Q SERIES
OPEN/CLOSE TORQUE:1600 in-lb RECOMMENDEDMINIMUM
46"-58" DIA. DUAL SHAFT 1.85Ø SS60" DIA. & UP DUAL SHAFT 2.45Ø SS
BLADE OPENS: CCW
Available Round Damper Sizes Chart
Available Sizes - Inches In Diameter
BRONZE SLEEVE (24"-58")
DIFFERENTIAL PRESSURE: 30" WGDIFFERENTIAL PRESSURE: 10" WG
SPECIFICATIONS
"D"
BOLTHOLESIZE
468
1012
DUCTDIA“D”
7/16
5.317.509.5011.5013.81
BOLTSIZE
BOLTCIRCLE
DIA.
NO.OF
HOLES
12
6
8
9/16
3/8
1/2
BOLT HOLE SPECIFICATIONS
CONTROL DEVICES
4"-14" Wafer Isolation Damper
REV: 12/01/19 CAT034EC
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
34®
EXTRUDEDFLUOROELASTOMERISOLATIONBLADE SEAL
C
C
1”
BODY:
BLADE:
4"Ø BLADE:EDGE SEALS:BLADE HOLDERS:
AXLE:AXLE SEALS:
BEARINGS:COATING:
QUADRANT:
MOLDED 25% GLASS
COATED SOLID ALUMINUM BODY
COATED 10GA STAINLESS STEEL
MACHINED PTFEVITON EXTRUDED RUBBER
DUAL SHAFT 1/2"Ø STAINLESS STEELLIQUID TIGHT - POS & NEG
NYLONFLUOROPOLYMER BARRIER
MANUAL LOCKING HANDLE1/2° INTERVALS
SYSTEM PRESSURE
FILLED PTFE
COATING
LOCKOUT:BLADE OPENS: CW
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
BODY LENGTH: 1"
WITH FULLY WELDED DRIVE AXLE
OPEN/CLOSE TORQUE:250 in-lb
NOTE: All fittings with standard Fab-Techconnections include gaskets and clamps orhardware as required for installation.
RECOMMENDED MIN
14 15.81
"D"
"L"
PZD02
PZD03
2"
3"
3.875"
3.875"
PART NO. "D" "L"DESCRIPTION
2" EZ-DAMPER
3" EZ-DAMPER
ACTUATORPLATE
POSITION LOCK
THUMB WHEEL
FRICTION WHEEL
CONTROL DEVICES
2" & 3" Micro-Adjustable EZ Damper
REV: 12/01/19 CAT035EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
35®
NOTE
All fittings with standard Fab-Tech connections include gaskets andclamps or hardware as required for installation.
CONTROL DEVICES
Intentionally left blank
REV: 12/01/19 CAT036EC
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
36®
CONTROL DEVICES
4" Industrial Isolation Damper
REV: 12/01/19 CAT037EB
SPECIFICATIONS
100 1000 10000Velocity (f/m)
0.001
0.01
0.1
1.0
Pre
ssu
re D
rop
(in
. w
g)
Virgin Teflon bladewith fluoroelastomeredge seal
Pressure Drop Test based on AMCA Standard 500-D-98, Ref. Fig 5.3
Damper Leakage Test based on ANSI/AMCA Standard 500-D-07, Ref. Fig 5.6
0.35
0.3
0.25
0.2
0.15
0.1
0.05
00 5 10 15
Leakag
e (
CF
M)
Pressure (in. wg)
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
37®
"D"
9.25" STD
3"
VIRGIN TEFLONFLUOROELASTOMER
PSP-EZ™ JOINING SYSTEM 4"CUSTOM HOLE PATTERN
JOINING SYSTEM:
ACTUATOR:
BODY LENGTH:
AXLES:
BLADE & BLADE HOLERS:EDGE SEALS:
AXLE SEALS:
BODY:
FLOATING CAST STAINLESS
MANUAL LEVER
9-1/4"
COATED 20GA STAINLESS STEEL
DUAL SHAFT 1/2"Ø STAINLESS STEELLIQUID TIGHT
LOCKOUT: 1/2° INTERVALSBLADE OPENS: CCW
CUSTOM LENGTH
ELECTRIC ACTUATORPNEUMATIC ACTUATOR
STEEL RINGS
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
OPTION:OPTION:
OPTION:OPTION:
OPTION:
NOTE: All fittings with standard Fab-Techconnections include gaskets and clamps orhardware as required for installation.
OPEN/CLOSE TORQUE:250 in-lb RECOMMENDED MIN
CONTROL DEVICES
6"-14" Industrial Isolation Damper
REV: 12/01/19 CAT038EB
SPECIFICATIONS
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
38®
9.25" STD
3"
"D"
VITONEDGESEAL
10GA COATED STAINLESS STEEL
MOLDED PTFEFLUOROELASTOMER
JOINING SYSTEM:
ACTUATOR:
AXLES:
BLADE OPENS:
BLADE:
BLADE HOLDERS:EDGE SEALS:
AXLE SEALS:
BODY:
MANUAL LEVER
COATED 20GA STAINLESS STEEL
1/2° INTERVALS
DUAL SHAFT 1/2"Ø STAINLESS STEELLIQUID TIGHT
LOCKOUT:CCW
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
PNEUMATIC ACTUATOR
FLOATING CAST STAINLESSSTEEL RINGS
PSP-EZ™ JOINING SYSTEM 6"-14"
CUSTOM HOLE PATTERN
FLOATING BLACK IRONANGLE RINGS 6"-14"
ELECTRIC ACTUATOR
BODY LENGTH: 9-1/4"CUSTOM LENGTH
OPTION:OPTION:
OPTION:
OPTION:OPTION:
OPTION:
NOTE: All fittings with standard Fab-Techconnections include gaskets and clamps orhardware as required for installation.
OPEN/CLOSE TORQUE:250 in-lb RECOMMENDED MIN
CONTROL DEVICES
6"-14" AMCA Industrial Isolation Damper
REV: 12/01/19 CAT039EC
SPECIFICATIONS
100 1000 10000Velocity (f/m)
0.001
0.01
0.1
1.0
Pre
ssu
re D
rop
(in
. w
g)
Fab-Tech, Inc. certifies that the Industrial Single BladeIsolation Damper shown herein is licensed to bear theAMCA Seal. The ratings shown are based on testsand procedures performed in accordance with AMCAPublication 511 and comply with the requirements ofthe AMCA Certified Ratings Program.
The AMCA Certified Ratings Seal applies to AirLeakage ratings and Air Performance ratings.
CERTIFIEDRATINGS
AIR
PERFORMANCE
LEAKAGE
AIR
R
AIRMOVEMENTAND CONTROLASSOCIATIONINTERNATIONAL, INC.
1A 15.2 (3)*
PressureClass
N/A N/A
1
2
3
20.3 (4)
50.8 (10)
203 (40)
40.6 (8)
102 (20)
406 (80)
55.9 (11)
142 (28)
569 (112)
71.1 (14)
178 (35)
711 (140)
N/A
0.25 kPa(1” wg) (4” wg) (8” wg) (12” wg)
1.0 kPa 2.0 kPa 3.0 kPa
2 3 2L/s/m (ft /min/ft )
1. Test method per AMCA Standard 500-892Data based on a seating torque of: 764 in-lbf/ft
2for 6" damper, 234 in-lbf/ft for 14" damper
2. Air leakage is based on operation between50°F & 104°F (10°C to 40°C) and data corrected
3to represent standard air density 0.075 lbs/ft .
6
10
14
RequiredRange
ExtendedRange (Optional)
*Units for maximum ratings in ( ) are CFM Sq. Ft.
Leakage Classification
Damper Dia.
6" - 14"1"WG 1A
Pressure Drop Test based on AMCA Standard 500-D-98, Ref. Fig 5.3
Damper Leakage Test based on ANSI/AMCA Standard 500-D-07, Ref. Fig 5.6
Tested Leakage Rates Available, Contact Fab-Tech Inc.
Pressure AMCA Leakage Class
14",8",12"WG
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
39®
PSP-EZ™ JOINING SYSTEM 6"-14"
CUSTOM LENGTH
CUSTOM HOLE PATTERN
ELECTRIC ACTUATOR
OFFSET - 10GA COATED
MOLDED PTFE
VITON
JOINING SYSTEM:
ACTUATOR:
BODY LENGTH:
AXLES:
BLADE:
BLADE HOLDERS:
EDGE SEALS:
AXLE SEALS:
BODY:
FLOATING CAST STAINLESS
MANUAL LEVER
9-1/4"
COATED 20GA STAINLESS STEEL
1/2° INTERVALS
DUAL SHAFT 1/2"Ø STAINLESS STEEL
LIQUID TIGHT
LOCKOUT:
BLADE OPENS:CCW
FLOATING BLACK IRON
COATING: PERMASHIELD FLUOROPOLYMER
BARRIER COATING
STEEL RINGS
ANGLE RINGS 6"-14"
PNEUMATIC ACTUATOR
OPTION:
OPTION:
OPTION:
OPTION:
OPTION:
OPTION:
NOTE: All fittings with standard Fab-Techconnections include gaskets and clamps orhardware as required for installation.
OPEN/CLOSE TORQUE: 250 in-lb
RECOMMENDED MINIMUM
STAINLESS STEEL
9.25" STD
3"EXTRUDEDFLUOROELASTOMERRUBBER EDGE SEAL
D1
OFFSETBLADE
CONTROL DEVICES
REV: 12/01/19 CAT040EC
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
40®
4"-14" Industrial Isolation Short Damper
SPECIFICATIONS
"D"
4" PTFE
DIAMETER BLADE
20GA
BODY
6" TO 14" 10GA 20GA
4" PTFE bladewith molded PTFE
blade holders
4": VIRGIN TEFLON
MOLDED PTFEFLUOROELASTOMER
ACTUATOR:
BODY LENGTH:
AXLES:
BLADE OPENS:
BLADE:
BLADE HOLDERS:EDGE SEAL:
AXLE SEALS:
BODY:
MANUAL LEVER
COATED 20GA STAINLESS STEEL
1/2° INTERVALS
DUAL SHAFT 1/2"Ø STAINLESS STEELLIQUID TIGHT
LOCKOUT:CCW
4" MINIMUM WITH EZ FLANGES
6"-14":10GA COATED STAINLESS STEEL
JOINING SYSTEM:FLOATING CAST STAINLESSSTEEL RINGS
PSP-EZ™ JOINING SYSTEM 4"-14"CUSTOM HOLE PATTERN
FLOATING BLACK IRONFLAT RINGS 4"-14"
CUSTOM LENGTHCOATING: PERMASHIELD FLUOROPOLYMER
BARRIER COATING
OPTION:
OPTION:
OPTION:
OPTION:
NOTE: All fittings with standard Fab-Techconnections include gaskets and clamps orhardware as required for installation.
OPEN/CLOSE TORQUE: 250 in-lb RECOMMENDED MIN
FLOATING STAINLESS STEELFLAT RINGS 4"-14"
OPTION:
4-1/2" MIN WITH CAST OR FLAT RINGS
4" MIN WITH EZ FLANGES4-1/2" MIN WITH CAST OR FLAT RINGS
CONTROL DEVICES
6”-14" Industrial Isolation Damper
REV: 12/01/19 CAT041EB
From SupplySystem andAirflowMeasuringSection
PL-X
PL-Y PL-Z
PL-9
PL-1 PL-4
PL-2
10D min.6D min.
DeviceUnderTest
Inlet Cone Requiredif Attached to Plenum
PS9 PS4
D ± 0.02DD ± 0.02D
td9
D = duct diameter for round ducts
Fig. 5.3: Test Damper Setup with Inlet and Outlet Ducts
PS9
DeviceUnderTest
Flowmeter
AIRFLOW
PressurizedSupply Air
Blank off plate.Seal airtight todamper flange.
Fig. 5.6: Test Damper Setup - Leakage Test with Damper underPositive Pressure
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
41®
REV: 02/18/20 CAT042ED
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
10" STD
"D"5" STD
SPECIFICATIONS
19.26"
100 1000 10000Velocity (f/m)
0.001
0.01
0.1
1.0
Pre
ssu
re D
rop
(in
. w
g)
Fab-Tech, Inc. certifies that the Industrial Single BladeIsolation Damper shown herein is licensed to bear theAMCA Seal. The ratings shown are based on testsand procedures performed in accordance with AMCAPublication 511 and comply with the requirements ofthe AMCA Certified Ratings Program.
The AMCA Certified Ratings Seal applies to AirLeakage ratings and Air Performance ratings.
CERTIFIEDRATINGS
AIR
PERFORMANCE
LEAKAGE
AIR
R
AIRMOVEMENTAND CONTROLASSOCIATIONINTERNATIONAL, INC.
1A 15.2 (3)*
PressureClass
N/A N/A
1
2
3
20.3 (4)
50.8 (10)
203 (40)
40.6 (8)
102 (20)
406 (80)
55.9 (11)
142 (28)
569 (112)
71.1 (14)
178 (35)
711 (140)
N/A
0.25 kPa(1” wg) (4” wg) (8” wg) (12” wg)
1.0 kPa 2.0 kPa 3.0 kPa
2 3 2L/s/m (ft /min/ft )
1. Test method per AMCA Standard 500-892Data based on a seating torque of: 125 in-lbf/ft
2for 16" damper, 86 in-lbf/ft for 48" damper
2. Air leakage is based on operation between50°F & 104°F (10°C to 40°C) and data corrected
3to represent standard air density 0.075 lbs/ft .
RequiredRange
ExtendedRange (Optional)
*Units for maximum ratings in ( ) are CFM Sq. Ft.
Leakage Classification
Damper Dia.
16" - 34"1"WG 1A
Pressure Drop Test based on AMCA Standard 500-D-98, Ref. Fig 5.3
Damper Leakage Test based on ANSI/AMCA Standard 500-D-07, Ref. Fig 5.6
Tested Leakage Rates Available, Contact Fab-Tech Inc.
Pressure AMCA Leakage Class
14",8",12"WG
16
36
24
STAINLESS STEELQUADRANTHANDLE SHOWN
HANDLELOCKINGNUT
16"-34" AMCA High Value Heavy Duty Industrial Damper
CONTROL DEVICES 42®
OFFSET - 1/4" COATED STAINLESS STEEL
ACTUATOR:
BODY LENGTH:
AXLES:
LOCKOUT:
BLADE:
AXLE SEALS:
BODY:
MANUAL LEVER
10"COATED 12GA STAINLESS STEEL
1/2° INTERVALS
LIQUID TIGHTSLEEVE BEARINGS:THERMOPLASTIC
WELDEDBLADE STOPS:
MOUNTING HOLES: STRADDLE VERTICALCENTERLINE
BLADE OPENS: CCW
VITON
JOINING SYSTEM: STITCH WELDED COATED BLACKIRON VAN STONE RINGS
CUSTOM HOLE PATTERN
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
CUSTOM ACTUATOR MOUNTING KITELECTRIC ACTUATORPNEUMATIC ACTUATOR
MANUAL GEAR BOX W/ LOCK OUT
OPTION:
DUAL SHAFT 1.38Ø STAINLESS STEEL
OPTION:
OPTION:OPTION:
OPTION:
NOTE: All fittings with standard Fab-Techconnections include gaskets and clamps orhardware as required for installation.
OPEN/CLOSE TORQUE: 1000 in-lb RECOMMENDED MIN
BLADE EDGE SEAL:
OFFSETBLADE
DIFFERENTIAL PRESSURE: 10" WG
REV: 02/18/20 CAT043ED
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
10" STD
"D"
STAINLESS STEELQUADRANTHANDLE SHOWN
5" STD
16"-48" High Value Heavy Duty Industrial Damper (HVD)
SPECIFICATIONS
19-1/4"
HANDLELOCKINGNUT
*SHOWN WITH MANUAL HANDLE ACTUATOR OPTION
CONTROL DEVICES43®
1/4" COATED STAINLESS STEEL
ACTUATOR:
BODY LENGTH:
AXLES:
BLADE:
AXLE SEALS:
BODY:
MANUAL LEVER
10"COATED 12GA STAINLESS STEEL
1/2° INTERVALS
LIQUID TIGHTSLEEVE BEARINGS: THERMOPLASTIC
WELDED W/ VITON BLADE SEALBLADE STOPS:
MOUNTING HOLES: STRADDLE VERTICAL
LOCKOUT:BLADE OPENS: CCW
CENTERLINE
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
JOINING SYSTEM: STITCH WELDED COATED BLACKIRON VAN STONE RINGS
CUSTOM HOLE PATTERN
CUSTOM ACTUATOR MOUNTING KITELECTRIC ACTUATORPNEUMATIC ACTUATOR
STITCH WELDED STAINLESS STEELVAN STONE RINGS
MANUAL GEAR BOX W/ LOCK OUT
OPTION:
DUAL SHAFT 1.38Ø STAINLESS STEEL
OPTION:
OPTION:
OPTION:
OPTION:
OPTION:
OPEN/CLOSE TORQUE: 1000 in-lb RECOMMENDED MIN
NOTE: All fittings with standard Fab-Techconnections include gaskets and clamps orhardware as required for installation.
DIFFERENTIAL PRESSURE: 10" WG
CONTROL DEVICES
REV: 02/18/20 CAT044ED
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
44
10" STD
LOCKOUT
5" STD
36"-48" AMCA High Value Heavy Duty Industrial Damper
SPECIFICATIONS
"D"
100 1000 10000Velocity (f/m)
0.001
0.01
0.1
1.0
Pre
ssu
re D
rop
(in
. w
g)
Fab-Tech, Inc. certifies that the Industrial Single BladeIsolation Damper shown herein is licensed to bear theAMCA Seal. The ratings shown are based on testsand procedures performed in accordance with AMCAPublication 511 and comply with the requirements ofthe AMCA Certified Ratings Program.
The AMCA Certified Ratings Seal applies to AirLeakage ratings and Air Performance ratings.
CERTIFIEDRATINGS
AIR
PERFORMANCE
LEAKAGE
AIR
R
AIRMOVEMENTAND CONTROLASSOCIATIONINTERNATIONAL, INC.
1A 15.2 (3)*
PressureClass
N/A N/A
1
2
3
20.3 (4)
50.8 (10)
203 (40)
40.6 (8)
102 (20)
406 (80)
55.9 (11)
142 (28)
569 (112)
71.1 (14)
178 (35)
711 (140)
N/A
0.25 kPa(1” wg) (4” wg) (8” wg) (12” wg)
1.0 kPa 2.0 kPa 3.0 kPa
2 3 2L/s/m (ft /min/ft )
1. Test method per AMCA Standard 500-892Data based on a seating torque of: 125 in-lbf/ft
2for 16" damper, 86 in-lbf/ft for 48" damper
2. Air leakage is based on operation between50°F & 104°F (10°C to 40°C) and data corrected
3to represent standard air density 0.075 lbs/ft .
RequiredRange
ExtendedRange (Optional)
*Units for maximum ratings in ( ) are CFM Sq. Ft.
Leakage Classification
Damper Dia.
36" - 48"1"WG 1A
Pressure Drop Test based on AMCA Standard 500-D-98, Ref. Fig 5.3
Damper Leakage Test based on ANSI/AMCA Standard 500-D-07, Ref. Fig 5.6
Tested Leakage Rates Available, Contact Fab-Tech Inc.
Pressure AMCA Leakage Class
14",8",12"WG
16
36
24
®
OFFSET - 1/4" COATED STAINLESS STEEL
ACTUATOR:
BODY LENGTH:
AXLES:
LOCKOUT:
BLADE:
AXLE SEALS:
BODY:
MANUAL GEAR BOX W/ LOCK OUT
10"
COATED 12GA STAINLESS STEEL
1/2° INTERVALS
LIQUID TIGHT
SLEEVE BEARINGS:THERMOPLASTIC
WELDEDBLADE STOPS:
MOUNTING HOLES: STRADDLE VERTICAL
BLADE OPENS: CCW
CENTERLINE
COATING: PERMASHIELD FLUOROPOLYMER
BARRIER COATING
JOINING SYSTEM: STITCH WELDED COATED
BLACK IRON VAN STONE RINGS
CUSTOM HOLE PATTERN
CUSTOM ACTUATOR MOUNTING KIT
ELECTRIC ACTUATOR
PNEUMATIC ACTUATOR
OPTION:
OPTION:
OPTION:
OPTION:
DUAL SHAFT 1.38Ø STAINLESS STEEL
NOTE: All fittings with standard Fab-Techconnections include gaskets and clamps orhardware as required for installation.
OPEN/CLOSE TORQUE: 1000 in-lb RECOMMENDED MIN
VITONBLADE EDGE SEAL:
OFFSETBLADE
DIFFERENTIAL PRESSURE: 10" WG
CONTROL DEVICES
REV: 02/18/20 CAT045EC
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
45®
10"STD
"D"
BLADE STOP
5"STD
50" & Larger Reinforced Heavy Duty Industrial Damper
SPECIFICATIONS
XL45 - UP TO 20"XL280 - 21" TO 48"XL425 - 49" TO 94"
PNEUMATIC ACTUATED DAMPERSHYTORK ACTUATOR STANDARD
3/8" COATED REINFORCED
ACTUATOR:
BODY LENGTH:
AXLES:
LOCKOUT:
BLADE:
AXLE SEALS:
BODY:
GEAR ACTUATOR W/ LOCK OUT
10"
COATED 1/4" STAINLESS STEEL
1/2° INTERVALS
LIQUID TIGHTSLEEVE BEARINGS:THERMOPLASTIC
WELDEDBLADE STOPS:
MOUNTING HOLES:STRADDLE VERTICLE
STAINLESS STEEL
CENTERLINE
BLADE OPENS: CCW
CUSTOM ACTUATOR MOUNTING KITELECTRIC ACTUATORPNEUMATIC ACTUATOROPTION:
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
AVAIL TO 120" DIA W/ ENGINEERING REVIEW
JOINING SYSTEM:FULLY WELDED STAINLESSSTEEL VAN STONE RINGS
CUSTOM HOLE PATTERN
OPTION:OPTION:
OPTION:
OPTION:
DUAL SHAFT 1.85Ø STAINLESS STEEL
NOTE: All fittings with standard Fab-Techconnections include gaskets and clamps orhardware as required for installation.
OPEN/CLOSE TORQUE:1600 in-lb RECOMMENDED MIN
DIFFERENTIAL PRESSURE: 10" WG
REV: 02/18/20 CAT046ED
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
24" - 84" Ultra Series Industrial Damper
SPECIFICATIONS
NOTE: All fittings with standard Fab-Techconnections include gaskets and clamps orhardware as required for installation.
10"STD
5"STD
BLADE STOP
"D"
CONTROL DEVICES 46®
COATED REINFORCED
ACTUATOR:
BODY LENGTH:
AXLES:
LOCKOUT:
BLADE:
AXLE SEALS:
BODY:
10"
VARIABLE POSITION
24"-44" DIA. DUAL SHAFT 1.20Ø STAINLESS STEEL
LIQUID TIGHTSLEEVE BEARINGS:
SPHERICAL HEIM (60"-84")
WELDEDBLADE STOPS:
MOUNTING HOLES:STRADDLE VERTICAL
24"-58" DIA. 1/4" STAINLESS STEEL
CENTERLINE
BLADE OPENS: CCW
COATED 24"-44" DIA. 10GA STAINLESS STEELCOATED 46"-84" DIA. 1/4" STAINLESS STEEL
60"-84" DIA. 3/8" STAINLESS STEEL
AVAIL TO 120" DIA W/ ENGINEERING REVIEW
JOINING SYSTEM:FULLY WELDED STAINLESSSTEEL VAN STONE RINGS
CUSTOM HOLE PATTERN
COATING: PERMASHIELD FLUOROPOLYMERBARRIER COATING
CUSTOM ACTUATOR MOUNTING KITELECTRIC ACTUATORPNEUMATIC ACTUATOR
OPTION:
OPTION:
OPTION:OPTION:
OPTION:
NONE; STANDARD INTERFACE FORROTORK HIGH SPEED SI-1-Q SERIES
46"-58" DIA. DUAL SHAFT 1.85Ø STAINLESS STEEL60" DIA. & UP DUAL SHAFT 2.45Ø STAINLESS STEEL
BLADE POSITION INDICATOR:IDLE SIDE
IDLE SIDEBLADE POSITION
INDICATORDRIVESIDE
BRONZE SLEEVE (24"-58")
DIFFERENTIAL PRESSURE: 30" WG
CONTROL DEVICES
REV: 12/01/19 CAT047EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
47®
8.5"
PZB02H 2" 8.000”
PART NO.* "D" "L"DESCRIPTION
2" EZ-BLASTGATE HORIZONTAL
2" & 3" EZ Blastgate
"D"
SPECIFICATIONS
Stainless steel frame material.
Blade lockout system.
"L"
8.5"
PZB03H 3" 8.000”3" EZ-BLASTGATE HORIZONTAL
"D"
"L"
PZB02V 2" 8.000”
8.000”
PART NO.* "D" "L"DESCRIPTION
2" EZ-BLASTGATE VERTICAL
PZB03V 3"3" EZ-BLASTGATE VERTICAL
8.5"
NOTE
All fittings with standard Fab-Tech connectionsinclude gaskets and clamps or hardware asrequired for installation.
CONTROL DEVICES
REV: 12/01/19 CAT048EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
48
1
1
.31"
.31"
NO. OFBLADES
4" TO 16"
18" TO 36"
DIA. "D" + 4"
DIA. "D" + 4.5"
18GA
16GA
BODYBODYBOLTS
DUCT DIA."D"
OUTSIDE DIM"L1"
"L1"
"D"
ANGLERING
8"STD
( SEE CHART )
STAINLESSSTEEL BLADE
PTFE WIPER( TYP BOTH SIDES OF BLADE )
BLADELOCKOUT(STD)
UPPERBODY
LOWERBODY
4"-36" Horizontal Run Isolation Blastgate
SPECIFICATIONS
Stainless steel frame material.
Blade lockout system.
18GA
16GA
BLADE
4" - 14"
4" - 14"
SS CAST RING
EZ CLAMP
4" - 36"
16" - 36"
BI ANGLE RING
SS ANGLE RING
WITH JOINT SYSTEM
NOTE
All fittings with standard Fab-Techconnections include gaskets andclamps or hardware as required forinstallation.
®
1.38"
NO. OFBLADES
16" TO 36" 2 x "D" + 30" 10GA
BODYBODYBOLTS
DUCT DIA."D"
OUTSIDE DIM"L1"
CONTROL DEVICES
16"-36" Horizontal Run Actuated Isolation Blastgate
REV: 12/01/19 CAT049EB
SPECIFICATIONS
Stainless steel frame material.
Blade lockout system.
12GA
BLADE
16" - 36"
16" - 36"
BI ANGLE RING
SS ANGLE RING
RING TYPES
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
49®
NOTE
All fittings with standard Fab-Techconnections include gaskets andclamps or hardware as required forinstallation.
2 x "D" + 30""L1"
D1 D2
"D"
18""L2""D" + 12.5"
CHAINWHEELACTUATOR
Exterior position indicator.
SINGLEBLADE
OPTIONS
Bellows enclosed lead screw foradditional corrosion resistance( adds to L1 length )
CONTROL DEVICES
REV: 12/01/19 CAT050EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
50®
2
3
.31"
.38"
.50"
NO. OFBLADES
38" TO 46"
48" TO 60"
*86" TO 96"
DIA. "D" + 10"
DIA. "D" + 11"
DIA. "D" + 11"
14GA
12GA
10GA
10GA
10GA
10GA
BODY BLADEBODYBOLTS
DUCT DIA."D"
OUTSIDE DIM"L1"
4.63"*98" and UP DIA. "D" + 11" 10GA3/16
14GA
14GA
12GA
COLLAR
10GA
.38"62" TO 84" DIA. "D" + 11" 12GA10GA 14GA 3
2
SPECIFICATIONS
Stainless steel body, rings and blade.
Blade lockout system.38" - 120"
16" - 120"
BI ANGLE RING
SS ANGLE RING
WITH JOINT SYSTEM
NOTE
All fittings with standard Fab-Tech connections include gaskets andclamps or hardware as required for installation.
* Blastgates 86" diameter and larger subject to engineering review and approval.
BLADE
8"STD
"L1"( SEE CHART )
"D"
UPPER BODY COLLAR
LOWER BODY COLLAR
SPACER
ANGLERING
BLADELOCKOUT(STD)
BLADE
PTFE WIPER( TYP BOTH SIDES OF BLADE)
Blastgates 86" diameter and larger subject to engineering review and approval.
38" & Larger Horizontal Run Isolation Blastgate
CONTROL DEVICES
1REV: 12/01/19 CAT051EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
51®
1.38"
NO. OFBLADES
38" TO 64" 2 x "D" + 30" 12GA10GA
BODY BLADEBODYBOLTS
DUCT DIA."D"
OUTSIDE DIM"L1"
.43"66" TO 88" 2 x "D" + 30" 12GA10GA 1
38" & Larger Horizontal Run Actuated Isolation Blastgate
SPECIFICATIONS
Stainless steel body, rings and blade.
Blade lockout system.
38" - 120"
38" - 120"
BI ANGLE RING
SS ANGLE RING
RING TYPES
NOTE
All fittings with standard Fab-Tech connections include gaskets andclamps or hardware as required for installation.
* Blastgates 90" diameter and larger subject to engineering review and approval.
Blastgates 90" diameter and larger subject to engineering review and approval.
2 x "D" + 30""L1"
D1 D2
"D"
18""L2""D" + 12.5"
CHAINWHEELACTUATOR
Exterior position indicator.
OPTIONS
Bellows enclosed lead screw for additionalcorrosion resistance ( adds to L1 length )
CONTROL DEVICES
4"-36" Vertical Run Isolation Blastgate
REV: 12/01/19 CAT052EC
SPECIFICATIONSStainless steel body, rings and blade.
Blade lockout system.
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
NOTE
52
All fittings with standard Fab-Tech connections include gasketsand clamps or hardware as required for installation.
®
1
1
1
.31"
.31"
.31"
NO. OFBLADES
4" TO 8"
10" TO 16"
18" TO 36"
DIA. "D" + 4"
DIA. "D" + 4"
DIA. "D" + 4.5"
18GA
18GA
16GA
18GA
18GA
16GA
BODY BLADEFRAMEBOLTS
DUCT DIA."D"
OUTSIDE DIM"L1"
15°
15°
15°
BLADEANGLE
8"
12"
16"
LENGTH"L2"
"L1"
"D"
ANGLERING
( SEE CHART )
STAINLESSSTEEL BLADE
PTFE WIPER( TYP BOTH SIDES OF BLADE )
BLADELOCKOUT(STD)
UPPERBODY
LOWERBODY
"L2"( SEE CHART )15°
4" - 14"
4" - 14"
SS CAST RING
EZ CLAMP
4" - 48"
16" - 120"
BI ANGLE RING
SS ANGLE RING
WITH JOINT SYSTEM
REV: 12/01/19 CAT053EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
53®
1.38"
NO. OFBLADES
16" TO 36" 2 x "D" + 30" 12GA10GA
BODY BLADEFRAMEBOLTS
DUCT DIA."D"
OUTSIDE DIM"L1"
10°
BLADEANGLE
CONTROL DEVICES
16"-36" Vertical Run Actuated Isolation Blastgate
SPECIFICATIONS
Stainless steel frame material.
Blade lockout system.
16" - 36"
16" - 36"
BI ANGLE RING
SS ANGLE RING
RING TYPES
NOTE
All fittings with standard Fab-Tech connections include gasketsand clamps or hardware as required for installation.
Exterior position indicator.
"D"
CHAINWHEELACTUATOR
24"
"L3""D" + 12.5"
"D1"
"D2"
"L1"2 x "D" + 30"
OPTIONS
Bellows enclosed lead screw for additionalcorrosion resistance ( adds to L1 length )
REV: 12/01/19 CAT054EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
54
2
2
3
.31"
.38"
.38"
NO. OFBLADES
38" TO 46"
48" TO 60"
62" TO 84"
DIA. "D" + 10"
DIA. "D" + 11"
DIA. "D" + 11"
14GA
12GA
12GA
10GA
10GA
10GA
14GA
14GA
14GA
BODY BLADE COLLARBODYBOLTS
DUCT DIA."D"
OUTSIDE DIM"L1"
10°
10°
10°
BLADEANGLE
16"
24"
24"
LENGTH"L2"
ANGLERING
LOWER BODY
BLADE
COLLAR
PTFE WIPER( TYP BOTH SIDES OF BLADE)
CONTROL DEVICES
38" & Larger Vertical Run Isolation Blastgate
SPECIFICATIONSStainless steel body, rings and blade.
Vertical run blastgates greater than 84" require engineeringreview and approval.
Blade lockout system.
38" - 120"
38" - 120"
BI ANGLE RING
SS ANGLE RING
WITH JOINT SYSTEM
NOTE
All fittings with standard Fab-Tech connections include gasketsand clamps or hardware as required for installation.
* Blastgates 86" diameter and larger are subject to engineering review and approval.
BLADELOCKOUT(STD)
"D"
"L1"( SEE CHART )
BLADE
BLADE
"L2"( SEE CHART )
UPPERBODY
SPACER
COLLAR
10°
Blastgates 86" diameter and larger are subject to engineeringreview and approval.
®
1
1
.38"
.43"
NO. OFBLADES
38" TO 64"
66" TO 88"
2 x "D" + 30"
2 x "D" + 30"
12GA
12GA
10GA
10GA
12GA
12GA
BODY BLADE COLLARBODYBOLTS
DUCT DIA."D"
OUTSIDE DIM"L1"
10°
10°
BLADEANGLE
CONTROL DEVICES
38" & Larger Vertical Run Actuated Isolation Blastgate
REV: 12/01/19 CAT055EB
SPECIFICATIONSStainless steel body, rings and blade.
Exterior position indicator.
Blade lockout system.
38" - 120"
38" - 120"
BI ANGLE RING
SS ANGLE RING
RING TYPES
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
NOTE
55®
All fittings with standard Fab-Tech connections include gasketsand clamps or hardware as required for installation.
* Blastgates 90" diameter and larger are subject to engineering review and approval.
Blastgates 90" diameter and larger are subject to engineeringreview and approval.
"D"
CHAINWHEELACTUATOR
24"
"L3""D" + 12.5"
"D1"
"D2"
"L1"2 x "D" + 30"
OPTIONS
Bellows enclosed lead screw for additionalcorrosion resistance ( adds to L1 length )
ACCESSORIES
REV: 12/01/19 CAT056EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
56
FIELD INSTALLEDNIPPLE
PAGE: 57SIZE:
FIELD INSTALLEDTEST PORT
PAGE: 58SIZE: 3/8", 3/4", 2"
FIELD INSTALLEDSADDLE TAP
PAGE: 59SIZE:4"-24" TEE
1", 1-1/2", 2"
FIELD INSTALLEDHOT TAP
PAGE: 60SIZE: 4"-24"
FIELD INSTALLEDSADDLE TAP
PAGE:59SIZE:4" TO 14" TEE
CLAMP KIT
4" TO 14"SIZE:
63PAGE:
CLAMP KIT
2" & 3"SIZE:
63PAGE:
CLAMP
2" & 3"SIZE:
63PAGE:
DIE CUT GASKET
2" & 3"SIZE:
63PAGE:
ACCESSORIES
ACCESSORIESPSP-EZ™
Product Guide
®
ANGLE RINGSTAINLESS STEELOR BLACK IRON
PAGE: 62SIZE: 4"-120"
CAST RINGSTAINLESS STEEL
PAGE: 61SIZE: 4"-14"
ACCESSORIES
REV: 12/01/19 CAT057EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
57®
STRAIGHTPIPE THREAD
TAPERPIPE THREAD
DIE-CUT GASKET
*SWAGE KIT REQUIRED TO INSTALL
NIPPLE
PTFE DIE-CUT GASKET
DUCT
JAMNUT
PRT01
PRT15
6" DIA. DUCT MIN.
8" DIA. DUCT MIN.16 GA MAXMATERIAL
THICKNESS
PART NO. MIN. HOST DUCT MATERIAL THICKNESSDESCRIPTION
1" NPT NIPPLE
1-1/2" NPT NIPPLE
PRT02 10" DIA. DUCT MIN.2" NPT NIPPLE
TPS01
TPS02
PART NO.* DESCRIPTION
MANUAL KIT FOR 1"
HYDRAULIC KIT FOR 1", 1-1/2", & 2"
1-1/2"
ONLY ONE KIT REQUIRED TO INSTALL MULTIPLE NIPPLES
Field Installed Nipple
NOTES
Refer to Fab-Tech's INSTALLATION ANDASSEMBLY GUIDE for assembly instructions.
ACCESSORIES
REV: 12/01/19 CAT058EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
58
FTFI38TP
FTFI34TP
2" DIA. DUCT MIN.
6" DIA. DUCT MIN.
PART NO. MIN. HOST DUCT THRU HOLEDESCRIPTION
3/8" TEST PORT
3/4" TEST PORT
1/4" DIA.
1/2" DIA.
REDRILL
1/16" NPT
1/4" NPT
3/8" MAX
3/4" MAX
I.D. TAP HOLE
Field Installed Test Port
NOTES
Refer to Fab-Tech's INSTALLATION ANDASSEMBLY GUIDE for assembly instructions.
The unique handle design of this test port allows it tobe installed quickly and easily in-the-field with commontools and without system shutdown or disassembly.
SPECIFICATIONS®Nipple made of pure PVDF, seal made of Viton
Stainless steel hex nut
Able to re-drill through hole to slightly larger hole ordrill and tap test port for female threads - thread O.D.cannot exceed max re-drill diameter
Installs in duct as small as 2" diameter - providesliquid tight seal - does not compromise the integrityof the duct interior coating
®
FTFI20TP 12" DIA. DUCT MIN.2" TEST PORT 9/16" DIA. 3/8" NPT1-3/4" MAX
.75"
APPROX.1-3/4"
DUCT
HEX NUT
SEAL
TO COMPLETE THE INSTALLATION,SIMPLY REMOVE THE STEM TO EXPOSETHE PORT AND ATTACH FITTING OR LINE.
SEAL
HEX NUT
HANDLE(REMOVABLE)
3/8" TEST PORT
TESTPORT
FTFI20TPFTFI34TP
FTFI38TP
NPT
ACCESSORIES
REV: 12/01/19 CAT059EC
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
59®
D1
STUDS AND NUTS
EXTERIORSADDLE
PTFE GASKET
SECTION THROUGH DUCT - STRAIGHT TAP
6"STD
D1 6"STD
SECTION THROUGH DUCT - LATERAL TAP
Field Installed Saddle Tap
NOTES
Refer to Fab-Tech's INSTALLATION AND ASSEMBLY GUIDEfor assembly instructions.
®Fab-Tech's PSP saddle tap will allow a new branch to beinstalled without shutting down the exhaust system.
Straight tap standard - other tap styles available with engineeringreview and approval.
HOST DUCT I.D., WALLTHICKNESS & MATERIAL TYPE
( REQUIRED INFORMATION )
WITH JOINT SYSTEM
All fittings with standard Fab-Tech connections include gasketsand clamps or hardware as required for installation.
45°
D1
9"STD
HOST DUCTD2
FLUOROPOLYMER COATEDTHREADED CAPS WELDED
® TO PSP SADDLE TAP
6"STD
SECTION THROUGH DUCT - BOOT TAP
4" - 14"
4" - 14"
SS CAST RING
EZ CLAMP
4" - 100"
16" - 120"
BI ANGLE RING
SS ANGLE RING
45°
ACCESSORIES
REV: 12/01/19 CAT060EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
60®
HOST DUCT I.D., PRESSURECLASS & MATERIAL TYPE
( REQUIRED INFORMATION )
D1
SECTION THROUGH DUCT - HOT TAP
6"STD
Field Installed Hot Tap
NOTES
Refer to Fab-Tech's INSTALLATION AND ASSEMBLY GUIDEfor assembly instructions.
®Fab-Tech's PSP Field Installed Hot Tapwill allow a new branch to be installed inan existing system without shutting downthe exhaust system.
Only straight tap available for this tap configuration.
4" - 14"SS CAST RING
4" - 24"
4" - 24"
BI ANGLE RING
SS ANGLE RING
WITH JOINT SYSTEM
All fittings with standard Fab-Tech connections include gasketsand clamps or hardware as required for installation.
D2 Host Duct
Anchor Bolt
Backing Ring
End Cap
Fluoropolymer CoatedThreaded Caps Weldedto Backing Ring
PTFE Gasket
Isolation box required for installation.
10
12
14
16
18
20
22
24
26
28
30
32
34
36
4 6 8 10 12 14 16 18 20 22 24
Host
Duct
Dia
.
Tap Dia.
Allowable Tap Sizes
REV: 12/01/19 CAT061EC
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
61 ACCESSORIES
Cast Ring
T RING THICKNESS (SEE CHART)
W
DUCTDIA"D"
H RING HEIGHT (SEE CHART)
RINGWIDTH
# H
OL
ES
BO
LT
HO
LE
SIZ
E
468
10
12
DU
CT
DIA
"D"
3/87/16
x11/16
6
8
12
5.317.509.5011.50
13.81
BO
LT
SIZ
E
BO
LT
CIR
CL
ED
IA.
WID
TH
(W)
1-1/4
HE
IGH
T(H
)
13/32
CAST RING SPECIFICATIONS
1-1/2 1/2 1/29/16
x3/4
TH
ICK
NE
SS
(T)
1/8
3/16
NOTES:
Cast rings available in stainless.
Refer to chart for standard cast rings.
468
10
12
DU
CT
DIA
"D"
RC04 4"
PART NO.DUCTDIA.DESCRIPTION
STEEL CAST RINGRC06 6"
STEEL CAST RING
RC08 8"STEEL CAST RING
RC10 10"STEEL CAST RING
RC12 12"STEEL CAST RING
RC14 14”STEEL CAST RING
14 1415.81
All fittings with standard Fab-Tech connectionsinclude gaskets and clamps or hardware asrequired for installation.
®
REV: 12/01/19 CAT062ED
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
62®
T RING THICKNESS
W
DUCTDIA"D"
W RING WIDTH
ACCESSORIES
Angle Ring
NOTES:
Standard mounting hole locations for welded(fixed) angle rings straddle the vertical centerlineunless otherwise specified.
Refer to chart for standard angle rings.
OPTIONS:
Custom hole pattern and orientation available.
4" - 120"
16" - 120"
BI ANGLE RING
SS ANGLE RING
# H
OL
ES
BO
LT
HO
LE
SIZ
E
14161820222426283032343638404244464850525456586062646668707274767880828486889092949698
100102104106108110112114116118120
DU
CT
DIA
"D"
9/16x
3/4
116
12
16
20
24
28
32
36
40
44
48
52
56
60
64
68
72
76
80
15.8117.7619.7621.7623.8825.8827.8829.8831.8833.8835.8837.8840.3842.3844.3846.3848.3850.3852.8854.8856.8858.8860.8862.8864.8866.8868.8870.8872.8874.8876.8878.8880.8882.8884.8886.88
112
108
104
100
96
92
88
8489.3891.3893.3895.3897.38
100.38102.38104.38106.38108.38110.38112.38114.38116.38118.38120.38122.38124.38
BO
LT
SIZ
E
BO
LT
CIR
CL
ED
IA.
WID
TH
(W)
4
2
3
TH
ICK
NE
SS
(T)
3/16
1/4
ANGLE RING SPECIFICATIONS
2-1/2
1-1/2
468
1012
3/87/16x
11/16
6
8
5.317.509.5011.5013.81
1-1/41/8
1 7/16
SLOT
1/2
14161820222426283032343638404244464850525456586062646668707274767880828486889092949698
100102104106108110112114116118120
DU
CT
DIA
"D"
468
1012
All fittings with standard Fab-Tech connections includegaskets and clamps or hardware as required forinstallation.
REV: 12/01/19 CAT063EC
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
63
FASTENER NUT
CLAMP
FLOATINGBACKING
RING
DUCT
CL004KT
CL004
4"
4"
PART NO. DUCT DIA.DESCRIPTION
4" CLAMP KIT
4" CLAMP
CL006KT 6"6" CLAMP KIT
CL006 6"6" CLAMP
CL008KT 8"8" CLAMP KIT
CL008 8"8" CLAMP
DUCT
FLOATINGBACKING
RING
CROSS SECTION OF
The PSP-EZ™ joining system®
is available for standard PSPduct from 2" to 14" in diameter.The combination of half roundbacking rings and the uniqueangled clamp band providesexcellent clamping force withthe added benefit of ease ofinstallation.
Each Kit above contains a clamp, PTFE tapegasket, and two backing rings
CL002KT
CL003KT
2"
3"
PART NO. DUCT DIA.DESCRIPTION
2" CLAMP KIT
3" CLAMP KIT
CL002 2"2" CLAMP
CL003 3"3" CLAMP
GAS11 2"2" GASKET
GAS13 3"3" GASKET
DIE CUT GASKET
FASTENER NUT
4"-14" PSP-EZ™ JOINT
CLAMP
DUCTDUCT
DUCTFLANGE
Each Kit above contains a clamp and PTFE diecut gasket
CROSS SECTION OF2" & 3" PSP-EZ™ JOINT
CLAMP
CLAMP
ACCESSORIES
PSP-EZ™ Clamp Kit
DUCTFLANGE
NOTE
All fittings with standard Fab-Tech connections includegaskets and clamps or hardware as required for installation.
®
CL010KT
CL010
10"
10"
10" CLAMP KIT
10" CLAMP
CL012KT 12"12" CLAMP KIT
CL012 12"12" CLAMP
CL014KT 14"14" CLAMP KIT
CL014 14"14" CLAMP
2" & 3" EZ FITTINGS
REV: 12/01/19 CAT064EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
64®
Product Guide
2" & 3"PSP-EZ™ CLAMP
STRAIGHT DUCT4' LENGTH ORCUSTOM
PAGE:65SIZE:2" & 3"
ECCENTRICADAPTER
PAGE:67
MICROADJUSTABLEDAMPER
PAGE:69SIZE:2" & 3"
FIELD INSTALLSTRAIGHT DUCTFLANGE
PAGE: 70SIZE:2" & 3"
END CAP
PAGE:68SIZE:2" & 3"
4" TO 2", 4" TO 3"
LATERAL - 45°
PAGE: 66SIZE:2" & 3"
REDUCING TEE
PAGE:65SIZE:3" TO 2"
STRAIGHT TEE
PAGE: 65SIZE: 2" & 3"
VAN STONE TOEZ FLANGEADAPTER
PAGE: 68
CONCENTRICADAPTER
PAGE:68
ELBOW90°
PAGE:66SIZE:2" & 3"
SIZE: 3" TO 2"4" TO 2", 4" TO 3"SIZE: 3" TO 2"
4" TO 2", 4" TO 3"SIZE: 3" TO 2"
DOUBLE TEE
PAGE: 66SIZE: 2" & 3"
ELBOW45°
PAGE:67SIZE:2" & 3"
ELBOW30°
PAGE: 67SIZE:2" & 3"
BLASTGATE
PAGE:71SIZE:2" & 3"
2" & 3" EZ FITTINGS
REV: 12/01/19 CAT065EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
65
All fittings with standard Fab-Tech connections include gaskets and clamps or hardware as required for installation.
All fittings with standard Fab-Tech connections include gaskets and clamps or hardware as required for installation.
02T02
03T03
2"
3"
2" 3.12" 3.12"
3" 3.37" 3.37"
6.24"
6.74"
PART NO. "D1" "L2""D2" "L1" "L3"DESCRIPTION
2" LINE WITH 2" TEE
3" LINE WITH 3" TEE
All fittings with standard Fab-Tech connections include gaskets and clamps or hardware as required for installation.
PZP002
PZS002
PZP003
47.25"
CUSTOM
47.25"
2"
2"
3"
PART NO. "D" "L"DESCRIPTION
2" LINE
2" LINE CUSTOM LENGTH
3" LINE
"D"
"L"
PZS003 CUSTOM3"3" LINE CUSTOM LENGTH
"D1"
"L1"
"L3"
"L2""D2"
EZ Straight
EZ Tee
EZ Reducing Tee
"D1"
"L1"
"L3"
"L2""D2"
03T02 2"3" 3.37" 3.62"6.74"
PART NO. "D1" "L2""D2" "L1" "L3"DESCRIPTION
3" LINE WITH 2" TEE
®
REV: 12/01/19 CAT066EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
66®
"D"
"L"
"L"
R
PZE02
PZE03
2"
3"
2"
3"
3.12"
4.62"
PART NO. R"D" "L"DESCRIPTION
2" 90º ELBOW
3" 90º ELBOW
2" & 3" EZ FITTINGS
90° EZ Elbow
"L2" "L1"
"L1"
45°"D1"
02Y02
03Y03
2"
3"
2" 2.00"
3" 2.03"
7.50"
9.31"
PART NO. "D1" "L2""D2" "L1"DESCRIPTION
2" LINE WITH 2" LATERAL
3" LINE WITH 3" LATERAL
"D2"
EZ Lateral
2T2T2 2"2" 3.12" 3.12"6.24"
PART NO. "D1" "L2""D2" "L1" "L3"DESCRIPTION
2" LINE W/ DOUBLE 2" TEE
"D1"
"L1"
"L3"
"L2""D2"
EZ Double Tee
All fittings with standard Fab-Tech connections include gaskets and clamps or hardware as required for installation.
All fittings with standard Fab-Tech connections include gaskets and clamps or hardware as required for installation.
All fittings with standard Fab-Tech connections include gaskets and clamps or hardware as required for installation.
REV: 12/01/19 CAT067EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
67
"D2""L2"
"L1"
"D1"
3"
4"
4"
2" 0.50"
2" 1.00"
3" 0.50"
8.25"
12.75"
8.00"
"D1" "L2""D2" "L1"
PEA32F
PEA42F
PEA43F
PART NO. DESCRIPTION
2" TO 3" ECCENTRIC
2" TO 4" ECCENTRIC
3" TO 4" ECCENTRIC
2" & 3" EZ FITTINGS
Eccentric EZ Reducer
"D"
"L"
"L"
R
PZ302
PZ303
2"
3"
2"
3"
1.94"
2.38"
PART NO. R"D" "L"DESCRIPTION
2" 30º ELBOW
3" 30º ELBOW
30° EZ Elbow
"D"
"L"
"L"
R
PZ502
PZ503
2"
3"
2"
3"
1.37"
2.00"
PART NO. R"D" "L"DESCRIPTION
2" 45º ELBOW
3" 45º ELBOW
45° EZ Elbow
All fittings with standard Fab-Tech connections include gaskets and clamps or hardware as required for installation.
All fittings with standard Fab-Tech connections include gaskets and clamps or hardware as required for installation.
All fittings with standard Fab-Tech connections include gaskets and clamps or hardware as required for installation.
®
REV: 12/01/19 CAT068EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
68®
PZC02
PZC03
2"
3"
PART NO. "D"DESCRIPTION
2" END CAP
3" END CAP
0.21"
0.21"
"L"
"L"
2" & 3" EZ FITTINGS
"D"
EZ End Cap
4.31"
5.31"
5.31"
5.06"
6.06"
6.06"
"D3" O.D. "D4" DIA.
"D1"
"D2"
"L1"
"D3"
"D4"BOLT CIRCLE DIA.
PCA32R
PCA42R
PCA43R
PART NO. DESCRIPTION
2" TO 3" ANGLE RING
2" TO 4" ANGLE RING
3" TO 4" ANGLE RING
3"
4"
4"
2"
2"
3"
4.25"
3.88"
4.25"
"D1" "D2" "L1"
Angle Ring to EZ Reducer
"D1"
"D2"
"L1"
PCA32F
PCA42F
PCA43F
PART NO. DESCRIPTION
2" TO 3" CONCENTRIC
2" TO 4" CONCENTRIC
3" TO 4" CONCENTRIC
3"
4"
4"
2"
2"
3"
4.31"
3.94"
4.31"
"D1" "D2" "L1"
Concentric EZ Reducer
All fittings with standard Fab-Tech connections include gaskets and clamps or hardware as required for installation.
All fittings with standard Fab-Tech connections include gaskets and clamps or hardware as required for installation.
All fittings with standard Fab-Tech connections include gaskets and clamps or hardware as required for installation.
REV: 12/01/19 CAT069EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
69
"D"
"L"
PZD02
PZD03
2"
3"
3.875"
3.875"
PART NO. "D" "L"DESCRIPTION
2" EZ-DAMPER
3" EZ-DAMPER
ACTUATORPLATE
POSITION LOCK
THUMB WHEEL
FRICTION WHEEL
2" & 3" EZ FITTINGS
Micro-Adjustable EZ Damper
All fittings with standard Fab-Tech connections include gaskets and clampsor hardware as required for installation.
®
REV: 12/01/19 CAT070EC
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
70®
DUCT"D"
"O" RING
AUXILIARYFLANGE
PRESSEDBEAD
"L1"
REPLACEMENT FLANGE FOR 2" & 3" STRAIGHT DUCT MODIFIEDOR CUT TO LENGTH IN THE FIELD
REFER TO INSTALLATION AND ASSEMBLY GUIDE
HTB02
HTB03
2"
3"
2"
2"
PART NO. "D" "L1"DESCRIPTION
2" FIELD FLANGE
3" FIELD FLANGE
2" & 3" EZ FITTINGS
Field Installed Straight Duct EZ Flange
NOTES
Requires purchase of Pressing Wheel, Part #D0700 for installation.The pressing wheel is used to press a bead around the duct tocomplete the installation. Wheel fits Ridgid Pipe Cutter Model 3S.Refer to Fab-Tech's INSTALLATION AND ASSEMBLY GUIDEfor assembly instructions.
PermaShield fluoropolymer barrier coating on interior and exteriorsurfaces.
FOR USE ON EZ STRAIGHT DUCT ONLYNOT DESIGNED FOR EZ ELBOWS, TEES, OR REDUCERS
All fittings with standard Fab-Tech connections includegaskets and clamps or hardware as required for installation.
REV: 12/01/19 CAT071EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
71®
8.5"
PZB02H 2" 8.000”
PART NO. "D" "L"DESCRIPTION
2" EZ-BLASTGATE HORIZONTAL
EZ Blastgate
"D"
SPECIFICATIONS
Stainless steel frame material.
Blade lockout system.
"L"
8.5"
PZB03H 3" 8.000”3" EZ-BLASTGATE HORIZONTAL
"D"
"L"
PZB02V 2" 8.000”
8.000”
PART NO. "D" "L"DESCRIPTION
2" EZ-BLASTGATE VERTICAL
PZB03V 3"3" EZ-BLASTGATE VERTICAL
8.5"
NOTE
All fittings with standard Fab-Tech connections includegaskets and clamps or hardware as required for installation.
2" & 3" EZ FITTINGS
FAB-TECH FLANGE SYSTEM
REV: 12/01/19 CAT072EC
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
72®
NPT MALENIPPLE ADAPTER
2" & 3"2" TO KF 252" TO KF 402" TO KF 50
2" TO 1/8" NPT2" TO 1/4" NPT2" TO 3/8" NPT2" TO 1/2" NPT2" TO 3/4" NPT2" TO 1" NPT
2" TO 1-1/2" NPT2" TO 2" NPT3" TO 3" NPT4" TO 4" NPT
DWYERPITOTADAPTER
79
NPT FEMALENIPPLEADAPTER
2" TO 1/8" NPT2" TO 1/4" NPT2" TO 3/8" NPT2" TO 1/2" NPT2" TO 3/4" NPT2" TO 1" NPT
2" TO 1-1/2" NPT2" TO 2" NPT
®SWAGELOKADAPTER
®2" TO 1/8" SWAGELOK
®2" TO 1/4" SWAGELOK
®2" TO 3/8" SWAGELOK®2" TO 1/2" SWAGELOK®2" TO 3/4" SWAGELOK
PAGE:
74PAGE:78PAGE:
76PAGE:
77PAGE:
75PAGE:
SIZE:SIZE:
SIZE:SIZE:2" & 3"
SPRINKLERADAPTER
SIZE: SIZE:
KF FLANGEADAPTER
FIELD INSTALLEDFAB-TECHFLANGE
2" ONLY
80PAGE:
SIZE:
WELDEDFAB-TECHFLANGE
2" & 3"
73PAGE:
SIZE:
FIELD INSTALLEDFAB-TECH FLANGESADDLE TAP
81PAGE:
SIZE:2" & 3"
Duct
Product Guide
FAB-TECH FLANGE SYSTEM
REV: 12/01/19 CAT073EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
73
FTFL2
FTFL3
2"
3"
PART NO. "D"DESCRIPTION
2" FT FLANGE
3" FT FLANGE
.75"
.75"
"L"
DUCT
FAB-TECH FLANGE( WELDED TO DUCT )
CLAMP
FAB-TECHFLANGE
EZ DUCTOR ADAPTER
"L"
DUCT"D"
Fab-Tech Flange
KF Flange Adapter NPT Female Coupler ®SWAGELOK Adapter
NOTES
Refer to Fab-Tech's INSTALLATION AND ASSEMBLY GUIDEfor assembly instructions.
Fab-Tech Flange / Test Port may be installed on fittingsother than straight duct.
PermaShield fluoropolymer barrier coating on insidesurface and flange faces.
Refer to the EZ fittings section for duct or the Fab-TechFlange system section for adapters to attach to theFab-Tech Flange.
NPT Male Nipple Sprinkler AdapterDwyer Pitot Adapter
ADAPTERS AVAILABLE FOR THE FT FLANGE:
All fittings with standard Fab-Tech connections includegaskets and clamps or hardware as required for installation.
®
FAB-TECH FLANGE SYSTEM
REV: 12/01/19 CAT074EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
74®
KF Flange Adapter
FTK25
FTK40
25mm
40mm
PART NO. KFDESCRIPTION
2" TO 25 KF FLANGE
2" TO 40 KF FLANGE
"L1"
KF 50
2"
2"
"D"
1.25"
1.25"
"L1"
FTK50 50mm2" TO 50 KF FLANGE 2" 1.25"
KF 40KF 25
"D" "D" "D"
NOTES
Refer to Fab-Tech's INSTALLATION AND ASSEMBLY GUIDEfor assembly instructions.
KF Adapters are only available for 2" Fab-Tech Flangeconnection.
PermaShield fluoropolymer barrier coating on inside surfaceand flange faces.
All fittings with standard Fab-Tech connections includegaskets and clamps or hardware as required for installation.
FAB-TECH FLANGE SYSTEM
REV: 12/01/19 CAT075EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
75
NPT Male Nipple Adapter
FTN01
FTN15
2"
2"
PART NO. "D"DESCRIPTION
2" TO 1" NPT
2" TO 1.5" NPT
1" NPT
1.5" NPT
PIPE THREAD
1.25"
1.25"
"L1"
FTN02 2"2" TO 2" NPT 2" NPT 2.25"
FTN03 3"3" TO 3" NPT 3" NPT 2.50"
FTN04** 4"4" TO 4" NPT 4" NPT 3.00"
FTN14
FTN38
2"
2"
2" TO 1/4" NPT
2" TO 3/8" NPT
1/4" NPT
3/8" NPT
1.25"
1.25"
FTN12 2"2" TO 1/2" NPT 1/2" NPT 1.25"
FTN34 2"2" TO 3/4" NPT 3/4" NPT 1.25"
"L1"
"L1""L1"
"L1"
"L1"
"D"
FTN18 2"2" TO 1/8" NPT 1/8" NPT 1.25"
FTN18 FTN14 FTN38
NOTES
Refer to Fab-Tech's INSTALLATION AND ASSEMBLY GUIDEfor assembly instructions.
NPT nipples are not covered under warranty other than fordefects in manufacture. NPT threads are not coated andsince the threads could possibly come in direct contact withcorrosive fumes and fluids, Fab-Tech offers only a limitedwarranty for these parts. Depending on the specificapplication, NPT adapters should fall into the classificationof consumable parts.
PermaShield fluoropolymer barrier coating on inside surfaceand flange face.
"D" "D" "D" "D" "D" "D"
"D" "D" "D"
FTN04FTN03
FTN02
FTN15
FTN01FTN34FTN12
USED WITH 4" PSP-EZ™ TAP
**USED WITH 4" PSP-EZ™ TAP
All fittings with standard Fab-Tech connections includegaskets and clamps or hardware as required for installation.
®
FAB-TECH FLANGE SYSTEM
REV: 12/01/19 CAT076EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
76®
PART NO. "D"DESCRIPTION PIPE THREAD "L1"
FTF01
FTF15
2"
2"
2" TO 1" NPT
2" TO 1.5" NPT
1" NPT
1.5" NPT
1.25"
1.25"
FTF02 2"2" TO 2" NPT 2" NPT 1.25"
FTF38 2"2" TO 3/8" NPT 3/8" NPT .75"
FTF12 2"2" TO 1/2" NPT 1/2" NPT .75"
FTF34 2"2" TO 3/4" NPT 3/4" NPT .75"
FTF14 2"2" TO 1/4" NPT 1/4" NPT .75"
FTF18 2"2" TO 1/8" NPT 1/8" NPT .75"
NPT Female Coupler Adapter
"L1"
FTF18
"D"
FTF14 FTF38
FTF34
FTF01 FTF15 FTF02
"L1"
"D" "D"
"D" "D" "D" "D"
NOTES
Refer to Fab-Tech's INSTALLATION AND ASSEMBLY GUIDEfor assembly instructions.
NPT nipples are not covered under warranty other than fordefects in manufacture. NPT threads are not coated andsince the threads could possibly come in direct contact withcorrosive fumes and fluids, Fab-Tech offers only a limitedwarranty for these parts. Depending on the specificapplication, NPT adapters should fall into the classificationof consumable parts.
PermaShield fluoropolymer barrier coating on flange face.
FTF12
"D"
"L1"
All fittings with standard Fab-Tech connections includegaskets and clamps or hardware as required for installation.
REV: 12/01/19 CAT077EB
FAB-TECH FLANGE SYSTEM
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
77
PART NO. "D"DESCRIPTION THREAD "L1"
FTS38 2"®2" TO 3/8" SWAGELOK 9/16-18 .65"
FTS12 2"®2" TO 1/2" SWAGELOK 3/4-16 .77"
FTS34 2"®2" TO 3/4" SWAGELOK 1-1/16-12 .77"
FTS14 2"®2" TO 1/4" SWAGELOK 7/16-20 .59"
®Swagelok Adapter
NOTES
Refer to Fab-Tech's INSTALLATION AND ASSEMBLY GUIDEfor assembly instructions.
®SWAGELOK Adapters are not covered under warranty other®than for defects in manufacture. SWAGELOK threads are not
coated and since the threads could possibly come in directcontact with corrosive fumes and fluids, Fab-Tech offers only alimited warranty for these parts. Depending on the specific
®application, SWAGELOK adapters should fall into theclassification of consumable parts.
PermaShield fluoropolymer barrier coating on flange face.
"D" "D" "D"
"D"
FTS14 FTS38 FTS12
FTS34
"L1"
"L1"
"L1""L1"
FTS18** 2"®2" TO 1/8" SWAGELOK
**FTS18 IS AVAILABLE AS A CUSTOM ADAPTER, NOT A STOCK ITEM
All fittings with standard Fab-Tech connections includegaskets and clamps or hardware as required for installation.
®
REV: 12/01/19 CAT078EB
FAB-TECH FLANGE SYSTEM
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
78®
FTPT2
FTPT3
2"
3"
PART NO. "D"DESCRIPTION
2" PITOT FLANGE
3" PITOT FLANGE
0.88"
0.88"
"L1"
VARIES ACCORDING TODIAMETER OF DUCT
(ADJUST AS NEEDED)
CLAMP
FAB-TECHFLANGE
PITOTADAPTER
"O" RING
GASKET
SPLIT FLANGE MOUNTING KITDWYER #A-158
DWYER PITOT TUBEDWYER #160-8 TO #160-60
FROM: DWYER INSTRUMENTSwww.dwyer-inst.com
ALIGN PITOT TUBETO CENTER OF DUCTBY ADJUSTING TOMARKINGS ON TUBE
"L1"
Dwyer Pitot Adapter
NOTES
Refer to Fab-Tech's INSTALLATION AND ASSEMBLY GUIDEfor assembly instructions.
PermaShield fluoropolymer barrier coating on inside surfaceand flange faces.
"L1"
FTPT2 FTPT3
"D" "D"
GASKET GASKET
All fittings with standard Fab-Tech connections includegaskets and clamps or hardware as required for installation.
REV: 12/01/19 CAT079EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
79 FAB-TECH FLANGE SYSTEM
Sprinkler Adapter
FTSP2
FTSP3
2"
3"
PART NO. "D"DESCRIPTION
2" SPRINKLER FLANGE
3" SPRINKLER FLANGE
1.10"
2.00"
"L1"
1" NPT
CLAMP
GASKET
FAB-TECHFLANGE
"O" RING(SECONDARY SEAL AND TO HOLD BAG IN PLACE)
SPRINKLER HEAD(SPRINKLER HEAD AND BAG
SUPPLIED BY OTHERSCALL FOR DETAILS)
WATER SUPPLYCONNECTION
"D"DUCT
BAG USED TO PREVENTCORROSION OFSPRINKLER HEAD
NOTES
Refer to Fab-Tech's INSTALLATION AND ASSEMBLY GUIDEfor assembly instructions.
PermaShield fluoropolymer barrier coating on flange face ando-ring surfaces.
FTSP2 FTSP3
"D""D"
"L1" "L1"
1" NPT
1/2" NPT 1/2" NPT
All fittings with standard Fab-Tech connections includegaskets and clamps or hardware as required for installation.
®
REV: 12/01/19 CAT080EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
80®
FAB-TECH FLANGE SYSTEM
Field Installed 2” Fab-Tech Flange
1.69"
"L1"
FTFL2FI 2"
PART NO. "D"DESCRIPTION
2" FIELD FLANGE
LOCKING RING
"L1"
LOCKINGRING
DUCT(10" DIA MIN)
GASKET
HOST DUCT DIAMETER
10" DIAMETER MINIMUM
"D"
NOTES
Refer to Fab-Tech's INSTALLATION AND ASSEMBLY GUIDEfor assembly instructions.
Requires Hydraulic Punch & Swage Kit (TPSO2) toinstall - check accessories section.
PermaShield fluoropolymer barrier coating on inside surfaceand flange faces.
Requires disassembly of duct to install this fitting.
"D"
All fittings with standard Fab-Tech connections includegaskets and clamps or hardware as required for installation.
REV: 12/01/19 CAT081EB
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
81
PZQ02 6" MIN
PART NO. "D2"DESCRIPTION
2" EZ-TAP
"D1"
2"STD
SECTION THROUGH DUCT
"D2" HOST DUCT
STUDS AND NUTS
EXTERIOR SADDLE
PTFE GASKET
THREADED AND COATED CAPS® WELDED TO PSP SADDLE TAP
EXTERIORSADDLE
INTERIORSADDLE
INTERIOR SADDLE
"D1"
2"
PZQ03 8" MIN3" EZ-TAP 3"
HOST DUCT I.D., WALLTHICKNESS & MATERIAL TYPE
( REQUIRED INFORMATION )
NOTES
Refer to Fab-Tech's INSTALLATION AND ASSEMBLY GUIDEfor assembly instructions.
®Fab-Tech's field installed PSP saddle tap will allow a new2" diameter branch to be installed in a 6" and larger diameterduct or a new 3" diameter branch to be installed in an 8" andlarger diameter duct without shutting down the exhaust system.
PermaShield fluoropolymer barrier coating on inside surfacesand flange face.
Field Installed Fab-Tech FlangeSaddle Tap
FAB-TECH FLANGE SYSTEM
All fittings with standard Fab-Tech connections include gasketsand clamps or hardware as required for installation.
®
REV: 12/01/19 CAT082EC
RECTANGULAR DUCT
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
82®
RECTANGULARDUCT
STRAIGHT DUCT
PAGE:84
RADIAL ELBOW30°, 45°, 60°, 90°
PAGE: 88
PAGE:88
CONCENTRICTRANSITION
PAGE: 89
CONCENTRICRECTANGULARTO ROUNDTRANSITION
PAGE: 89
STRAIGHT DUCT WITHRECTANGULARCONICAL TAP
PAGE: 85
STRAIGHT DUCT WITHRECTANGULARBOOT TAP
PAGE:85
STRAIGHT DUCTWITH STRAIGHTRECTANGULARTAP
PAGE: 84
STRAIGHT DUCTWITH MULTIPLETAPS
PAGE: 87
STRAIGHT DUCTWITH ROUNDTAP
PAGE:86
STRAIGHT DUCT WITHRECTANGULARLATERAL TAP
PAGE:86
Product Guide
MITERED ELBOW30°, 45°, 60°, 90°
PAGE:90
DOUBLEOFFSET
PAGE: 91
OFFSET
PAGE:91
END CAP
REV: 12/01/19 CAT083EB
RECTANGULAR DUCT
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
83
Mounting Flange Standards
WIDTH
12" - 24"
26" - 36"
38" - 48"
50" - 60"
62" - 72"
74" - 84"
86" - 96"
DUCT
ANGLE IRONMOUNTING
FLANGE
S = STIFFENER ADDEDTABLE BELOW IS FOR STANDARD DUCT LENGTH OF 48-1/4"
3” TO 4”
3” TO 4”
CENTERLINE TO CENTERLINE
CENTERLINETO
CENTERLINE
DUCT WIDTH
NOTESFlange material is stainless steel.The number of holes for the bolt hole pattern is determined from theduct width and depth. Hole to hole distance will be calculated to bebetween 3" to 4". Oblong holes are punched along the flange centerline.Duct width or depth of 98" and larger requires engineering review.Interior stiffeners ( 1” SCH40 pipe ) are welded between duct sides 50" wideor greater. Separate offset stiffeners are used when both duct widthand depth are 50" or greater.
X
X
Angle sizes (X): 1.5”, 2”, 2.5”, and 3.0”
DUCTDEPTH
Angle thickness for all sizes: 3/16”
Flange angle size determinedfrom duct width and system pressure.
GAUGE
12
12
12
12 - S
12 - S
12 - S
12 - S
1.5”
2”
2”
2”
2”
2”
-10” W.G.
DUCT
2”
SIZEANGLE
GAUGE
16
16
16
16 - S
16 - S
16 - S
16 - S
1.5”
2”
2”
2”
2”
2”
-6” W.G.
DUCT
1.5”
SIZEANGLE
GAUGE
12
12
12
12 - S
12 - S
12 - S
12 - S
1.5”
2”
2”
2”
2”
2.5”
-14” W.G.
DUCT
2”
SIZEANGLE
GAUGE
10
10
10
10 - S
10 - S
10 - S
10 - S
2”
3.0”
2”
2”
2.5”
3.0”
-18” W.G.
DUCT
2”
SIZEANGLE
®
REV: 12/01/19 CAT084EB
RECTANGULAR DUCT
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
84®
Straight Duct
"Y"
"L1"
"X"
MAX. 48-1/4"
INTERIOR STIFFENER
LONGER THAN STANDARD LENGTHS AND/OR HIGHERSYSTEM PRESSURES MAY REQUIRE ADDITIONALSTIFFENERS PER SMACNA, CONTACT FAB-TECH FORSPECIFIC GUIDELINES.
OPTIONS
Custom lengths available.Raw end available.Duct width or depth of 98" and larger requiresFab-Tech engineering review and approval.An interior stiffener ( 1" SCH40 pipe ) is added at themidpoint of the flange for duct width or depthof 50" and greater.
Straight Duct with Straight Rectangular Tap
LONGER THAN STANDARD LENGTHS AND/OR HIGHER SYSTEMPRESSURES MAY REQUIRE ADDITIONAL STIFFENERS PERSMACNA, CONTACT FAB-TECH FOR SPECIFIC GUIDELINES.
OPTIONS
Custom lengths available.Raw end available.Duct width or depth of 98" and larger requiresFab-Tech engineering review and approval.An interior stiffener ( 1" SCH40 pipe ) is added at themidpoint of the flange for duct width or depth of 50"and greater.
NOTE
NOTE
"L1" MAX. 48-1/4"
"X"
"Y"
"L2"MIN 6"
MIN 4"
"L3"
MIN 4"
"L4""L4"
"L4"
"L4"
"L4"
"TY"
"TX"
All fittings with standard Fab-Tech connections includegaskets and clamps or hardware as required for installation.
All fittings with standard Fab-Tech connections includegaskets and clamps or hardware as required for installation.
REV: 12/01/19 CAT085EB
RECTANGULAR DUCT
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
85
Straight Duct with Rectangular Boot Tap
LONGER THAN STANDARD LENGTHS AND/OR HIGHER SYSTEMPRESSURES MAY REQUIRE ADDITIONAL STIFFENERS PERSMACNA, CONTACT FAB-TECH FOR SPECIFIC GUIDELINES.
Straight Duct with Rectangular Conical Tap
LONGER THAN STANDARD LENGTHS AND/OR HIGHER SYSTEMPRESSURES MAY REQUIRE ADDITIONAL STIFFENERS PERSMACNA CONTACT FAB-TECH FOR SPECIFIC GUIDELINES.
OPTIONS
Custom lengths available.Raw end available.Duct width or depth of 98" and larger requiresFab-Tech engineering review and approval.An interior stiffener ( 1" SCH40 pipe ) is added at themidpoint of the flange for duct width or depth of 50"and greater.
OPTIONS
Custom lengths available.Raw end available.Duct width or depth of 98" and larger requiresFab-Tech engineering review and approval.An interior stiffener ( 1" SCH40 pipe ) is added at themidpoint of the flange for duct width or depth of 50"and greater.
NOTE
NOTE
"L1" MAX. 48-1/4"
"X"
"Y"
"L2"9" STD MIN 4"
"L3"
MIN 4"
"L4""L4"
"L4"
"L4"
"L4"
"TY"
"TX"
45°6”STD
"L1" MAX. 48-1/4"
"X"
"Y"
"L2"9" STD
MIN 4"
"L3"
MIN 4"
"L4""L4"
"L4"
"L4"
"L4"
"TY"
"TX"
45°6”STD
All fittings with standard Fab-Tech connections include gaskets andclamps or hardware as required for installation.
All fittings with standard Fab-Tech connections include gaskets andclamps or hardware as required for installation.
®
REV: 12/01/19 CAT086EB
RECTANGULAR DUCT
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
86®
Straight Duct with Rectangular Lateral Tap
LONGER THAN STANDARD LENGTHS AND/OR HIGHER SYSTEMPRESSURES MAY REQUIRE ADDITIONAL STIFFENERS PERSMACNA, CONTACT FAB-TECH FOR SPECIFIC GUIDELINES.
Straight Duct with Round Tap
EZ
BI
SC
SS
EZ CLAMPS( AVAILABLE 4" - 14" )STAINLESS CAST RINGS( AVAILABLE 4" - 14" )BLACK IRON ANGLE RINGS( AVAILABLE 4" - 100" )STAINLESS ANGLE RINGS( AVAILABLE 16" - 120" )
ROUND RING TYPES ("R")
OPTIONS
Custom lengths available.Raw end available.Duct width or depth of 98" and larger requires Fab-Techengineering review and approval.An interior stiffener ( 1" SCH40 pipe ) is added at the midpoint ofthe flange for duct width or depth of 50" and greater.
OPTIONS
Custom lengths available.Raw end available.Duct width or depth of 98"and larger requires Fab-Techengineering review and approval.An interior stiffener ( 1" SCH40 pipe ) is added at the midpoint ofthe flange for duct width or depth of 50" and greater.
NOTE
NOTE
LONGER THAN STANDARD LENGTHS AND/OR HIGHER SYSTEMPRESSURES MAY REQUIRE ADDITIONAL STIFFENERS PERSMACNA, CONTACT FAB-TECH FOR SPECIFIC GUIDELINES.
"TY"
6” STD
"TX"
"L2"
45° STD
"L1" MAX. 48-1/4"
"X"
"Y"
"L4""L4"
"L4"
"L4"
"L4"
MIN 4""L3"
MIN 4"
"L1" MAX. 48-1/4"
"R""DØ"
"X"
"Y"
"L2"MIN 6"
MIN 4"
"L3"
MIN 4"
"L4""L4"
"L4"
"L4"
"L4"
All fittings with standard Fab-Tech connections include gasketsand clamps or hardware as required for installation.
All fittings with standard Fab-Techconnections include gaskets andclamps or hardware as requiredfor installation.
REV: 12/01/19 CAT087EA
RECTANGULAR DUCT
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
87
Straight Duct with Multiple Taps
LONGER THAN STANDARD LENGTHS AND/OR HIGHERSYSTEM PRESSURES MAY REQUIRE ADDITIONALSTIFFENERS PER SMACNA, CONTACT FAB-TECH FORSPECIFIC GUIDELINES.
"R""TX"
"TX"
6" STD
4"MIN
4"MIN
1" MIN
6" STD
SHOETAP
"L3"STRAIGHTTAP
"L3"
CONICAL TAP"L3"
ROUND TAP"L3"
45° LATERAL TAP"L3"
"L1"
"L2""L2"
EZ
BI
SC
SS
EZ CLAMPS( AVAILABLE 4" - 14" )
STAINLESS CAST RINGS( AVAILABLE 4" - 14" )
BLACK IRON ANGLE RINGS( AVAILABLE 4" - 120" )
STAINLESS ANGLE RINGS( AVAILABLE 16" - 120" )
ROUND RING TYPES ("R")
"L4"
"X"
"Y"
MIN 6"
"TY"
"TX""TX"
"L5"
"L5"
"L4"
"L2""L2"
"L2"
"L2"
END VIEW
MAX. 48-1/4"
4"MIN
"TX"
TOP
"DØ"
45°
OPTIONS
Custom lengths available.Raw end available.Duct width or depth of 98" and larger requires Fab-Tech engineering review and approval.An interior stiffener ( 1" SCH40 pipe ) is added at the midpoint of the flange for duct width or depth of 50" and greater.
NOTE
All fittings with standard Fab-Tech connections include gaskets andclamps or hardware as required for installation.
®
REV: 12/01/19 CAT088EB
RECTANGULAR DUCT
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
88®
"Y"
"X"
"N"
"L1"
90°, 60°, 45°, 30° or Custom Elbow
30° RADIALELBOW
60° RADIALELBOW
45° RADIALELBOW
90° RADIALELBOW
"X"
"Y"
"L1"
"L2"
"N"
90°, 60°, 45°, 30° or Custom Mitered Elbow
30° MITEREDELBOW
60° MITEREDELBOW
90° MITEREDELBOW
45° MITEREDELBOW
OPTIONS
Raw end available.Duct width or depth of 98" and larger requires Fab-Tech engineeringreview and approval.An interior stiffener ( 1" SCH40 pipe ) is added at the midpoint of theflange for duct width or depth of 50" and greater.
NOTE
All fittings with standard Fab-Tech connections include gaskets andclamps or hardware as required for installation.
REV: 12/01/19 CAT089EA
RECTANGULAR DUCT
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
89
"T1"
"Y""T2"
"X"
"L1"
Concentric Transition
FOR ECCENTRIC RECTANGULARTO RECTANGULAR FITTING, USETHE CUSTOM FITTING ORDERSHEET.
Concentric Rectangular to Round Transition
"Y"
"DØ"
"X" "L1"
3" MIN
"R"
"L2"
FOR ECCENTRIC RECTANGULARTO ROUND FITTING, USE THECUSTOM FITTING ORDER SHEET.
EZ
BI
SC
SS
EZ CLAMPS( AVAILABLE 4" - 14" )
STAINLESS CAST RINGS( AVAILABLE 4" - 14" )
BLACK IRON ANGLE RINGS( AVAILABLE 4" - 120" )
STAINLESS ANGLE RINGS( AVAILABLE 16" - 120" )
ROUND RING TYPES
OPTIONS
Raw end available.Duct width or depth of 98" and larger requires Fab-Tech engineeringreview and approval.An interior stiffener ( 1" SCH40 pipe ) is added at the midpoint of theflange for duct width or depth of 50" and greater.
OPTIONS
Raw end available.Duct width or depth of 98" and larger requires Fab-Tech engineeringreview and approval.An interior stiffener ( 1" SCH40 pipe ) is added at the midpoint of theflange for duct width or depth of 50" and greater.
NOTE
NOTE
All fittings with standard Fab-Tech connections include gaskets andclamps or hardware as required for installation.
All fittings with standard Fab-Tech connections include gaskets andclamps or hardware as required for installation.
®
REV: 12/01/19 CAT090EB
RECTANGULAR DUCT
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
90®
"L1"
"L2"
"X"
"Y"
CENTER OF "Y"TO CENTER OF
OFFSET
Offset
OPTIONS
Raw end available.Duct width or depth of 98" and larger requires Fab-Tech engineeringreview and approval.An interior stiffener ( 1" SCH40 pipe ) is added at the midpoint of theflange for duct width or depth of 50" and greater.
NOTE
All fittings with standard Fab-Tech connections include gaskets andclamps or hardware as required for installation.
REV: 12/01/19 CAT091EA
RECTANGULAR DUCT
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
91
"L3"
"L1"
"L2"
"Y"
"X"
Double Offset
CENTER OF "X"TO CENTER OF
OFFSETCENTER OF "Y"TO CENTER OF
OFFSET
"Y"
"X"
STAINLESS STEELPLATE WELDEDTO FLANGE
End Cap
OPTIONS
Raw end available.Duct width or depth of 98" and larger requires Fab-Tech engineeringreview and approval.An interior stiffener ( 1" SCH40 pipe ) is added at the midpoint of theflange for duct width or depth of 50" and greater.
OPTIONS
Flange material will be stainless steel unless other material is specified.Duct width or depth of 98" and larger requires Fab-Tech engineeringreview and approval.A stiffener ( angle material matching the frame ) is added at the flange midpoint or where aestheticallypleasing for duct width or depth of 50" and greater ( as required to meet maximum 4' spacing ).
NOTE
NOTE
All fittings with standard Fab-Tech connections include gaskets andclamps or hardware as required for installation.
All fittings with standard Fab-Tech connections include gaskets andclamps or hardware as required for installation.
®
REV: 12/01/19 CAT092EA
RECTANGULAR DUCT
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
92®
Product Guide
RECTANGULARCONTROLDEVICES
INDUSTRIALRECTANGULARPARALLEL BLADECONTROL DAMPER
PAGE:94
PAGE:96
INDUSTRIALRECTANGULARINDUSTRIALBACKDRAFTDAMPER
PAGE: 95
INDUSTRIALRECTANGULAROPPOSED BLADECONTROL DAMPER
PAGE: 94
PAGE: 96
HORIZONTALBLASTGATE
PAGE:97
VERTICALBLASTGATE
PAGE: 97
HEAVY DUTYRECTANGULARPARALLEL BLADECONTROL DAMPER
HEAVY DUTYRECTANGULAROPPOSED BLADECONTROL DAMPER
REV: 12/01/19 CAT093EA
RECTANGULAR DUCT
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
93®
Rectangular Damper Chart
36"x36" to 120"x120" HEAVY DUTYCONTROL DAMPERS
COATED 10GA STAINLESS STEEL
ACTUATOR:
FRAME LENGTH:
AXLES:
LOCKOUT:
BLADES:
SHAFT SEALS:
FRAME:
10" STD
FULL OPEN / FULL CLOSE
1.38" DIA. STAINLESS STEELLIQUID TIGHT
FRAME SEALS:PTFE
10GA STAINLESS STEELQUADRANT PLATES:
MOUNTING HOLES:
EXTERNAL LINKAGES:10GA STAINLESS STEEL
10GA STAINLESS STEEL - CENTER SUPPORT WITHLINKAGE REQUIRED FOR BLADES LONGER THAN 36"
JOINING SYSTEM:2" FLANGESCOATING: PERMASHIELD FLUOROPOLYMER BARRIER
GEAR DRIVE WITH LOCKING DAMPER SHAFTPNEUMATIC ACTUATOR
BLANK MOUNTING KIT - PLATE & SHAFT ADAPTEROPTION:
OPTION:OPTION:
MANUAL HANDLE
TWIN DRIVE AS REQUIRED
.562"X.750" SLOTS: 3" TO 4" ON CENTER
.25" STAINLESS STEELQUADRANT LEVER:
ACTUATOR MOUNTING KITOPTION:
8"x8" to 120"x120" INDUSTRIALBACKDRAFT DAMPER
COATED 14GA STAINLESS STEEL
COUNTERWEIGHTS:
FRAME LENGTH:
AXLES:BLADES:
SHAFT SEALS:
FRAME:
8" STD
.50" DIA. STAINLESS STEELLIQUID TIGHT
FRAME SEALS:PTFE
MOUNTING HOLES:
EXTERNAL LINKAGES:10GA STAINLESS STEEL
10GA STAINLESS STEELCENTER SUPPORTS AS REQUIRED
JOINING SYSTEM:2" FLANGESCOATING: PERMASHIELD FLUOROPOLYMER BARRIER
ADJUSTABLE
TWIN DRIVE AS REQUIRED
.44"X.69" SLOTS: < 4" ON CENTER
8"x8" to 36"x36" INDUSTRIALCONTROL DAMPERS
COATED 10GA STAINLESS STEEL
ACTUATOR:
FRAME LENGTH:
AXLES:
LOCKOUT:
BLADES:
SHAFT SEALS:
FRAME:
8" STD
FULL OPEN / FULL CLOSE
.50" DIA. STAINLESS STEELLIQUID TIGHT
FRAME SEALS:PTFE
10GA STAINLESS STEELQUADRANT PLATES:
MOUNTING HOLES:
EXTERNAL LINKAGES:10GA STAINLESS STEEL
10GA STAINLESS STEELCENTER SUPPORTS AS REQUIRED
JOINING SYSTEM:2" FLANGESCOATING: PERMASHIELD FLUOROPOLYMER BARRIER
GEAR DRIVE WITH LOCKING DAMPER SHAFTELECTRIC ACTUATORPNEUMATIC ACTUATOROPTION:
OPTION:OPTION:
MANUAL HANDLE
TWIN DRIVE AS REQUIRED
.44"X.69" SLOTS: < 4" ON CENTER
.25" STAINLESS STEELQUADRANT LEVER:
CUSTOM ACTUATOR MOUNTING KITOPTION:
FOR CUSTOMER SUPPLIED ACTUATOR
PARALLELBLADE
OPPOSEDBLADE
PARALLELBLADE
OPPOSEDBLADE
PARALLEL OR OPPOSED BLADE CONFIG.
PARALLEL OR OPPOSED BLADE CONFIG.
REV: 12/01/19 CAT094EA
RECTANGULAR DUCT
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
94®
"L1" 8"STD
"L2"
Industrial Rectangular Parallel BladeControl Damper
OPTIONS
"L1" 8"STD
"L2"
Industrial Rectangular Opposed BladeControl Damper
Frame 8" standard length with 2" flanges.Mounting holes (.562" x .750" slot)located between 3" to 4" on center.Blades - 10 GA stainless steel.Axles - .50" diameter stainless steel.Liquid tight shaft seals.Linkage located outside theairstream - 10 GA stainless steeltwin drive as required.Quadrant plates - 10 GA stainlesssteel.Quadrant lever - .25" stainless steel.Full open / full close lockouts.PTFE frame seals.
Actuator mounting kits.Blank mounting kit ( plate & shaft adapter ) forcustomer supplied actuator.Pneumatic / electric actuator.Gear drive with locking damper shaft.
SPECIFICATIONS
OPTIONS
Frame 8" standard length with 2" flanges.Mounting holes (.562" x .750" slot)located between 3" to 4" on center.Blades - 10 GA stainless steel.Axles - .50" diameter stainless steel.Liquid tight shaft seals.Linkage located outside theairstream - 10 GA stainless steeltwin drive as required.Quadrant plates - 10 GA stainlesssteel.Quadrant lever - .25" stainless steel.Full open / full close lockouts.PTFE frame seals.
SPECIFICATIONS
NOTE
NOTE
All fittings with standard Fab-Tech connectionsinclude gaskets and clamps or hardware asrequired for installation.
All fittings with standard Fab-Tech connectionsinclude gaskets and clamps or hardware asrequired for installation.
Actuator mounting kits.Blank mounting kit ( plate & shaft adapter ) forcustomer supplied actuator.Pneumatic / electric actuator.Gear drive with locking damper shaft.
FOR "L1" OR "L2" LONGER THAN 36"HEAVY DUTY DAMPER IS REQUIRED
FOR "L1" OR "L2" LONGER THAN 36"HEAVY DUTY DAMPER IS REQUIRED
REV: 12/01/19 CAT095EA
RECTANGULAR DUCT
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
95®
"L1" 8"STD
"L2"
SPECIFICATIONS
10 GA stainless steel frame8" std length with 2" flangescenter support as required.
Manual adjustablecounterweights.
Flange mounting holes( .562" X .750" slot ) equal toor less than 4" on center.14 GA stainless steel blades..50" diameter stainless steelaxles.Liquid tight shaft seals.All linkages 10 GA stainlesssteel outside airstream.
CENTER SUPPORT REQUIRED FORBLADES LONGER THAN 36" ( "L1" )
COUNTERWEIGHT
PTFE frame seals.
Industrial Rectangular Backdraft Damper
All fittings with standard Fab-Techconnections include gaskets andclamps or hardware as requiredfor installation.
NOTE
RECTANGULAR DUCT 96®
REV: 12/01/19 CAT096EA
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
CENTER SUPPORT W/ CENTER LINKAGEREQUIRED FOR BLADES LONGER THAN 36" ("L1").
10"STD
"L2"
Heavy Duty Rectangular Parallel BladeControl Damper
OPTIONS
"L2"
Heavy Duty Rectangular Opposed BladeControl Damper
Frame 10" standard length with 2" flanges.Mounting holes (.562" x .750" slot)located between 3" to 4" on center.Blades - 10 GA stainless steel.Axles - 1.38" diameter stainless steel.Liquid tight shaft seals.Linkage located outside theairstream - 10 GA stainless steeltwin drive as required.Quadrant plates - 10 GA stainlesssteel.Quadrant lever - .25" stainless steel.Full open / full close lockouts.PTFE frame seals.
Actuator mounting kits.Blank mounting kit ( plate & shaft adapter ) forcustomer supplied actuator.Pneumatic / electric actuator.Gear drive with locking damper shaft.
SPECIFICATIONS
OPTIONS
Frame 10" standard length with 2" flanges.Mounting holes (.562" x .750" slot)located between 3" to 4" on center.Blades - 10 GA stainless steel.Axles - 1.38" diameter stainless steel.Liquid tight shaft seals.Linkage located outside theairstream - 10 GA stainless steeltwin drive as required.Quadrant plates - 10 GA stainlesssteel.Quadrant lever - .25" stainless steel.Full open / full close lockouts.PTFE frame seals.
SPECIFICATIONS
NOTE
NOTE
All fittings with standard Fab-Tech connectionsinclude gaskets and clamps or hardware asrequired for installation.
All fittings with standard Fab-Tech connectionsinclude gaskets and clamps or hardware asrequired for installation.
Actuator mounting kits.Blank mounting kit ( plate & shaft adapter ) forcustomer supplied actuator.Pneumatic / electric actuator.Gear drive with locking damper shaft.
CENTER SUPPORT W/ CENTER LINKAGEREQUIRED FOR BLADES LONGER THAN 36" ("L1").
"L1" 10"STD
"L1"
REV: 12/01/19 CAT097EA
RECTANGULAR DUCT
"L1"
8"STD
CENTER SUPPORT REQUIRED FOR BLADES LONGER THAN 36" ( "L1" )
Horizontal Blastgate
SPECIFICATIONSStainless steel body, rings and blades.Blade lockout system.
PTFE WIPER( TYP BOTHSIDES OFBLADE)
"L2"
BLADE
COLLAR
BODY
SPACER
BLADELOCKOUT(STD)
8"STD
Vertical Blastgate
PTFE WIPER( TYP BOTHSIDES OFBLADE)
BLADE
COLLAR
BODY
SPACER
BLADELOCKOUT(STD)
"L1"
"L2"
Fab-Tech, Inc. / 480 Hercules Drive, Colchester, VT 05446 / Tel: 802-655-8800 / Fax: 802-655-8804 / www.fabtechinc.com
97®
CENTER SUPPORT REQUIRED FOR BLADES LONGER THAN 36" ( "L1" )
SPECIFICATIONSStainless steel body, rings and blades.Blade lockout system.All fittings with standard Fab-Tech connections include gasketsand clamps or hardware as required for installation.
All fittings with standard Fab-Tech connections include gasketsand clamps or hardware as required for installation.