Copyright © 2002 Delmar Thomson Learning Chapter 6 Introduction to Logic.
-
Upload
cora-willis -
Category
Documents
-
view
224 -
download
3
Transcript of Copyright © 2002 Delmar Thomson Learning Chapter 6 Introduction to Logic.
Copyright © 2002 Delmar Thomson Learning
Chapter 6
Introduction to Logic
Copyright © 2002 Delmar Thomson Learning
Objectives
Explain AND logic.Describe OR logic.Explain NOT logic.Explore a truth table for specified
logic.Determine if a PLC ladder rung is
true or false under specified conditions.
Copyright © 2002 Delmar Thomson Learning
Hardwired Electrical Circuit Has Electrical Continuity
Hardwired circuit has actual current flow.
This is called electrical continuity.Current flows through switching
device to directly control the load.
Copyright © 2002 Delmar Thomson Learning
Hardwired Relay Circuit
Copyright © 2002 Delmar Thomson Learning
Logical Continuity
Hardwire relay circuits have electrical continuity, or current flow.
PLCs do not operate on electrical continuity, but logical continuity.
Copyright © 2002 Delmar Thomson Learning
Logical Continuity (cont’d.)
A PLC ladder program resembles an electric schematic.
A PLC program is a set of instructions stored in memory.
PLC ladder symbols represent ladder program instructions.
Copyright © 2002 Delmar Thomson Learning
Logical Continuity (cont’d.)
PLC instructions examine the status of a bit at the associated address.
Bits are either a 1 or 0.Instructions are either true or
false.PLCs have logical continuity.
Copyright © 2002 Delmar Thomson Learning
Signal Flow into and out of a PLC
Copyright © 2002 Delmar Thomson Learning
Input Signal Seen by Input Module
Signal from field device is wired to input module screw terminals.
These signals are called input signals or simply inputs.
Each input point has a unique identifier called an address.
Copyright © 2002 Delmar Thomson Learning
Input Module Isolates and Converts
Discrete input module determines if input is a valid ON signal.
The discrete input module converts the incoming electrical signal to +5v DC, or 0v DC.
An ON state will be converted to +5v DC.
An OFF state will be converted to 0v DC.
Copyright © 2002 Delmar Thomson Learning
Input Section to Back Plane
The high voltage input signal is isolated from the lower voltage microprocessor and supporting circuitry in the processor.
Signal is then transferred to the chassis back plane and sent to processor memory for storage.
Copyright © 2002 Delmar Thomson Learning
Processor and Input Status File
Field input signals are transferred from the input module by way of the back plane for storage in the processor’s input status file.
There is one storage location in the status table for the on or off status of each input device.
On signal stored as a 1, off as a 0.
Copyright © 2002 Delmar Thomson Learning
Processor Examines Status Table Bit
When running, the processor solves ladder instructions by examining the on or off status of the input device by examining the associated memory location for a 1 or 0.
Copyright © 2002 Delmar Thomson Learning
Ladder Program Solved
Ladder instructions have rules regarding when they are true or false.
Instructions are made true or false as a result of the examined bit.
If there is a path of true input instructions to the output instruction, the rung will be true.
Copyright © 2002 Delmar Thomson Learning
Output Update
When all ladder rungs have been solved, the output status table data is sent to the respective output modules one word at a time.
When rung is solved, the output status table is updated.
Copyright © 2002 Delmar Thomson Learning
Combining and Solving Ladder Instructions
Three basic types of logic:AndOrAnd / Or (combinational)
Copyright © 2002 Delmar Thomson Learning
Series Logic
When two switches are wired in series, both switches must be ON before power will flow.
Switch 1 AND switch 2 must all pass power before light 1 will turn on.
Copyright © 2002 Delmar Thomson Learning
Conventional Series Circuit
Copyright © 2002 Delmar Thomson Learning
Switch 1 AND Switch 2 Need to Be Closed to Energize L-1
Copyright © 2002 Delmar Thomson Learning
Truth Table
A truth table shows all possible input conditions and the expected output conditions.
The following slide shows a truth table for AND logic.
Copyright © 2002 Delmar Thomson Learning
Truth Table for AND Logic
Copyright © 2002 Delmar Thomson Learning
PLC Instructions in Series
PLC instructions work the same basic way as hard wired field devices.
Instructions in series are considered ANDed together, or AND logic.
Switch 1 AND switch 2 must be on for L-1 to come on.
Copyright © 2002 Delmar Thomson Learning
PLC Representation of a Rung
Copyright © 2002 Delmar Thomson Learning
Truth Table for Two-Input AND Logic
Copyright © 2002 Delmar Thomson Learning
Three-Input Series Circuit
Copyright © 2002 Delmar Thomson Learning
Three-Input PLC Ladder Rung
Copyright © 2002 Delmar Thomson Learning
Three-Input AND Logic Truth Table
Copyright © 2002 Delmar Thomson Learning
Parallel Is also OR Logic
Inputs in parallel are said to be ORed.
Switch 1 is ORed with switch 2.If switch 1 is closed OR switch 2 is
closed, light 1 will turn on.If both SW1 and SW2 are closed,
light 1 will turn on.
Copyright © 2002 Delmar Thomson Learning
Conventional Parallel Circuit
Copyright © 2002 Delmar Thomson Learning
Programmable Controller Ladder Diagram
Copyright © 2002 Delmar Thomson Learning
Two-input OR Truth Table
Copyright © 2002 Delmar Thomson Learning
Truth Table for NOT Logic
Copyright © 2002 Delmar Thomson Learning
Conventional Ladder Diagram
Copyright © 2002 Delmar Thomson Learning
PLC Representation of N.O and N.C. Instructions
All PLCs use the standard normally open and normally closed instructions.
Different manufacturers use different names for the instructions.
Copyright © 2002 Delmar Thomson Learning
Normally Open and Normally Closed Instruction
Identification
Copyright © 2002 Delmar Thomson Learning
Combination AND-OR Logic
Input devices can be combined in series (ANDed) and also in parallel (ORed) on a PLC ladder rung.
Instructions programmed to provide the proper input conditions for your application.
This is called combination AND-OR logic.
Copyright © 2002 Delmar Thomson Learning
Combination AND-OR Logic