Conveyor Technologies Ltd. MODULARConveyor Technologies new guide rail system offers unmatched...
Transcript of Conveyor Technologies Ltd. MODULARConveyor Technologies new guide rail system offers unmatched...
Conveyor Technologies Ltd. The Ultimate In Modular Low Profile Conveyors
M O D U L A R
BENEFITS OF OUR MODULAR GUIDE RAIL SYSTEM
• Optional tool-less adjustment allows operators to change settings.
• All sides can be adjusted laterally and vertically.
• Modular design allows for quick and low cost reconfiguration.
• Industry standard UHMW rail profiles prevent marring product.
• Quick pre-set width adjustment optional.
• 2-axis cross blocks are guided to prevent rotation and binding.
• Extenders permit up to 3" increase in width capacity.
• Permits rapid removal and replacement.
SIDE GUIDES • LANE DIVIDERS • HOLD DOWNS • END STOPS
FIXEDGUIDE RAILS
Series S Series TS-A1-A-1-000-1 T-A1-A-1-000-1
2-AXISSCREW ADJUSTABLE GUIDES
Series S Series TS-A2-A-1-000-1 T-A2-A-1-000-1
“D” Distance Between Rails with 6” Rod
Rail Type Series S Series TMin. Max. Min. Max
A-E W -10.22 W -.14 W -9.60 W +.48
with collars W -9.41 W -.66 W -8.79 W -.04
2-AXIS QUICK SET GUIDESWITH 4" OR 6" ROD
Series S Series TS-A3-E-1-000-1 T-A3-E-1-000-1
“D” Distance Between Rails with 4” Rod
Rail Type Series S Series TMin. Max. Min. Max
A-E W -6.22 W -.14 W -5.60 W +.48
with collars W -5.41 W -.66 W -4.79 W -.04
First .25" inward movement of each side frommaximum is not adjustable
Remove Nut and washer at point “A” for maximum distance.
“H” Values - Vertical Distancefrom Center of Rail to Belt
Bracket Series S Series TPosition “H” Max. “H” Max.
Standard Bracket #1 A-E Rails
Low 1 1/16 7/8
High 1 1/2 2 1/8
Medium Bracket #2 A-G Rails
Low 2 1/8 2 1/8
High 2 3/4 3 3/8
High Bracket #3 A-G Rails
Low 4 1/2 4 1/2
High 5 1/8 5 3/4
“D” Distance Between Rails
Rail Type Series “S” Series “T”Min. Max. Min. Max
A-E W -2.43 W +.17 W -1.81 W +.79
“D” Distance Between Rails
Rail Type Series S Series T
A-F W +.17 W +.79
G W -.08 W +.54
F and G Rails must use Medium or High Bracket
H
WBELT WIDTH
H
WBELT WIDTH
H
WBELT WIDTH
Conveyor Technologies Ltd. • 440 Milford Parkway, Milford, Ohio 45150-9104 • (513) 248-0663 • www.ConveyorTechLtd.com
D D
POINT “A”
D
Conveyor Technologies new guide rail system offers unmatched versatility and ease ofadjustment, in a rugged compact modular package. Optional pre-engineered items suchas lateral preset position stops, tool-less adjustment, lane dividers, diverters, hold-down,width extenders and adjustable end-stops are easily integrated within the modularsystem.
All guide surfaces are equipped with a UHMW liner which is available in a wide rangeof sizes and shapes. This reduces frictional guide drag that contributes to belt mis-tracking, while protecting product surface.
Two-axis rod system utilizes a unique guided, non-rotating cross block design whichcombines rapid adjustment with greater rigidity. This provides freedom frommisalignment and binding associated with cross block mounting on a vertical round shaft.Optional collars permit rapid selection of (2) preset lateral side guide positions. Alladjustments (except collars) can be provided with tool-less adjustment. Three sizes ofmounting brackets allow selection of desired height range and ease of integrating hold-down, lane dividers, diverters, and sensors.
Adjustable end-stops permits rapid tool-less longitudinal positioning and removal.Height of stop bar can be selected for optimum operation.
When additional distance between rails (“D” dimension) is required, width extenderscan be utilized. A set of #3014 extenders afford a total increase of 1.25." This provides
“S” series conveyors with approximately thesame “D” dimension as the “T” series. A set of#2117 extenders allows most end drive con-veyors to carry loads 2" wider than the nom-inal belt width “W.” Center drive conveyorscan have “D” values 3" greater than thoselisted.These extenders in conjunction with ourpatented bearing plate design, and high loadcapacity provide an extremely low costmethod of increasing conveyor width capacity.This can also reduce initial cost and beltreplacement cost.
Adjustment
1 Fixed
2 Screw
3 4” Rod
4 6” Rod
Series
2-Axis QuickSet Options
A None
D 3 Lobe
E 3 Lobe & Ratchet
F 3 Lobe & Collars
G 3 Lobe, Ratchet and Collars
Bracket
0 None
1 Std.
2 Med.
3 High
Length (Inches)
Number of Sides
1 Single Side
2 Set of 2 Sides
T - A - 1 - A - 1 - 000 - 1SIDE GUIDES
Shape Rail Height
A 0.81B 1.00D 1.75E 2.12
F 3.00G* 4.00
H* 0.76
I 0.81
J* 0.72
Q* 0.46
R* round
S* 1.00
Sp
ecia
lO
pti
on
alR
ails
Sta
rnd
ard
Rai
ls
2.10
0.47
*reduces “D” values
“T” Series with 2 axisscrew adjustable guides and#2117 width extenders.
Conveyor Technologies Ltd. • 440 Milford Parkway, Milford, Ohio 45150-9104 • (513) 248-0663 • www.ConveyorTechLtd.com
Series
Rails
Upper Lower
A A
B B
D D
E E
Series
Rod MountStyle
A 1-Side
B 2-Sides
C Common*18-24
RodLength
1 4"
2 6
3 8
4 20.5*
5 26.5*
PositionLock
S Screw
R Ratchet
DividerLength(# in inches)
T - 2 - BB - A - 1 - R - 000
Numberof Lanes
Fill innumber
Rod MountStyle
A 1-Side
B 2-Sides
C Common*18-24
RodLength
1 4"
2 6
3 8
4 20.5*
5 26.5*
PositionLock
S Screw
R Ratchet
T - A - A - 4 - R - 000
Rail
A
B
D
E
PositionLock
S Screw
R Ratchet
Width
# In Inches
(max. distancebetween siderail minus .25")
100255 - A - S - 00.0
StopRail
A
B
D
E
* Common “C” type rod mounts are intended for only 18"-24" conveyors. Each rod requires (2) #2077 cross blocks.
Note: end stop will function on side rails “A” through “E.” Stop can be positioned along length of side rail.
ADJUSTABLE LANE DIVIDER
HOLD-DOWN
END STOP
Hold-DownLength (# in inches)
Vertical position of upper and lower guide rails are adjustable independent of each other.
Nothing extends below lower rail regardless of its position Alternate solid UHMW divider is available. Contact factory.
Topof belt
Topof belt
RodMount
RodMount
RailsA,B,D,E
5.125
H
4.125
1.39
.95
1.93upper
rail max.down
position
.25
RailsA,B,D,E
Conveyor Technologies Ltd. 440 Milford Parkway, Milford, Ohio 45150-9104(513) 248-0663 www.ConveyorTechLtd.com
1.93lower railmax. upposition