Converting from 2D into 3D
-
Upload
elcoco1967 -
Category
Education
-
view
746 -
download
4
description
Transcript of Converting from 2D into 3D
![Page 1: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/1.jpg)
PRESENT:LEARNING TO CONVERT FROM 2D TO 3D
USING SolidWorks®
LEVEL: MEDIUM
![Page 2: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/2.jpg)
HOUSING2D TO 3D
THIS WILL BE THE FINAL MODEL
![Page 3: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/3.jpg)
AutoCAD 2D Drawing
We select all lines (we can apply AutoCAD filter
option) and CTRL-C
![Page 4: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/4.jpg)
In SolidWorks, we use Ctrl-V (Paste) and create blocks
Block1-1Block3-1
Block4-1 Block2-1
(4) Four block created in SW (Front, side, section A-A and section B-B)
![Page 5: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/5.jpg)
Insert Block3-1 on “Front Plane”
Insert Block4-1 on “Right Plane”
![Page 6: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/6.jpg)
Sketch using “convert entities” option Extrudes the sketch as
shown
![Page 7: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/7.jpg)
Sketch using “convert entities” option
Cut-Extrudes the sketch as shown
![Page 8: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/8.jpg)
Use same technique:• Sketch using “convert
entities” option• Extrude or Cut-Extrude
![Page 9: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/9.jpg)
Mirror for flange Cut-ExtrudeCut-Extrude
Internal Cut-Extrude
![Page 10: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/10.jpg)
Working on the internal cavity
![Page 11: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/11.jpg)
Mainly, we use hole wizard positioning the holes based on the block-sketch
![Page 12: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/12.jpg)
Creating oil feed
Finishing the base
![Page 13: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/13.jpg)
Adding fillets
To finish the internal cavity, use same technique:• Sketch using “convert
entities” option• Extrude or Cut-Extrude
Cut-Extrude
![Page 14: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/14.jpg)
Creating the extension for bottom bolts (4 places)
Create the sketch in the middle plane using “convert entities” option.
Extrude as shown
For the another side we have three options:-Mirror features or-Array features or-Extrude the sketch and you will see the “sketch37” with a hand, this means, the sketch is shared.
This is a shared sketch
We use this option
![Page 15: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/15.jpg)
Finally, we have a 3D detailed model.
![Page 16: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/16.jpg)
3D MODEL 3D RENDERED MODEL
![Page 17: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/17.jpg)
![Page 18: Converting from 2D into 3D](https://reader035.fdocuments.in/reader035/viewer/2022062307/55618d2dd8b42a96778b4edb/html5/thumbnails/18.jpg)
Conclusion.
• Convert from 2D into 3D is easy as per we saw in this presentation only if your 2D source drawing is done correctly.
• It is not necessary convert everything. You take your models that you really need to convert.
• If you need to insert a model in an assembly to check dimensions, position, interference, etc., then it is not necessary to create a detailed model.
• You can apply this procedure using others 3D softwares.
If you need more detailed information, please contact us: [email protected]