ControlLogix Compute Modules - RockwellAutomation.com · 2020. 4. 21. · The Compute module offers...

Installation Instructions

Original Instructions

ControlLogix Compute ModulesCatalog Numbers 1756-CMS1B1, 1756-CMS1B4, 1756-CMS1C1

ControlLogix® Compute modules lets you communicate directly to a ControlLogix 5570 or ControlLogix 5580 controller via the system backplane.

The Compute modules offer an operating system within which, you can create custom applications. Compute modules offer a Windows 10 IoT Enterprise operating system (OS) or a Linux OS.

• 1756-CMS1B1 module - Windows 10 IoT Enterprise 64-bit OS• 1756-CMS1B4 - FactoryTalk analytics software• 1756-CMS1C1 module - Linux OS 32-bit

The Compute module offers the following:

• Two GbE ports• One USB 3.0 device port for OS peripheral connections• An integrated DisplayPort for high definition monitor connectivity

You use an application programming interface (API) on the OS to create the custom applications.

Topic Page

Required System Components 5

Product Dimensions 5

Module Overview 6

Remove the Battery Paper Tab 6

Install the Module 7

Connect to the Module 7

Power the Module 8

Replacement Battery 9

Rotary Switches 10

Reset Button 10

Specifications 11

Additional Resources 11

ControlLogix Compute Modules

ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration and operation of this equipment before you install, configure, operate or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of practice.If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.注意：在安装、配置、操作和维护本产品前，请阅读本文档以及 “其他资源”部分列出的有关设备安装、配置和操作的相应文档。除了所有适用规范、法律和标准的相关要求之外，用户还必须熟悉安装和接线说明。

安装、调整、投运、使用、组装、拆卸和维护等各项操作必须由经过适当训练的专业人员按照适用的操作规范实施。

如果未按照制造商指定的方式使用该设备，则可能会损害设备提供的保护。ATENCIÓN: Antes de instalar, configurar, poner en funcionamiento o realizar el mantenimiento de este producto, lea este documento y los documentos listados en la sección Recursos adicionales acerca de la instalación, configuración y operación de este equipo. Los usuarios deben familiarizarse con las instrucciones de instalación y cableado y con los requisitos de todos los códigos, leyes y estándares vigentes.El personal debidamente capacitado debe realizar las actividades relacionadas a la instalación, ajustes, puesta en servicio, uso, ensamblaje, desensamblaje y mantenimiento de conformidad con el código de práctica aplicable.Si este equipo se usa de una manera no especificada por el fabricante, la protección provista por el equipo puede resultar afectada.ATENÇÃO: Leia este e os demais documentos sobre instalação, configuração e operação do equipamento que estão na seção Recursos adicionais antes de instalar, configurar, operar ou manter este produto. Os usuários devem se familiarizar com as instruções de instalação e fiação além das especificações para todos os códigos, leis e normas aplicáveis.É necessário que as atividades, incluindo instalação, ajustes, colocação em serviço, utilização, montagem, desmontagem e manutenção sejam realizadas por pessoal qualificado e especializado, de acordo com o código de prática aplicável. Caso este equipamento seja utilizado de maneira não estabelecida pelo fabricante, a proteção fornecida pelo equipamento pode ficar prejudicada.ВНИМАНИЕ: Перед тем как устанавливать, настраивать, эксплуатировать или обслуживать данное оборудование, прочитайте этот документ и документы, перечисленные в разделе «Дополнительные ресурсы». В этих документах изложены сведения об установке, настройке и эксплуатации данного оборудования. Пользователи обязаны ознакомиться с инструкциями по установке и прокладке соединений, а также с требованиями всех применимых норм, законов и стандартов.Все действия, включая установку, наладку, ввод в эксплуатацию, использование, сборку, разборку и техническое обслуживание, должны выполняться обученным персоналом в соответствии с применимыми нормами и правилами.Если оборудование используется не предусмотренным производителем образом, защита оборудования может быть нарушена.注意 : 本製品を設置、構成、稼動または保守する前に、本書および本機器の設置、設定、操作についての参考資料の該当箇所に記載されている文書に目を通してください。ユーザは、すべての該当する条例、法律、規格の要件に加えて、設置および配線の手順に習熟している必要があります。

設置調整、運転の開始、使用、組立て、解体、保守を含む諸作業は、該当する実施規則に従って訓練を受けた適切な作業員が実行する必要があります。

本機器が製造メーカにより指定されていない方法で使用されている場合、機器により提供されている保護が損なわれる恐れがあります。ACHTUNG: Lesen Sie dieses Dokument und die im Abschnitt „Weitere Informationen“aufgeführten Dokumente, die Informationen zu Installation, Konfiguration und Bedienung dieses Produkts enthalten, bevor Sie dieses Produkt installieren, konfigurieren, bedienen oder warten. Anwender müssen sich neben den Bestimmungen aller anwendbaren Vorschriften, Gesetze und Normen zusätzlich mit den Installations- und Verdrahtungsanweisungen vertraut machen.Arbeiten im Rahmen der Installation, Anpassung, Inbetriebnahme, Verwendung, Montage, Demontage oder Instandhaltung dürfen nur durch ausreichend geschulte Mitarbeiter und in Übereinstimmung mit den anwendbaren Ausführungsvorschriften vorgenommen werden.Wenn das Gerät in einer Weise verwendet wird, die vom Hersteller nicht vorgesehen ist, kann die Schutzfunktion beeinträchtigt sein.ATTENTION : Lisez ce document et les documents listés dans la section Ressources complémentaires relatifs à l’installation, la configuration et le fonctionnement de cet équipement avant d’installer, configurer, utiliser ou entretenir ce produit. Les utilisateurs doivent se familiariser avec les instructions d’installation et de câblage en plus des exigences relatives aux codes, lois et normes en vigueur.Les activités relatives à l’installation, le réglage, la mise en service, l’utilisation, l’assemblage, le démontage et l’entretien doivent être réalisées par des personnes formées selon le code de pratique en vigueur.Si cet équipement est utilisé d’une façon qui n’a pas été définie par le fabricant, la protection fournie par l’équipement peut être compromise.주의 : 본 제품 설치 , 설정 , 작동 또는 유지 보수하기 전에 본 문서를 포함하여 설치 , 설정 및 작동에 관한 참고 자료 섹션의 문서들을 반드시 읽고 숙지하십시오 . 사용자는 모든 관련 규정 , 법규 및 표준에서 요구하는 사항에 대해 반드시 설치 및 배선 지침을 숙지해야 합니다 .

설치 , 조정 , 가동 , 사용 , 조립 , 분해 , 유지보수 등 모든 작업은 관련 규정에 따라 적절한 교육을 받은 사용자를 통해서만 수행해야 합니다 .

본 장비를 제조사가 명시하지 않은 방법으로 사용하면 장비의 보호 기능이 손상될 수 있습니다 .ATTENZIONE Prima di installare, configurare ed utilizzare il prodotto, o effettuare interventi di manutenzione su di esso, leggere il presente documento ed i documenti elencati nella sezione “Altre risorse”, riguardanti l’installazione, la configurazione ed il funzionamento dell’apparecchiatura. Gli utenti devono leggere e comprendere le istruzioni di installazione e cablaggio, oltre ai requisiti previsti dalle leggi, codici e standard applicabili.Le attività come installazione, regolazioni, utilizzo, assemblaggio, disassemblaggio e manutenzione devono essere svolte da personale adeguatamente addestrato, nel rispetto delle procedure previste.Qualora l’apparecchio venga utilizzato con modalità diverse da quanto previsto dal produttore, la sua funzione di protezione potrebbe venire compromessa.DİKKAT: Bu ürünün kurulumu, yapılandırılması, işletilmesi veya bakımı öncesinde bu dokümanı ve bu ekipmanın kurulumu, yapılandırılması ve işletimi ile ilgili İlave Kaynaklar bölümünde yer listelenmiş dokümanları okuyun. Kullanıcılar yürürlükteki tüm yönetmelikler, yasalar ve standartların gereksinimlerine ek olarak kurulum ve kablolama talimatlarını da öğrenmek zorundadır.Kurulum, ayarlama, hizmete alma, kullanma, parçaları birleştirme, parçaları sökme ve bakım gibi aktiviteler sadece uygun eğitimleri almış kişiler tarafından yürürlükteki uygulama yönetmeliklerine uygun şekilde yapılabilir.Bu ekipman üretici tarafından belirlenmiş amacın dışında kullanılırsa, ekipman tarafından sağlanan koruma bozulabilir.注意事項：在安裝、設定、操作或維護本產品前，請先閱讀此文件以及列於「其他資源」章節中有關安裝、設定與操作此設備的文件。使用者必須熟悉安裝和配線指示，並符合所有法規、法律和標準要求。

包括安裝、調整、交付使用、使用、組裝、拆卸和維護等動作都必須交由已經過適當訓練的人員進行，以符合適用的實作法規。

如果將設備用於非製造商指定的用途時，可能會造成設備所提供的保護功能受損。POZOR: Než začnete instalovat, konfigurovat či provozovat tento výrobek nebo provádět jeho údržbu, přečtěte si tento dokument a dokumenty uvedené v části Dodatečné zdroje ohledně instalace, konfigurace a provozu tohoto zařízení. Uživatelé se musejí vedle požadavků všech relevantních vyhlášek, zákonů a norem nutně seznámit také s pokyny pro instalaci a elektrické zapojení.Činnosti zahrnující instalaci, nastavení, uvedení do provozu, užívání, montáž, demontáž a údržbu musí vykonávat vhodně proškolený personál v souladu s příslušnými prováděcími předpisy.Pokud se toto zařízení používá způsobem neodpovídajícím specifikaci výrobce, může být narušena ochrana, kterou toto zařízení poskytuje.UWAGA: Przed instalacją, konfiguracją, użytkowaniem lub konserwacją tego produktu należy przeczytać niniejszy dokument oraz wszystkie dokumenty wymienione w sekcji Dodatkowe źródła omawiające instalację, konfigurację i procedury użytkowania tego urządzenia. Użytkownicy mają obowiązek zapoznać się z instrukcjami dotyczącymi instalacji oraz oprzewodowania, jak również z obowiązującymi kodeksami, prawem i normami.Działania obejmujące instalację, regulację, przekazanie do użytkowania, użytkowanie, montaż, demontaż oraz konserwację muszą być wykonywane przez odpowiednio przeszkolony personel zgodnie z obowiązującym kodeksem postępowania.Jeśli urządzenie jest użytkowane w sposób inny niż określony przez producenta, zabezpieczenie zapewniane przez urządzenie może zostać ograniczone.OBS! Läs detta dokument samt dokumentet, som står listat i avsnittet Övriga resurser, om installation, konfigurering och drift av denna utrustning innan du installerar, konfigurerar eller börjar använda eller utföra underhållsarbete på produkten. Användare måste bekanta sig med instruktioner för installation och kabeldragning, förutom krav enligt gällande koder, lagar och standarder.Åtgärder som installation, justering, service, användning, montering, demontering och underhållsarbete måste utföras av personal med lämplig utbildning enligt lämpligt bruk.Om denna utrustning används på ett sätt som inte anges av tillverkaren kan det hända att utrustningens skyddsanordningar försätts ur funktion.LET OP: Lees dit document en de documenten die genoemd worden in de paragraaf Aanvullende informatie over de installatie, configuratie en bediening van deze apparatuur voordat u dit product installeert, configureert, bediend of onderhoudt. Gebruikers moeten zich vertrouwd maken met de installatie en de bedradingsinstructies, naast de vereisten van alle toepasselijke regels, wetten en normen.Activiteiten zoals het installeren, afstellen, in gebruik stellen, gebruiken, monteren, demonteren en het uitvoeren van onderhoud mogen uitsluitend worden uitgevoerd door hiervoor opgeleid personeel en in overeenstemming met de geldende praktijkregels.Indien de apparatuur wordt gebruikt op een wijze die niet is gespecificeerd door de fabrikant, dan bestaat het gevaar dat de beveiliging van de apparatuur niet goed werkt.

2 Rockwell Automation Publication 1756-IN072B-EN-P - March 2019


Environment and Enclosure

ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in EN/IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is not intended for use in residential environments and may not provide adequate protection to radio communication services in such environments.

This equipment is supplied as open-type equipment for indoor use. It must be mounted within an enclosure that is suitably designed for those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts. The enclosure must have suitable flame-retardant properties to prevent or minimize the spread of flame, complying with a flame spread rating of 5VA or be approved for the application if nonmetallic. The interior of the enclosure must be accessible only by the use of a tool. Subsequent sections of this publication may contain more information regarding specific enclosure type ratings that are required to comply with certain product safety certifications.

In addition to this publication, see the following:

• Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1, for more installation requirements.• NEMA 250 and EN/IEC 60529, as applicable, for explanations of the degrees of protection provided by enclosures.

North American Hazardous Location Approval

The following information applies when operating this equipment in hazardous locations. Informations sur l’utilisation de cet équipement en environnements dangereux.

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous locations only. Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code. When combining products within a system, the most adverse temperature code (lowest "T" number) may be used to help determine the overall temperature code of the system. Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne conviennent qu'à une utilisation en environnements de Classe I Division 2 Groupes A, B, C, D dangereux et non dangereux. Chaque produit est livré avec des marquages sur sa plaque d'identification qui indiquent le code de température pour les environnements dangereux. Lorsque plusieurs produits sont combinés dans un système, le code de température le plus défavorable (code de température le plus faible) peut être utilisé pour déterminer le code de température global du système. Les combinaisons d'équipements dans le système sont sujettes à inspection par les autorités locales qualifiées au moment de l'installation.

WARNING:Explosion Hazard –• Do not disconnect equipment unless power has been removed or the

area is known to be nonhazardous. • Do not disconnect connections to this equipment unless power has

been removed or the area is known to be nonhazardous. Secure any external connections that mate to this equipment by using screws, sliding latches, threaded connectors, or other means provided with this product.

• Substitution of components may impair suitability for Class I, Division 2.• If this product contains batteries, they must only be changed in an area

known to be nonhazardous.

AVERTISSEMENT:Risque d’Explosion – • Couper le courant ou s'assurer que l'environnement est classé non

dangereux avant de débrancher l'équipement.• Couper le courant ou s'assurer que l'environnement est classé non

dangereux avant de débrancher les connecteurs. Fixer tous les connecteurs externes reliés à cet équipement à l'aide de vis, loquets coulissants, connecteurs filetés ou autres moyens fournis avec ce produit.

• La substitution de composants peut rendre cet équipement inadapté à une utilisation en environnement de Classe I, Division 2.

• S'assurer que l'environnement est classé non dangereux avant de changer les piles.

Rockwell Automation Publication 1756-IN072AB-EN-P - March 2019 3

http://literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdf


Prevent Electrostatic Discharge

ATTENTION: This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when you handle this equipment:

• Touch a grounded object to discharge potential static.• Wear an approved grounding wriststrap.• Do not touch connectors or pins on component boards.• Do not touch circuit components inside the equipment.• Use a static-safe workstation, if available.• Store the equipment in appropriate static-safe packaging when not in use.

ATTENTION:

• Installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of practice.In case of malfunction or damage, no attempts at repair should be made. The controller should be returned to the manufacturer for repair. Do not dismantle the controller.

• When installed in a 1756 Series C Chassis, this equipment is certified for use only within the surrounding air temperature range of -25…60 °C (32…140 °F). The equipment must not be used outside of this range. When installed in a 1756 Series B Chassis, this equipment is certified for use only within the surrounding air temperature range of -25…50 °C (32…122 °F). The equipment must not be used outside of this range.

• Use only a soft dry anti-static cloth to wipe down equipment. Do not use any cleaning agents.• USB and DisplayPort cables are not to exceed 3.0 m (9.84 ft).

Waste Electrical and Electronic Equipment (WEEE)

Pb/Cd/Hc

At the end of its life, this equipment should be collected separately from any unsorted municipal waste.

IMPORTANT: This product contains a Type BR1225A Lithium battery which may need to be replaced during the life of the product. For instructions on the removal and replacement of the battery, refer to page 9.

At the end of its life, the battery contained in this product should be collected separately from any unsorted municipal waste. The collection and recycling of batteries helps protect the environment and contributes to the conservation of natural resources as valuable materials are recovered.

IMPORTANTAny illustrations, charts, sample programs, and layout examples that are shown in this publication are intended solely for the purposes of example. Since there are many variables and requirements that are associated with any particular installation, Rockwell Automation does not assume responsibility or liability for actual use that is based upon the examples that are shown in this publication.

4 Rockwell Automation Publication 1756-IN072AB-EN-P - March 2019


Required System ComponentsTo use the Compute module, you need a ControlLogix 5570 or 5580 system that includes a controller.

You can use the Compute module in the following ways:

• In the same chassis as the ControlLogix controller with which it is communicating.

• In a remote chassis that is connected via an EtherNet/IP network to the chassis in which the controller resides.

• In a remote chassis that is connected to a ControlLogix Enhanced Redundancy system via an EtherNet/IP network.

For more information on how to use a Compute module in different locations, see the ControlLogix Compute Module User Manual, publication 1756-UM003.

Product Dimensions

IMPORTANT ControlLogix Compute modules cannot reside in the redundant pair, that is, neither the primary nor secondary chassis in an enhanced redundancy system.

145.20 mm (5.72 in.)

34.55 mm (1.36 in.)139.60 mm (5.50 in.)


http://literature.rockwellautomation.com/idc/groups/literature/documents/um/1756-um003_-en-p.pdf


Module Overview Remove the Battery Paper TabCompute modules use a battery to maintain the real-time clock on the module when there is no power applied to module. A battery is installed in the module when it ships.

A red paper tab covers the side of the battery that faces the backplane when the module is installed in a chassis.

You must remove the paper tab before you install the module. To remove the paper tab, pull it off.

ControlLogix Compute Module Components

Number Item Description

1 Four-character display Scrolls information about the module

2 Status indicators User programmable

3 Reset button Used after module operation begins.Behind the module door.

4 DisplayPort connection Connector to use a display with the OS on the module.Behind the module door.

5 USB 3.0 port Connect peripherals to be used with the OS

6 Ethernet ports 1 and 2Used after module operation begins.• Port 1 is the bottom port.• Port 2 is the top port.

1

2

5

6

IMPORTANT: Some modules have only 1 Ethernet port.

3

4

Battery Paper Tab



Install the ModuleYou can install the module in any open slot in a ControlLogix chassis regardless of whether the module is in the local chassis or a remote chassis with respect to the controller location.

1. Align the circuit board with the top and bottom guides in the chassis.

2. Slide the modules into the chassis until it snaps into place.

3. Verify that the module is flush with the other installed modules.

Connect to the ModuleYou can connect to the Compute module in the following ways:

• DisplayPort• USB 3.0 port• Ethernet ports

This section describes how to connect to each port type. It does not provide details of how to use the ports.

For more information on how to use these connection types, see the ControlLogix Compute Module User Manual, publication 1756-UM003.

Connect to the DisplayPort

The DisplayPort interface lets you connect industrial monitors to the Compute module to use with the OS. You can use the following industrial monitors with your Compute module:

• Super Video Graphics Array (SVGA) to HD 1080p• High-Definition Multimedia Interface (HDMI)• Video Graphics Array (VGA)• Digital Visual Interface (DVI)• DisplayPort

You must use a VESA-certified DisplayPort adapter to connect some industrial monitors to the module.

Connect a Cable to the DisplayPort

WARNING: When you insert or remove the module while backplane power is on, an electric arc can occur. This could cause an explosion in hazardous location installations.

Be sure that power is removed or the area is nonhazardous before proceeding. Repeated electric arcing causes excessive wear to contacts on both the module and its mating connector. Worn contacts may create electrical resistance that can affect module operation.

WARNING: If you connect or disconnect the DisplayPort cable with power applied to this module or any connected display devices, an electric arc can occur. This could cause an explosion in hazardous location installations.

Be sure that power is removed or the area is nonhazardous before proceeding.

TIP We recommend that you connect a monitor to the DisplayPort before you power up the module.




Connect to the USB Port

You use the USB port to connect peripherals, for example, a wireless keyboard, to the module.

Figure 1 - Connect to the USB Port

Connect to an Ethernet Port

You use Ethernet ports to connect the module to EtherNet/IP networks.

To connect the module to an EtherNet/IP network, connect an RJ45 cable to an embedded Ethernet port.

Connect an Ethernet Cable to the Compute Module

Power the ModuleAfter you install the module and make the necessary connections to it, you can turn on power to the system.

The module performs a power-up sequence. As part of the power-up sequence, you must log in to the OS. The first time that you power up the module, you must complete the standard Windows tasks, such as reading and accepting the Microsoft Windows EULA.

The 4-character display and status indicators on the module indicate when the power-up sequence is complete.

For more information on how to use the 4-character display and status indicators and how to log in to the OS, see the ControlLogix Compute Module User Manual, publication 1756-UM003.

WARNING: If you connect or disconnect the USB cable with power applied to this module or any device on the USB network, an electric arc can occur. This could cause an explosion in hazardous location installations.


TIP We recommend the following:

• Connect peripherals to the USB port before you power up the module.

• Use wireless peripherals with the USB port to reduce the number of cables that are connected to the module.

USB Cable Connection

USB Dongle Connection

WARNING: If you connect or disconnect an Ethernet cable with power applied to this module or any device on the network, an electric arc can occur. This could cause an explosion in hazardous location installations.





Replacement BatteryCompute modules use a battery to maintain the real-time clock on the module when there is no power applied to module. A battery is installed in the module when it ships.

You can replace the battery if necessary. The battery is a Panasonic Type BR1225A coin type lithium battery. Replacement batteries are commercially available.

To replace the battery, complete these steps.

1. Pull the white plastic battery holder from the back of the module.

If necessary, pull the holder out far enough to use a small screwdriver to pry out the battery. In this case, insert the screwdriver from the side of the battery that faces the module printed circuit board.

2. Remove the old battery from the holder.

3. Install a new battery into the holder.

The side of the battery with words and numbers is installed in the side of the holder with tabs to hold it in place.

4. Reinstall the battery holder in the back of the module.

The narrower part of the holder is installed first into the metal guides.

5. Push the battery holder all the way into the back of the module.

WARNING: When you connect or disconnect the battery an electric arc can occur. This could cause an explosion in hazardous location installations. Be sure that the area is nonhazardous before proceeding.

For Safety information on the handling of lithium batteries, including handling and disposal of leaking batteries, see Guidelines for Handling Lithium Batteries, publication AG 5-4.

IMPORTANT There are metal guides that hold the battery holder in place. Do not attempt to remove the metal guides.

BR1225A

3V

IMPORTANT Make sure that the battery is installed in an orientation so that the side of the battery with words and numbers faces away from the PCB.

BR12

25A

3V

Battery Holder Tabs

BR1225A

3V


http://literature.rockwellautomation.com/idc/groups/literature/documents/td/ag-td054_-en-p.pdf


Rotary Switches

Compute modules have rotary switches on the side of the module.

Figure 2 - ControlLogix Compute Module Rotary Switches

You use the switches after module operation begins.

For more information on how to use the rotary switches after operation has begun, see the ControlLogix Compute Module User Manual, publication 1756-UM003.

Reset ButtonCompute modules have a reset button behind the door that functions like the power button on a computer and only works with the OS. For example, if you press and release the button, an orderly shutdown occurs on the OS.

The button is not used during module installation.

For more information on how to use the reset button after module operation has begun, see the ControlLogix Compute Module User Manual, publication 1756-UM003.

Status IndicatorsThe module has four programmable status indicators.

You can program the following states.

For information on how to program the status indicators, see ControlLogix Compute Modules User Manual, publication 1756-UM003.

WARNING: When you change switch settings while power is on, an electric arc can occur. This could cause an explosion in hazardous location installations.


Rotary Switches

WARNING: When you press the reset button while power is on, an electric arc can occur. This could cause an explosion in hazardous location installations.


State Description

Off The module is not powered.

Solid Green The module operating normally.

Solid Red One of the following:• A major communication fault has occurred

between the module and ControlLogix chassis backplane. You must troubleshoot your application to determine the cause of the solid red condition on indicator OK.

• A module shutdown is complete.

Programmable status indicators


http://literature.rockwellautomation.com/idc/groups/literature/documents/um/1756-um003_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/1756-um003_-en-p.pdfhttps://literature.rockwellautomation.com/idc/groups/literature/documents/um/1756-um003_-en-p.pdf


Specifications

Additional ResourcesThese documents contain additional information concerning related products from Rockwell Automation.

You can view or download publications at http://www.rockwellautomation.com/global/literature-library/overview.page. To order paper copies of technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative.

Attribute 1756-CMS1B1, 1756-CMS1B4, 1756-CMS1C1

Temperature, operatingIEC 60068-2-1 (Test Ad, Operating Cold),IEC 60068-2-2 (Test Bd, Operating Dry Heat),IEC 60068-2-14 (Test Nb, Operating Thermal Shock)

Series C Chassis: -25 °C < Ta < +60 °C (-13 °F < Ta < +140 °F)Series B Chassis: -25 °C < Ta < +50 °C (-13 °F < Ta < +122 °F)

Temperature, Surrounding Air, max Series C Chassis: 60 °C (140 °F)Series B Chassis: 50 °C (122 °F)

Enclosure type rating None (open-style)

Voltage and current ratings 5.1 V DC @ 1.40 A

Wire size Ethernet cabling and installation according to IEC 61918 and IEC 61784-5-2

North American Temp Code T5

Resource Description

ControlLogix Compute Module User Manual, publication 1756-UM003. Describes how to use the ControlLogix Compute module.

ControlLogix Compute Module Specifications Technical Data, publication 1756-TD007 Provides specifications for the ControlLogix Compute module.

Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 Provides general guidelines for installing a Rockwell Automation® industrial system.

Product Certifications website,http://www.rockwellautomation.com/global/certification/overview.page Provides declarations of conformity, certificates, and other certification details.


http://literature.rockwellautomation.com/idc/groups/literature/documents/um/1756-um003_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/td/1756-td001_-en-p.pdfhttp://www.rockwellautomation.com/global/literature-library/overview.pagehttp://literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdfhttp://www.rockwellautomation.com/global/certification/overview.page

Rockwell Automation SupportUse the following resources to access support information.

Documentation FeedbackYour comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document, complete the How Are We Doing? form at http://literature.rockwellautomation.com/idc/groups/literature/documents/du/ra-du002_-en-e.pdf.

Technical Support Center Knowledgebase Articles, How-to Videos, FAQs, Chat, User Forums, and Product Notification Updates. https://rockwellautomation.custhelp.com/

Local Technical Support Phone Numbers Locate the phone number for your country. http://www.rockwellautomation.com/global/support/get-support-now.page

Direct Dial Codes Find the Direct Dial Code for your product. Use the code to route your call directly to a technical support engineer. http://www.rockwellautomation.com/global/support/direct-dial.page

Literature Library Installation Instructions, Manuals, Brochures, and Technical Data. http://www.rockwellautomation.com/global/literature-library/overview.page

Product Compatibility and Download Center (PCDC)

Get help determining how products interact, check features and capabilities, and find associated firmware. http://www.rockwellautomation.com/global/support/pcdc.page

Allen-Bradley, ControlLogix, Rockwell Automation, and Rockwell Software are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400

Rockwell Automation maintains current product environmental information on its website athttp://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

Publication 1756-IN072B-EN-P - March 2019 PN-540311Suopersedes 1756-IN027A-EN-P - November 2017 Copyright © 2019 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.

http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page

ControlLogix Compute Modules Installation Instructions, 1756-IN072B-EN-PRequired System ComponentsProduct DimensionsModule OverviewRemove the Battery Paper TabInstall the ModuleConnect to the ModuleConnect to the DisplayPortConnect to the USB PortConnect to an Ethernet Port

Power the ModuleReplacement BatteryRotary SwitchesReset ButtonStatus IndicatorsSpecificationsAdditional ResourcesBack Cover

Print Spec Sheet

RA-QR005K-EN-PJan-19

Printing SpecificationYOUR DATA HEREInstructionsNO

(required) Publication Number:1756-IN072B-EN-PSample: 2030-SP001B-EN-P11” x 17”LOOSE -Loose LeafYESPre-sale / MarketingTOP

Use Legacy Number:YES or NO8.5” x 11”PERFECT - Perfect BoundA1LEFT

Legacy Number if applicable:Sample Legacy Number: 0160-5.338.375” x 10.875SADDLE - Saddle StitchA2RIGHTCORNER

Publication Title:ControlLogix Compute Modules Installation InstructionsSample: ElectroGuard Selling Brief80 character limit - must match DocMan Title8.25” x 11” (RA product profile std)PLASTCOIL - Plastic Coil (Coil Bound)A4BOTTOMSIDE

Used in Manufacturing:YESYES or NO - If Yes, must have Part No. listed below8.25” x 10.875”STAPLED1 -1 positionA3

Part Number:PN-540311If SAP Part Number, be sure to enter PN- before the number7.385” x 9” (RSI Std)STAPLED1B - bottom 1 positionA5

(required) CategoryD5Select Print Category A,B,C or D from category list, on "Introduction_Category Types" tab6” x 4”STAPLED2 - 2 positionsA6

Paper Stock Color:White is assumed. For color options contact your vendor5.5” x 8.5” (half-size)THERMAL - Thermal bound (Tape bound)A7

Ink Color:One color assumes BLACK / 4 color assume CMYK / Indicate PMS number here4.75” x 7.75”THERMALO - Thermal Bound (Tape bound - offline)A8

(required) Page Count ofPublication:12Total page count including cover. Enter PAGE count, not SHEET count4.75” x 7” (slightly smaller half-size)A9

(required) Finished Trim Size Width:8.5” x 11”This is sheet size, before folding4.25" x 5.50"Post Sale / Technical Communication

Fold:Half or V or Single FoldReview key below. Leave blank if folded for saddle stitching4” x 6”B1

Finished Fold Size:5.5" x 8.5"This is size after folding is completed3” x 5”B2

Binding/Stitching:STAPLED1 -1 positionReview key below9” x 12” (Folder)B3None

Stitching Location:CORNERBlank, Corner or SideA4 (8 ¼” x 11 ¾”) (210 x 297 mm)B4Half or V or Single Fold

Drill Hole (Yes/No):NOAll drilled publications use the 5-hole standard, 5/16 inch-size hole and a minimum of ¼ inch from the inner page border.A5 (5.83” x 8.26”) (148 x 210 mm)B5C or Tri-Fold

Number of Tabs Needed:5 tab in stock at RR Donnelley36” x 24” PosterCatalogsDbleParll

Number of Pages per Pad:Average sheets of paper. 25, 50 75,100 Max24” x 36” PosterC1Sample

Glue Location on Pad:Glue location on pads18” x 24” PosterC2Short (must specify dimensions between folds in Comments)

Comments:Print on Demand (POD)Double Gate

Saddle-Stitch Items All page quantities must be divisible by 4.Note: Stitching is implied for Saddle-Stitch -no need to specify in Stitching Location.80 pgs max. on 20# (text and cover)76 pgs max. on 20# (text) and 24# (cover)72 pgs max. on 24# (text and cover)

Perfect Bound Items940 pgs max. w/cover (90# index unless indicated otherwise)70 pgs. min. for spine without words200 pgs min. for spine with words

Plastic Coil Bound Items530 pgs max. of 20# (if adding cover deduct equivalent number of pages to equal cover thickness) (90# index unless indicated otherwise)

Tape Bound Items250 pgs max. on 20# no cover240 pgs max. w/cover (90# index unless indicated otherwise)D1

D2

D5

D6

&LPrint Specifications

&LRockwell Automation Publication RA-QR005K-EN-P&RJanuary 2019

Introduction_Category Types

This tab summarizes Rockwell Automation Global Sales and Marketing preferred printing standards. It also provides guidance on whether a publication should be released print on demand or if it requires an RFQ for offset printing.Find your publication type in the first section below. Use the assigned Printing Category information to determine the standard print specifications for that document type. The Printing Categories are defined below the Publication Type section. Note there may be slightly different print specifications for the categories, depending on the region (EMEA or Americas).For more information on Global Sales and Marketing Printing Standards, see publication RA-CO004 in DocMan.

Publication Type and Print Category

Publication TypeOff Set Print Category Spec. (See tables below)Print on Demand Spec. (See tables below)DescriptionOrder Min **Order Max **Life Cycle Usage / Release Option

ADNA - PuttmanNAAdvertisement Reprint ColourNANAPresale / Internal

APA3D2Application Solution or Customer Success Story5100Presale / External

ARNANAArticle/Editorial/BylineNANAPresale / Internal

(press releases should not be checked into DocMan or printed)

ATB3, B4D5Application techniques5100Presale / External

BRA2 Primary, A1NABrochures5100Presale / External

CAC2 Primary, C1NACatalogue150Presale / External

CGNANACatalogue Guide150Presale / External

CLNANACollection550Presale / External

COA5, A6, A9D5Company Confidential InformationNANANA / Confidential

CPE-onlyE-only, D5Competitive Information550NA / Confidential

DCE-onlyE-onlyDiscount SchedulesNANAPresale / Internal

DIA1, A3NADirect Mail5100Presale / Internal

DMNANAProduct Demo550Presale / Internal

DSB3D5Dimensions Sheet15Post / External

DUB3D5Document Update15Post / External

GRB2D6Getting Results15Post / External

INB3 Primary, B2D5, D6Installation instructions15Post / External

LMNANALaunch Materials550Presale / Internal

PCB3D5Packaging Contents

PLE-only primary, B3E-onlyPrice List550Presale / Internal

PMB2D6Programming Manual15Post / External

PPA3D1Profile (Single Product or Service). NOTE: Application Solutions are to be assigned the AP pub type.5100Presale / External

QRB2 primary, B3, B5D5, D6Quick Reference15Post / External

QSB2 primary, B3, B5D5, D6Quick Start15Post / External

RMB2D5, D6Reference Manual15Post / External

RNB3D5Release Notes15Post / External

SGB1 Primary, B4D5, D6Selection Guide Colour550Presale / External

SGB2D5, D6Selection Guide B/W550Presale / External

SPA1, A2, A3, A4NASales Promotion NOTE: Service profiles are to be assigned the PP pub type.5100Presale / Internal

SRB2, B3D5, D6Specification Rating Sheet5100Presale / External

TDB2 Primary B3, B4, B5D5, D6Technical Data550Presale / External

TGB2, B3D6Troubleshooting Guide15Post / External

UMB2 Primary, B4D6User Manual B/W15Post / External

WDB3D5Wiring Diagrams / Dwgs15Post / Internal

WPB3 Primary, B5D5White Paper550Presale / External

** Minimum order quantities on all POD items are based on the publication length. **

Publication lengthMinimum Order Quantity

77 or more pages1 (no shrink wrap required)

33 to 76 pages25

3 to 32 pages50

1 or 2 pages100

Pre-sale / Marketing

All paper in this category is White Brightness, 90% or better. Opacity 90% or better

CategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US Paper Requirements

A14 color170 gsm 2pp100# gloss cover, 100# gloss text

A24 color170 gsm , folded, 4pp100# gloss cover, 80# gloss text

A34 colorCover 170 gsm with Body 120 gsm, > 4pp80# gloss cover, 80# gloss text

A42 color170gsm Silk – 120gsm Silk80# gloss cover, 80# gloss text

A52 color170gsm Silk – 120gsm Silk80# gloss cover, 80# matt sheet text

A61 color170gsm Silk – 120gsm Silk80# gloss cover, 80# matt sheet text

A74 color cover2 color textSelection GuideCategory being deleted10 Point Cover C2S50# matte sheet text

A84 color coverCategory being deleted50# matte sheet text, self cover

2 color text

Selection Guide

A92 color100gsm bond50# matte sheet text, self cover

Selection Guide

Gray shading indicates Obsolete Print Catagories

Post Sale / Technical Communication


B14 color cover270gsm Gloss 100gsm bond10 Point Cover C2S

2 color text50# matte sheet text

B21 color160gsm Colortech & 100gsm Bond90# Cover50# matte sheet text

B31 color100gsm bond50# matte sheet text, self cover

B42 color160gsm Colortech & 100gsm Bond90# Cover50# matte sheet text

B52 color100gsm bond50# matte sheet text, self cover

Catalogs


C14 color cover270gsm Gloss 90gsm silk10 Point Cover C2S

4 color text45# Coated Sheet

C24 color cover270gsm Gloss 80gsm silk10 Point Cover C2S

2 color text32#-33# Coated Sheet

Print on Demand by Print Vendor (POD)

All paper in this category is White Brightness, 82% or better. Opacity 88% or better


D14 color170gsm white silk80# gloss cover, coated 2 sides

D24 color120gsm white silk80# gloss text, coated 2 sides, self cover

D34 colorCover 170gsm with Body 120gsm80# gloss cover, 80# gloss text coated 2 sides

D41 color160gsm tab90# index

D51 color80gsm bond20# bond, self cover

D61 colorCover 160gsm tab with Body 80gsm bond90# index, 20# bond

D72 color160gsm tab90# index

D82 color80gsm bond20# bond, self cover

D92 colorCover 160gsm tab with Body 80gsm bond90# index, 20# bond

D10Combination: 4 color cover, with 2 color bodyCover 160gsm with Body 80gsm90# index, 20# bond

Gray shading indicates Obsolete Print Catagories

Print on Demand By Print Vendor (POD) or Off Set (OS)?

Use these guidelines to determine if your publication should be print on demand by print vendor (POD) or if it would be more economical to print ffset/on a press (OS). OS print jobs require an RFQ (Request For Quote) in US. If your job fits into the “Either” category, an RFQ is recommended, but not required. In the US, RA Strategic Sourcing will discourage or reject RFQs for jobs that fall within the POD category. Guidelines differ for black & white and color printing, so be sure to check the correct tables.

&LPrint Specifications

&LRockwell Automation Publication RA-QR005K-EN-P&RJanuary 2019

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Average /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 2.00000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages false /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Average /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile (None) /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False

/CreateJDFFile false /Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure true /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles true /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /NA /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice

ControlLogix Compute Modules - RockwellAutomation.com · 2020. 4. 21. · The Compute module offers...

Documents

Transcript of ControlLogix Compute Modules - RockwellAutomation.com · 2020. 4. 21. · The Compute module offers...