Control-m v8 Installation on Windows 2008 Cluster

8/10/2019 Control-m v8 Installation on Windows 2008 Cluster

1/45

CONTROL -M V8INSTALLATION ON

WINDOWS 2008

CLUSTER Guide to install Control-M Enterprise Manager and Control-M Server V8 on

Windows 2008 Cluster


2/45

Control-M V8 installation on WIndows 2008 cluster

Page 1

Content Page

1. Pre-Installation Checklist

2. Creating Disk, IP Address and Network Name for Control-M Installation . 4

3. Control-M EM Installation on Primary Clustered Node

4. Setting up failover nodes for Control-M EM

5. Control-M Server Installation on Primary Clustered Node . 2

6. Setting up failover nodes for Control-M Server . 34

7. Setting up Control-M GTW on Control-M Configuration Manager (CCM) and Failover Cluster

Management GUI 38


3/45


Page 2

1. Pre-Installation ChecklistNote:

- One Install is not supported on Windows Cluster Environment:

- Install Microsoft .NET Framework 4 on both Windows 2008 Cluster Node.

If not, proceed to install using the binary provided.


4/45


Page 3


5/45


Page 4

2. Creating Disk, IP Address and Network Name for Control-M Installation

- Log on as Domain Administrator to start installation

- Ensure that the Current Host Server is the node that the installation is being performed.


6/45


Page 5

- Verification that the Disk, IP Address and Network Name are online and available.

- Create a New Service or Application for Control -MRight-click on Services and Applications > More Actions > Create Empty Service orApplication


7/45


Page 6

- When the new application is created, right click on the New service or Application Select Rename and give the Application a new name. (CTMV8)

- Add a New Resource

Right click on CTMV8 > Add a resource > 1 Client Access Point

- Give the Client Access Point, CTMV8, a new IP Address (192.168.134.90)


8/45


Page 7

- Click Next to complete the creation of the Client Access Point.

- Add a storageRight Click on CTMV8 > Add Storage


9/45


10/45


Page 9

- Bring the Server Name, Disk Drives and Network IP Address online.Right click on CTMV8 > Bring this service or application online


11/45


Page 10

3. Control-M EM Installation on Primary Clustered Node

- Start the Control-M EM Installation on the Primary Clustered Node as followed:


12/45


Page 11


13/45


Page 12

Note:

If the Cluster Group, Disk Resource and Network are configured correctly and online, theseinformation will appear as above automatically. If not, please repeat STEP (2) again.


14/45


Page 13


15/45


Page 14

PostgreSQL service password: Pa55word


16/45


Page 15

Database Owner Username: emuser

Database Owner Password: empass

Database Administrator Password: password


17/45


Page 16


18/45


Page 17

- Installation completed successfully and the Control-M Workload Automation GUI should bestarted as below.


19/45


Page 18

- Install the Control-M Batch Impact Manager


20/45


Page 19

- Install the Control-M Forecast


21/45


Page 20

- Control-M Enterprise Manager / Control-M Batch Impact Manager / Control-M Forecastshould be able to be start and made ONLINE using the Windows Cluster Management.


22/45


Page 21

4. Setting up failover nodes for Control-M EM

- Verify that the owner of the Control-M/EM cluster group is the primary node on which you installedthe full Control-M/EM installation. On each failover node, perform the following

- Bring the primary Disk, IP address, and Network Name cluster resources online.

- Ensure that the Control-M CORBA Naming service remains online.

- Perform a failover of the Control-M/EM group from the primary node to the secondary node.


23/45


Page 22

- Ensure that the Disk, IP address, and Network Name resources are online on the failover node.All resources except Control-M Naming Service for EM will be OFFLINE.

- Open a command prompt and run Setup_files\3RD\setup_em.bat from the installation DVD.

Note:

If you are using Windows 2008, you must run the command prompt as an administrator.


24/45


Page 23

- The following step applies only for a PostgreSQL installation.On a PostgreSQL installation, give Log On as a Services permissions to the local NT user that wascreated for PostgreSQL by performing the following steps:

- From the command line (Start > Run), run Services.msc

- Locate PostgreSQL for Control-M/EM version xxx and locate .\and save this name forlater.


25/45


26/45


Page 25

- Enter the object name to select, enter a name for the this account service.This name is the you saved in above.

- Bring up the Control-M EM Application online

- Right click on the Control- M Application then select Bring this ser vice or applicationonline.


27/45


Page 26

- Control-M EM Application can be move to another node as well.


28/45


Page 27

5. Control-M Server Installation on Primary Clustered Node

- Start the installation for Control-M Server

- Select Control -M Server under the Advanced Installations


29/45


Page 28


30/45


Page 29


31/45


Page 30

- Select the Database Server Installation(In this guide, Control-M Server will be using the existing BMC-supplied PostgreSQLDatabase Server)

- Perform a Test to ensure that the Host is available.


32/45


Page 31

Control-M Server Database Owner: ctmuser

Control-M Server Database Owner Password: ctmpass

Database Administrator Password: password


33/45


Page 32


34/45


Page 33


35/45


Page 34

6. Setting up failover nodes for Control-M Server

- Verify that the owner of the Control-M cluster group is the primary node on which you installed thefull Control-M installation. On each failover node, perform the following

- Bring the primary Disk, IP address, and Network Name cluster resources online.

- Ensure that the Control-M Server and Control-M Server Configuration service remains online.

- Perform a failover of the Control-M group from the primary node to the secondary node.


36/45


Page 35

- Ensure that the Disk, IP address, Network Name and Control-M Application resources are online onthe failover node.

- Open a command prompt and run Setup_files\3RD\setup_ctm.bat from the installation DVD.

Note:

If you are using Windows 2008, you must run the command prompt as an administrator.


37/45


Page 36

- If setup_ctm.bat did not start executing and display the following error, please do check that theControl-M Server and Control-M Server Configuration Agent application services is online on thesecondary nodes.

- Right click on the Control- M Application then select Bring this service or applicationonline.

- Also ensure that the Control-M Application cab be move to the Primary node.


38/45


Page 37


39/45


Page 38

7. Setting up Control-M GTW on Control-M Configuration Manager (CCM)and Failover Cluster Management GUI

- Discover Control-M Server and the its Gateway.


40/45


Page 39


41/45


42/45


Page 41

- Supply the information as followed:


43/45


Page 42

- Add the Control -M Naming Service for EM as a Dependency


44/45


Page 43


45/45


- Update the Pending timeout to 10 minutes.

- Control-M Server installation on Windows 2008 Cluster completed.

Control-m v8 Installation on Windows 2008 Cluster

Documents

Transcript of Control-m v8 Installation on Windows 2008 Cluster