Contents of DOWNLOAD · available as BEETLEview update packages, provided for older release LANDesk...

D2 motherboard BIOS update „WN STD 0E/26“

README.PDF 1 / 46

Contents of DOWNLOAD.ZIP .\DOS\??UPDATE????ARJ.EXE Self extracting archive of DOS based flash update disk for MS-

DOS. Needs a prepared bootable floppy or memory card .\DOS\??UPDATE????IMG.EXE Directly creates a bootable DOS based flash update disk on

1,44MB/3,5" floppy. To be created with Windows only . .\DOS\??UPDATE????DD.BIN Floppy image file of DOS flash update disk for Linux only ; to

be extracted by: "dd if= filename of=/dev/fd0" .\DOS\??CRISIS????ARJ.EXE Self extracting archive of DOS based flash crisis disk for MS-

DOS. Needs a prepared bootable floppy or MemCard .\DOS\??CRISIS????IMG.EXE Directly creates a bootable DOS based flash crisis disk on

1,44MB/3,5" floppy. To be created with Windows only . .\DOS\??CRISIS????DD.BIN Floppy image file of flash crisis disk for Linux only ; to be

extracted by: "dd if= filename of=/dev/fd0" .\WIN\*.* All files for Windows based BIOS update .\BEETLEview\*.HTM How to perform remote update; incl. direct links to EXTRANET README.PDF This information ???? .............................. Actual BIOS release number ?? ….……………………. Motherboard type

Contents of this README file CONTENTS OF DOWNLOAD.ZIP 1 CONTENTS OF THIS README FILE 1 GENERAL REMARKS 2 WHAT’S NEW? 2 REMARKS 2 DOS BASED UPDATE PROCEDURE (RELEASE 3.8): 2 SELF EXTRACTING ARJ ARCHIVES FOR DOS 3 CRISIS DISK FOR BIOS RECOVERY 3 MORE INFO 3 BIOS UPDATE WHEN RUNNING WINDOWS 4 TO UPDATE YOUR BIOS PLEASE OBSERVE THE FOLLOWING INSTRUCTIONS : 4 INTRODUCTION TO BEETLEVIEW BASED BIOS UPDATES 5 LSM 8.1 �� HOW TO PERFORM THE REMOTE UPDATE? 5 WHERE TO FIND README AND UPDATE FILES? 5 HOW TO USE DOS BASED FLASH TOOL "UPBIOS.EXE" 6 GENERAL : 6 OPTIONS: 7 CONFIGURATION FILE UPBIOS.CFG: 8 SECURITY: 9 BACK FLASHING : 9 PLAUSIBILITY : 9 COMMAND LINE EXAMPLES : 10 HISTORY OF STD BIOS RELEASES FOR BEETLE WITH D2 ST ANDARD MOTHERBOARD (I815E CHIPSET) 12


README.PDF 2 / 46

General remarks

What’s new? � The BIOS now calculates and shows a wider metering range for fan speed in

HARDWARE MONITOR of SETUP screens. Therefore, values of our new fans with lower speed will be shown correctly.This is the only change across from previous BIOS release!

� Discription of BIOS SETUP default values corrected here in README.PDF PS/2 mouse is ENABLED after CMOS reset (by F9 key)

Remarks � If running BEETLEview with this new BIOS release, you need to install the WN

tool “AdjBV.Exe”. Otherwise wrong values for fan speed may be displayed!!! See INTRANET � RETAIL PRODUCTS � SYSTEM SOFTWARE � ADD Ons

� If CMOS reset is initiated by F9 key, BIOS SETUP option “IRQ-routing COM3 COM4 ” is shown only after next reboot!

DOS based update procedure (release 3.8): If any of these advanced features is wanted, you need to adapt the update floppy disk! See chapter "How to use flash tool UPBIOS.EXE" for further information about options.

� One main feature of this releases is the automatic start of BIOS update after boot up of floppy! You are not prompted to confirm flash update, but you may abort the automatic procedure, when asked.

� It provides output to external line displays for BEETLE with or without VGA adapter.

� Another new feature of update procedure is the support of CMOS setup data save/restore . You can set setup options as wanted, than create an image file of BIOS setup data and after easily write the certain settings from image file to CMOS memory while BIOS flash update procedure! �� If POS BIOS is base for update, CMOS will be clear ed by flash procedure (release >= 3.8).


README.PDF 3 / 46

Self extracting ARJ archives for DOS The self extracting ARJ archives ( *ARJ.EXE), are basically made for DOS, but they do extract all data under Windows as well.

The UPDATE archive extracts files directly to a floppy in drive A:\ You need to rename the archive file to "8.3 format" before running it on a DOS system. It is good practise to store and run the ARJ self extractor in root folder or C:\TEMP, because it is a DOS based tool which does not support long folder paths. Always prepare the update disk by DOS command line "format a: /s" .

Crisis disk for BIOS recovery If there is a power fail during programming or BIOS update failed by other reasons, use the CRISIS DISK for recovery. To be found in the same DOWNLOAD.ZIP file. The CRISIS recovery is available for DOS only.

If Windows is your operating system, you need to use the crisis disk image *CRISIS*IMG.EXE to create a crisis boot disk!

DOS based systems require the ARJ self extracting archive, which extracts to folder C:\CRISIS . Use “C:\CRISIS\CRISDISK.BAT” to build a crisis disk. You do need to boot up a DOS system - this can not be done in a Windows command box! Since a certain minimal, non standard DOS (without screen output) is needed for crisis recovery, do not use DOS commands "format" or "sys". Detailed information you also find in README.TXT in archives / image files.

More info This release is not valid for D2 basic motherboard


README.PDF 4 / 46

BIOS update when running Windows If updating the BIOS on a BEETLE platform be sure to start update from appropriate BIOS version. Otherwise you first have to run the DOS version of BIOS update procedure and prepare the system for in future Windows based updates. BIOS update can be performed with this package under Windows 9x, NT, 2000 or XP. If running under Windows NT, 2000 or XP ensure that you have administrative rights.

To update your BIOS please observe the following in structions: 1) Unzip all files of the *update????win*.exe to a temporary directory on the

target system to be updated. It’s good practice to choose a simple folder name like “C:\BIOS ”

2) Execute the unzipped file RUNWPH.BAT. This will start the check and update procedure without any interaction needed. Don’t click any button inside the WinPhlash® window. Wait until this (�) dialog in shown. WinPhlash® will report the progress of the update continuously. During that time DO NOT POWER OFF or DO NOT REBOOT the system.

3) After successful update WinPhlash® will perform an automatic reboot .

Note, WinPhlash® must not be executed directly, as this would circumvent the plausibility checks!

Depending on previous BIOS version the Setup parameters may be preserved or substituted by default values. Check system functionality to ensure it works as before. If not, reboot and enter Setup to select desired options.

WinPhlash® writes a log file PHASH.LOG. This can be helpful to refer to in case of a problem. If flashing the BIOS was performed successfully, delete all files from the temporary directory used for BIOS update.

WinPhlash® is registered to Phoenix Technologies Ltd.


README.PDF 5 / 46

Introduction to BEETLEview based BIOS updates The standard production releases of WN STD BIOS for all new motherboards are available as BEETLEview update packages , provided for older release LANDesk Client Manager (LDCM) and for newer LANDesk System Manager (LSM) in www.

The BEETLEview based online update procedure requires at minimum the D2 STD BIOS release 09/09 as base for update to same or higher releases.

LSM 8.1 �� How to perform the remote update? Note, with LSM the remote BIOS update is possible, if ADMIN (any PC) and CLIENT (BEETLE) are installed on the same BEETLE system.

Note, before starting online update ensure that certificate already is installed while BEETLEview client installation before!

There is only one BEETLE view (LSM) package to be installed:

� BIOS update MFS environment

BEETLE view handles BEETLE BIOS update like any other software installation! Each installation requires two steps on ADMIN system:

Download from internet to ADMIN system: Select “Manage computers” menu and click this symbol …

If successfully done, you will be asked to install packages on clients , or choose this button …

Where to find README and UPDATE files? http://extranet.wincor-nixdorf.com/rd/beetledownload/winlsm /motherboards...

…/d2std/bios/WN_D2STD0D25_BIOS.txt …/d2std/bios/WN_D2STD0D25_BIOS.mfs

The MFS file path is needed for BEETLEview URL field! TXT files contain README information.


README.PDF 6 / 46

How to use DOS based flash tool "UPBIOS.EXE" This information is also placed in README_3.TXT on floppy.

General: UPBIOS.EXE is designed for easy support of Phoenix® PHLASH.EXE tool. Update procedure is running automatically, configurable via UPBIOS.CFG configuration file and via arguments from command line. All messages are minimized and optimized for use of 2x20 lines displ ay. No need of key-board input, but abort of procedure is possible. Beep support is provided for abort option (one double beep), successful operation (two double beeps) and error messages (three double beeps).

UPBIOS.EXE is used for DOS based flash update of POS- and STD BIOS

Options are selectable from command line. It might be useful to create an AUTOEXEC.BAT providing the complete command line.

Configuration is done via UPBIOS.CFG configuration file. See next page…

Introduced with release 3.8 (provided with BIOS 0D/25 and higher): CMOS data will be cleared if POS BIOS is base for update.


README.PDF 7 / 46

Options: Calling syntax: UPBIOS [com3] [cdump] [cload] [t] [q] [p] [m n] [over] [anyway] Any options may be mixed, but if cdump is selected, no BIOS update will be done. Options from command line will override appropriate keyword properties in UPBIOS.CFG.

com3: if BA6x on COM3 is available, screen output will be redirected to COM3.

cdump: Make a CMOS copy of actual system into the file CMOSDUMP.IMG. No BIOS update will be done.

cload: Before BIOS update, CMOS of actual system will be loaded from file CMOSDUMP.IMG

t: Test mode for debugging problems only, no BIOS update will be done.

q: Quick mode is waiting between 2-line-messages and beeps will be overrun

p: Production mode does not use Phoenix(R) screening while flashing (always used with com3-option)

M n: Mode: force flash mode n overrides automatic mode recognition: if n=1, flashes DMI area only if n=4, flashes BIOS area only if n=5, flashes BIOS + DMI if n=6, flashes BIOS + boot block if n=7, flashes BIOS + boot block + DMI

over: Overwrite ignores message "->no update needed" and reflash BIOS, but without clearing checksum of CMOS; so, Setup will not reset to default values.

anyway: ignore error messages from UPBIOS.EXE that would abort BIOS update

any other option will break and display options available.


README.PDF 8 / 46

Configuration file UPBIOS.CFG: Configuration is done via UPBIOS.CFG . Keywords must begin in column 0 and spell exactly until ":". Arguments have to follow immediately. Number and order of lines do not matter. Keywords work as follows:

Required: biosversion: ID of new BIOS version to be flashed. Both IDs from

old BIOS and new BIOS. If both IDs are identical, update will be aborted must-be-keys may be defined by BIOS development only!

Bootblock ID of new boot block to be flashed, compared by UPBIOS.EXE before any flash action.

Optional: cmosversion: CMOS checksum will not be cleared, if found BIOS

version of previous Bios is equal or higher to value of CMOS version. Superior condition is BIOS does not detect any checksum error after reboot. Keyword may be defined by Bios development only!

dmiversion: DMI data will be initialized, if found biosversion of previous BIOS is lower to value of dmiversion.

testversion: set by Bios development only to message testversions to be flashed

testflag: Set by Bios development only to debug problems. Will be OR-ed with "t" option

production: "1" inhibits Phoenix® PHLASH interface. Will be OR-ed with "p" option.

ramdisk: Will install a RAM disk and run upbios.exe from installed RAM disk. (Drive c: to o:)

modeflag: overrides automatic mode recognition: if 1, flashes DMI area only if 4, flashes BIOS area only if 5, flashes BIOS + DMI if 6, flashes BIOS + Bootblock if 7, flashes BIOS + Bootblock + DMI


README.PDF 9 / 46

Security: After calling upbios.exe all needed files are checked to be available. Using option "cload", writing to CMOS area is possible only, if header of "cmosdump.img" corresponds to system platform and biosversion to be flashed. Otherwise upbios.exe breaks and reports error. Hardware platforms (D1, D2, E1) are checked via bootblock check to avoid system breakdown after flashing with Bios that is not designed for that hardware. Crossover flashing from STD/POS(D2)-Bios to BAS(D2)-Bios (and reverse) is not possible.

Back flashing: Since 00/00 is the very first release, back flashing is not a topic for E1 motherboard, like it was for D2/D2* ones.

Plausibility: DMI data area will be checked and reflashed only, if actual DMI data area is corrupted or not available (flashing from POS to STD Bios). In addition option "dmiversion" will determine when to initialize DMI data area during Bios upgrade. Flashing from WN STD 00/00 to POS BIOS will generate DMI error message.

Error message may be overridden with command line option "anyway" or interactively by request.

CMOS Checksum will not be cleared, if - the "cload" option was used OR - the "cmosversion:"-parameter in "upbios.cfg" is equal or higher to biosversion ID found in actual system. Not clearing the CMOS checksum will prevent system from asking for F1 or F2 keys during first boot after reflashing and will preserve systems actual configuration. Upbios.exe will report success and will NOT reflash Bios, if biosversion and bootblockversion found in actual system correspond to the values of must-be-keys in "upbios.cfg".


README.PDF 10 / 46

Command line examples: "upbios" normal call using "upbios.cfg" for configuration, no options

"upbios com3" as before, using display on COM3 if available

"upbios cdump" creating CMOS-image from actual system, no Bios update

"upbios cload" load CMOS-image (if available) into CMOS, followed by Bios update

"upbios cload q p" load CMOS-image (if available) into CMOS, followed by Bios update; no beeps, no waiting during text scrolling, no Phoenix Phlash-Screen; fastest way of Bios update inclusive Setup configuration

"upbios m 7" disable automatic flashmode, forcing BIOS+Bootblock+DMI to be flashed "upbios anyway" run upbios ignoring all possible errormessages


README.PDF 11 / 46

Example configuration file "upbios.cfg" ################################################### #### # Note: The configuration area for any biosversio n # will alyways be defined by Bios developm ent! ################################################### #### # # ################################################### #### # # UPBIOS [com3] [cdump | cload] # ============================= # com3 : use display connected to COM3 if availabl e # cdump: create CMOSDUMP.IMG from actual system # cload: update Bios and load CMOS with CMOSDUMP.I MG # ################################################### #### # #remove leading #-characters to activate keywords. # #needed============================================ ==== # #biosversion:WN XXX aa/bb new BIOS ID #bootblock:X/Y new BB ID # #optional========================================== ==== # #cmosversion:aa/bb no CMOS checksum clearin g, if updating # from Biosversion aabb or higher #dmiversion:aa/bb no DMI data area clearin g, if updating # from Biosversion aabb or higher #testversion: any string #testflag:0 if 1, messaging variable s and preventing flashing #production:0 if 1, does not use Phoen ix Phlash Interface #ramdisk:0 if 1, uses Ramdisk for Up date #modeflag:x overrides automatic mode recognition: # 0 # 1 flashes DMI area only # 4 flashes BIOS area only # 5 flashes BIOS + DMI # 6 flashes BIOS + Bootblock # 7 flashes BIOS + Bootblock + DMI # ################################################### ############### ################################################### ############### # Configuration area: ################################################### ############### biosversion:WN STD 08/18 bootblock:2SA dmiversion:03/06 cmosversion:07/16 production:1


README.PDF 12 / 46

History of STD BIOS releases for BEETLE with D2 standard motherboard (i815E chipset)

RELEASE INFO 0E/26

1.Based on Release No.: 0D/25 2.Requirements/Dependences Subpoints: Hardware - This Bios 0E/26 is suited to run on all boards used for Biosversion 0D/25 Software - none 3.Removed Errors/Error-No.: - BIOS - none - SETUP - none 4.New Functions/enhanced Functions - BIOS The only modification in code is done due to prob lems with slow running fans (see Setup) - SETUP - Hardware Monitor with modified scale of measuri ng fan speed. Moved down minimum speed to be recognized to ab out 650 rpm, while decreasing the resolution by factor 4. Th is is done for CPU-Fan and Auxilary Fan 5.Functions under development - none 6.Additional remarks - This BIOS works for BEETLE CPU Pentium (D2-CPU) , acting as Standard Version to support standard applications . It will come up with the following signon text: WN STD 0E/26 (D2) 11/06/2006 Use D2BIOS0E_IMG.EXE to create a BIOS-Update-Flop py. Use D2CRIS0E_IMG.EXE to create a BIOS-Recovery-Fl oppy. Note: Upgrading this Bios from version 0D/25 will not reset CMOS Setup to default values, as CMOS map of those versions are identical.


README.PDF 13 / 46

After corrupted checksum the BIOS will set these de faults: Main ==== Diskette A: 1.44 MB Diskette B: Disabled >Primary Master: Auto >Primary Slave: Auto >Secondary Master: Auto >Secondary Slave: Auto Advanced ======== Reset Configuration Data: No Speaker Volume High PS/2 Mouse: Enabled Large Disk Access Mode: DOS Legacy USB Support: Disabled USB TimeOut Value: High {Note1} Onboard LAN BootProm: Enabled QuickBoot Mode: Disabled Video output to COM3 Disabled {Note2} >Chipset Configuration Local Bus IDE adapter: Both SMART Device Monitoring: Disabled ISA graphics device: No Boot-Video device: Onboard PCI 2.1 Support: Enabled >I/O Device Configuration Serial Port A: Enabled Base I/O address / IRQ: 3F8/IRQ4 Serial Port B: Enabled Base I/O address / IRQ: 2F8/IRQ3 Parallel Port: Enabled Mode: Bi-directional Base I/O address: 378 TouchScreen Routing: Route to COM2 IRQ-Routing COM3 COM4 COM3_I10 COM4_I10 {Note2 } >PCI/PNP ISA UMB Region Exclusion Bios Internal Buffer: E000 - E3FF CC00 - CFFF: Available D000 - D3FF: Available D400 - D7FF: Available D800 - DBFF: Available DC00 - DFFF: Available >PCI/PNP ISA IRQ Resource Exclusion IRQ 3: Available IRQ 4: Available IRQ 5: Available IRQ 7: Available IRQ 9: Reserved (see ATTENTION ->) IRQ 10: Reserved (see ATTENTION ->) IRQ 11: Available IRQ 12: Available


README.PDF 14 / 46

>DMI Event Logging Clear all DMI event logs: No Event Logging: Enabled Security ======== Set Supervisor Password Enter Processor Serial Number Disabled {Note3} Power ===== Power State: Stay Off Power Savings: Disabled Resume On Time: Disabled Resume Time: 00:00:00 Wakeup On Modem Ring: Disabled Wake Up On LAN: Disabled >Hardware Monitor Boot ==== Boot Order: Fol low Setup Order {Note1} +Removable Devices +Hard Drive CD-Rom Drive Network Boot =================================================== ==================== Note1: Value not changeable as long as "Legacy USB Support: [Disabled]" Note2: Node only visible if COM3/COM4 is available Note3: Node only visible if function is supported b y processor

RELEASE INFO 0D/25 (for internal user: see also ECO )

1.Based on Release No.: 0C/23 2.Requirements/Dependences

Hardware - This Bios 0D/25 is suited to run on "D2* Tualatin Board Print

D" and later, which MUST use any BIOS from 09/19 an d later to run properly

- This BIOS 0D/25 is compliant to former D2* Tualat in Board

prints and also to "D2 Standard Boards Print E" and later

- This BIOS 0D/25 is usable also in D2-ULV-Motherb oards Software - none

3.Removed Errors/Error-No.: - BIOS - Advanced system initialisation after replacing onboard battery, avoiding spurious hangup during POST - Fixed problem when Windows OS "Shutdown" selec ted. No accidential reboot anymore after Power Butt on had been pressed anytime during last session - Fixed problems with accidential wiping DMI dat a after trying to update any entries - SETUP


README.PDF 15 / 46

- Updating Bios 0D/25 running DOS will keep setup values selected in Bios 0C/23 4.New Functions/enhanced Functions - BIOS - Updatetool running Winphlash will make sure the platform to be an D2-STD-Motherboard before updating 0D/2 5 - Supporting critical initialisation of WN-printer USB TP07 - Automatic executing "Reset Config Data" after Bi os-Update avoiding problems when enumerating system config uration - SETUP - Hardware Monitor with "Auxilary Fan Speed" suppo rting speed display for boards employing additional 2n d fan connector - Updating Bios 0D/25 running WinFlash will keep setup values selected in Bios 0C/23 - Changed default for "TouchScreen Routing" == "TFT Touch to COM2" - Changed default for "PS/2 Mouse" == "Enabled" 5.Functions under development - none 6.Additional remarks - This BIOS works for BEETLE CPU Pentium (D2-CPU), acting as Standard Version to support standard applications. It will come up with the following signon text: WN STD 0D/25 (D2) 11/12/2004 Note: Upgrading this Bios from version 0C/23 will not reset CMOS Setup to default values, as CMOS map of those versions are identical. - Checksum: 9BACh - ECO: 017 3765/04 - MODULNO1: 1750033326 - PROMSETPN: A3C80100352 - RAWMATPN: A3C40027674 - LABELTEXT: 003530D01-9BACh - PROGR-FORMAT: INTEL MCS-86HEX After corrupted checksum the BIOS will set its defa ult to the following values: Main ==== Diskette A: 1.44 MB Diskette B: Disabled >Primary Master: Auto >Primary Slave: Auto >Secondary Master: Auto >Secondary Slave: Auto Advanced


README.PDF 16 / 46

======== Reset Configuration Data: No Speaker Volume High PS/2 Mouse: Enabled Large Disk Access Mode: DOS Legacy USB Support: Disabled USB TimeOut Value: High {Note1} Onboard LAN BootProm: Enabled QuickBoot Mode: Disabled Video output to COM3 Disabled {Note2} >Chipset Configuration Local Bus IDE adapter: Both SMART Device Monitoring: Disabled ISA graphics device: No Boot-Video device: Onboard PCI 2.1 Support: Enabled >I/O Device Configuration Serial Port A: Enabled Base I/O address / IRQ: 3F8/IRQ4 Serial Port B: Enabled Base I/O address / IRQ: 2F8/IRQ3 Parallel Port: Enabled Mode: Bi-directional Base I/O address: 378 TouchScreen Routing: Route to COM2 IRQ-Routing COM3 COM4 COM3_I10 COM4_I10 {Note 2} >PCI/PNP ISA UMB Region Exclusion Bios Internal Buffer: E000 - E3FF CC00 - CFFF: Available D000 - D3FF: Available D400 - D7FF: Available D800 - DBFF: Available DC00 - DFFF: Available >PCI/PNP ISA IRQ Resource Exclusion IRQ 3: Available IRQ 4: Available IRQ 5: Available IRQ 7: Available IRQ 9: Reserved (see ATTENTION ->) IRQ 10: Reserved (see ATTENTION ->) IRQ 11: Available IRQ 12: Available >DMI Event Logging Clear all DMI event logs: No Event Logging: Enabled Security ======== Set Supervisor Password Enter Processor Serial Number Disabled {Note3} Power ===== Power State: Stay Off Power Savings: Disabled Resume On Time: Disabled Resume Time: 00:00:00


README.PDF 17 / 46

Wakeup On Modem Ring: Disabled Wake Up On LAN: Disabled >Hardware Monitor Boot ==== Boot Order: Fol low Setup Order {Note1} +Removable Devices +Hard Drive CD-Rom Drive Network Boot =================================================== =============== Note1: Value not changeable as long as "Legacy USB Support: [Disabled]" Note2: Node only visible if COM3/COM4 is available Note3: Node only visible if function is supported by processor

RELEASE INFO 0C/23 ( for internal user: see also ECO )

1.Based on Release No.: 09/19

but includes all project improvements of 0B/22 2.Requirements/Dependences Subpoints: Hardware - This Bios 0C/23 is suited to run on "D2* Tualatin Board Print D" and later, which MUST use any BIOS from 09/19 and later to run properly. - This BIOS 0C/23 is compliant to former D2* Tualatin Board prints and also to "D2 Standard Boards Print E" and later - This BIOS 0C/23 is the first BIOS to be used in D2-ULV-Motherboards Software - none 3.Removed Errors/Error-No.: - BIOS - Fixed problems with systems behaviour after power failure / power return. (Power State: "Stay Off" and "Follow AC/Power" ) - Added support for IBM X-25 Interface Card - Fixed problem with touchpad hang up running TA 59 under WIN2000 - During boot up messages directed to BA6x-displ ays (connected to COM3) will be cut to 20 characte rs per line avoiding to long periods of closed in terrupts. - SETUP - none 4.New Functions/enhanced Functions - BIOS - replaced fixed value of temperature limit for starting processor-throttlemode with processor-dependant values due to data sheet


README.PDF 18 / 46

- Included latest version of Intel Boot Agent PXE 4.1.10 - upgradable from Bios 0B/22 using RemoteFlash under Windws OS - Locking of BootBlock Protection removed due to the need of RemoteFlash Managing - No waiting any more for F1/F2 keys when CMOS v alues were loaded with default values after CMOS checksum error. This is necessary due to RemoteFlash of Bios. - Support of COM-Interface POS/485 - Enhanced support for SANDISK USB CompactFlash. If used, USB TimeOut Value [Low] should be sel ected for best performance - SETUP - New entry: "Boot / Boot Order" == [Follow Setu p Order / Override Setup Order] If "Legacy USB Support" is enabled AND any USB HardDrive (also HD-formatted MemoryStick) was detected, then "Override Setup Order" will use this device as FIRST bootdevice (See helptext in Setup) - "Advanced / Legacy USB support" == [Disabled] will: - reset and lock the entry "Boot / Boot Order" == [Follow Setup Order] - lock the entry "Advanced / USB-TimeOut Value" - "Advanced / Legacy USB support" == [Enabled] w ill: - release the entry "Boot / Boot Order" - release the entry "Advanced / USB-TimeOut Val ue" 5.Functions under development - none 6.Additional remarks - This BIOS works for BEETLE CPU Pentium (D2-CPU) , acting as Standard Version to support standard applications . It will come up with the following signon text: WN STD 0C/23 (D2) 03/11/2004 Use D2BIOS0C.EXE to create a BIOS-Update-Floppy. Use D2CRIS0C.EXE to create a BIOS-Recovery-Floppy . Note: Upgrading this Bios from version 0A/20 or 0 B/22 will not reset CMOS Setup to default values, as CMOS map of those versions are identical. - Checksum: 54FAh - ECO: 017 1748/03 - MODULNO1: 1750033326 - PROMSETPN: A3C80100352 - RAWMATPN: A3C40027674 - LABELTEXT: 003530C01-54FAh - PROGR-FORMAT: INTEL MCS-86HEX After corrupted checksum the BIOS will set its def ault to the following values: Main ==== Diskette A: 1.44 MB Diskette B: Disabled


README.PDF 19 / 46

>Primary Master: Auto >Primary Slave: Auto >Secondary Master: Auto >Secondary Slave: Auto Advanced ======== Reset Configuration Data: No Speaker Volume High PS/2 Mouse: Disabled Large Disk Access Mode: DOS Legacy USB Support: (Disabled) USB TimeOut Value: High Onboard LAN BootProm: Enabled QuickBoot Mode: Disabled (Video output to COM3 Disabled) >Chipset Configuration Local Bus IDE adapter: Both SMART Device Monitoring: Disabled ISA graphics device: No Boot-Video device: Onboard PCI 2.1 Support: Enabled >I/O Device Configuration Serial Port A: Enabled Base I/O address / IRQ: 3F8/IRQ4 Serial Port B: Enabled Base I/O address / IRQ: 2F8/IRQ3 Parallel Port: Enabled Mode: Bi-directional Base I/O address: 378 TouchScreen Routing: No Routing (IRQ-Routing COM3 COM4 COM3_I10 COM4_I10) >PCI/PNP ISA UMB Region Exclusion Bios Internal Buffer: E000 - E3FF CC00 - CFFF: Available D000 - D3FF: Available D400 - D7FF: Available D800 - DBFF: Available DC00 - DFFF: Available >PCI/PNP ISA IRQ Resource Exclusion IRQ 3: Available IRQ 4: Available IRQ 5: Available IRQ 7: Available IRQ 9: Reserved (see ATTENTION ->) IRQ 10: Reserved (see ATTENTION ->) IRQ 11: Available IRQ 12: Available >DMI Event Logging Clear all DMI event logs: No Event Logging: Enabled Security ======== Set Supervisor Password Enter (Processor Serial Number) Disabled Power ===== Power State: Stay Off Power Savings: Disabled Resume On Time: Disabled Resume Time: 00:00:00


README.PDF 20 / 46

Wakeup On Modem Ring: Disabled Wake Up On LAN: Disabled >Hardware Monitor Boot ==== Boot Order: (Fo llow Setup Order) +Removable Devices +Hard Drive CD-Rom Drive Network Boot


README.PDF 21 / 46

RELEASE INFO 0B/22 ( for internal user: see also ECO )

1.Based on Release No.: 0A/20 2.Requirements/Dependences Subpoints: Hardware

- This Bios 0B/22 is suited to run on "D2* Tualatin Board Print D" and later, which MUST use any BIOS from 09/19 and later to run properly. - This BIOS 0B/22 is compliant to former D2* Tualatin Board prints and also to "D2 Standard Boards Print E" and later Software - none 3.Removed Errors/Error-No.: - BIOS - Fixed problem with touchpad hangup running TA5 9 under WIN2000 - During bootup messages directed to BA6x-displa ys (connected to COM3) will be cut to 20 characte rs per line avoiding to long periods of closed interrupts. - SETUP - none 4.New Functions/enhanced Functions - BIOS - First Biosversion that might be ubgraded to higher versions using RemoteFlash under Windws OS - Locking of BootBlock Protection removed due to the need of RemoteFlashing Managing - No waiting for F1/F2 keys when CMOS values wer e loaded with default values after CMOS checksum error. This is necessary due to RemoteFlash of Bios. - Support of COM-Interface POS/485 - SETUP - Saving order of bootdevices when bootdevice is removed. Bootorder will be restored to saved order, if removed bootdevice will be added some time later. (Useful for booting from USB-Memorystick) 5.Functions under development - none 6.Additional remarks - This BIOS works for BEETLE CPU Pentium (D2-CPU) , acting as


README.PDF 22 / 46

Standard Version to support standard applications . It will come up with the following signon text: WN STD 0B/22 (D2) 10/22/2003 Use D2BIOS0B.EXE to create a BIOS-Update-Floppy. Use D2CRIS0B.EXE to create a BIOS-Recovery-Floppy . Note: Upgrading this Bios from version 0A/20 will not reset CMOS Setup to default values, as CMOS map of both versions are identical. - Checksum: BDA4h - ECO: 017 3093 03 - MODULNO1: 1750033326 - PROMSETPN: A3C80100352 - RAWMATPN: A3C40027674 - LABELTEXT: 003530B01-BDA4h - PROGR-FORMAT: INTEL MCS-86HEX After corrupted checksum the BIOS will set its de fault to the following values: Main ==== Diskette A: 1.44 MB Diskette B: Disabled >Primary Master: Auto >Primary Slave: Auto >Secondary Master: Auto >Secondary Slave: Auto Advanced ======== Reset Configuration Data: No Speaker Volume High PS/2 Mouse: Disabled Large Disk Access Mode: DOS Legacy USB Support: Disabled USB TimeOut Value: High Onboard LAN BootProm: Enabled QuickBoot Mode: Disabled (Video output to COM3 Disabled) >Chipset Configuration Local Bus IDE adapter: Both SMART Device Monitoring: Disabled ISA graphics device: No Boot-Video device: Onboard PCI 2.1 Support: Enabled >I/O Device Configuration Serial Port A: Enabled Base I/O address / IRQ: 3F8/IRQ4 Serial Port B: Enabled Base I/O address / IRQ: 2F8/IRQ3 Parallel Port: Enabled Mode: Bi-directional Base I/O address: 378


README.PDF 23 / 46

TouchScreen Routing: No Routing (IRQ-Routing COM3 COM4 COM3_I10 COM4_I10) >PCI/PNP ISA UMB Region Exclusion Bios Internal Buffer: E000 - E3FF CC00 - CFFF: Available D000 - D3FF: Available D400 - D7FF: Available D800 - DBFF: Available DC00 - DFFF: Available >PCI/PNP ISA IRQ Resource Exclusion IRQ 3: Available IRQ 4: Available IRQ 5: Available IRQ 7: Available IRQ 9: Reserved (see ATTENTION ->) IRQ 10: Reserved (see ATTENTION ->) IRQ 11: Available IRQ 12: Available >DMI Event Logging Clear all DMI event logs: No Event Logging: Enabled Security ======== Set Supervisor Password Enter (Processor Serial Number) Disabled Power ===== Power State: Stay Off Power Savings: Disabled Resume On Time: Disabled Resume Time: 00:00:00 Wakeup On Modem Ring: Disabled Wake Up On LAN: Disabled >Hardware Monitor Boot ==== +Removable Devices +Hard Drive CD-Rom Drive Network Boot

RELEASE INFO 0A/20 ( for internal user: see a lso ECO )

1.Based on Release No.: 09/19 2.Requirements/Dependences Subpoints: Hardware - This actual Bios is suited to run on "D2* Tualatin Board Print D" and l ater,


README.PDF 24 / 46

which MUST use any BIOS from 09/19 and later to run properly. - This actual BIOS is compliant to f ormer D2* Tualatin Board prints and also to "D2 Standard Boards Print E" and l ater Software - none 3.Removed Errors/Error-No.: - BIOS - Fixed problems with systems behaviour after power failure / power return. (Power State: "Stay Off" and "Follow A C/Power") - Added support for IBM X-25 Interface - SETUP - none 4.New Functions/enhanced Functions - BIOS - replaced fixed value of temperature li mit for starting processor-throttlemode with processor-dependant values due to data sheet - Included latest version of Intel Boot Agent PXE 4.1.10 - SETUP - new entry: "Advanced // PCI/PNP ISA UMB Region Ex clusion": "Bios Internal Buffer:" This selector allows limiting availabl e UMB area to DBFFh or DFFFh, thus freeing up memory addresses especially needed by customers add-on- cards. So, resources problems with "Dotcard 5 50" or "IDE Raid Controller" can be solved wi thin one Bios version. 5.Functions under development/enhanced Functions - none 6.Additional remarks - This BIOS works for BEETLE CPU Pentium (D2 -CPU), acting as Standard Version to support standard applica tions. It will come up with the following signon te xt: WN STD 0A/20 (D2) 06/20/2003 Use D2BIOS0A.EXE to create a BIOS-Update-Flo ppy. Use D2CRIS0A.EXE to create a BIOS-Recovery-F loppy. - Checksum: 76F6h - ECO: 017 1748 03 - MODULNO1: 1750033326 - PROMSETPN: A3C80100352 - RAWMATPN: A3C40027674 - LABELTEXT: 003530A01-76F6h - PROGR-FORMAT: INTEL MCS-86HEX


README.PDF 25 / 46

After corrupted checksum the BIOS will set its def ault to the following values: Main ==== Diskette A: 1.44 MB Diskette B: Disabled >Primary Master: Auto >Primary Slave: Auto >Secondary Master: Auto >Secondary Slave: Auto Advanced ======== Reset Configuration Data: No Speaker Volume High PS/2 Mouse: Disabled Large Disk Access Mode: DOS Legacy USB Support: Disabled USB TimeOut Value: High Onboard LAN BootProm: Enabled QuickBoot Mode: Disabled (Video output to COM3 Disabled) >Chipset Configuration Local Bus IDE adapter: Both SMART Device Monitoring: Disabled ISA graphics device: No Boot-Video device: Onboard PCI 2.1 Support: Enabled >I/O Device Configuration Serial Port A: Enabled Base I/O address / IRQ: 3F8/IRQ4 Serial Port B: Enabled Base I/O address / IRQ: 2F8/IRQ3 Parallel Port: Enabled Mode: Bi-directional Base I/O address: 378 TouchScreen Routing: No Routing (IRQ-Routing COM3 COM4 COM3_I10 COM4_I10 ) >PCI/PNP ISA UMB Region Exclusion Bios Internal Buffer: E000 - E3FF CC00 - CFFF: Available D000 - D3FF: Available D400 - D7FF: Available D800 - DBFF: Available DC00 - DFFF: Available >PCI/PNP ISA IRQ Resource Exclusion IRQ 3: Available IRQ 4: Available IRQ 5: Available IRQ 7: Available IRQ 9: Reserved (see ATTE NTION ->) IRQ 10: Reserved (see ATTE NTION ->) IRQ 11: Available IRQ 12: Available


README.PDF 26 / 46

>DMI Event Logging Clear all DMI event logs: No Event Logging: Enabled Security ======== Set Supervisor Password Enter (Processor Serial Number) Disabled Power ===== Power State: Stay Off Power Savings: Disabled Resume On Time: Disabled Resume Time: 00:00:00 Wakeup On Modem Ring: Disabled Wake Up On LAN: Disabled >Hardware Monitor Boot ==== +Removable Devices +Hard Drive CD-Rom Drive Network Boot

RELEASE INFO 09/19 ( for internal user: see a lso ECO )

1.Based on Release No.: 08/18 2.Requirements/Dependences Hardware - "D2* Tualatin Board Print D" and later MUST use this BIOS 09/19 and later to run properly - This BIOS 09/19 is compliant to former D2* Tualatin Board prints and also to "D2 Standard Boards Print E" and later Software - none 3.Removed Errors/Error-No.: BIOS - Optimized DRAM BufferStrength for "Prin t D" - Fixed hangup problems with SanDisk CompactFlashReader - Fixed problem when using Dotcard 550 wi th Win2000 SETUP - ISA UMB Region Exclusion: removed addre sses D800h - DFFFh due to UMB reorganisation necessary for DMI data handling and Dotcard 550 i ssue


README.PDF 27 / 46

4.New Functions/enhanced Functions BIOS - none SETUP - Infosreen introduced for easy check of - Productname - Biosversion - Chipset_RevID - DMI entry of serialnumber (System, Mainboard and Powersupply) - New Submenu: - Advanced / ChipsetConfiguration - New Entry: - Advanced / ChipsetConfiguration: PCI 2.1 Support 5.Functions under development/enhanced Functions - none 6.Additional remarks - This BIOS works for BEETLE CPU Pentium (D2-CPU), acting as Standard Version to support standard ap plications. It will come up with the following sign on text: WN STD 09/19 02/28/2003 (D2) - Checksum: A01Bh - ECO: 017 0589 03 - MODULNO1: 1750033326 - PROMSETPN: A3C80100352 - RAWMATPN: A3C40027674 - LABELTEXT: 003530901-A01Bh - PROGR-FORMAT: INTEL MCS-86HEX After corrupted checksum the BIOS will set its default to the following values: Main ==== Diskette A: 1.44 MB Diskette B: Disabled >Primary Master: Auto >Primary Slave: Auto >Secondary Master: Auto >Secondary Slave: Auto Advanced ======== Reset Configuration Data: No Speaker Volume High PS/2 Mouse: Disabled Large Disk Access Mode: DOS Legacy USB Support: Disabled USB TimeOut Value: Low Onboard LAN BootProm: Enabled QuickBoot Mode: Disabled


README.PDF 28 / 46

(Video output to COM3 Disabled) >Chipset Configuration Local Bus IDE adapter: Both SMART Device Monitoring: Disabled ISA graphics device: No Boot-Video device: Onboard PCI 2.1 Support: Enabled >I/O Device Configuration Serial Port A: Enabled Base I/O address / IRQ: 3F8/IRQ4 Serial Port B: Enabled Base I/O address / IRQ: 2F8/IRQ3 Parallel Port: Enabled Mode: Bi-directional Base I/O address: 378 TouchScreen Routing: No Routing (IRQ-Routing COM3 COM4 COM3_I10 COM 4_I10) >PCI/PNP ISA UMB Region Exclusion CC00 - CFFF: Available D000 - D3FF: Available D400 - D7FF: Available >PCI/PNP ISA IRQ Resource Exclusion IRQ 3: Available IRQ 4: Available IRQ 5: Available IRQ 7: Available IRQ 9: Reserved (see A TTENTION ->) IRQ 10: Reserved (see A TTENTION ->) IRQ 11: Available IRQ 12: Available >DMI Event Logging Clear all DMI event logs: No Event Logging: Enabled Security ======== Set Supervisor Password Enter (Processor Serial Number) Disabled Power ===== Power State: Stay Off Power Savings: Disabled Resume On Time: Disabled Resume Time: 00:00:00 Wakeup On Modem Ring: Disabled Wake Up On LAN: Disabled >Hardware Monitor Boot ==== +Removable Devices +Hard Drive CD-Rom Drive Network Boot


README.PDF 29 / 46


1.Based on Release No.: 07/16 2.Requirements/Dependences Hardware - D2-Motherboard Print E and later - "D2* Tualatin Board Print C" and later must use this BIOS 07/16 and later to run properly Software - none 3.Removed Errors/Error-No.: - BIOS - fixed sporadic problem with R/W-access to NVRAM. 4.New Functions/enhanced Functions - none 5.Functions under development/enhanced Functions - none 6.Additional remarks - This BIOS works for BEETLE CPU Pentium (D 2-CPU), acting as Standard Version to support standard appl ications. It will come up with the following signon text: WN STD 08/18 02/10/2003 (D2) - Checksum: 7C88h - ECO: 017 0356 03 - MODULNO1: 1750033326 - PROMSETPN: A3C80100352 - RAWMATPN: A3C40027674 - LABELTEXT: 003530801-7C88h - PROGR-FORMAT: INTEL MCS-86HEX After corrupted checksum the BIOS will set its de fault to the following values: Main ==== Diskette A: 1.44 MB Diskette B: Disabled >Primary Master: Auto >Primary Slave: Auto >Secondary Master: Auto >Secondary Slave: Auto Advanced ======== Reset Configuration Data: No


README.PDF 30 / 46

Speaker Volume High Local Bus IDE adapter: Both SMART Device Monitoring: Disabled PS/2 Mouse: Disabled Large Disk Access Mode: DOS Legacy USB Support: Disabled USB TimeOut Value: Low ISA graphics device: No Boot-Video device: Onboard Onboard LAN BootProm: Enabled QuickBoot Mode: Disabled >I/O Device Configuration Serial Port A: Enabled Base I/O address / IRQ: 3F8/IRQ4 Serial Port B: Enabled Base I/O address / IRQ: 2F8/IRQ3 Parallel Port: Enabled Mode: Bi-directional Base I/O address: 378 TouchScreen Routing: No Routing (IRQ-Routing COM3 COM4 COM3_I10 COM4_ I10) >PCI/PNP ISA UMB Region Exclusion CC00 - CFFF: Available D000 - D3FF: Available D400 - D7FF: Available D800 - DBFF: Available DC00 - DFFF: Available >PCI/PNP ISA IRQ Resource Exclusion IRQ 3: Available IRQ 4: Available IRQ 5: Available IRQ 7: Available IRQ 9: Reserved (see A TTENTION ->) IRQ 10: Reserved (see A TTENTION ->) IRQ 11: Available IRQ 12: Available >DMI Event Logging Clear all DMI event logs: No Event Logging: Enabled (Video output to COM3 Disabled) Security ======== Set Supervisor Password Enter (Processor Serial Number) Disabled Power ===== Power State: Stay Off Power Savings: Disabled Resume On Time: Disabled Resume Time: 00:00:00 Wakeup On Modem Ring: Disabled Wake Up On LAN: Disabled >Hardware Monitor Boot ====


README.PDF 31 / 46

+Removable Devices +Hard Drive CD-Rom Drive Network Boot


1.Based on Release No.: 06/13 2.Requirements/Dependences Subpoints: Hardware - D2-Motherboard Prin t E and later - "D2* Tualatin Board Print C" and later must use this BIOS 07/16 and late r to run properly - Software Before flashing back BIOS from 07 /16 to earlier versions read file "fwhpa zch.txt" located on root of BIOS Update Di skette 3.Removed Errors/Error-No.: - BIOS - OS/2 system is able to boot - fixed sporadic problems with display at first booting after BIOS update 4.New Functions/enhanced Functions - BIOS: - DMI information located below 1MB area, avoiding problems using any DMI related tools - providing latest microcode for Tualatin processor - supporting video mode for Plasma Display "848x480 sync positiv" when using video jumpering #6 (open, open, closed ) - SETUP: - deleted entry: Advanced/IODeviceConfiguration: "Floppy Disk Controller: [Enabled/Disabled]" FDC will be configured automatically depending on "Legacy Diskette A:" and "Legacy Diskette B" - new entry: Advanced: "USB TimeOut Value: [Low/High] Selecting [Low] will cut waiting time during PO ST to initialize USB devices with no need to wait for long spin up time, i.e. CompactFlash 5.Functions under development/enhanced Functions - none 6.Additional remarks - This BIOS works for BEETLE CPU Pentium (D2-CPU), acting as Standard Version to support standard applications. It will come up with the following signon text:


README.PDF 32 / 46

WN STD 07/16 (D2) 09/27/2002 - Checksum: 784Ch - ECO: 017 2246 02 - MODULNO1: 1750033326 - PROMSETPN: A3C80100352 - RAWMATPN: A3C40027674 - LABELTEXT: 003530701-784Ch - PROGR-FORMAT: INTEL MCS-86HEX After corrupted checksum the BIOS will set its de fault to the following values: Main ==== Diskette A: 1.44 MB Diskette B: Disabled >Primary Master: Auto >Primary Slave: Auto >Secondary Master: Auto >Secondary Slave: Auto Advanced ======== Reset Configuration Data: No Speaker Volume High Local Bus IDE adapter: Both SMART Device Monitoring: Disabled PS/2 Mouse: Disabled Large Disk Access Mode: DOS Legacy USB Support: Disabled USB TimeOut Value: Low ISA graphics device: No Boot-Video device: Onboard Onboard LAN BootProm: Enabled QuickBoot Mode: Disabled >I/O Device Configuration Serial Port A: Enabled Base I/O address / IRQ: 3F8/IRQ4 Serial Port B: Enabled Base I/O address / IRQ: 2F8/IRQ3 Parallel Port: Enabled Mode: Bi-directional Base I/O address: 378 TouchScreen Routing: No Routing (IRQ-Routing COM3 COM4 COM3_I10 COM4_I10) >PCI/PNP ISA UMB Region Exclusion CC00 - CFFF: Available D000 - D3FF: Available D400 - D7FF: Available D800 - DBFF: Available DC00 - DFFF: Available >PCI/PNP ISA IRQ Resource Exclusion IRQ 3: Available IRQ 4: Available IRQ 5: Available


README.PDF 33 / 46

IRQ 7: Available IRQ 9: Reserved (see ATTENTION ->) IRQ 10: Reserved (see ATTENTION ->) IRQ 11: Available IRQ 12: Available >DMI Event Logging Clear all DMI event logs: No Event Logging: Enabled (Video output to COM3 Disabled) Security ======== Set Supervisor Password Enter (Processor Serial Number) Disabled Power ===== Power State: Stay Off Power Savings: Disabled Resume On Time: Disabled Resume Time: 00:00:00 Wakeup On Modem Ring: Disabled Wake Up On LAN: Disabled >Hardware Monitor Boot ==== +Removable Devices +Hard Drive CD-Rom Drive Network Boot


1.Based on Release No.: 05/11 2.Requirements/Dependences Subpoints: Hardware D2-Motherboard Pri nt E and newer Software none 3.Removed Errors/Error-No.: - BIOS - OS/2 system is able to boot - DMI information 32-bit-access possible - Setup - Modified function "Power / Power up" to "Power / Follow AC Power", which equals to "Power / Restore previous state" but the Frontpanel Power Switch is disabled - Default Speaker Volume == High 4.New Functions/enhanced Functions - BIOS: - COM3 interface may be used as display for POST and boot messages


README.PDF 34 / 46

- Removed from POST: - Display: xxx Cache SRAM Passed - Display: 8086/1130 Rev.ID = xx - Display: 8086/2440 Rev.ID = xx - SETUP: - "Advanced / Video output to COM3" 5.Functions under development/enhanced Functions - none 6.Additional remarks - This BIOS works for BEETLE CPU Pentium (D2 -CPU), acting as Standard Version to support standard applica tions. It will come up with the following signon te xt: WN STD 06/13 (D2) 06/06/2002 Use D2BIOS06.EXE to create a BIOS-Update-Flo ppy. Use D2CRIS06.EXE to create a BIOS-Recovery-F loppy. - Checksum: E616h - ECO: 017 1136 02 - MODULNO1: 1750033326 - PROMSETPN: A3C80100352 - RAWMATPN: A3C40027674 - LABELTEXT: 003530601-E616h - PROGR-FORMAT: INTEL MCS-86HEX After corrupted checksum the BIOS will set its def ault to the following values: Main ==== Diskette A: 1.44 MB Diskette B: Disabled >Primary Master: Auto >Primary Slave: Auto >Secondary Master: Auto >Secondary Slave: Auto Advanced ======== Reset Configuration Data: No Speaker Volume High Local Bus IDE adapter: Both SMART Device Monitoring: Disabled PS/2 Mouse: Disabled Large Disk Access Mode: DOS Legacy USB Support: Disabled ISA graphics device: No Boot-Video device: Onboard Onboard LAN BootProm: Enabled QuickBoot Mode: Disabled >I/O Device Configuration Serial Port A: Enabled Base I/O address / IRQ: 3F8/IRQ4 Serial Port B: Enabled Base I/O address / IRQ: 2F8/IRQ3


README.PDF 35 / 46

Parallel Port: Enabled Mode: Bi-directional Base I/O address: 378 Floppy Disk Controller: Enabled TouchScreen Routing: No Routing (IRQ-Routing COM3 COM4 COM3_I10 COM4_I 10) >PCI/PNP ISA UMB Region Exclusion CC00 - CFFF: Available D000 - D3FF: Available D400 - D7FF: Available D800 - DBFF: Available DC00 - DFFF: Available >PCI/PNP ISA IRQ Resource Exclusion IRQ 3: Available IRQ 4: Available IRQ 5: Available IRQ 7: Available IRQ 9: Reserved (see ATTENTI ON ->) IRQ 10: Reserved (see ATTENT ION ->) IRQ 11: Available IRQ 12: Available >DMI Event Logging Clear all DMI event logs: No Event Logging: Enabled (Video output to COM3 Disabled) Security ======== Set Supervisor Password Enter (Processor Serial Number) Disabled Power ===== Power State: Stay Off Power Savings: Disabled Resume On Time: Disabled Resume Time: 00:00:00 Wakeup On Modem Ring: Disabled Wake Up On LAN: Disabled >Hardware Monitor Boot ==== +Removable Devices +Hard Drive CD-Rom Drive Network Boot


1.Based on Release No.: 04/08


README.PDF 36 / 46

2.Requirements/Dependences Subpoints: Hardware D2-Motherboard Pri nt E Software none 3.Removed Errors/Error-No.: - Fixed problems with CompactFlashMemories - Fixed booting failure from some CDROMs - Fixed LED-update on Standard- and USB-Keyb oards running DOS and Windows 4.New Functions/enhanced Functions - BIOS: - Included Intel BootAgent Version 4.0.22 - Memory D000h -DFFFh completely to be reser ved, if Onboard LAN==Disabled - Message RevisionID of Device 1130 (GMCH) and Device 2440 (ICH2) during POST - BootBlockProtection implemented. No writin g possible from application into bootblock - SETUP: - Message RevisionID of Device 1130 (GMCH) and Device 2440 (ICH2) on "Main" screen - Display Extended Memrory Size in "MB" unit s - Moved "Speaker Volume" to "Advanced" scree n - Moved "Local Bus IDE Adapter" to "Advanced " screen - New function "QuickBoot Mode" in "Advanced " screen - New function "HDD-SmartMonitoring" in "Adv anced" screen - New entry "Power Up" in "Power State" on " Power" screen - Extended helptext for COM3 / COM4 entry on "Advanced" screen 5.Functions under development/enhanced Functions - none 6.Additional remarks - This BIOS works for BEETLE CPU Pentium (D2 -CPU), acting as Standard Version to support standard applica tions. It will come up with the following signon te xt: WN STD 05/11 (D2) 03/18/2002 Use D2BIOS05.EXE to create a BIOS-Update-Flo ppy. Use D2CRIS05.EXE to create a BIOS-Recovery-F loppy. - Checksum: 8A1Ah - ECO: 017 0662 02 - MODULNO1: 1750033326 - PROMSETPN: A3C80100352 - RAWMATPN: A3C40027674 - LABELTEXT: D2CPU After corrupted checksum the BIOS will set its def ault to the following values: Main ====


README.PDF 37 / 46

Diskette A: 1.44 MB Diskette B: Disabled >Primary Master: Auto >Primary Slave: Auto >Secondary Master: Auto >Secondary Slave: Auto Advanced ======== Reset Configuration Data: No Speaker Volume Middle Local Bus IDE adapter: Both SMART Device Monitoring: Disabled PS/2 Mouse: Disabled Large Disk Access Mode: DOS Legacy USB Support: Disabled ISA graphics device: No Boot-Video device: Onboard Onboard LAN BootProm: Enabled QuickBoot Mode: Disabled >I/O Device Configuration Serial Port A: Enabled Base I/O address / IRQ: 3F8/IRQ4 Serial Port B: Enabled Base I/O address / IRQ: 2F8/IRQ3 Parallel Port: Enabled Mode: Bi-directional Base I/O address: 378 Floppy Disk Controller: Enabled TouchScreen Routing: No Routing (IRQ-Routing COM3 COM4 COM3_I10 COM4_I 10) >PCI/PNP ISA UMB Region Exclusion CC00 - CFFF: Available D000 - D3FF: Available D400 - D7FF: Available D800 - DBFF: Available DC00 - DFFF: Available >PCI/PNP ISA IRQ Resource Exclusion IRQ 3: Available IRQ 4: Available IRQ 5: Available IRQ 7: Available IRQ 9: Reserved IRQ 10: Reserved IRQ 11: Available IRQ 12: Available >DMI Event Logging Clear all DMI event logs: No Event Logging: Enabled Security ======== Set Supervisor Password Enter (Processor Serial Number) Disabled Power ===== Power State: Stay Off Power Savings: Disabled


README.PDF 38 / 46

Resume On Time: Disabled Resume Time: 00:00:00 Wakeup On Modem Ring: Disabled Wake Up On LAN: Disabled >Hardware Monitor Boot ==== +Removable Devices +Hard Drive CD-Rom Drive Network Boot


1.Based on Release No.: 03/06 2.Requirements/Dependences Subpoints: Hardware D2-Motherboard Pri nt E Software none 3.Removed Errors/Error-No.: - Using the new MPS 1064 Power Supply with U SV (Magnum) the fan will not longer run with maximum s peed 4.New Functions/enhanced Functions - none 5.Functions under development/enhanced Functions - none 6.Additional remarks - This BIOS works for BEETLE CPU Pentium (D2 -CPU), acting as Standard Version to support standard applica tions. It will come up with the following signon te xt: WN STD 04/08 12/12/2001 (D2) Use D2BIOS04.EXE to create a BIOS-Update-Flo ppy. Use D2CRIS04.EXE to create a BIOS-Recovery-F loppy. - Checksum: 0A470h - ECO: 017 2791/01 - MODULNO1: 1750033326 - PROMSETPN: A3C80100352 - RAWMATPN: A3C40027674 - LABELTEXT: D2CPU After corrupted checksum the BIOS will set its def ault to the following values: Main


README.PDF 39 / 46

==== Diskette A: 1.44 MB Diskette B: Disabled >Primary Master: Auto >Primary Slave: Auto >Secondary Master: Auto >Secondary Slave: Auto Local Bus IDE adapter: Both Speaker Volume Middle Advanced ======== Reset Configuration Data: No PS/2 Mouse: Disabled Large Disk Access Mode: DOS Legacy USB Support: Disabled ISA graphics device: No Boot-Video device: Onboard Onboard LAN BootProm: Enabled QuickBoot Mode: Disabled >I/O Device Configuration Serial Port A: Enabled Base I/O address / IRQ: 3F8/IRQ4 Serial Port B: Enabled Base I/O address / IRQ: 2F8/IRQ3 Parallel Port: Enabled Mode: Bi-directional Base I/O address: 378 Floppy Disk Controller: Enabled TouchScreen Routing: No Routing (IRQ-Routing COM3 COM4 COM3____ COM4__ __) >PCI/PNP ISA UMB Region Exclusion CC00 - CFFF: Available D000 - D3FF: Available D400 - D7FF: Available D800 - DBFF: Available DC00 - DFFF: Available >PCI/PNP ISA IRQ Resource Exclusion IRQ 3: Available IRQ 4: Available IRQ 5: Available IRQ 7: Available IRQ 9: Reserved (see ATTENTI ON ->) IRQ 10: Reserved (see ATTENT ION ->) IRQ 11: Available IRQ 12: Available >DMI Event Logging Clear all DMI event logs: No Event Logging: Enabled Security ======== Set Supervisor Password Enter (Processor Serial Number) Disabled Power ===== Power State: Stay Off Power Savings: Disabled Standby Timeout: Off


README.PDF 40 / 46

Wakeup On Time: Disabled Time: 00:00:00 Wakeup On Modem Ring: Disabled Wakeup On LAN: Disabled >Hardware Monitor Boot ==== +Removable Devices +Hard Drive CD-Rom Drive Network Boot

RELEASE INFO 03/06 ( for internal user: see als o ECO )

1.Based on Release No.: 02/05 2.Requirements/Dependences Subpoints: Hardware D2-Motherboard Pri nt E Software - This BIOS is designed to provide the compl ete DMI-structure to keep track serial numbers etc for futur e use. For this reason the old structure in BIOS has to be deleted before the new structure can be installed. To acc omplish this there is a two times update-flash-procedur e needed for this version which is done automatically within the screen guided flash procedure. 3.Removed Errors/Error-No.: - Enhanced initializing of Environment Contr oller to avoid spurious slow down of CPU-speed, running R AM-test slow during PowerOnSelfTest - Some minor bug fixes 4.New Functions/enhanced Functions - Enhanced DMI structure to support serial n umbers etc in future - USB Boot Support for FD and TEAC CDROM - Setup Entrys Advanced: OnBoard LAN BootProm Advanced: QuickBoot Mode Advanced: >DMI Event Logging Power/HardwareMonitor: Fan Speeds 5.Functions under development/enhanced Functions - none 6.Additional remarks - This BIOS works for BEETLE CPU Pentium (D2 -CPU), acting as Standard Version to support standard applica tions. It will come up with the following signon te xt:


README.PDF 41 / 46

WN STD 03/06 11/09/2001 (D2) Use D2BIOS03.EXE to create a BIOS-Update-Flo ppy. Use D2CRIS03.EXE to create a BIOS-Recovery-F loppy. - Checksum: 6111h - ECO: 017 2475 01 - MODULNO1: 1750033326 - PROMSETPN: A3C80100352 - RAWMATPN: A3C40027674 - LABELTEXT: D2CPU

After corrupted checksum the BIOS will set its def ault to the following values: Main ==== Diskette A: 1.44 MB Diskette B: Disabled >Primary Master: Auto >Primary Slave: Auto >Secondary Master: Auto >Secondary Slave: Auto Local Bus IDE adapter: Both Speaker Volume Middle Advanced ======== Reset Configuration Data: No PS/2 Mouse: Disabled Large Disk Access Mode: DOS Legacy USB Support: Disabled ISA graphics device: No Boot-Video device: Onboard Onboard LAN BootProm: Enabled QuickBoot Mode: Disabled >I/O Device Configuration Serial Port A: Enabled Base I/O address / IRQ: 3F8/IRQ4 Serial Port B: Enabled Base I/O address / IRQ: 2F8/IRQ3 Parallel Port: Enabled Mode: Bi-directional Base I/O address: 378 Floppy Disk Controller: Enabled TouchScreen Routing: No Routing (IRQ-Routing COM3 COM4 COM3____ COM4__ __) >PCI/PNP ISA UMB Region Exclusion CC00 - CFFF: Available D000 - D3FF: Available D400 - D7FF: Available D800 - DBFF: Available DC00 - DFFF: Available >PCI/PNP ISA IRQ Resource Exclusion IRQ 3: Available IRQ 4: Available IRQ 5: Available IRQ 7: Available IRQ 9: Reserved (see ATTENTI ON ->) IRQ 10: Reserved (see ATTENT ION ->) IRQ 11: Available


README.PDF 42 / 46

IRQ 12: Available >DMI Event Logging Clear all DMI event logs: No Event Logging: Enabled Security ======== Set Supervisor Password Enter (Processor Serial Number) Disabled Power ===== Power State: Stay Off Power Savings: Disabled Standby Timeout: Off Wakeup On Time: Disabled Time: 00:00:00 Wakeup On Modem Ring: Disabled Wakeup On LAN: Disabled >Hardware Monitor Boot ==== +Removable Devices +Hard Drive CD-Rom Drive Network Boot

RELEASE INFO 01/01 ( for internal user: see als o ECO )

1.Based on Release No.: 00/00 2.Requirements/Dependences Subpoints: Hardware D2-Motherboard Pri nt E Software none 3.Removed Errors/Error-No.: - none 4.New Functions/enhanced Functions - none 5.Functions under development/enhanced Functions 6.Additional remarks - This BIOS is supporting the Standard Funct ions only - Display signon text: WN STD 01/01 (D2) 07/17/2001 - Checksum: 4F2Bh - ECO: 017155101


README.PDF 43 / 46

After corrupted checksum the BIOS will set its def ault to the following values: Main ==== Diskette A: 1.44 MB Diskette B: Disabled >Primary Master: Auto >Primary Slave: Auto >Secondary Master: Auto >Secondary Slave: Auto Local Bus IDE adapter: Both Speaker Volume Middle Advanced ======== Reset Configuration Data: No Installed O/S: Other PS/2 Mouse: Disabled Large Disk Access Mode: DOS Legacy USB Support: Enabled ISA graphics device No Boot-Video device Onboard >I/O Device Configuration Serial Port A: Enabled Base I/O address / IRQ: 3F8/IRQ4 Serial Port B: Enabled Base I/O address / IRQ: 2F8/IRQ3 Parallel Port: Enabled Mode: Bi-directional Base I/O address: 378 Floppy Disk Controller: Enabled TouchScreen Routing: No Routing (IRQ-Routing COM3 COM4 COM3____ COM4__ __) >PCI/PNP ISA UMB Region Exclusion CC00 - CFFF: Available D000 - D3FF: Available D400 - D7FF: Available D800 - DBFF: Available DC00 - DFFF: Available >PCI/PNP ISA IRQ Resource Exclusion IRQ 3: Available IRQ 4: Available IRQ 5: Available IRQ 7: Available IRQ 9: Reserved (see ATTENTI ON ->) IRQ 10: Available IRQ 11: Available IRQ 12: Available Security ======== Set Supervisor Password Enter Power ===== Power State Stay Off Power Savings: Disabled Standby Timeout: Off Wakeup On Time: Disabled Time: 00:00:00


README.PDF 44 / 46

Wakeup On Modem Ring: Disabled Wakeup On LAN: Disabled Boot ==== Removable Devices +Hard Drive CD-Rom Drive Network Boot

RELEASE INFO 00/00 ( for internal user: see also ECO )

1.Based on Release No.: --/-- 2.Requirements/Dependences Subpoints: Hardware D2-Motherboard Pri nt E Software none 3.Removed Errors/Error-No.: - none 4.New Functions/enhanced Functions - none 5.Functions under development/enhanced Functions - This version 00/00 still is under developm ent. FOR PROPER OPERATION THE FOLLOWING MUST BE DONE: - Onboard LAN controller must be available on D2-CPU board, (D2-LAN-Module or 3COM-LAN-Sandwich) - Setup entry "Power / Power Savings" must be set to [Disabled]; this also is the default aft er flashing the BIOS 6.Additional remarks - This BIOS is supporting the Standard Funct ions only - Display signon text: WN STD 00/00 (D2) 06/18/2001 - Checksum: 87BEh - When onboard LAN bridge is plugged in, def ault setting is: Intel (R) Boot Agent will show following s tartup text "Initialize Intel Boot Agent... PXE 2.0 Build... Press CTRL-S to enter Boot Agent setup" After corrupted checksum the BIOS will set its def ault to the following values: Main ==== Diskette A: 1.44 MB Diskette B: Disabled >Primary Master: Auto


README.PDF 45 / 46

>Primary Slave: Auto >Secondary Master: Auto >Secondary Slave: Auto Local Bus IDE adapter: Both Speaker Volume Middle Advanced ======== Reset Configuration Data: No Installed O/S: Other PS/2 Mouse: Disabled Large Disk Access Mode: DOS Legacy USB Support: Disabled ISA graphics device No >I/O Device Configuration Serial Port A: Enabled Base I/O address / IRQ: 3F8/IRQ4 Serial Port B: Enabled Base I/O address / IRQ: 2F8/IRQ3 Parallel Port: Enabled Mode: Bi-directional Base I/O address: 378 Floppy Disk Controller: Enabled TouchScreen Routing: No Routing (IRQ-Routing COM3 COM4 COM3____ COM4__ __) >PCI/PNP ISA UMB Region Exclusion CC00 - CFFF: Available D000 - D3FF: Available D400 - D7FF: Available D800 - DBFF: Available DC00 - DFFF: Available >PCI/PNP ISA IRQ Resource Exclusion IRQ 3: Available IRQ 4: Available IRQ 5: Available IRQ 7: Available IRQ 9: Reserved (see ATTENTI ON ->) IRQ 10: Available IRQ 11: Available IRQ 12: Available Security ======== Set Supervisor Password Enter Power ===== Power State Stay Off Power Savings: Disabled Standby Timeout: Off Wakeup On Time: Disabled Time: 00:00:00 Wakeup On Modem Ring: Disabled Wakeup On LAN: Disabled Boot ==== Removable Devices +Hard Drive CD-Rom Drive


README.PDF 46 / 46

Network Boot Intel (R) Boot Agent ...

Contents of DOWNLOAD · available as BEETLEview update packages, provided for older release LANDesk...

Documents

Transcript of Contents of DOWNLOAD · available as BEETLEview update packages, provided for older release LANDesk...