Contents at a Glance - caminstructor.comcaminstructor.com/files/www/contents-at-a-glance/Contents at...
Transcript of Contents at a Glance - caminstructor.comcaminstructor.com/files/www/contents-at-a-glance/Contents at...
Mastercam Training Guide
Contents at a Glance – Mill 2D Troubleshooting .................................................................... 1 Tips and Techniques ............................................................ 5 Setting the Environment ...................................................... 7 Lesson 1 ................................................................................ 17
Exercise 1a page 28
Exercise 1b page 29
Lesson 2 ................................................................................ 31
Exercise 2a page 56
Exercise 2b page 57
Mill 2D
Lesson 3 ................................................................................ 59
Exercise 3a page 99
Exercise 3b page 100
Lesson 4 ................................................................................ 101
Exercise 4a page 136
Exercise 4b page 137
Mastercam Training Guide
Lesson 5 ................................................................................ 139
Exercise 5a page 201
Exercise 5b page 202
Lesson 6 ................................................................................ 203
Mill 2D
Lesson 7 ................................................................................ 235
Exercise 7a page 312
Exercise 7b page 313
Lesson 8 ................................................................................ 315
Part 1
Part 2
Exercise 8a page 396
Exercise 8b page 397
Mastercam Training Guide
Feature Based Machining Lesson 1 .................................... 399
Feature Based Machining Lesson 2 .................................... 401
WCS-Part-1 ............................................................................ 403
WCS-Part-2 ............................................................................ 405
Mill 2D
WCS-Part-3 ............................................................................ 407
WCS-Part-4 ............................................................................ 409
Advanced Exercises ............................................................. 411
Also located on the DVD Advanced Exercise 1 ................................................................... 411
Advanced Exercise 2 ................................................................... 415
Mastercam Training Guide
Advanced Exercise 3 ................................................................... 419
What’s on the DVD?
1. Training Videos Getting Started - Video
an overview of how the CD works Setting the Mastercam Environment - Video Tips and Techniques – Videos including:
Getting Help – 7 Minutes
Mastercam Interface – 19 Minutes
Coordinate System – 10 Minutes
Creating Lines – 12 Minutes
Creating Arcs and Circles – 12 Minutes
Trim and Extend – 5 Minutes
Xform – 9 Minutes
Stock Setup – 8 Minutes
Backplot and Verify – 5 Minutes
Multi Passes and Depth of Cuts – 8 Minutes
And more videos on how to use Mastercam….
Lesson 1 through Lesson 8 - Videos
Demonstrations on how to complete each Lesson in the book Feature Based Machining - Videos
FBM-Lesson 1 – PDF file of Instructions and supporting Videos
FBM-Lesson 2 – PDF file of Instructions and supporting Videos WCS – Work Coordinate System
4 PDF Lessons and Videos Drawing-Files
Advanced exercises in .pdf format that can be printed out and used for extra practice Mastercam-Files
Mastercam files required by certain Lessons in the book
2. Mastercam HLE Installation Software Install it onto your computer so you can practice and work in Mastercam. Please note; Mastercam HLE Software is a full working copy of Mastercam, however it will NOT allow you to generate or save NC code.
Mill 2D
Mastercam Training Guide
Contents at a Glance Setting the Environment ...................................................... 1 Lesson 1 ................................................................................ 5
Exercise 1 ......................................................................... 43
Lesson 2 ................................................................................ 45
Exercise 2 .......................................................................... 85
Lathe
Lesson 3 ................................................................................ 87
Exercise 3 .......................................................................... 131
Lesson 4 ................................................................................ 133
Exercise 4 .......................................................................... 178
Mastercam Training Guide
Lesson 5 ................................................................................ 179
Exercise 5 .......................................................................... 229
Lesson 6 ................................................................................ 231
Exercise 6 .......................................................................... 281
Lathe
Lesson 7 ................................................................................ 283
Exercise 7 .......................................................................... 339
Lesson 8 ................................................................................ 341
Exercise 8 .......................................................................... On the CD
Mastercam Training Guide
Lesson 9 ................................................................................ 343
Exercise 9 .......................................................................... On the CD
Lathe
What’s on the CD/DVD?
1. Training Videos Getting Started-Video
An overview of how the CD/DVD works Setting the Mastercam Environment Tips and Techniques-Videos
Getting Help – 6 Minutes
Lathe Diameter & Radius – 7 Minutes
Creating Lines – 12 Minutes
Creating Arcs and Circles – 12 Minutes
Trim and Extend – 5 Minutes
Xform – 9 Minutes
Stock Setup – 8 Minutes
Backplot and Verify – 5 Minutes Lesson-1 through Lesson-9 Videos
Video instructions on how to complete each Lesson from start to finish. Mastercam-Files
Mastercam files required by certain Lessons in the book
Mastercam HLE Installation Software Install it onto your computer so you can practice and work in Mastercam. Please note; Mastercam HLE Software is a full working copy of Mastercam, however it will NOT allow you to create NC code.